EX3600-6 SPECIFICATIONS - · PDF fileEX3600-6 SPECIFICATIONS ENGINE Make Cummins Model QSK60-C Type 4 cycle Aspiration Turbocharged and after cooled, direct injection chamber-type

EX3600 -6 SPECIFICATIONS

B A C K H O E B U C K E T C A PA C I T Y :( S A E H E A P E D ) : 2 8 . 8 Y D 3 ( 2 2 . 0 M 3 )

S H O V E L B U C K E T C A PA C I T Y ( H E A P E D ) : S A E ( 2 : 1 ) : 2 7 . 5 – 3 0 . 0 Y D 3 ( 2 1 . 0 – 2 3 . 0 M 3 )

O P E R A T I N G W E I G H T: B A C K H O E 7 9 5 , 9 0 0 L B . ( 3 6 1 0 0 0 K G )L O A D I N G S H O V E L 7 9 1 , 5 0 0 L B . ( 3 5 9 0 0 0 K G )

R A T E D P O W E R : 1 , 9 4 4 H P ( 1 4 5 0 K W )

S TA N D A R D E Q U I P M E N T

Engine140 A alternator

Heavy-duty type air cleaner with dust ejector

Cartridge-type engine oil filter

Cartridge-type engine oil bypass filter

Cartridge-type fuel filter

Fan guard

Isolation-mounted engine

Auto-idle engine

Emergency engine stop system

Hydraulic drive cooling-fan system

Hydraulic SystemE-P control system

OHS (Optimum Hydraulic System)

FPS (Fuel-saving Pump System)

Hydraulic drive cooling-fan system

Forced-lubrication and forced cooling pump

drive system

Control valve with main relief valve

Suction filter

Full-flow filter

Bypass filter

Pilot filter

Drain filter

High-pressure strainer

CabSturdy cab with top guard conforming to ISO

(OPG Level II)

Fluid-filled elastic mounts

Laminated glass windshield

Reinforced/tinted (bronze color) side and rear

windows

Parallel-link-type intermittent windshield wiper

Front windshield washer

Adjustable reclining seat with air suspension

Footrest

Air horn with electric compressor

Auto-tuning AM-FM radio with digital clock

Seat belt

Storage spaces

Floor mat

Auto air conditioner with defroster

Rearview mirror

Evacuation hammer

Emergency escape device

Trainer's seat

Pilot control shut-off lever

Monitor SystemsMeters

Hour-meter

Fuel gauge

Hydraulic oil temperature gauge

Engine coolant temperature gauge

Tachometer

Engine oil pressure gauge

Engine oil temperature gauge

Battery voltage gauge

Ambient temperature

Warning Indicators

Alternator

Engine stop

Coolant overheat

Hydraulic oil level

Auto lubrication

Fast-filling

Tension

Electric lever

Emergency engine stop

Top valve

Engine over run

Coolant level

Engine oil pressure

Pump transmission oil level indicator

Exhaust temperature

Fuel temperature

Engine warning

Hydraulic oil overheat

Stairway position

Electrical equipment box

Pump contamination

Air cleaner restriction

Satellite data transmitting system

Data Logging SystemDLU (Data-logging unit) continuously records

performance of the engine and the hydraulic

system. The record can be downloaded by PC

and PDA.

Lights9 working lights, 2 entrance lights,

7 maintenance lights, 2 cab lights

UpperstructureLockable machine covers

88,630 lb. (40 200 kg) counterweight

Hydraulic drive grease gun with hose reel

Retractable ladder with spring type balancer

Swing parking brake

UndercarriageTravel parking brake

Travel motion alarm device

Hydraulic track adjuster with N2 gas accumulator

and relief valve

50 in. (1 270 mm) triple grouser shoes

MiscellaneousStandard tool kit

ISO conforming stairs and handrails

Recirculation air filter for air conditioner

Ventilation air filter for air conditioner

12 V power terminal board

Stop valve for transport and reassembly

Auto-lubrication system (Lincoln) for front-

attachment pins, swing bearing, and center joint.

Fast-filling drop down panel with Wiggins coupler

for fuel, engine oil, engine coolant, grease,

pump transmission oil, and swing device oil.

O P T IONA L E Q U I P M E N T

High brightness working lights

Back and right side cameras with color monitor

Travel motor guard

Travel device guard

Electric oil pump to draw hydraulic oil from suc-

tion and return pipe lines

EX3600 -6 DIMENSIONS

EX3600 -6 SPECIFICATIONSE N G I N E

Make CumminsModel QSK60-C

Type 4 cycle

Aspiration Turbocharged and after cooled, direct injection chamber-type diesel engine

Net Power @ 1800 rpm (DIN 6271) 1,968 ps (1 450 kW)

Net Power @ 1800 rpm (SAE J1349) 1,944 hp (1 450 kW)

Gross Power @ 1800 rpm (SAE J1995) 1,944 hp (1,450 kW)

Maximum Torque @ 1500 rpm 6,156 lbf-ft (8 346 N-m)

Bore & Stroke 6.3 in. x 7.5 in. (159 x 190 mm)

Displacement 3,741 cu. in. (60.4 liters)

Batteries 4 x 12 V, 4 x 220 AH

Starting 24-volt electric

Cold Starting Ether aided

H Y D R A U L I C S Y S T E M

Hitachi’s Electronic Total Control System (ETS) achieves maximum efficiency, productivity, and operator comfort through reduced fuel consumption, lower noise levels, optimized engine-pump functions, and excellent controllability.

Engine-Pump Control (E-P)Main pumps are regulated by electronic engine-speed sensing control system.

Optimum Hydraulic SystemFour tandem-axial piston pump groups (eight pumps in total), supply a four-valve hydraulic system enabling both independent and combined operations of all functions.

Additional FeaturesFuel-Saving Pump (FPS) system

Auto-idling system

Hydraulic-drive cooling-fan system for oil cooler

Forced-lubrication and forced-cooling pump drive system

Main PumpsEight variable-displacement, piston pumps in four tandem-axial pump groups for front attachment, travel, and swing functions.

Pressure setting 4,270 psi (300 kgf/cm²) (29.4 MPa)

Max. oil flow 8 x 132.1 gal/min (8 x 500 L/min)

Pilot PumpGear pump

Pressure setting 640 psi (4.4 MPa) (45 kgf/cm²)

Maximum oil flow 29.0 gal/min (110 L/min)

Relief Valve SettingsImplement circuit 4,270 psi (300 kgf/cm2) (29.4 MPa)

Swing circuit 4,270 psi (300 kgf/cm2) (29.4 MPa)

Travel circuit 4,270 psi (300 kgf/cm2) (29.4 MPa)

Pilot circuit 640 psi (450 kgf/cm2) (4.4 MPa)

Hydraulic CylindersHigh-strength piston rods and tubes. Cylinder cushion mechanisms are provided for boom, arm, bucket and dump cylinders. Bucket cylinder of loading shovel is provided with protector.

Cylinder Dimensions (Backhoe) Cylinder Dimensions (Loading Shovel)Quantity Bore Rod Diameter Quantity Bore Rod Diameter

Boom 2 14.2 in. (360 mm) 10.2 in. (260 mm) Boom 2 14.2 in. (360 mm) 10.2 in. (260 mm)

Arm 2 11.8 in. (300 mm) 8.7 in. (220 mm) Arm 1 11.8 in. (300 mm) 8.7 in. (220 mm)

Level 1 14.2 in. (360 mm) 10.2 in. (260 mm)

Bucket 2 9.8 in. (250 mm) 7.1 in. (180 mm) Bucket 2 11.0 in. (280 mm) 7.9 in. (200 mm)

Dump 2 8.9 in. (225 mm) 5.1 in. (130 mm) Hydraulic FiltersAll hydraulic circuits have high-quality hydraulic filters for protection against oil contamination and longer life of hydraulic components. Filters are centralized for convenient maintenance.

QuantityFull flow filter 5 10 µm

High pressure strainer (In main & swing pump delivery line) 8 80 meshes

Drain filter (For all plunger type pumps & motors) 1 10 µm

Pilot filter 1 10 µm

By-pass filter (In oil cooler by-pass line) 1 5 µm

C ON T R OL S

Two Implement LeversWrist control type electric lever. Right lever is for boom and bucket control, left lever for swing and arm control.

For loading shovel, two pedals provided for opening/closing the bottom dump bucket.

Two Travel Levers with PedalsRemote-controlled hydraulic servo system. Independent drive at each track allows counter rotation of tracks.

U P P E R S T R U C T U R E

Revolving FrameDeep, full-reinforced box section. Heavy-gauge steel plates used for ruggedness.

Deck MachineryDeck machinery is positioned for maximum maintenance accessibility. Sidewalks provide easy access to engines, hydraulic and electrical components.

ISO-compliant stairs and handrails. Sidewalks and stairs are provided with skid-resistant plates.

S W I N G M E C H A N I S M

Four high-torque, axial-piston motors with two-stage planetary reduction gear bathed in oil. Swing circle with dirt seals is a heavy-duty, triple-row,

cylindrical roller bearing. Induction-hardened internal swing circle gear and pinion immersed in lubricant. Swing parking brake is spring-set, hydraulic

released disc type. This parking brake is manually releasable.

Swing Speed 3.2 min-1 (rpm)

O P E R AT O R ’ S C A b

The sturdy cab, with the top guard conforming to OPG Level II (ISO), protects the operator from falling objects. Independent, pressurized, 1 800 mm

wide, 2 150 mm high, roomy 7.5m³ cab with tinted-glass windows features all-round visibility. Spring-suspension type, fully adjustable reclining seat

with arm rests; movable with or without front & swing control levers by slide. Instrument and control panel are built in cab wall in easy range of the

operator. Three air conditioner system.

Noise level 76 dB (A) in the cab at maximum engine speed under no-load condition.

Eye level height 22 ft. 2 in. (6 760 mm)

U N DE R C A R R I AGE

TracksShovel-type undercarriage. Dual-flanged-type bolt linkage for side frame and X-form center frame assures durability. Heavy-duty track frame of

all-welded, stress-relieved structure. Top-grade materials used for toughness. Lifetime-lubricated induction-hardened track rollers, idlers and drive

tumblers with floating seals. Specially heat-treated connection pins. Hydraulic track adjuster provided with N2 gas accumulator with relief valve.

Track adjuster provided with protection device against abnormal tension. Travel motion alarm device.

Shovel-Type UndercarriageTriple grouser track shoes of induction-hardened cast steel

Shoe Width 50 in. (1 270 mm)

Number of Rollers and Shoes (each side)Upper Rollers 3

Lower Rollers 8

Track Shoes 38

Traction DeviceEach track driven by high-torque, axial piston motors, allowing counter rotation of tracks. two-stage planetary gear plus spur gears reduction device.

Dual-support-type traction device. Parking brake of spring-set/hydraulic-released disc type. This parking brake is manually releasable.

Travel Speeds Low: 1.5 mph (2.2 km/h)

High: 1.0 mph (1.7 km/h)

Max. Traction Force 395,700 lbf (179 500 kgf)

Gradability 30° (60%) continuous

W E I G H T S A N D G R O U N D P R E S S U R E

Loading Shovel: Equipped with 27.5 yd³ (21.0 m³) (SAE heaped) bottom dump bucket.

Shoe Type Shoe Width Operating Weight Ground Pressure

Triple Grousers 50 in. (1 270 mm) 795,900 lb. (361 000 kg) 27.4 psi (189 kPa) (1.93 kgf/cm³)

Backhoe: Equipped with 31 ft. 6 in. (9.6 m) BE-boom, 14 ft. 9 in. (4.5 m) BE-arm, and 29.0 yd³ (22.0 m³) (SAE heaped) bucket

Shoe Type Shoe Width Operating Weight Ground Pressure

Triple Grousers 50 in. (1 270 mm) 791,500 lb. (359 000 kg) 27.3 psi (188 kPa) (1.92 kgf/cm²)

EX3600 -6 SPECIFICATIONS

1 8

9

2 7

5

63

4

1. Left Console

2. Left Control Lever/Horn Switch

3. Left Travel Pedal

4. Left Travel Lever

5. Right Travel Lever

6. Right Travel Pedal

7. Right Control Lever/Horn Switch

8. Right Console

9. Operator's Seat

10. Bucket Close Pedal (For Loading Shovel)

11. Bucket Open Pedal (For Loading Shovel)

12. Pilot Control Shut-Off Lever

13. Rear Console

14. Emergency Engine Stop Switch

15. Engine Speed Control Dial

16. Key Switch

17. Monitor Display

bACKHOE CONTR OL L AYOUT

1. Engine

2. Engine Radiator3. LTA Radiator

4. Fan Motor x 45. Air Filter x 4

6. Hydraulic Pump x 87. High-Pressure Strainer x 8

8. Battery Unit

9. Engine-Pump Bulkhead

10. Muffler

11. Swing Device x 4

12. Control Valve x 4

13. Center Joint

14. Hydraulic Oil Tank

15. Fuel Tank

16. Hydraulic Oil Cooler x 4

17. Hydraulic Oil Cooling Fan Motor x 2

18. Lubricator

19. Cab

20. Folding Stairs

21. Ladder

22. Reserve Tank (Engine Oil)

23. Pump Mission Oil Cooler

24. Fuel Cooler

25. Reserve Tank (Coolant)

26. Engine-Radiator Bulkhead

4

5

68

7

1

23

9

DECK M ACHINERY L AYOUT

SERV ICE REFI LL CA PACITIES US Gallons Liters Imperial Gallons

Fuel Tank 1,968 7 450 1,639

Engine Coolant 162 614 135

Engine Oil (Engine Oil Pan) 69 261 57

Engine Oil (Reserve Tank) 75 284 62

Pump Drive 14 52 11.4

Swing Device (each side) 4 x 20 4 x 75 4 x 16.5

Travel Final Device (each side) 2 x 58 2 x 220 2 x 48.4

Hydraulic Tank 1,057 4 000 880

Hydraulic System 502 1 900 418

L OA DI N G S H OV E L AT TAC H M E N T

Boom and arm are of all-welded, low-stress, high-tensile strength steel full-box section design. Efficient, automatic level crowing achieved by one-lever control because parallel link mechanism keeps the bucket digging angle

constant, and level cylinder circuit maintains the bucket height constant (Auto-Leveling Crowd Mechanism).

Boom and arm are all-welded, low-stress, high-tensile strength steel full-box section design. Efficient, automatic level crowding achieved by one-lever control because parallel link mechanism keeps the bucket digging angle

constant, and level cylinder circuit maintains the bucket height constant (Auto-Leveling Crowd Mechanism).

Dual-support-type boom/arm/bucket pin linkage

Pin seals (in all portions) plus O-ring at arm top

All cylinders are provided with a cylinder cushion mechanism

Bucket cylinders with loading shovel are provided with an internal cylinder rod protector

EX3600 -6 SPECIFICATIONS

WORKING R ANGES—bUCKET CAPACIT Y: 27.5 yd³ (21.0 m³)

A. Min. digging distance 19 ft. 2 in. (5 850 mm)

B. Min. level crowding distance 29 ft. 1 in. (8 870 mm)

C. Level crowding distance 16 ft. 7 in. (5 050 mm)

D. Max. digging reach 49 ft. 11 in. (15 220 mm)

E. Max. cutting height 53 ft. 6 in. (16 300 mm)

E1. Max. dumping height 36 ft. 1 in. (10 990 mm)

F. Max. digging depth 12 ft. 0 in. (3 910 mm)

G. Working radius at max. dumping height 28 ft. 5 in. (8 650 mm)

H. Max. bucket opening width 6 ft. 5 in. (1 950 mm)

Arm crowding force 269,800 lb. (122 000 kgf) (1 200 kN)

Breakout force 254,000 lb. (115 000 kgf) (1 130 kN)

bUCKET (SAE HEAPED 2:1)

Capacity Width Number of Teeth Weight Type Materials Density27.5 yd³ (21.0 m³) 13 ft. 8 in. (4 160 mm) 6 59,300 lb. (26 900 kg) Bottom dump type, general purpose 3,033 lb./yd³ (1 800 kg/m³)

30.0 yd³ (23.0 m³) 13 ft. 8 in. (4 160 mm) 6 60,190 lb. (27 300 kg) Bottom dump type, general purpose 2,700 lb./yd³ (1 600 kg/m³)

Note: These buckets do not include any type of wear protection for sides, bottom, and inside the bucket. Please consult your local Hitachi dealer for a proper wear protection system for your application.

Please do not use the buckets without proper wear protection for your application.

b AC K H O E AT TAC H M E N T

Boom and arm are all-welded, low stress, full-box section design. Bucket of all-welded high-strength steel structure. Bucket/arm joint pins are floating type.

Replaceable thrust plates are provided with bucket/arm point part. Auto-lubrication system for all pins is standard.

WORKING R ANGES

Boom Length 31 ft. 6 in. (9.6 m)Arm Length 14 ft. 9 in. (4.5 m)

A. Max. digging reach 59 ft. 8 in. (18 190 mm)

A1. Max. digging reach (on ground) 57 ft. 9 in. (17 600 mm)

B. Max. digging depth 28 ft. 2 in. (8 580 mm)

B1. Max. digging depth (8 ft. level) 27 ft. 10 in. (8 490 mm)

C. Max. cutting height 58 ft. 1 in. (17 690 mm)

D. Max. dumping height 38 ft. 0 in. (11 590 mm)

E. Max. vertical wall depth 13 ft. 4 in. (4 060 mm)

Bucket Digging ForceSAE 209,500 lb. (932 kN)

ISO 236,000 lb. (1 050 kN)

Arm Crowd Force SAE 207,300 lb. (922 kN)

ISO 213,800 lb. (952 kN)

bUCKET

Capacity Width Number of Teeth

Weight Type Materials DensitySAE Heaped (1:1) Without Side Cutters

29.0 yd.³ (22.0 m³) 12 ft. 5 in. (3 790 mm) 6 40,570 lb. (18 400 kg) General purpose bucket 3,033 lb./yd³ (1 800 kg/m³)

Note: These buckets do not include any type of wear protection for sides, bottom, and inside the bucket. Please consult your local Hitachi dealer for a proper wear protection system for your application.

Please do not use the buckets without proper wear protection for your application.

UPPERSTRUCT URE

EX3600 -6 SHIPPING INF ORM ATIONEX3600-6 components are designed for ease of transportation and on-site assembly.

Components can be assembled without welding.

UNDERCA RRI AGE

Bucket Capacity A B Max. Width Weightft. in. (mm) ft. in. (mm) ft. in. (mm) lb. (kg)

27.5 yd³ (21.0 m³) 12 ft. 9 in. (3 890 mm) 11 ft. 9 in. (3 570 mm) 13 ft. 8 in. (4 160 mm) 59,300 lb. (26 900 mm)

30.0 yd³ (23.0 m³) 13 ft. 9 in. (4 190 mm) 11 ft. 10 in. (3 600 mm) 13 ft. 8 in. (4 160 mm) 60,190 lb. (27 300 mm)

L OA DING SHOV EL AT TACHMENT S

bACKHOE AT TACHMENT S

LIFTING CA PACITIES

R ATING OV ER SIDE OR 360 -DEGREES R ATING OV ER FRONT

ConditionsLoad Point

Height

LOAD R ADIUSAt Maximum Reach

26 ft. 3 in. (8 m) 32 ft. 10 in. (10 m) 39 ft. 4 in. (12 m) 45 ft. 11 in. (14 m) 49 ft. 3 in. (15 m) 52 ft. 6 in. (16 m)

ft. in. (meter)

BE-boom: 31 ft. 6 in. (9.6 m)BE-arm: 14 ft. 9 in. (4.5 m)Bucket SAE: 28.5 yd³ (22.0 m³)

42 ft. 8 in. (13 m)

*65.0 *65.0 *44.0 *44.0 34 ft. 10 in.

(*29.5) (*29.5) (*15.4) (*15.4) (15.8 m)

39 ft. 4 in. (12 m)

*68.3 *68.3 *32.9 *32.9 35 ft. 11 in.(*31.0) (*31.0) (*14.9) (*14.9) (16.3 m)

32 ft. 10 in. (10 m)

*65.7 *65.7 *61.7 *61.7 *31.8 *31.8 37 ft. 8 in.

(*29.8) (*29.8) (*28.0) (*28.0) (*14.4) (*14.4) (17.1 m)

26 ft. 3 in. (8 m)

*69.2 *69.2 *70.3 *70.3 *60.0 *60.0 *32.0 *32.0 38 ft. 10 in.

(*31.4) (*31.4) (*31.9) (*31.9) (*27.2) (*27.2) (*14.5) (*14.5) (17.6 m)

19 ft. 8 in. (6 m)

*97.9 *97.9 *87.1 *87.1 *80.5 *80.5 *72.3 *72.3 *33.1 *33.1 39 ft. 0 in.

(*44.4) (*44.4) (*39.5) (*39.5) (*36.5) (*36.5) (*32.8) (*32.8) (*15.0) (*15.0) (17.7 m)

13 ft. 1 in. (4 m)

*175.5 *175.5 *130.1 *130.1 *96.3 *97.7 83.1 *84.0 *58.4 *58.4 *35.5 *35.5 38 ft. 7 in.

(*79.6) (*79.6) (*59.0) (*59.0) (*43.7) (*44.3) (37.7) (*38.1) (*26.5) (*26.5) (*16.1) (*16.1) (17.5 m)

6 ft. 7 in. (2 m)

168.9 178.1 122.6 *136.9 91.7 *107.8 79.6 *95.5 *60.9 *60.9 *39.2 *39.2 37 ft. 8 in.

(76.6) (80.8) (55.6) (*62.1) (41.6) (*48.9) (36.1) (*43.3) (*27.6) (*27.6) (*17.8) (*17.8) (17.1 m)

0 (Ground)162.9 168.7 117.7 *131.2 88.4 *105.8 77.4 *87.3 *40.8 *40.8 35 ft. 11 in.

(73.9) (76.5) (53.4) (*59.5) (40.1) (*46.0) (35.1) (*39.6) (*18.5) (*18.5) (16.3 m)

-6 ft. 7 in. (-2 m)

*138.5 *138.5 *147.5 *147.5 115.7 *116.0 *86.0 *86.0 *67.9 *67.9

(*62.8) (*62.8) (*66.9) (*66.9) (52.5) (*52.6) (*39.0) (*39.0) (*30.8) (*30.8)

-13 ft. 1 in. (-4 m)

*128.1 *128.1 *113.5 *113.5 *88.2 *88.2 *52.5 *52.5

(*58.1) (*58.1) (*51.5) (*51.5) (*40.0) (*40.0) (*23.8) (*23.8)

-16 ft. 5 in. (-5 m)

*99.4 *99.4 *90.4 *90.4 *66.8 *66.8

(*45.1) (*45.1) (*41.0) (*41.0) (*30.3) (*30.3)

Notes: 1. Ratings are based on SAE J1097.

2. Lifting capacity of the EX Series does not exceed 75% of tipping load with the machine on firm, level ground or 87% full hydraulic capacity.

3. The load point is a hook (not standard equipment) loaded on the back of the bucket.

4. *Indicates load limited by hydraulic capacity.

UNIT 1 ,000 Lb. (1000 KG)

It’s our color. It’s our brand. New product-support initiatives and our

strengthened dealer network is more proof that we are as passionate as

ever about this industry. We are dedicated to building the best equipment

in the world and keeping it painted Hitachi Orange.

DKAEX3600HT Litho in U.S.A. (08-04)

OUR NA ME L OOKS GOOD ON OR A NGE.

www.hitachimining.com Specifications and design subject to change without notice.