SPECIFICATION INSTALLATION INSTRUCTIONS Note Note PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT Fitness Legacy Zone Rower 6210-079 14 to Adult <900mm Approx 141Kg Approx 187Kg 6210-079 Page 1 of 10 1560x1325x915mm Ensure all installation aids are removed before first use. Use Installation Aid (3720-185) for Below Ground Fixing. Steel plate to EN 10025 Steel CHS to EN 10219 Steel RHS to EN 10219 Welding to EN ISO 14341:2011 Polyester powder paint to EN 13438:2005 Standard fixings to BS 3692:2001 and BS 4190:2001 Non-standard fixings are anti-vandal and corrosion resistant 1 Read installation instructions thoroughly before commencing installation of unit. 2 Excavate two holes 600 x 600 x 600 deep - see page 2. 3 Position and assemble the below ground fixings with spragging irons (see page 2) centrally in the excavated holes so the eight bolts are pointing upwards ensuring that the top plate is flush with the finished surface level. 4 Check alignment of bolts and backfill the holes with concrete (0.41 cu Metres) (4 parts gravel, 2 parts sand & 1 part cement) ensuring the below ground fixing is perpendicular to the finished surface level. 5 Allow the concrete to set for 48 hours. 6 Position the unit on the below ground fixings and fit using one M20 washer, one M20 spring washer and one M20 nut per bolt as shown on page 3. Ensure unit is perpendicular to the ground surface. Ensure all moving parts move freely without obstruction. Centre punch thread in two places on all eight M20 Bolts and then fit nut cap (see page 3).
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SPECIFICATION
INSTALLATION INSTRUCTIONS
Note
Note
PROD. CODE
SIZE
AGE RANGE
F/ FALL HEIGHT
HEAVIEST PART
TOTAL WEIGHT
Fitness Legacy Zone
Rower6210-079
14 to Adult
<900mm
Approx 141Kg
Approx 187Kg
6210-079Page 1 of 10
1560x1325x915mm
Ensure all installation aids are removed before first use.
Use Installation Aid (3720-185) for Below Ground Fixing.
Steel plate to EN 10025Steel CHS to EN 10219Steel RHS to EN 10219Welding to EN ISO 14341:2011
Polyester powder paint to EN 13438:2005Standard fixings to BS 3692:2001 andBS 4190:2001Non-standard fixings are anti-vandal andcorrosion resistant
1 Read installation instructions thoroughly before commencing installation of unit.
2 Excavate two holes 600 x 600 x 600 deep - see page 2.
3 Position and assemble the below ground fixings with spragging irons (see page 2) centrally in theexcavated holes so the eight bolts are pointing upwards ensuring that the top plate is flush with thefinished surface level.
4 Check alignment of bolts and backfill the holes with concrete (0.41 cu Metres) (4 parts gravel, 2 partssand & 1 part cement) ensuring the below ground fixing is perpendicular to the finished surface level.
5 Allow the concrete to set for 48 hours.
6 Position the unit on the below ground fixings and fit using one M20 washer, one M20 spring washerand one M20 nut per bolt as shown on page 3. Ensure unit is perpendicular to the ground surface.Ensure all moving parts move freely without obstruction. Centre punch thread in two places on alleight M20 Bolts and then fit nut cap (see page 3).
6210-079
Page 2 of 10
FSL = Finished Surface Level
Below Ground Fixing Details(2 off)
Foundation Detail(Care must be taken in abnormal conditions)
TYP
FSL
60
0
30
0
1570
970 Ctrs300
600
600
(85
)
Concrete
SpraggingIrons
Note :- Ensure there are no high spots on groundbetween below ground fixings where rower would flex
Note :- Ensure both below ground fixings areinstalled flat and inline. FSL to be nohigher than below ground fixing plate
3
2
4
6210-079
Page 3 of 10
Rower to Below Ground Fixing Details
Centre punch thread in two placeson all eight M20 Bolts
8
7
6
5
6210-079
Page 4 of 10
Minimum and Training Spaces
150
0M
in8
53
Training Space
(970)1630
36
00
(85)
485
R1000
400Training Space
Minimum Space
2400
4400
Base Fixing
180
0
1800
R1500
6210-079
Page 5 of 10
Safety Surfacing
Wetpour
9.0 Sq. Metres 40mm Wetpour11.0 Linear Metres Wetpour Edging
Grass Mats(1500 x 1000mm)
11 off Total
Safety Tiles(1000 x 1000mm)
10.0 Sq. Metres40mm Thickness12.0 Linear Metres of Tile Edging
3510
30
75
1537
.5
(970)1465 1075
Front(Foot End)
RearR1500
4500
1700 (970) 1330
20
00
40
00
Rear
Front(Foot End)
300
0
15
00
(970)1750 1280
4000
RearFront(Foot End)
250
6210-079
Page 6 of 10
Fixing Details for Maintenance
Seat Frame Assembly
Handle and Pivot Arm Assembly
1.2.4
1.2.11 1.2.91.2.2
1.2.3
1.2.5
1.2.12
1.2.8
1.2.10
1.2.6
1.2.101.2.8 1.2.12
1.2.13
1.2.10
1.2.7
1.2.12
1.2.1
1.3.2 1.3.10
1.3.7
1.3.12
1.3.1
1.3.11
1.3.9
1.3.51.3.6
1.3.51.3.8
1.3.9
1.3.6
1.4.1
1.4.2
1.4.3
1.10
1.12
1.8
1.14
1.3.4
1.3.3
6210-079
Page 7 of 11
Fixing Details for Maintenance
Handle/Pivot Arm Assembly to Seat Frame Assembly
Rear Arm Assembly Front Arm Assembly
1.10
1.9
1.12
1.141.3
1.4
1.14 1.9
1.121.2
1.5.1
1.5.2
1.5.3
1.5.3
1.5.2
1.6.1
1.6.2
1.6.3
1.6.2
1.6.3
6210-079
Page 8 of 11
Fixing Details for Maintenance
Arm Assembly to Rower Frame and Seat Frame Assembly
1.6
1.5
1.11
1.121.8
1.14
1.13
1.7 1.15
1.1
1.14
1.8 1.12
1.15
1.71.13
1.6 Note:- Plates to be on inside(4 Places)
6210-079
Page 9 of 10
Parts List
ITEM QTY PART NUMBER DESCRIPTION
1 1 5104-031 Rower Assembly
1.1 1 4202-649 Rower Frame W.A.
1.2 1 4202-116 Seat Frame Assembly
1.2.1 1 4202-117 Seat Frame W.A.
1.2.2 2 3711-073 Foot Cast Iron
1.2.3 1 4202-753 Front Panel Assembly (12mm Panel)