FIRE DAMPER - Dasmal Trading LLCKAD Air Conditioning Est. P.O. Box 5389, Dubai, UAE. Tel: +971 4 806 7676 Fax: +971 4 806 7688 Email: [email protected] Web:

KAD Air Conditioning Est. P.O. Box 5389, Dubai, UAE. Tel: +971 4 806 7676 Fax: +971 4 806 7688 Email: [email protected] Web: www.kadairconditioning.com

klimaopremaHR-10430 Samobor,

Croatia, Gradna 78A.

Fire Damper

FD25FIRE DAMPER

All possible combinations of width and height are available. Standard dimensions are avaliable with increments of 50mm.

Min. dimensions B(W) x H [mm]

Max. dimensions B(W) x H[mm]

200x200 800x600

350

2

3

4

5

B

250

3030

30

120

30

H

6

1

• Fire resistance according to EN 1366-2, classified according to EN 13501-3, Declaration of performance given according to Anex III of Regulation No 305/2011

• Rigid wall: EI 90 (ve, i↔o)S• Flexible wall: EI 90 (ve, i↔o)S• Ceiling / floor: EI 120 (ho, i↔o)S

• Used for the isolation of duct penetrations between fire com-partments.

• Fire dampers consist of housing, fire-resistant damper blade and release mechanism.

• Casing made of galvanised sheet steel, damper blade made of special insulating material, damper blade shaft and push rod made of stainless steel, plastic plain bearings made of brass, seals made of polyurethane and elastomer.

FIRE DAMPER FD25

FIRE PROTECTION

DAMPER MODELS

FD25-M rectangular fire damper with electric actuator.

• thermoelectric activation (72°C) with electric actuator and re-turn spring

• integrated end switches • fully automatic operation• networking capability (MP-BUS, LonWorks, AS-i BUS)

Options: M230 – electric actuator AC 230V M24 – electric actuator AC/DC 24V

DIMENSIONS

fire damper housingdamper bladeelectric actuator: Belimo BLFthermo-electric tripping device (72°C)smoke sealintumescent strip

123456

Design changes reserved01

FIRE DAMPERS - FD25

s>80

Fire damper FD25 is suitable for installation in all types of rigid, flexible walls and ceilings. Installation should be performed according to the installation instructions provided by the manufacturer.

Installation steps:

1. Wall opening H(B)+160mm 2. Damper fixing (damper blade should be in a closed position during installation!) 3. Fill the gap between damper and wall with mortar

INSTALLATION IN RIGID WALL

standard gypsum plaster

During installation use wooden struts toprevent deformation of casing, caused by drying gypsium plaster.

z

137 Opening in the wall: (B+160) x (H+160)

Masterboard thickness 20mm

200

After installation check for damper blade mobility, preform an opening and closing test.

FIRE DAMPERS - FD25

02Design changes reserved

INSTALLATION IN FLEXIBLE WALL

INSTALLATION IN CEILING

120

z>125

200

s≥80


gypsum plasterboards (thickness 12,5mm)

mineral wool (density 50kg/m3)

CW metal profile

screw for gypsum plasterboard

Opening in the wall: (B+160) x (H+160)


137

After installation check for damperblade mobility, perform an opening andclosing test.

s>80

021521>z

200


Masterboard thickness20mm


731

After installation check for damperblade mobility, preform an opening andclosing test.


FIRE DAMPERS - FD25

SELECTION DIAGRAM

The values of total pressure loss for other sizes are obtained in a manner that read value from the graph is multiplied with the correc-tion value from the table. Value of sound power are obtained in a manner that read value is added the correction value from the table.

B [mm] 200 250 300 350 400 450 500 550 600 650 700 750 800

∆pt x 1,22 1,14 1,07 1,0 0,94 0,88 0,83 0,77 0,73 0,68 0,64 0,6 0,58

Lwa+ -1 -1 0 0 0 0 0 0 0 0 1 1 2

ORDERING KEY

Symbol: v ∆pt LWA

- air velocity in the duct [m/s]- total pressure loss [Pa]- sound power level [dB(A)]

Total pressure loss and sound power level for B=400:

FD25 400x300 M230 S G1- - --

Damper typeDamper dimensions B(W) x H [mm]

Mechanism type:R - manual mechanismE230 - solenoid actuator AC230VE24 - solenoid actuator AC 24VM230 - electric actuator AC230VM24 - electric actuator AC/DC 24VOptions:s - electric limit switches (indicating damper “OPEN” and “CLOSED”)z - electric limit switch (indicating damper “CLOSED”)o - electric limit switch (indicating damper “OPEN”)Grille:G1 - grid on one sideG2 - grid on both sides

FIRE DAMPERS - FD25


BELIMOBLF230

OPERATING INSTRUCTIONS

Damper is delivered in closed position. When electric actuator is connected to the power supply damper will open. When the damperreaches the end position (damper open), in which is it blocked, the electromotor will stop. Closing fire damper takes place automati-cally when a power failure occurs. Thermal tripping device that comes with fire damper causes power circuit break at a temperatureof 72 °C (inside or outside duct). If checking is needed for proper fuctioning of fire damper, pushing the switch on the thermal trippingdevice will close damper. When switch on tripping device is released, the damper will open.

Manual opening

Damper can be opened without connecting to a voltage with enclosed handle turning in the direction of the arrow on electric acuator(clockwise). Damper can be locked in the desired position by fast turning back handle a quarter of a turn (counterclockwise).To unlock the electromotor, turn handle clockwise for a quarter of a turn. If the handle is released, damper will be closed by returnspring. When damper is opened manually, electric actuator will not move the damper into closed position after power failure (ther-moelectric fuse).

switch for checking forproper fuctioning

handle for manual opening

Open position Closed position


FIRE DAMPERS - FD25

Belimo BLF24-T i BF24-T supply viasafety isolation transformer

1 negative (direct-current) or neutral (alternating current)2 positive (direct-current) or faze (alternating current)

S1 common micro switch closed damper

S2 normally closed micro switch closed damperS3 normally open micro switch closed damperS4 common micro switch open damperS5 normally closed micro switch open damperS6 normally open micro switch open damper

Tf1 temperature sensor on the outer side of the duct (ambienttemperature) max. 72°C

Tf2 temperature sensor on the inner side of the duct (temperaturein the duct) max. 72°C


S1 S2 S3 S4 S5 S6

<5° <80°

21

– +

T ~

BAE72B-STf1 Tf2 Tf3 LED

Type of Belimo actuator BLF24-T BLF230-T

Nominal voltage /power consumption

voltage AC/DC 24V, 50/60Hz AC 230V, 50/60Hz

opening 5 W 8 W

holding 2,5 W 3 Wfor wire sizing 7 VA 12,5 VA

End switch1 mA...3 A (0,5 A), DC

5 V...AC 250V1 mA...3 A (0.5 A), DC 5 V...AC 250 V

Running timemotor 40...75 s 40...75 sspring-return ~20 s ~20 s

Ambient temperature range max. 50°C

ELECTRICAL CARACTERISTICS AND WIRING SCHEME OF ELECTRICAL ACTUATOR BELIMO

FIRE DAMPERS - FD25


CONTACT US







Fire Damper

FIRE DAMPERFDC25


FIRE DAMPER - FDC25


• Rigid wall: EI 90 (ve, i↔o)S • Flexible wall: EI 90 (ve, i↔o)S • Ceiling / floor: EI 120 (ho, i↔o)S


• Fire dampers consist of housing, fire-resistant damper blade-and release mechanism.

• Casing made of galvanised sheet steel, damper blade made of special insulating material, damper blade shaft and push rod-made of stainless steel, plastic plain bearings made of brass, seals made of polyurethane and elastomer.

PROFIRE DAMPER FDC25

FIRE PROTECTION

DAMPER MODELS

FDC25-M cylindrical fire damper with electric actuator.

• thermoelectric activation (72°C) with electric actuator and return spring

• integrated end switches• fully automatic operation• networking capability (MP-BUS, LonWorks, AS-i BUS)


Standard diameters

Øn[mm] 100 125 160 200 250 300 315

fire damper housingdamper bladedamper blade rotation axiselectric actuator: Belimo BLFthermo-electric tripping device (72°C)smoke sealintumescent strip

1234567

425

Ø n-2

35(Dn=315)

1

4

3

270

Øn+100

2

5

6

7

40

DIMENSIONS

FIRE DAMPER - FDC25


Fire damper FDC25 is suitable for installation in all types of rigid, flexible walls, ceilings. Installation should be performed accordingto the installation instructions provided by the manufacturer.

Installation steps:

1. Wall opening Øn+160mm 2. Damper fixing (damper blade should be in a closed position during installation!) 3. Fill the gap between damper and wall with mortar


During installation use wooden struts toprefent deformation of casing becauseof mortar drying.

230z>100

s>80

standard concrete mortar

Wall opening: Øn+160 mm

Check the mobility of damper blade, test opening and closing of fire damper


FIRE DAMPER - FDC25


gypsum plaster



CW metal profile

screw for gypsum plasterboardlength >60 mm

s≥80

Z

120




230

z>125s>80


Ceiling/floor opening: Øn + 160

gypsum plaster


FIRE DAMPER - FDC25


SELECTION DIAGRAM

ORDERING KEY

Symbol: v ∆pt LWA

- air velocity in the duct [m/s]- total pressure drop [Pa]- sound power level [dB(A)]

FDC25 Ø 250 M230 S G1- - --

Damper type

Damper diameter Øn [mm]

Mechanism type:R - manual mechanismE230 - solenoid actuator AC230VE24 - solenoid actuator AC 24VM230 - electrical actuator AC230VM24 - electrical actuator AC/DC 24V

Options:s - electric limit switches (indicating damper “OPEN” and “CLOSED”)z - electric limit switch (indicating damper “CLOSED”)o - electric limit switch (indicating damper “OPEN”)

Grille (option):G1 - grid on one sideG2 - grid on both sides


FIRE DAMPER - FDC25

BELIMOBLF230



Manual opening




Open position Closed position

FIRE DAMPER - FDC25









S1 S2 S3 S4 S5 S6

<5° <80°

21

– +

T ~


Type of Belimo actuator BLF24-T BLF230-T


voltage AC/DC 24V, 50/60Hz AC 230V, 50/60Hz

opening 5 W 8 W

holding 2,5 W 3 Wfor wire sizing 7 VA 12,5 VA

End switch1 mA...3 A (0,5 A), DC

5 V...AC 250V1 mA...3 A (0.5 A), DC 5 V...AC 250 V

Running timemotor 40...75 s 40...75 sspring-return ~20 s ~20 s



CONTACT US







Fire Damper

FIRE DAMPERFD40


FIRE DAMPER - FD40


• Rigid wall: EI 120 (ve, i↔o)S• Flexible wall: EI 120 (ve, i↔o)S• Ceiling / floor: EI 120 (ho, i↔o)S

All possible combinations of width and height are available.Standard dimensions are avaliable with increments of 50mm.

Min. dimensions B(W) x H [mm]

Max. dimensions B(W) x H[mm]

200x200 1500x800


• Fire dampers consist of housing, fire-resistant damper blade and release mechanism.


FIRE DAMPER FD40

FIRE PROTECTION

DAMPER MODELS

FD40-M rectangular fire damper with electric actuator.

• thermoelectric activation (72°C) with electric actuator and return spring



DIMENSIONS

fire damper housingdamper bladeelectric actuator: Belimo B(L)Fthermo-electric tripping device (72°C)smoke sealintumescent strip

123456

350

2

3

4

5

B

250

3030

30

120

30

H

6

FIRE DAMPER - FD40


s>80

Fire damper FD40 is suitable for installation in all types of rigid, flexible walls and ceilings. Installation should be performed accordingto the installation instructions provided by the manufacturer.

Installation steps:

1. Wall opening H(B)+160mm 2. Damper fixing (damper blade should be in a closed position during installation!) 3. Fill the gap between damper and wall with mortar



During installation use wooden struts toprevent deformation of casing, causedby drying gypsium plaster or mortar.

z > 100

137 Opening in the wall: (B+160) x (H+160)


200



FIRE DAMPER - FD40

s>80

021521>z

200

120

z>125

200

s≥80




CW metal profile

screw for gypsum plasterboard


Masterboard thickness20mm





gypsum plaster or mortar

137

731After installation check for damperblade mobility, preform an opening andclosing test.


FIRE DAMPER - FD40


H=700

H=800

Grille:G1 - grid on one sideG2 - grid on both sides

SELECTION DIAGRAM

The values of total pressure loss for other sizes are obtained in a manner that read value from the graph is multiplied with the correc-tion value from the table. Value of sound power are obtained in a manner that read value is added the correction value from the table.

FD40 400x300 M230 S G1- - --

Damper typeDamper dimensions B(W) x H [mm]


ORDERING KEY

Symbol: v ∆pt LWA

- air velocity in the duct [m/s]- total pressure loss [Pa]- sound power level [dB(A)]

Total pressure loss and sound power level for B=400:

B [mm] 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000-1200

1200-1500

∆pt x 1,22 1,14 1,07 1,0 0,94 0,88 0,83 0,77 0,73 0,68 0,64 0,6 0,58 0,56 0,55 0,54 0,5 0,4

Lwa+ -1 -1 0 0 0 0 0 0 0 0 1 1 2 2 2 3 3 4

Mechanism type:R - manual mechanismE230 - solenoid actuator AC230VE24 - solenoid actuator AC 24VM230 - electric actuator AC230VM24 - electric actuator AC/DC 24V


FIRE DAMPER - FD40

BELIMOBLF230



Manual opening




CLOSED OPEN

DAMPER OPENDAMPER CLOSED

CLOSED OPEN

FD40-R

FIRE DAMPER - FD40









S1 S2 S3 S4 S5 S6

<5° <80°

21

– +

T ~


Type of Belimo actuator BLF24-T BF24-T BLF230-T BF230-T


voltage AC/DC 24V, 50/60Hz AC/DC 24V, 50/60Hz AC 230V, 50/60Hz AC 230V, 50/60Hz

opening 5 W 7 W 6 W 8 W

holding 2,5 W 2 W 3 W 3 W

for wire sizing 7 VA 10 VA 7 VA 12,5 VA

End switch 1 mA...3 A (0,5 A), DC 5 V...AC 250V

1mA...6A (3A), DC 5V...AC 250V

1 mA...3 A (0.5 A), DC 5 V...AC 250 V

1 mA...6 A (3 A), DC 5 V...AC 250 V

Running timemotor 40...75 s <120 s 40...75 s <140 s

spring-return ~20 s ~16 s ~20 s ~16 s



CLOSED OPEN CLOSED OPEN

Fire damper is delivered in closed position. To open the damper, handle should be turned in counter-clockwise direction to “OPEN”position. It is possible to close damper with solenoid. The damper is opened manually. Manual damper activation is intended forperiodic maintenance.

FD40-E


CONTACT US







Fire Damper

FIRE DAMPERFDC40

425

Øn-2

(Øn-20)/2-155

1

4 3

270 40


• Rigid wall: EI 120 (ve, i↔o)S • Flexible wall: EI 120 (ve, i↔o)S • Ceiling / floor: EI 120 (ho, i↔o)S


• Fire dampers consist of housing, fire-resistant damper blade-and release mechanism.


FIRE DAMPER FDC40

FIRE PROTECTION

DAMPER MODELS

FDC40-M cylindrical fire damper with electric actuator.

• thermoelectric activation (72°C) with electric actuator and re-turn spring



fire damper housingdamper bladedamper blade rotation axiselectric actuator: Belimo B(L)Fthermo-electric tripping device (72°C)smoke sealintumescent strip

1234567

DIMENSIONS

Standard diameters

Øn[mm] 100 125 160 200 250 300 315 355 400 500 630

Øn+100

2

5

6

7


FIRE DAMPER - FDC40

FIRE DAMPER - FDC40


230 z

s>80

Fire damper FDC40 is suitable for installation in all types of rigid, flexible walls, ceilings. Installation should be performed accordingto the installation instructions provided by the manufacturer.

Installation steps:

1. Wall opening Øn+160mm 2. Damper fixing (damper blade should be in a closed position during installation!) 3. Fill the gap between damper and wall with mortar


During installation use wooden struts toprefent deformation of casing becauseof mortar drying.






FIRE DAMPER - FDC40


gypsum plaster



CW metal profile

screw for gypsum plasterboardlength >60 mm

s≥80

Z

120




230

z>125s>80


Ceiling/floor opening: Øn + 160

gypsum plaster


FIRE DAMPER - FDC40


SELECTION GRAPH

Symbol: v ∆pt LWA

- air velocity in the duct [m/s]- total pressure drop [Pa]- sound power level [dB(A)]

ORDERING KEY

FDC40 Ø 250 M230 S G1- - --

Damper type

Damper diameter Øn [mm]

Mechanism type:R - manual mechanismE230 - solenoid actuator AC230VE24 - solenoid actuator AC 24VM230 - electrical actuator AC230VM24 - electrical actuator AC/DC 24V


Grille (option):G1 - grid on one sideG2 - grid on both sides


FIRE DAMPER - FDC40

BELIMOBLF230



Manual opening




CLOSED OPEN


CLOSED OPEN

FDC40-R

FIRE DAMPER - FDC40









S1 S2 S3 S4 S5 S6

<5° <80°

21

– +

T ~


Type of Belimo actuator BLF24-T BF24-T BLF230-T BF230-T


voltage AC/DC 24V, 50/60Hz AC/DC 24V, 50/60Hz AC 230V, 50/60Hz AC 230V, 50/60Hz

opening 5 W 7 W 6 W 8 W

holding 2,5 W 2 W 3 W 3 W

for wire sizing 7 VA 10 VA 7 VA 12,5 VA

End switch 1 mA...3 A (0,5 A), DC 5 V...AC 250V

1mA...6A (3A), DC 5V...AC 250V

1 mA...3 A (0.5 A), DC 5 V...AC 250 V

1 mA...6 A (3 A), DC 5 V...AC 250 V

Running timemotor 40...75 s <120 s 40...75 s <140 s

spring-return ~20 s ~16 s ~20 s ~16 s



CLOSED OPEN CLOSED OPEN

Fire damper is delivered in closed position. To open the damper, handle should be turned in counter-clockwise direction to “OPEN”position. It is possible to close damper with solenoid. The damper is opened manually. Manual damper activation is intended forperiodic maintenance.

FDC40-E


CONTACT US




FIRE DAMPER - Dasmal Trading LLCKAD Air Conditioning Est. P.O. Box 5389, Dubai, UAE. Tel: +971 4 806 7676 Fax: +971 4 806 7688 Email: [email protected] Web:

Documents