Figure 9.1 A spark tester looks like a regular spark plug with an alligator clip attached to the shell. This tester has a specified gap that requires at least 25,000 volts (25 kV) to fire. - PowerPoint PPT Presentation
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.1 A spark tester looks like a regular spark plug with an alligator clip attached to the shell. This tester has a specified gap that requires at least 25,000 volts (25 kV) to fire.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.2 A close-up showing the recessed center electrode on a spark tester. It is recessed 3/8 in. into the shell and the spark must then jump another 3/8 in. to the shell for a total gap of 3/4 in.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.4 Measuring the resistance of an HEI pickup coil using a digital multimeter set to the ohms position. The reading on the face of the meter is 0.796 kΩ or 796 ohms in the middle of the 500- to 1,500-ohm specifications.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.7 Connect the scopes current clamp around the feed wire for the primary side of the coil(s). Start the engine and view the current flow waveform. (Courtesy of Fluke Corporation)
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.8 An example of a good coil current flow waveform pattern. Note the regular shape of the rise time and slope. Duration of the waveform may change as the module adjusts the dwell. The dwell is usually increased as the engine speed is increased. (Courtesy of Fluke Corporation)
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.11 (a) A voltage waveform of a pickup coil at low engine speed. (b) A current waveform of the current through the primary windings of the ignition coil at low engine speed. (c) A voltage waveform of a pickup coil at high speed. (d) A current waveform through the primary winding of the ignition coil at high engine speed.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.12 An AC voltage is produced by a magnetic sensor. Most sensors should produce at least 0.1 volt AC while the engine is cranking if the pickup wheel has many teeth. If the pickup wheel has only a few teeth, you may need to switch the meter to read DC volts and watch the display for a jump in voltage as the teeth pass the magnetic sensor. (Courtesy of Fluke Corporation)
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.14b A dual-trace pattern showing both the low-resolution signal and the high-resolution signals that usually represent 1 degree of rotation. (Courtesy of Fluke Corporation)
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.15 A track inside an ignition coil is not a short, but rather a low-resistance path or hole that has been burned through from the secondary wiring to the steel core.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.16 The relationship between the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor is affected by wear in the timing gear and/or chain.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.20 A length of vacuum hose being used for a coil wire. The vacuum hose is conductive because of the carbon content of the rubber in the hose. This hose measures only 1,000 ohms and was 1 ft long, which is lower resistance than most spark plug wires. Notice the spark from the hose’s surface to the tip of a grounded screwdriver.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.21 A distributorless ignition system (DIS) can be checked by unplugging both spark plug wires from one ignition coil and starting the engine. The spark should be able to jump the 1-in.(25-mm) distance between the terminals of the coil. No damage to the coil (or module) results because a spark occurs and does not find ground elsewhere.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.22 Using a vacuum hose and a grounded test light to ground one cylinder at a time on a DIS. This works on all types of ignition systems and provides a method for grounding out one cylinder at a time without fear of damaging any component.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.24 Note where the high-voltage spark jumped through the plastic rotor to arc into the distributor shaft. Always check for a defective spark plug(s) when a defective distributor cap or rotor is discovered. If a spark cannot jump to a spark plug, it tries to find a ground path wherever it can.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.26 This rotor had arced through to the distributor shaft. The engine would not run above an idle speed and the spark from the coil could easily fire a spark tester.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.27 Carbon track in a distributor cap. These faults are sometimes difficult to spot and can cause intermittent engine missing. The usual cause of a tracked distributor cap (or coil, if it is a distributorless ignition) is a defective (open) spark plug wire.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.30 Measuring the resistance of a spark plug wire with a multimeter set to the ohms position. The reading of 16.03 kΩ (16,030 ohms) is okay because the wire is about 2-ft long. Maximum allowable resistance for a spark plug wire this long would be 20 kΩ (20,000 ohms).
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.33 When removing spark plugs, it is wise to arrange them so that they can be compared and any problem can be identified with a particular cylinder.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.34 A spark plug thread chaser is a low-cost tool that hopefully will not be used often, but is necessary to clean the threads before new spark plugs are installed.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.35 Since 1991, General Motors engines have been equipped with slightly (1/8 in. or 3 mm) longer spark plugs.This requires that a longer spark plug socket should be used to prevent the possibility of cracking a spark plug during installation.The longer socket is shown next to a normal 5/8 in. spark plug socket.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.37 Spark plug removed from an engine after a 500-mile race. Note the clipped side (ground) electrode. The electrode design and narrow (0.025 in.) gap are used to ensure that a spark occurs during extremely high engine speed operation. The color and condition of the spark plug indicate that near-perfect combustion has been occurring.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.39 New spark plug that was fouled by a too-rich air-fuel mixture. The engine from which this spark plug came had a defective (stuck partially open) injector on this one cylinder only.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.40 A water spray bottle is an excellent diagnostic tool to help find an intermittent engine miss caused by a break in a secondary ignition circuit component.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.43b The connector must be opened (disconnected) to check and/or adjust the ignition timing.On DIS/EDIS systems, the connector is called SPOUT/SAW (spark output/spark angle word).
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.44 The first mark indicates the direction the rotor is pointing when the distributor is in the engine. The second mark indicates where the rotor is pointing just as it is pulled from the engine.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.45 Typical engine analyzer hookup that includes a scope display. (1) Coil wire on top of the distributor cap if integral type of coil; (2) number 1 spark plug connection; (3) negative side of the ignition coil; (4) ground (negative) connection of the battery.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.51 Raster is the best scope position to view the spark lines of all the cylinders to check for differences. Most scopes display cylinder 1 at the bottom. The other cylinders are positioned by firing order above cylinder 1.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.52 Display is the only position to view the firing lines of all cylinders.Cylinder 1 is displayed on the left (except for its firing line, which is shown on the right).The cylinders are displayed from left to right by firing order.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.55 The relationship between the height of the firing line and length of the spark line can be illustrated using a rope. Because energy cannot be destroyed, the stored energy in an ignition coil must dissipate totally, regardless of engine operating conditions.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman
Figure 9.56 A dual-trace scope pattern showing both the power and the waste spark from the same coil (cylinders 1 and 6). Note that the firing line is higher on the cylinder that is under compression (power); otherwise, both patterns are almost identical.
Advanced Engine Performance Diagnosis, Fourth EditionJames D. Halderman