F9J1001au_8820au00838_N150_MR

7/30/2019 F9J1001au_8820au00838_N150_MR

1/38

U er M u

F9J1001au 8820au00838

WIRELESS modEm RoUTER

BASIC N 150

English

7/30/2019 F9J1001au_8820au00838_N150_MR

2/38

TablE Of COnTEnTs

gett st rted 1

Whats in the Box 1

Initial Setup 1Advanced Tools & Settings 6The Belkin Router Manager 7Manual Setup Using Your Browser 8Adding Computers to Your Network 9

gett to K ow Your Router 11

Front Panel 11Back Panel 12

Tec c Det 13

Technical Features 13System Requirements 14

U Your Router 15

Enabling Auto Update on Your Belkin Router 15Updating Your Router via Your System Tray (Windows) or Menu Bar(Mac) 17Updating the Router s Firmware via the Web Interface 18Resetting the Router 22Restor ing Your Router to Factory Default s 22Restoring the Router to Default Settings Using the Web Interface 23

Trou e oot d support

Troubleshooting

Technical Support

Re u tory i orm t o

FCC Statement

European Compliance Statement

7/30/2019 F9J1001au_8820au00838_N150_MR

3/38

1

W t t e box

Basic N150 Wireless Modem-Router

ADSL cable (attached to router)

Power supply (attached to router)

Ethernet cable

Network information card (attached to router)

Belkin Setup CD with User Manual

i t setup

W ere to P ce Your Router

For the best results, place the Router in an open locationaway from large metal objects and magnets such as thosefound in speakers Raising the Router above floor levelcan improve the strength of your wireless signal

gETTing sTaRTED

7/30/2019 F9J1001au_8820au00838_N150_MR

4/38

2

gETTing sTaRTED

how to set it Up

31 2

*Filter may be required

7/30/2019 F9J1001au_8820au00838_N150_MR

5/38

3

gETTing sTaRTED

1 Connect your Routers ADSL cable to your phone jack or phone- jack a dap ter (micro fil ter ) If you are rep lac ing an exi st ing Rou teror gateway, this may require unplugging the existing gateway

note: If required by your Internet Service Provider (ISP),plug the included phone-jack adapter (microfilter) into yourwall-mounted phone jack Please check with your providerbefore connecting your Router if you are unsure whether ornot you need to use the included phone-jack adapter

2 Plug the Routers power supply into a wall outlet

3 Put the CD into your computer If the CD doesntopen automatically, please browse to your CD driveand double-click on the Belkin Setup CD icon

4 Click the Setup icon on the CD menu

Setup

7/30/2019 F9J1001au_8820au00838_N150_MR

6/38

4

gETTing sTaRTED

5 After a brief installation, the setup software will ask youfor the network name and password from the networkinformation card that is attached to your Router Store the

card under the base of your Router for future reference

7/30/2019 F9J1001au_8820au00838_N150_MR

7/38

5

gETTing sTaRTED

6 A progress screen will appear while additional software isinstalled This may take a few minutes to complete Oncefinished, a Success message will appear indicating that you

are connected to the Internet via your new Belkin Router

Dur etup you m y e ked or dd t o orm t o

You may need to enter a username and password providedby your ISP This username and password is likely to befound on materials that came from your ISP when yousigned up for service If necessary, you may need to contactyour ISP to retrieve your username and password

If you have a static IP address, you may need to enteradditional information also provided by your ISP

If your computer doesnt have a wireless adapter, or thesetup software is unable to control it, you may be asked toconnect your computer to the Router with a network cable

If the setup software is unable to detect your VCI and VPIsettings based on your country, you may also need to enterthis information Your ISP is likely to have provided it

7/30/2019 F9J1001au_8820au00838_N150_MR

8/38

6

gETTing sTaRTED

adv ced Too & sett

After the initial setup is complete, you have the option tochange settings like your network name, security type, andpassword To make these changes and others, click on theAdvanced Tools icon at the CD Setup menu and select oneof the following settings that you would like to change:

network n me & secur ty Personalize your network name(SSID), password, and strength of wireless security

I ter et serv ce Prov der & lo sett Haveyou moved or changed Internet Service Providers?If youd like to change these settings without running

through the setup process again, this is the place

7/30/2019 F9J1001au_8820au00838_N150_MR

9/38

7

gETTing sTaRTED

T e be k Router M er

The Belkin Router Manager appears in your system tray(Windows) or menu bar (Mac) Its icon indicates the currentstatus of your Router and also allows you to access yourRouters settings to make changes It also provides quickaccess to software that came bundled with your Router

To access the Router settings, click on the iconand select from the menu that appears

The status of your Router is shown by the Belkin Router Managericon, which closely mimics the light on the front of the Routerb ue: You are connected to your Belkin Routerand it is connected to the Internetam er: You are connected to your Belkin Router,but it is not connected to the Internet

Router SettingsUser Manual

Network problem detected

Check for UpdatesOptionsExit

7/30/2019 F9J1001au_8820au00838_N150_MR

10/38

8

gETTing sTaRTED

In your browser, type http://router (you do not need to typein anything else such as www ) Then press the Enter key Ifyoure still having trouble running the manual setup option, type192 168 2 1 in your browser (you do not need to type in anythingelse such as http:// or ww w) Then press the Enter key

M u setup U Your brow er

7/30/2019 F9J1001au_8820au00838_N150_MR

11/38

9

gETTing sTaRTED

add Computer to Your network

Wireless devices such as computers, network printers, and gamingsystems can connect to your Router with a few simple steps

U t e CD

1 Put the Setup CD into your computer If the CD

doesnt open automatically, browse to your CDdrive and open the Belkin Setup CD icon

2 Click the Setup icon on the CD menu

3 After a brief installation, the setup software will ask you for thenetwork name and password from the network information cardthat came with your Router This card is most likely now locatedunderneath the foot of your Router in the provided card slot

4 A progress screen will appear while additional software isinstalled This may take a few minutes to complete Once

finished, a Success message will appear indicating that youare connected to the Internet via your new Belkin Router

note: The setup software runs only onWindows and Mac OS X systems

7/30/2019 F9J1001au_8820au00838_N150_MR

12/38

10

gETTing sTaRTED

M u y

If you choose not to use the included Setup CD for

adding additional computers or wireless devices, youcan manually add these items to your network

1 Locate the wireless-network-connections optionon your computer or wireless device

2 Select your Belkin Router from the list of available networks Youcan identify your Belkin Router by locating the network name(SSID) from the card located underneath the foot of your Router

3 Enter your network password (located onyour network information card)

Your wireless device will take a few moments to connect to yournetwork If the connection is not made the first time, try thisprocess again If you still have difficulty connecting to your networkafter trying this process a few times, see the Troubleshootingsection in this manual for help with connecting to your network

note: In some cases you may be prompted to select thesecurity type It is printed on the card for your convenience

U t e WPs butto

1 Start WPS Push Button Connection (WPS PBC) on your

computer or other Wi-Fi device that you would like to connectwirelessly to your Router Often there will be a button for thispurpose in software that came with the device, or a physicalWPS, PBC, or Security button on the device itself

2 Within two minutes, press the WPS button onyour Router and hold for two seconds

The WPS light (small light above WPS button) will blink blue while itlistens for your Wi-Fi device Once a connection is established, thelight will turn blue and then go out If a connection is not established,the light will blink amber You may repeat the process to try again

You can repeat this process for each WPS-enableddevice youd like to add to your network

7/30/2019 F9J1001au_8820au00838_N150_MR

13/38

A

B

11

gETTing TO KnOW YOUR ROUTER

a) Router st tu l t

Your Routers status is shown by the light on the front

O :The Router is not plugged into a power source

b k b ue:The Router is starting up

so d b ue: The Router is connected to the Internet

so d am er: The ADSL is detected but therouter is not connected to the internet

b k am er: Either th e ADSL (RJ11) cableis not plugged in, or there is no signal

b) W -f Protected setup (WPs) l t d butto

The WPS button on the front of your Router can be used to help establish a secure connection between your Router and other WPS-enabled Wi-Fi devices such as computers To use the WPS feature on your Router, see Getting Started > Adding Computers to Your Network > Using the WPS Button

The small light near the WPS button shows what is happening while you are using WPS to establish a connection

O :Idle

b k b ue:The Router is listening for a WPS-enabled computer or other device

so d b ue: The Router has made a secureconnection with the computer or other device

am er: A connection was not created

fro t P e

7/30/2019 F9J1001au_8820au00838_N150_MR

14/38

12

gETTing TO KnOW YOUR ROUTER

a) aDsl Co ector

Connect your Router to a phone jack using a telephone cord In some areas, a microfilter might be required

b) W red (lan) Co ector

Connect computers and other wired network devices to these ports using Ethernet cables

C) Re et butto

This button is used to restart your Router in rare cases when it functions incorrectly Resetting the Router will preserve your settings This button may also be used to restore the factory default settings Please see the Troubleshooting section for more information

D) Power Co ector

Connect the included powersupply to this jack

b ck P e

A

B

CD

7/30/2019 F9J1001au_8820au00838_N150_MR

15/38

13

TEChniCal DETails

Tec c fe ture

i te r ted aDsl2+ ModemThe integrated ADSL2+ modem allows you to connect to theInternet via your local Internet Service Provider (ISP) withoutinstalling and maintaining a separate DSL modem

i te r ted 802 11 W re e acce Po tThe N150 technology enhances your Routerswireless capabilities, allowing for data transfer speedsof up to 150Mbps across your network

naT iP addre s r

To save you the cost of adding IP addresses percomputer in your house, your Belkin Router uses NetworkAddress Translation (NAT) technology, allowing you toshare a single IP address across your network

sPi f rewYour Router is equipped with a firewall that will protect yournetwork from a wide array of common attacks and viruses

U ver P u - d-P y (UP P) Comp t tyThe UPnP (Universal Plug-and-Play) feature in your Routeroffers seamless operation of voice and video messaging,

games, and other applications that are UPnP-compliant

We -b ed adv ced U er i ter ceYou can easily make changes to your Routers advancedsettings through your web browser These changes canbe made from any computer on your network

be k Router Mo torThe Belkin Router Monitor application helps you to monitoryour Routers status and change network settings

i te r ted 4-Port 10/100 sw tcYour Router has a built-in, 4-port network switch toallow your wired computers to share: printers, data,MP3 files, digital photos, and much more

7/30/2019 F9J1001au_8820au00838_N150_MR

16/38

14

sy tem Requ reme t

Modem Router

Broadband ADSL Internet connection withRJ11 (telephone) connection

At least one computer with an installed network interface adapter

TCP/IP networking protocol installed on each computer

RJ11 ADSL telephone cable

Internet browser

setup so tw re

A computer running Windows XP SP3 or higher, Windows

Vista

, or Windows 7; or Mac OS

X v10 5 or v10 6 onlyMinimum 1GHz processor and 512MB RAM

600MB of free hard-drive space for installation

TEChniCal DETails

7/30/2019 F9J1001au_8820au00838_N150_MR

17/38

15

Using YOUR ROUTER

E auto Upd te o Your be k Router

The Router has the capability to automatically checkfor a newer version of firmware and alert you when itsavailable You can choose to download the new version orignore it By default this feature is disabled If you want toenable it, select Enable and click Apply Changes

note: We recommend you use a computer thathas a wired connection to the Router

setup tep :

1 Open a web browser on the computer

2 In the address bar of the web browser, type http://192 168 2 1

3 Click Login in the upper right-hand corner of the page TheRouter does not ship with a password, so just click Submit

7/30/2019 F9J1001au_8820au00838_N150_MR

18/38

16

Using YOUR ROUTER

16

5 Toward the lower-half side of the screen you willfind Auto Update Firmware Enabling

6 Select Enable by clicking the radio button and thenclick Apply Changes at the bottom of the screen

4 Click on System Settings in the left-handcolumn under the Utilities heading

7/30/2019 F9J1001au_8820au00838_N150_MR

19/38

17

Using YOUR ROUTER

17

Upd t Your Router v Your sy temTr y (W dow ) or Me u b r (M c)

Once you have completed the setup process, you will needto update the new software for your Router This can be doneeasily via your computers system tray or menu bar

setup tep :

1 Click on the green Belkin Router Manager icon (right-click forWindows) in your system tray (Windows) or menu bar (Mac)

2 Select Check for Updates or Update Available from the menu

3 You should now see the Belkin Updater window

4 Click on the Install Update icon

7/30/2019 F9J1001au_8820au00838_N150_MR

20/38

18

Using YOUR ROUTER

18

Upd t t e Router f rmw rev t e We i ter ce

The following steps show you how to update your Routersfirmware using its web interface You do not need to be connectedto the Internet as this interface is built into the Router itself

setup tep :

1 Locate and download the firmware file from the Belkinsupport site (Type your part number into the search box inthe top right corner and look for Firmware in the title )

2 Save the file to a location on your computer whereyou can get to it easily, such as your desktop

3 Connect the computer to one of the four LAN ports on the Router

7/30/2019 F9J1001au_8820au00838_N150_MR

21/38

19

Using YOUR ROUTER

19


5 In the address bar of the web browser, typehttp://192 168 2 1 and press Enter on your keyboard


7 Click on Firmware Update toward thebottom of the left-hand menu

7/30/2019 F9J1001au_8820au00838_N150_MR

22/38

20

Using YOUR ROUTER

20

8 Click the Browse button toward the middle of the

screen to search for the file you saved previouslynote: The firmware version in the images below isdepicted as an example Your file name will varydepending on your model and version

9 Select the firmware file by left-clicking on it and then clickthe Open button in the lower-right corner of the windowThis will take you back into the Routers interface

7/30/2019 F9J1001au_8820au00838_N150_MR

23/38

21

Using YOUR ROUTER

21

10 Click the Update button

11 A prompt asking, Are you sure youwant to continue with upgrading?will appear Click OK

12 A second prompt will open telling youthe Router will not respond duringthe upgrade and warning you notto remove the power supply fromthe Router Click OK once more

Congratulations The firmware has been updated successfully

7/30/2019 F9J1001au_8820au00838_N150_MR

24/38

22

Using YOUR ROUTER

Re ett t e Router

Re et butto RedThe Reset button is used in rare cases when the Routermay function improperly Resetting the Router will restore theRouters normal operation while maintaining the programmedsettings You can also restore the factory default settings byusing the Reset but ton Use the restore option in instanceswhere you may have forgotten your custom password

Re ett t e Router

Push and release the Reset button The lights on the Router will

momentarily flash The Router light will begin to blink Whenthe Router light becomes solid again, the reset is complete

Re tor Your Router to f ctory De u t

Press and hold the Reset button for at least 10 seconds,and then release it The lights on the Router will momentarilyflash The Router light will begin to blink When the Routerlight becomes solid again, the restore is complete

7/30/2019 F9J1001au_8820au00838_N150_MR

25/38

23

Using YOUR ROUTER

Re tor t e Router to De u tsett U t e We i ter ce

symptom

You need to restore the factory defaults using the web interfaceThis may be because the Router is not performing as expectedor you wish to remove all previously configured settings

setup tep


2 In the address bar of the web browser, type http://192 168 2 1


7/30/2019 F9J1001au_8820au00838_N150_MR

26/38

24

Using YOUR ROUTER

4 Click on Restore Factory Defaults in the left-

hand column under the Utilities heading

5 Click on the Restore Defaults button

7/30/2019 F9J1001au_8820au00838_N150_MR

27/38

25

Using YOUR ROUTER

6 A warning box will open that says, Warning: All your settingswill be lost Are you sure you want to do this? Click OK

7 The Router will begin the restoring process Oncethe restore is complete, the Router will reboot

note: This may take several minutes

Your Router has successfully been restored to its factory settings

7/30/2019 F9J1001au_8820au00838_N150_MR

28/38

26

TROUblEshOOTing anD sUPPORT

Trou e oot

T e setup CD doe ot utom t c y t rtIf Belkin Setup does not run when you insert the CD-ROM, yourcomputer may not be configured to open CDs automatically

If Belkin Setup does not appear within 15 seconds, browseto your CD-ROM drive and open the Belkin Setup iconAlternatively, you may visit http://router/ and perform thesetup manually Please see Manual Setup Using YourBrowser earlier in this manual for more information

be k setup c ot d my Router

If Belkin Setup is not able to communicate with your Router duringthe installation process, please check the following items

1 Make sure that the wireless hardware on yourcomputer is turned on, if available

2 Try connecting your computer to one of the four wiredports on the Router with an Ethernet cable

3 Ensure that the Router is on The front-panel light should be on

4 Unplug the Routers power supply for 10seconds, then plug it back in

5 There may be firewall software on your computer preventingan outgoing connection You may choose to temporarilydisable this software before attempting setup

If Belkin Setup still cannot find the Router, you might chooseto do a manual setup Refer to Manually ConfiguringNetwork Settings in this manual for details

7/30/2019 F9J1001au_8820au00838_N150_MR

29/38

27


be k setup c ot co ect my Router to t e i ter et

If Belkin Setup is not able to connect the Router tothe Internet, please check the following items:

1 Use the troubleshooting suggestions within Belkin Setup

2 If your ISP requires a user name and password, make sure thatyou have typed in your user name and password correctly Someuser names require that the ISPs domain may be at the end of thename Example: myname@myisp com The @myisp com part ofthe user name may need to be typed as well as your user name

3 If you continue to have no Internet connection, referto Manually Configuring Network Settings in thismanual for an alternative setup method

be k setup comp eted t t o , ut i c ot row e t eWe T e t o t e ro t o my Router k m er

1 Make sure the Router is connected to your modem with anEthernet cable via the Routers one WAN (modem) port

2 Unplug the modem from its power source and make surethat it goes dark Then reapply power to the modem

3 Unplug your Routers power supply, wait 10 seconds,and plug it back in This will cause the Router to tryto reestablish communication with the modem

7/30/2019 F9J1001au_8820au00838_N150_MR

30/38

28


be k setup comp eted t t o , ut i c ot row e t eWe T e t o t e ro t o my Router o d m er

1 Use the troubleshooting suggestions within Belkin Setup

2 If your ISP requires a user name and password, make sure thatyou have typed in your user name and password correctly Someuser names require that the ISPs domain may be at the end of thename Example: myname@myisp com The @myisp com part ofthe user name may need to be typed as well as your user name

3 If you have a static connection, your ISP will haveassigned you an IP address, subnet mask, and gatewayaddress Please re-run Belkin Setup and enter thisinformation when a static connection is mentioned

4 You may need to configure your Router to meetthe specific requirements of your ISP To searchour knowledge base for ISP-specific issues, go to:http://www belkin com/support and type in ISP

5 If you continue to have no Internet connection, referto Manually Configuring Network Settings in thismanual for an alternative setup method

i c t co ect to t e i ter et w re e y

If the light on the front of the Router is solid blue, then yourRouter is connected to the Internet You may not be connectedto the Routers wireless network Please refer to AddingComputers to Your Network in this manual for instructions

If your Windows XP computer is running SP2, you willnot be able to set up the Router via the wireless setupprocess You will need to either update to Windows XPSP3 or complete the setup via a wired connection

7/30/2019 F9J1001au_8820au00838_N150_MR

31/38

29


i c t co ect to t e i ter et w re e y d myetwork me ot ted av e network

1 Verify that your Router is on and thefront-panel light shows solid blue

2 If you are far from the Router, you might try movingcloser to see if you might have been out of range

3 Using a computer attached to the Router via a network cable,visit http://router/ and ensure that Broadcast SSID is ONThis setting is found on the Channel and SSID page

My w re e etwork per orm ce ow, co te t,u er rom we k , or im v d cu ty m t

VPn co ect o

Wireless technology is radio-based, which means connectivityand the throughput performance between devicesdecreases when the distance between devices increasesOther factors that will cause signal degradation (metal isgenerally the worst culprit) are obstructions such as wallsand metal appliances Note also that connection speed maydecrease as you move farther away from the Router

In order to determine if wireless issues are related torange, we suggest temporarily moving the computerwithin 10 feet from the Router if possible

C t e w re e c e Depending on localwireless traffic and interference, switching the wirelesschannel of your network can improve performance andreliability See the section titled Changing the WirelessChannel for instructions on how to choose other channels

7/30/2019 F9J1001au_8820au00838_N150_MR

32/38

30


ive t ed t ew Router d ome o my etwork c e t(computer , me co o e , etc ) re ow u e to co ect

Your new Router came pre-configured with a network name andpassword, found printed on an attached card All clients must use thisnetwork name and password to connect wirelessly to your RouterYou will need to find the network settings on your client, select thenetwork name printed on the card from the list of available networks,and enter the password when prompted to join the wireless network

l m t t e w re e tr m t r te Limiting the wireless transmitrate can help improve range and connection stability Most wirelesscards have the ability to limit the transmission rate To change thisproperty in Windows, go to the Windows Control Panel, open NetworkConnections, and double-click on your wireless cards connection Inthe properties dialog, select the Configure button on the Generaltab, then choose the Advanced tab and select the rate property

Wireless client cards are usually set to automatically adjustthe wireless transmit rate for you, but doing so can causeperiodic disconnects when the wireless signal is too weak; asa rule, slower transmission rates are more stable Experimentwith different connection rates until you find the best onefor your environment Note that all available transmissionrates should be acceptable for browsing the Internet Formore assistance, see your wireless cards user manual

7/30/2019 F9J1001au_8820au00838_N150_MR

33/38

31


Doe t e Router upport W re eProtected acce (WPa) ecur ty?

The Router ships with WPA/WPA2 security turned onWindows XP and some older network hardware mayrequire a software update to support WPA/WPA2

i m v d cu ty ett up WPa ecur ty o my Router

1 Log in to your Router by visiting http://router/ with your web browserClick on the Login button in the top right-hand corner of thescreen You will be asked to enter your password If you have neverset a password, leave the Password field blank and click Submit

2 Click Wireless in the left-hand menu Thenclick Security just below that

3 Select the WPA/WPA2 option

4 Enter a password This can be from 863 characters of your choice,including spaces and punctuation, OR a 64-digit hexadecimalnumber (using only the numbers 09 and letters AF)

5 Click Apply Changes to finish Your wirelessconnection is now encrypted Each computer using yourwireless network will need to use the new key

note: If you are configuring the Router over a wirelessconnection, you will have to re-connect to theRouter after changing any security set tings

note: Some older networking hardware supportsonly WEP encryption If your older computers cannotconnect to your network, try 128-bit or 64-bit WEP, orseek software updates from their manufacturers

7/30/2019 F9J1001au_8820au00838_N150_MR

34/38

32


i m v d cu ty ett up W red Equ v e tPr v cy (WEP) ecur ty o my Router

1 Log in to your Router Visit http://router/ with your web browserClick on the Login button in the top right-hand corner of thescreen You will be asked to enter your password If you have neverset a password, leave the Password field blank and click Submit

2 Click Wireless in the left-hand menu Thenclick Security just below that

3 Select the 128-bit WEP option

4 You may type in a WEP key manually, or generate one froma passphrase Type a phrase in the Passphrase field andclick the Generate button A WEP key is composed of 26hexadecimal digits (09, AF For example, C3 03 0F AF4B B2 C3 D4 4B C3 D4 EE 74 is a valid 128-bit WEP key

5 Click Apply Changes to finish Your wirelessactivity is now encrypted Each computer using yourwireless network will need to use the new key

note: If you are configuring the Router over a wirelessconnection, you will have to re-connect to theRouter after changing any security set tings

note: Some older networking hardware supportsonly 64-bit WEP encryption If your older computerscannot connect to your network, try 64-bit WEP

7/30/2019 F9J1001au_8820au00838_N150_MR

35/38

33


Tec c support

Us

http://www belkin com/support

UKhttp://www belkin com/uk/support

au trhttp://www belkin com/au/support

new Ze dhttp://www belkin com/au/support

Europehttp://www belkin com/uk/support

s pore1800 622 1130

M y1 800 812 076

i d1800-419-5546

T d

0018004413318

P pp e180014410282

ho Ko30021318

C800 819 0159

au tr1800 235 546

new Ze d0800 235 546

a emasia-support@belkin com

Kore emkoreasupport@belkin com

7/30/2019 F9J1001au_8820au00838_N150_MR

36/38

34

REgUlaTORY infORMaTiOn

fCC st teme t

DEClaRaTiOn Of COnfORMiTY WiTh fCC RUlEs

fOR ElECTROMagnETiC COMPaTibiliTYWe, Belkin International, Inc , of 12045 E Waterfront Drive, PlayaVista, CA 90094, declare under our sole responsibility that the device,f9J1001 v1 , complies with Part 15 of the FCC Rules Operation issubject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation

C ut o : Expo ure to R d o freque cy R d t oThe device shall be used in such a manner that the potentialfor human contact normal operation is minimized

This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment Thisequipment should be installed and operated with a minimumdistance of 20cm between the radiator and your body

feder Commu c t o Comm o not ceThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCCRules These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation

This equipment generates, uses, and can radiate radio frequencyenergy, and if not installed and used in accordance with theinstructions, may cause harmful interference to radio communicationsHowever, there is no guarantee that interference will not occurin a particular installation If this equipment does cause harmfulinterference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try andcorrect the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different

from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expresslyapproved by the party responsible for compliance couldvoid the users authority to operate this equipment

This device and its antenna(s) must not be co-located or

operating in conjunction with any other antenna or transmitter

7/30/2019 F9J1001au_8820au00838_N150_MR

37/38

35

REgUlaTORY infORMaTiOn

C d -i du try C d (iC)

The wireless radio of this device complies with RSS 139 & RSS 210Industry Canada This Class B digital apparatus complies withCanadian ICES-003

Operation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept anyinterference, including interference that may cause undesiredoperation of the device

Cet appareil numrique de la classe B conforme la norme NMB-003du Canada

For information on product disposal please refer tohttp://environmental belkin com

Europe Comp ce st teme t:

Belkin International hereby declares that this F9J1001 Wireless Router is in compliance with the essential requirements and otherrevelant provisions of the RTT&E Directive 1999/5/EC, the EMCDirective 2004/108/EC, and the Low Voltage Directive 2006/5/ECConformity was assessed using a Technical Construction File

A copy of the European Union CE marking Declaration ofConformit y may be obtained at the website: www belk in com/doc

7/30/2019 F9J1001au_8820au00838_N150_MR

38/38

2011 Belkin International, Inc All rights reserved A ll trade names are registered tr ademarks ofrespective manufacturers listed Mac, Mac OS, and Safari are trademarks of Apple Inc , registered in theU S and other countries Windows, Windows Vista, Internet Explorer, and DirectX are either registeredtrademarks or trademarks of Microsoft Corporation in the United States and/or other countries

F9J1001au_8820au00838_N150_MR

Documents