GUIDED BY : Mr. ASHWANI KR. PANDEY B.TECH,M.TECH Associate Professor PRESENTED BY : DEPARTMENT OF ELECTRONICS AND COMMUNICATIONS SAURABH KUMAR
Jul 19, 2015
GUIDED BY :
Mr. ASHWANI KR. PANDEY
B.TECH,M.TECHAssociate Professor
PRESENTED BY :
DEPARTMENT OF ELECTRONICS AND COMMUNICATIONS
SAURABH KUMAR
INTRODUCTION
• This project is designed for electronic voting machine by using the
fingerprint identification method.
• Here voters thumb impressions are used for identifying the voters.
• During voting when the voter keeps his/her thumb in the scanner,
the system will check whether it matches with pre stored
impressions in the database.
• If it matches then system will allow the voter to poll his vote and
otherwise prevent the voter from polling.
Why only Fingerprint ?
• Every person in this universe has unique fingerprint.
• Fingerprints are unique i.e. everyone is born with one, which states that fingerprints can be used for unique identification.
• Fingerprint scanner is a device for computer Security featuring superior performance, accuracy, durability based on unique NITGEN Fingerprint Biometric Technology.
• Fingerprints tech is widely used in banking, authentication etc…
• Reliable and trusted
Hence we opted for fingerprint technology in our project.
TECHNOLOGY BACKGROUND
In detail description of
• Block Diagram
• Power Supply
• Micro controller (AT89S52)
• MAX 232
• Finger Print Scanner (NITGEN FIM 3030)
• LCD
Block Diagram
Power Supply
Micro
Controller
AT89S52
Keypad
Finger Print
Module
MAX
232
Switch
LCD Display
Security Alarm
Power Supply
Step DownTransformer
BridgeRectifier
FilterCircuit
RegulatorSection
Power supply toAll sections
Microcontroller (AT89S52)
• A Micro controller development of reduces PCB size & cost of design .
• If a system is developed with a microprocessor, the designer has to go for external memory such as RAM, ROM, EPROM and peripherals.
• Which is Because it has 8 Kb on chip flash memory use sufficient for our application.
• Moreover ATMEL is the leader in flash technology in today’s market place and hence using AT 89S52 is the optimal solution.
MAX 232
• It is 16-Pin IC known as Voltage Converter or Line Converter.
• It converts the RS-232 levels of the Fingerprint Scanner to the TTL voltage levels of µC 8051.
• MAX Maxim Company232 Series number
• RS Recommended Standard was set by the Electronic Industries Association (EIA) in 1960.
• Using DB-9 (Data Bit) Pin connector, we’ll connect the MAX-232 to the Fingerprint Scanner.
• We can connect two devices at a time to the MAX-232.
Sub-Units of EVM
Features of AT89S52 :
• The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller.
• 4.0V to 5.5V Operating Range
• Fully Static Operation: 0 Hz to 33 MHz
• 256 x 8-bit Internal RAM
• 32 Programmable I/O Lines
• Three 16-bit Timer/Counters
• Eight Interrupt Sources
• Low-power Idle and Power-down Modes
• Fast Programming Time
Pin Description :
Fingerprint Scanner (NITGEN FIM 3030)
• The fingerprint scanner used here is NITGEN company based which is
the leading manufacturer of FIM(Finger identification Module)
• The methodology involves of storing the fingerprint images as
database and during voting the input image is matched using the
database
LIQUID CRYSTAL DISPLAY(LCD)
• The LCD display is used to display the messages during
the action.
• Here a 16x2 display is used, each character is made of
5x7 dot matrix.
• Displays have built in backlight(blue or green diodes)
Pictorial Representation
Step Down T/F
LCD Display (2X16)
µC AT89S52
MAX - 232
Buzzer
Key Board
EEPROM
Fingerprint Scanner NITGEN FIM 3030
DB – 9 Connector
ENDEND
CLEAR
DATA
MASTERMODE
LOAD FINGERPRINTS
SAVE FP’s
ADVANTAGES
• Low power consumption
• It is economical
• Less manpower required
• Time conscious, as less time required for voting and
counting
• Avoids invalid voting.
• Saves transportation cost due to its compact size.
• Convenient on the part of voter.
• EVM are no different than websites or software; they can be
penetrated and altered by a hacker.
• Overall cost is high, physical tampering could be possible.
• Computer software and systems can have problems that may
delay or even halt voting.
DISADVANTAGES OF EVM
LIMITATIONS
• The limitations of this projects are:
• The collection of fingerprints of all the voters is little difficult.
• Only fingerprints of the voters is identified instead of
identifying the persons
Conclusion
• The project “ELECTRONIC VOTING MACHINE USING
FINGERPRINT Tech” has been successfully designed and tested.
• This can bring a revolutionary change in the election procedures.
• It provide additional security.
• System completely reduces the chance of invalid votes.
• The system can be manufactured simply as well as cheap.