F-07868-00016-SB

eçééÉ=eçééÉ=eçééÉ=eçééÉ=j~êáåÉj~êáåÉj~êáåÉj~êáåÉ=

Software Description

Document No. Designation Revision Issue

F-07868-00016-SB log-files download SD-card 1.5 10. 02.2015

Name: ba.marquardt 1/12

Date: 01.04.2014

Hoppe Marine GmbH Kieler Straße 318 22525 Hamburg Germany Tel. +49-40-561949-0 Fax +49-40-561949-99 [email protected] www.hoppe-marine.com

Download of SD-card log-files and software updates

Project: FLUME® Stabilization System Document: F-07868-00016-SB.doc Strictly Confidential This document contains confidential and proprietary information of Hoppe Marine GmbH. Any reproduction, disclosure, or use in whole or in par t is expressly prohibited, except as may be specifically authorized by prior written agreement or permission.






Date: 01.04.2014

Rev. Status Date Description of Change Issued by A pproved by

1.1 Created 04/04/2014 Created S.Winkler S.Winkler

1.2 - 02/12/2014 Update system parameter added Ba.Marquardt Ba.Marquardt






Date: 01.04.2014

1 General Description

The FLUME® Stabilization System is equipped with a monitoring and control display unit located in the wheel house. The display unit - called HOMIP - has one SD-card access connection which is located on the side of the unit as shown in the figure below. Else, it has 2 Ethernet ports and 2 USB ports

Display Unit HOMIP

Access Connections

2 SD Card Access

2.1 Direct SD Card Access

The log-files are located on the SD-card and can be accessed through the following steps: [A] CAUTION: Power of HOMIP PLC needs to be turned off before SD-card can be removed. If

not SD-card might be damaged and data files might be lost. To make the system powerless switch off all fuses in the main cabinet. Alternatively you can unplug the green power plug directly at the HOMIP. Both possibilities are indicated in the following pictures






Date: 01.04.2014

[B] The SD-card access connection is located on the top-side at the back of the HOMIP. [C] The SD-card can be simply removed by pushing gently in the direction of the access

connection. [D] The log-files are located in a folder in the root directory of the SD-card. They are stored in

different types of subfolders for each tank of the system installed and for the inertial measurement system. Every day a new set of log-files is saved in a monthly folder and every month new subfolders are created. Depending on the number of tanks, the files are stored in the following notation:

a. TF_log_HOS1-yyyy-mm\ TF_log_HOS1-yyyy-mm-dd.log (inertial measurement of roll) b. TF_log_TK1-yyyy-mm\ TF_log_TK1-yyyy-mm-dd.log (parameters tank 1) c. TF_log_TK2-yyyy-mm\ TF_log_TK2-yyyy-mm-dd.log (parameters tank 2) d. TF_log_TK3-yyyy-mm\ TF_log_TK3-yyyy-mm-dd.log (parameters tank 3) e. …

[E] Copy all folders including text files to an alternative storage medium and provide the files to Hoppe Marine.

[F] After successful copying of the files please insert empty SD-card into the HOMIP. [G] The power off the HOMIP can be switched back on and the log-function will proceed

automatically.






Date: 01.04.2014

2.2 Remote Access to SD Card

Another possibility to access the files on the SD card is possible from the Main Cabinet. In case when the Bridge PLC is difficult to reach for example, it might be the easier way to download the data via a patch cable.

1. Change IP address of your Computer, in order to be integrated in the “Flume network”. (See section Error! Reference source not found. in F-07868-00027-SB, if you do not know exactly how to change the IP adress)

2. Connect patch cable to Ethernet switch in the main cabinet

3. Open a normal internet Browser and type in the IP address of the PLC (HOMIP):

192.168.2.101

4. The following page will be displayed:






Date: 01.04.2014

5. From this page you can access the files stored on the SD-card by choosing the link “Log Files on SD-Card”.

3 Software update and parameters safe and restore

This section describes how to save and restore parameters and how to update the Hoppe Marine PLC, HOMIP. For information of the software installed at the moment, press on the “FLUME” logo on the start screen. Software update files and parameter files for the updates have to be installed on a USB stick. The files have to be installed directly on the stick (root directory) and not in any folders. Otherwise, the files are not accessible by the PLC. Before any update of software or parameters is possible, this USB stick must be connected to the HOMIP PLC. Use the USB ports (port 2) below the display unit, to connect the USB device.

Insert the USB-stick into the middle slot (2) at HOMIP

3.1 Software Update (Select File)

Before making a software update, it is recommended to save a parameter file on an USB stick -

Section 3.3. If any settings are getting lost during the software update, you can restore them easily

be reloading this parameter file.






Date: 01.04.2014

1. Start Screen

This image will appear on the touch screen display once

the system has booted. Pressing the Menu button on the

start screen will bring up the Main Menu.

2. Main Menu

Pressing the System button will bring up the System

Service menu. However, before reaching the system

service menu you will have to enter a PIN

3. PIN Access

For the System menu the PIN has been set to 3333 for the

security level 3. Press Enter button. (For security level 4

press 4444, and so on.)

4. System Service

Pressing the update button will bring up a list of available

software updates stored in the root path of the USB-

device.






Date: 01.04.2014

5. Available Software Updates

All software updates, stored on the USB stick should be

visible in a list now. Highlight the desired file and press the

enter key to upload the software update from the

USB-device.

6. System Reboot

After pressing the enter key the system will automatically reboot and install the new

software. The system parameters (e.g. operational liquid level graph, liquid density settings, zero

settings pressure sensor, etc.) remain unchanged. Anyway, please check the parameters after

the update.

Note: Before physically disconnecting the USB-device form the HOMIP be sure to Release USB .

The command Release USB can be found under the System Service menu. (Please see last

section of this document)

3.2 Read Parameter Files

1. Start Screen



start screen will bring up the Main Menu.

FSxxxxxxAx.tgz






Date: 01.04.2014

2. Main Menu


Service menu.

3. System Service

Pressing the Parameter button will bring up the

Parameter menu.

4. Parameter Menu

Press Load from USB to read an existing parameter file

from USB-device. The name of a parameter file has the

notation:

xxxxx_xxxxx_TF_TKX_dd.mm-xxxxxx-hhmm.par

Chose the desired file from a list to load the parameters

into the system.








Name: ba.marquardt

10/12

Date: 01.04.2014

3.3 Save Parameter Files

5. Start Screen



start screen will bring up the Main Menu

6. Main Menu


Service Menu.

7. System Service

Pressing the Parameter button will bring up the

Parameter menu.

8. Parameter Menu

Press Save on USB to store a current parameter file to

an USB-device.





Name: ba.marquardt

11/12

Date: 01.04.2014




3.4 Release USB-Device

If a USB-device has been used to update or store information parameter it has to be “released” by

the software before it can be physically removed. Pressing the Release USB button in the System

Service or the Parameter menu starts the script to finalize writing all information onto the USB-

device and disconnects.

1. Start Screen



start screen will bring up the Main Menu with the

following options.

2. Main Menu


Service menu with the following options.





Name: ba.marquardt

12/12

Date: 01.04.2014

3. System Service

Press the Release USB button. The device can be

physically removed.

F-07868-00016-SB

Documents

card logfiles

marquardt e

sd card access

direct sd card

download of sd

sdcard access connection

sb logfiles

following pictures e