FARM PIECE WARE ROAD FARINGDON ROAD - A417 FARINGDON ROAD - A417 P01 EPR DJ Initial issue 30/09/19 P02 SNN DJ Shared Footway/cycleway lengths amended to OCC comments 08/10/201 9 NOTES 1. All dimensions and levels are in metres unless otherwise noted 2. This drawing is to be read in conjunction with the relevant Architect's/Engineer's drawings, specifications and CDM documentation 3. This drawings has been produced electronically and may have been photo reduced or enlarged when copied. Work to figured dimensions only (DO NOT SCALE). All dimensions to be checked on site. Any errors or omissions to be reported to the engineer immediately. 4. This drawing contains coloured lines / information that may not be clear if reproduced in black and white. 5. Digital copies of this plan can only be considered accurate if supplied directly by Infrastruct CS Ltd. S4 - TECHNICAL APPROVAL S4 DRAWN REV CHECK DRAWING TITLE ENGINEER SCALE @ A1 CLIENT Infrastruct CS Ltd PROJECT PROJECT DRAFT APPROVED SHEET NO. ISSUE DATE REVISION COMMENTS ORIGIN PHASE LEVEL TYPE ROLE NO. PROJECT NUMBER DATE STATUS REVISION Faringdon Road Stanford In The Vale Oxon 3122 FARW ICS RA XX DR C The Stables, High Cogges Farm, High Cogges, Witney, OX29 6UN - Tel: 01993 709709: [email protected] Where quality lives DavidWilsonHomes Shared Footway/Cycleway Consultation Plan - Ware Road Roundabout 007 P02 1/1 September 19 DJ EPR TST X:\ICS Jobs\3100 Jobs\3122-FARW-Faringdon-Ware Roads (DWH)\01 - Design\B - S278\3122-FARW-ICS-M2-C - S278 Roundabout.dwg 10.0m 1:200 0m 5m 1. All works to be in accordance with Specification for Highway Works and to the satisfaction of Oxfordshire County Council. 2. Where required, existing road markings shall be removed mechanically (NOT using Compressed Air) eg: Hydro Blasting or similar approved. 3. Existing road markings within Section 278 Works to be replenished as agreed with Oxfordshire County Council. 4. All signs shall have at least a minimum of 450mm between the edge of the sign and the kerb face. 5. All cycleway footway signs to be erected a minimum of 2.4m from the finished land to the bottom of the sign. 6. Sign post foundations to be ST4 concrete. Where quality lives DavidWilsonHomes S E W N TSRG 956 TSRG 956 New non-illuminated signs, shared pedestrians/cyclists mounted at height 2.4m to underside of sign. TSRG 956 TSRG 956 TSRG 956 New non-illuminated signs, shared pedestrians/cyclists mounted at height 2.4m to underside of sign. TSRG 956 ALL ADOPTABLE SECTION 278 WORKS SHALL BE CONSTRUCTED TO THE SATISFACTION OF OXFORDSHIRE COUNTY COUNCIL HIGHWAYS INSPECTORS Lining to tie into existing right turn lining TSRG 956 TSRG 956 Notes a. All works to be carried out in accordance with the approved drawings, the Specification For Highway Works and to the statisfaction of the approving highway authority inspectors. b. Road markings shall be laid out in accordance with the " Traffic Signs Regulations and General Directions 2016 " and the " Traffic Signs Manual Chapter 5 - 2003 " c. All redundant road markings shall be removed by Hydroblasting. d. All road signs shall be mounted a minimum clearance of 450mm from the carriageway channel or kerbline. e. Road sign locations shown are indicative and the final position shall be confirmed with the highway inspector. f. Road marking Specification - Type 1 (100m/m 2 /lux) g. Day visibility - Luminance factor of all white thermoplastic road markings shall be a minimum of 80 complying with Table 5 :Class IF6:BSEN1871. h. The lluminance factor of all yellow thermoplastic road markings shall be a minimum of 50 complying with Table 5 :Class IF6:BSEN1871. i. Night visibility - Immediately after application and throughout the period of 24months thereafter, reftroflectivity of all white thermoplastic road markings shall not be less than 100mcd/m 2 /lux, when measured in accordance with Table 2 : Class R2 of BSEN1871. j. Type 1 - 100mcd/m 2 /lux 2 year perfaormance specification is to be used for all general lining. Existing road markings to be removed during the resurfacing of the carriageway are not to be replaced. Only carriageway markings specified on this drawing are to be installed. TSRG 956 Area of existing segregated footway/cycleway to become shared S E W N 125m 1:2500 0m 62.5m