To lock To unlock 1 P.T.O Fitting your child safe Roman blind with sidewinder Thank you for purchasing this product. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. It is recommended that this blind should only be installed by persons competent in DIY. Please note: Fixings will be required to install your blind depending on the mounting surface. Wallboard and plaster require the use of anchors such as expansion or toggle bolts. Brick, tile or stone need special plugs and drill bits, remember to always pre-drill holes in wood to avoid splitting. Positioning the blind A. Inside the recess The blind should be positioned in the centre of the recess ensuring that the gap at either end is the same. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind. B. Outside the recess The blind should be positioned so that equal lengths of the blind extend outside the left and right sides of the recess. Determine the installation point by extending the fabric fully, taking into consideration the window sill or any other factors. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind. 2 How to fit lever lock metal fixing brackets (B) 3 Top fixing or face fixing brackets The brackets supplied can be used to either top fix (ceiling) or face fix (wall) the blind. These are attached to the blind on delivery and need to be removed before fitting. To remove brackets from the blind, slide the lever anti-clockwise to release and then unclip. Mark out the fixings’ positions on the frame, wall or ceiling. Ensure the brackets are positioned so the blind will not be obstructed during operation by window handles, levers etc. Fix brackets into place using appropriate plugs and screws.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
3. Top Fixing or Face Fixing BracketsThe brackets supplied can be used to either top fix (ceiling) or face fix (wall) the blind. These are attached to the blind on delivery and need to be removed before fitting.
To remove brackets from the blind, slide the lever anti-clockwise to release and then unclip.
Mark out the fixing positions on the frame, wall or ceiling. Ensure the brackets are positioned so the blind will not be obstructed during operation by window handles, levers etc.
Fix brackets into place using appropriate plugs and screws.
4. Installing the BlindPlace the rail in a slightly tilted position and slide over the metal edge of the bracket. Press the rail back and slide the swivel lever back to lock the rail in place.
5. Operating the blindThe blind operates on a continuous loop chain. By pulling the front or back of the chain downthe blind will lower and lift as required, keep the chains vertical for smooth operation.
6. Rear Cord Safety DevicesYour blind fitted with two part breakaway devices on the lower rod pockets, each cord has two devices. Should these devices detach they will be retainedon the cord and can be simply clicked back in place.
, alternatively the knot may be placed directly on to item 7.
To lock To unlock
Thank you for purchasing this product. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. It is recommended that this blind should only be installed by persons competent in DIY.
Please note: Fixings will be required to install your blind depending on the mounting surface. Wallboard and plaster require the use of anchors such as expansion or toggle bolts. Brick, tile or stone need special plugs and drill bits, remember to always pre-drill holes in wood to avoid splitting.
1. Positioning The Blind
A. Inside The RecessThe blind should be positioned in the centre of the recess ensuring that the gap at either end is the same. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
B. Outside the RecessThe blind should be positioned so that equal lengths of the blind extend outside the left and right sides of the recess. Determine the installation point by extending the fabric fully, taking into consideration the window sill or any other factors. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
Fitting your child safe Roman blind with sidewinder
2. How to fit Lever Lock Metal Fixing Brackets (B)
Thank you for purchasing this product. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. It is recommended that this blind should only be installed by persons competent in DIY.
Please note: Fixings will be required to install your blind depending on the mounting surface. Wallboard and plaster require the use of anchors such as expansion or toggle bolts. Brick, tile or stone need special plugs and drill bits, remember to always pre-drill holes in wood to avoid splitting.
1. Positioning The Blind
A. Inside The RecessThe blind should be positioned in the centre of the recess ensuring that the gap at either end is the same. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
B. Outside the RecessThe blind should be positioned so that equal lengths of the blind extend outside the left and right sides of the recess. Determine the installation point by extending the fabric fully, taking into consideration the window sill or any other factors. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
Fitting your child safe Roman blind with sidewinder
2. How to fit Lever Lock Metal Fixing Brackets (B)
1
P.T.O
Fitting your child safe Roman blindwith sidewinder Thank you for purchasing this product. Please read the instructions and warnings carefully before use toensure safe and satisfactory operation of this product. It is recommended that this blind should only beinstalled by persons competent in DIY.
Please note: Fixings will be required to install your blind depending on the mounting surface. Wallboardand plaster require the use of anchors such as expansion or toggle bolts. Brick, tile or stone need specialplugs and drill bits, remember to always pre-drill holes in wood to avoid splitting.
Positioning the blind
A. Inside the recessThe blind should be positioned in the centre of the recess ensuring that the gap at either end is the same. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
B. Outside the recessThe blind should be positioned so that equal lengths of the blind extend outside the left and right sides of the recess. Determine the installation point by extending the fabric fully, taking into consideration the window sill or any other factors. A metal bracket (B) should be positioned approx. 8-10cms from each side, any other brackets, depending on the size of your blind, should be positioned equally along the length of the blind.
2How to fit lever lock metal fixing brackets (B)
3 Top fixing or face fixing bracketsThe brackets suppliedcan be used to eithertop fix (ceiling) or facefix (wall) the blind. These are attached tothe blind on deliveryand need to be removed before fitting.
To remove brackets from the blind, slide the leveranti-clockwise to release and then unclip.
Mark out the fixings’ positions on the frame, wall orceiling. Ensure the brackets are positioned so the blind will not be obstructed during operation bywindow handles, levers etc.
Fix brackets into place using appropriate plugs and screws.
3. Top Fixing or Face Fixing BracketsThe brackets supplied can be used to either top fix (ceiling) or face fix (wall) the blind. These are attached to the blind on delivery and need to be removed before fitting.
To remove brackets from the blind, slide the lever anti-clockwise to release and then unclip.
Mark out the fixing positions on the frame, wall or ceiling. Ensure the brackets are positioned so the blind will not be obstructed during operation by window handles, levers etc.
Fix brackets into place using appropriate plugs and screws.
4. Installing the BlindPlace the rail in a slightly tilted position and slide over the metal edge of the bracket. Press the rail back and slide the swivel lever back to lock the rail in place.
5. Operating the blindThe blind operates on a continuous loop chain. By pulling the front or back of the chain downthe blind will lower and lift as required, keep the chains vertical for smooth operation.
6. Rear Cord Safety DevicesYour blind fitted with two part breakaway devices on the lower rod pockets, each cord has two devices. Should these devices detach they will be retainedon the cord and can be simply clicked back in place.
, alternatively the knot may be placed directly on to item 7.
Order online or call 01394 775670
Loom & Last Ltd. (c) 2019www.loomandlast.com
4 Installing the blindPlace the rail in a slightly tilted position and slide over the metal edge of the bracket. Press the rail back and slide the swivel lever back tolock in place.
5 Operating the blindThe blind operates on a continuous loop chain.By pulling the front or back of the chain down the blind will lower and lift as required. Keep thechains vertical for smooth operation.
6 Rear cord safety devicesYour blind should be fitted with two-part breakaway devices (item 7) on the lower rod pockets, eachcord has two devices. Should these devices detach they will be retained on the cord and can be simplyclicked back in place. A toggle (item 9) can be used to level your blind and then tie a knot underneathas shown, alternatively the knot may be placed directly on to item 7.
7Internal chain breakaway safetymechanism
The blind is fitted with an internal breakaway coghousing the operating chain. Should the internal cog separate from the housing it can be inserted back into the blind by applying a firm and even pressure. The chain must be looped back on to the cog before it is re-inserted into the blind. The small metal stud on the cog should face to the end of the blind. Once inserted back into the housing the blind will operate normally.
3. Top Fixing or Face Fixing BracketsThe brackets supplied can be used to either top fix (ceiling) or face fix (wall) the blind. These are attached to the blind on delivery and need to be removed before fitting.
To remove brackets from the blind, slide the lever anti-clockwise to release and then unclip.
Mark out the fixing positions on the frame, wall or ceiling. Ensure the brackets are positioned so the blind will not be obstructed during operation by window handles, levers etc.
Fix brackets into place using appropriate plugs and screws.
4. Installing the BlindPlace the rail in a slightly tilted position and slide over the metal edge of the bracket. Press the rail back and slide the swivel lever back to lock the rail in place.
5. Operating the blindThe blind operates on a continuous loop chain. By pulling the front or back of the chain downthe blind will lower and lift as required, keep the chains vertical for smooth operation.
6. Rear Cord Safety DevicesYour blind fitted with two part breakaway devices on the lower rod pockets, each cord has two devices. Should these devices detach they will be retainedon the cord and can be simply clicked back in place.
, alternatively the knot may be placed directly on to item 7.
7. Internal Chain Breakaway Safety Mechanism
The blind is fitted with an internal breakaway cog housing the operating chain. Should the internal cog separate from the housing it can be inserted back into the blind by applying a firm and even pressure, the chain must be looped back on to the cog before it is re-inserted into the blind. The small metal stud on the cog should face to the end of the blind.Once inserted back into the housing the blind will operate normally.
The Natural Curtain Companywww.naturalcurtaincompany.com
7
9
7
9
7. Internal Chain Breakaway Safety Mechanism
The blind is fitted with an internal breakaway cog housing the operating chain. Should the internal cog separate from the housing it can be inserted back into the blind by applying a firm and even pressure, the chain must be looped back on to the cog before it is re-inserted into the blind. The small metal stud on the cog should face to the end of the blind.Once inserted back into the housing the blind will operate normally.
The Natural Curtain Companywww.naturalcurtaincompany.com
Re-insert intoheadrail
Related Documents
