EU DECLARATION OF CONFORMITY - Vaisala · Original Project ID: 3010615 Approval Granted: January 9, 2002 Subsequent Revision Reports / Date Approval Amended Report Number Date Report

2016-07-06A/JTL Page 1 (2)

Vaisala Oyj | PO Box 26, FI-00421 Helsinki, Finland Phone +358 9 894 91 | Fax +358 9 8949 2227 Email [email protected] | www.vaisala.com Domicile Vantaa, Finland | VAT FI01244162 | Business ID 0124416-2

EU DECLARATION OF CONFORMITY Manufacturer: Vaisala Oyj Post address: PL 26, FIN-00421 Helsinki Street address: Vanha Nurmijärventie 21, Vantaa, Finland

This declaration of conformity is issued under the sole responsibility of the manufacturer. Object of the declaration: HMT360 -series Intrinsically safe Humidity and Temperature transmitters The object of the declaration described above is in conformity with Directives:

ATEX Directive (2014/34/EU of 26 February 2014) EMC Directive (2014/30/EU of 26 February 2014) ROHS Directive (2011/65/EU of 8 June 2011)

The conformity is declared with using the following standards: EN 60079-0 (2012) EN 60079-11 (2012) EC-type examination certificate number: VTT 09 ATEX 028X issue No:3 EN 61326-1:2013 Electrical equipment for measurement, control and laboratory use -

EMC requirements - for use in industrial locations. EN 55022:2010 Class B. Information technology equipment - Radio disturbance

characteristics - Limits and methods of measurement.

EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances

Vantaa 2016-07-06

......................................................... Jukka Lyömiö Standards and Approvals Manager

2016-07-06A/JTL Page 2 (2)

HMT360 TRANSMITTER: DESCRIPTION

Transmitter unit: The HMT360 transmitters have independent transmitter body and probe units to be attached together. The HMP360 -series probes are used only with the HMT360 transmitter.

Probe types: HMT360 transmitter can be equipped with the following probe units, with different kinds of sensor heads and cable lengths 2m, 5m and 10m. The probe types covered by this D.O.C are: HMP361 - short probe for wall mounting HMT362 - small pressure-tight flanged probe HMP363 - small probe head (diameter 13.5 mm) for tight spaces HMP364 - probe for pressurized spaces up to 100 bar HMP365 - probe for high temperatures up to +180 °C HMP367 - probe for high humidities HMP368 - probe for installations in pressurized pipelines (up to 40 bars)

- End of list -

To verify the availability of the Approved product, please refer to www.approvalguide.com FM Approvals HLC 5/13 0003010615

Page 1 of 2

FM Approvals 1151 Boston Providence Turnpike P.O. Box 9102 Norwood, MA 02062 USA T: 781 762 4300 F: 781-762-9375 www.fmapprovals.com

CERTIFICATE OF COMPLIANCE HAZARDOUS (CLASSIFIED) LOCATION ELECTRICAL EQUIPMENT

This certificate is issued for the following equipment:

HMT360abcdefghi4jklAmn. Transmitter and Probe or Transmitter only. IS / I,II,III / 1 / ABCDEFG / T5 Ta = 60°C - DRW211603, Entity; NI / I, / 2 / ABCD / T5 Ta = 60°C; S / II,III / 2 / FG / T5 Ta = 60°C Entity Parameters:

VMax (V)

IMax (mA)

PMax (W)

Ci (nF)

Li (μH)

Terminals

Ch 1: + and - 28 100 0.7 1 0

Ch 2: + and - 28 100 0.7 1 0

a = Probe type: 0, 1, 2, 3, 4, 5, 7 or 8. b = Transmitter type: any single letter A-Z. c = Display: 1 or 2. d = Output channels: 1 or 2. e = Analog output signal (Ch1): any single letter A-Z. f = Analog output signal (Ch 2): any single letter A-Z. g = Output range: any single letter A-Z. h = Units: 1 or 2. i = Cable bushings: A, B, C or 4. j = Manual: Any single letter A-Z. k = Cable length: (any single letter) A-Z or 0, 1, 2 or 3. l = Humidity sensor: 0, 1, 2, 3, 4, 5, 6, 7 or A. m = Sensor protection: 0, 1, 2, 3, 4, 6 or 7. n = Installation kit: A-Z or 0.

To verify the availability of the Approved product, please refer to www.approvalguide.com FM Approvals HLC 5/13 0003010615

Page 2 of 2

Equipment Ratings: Intrinsically Safe Class I, II, III, Division 1, Groups A, B, C, D, E, F, & G; also as Class I, Zone 0, AEx ia IIC; in accordance with Entity requirements when installed per installation drawing DRW211603; and Nonincendive Class I, Division 2, Groups A, B, C, & D; Suitable for Class II & III, Division 2, Groups F & G, for use in an indoor hazardous (classified) locations with a temperature rating of T5, Ta = 60°C. FM Approved for:

Vaisala Oyj Helsinki, Finland This certifies that the equipment described has been found to comply with the following Approval Standards and other documents: Class 3600 2011 Class 3610 2010 Class 3611 2004 Class 3810 2005 Original Project ID: 3010615 Approval Granted: January 9, 2002

Subsequent Revision Reports / Date Approval Amended Report Number Date Report Number Date 3016167 March 14, 2003 3017701 August 7, 2003 030916 November 3, 2003 051221 May 24, 2006 091102 November 5, 2009 3048304 August 8, 2013 FM Approvals LLC

8 August 2013

J.E. Marquedant Group Manager, Electrical

Date

Certificate of ComplianceCertificate: 1300863 Master Contract: 213862

Project: 2759392 Date Issued: November 13, 2014

DQD 507 Rev. 2012-05-22 Page: 1

Issued to: Vaisala Oyj

P.O. Box 26Helsinki, 00421FinlandAttention: Jorma Lehtonen

The products listed below are eligible to bear the CSA Mark shown

Issued by: Zahra Amini

PRODUCTS

CLASS 2258 03 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non -Incendive Systems - For Hazardous Locations

Class I, Div.1 and Div.2, Groups A, B, C and D; Class II, Div.1 and Div.2, Groups G and Coal Dust; Class III

HMT 360 series, humidity and temperature transmitters, rated 28V, 4-20 mA, and provides intrinsically safeoutputs to HMP36* series probe when connected as per installation drawing DRW213478, Maximum ambienttemperature 60°C, Temperature Code T4.

APPLICABLE REQUIREMENTS

CSA Std C22.2 No. 142-M1987 - Process Control Equipment

CSA Std C22.2 No. 213-M1987 -Non-Incendive Electrical Equipment for Use in Class I, Division 2 HazardousLocations

CSA Std C22.2 No. 157-1992 -Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations

Certificate: 1300863 Master Contract: 213862

Project: 2759392 Date Issued: November 13, 2014

DQD 507 Rev. 2012-05-22 Page: 2

MARKINGS

- CSA Monogram

- Company name

- Model number

- Serial number

- Electrical ratings

- Exia Symbol

- Hazardous Location Designation

- Temperature Code T4 (135°C)

- Reference to installation drawing DRW213478

- Maximum Ambient Temperature (60°C)

- Statements re Intrinsically Safe

- Caution re. Substitution of components…

- Caution re. Do not disconnect ….

Replaced

by

Drawn

Review

Appr

Design

Replaces

Scale

id

Title

Arch

no

Serial Sheet

doc no

Cooperator`s

Dwg no Rev

Ltr Qty Change Reason/ ECO no Design Date Review Date Appr

NOTE:1. Each channel must be supplied through separateshielded cables.2. When using galvanic separators CH1- and CH2-must be short circuited with an external wire.3. When using transmitter in Class I, Division 2 themain switch shall not be operated or the unit shall notbe disconnected unless power has been switched off,or area is known to be non hazardous.4. Use only conduit connection in Division 2.5. Substitution on components may impair intrinsicsafety or suitability for Division 2.6. Only intrinsically safe installation is allowed in Class IIand Class III environments.7. Intrinsically safe barrier ground mustbe less than 1 ohm.8. Maximum safe area voltage is 250V.

Wiring diagram for intrinsically safe operation of the HMT360-series humidity

and temperature transmitter.

HMT360-series transmitters are approved for use inDivision 1 and 2, Class I, Groups A, B, C, and D.Division 1, and 2, Class II, Group G and coal dust.Division 1, and 2, Class III.

Vaisala OyjVanhanurmijärventie 21VantaaFinland

Installation

Drawing

DRW213478

HAZARDOUS AREA

SAFE AREA

HMT360 connection board

-Ch1+ -Ch2+

Load Ch2

Vmax=28VDC

Vmax=28VDC

Load Ch1

KKe 2002-08-21

HMT360-series transmitters shall be used withfollowing probes:Probe HMP361 with 127mm long pipe.Probe HMP362 with 2, 5 or 10 m length cableProbe HMP363 with 2, 5 or 10 m length cableProbe HMP364 with 2, 5 or 10 m length cableProbe HMP365 with 2, 5 or 10 m length cableProbe HMP367 with 2, 5 or 10 m length cableProbe HMP368 with 2, 5 or 10 m length cable

The material for associated cable is FEP(Tetrafluoropropylene) or for HMP363 also PUR(Polyurethane) available.

To avoid static discharge shall the cable cover withconductive material.

Vaisala offers following barrier and galvanic isolator types:

Manufacturer: Type: Vaisala code:

Barrier: R. Stahl 9001/51-280-091-141 210664Isolator: R. Stahl 9160/13-11-11 212483

If other barrier or galvanic isolator types are used,Vaisala or CSA do not take responsibility for the selectedbarrier's or galvanic isolator's suitability!

Cable parameters shall be less than 60pF/ft (197pF/m)and 0.2µH/ft (0.67µH/m). The maximum cable lengthis 2000ft (600m).

Max cable length 2000ft (600m)

C

IML 2002-10-06

KKe 2002-10-06

DRW213478B

C Probe types and barrier/isolator info updated ECO212844 KKe 2006-06-20 RHA 2006-06-20 HJJ