This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
EVALUATION SCHEME
B.Tech Electronics & Instrumentation Engineering, B.Tech Instrumentation & Control
Measurement of level, Float type gauge, purge method, differential
pressure method, conductive and capacitive method; electromechanical method.
8
IV
Temperature measurements:
Standards and calibration, thermal expansion methods, bimetallic thermometer,
thermocouple, reference junction considerations, special materials,
configuration & techniques, Measurement of thermocouple output, Electrical
resistance sensors and thermistors, Radiation thermometers.
7
V
Miscellaneous Measurements: Viscosity, Density and Vacuum:
Measurement of Viscosity: Definitions, units, Newtonian and Newtonian
behaviour, measurement of viscosity using laboratory viscometers, industrial
viscometers. Viscometer selection and application.
Measurement of Density: Definitions, units, liquid density measurement,
gas densitometers, its application and selection.
Measurement of Vacuum: Mcleod gauge, Pirani gauge, Knudsen gauge and
Ionization gauge
8
COURSE OUTCOMES:
C304.1 Student will come to know about the basic concept of Measuring Instruments.
C304.2 Student will come to know about different transducers like pressure, temperature, displacement, force and
density.
C304.3 Student will come to know about the role of transducers and sensors in different applications.
C304.4 Student will be able to analyze the different characteristics of instruments.
C304.5 This subject is the backbone of instrumentation engineering and thus creates a platform for students over which
they can shape their ideas.
Text Books: 1. E. O. Doebelin, “Measurements systems: Applications and Design”, 4th Edition, Tata
McGraw Hill.
2. B. C. Nakra and K. K. Chaudhry, “Instrumentation: Measurements & Analysis” Tata
McGraw Hill
Reference Books: 1. A. K. Sawhney, “A Course in Electrical and Electronic Measurements and
Instrumentation” Dhanpat Rai Publications., 19th Edition.
2. Bela G. Liptak, "Process Measurement and Analysis, Vol. 1”, CRC Press.
REC-501 INTEGRATED CIRCUITS
Unit Topic Lectures
I
Analog Integrated circuit Design:an overview: Current Mirrors using BJT and MOSFETs, Simple current Mirror, Base current compensated current Mirror, Wilson and Improved Wilson Current Mirrors, Widlar Current source and Cascode current Mirror The 741 IC Op-Amp: Bias circuit, short circuit protection circuitry, the input stage, the second stage, the output stage, and device parameters; DC
Analysis of 741: Small Signal Analysis of input stage, the second stage, the
output stage; Gain, Frequency Response of 741; a Simplified Model, Slew
Rate, Relationship Between ft and SR
10
II
Linear Applications of IC op-amps: An Overview of Op-Amp (ideal and non-ideal) based Circuits V-I and I-V converters, generalized Impedance converter, simulation of inductors.
Filters: Ist and IInd order LP, HP, BP BS and All pass active filters, KHN.
8
III
Digital Integrated Circuit Design-An Overview: CMOS Logic Gate
Circuits: Basic Structure CMOS realization of Inverters, AND, OR, NAND
and NOR Gates
Latches and Flip flops: The Latch, The SR Flip-flop, CMOS
Implementation of SR Flip- flops, A Simpler CMOS Implementation of the
Clocked SR Flip-flop, D Flip-flop Circuits.
8
IV
Non-Linear applications of IC Op-amps: Log– Anti Log Amplifiers,
Precision Rectifiers, Peak Detectors, Simple and Hold Circuits, Analog
Multipliers and their applications. Op- amp as a comparator, Zero crossing
detector, Schmitt Trigger, Astable multi vibrator, Mono stable multi vibrator,
Generation of Triangular Waveforms
7
V
D/A and A/D converters Integrated Circuit Timer: The 555 Circuit,
Implementing a Monostable Multivibrator Using the 555 IC, Astable Multi
vibrator Using the 555 IC. Phase locked loops (PLL): Ex-OR Gates and multipliers as phase detectors,
Block Diagram of IC PLL, Working of PLL and Applications of PLL.
7
COURSE OUTCOMES:
Text Books:
1. Sedra and Smith, “Microelectronic Circuits”, 6thEdition, Oxford University Press. 2. Michael Jacob, “Applications and Design with Analog Integrated Circuits”, PHI,
2nd Edition.
Reference Books: 1. Jacob Millman and Arvin Grabel, “Microelectronics”, 2nd Edition, Tata McGraw Hill.
C305.1 Students will be able to gain in-depth knowledge of analog IC design and a complete analysis of 741-IC Op-
Amp. C305.2 Students will acquire knowledge about Op-Amp based circuits and basic components of ICs such as various
types of filters.
C305.3 Students will learn about CMOS digital integrated circuits and digital memory circuits.
C305.4 Students will be able to understand the concept of Op-Amp based non-linear and wave-shaping circuits.
C305.5 Students will gain knowledge about the working principle of data converters along with application specific
ICs such as 555 timer and PLL.
2. Behzad Razavi, “Fundamentals of Microelectronics”, 2nd Edition, Wiley. 3. Mark N. Horenstein, “Microelectronic Circuits and Devices”, PHI.
4. Paul R. Gray, Paul J. Hurst, Stephen H. Lewis and Robert G. Meyer, “Analysis and
Design of Analog Integrated Circuits”, Wiley. 5. Data Sheet: http://www.ti.com/lit/ds/symlink/tl082.pdf
1. John G Prokias, Dimitris G Manolakis, .Digital Signal Processing. Pearson Education.
2. Oppenheim & Schafer, . Digital Signal Processing. PHI
LABORATORY
RIC-551 MEASURING INSTRUMENTS LAB
List of Experiments:
1. 1.Characteristics of resistance transducer (i) Potentiometer (ii) StrainGauge
2. 2.Characteristics of LVDT.
3. Characteristics of capacitive transducer (i) Variable area (ii) Variable distance.
4. Characteristics of Thermistors
5. Characteristics of RTD.
6. Characteristics of Thermocouples
7. Characteristics of LDR, PhotoDiode, and Phototransistor: (i) Variable Illumination. (ii)
Linear Displacement.
8. Measurement of resistance by Wheatstone bridge and measurement of bridge sensitivity.
9. Measurement of Capacitance by De’Sautys and Schering Bridge.
10. Measure of low resistance by Kelvin’s double bridge.
11. Characteristics of diaphragm m type pressure transducer.
12. Characteristics of one Solid State sensor/Fiber optic sensor.
13. Project based on SENSOR ( Hardware)
COURSE OUTCOMES:
C311.1 Students will learn about the transducer related to measurement of physical quantity temperature i.e. RTD,
Thermocouple, Thermistor.
C311.2 Students will learn about the different passive transducer like Potentiometer, Strain gauge.
C311.3 Students will learn about the different active transducer like Photovoltaic cell.
C311.4 Students will gain the knowledge of different sensor like Solid state sensor or Fiber optic sensor.
C311.5 Students will learn about different AC Bridges like De’Sauty & Scheringe Bridge.
REC 551 INTEGRATED CIRCUITS LAB
Objective: - To design and implement the circuits to gain knowledge on performance of the
circuit and its application. These circuits should also be simulated on Pspice and implemented using TL082, LM741, NE555, ASLK, MPY634 KP connecting wires, Power Supply, function generator and oscilloscope.
1. Design and test a function generator that can generate square wave and triangular wave
output for a given frequency and cascade a multiplier MPY634KP in feedback loop to form VCO
2. Voltage to current and current to voltage convertors. 3. Second order filters using operational amplifier in universal active filter topology for –
a. Low pass filter of specified cutoff frequency b. High pass filter of specified frequency
c. Band pass filter with unit gain of specified pass band
d. Design a notch filter to eliminate 50Hz power line frequency 4. Wien bridge oscillator using operational amplifier. 5. Astable and monostable multivibrator using IC 555. 6. Design the following amplifiers:
a. A unity gain amplifier
b. A non-inverting amplifier with a gain of ‟A‟
c. An inverting amplifier with a gain of „A‟
d. Log and antilog amplifiers.
e. Voltage comparator and zero crossing detectors. 7. Design and test a PLL to get locked to a given frequency „f‟. Measure the locking range of
the system and also measure the change in phase of the output signal as input frequency is varied within the lock range.
8. Design and test the integrator for a given time constant. 9. Design and test a high-Q Band pass self-tuned filter for a given center frequency. 10. Design and test an AGC system for a given peak amplitude of sine-wave output. 11. Design and test a Low Dropout regulator using op-amps for a given voltage regulation
characteristic and compare the characteristics with TPS7250IC. 12. Design of a switched mode power supply that can provide a regulated output voltage for a
given input range using the TPS40200 IC
Note: All listed experiments are compulsory. In addition to it, the Institutes may include more experiments based on the expertise.
COURSE OUTCOMES:
C312.1 Student will learn about wave shaping circuits to generate different types of waveforms and will be
able to perform voltage to current, current to voltage conversion.
C312.2 Students will be able to analyze and design different non-linear applications of operational amplifiers
such as filters and oscillator etc.
C312.3 Students will be able to design astable and monostable multivibrator using 555 timer IC.
C312.4 Student will understand about operational amplifier analog IC-741and will be able to analyze and
design different linear applications of operational amplifiers such as
integrator, log, antilog amplifiers and voltage comparators. C312.5 Students will learn to determine capture range, lock in range and free running frequency of PLL and
will be able to understand and design voltage regulation methods.
REC-553 DIGITAL SIGNAL PROCESSING LAB
List of Experiments
1. To study about DSP Processors and architecture of TMS320C6713 DSP processor.
2. Introduction to Matlab and Code Composer Studio.
3. Write a Matlab Program for the generation of basic signals such as unit impulse, unit
step, ramp, exponential, sinusoidal and cosine.
4. To study matrix multiplication using code composer studio.
5. Evaluate 4 point DFT of and IDFT of x(n) = 1, 0 ≤ n ≤ 3; 0 elsewhere.
6. To implement FFT algorithm.
7. Verify Blackman and Hamming windowing techniques.
8. Implement IIR Butterworth analog Low Pass for a 4 KHz cut off frequency.
9. Verify Circular Convolution using code composer studio.
10. Verify Linear convolution of two sequence using code composer studio.
11. To implement Tone Generation.
12. To implement floating point arithmetic.
COURSE OUTCOMES:
CO313.1 Learn to apply the linear systems approach to signal processing problems using Matlab and Code
Composer Studio.
CO313.2 Students will be able to generate and analyze various types of signals and operations used in the
signal processing.
CO313.3 Students will be able to perform frequency domain analysis of discrete time systems using N- point
DFT and FFT.
CO313.4 Students will be able to design and evaluate the performance of FIR and IIR filters using window
techniques and Butterworth approximation respectively.
CO313.5 Students will be able to understand the concept of circular convolution and linear convolution.
RIC 554 SEMINAR
COURSE OUTCOMES:
CO314.1 Students will be able to demonstrate their technical, verbal and overall communication skills.
CO314.2 Students will be able to correlate the selection of topic with the latest trends in the technological
sector.
CO314.3 Students will be able to put their views and develop a problem solving approach
CO314.4 Students will develop self-confidence and enhance their presentation skills
CO314.5 Students will be motivated for lifelong learning
DEPARTMENTAL ELECTIVE COURSE- 1
RIC 011 FLUID MECHANICS
Unit Topic Lectures
I Introduction: Fluids and continuum: Physical properties of fluids, ideal and 8 rearfluids, Newtonian and non-Newtonian fluids, measurement of surface
tension. Kinematics of Fluid Flow: Steady and unsteady, uniform
and non-uniform, laminar and turbulent flows, one, two and three
dimensional flows, streamlines, streak lines and path lines,
II Fluid statics: Pressure-density-height relationship, manometers, pressure 8 on plane and curved surfaces, centre of pressure, buoyancy, stability of
immersed and floating bodies. Dynamics of Fluid flow: Euler's
equation of motion along a streamline and its integration, Bernoulli's
III Laminar and Turbulent Flow: Equation of motion for laminar flow 8
through pipes, Stoke's law, flow between parallel plates, flow through
porous media, fluidization, measurement of viscosity, transition from
laminar to turbulent low, turbulent flow, equation for turbulent flow,
eddy viscosity, mixing length concept and velocity distribution in
turbulent flow, Hot-wire anemometer and LDA.
IV Dimensional Analysis and Hydraulic Similitude: Dimensional 8
analysis, Buckingham's theorem, important dimensionless
numbers and their significance, geometric, Kinematic and dynamic
similarity, model studies. Pipe Flow: Nature of turbulent flow in pipes,
equation for velocity distribution Over smooth and rough surfaces,
resistance coefficient and its variation, flow in sudden expansion,
contraction, diffusers, bends, valves and siphons, concept of Equivalent
length, branched pipes, pipes in series and parallel, simple networks.
Compressibility Effects in pipe flow
COURSE OUTCOMES:
C307.1 Students will learn the concepts of fluid mechanics to develop machine working on fluid energy.
C307.2 Students will be able to develop machines and pumps of higher efficiency using the concept of fluid
mechanics.
C307.3 Students will be able to verify experimental results by validation through CFD (computational fluid
dynamics) for research purpose.
C307.4 Students will be comfortable in design of all the civil engineering structures dealing with fluid flow
like pipe-line, dam, canal etc.
Text Books:
1. Som and Biswas, "Introduction to fluid mechanics and machines", Tata McGraw Hill
Publication.
2. S.K.Agrawal, "Fluid mechanics and machinery", Tata McGraw Hill Publication.
REC/RIC 012 Computer Architecture and Organization
Unit Topic Lectures
I Introduction to Design Methodology: System Design - System 8 representation, Design Process, the gate level (revision), the register level
components and PLD (revision), register level design The Processor Level:
II Processor basics: CPU organization- Fundamentals, Additional features Data 8 Representation - Basic formats, Fixed point numbers, Floating point numbers.