This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
TWCL-50 Clamp TW2500 Strap Standard Bender With Degree Scale
Flexel™ Type FLAFlexible Fittings
Type 4QSLiquidtight Connectors
Effective September, 2008Copyright 2008
PAGE 2
800-621-1506www.appletonelec.com
TW-1
TW
Effective September, 2008Copyright 2008
PAGE 2
Steel EMT Set-Screw Connectors and Couplings
4000S Series Connectors
Features • Heavy steel walls.
• Concretetight when taped.
• Pre-set/Pre-staked set screws.
• Male hub threads NPS.
• Available with insulated throat.
• Three-way combination screws.
• Insulated throat connector rated 90°C.
Standard Materials • Steel.
Standard Finish• Zinc Plated.
Third Party Certification• UL Listed: E-14815 (1/2” to 2”)
• UL Listed: E-14816 (2-1/2” to 4”)
Applicable Third Party Standards• UL 514B
• CSA Standard C22.2 No. 18
• NEMA FB-1
• Federal Spec. W-F-408E
Type 4050S — Type 4100S Type 4125S — Type 4400S
Type 5125S — Type 5400S
Insulated Trade Throat Dimensions in Inches Wt. Lbs. Ctn. Std. Size Catalog Catalog Body Max Thread Per 100 Qty. Pkg. (inches) Number Number Length Dia. Length
Third Party Certification• UL Listed: E-14815 (1/2” to 2”)
• UL Listed: E-14816 (2-1/2” to 4”)
• Listed Concretetight 1/2” through 4”.
Applicable Third Party Standards
• UL 514B
• CSA Standard C22.2 No. 18
• NEMA FB-1
• Federal Spec. W-F-408E
Trade Size Catalog Dimension in Inches Wt. Lbs. Ctn. Std.(Inches) Number Body Length Max. Dia. Per 100 Qty. Pkg.
1/2 6050S 1-3/8 27/32 19 25 250
3/4 6075S 1-1/2 1-3/8 25 20 200
1 6100S 1-21/32 1-5/16 39 20 100
1-1/4 6125S 2-1/2 1-11/16 88 5 25
1-1/2 6150S 2-1/2 1-15/16 104 5 25
2 6200S 2-1/2 2-3/8 149 2 10
2-1/2* 6250S 4-1/4 3-1/8 240 — 10
3* 6300S 4-1/2 3-3/4 350 — 5
3-1/2* 6350S 4-3/4 4-1/4 475 — 5
4* 6400S 5 4-3/4 600 — 5
Type 6050S — Type 6400S
7000S Series Connectors
Features • Male hub threads NPS.
• Available with insulated throat.
• Concretetight.
• Insulated throat connector rated 90°C.
Standard Materials • Steel Body and Nut.
Standard Finish• Zinc Plated
Third Party Certification• UL Listed: E-14815 (1/2” to 2”)
• UL Listed: E-14816 (2-1/2” to 4”)
• Listed Concretetight 1/2” through 4”.
Applicable Third Party Standards• UL 514B
• CSA Standard C22.2 No. 18
• NEMA FB-1
• Federal Spec. W-F-408E
All dimensions are approximate and subject to change.
Type 7050S — Type 7400S
Insulated Trade Throat Dimensions in Inches Wt. Lbs. Ctn. Std. Size Catalog Catalog Body Max Thread Per 100 Qty. Pkg. (inches) Number Number Length Dia. Length
InspectoRidge™Provides external visual inspection aid on outside surface, to assure raintight fittings are installed, without disassembly of conduit run.
UL Listed Raintight Steel EMT Compression Connectors and Couplings
Raintight Gland Compression Connector – 7000SR Series
Use:To ground and secure EMT raceway to boxes and enclosures in wet locations.
Features:• UL Listed Raintight
• InspectoRidgeª external visual inspection aid — See below
• No disassembly required
• Male hub threads NPS
• Available with and without insulated throat
• Concretetight
Material/Finish:• Steel Body & Nut Zinc Electroplated
• Silicone Rubber Internal Sealing Ring
• EPDM Rubber KO Sealing Ring
Raintight Gland Compression Coupling Type – 6000SR Series
Use:To ground and secure EMT raceway sections together in wet locations.Features:• UL Listed Raintight
• InspectoRidgeª external visual inspection aid — See below
• No disassembly required
• Concretetight
Material/Finish:• Steel Body & Nut Zinc Electroplated
• Silicone Rubber Internal Sealing Rings
Type 6050SR — Type 6200SR
Insulated Trade Throat Dimensions in Inches Wt. Lbs. Ctn. Std. Size Catalog Catalog Body Max Thread Per 100 Qty. Pkg. (inches) Number Number Length Dia. Length
Applicable Third Party Standards:• UL Standard: 514B
• NEMA: FB-1
• Federal Spec: W-F-408E
Effective September, 2008Copyright 2008
800-621-1506www.appletonelec.com
PAGE 7
TW-1TW
ETP Flexel® EMT Flexible Fitting
Type FLAFor EMT
Application• The Flexel Fitting is an innovative product in which to couple lengths of EMT together or connect EMT to a panel board, junction box, etc., when and where a change of direction is required in the conduit run.
Features• Easily hand-bendable from straight tubing to 90° or any angle in between. No need to waste time using cumbersome bending equipment.• Rigid enough to maintain configuration until manually re-formed. • Wire pulls through formed bends.• Specially designed so internal diameter remains unchanged, regardless of the bend configuration. • Maintains compliance with NEC's mini-mum radius requirements.• Can be bent to various degrees, including offset and compound angles.• Suitable for use indoors or dry locations wherever EMT is used as a raceway.• Safely conducts the maximum ground fault current required by UL, CSA and the National Electrical Code. No need to pull a separate grounding conductor. Standard Material/FinishFlexible Length: Strip Steel/GalvanizedEnd Fittings: Steel/Galvanized
Compliances UL Listed: E-14895
CSA Certified: LR9795
Applicable Third Party Standards:• UL Standard: 514B
• CSA Standard: C22.2 No. 18
Type FLA
Dimensions are approximate. Consult your local representative for details.
A
B
B
C
D
Dimensions in inches Trade A D Size Catalog Nominal C Max. (inches) Number Length B Radius Offset
11/4 FLA-125 24 141/2 73/4 41/2
11/2 FLA-150 29 143/4 93/4 61/2
2 FLA-200 26 161/4 131/4 41/4
21/2 FLA-250 29 22 16 21/2
3 FLA-300 36 22 17 33/4
31/2 FLA-350 38 22 18 3 4 FLA-400 40 261/2 19 11
Effective September, 2008Copyright 2008
PAGE 8
800-621-1506www.appletonelec.com
TW-1
TW
ETP Steel Liquidtight Fittings
Type 4QS45° and 90°
Application • 4QS liquidtight connectors and liquidtight flex-ible metallic conduit are used in applications where conditions of installation, operation or maintenance require flexibility or protection from liquids, vapors or solids such as: machine tool building, motor and transformer terminations, robotics assembly, air conditioning equipment installation and Class I, Division 2 wiring
Features• Tapered threaded male hub NPT
• Compact, slim diameter with small turning radius
• Furnished with locknut and sealing ring.
• Liquidtight/Raintight/Oiltight
• Suitable for grounding (through 1-1/4”)
• Suitable for wet locations
• Long ferrule prevents pullout and tight bend conduit “pop-out”
• Suitable for use in the following Hazardous Locations:
Class I, Div. 2 per NEC 501.4(B)Class I, Zone 2 per NEC 505.15(C)(2)Class II, Div. 2 per NEC 502.4(A)(1)(e)Class II, Div. 2 per NEC 502.4(B)(2)Class III, Div. 1 per NEC 503.3(A)(2)Class III, Div. 2 per NEC 503.3(B)Intrinsically Safe per NEC 504.20
• Bonding Locknuts are recommended in Haz-ardous Locations. See GL Series in Section CF-2, page 15.
Material/Finish:Straight: Steel/Zinc PlatedAngles: Body: Malleable Iron/Zinc Plated Gland nut, ferrule and locknut: Steel/Zinc PlatedThird Party Certification: UL Listed: 11853
CSA Certified: 9795
UL Listed liquidtight flexible metal conduit fit-tings from 3/8” through 1-1/4” trade sizes are suitable for grounding under NEC 250.118(7).Applicable Third Party Standards:UL Standard: 514BCSA Standard: C22.2 No. 18NEMA: FB-1Federal Spec: W-F-406E
45° Type 4QS-438 — Type 4QS-4200
90° Type 4QS-938 — Type 4QS-9200
Insulated Throat Trade Size Catalog Catalog Dimensions in Inches (inches) Number Number A B C