ESnet JUNOS/TiMOS Configurations for OSCARS Ethernet VLAN Circuit Services Using ISIS, LDP, and l2circuits Introduction This document is to provide a better understanding of the dataplane configuration that ESnet uses to provide OSCARS Ethernet VLAN circuit services on Juniper and Alcatel routers. The example topology (see Fig 1.) is made up of four connected routers (Juniper M10, MX80, MX960, and Alcatel (ALU) 7750c4) with connections between them consisting of 1GE and 10GE links. Figure 1. Topology Setup To clarify the configurations, three bidirectional circuits have been configured to connect the three endpoints (netlabpt4, netlabpt5, and netlabpt6) over different network paths, and different VLAN IDs for the service handoff. Protocol Requirements In ESnet, the following protocols are used to support this service.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ESnet JUNOS/TiMOS Configurations for OSCARS Ethernet VLAN Circuit Services Using IS-‐IS, LDP, and l2circuits
Introduction This document is to provide a better understanding of the dataplane configuration that ESnet uses to provide OSCARS Ethernet VLAN circuit services on Juniper and Alcatel routers. The example topology (see Fig 1.) is made up of four connected routers (Juniper M10, MX80, MX960, and Alcatel (ALU) 7750c4) with connections between them consisting of 1GE and 10GE links.
Figure 1. Topology Setup
To clarify the configurations, three bi-‐directional circuits have been configured to connect the three end-‐points (netlab-‐pt4, netlab-‐pt5, and netlab-‐pt6) over different network paths, and different VLAN IDs for the service handoff.
Protocol Requirements In ESnet, the following protocols are used to support this service.
Intermediate System to Intermediate System (IS-‐IS) ISIS is enabled to learn the connectivity/topology of the network. The traffic engineering (TE) function in IS-‐IS is enabled to facilitate CSPF (Constrained Shortest Path First) calculations to build MPLS LSPs. The following is the ISIS configuration on the dev-‐mx80-‐rt1. protocols { isis { export [ netlab-igpv4-routes reject-all ]; reference-bandwidth 1000g; topologies ipv6-unicast; ## traffic engineering is enabled by default level 2 { inactive: authentication-key "$9$WbEX7dji.fQnRh4ZGif5ylev7V"; ## SECRET-DATA inactive: authentication-type simple; wide-metrics-only; } level 1 disable; /* dev-mx960-rt1 */ interface xe-0/0/0.0 { point-to-point; level 2 metric 1000; } /* dev-m10-rt3 */ interface ge-1/0/0.0 { point-to-point; level 2 metric 1000; } interface lo0.0; } }
The following is the ISIS configuration on the dev-‐7750c4-‐rt1. #-------------------------------------------------- echo "ISIS Configuration" #-------------------------------------------------- isis level-capability level-2 area-id 49 export "netlab-igpv4-routes" traffic-engineering level 2 wide-metrics-only exit interface "system" exit interface "to_dev-mx960-rt1" level-capability level-2 interface-type point-to-point level 2 ipv6-unicast-metric 1000 metric 1000 exit exit exit
Multi-‐Protocol Label Switching (MPLS) MPLS is enabled to support label switching on the routers. The following is the MPLS configuration on dev-‐mx80-‐rt1. protocols { mpls { path-mtu { ## to support large MPLS packet MTU allow-fragmentation; rsvp mtu-signaling; } explicit-null; ## disables PHP to enforce LER-LER MPLS CoS /* dev-mx960-rt1 */ interface xe-0/0/0.0; /* dev-m10-rt3 */ interface ge-1/0/0.0; } }
The following is the MPLS configuration on dev-‐7750c4-‐rt1. #-------------------------------------------------- echo "MPLS Configuration" #-------------------------------------------------- mpls interface "system" exit interface "to_dev-mx960-rt1" exit exit
Resource Reservation Setup Protocol (RSVP) RSVP is enabled to support the signaling and provisioning on MPLS Label Switched Paths (LSPs). The following is the RSVP configuration on dev-‐mx80-‐rt1. protocols { rsvp { /* dev-mx960-rt1 */ interface xe-0/0/0.0; /* dev-m10-rt3 */ interface ge-1/0/0.0; } }
The following is the RSVP configuration on dev-‐7750c4-‐rt1. #-------------------------------------------------- echo "RSVP Configuration" #-------------------------------------------------- rsvp interface "system" exit interface "to_dev-mx960-rt1" exit no shutdown exit
Label Distribution Protocol (LDP) LDP is enabled to disseminate information necessary to setup the layer 2 circuit service between the head and tail PE routers. The following is the LDP configuration on dev-‐mx80-‐rt1. protocols { ldp { track-igp-metric; ## use IGP metrics for LDP routes /* dev-mx960-rt1 */ interface xe-0/0/0.0; /* dev-m10-rt3 */ interface ge-1/0/0.0; /* dev-mx80-rt1 */ interface lo0.0; } }
The following is the LDP configuration on dev-‐7750c4-‐rt1. #-------------------------------------------------- echo "LDP Configuration" #-------------------------------------------------- ldp interface-parameters interface "to_dev-mx960-rt1" exit exit targeted-session exit exit exit
Class of Service Requirements In ESnet, four classes of service are specified, i.e. Network-‐Control (NC), Expedited-‐Forwarding (EF), Best-‐Effort (BE), and Scavenger (SS). For the OSCARS service, ESnet only uses *two classes of service (i.e. EF and SS) on the Juniper routers, but only a singe class of service queue (i.e. EF) with priority tags on the ALUs. When an OSCARS bandwidth reservation is confirmed in ESnet, the user requested bandwidth is enforced as a “floor” guarantee, that is, the user is guaranteed to at least have the amount they requested in the reservation. To accomplish this, on the Juniper routers, conforming traffic (i.e. traffic up to the user specified rate) is classified to use the EF class. Non-‐conforming traffic (i.e. traffic above the user specified rate) is classified to use the SS class*. For example, if a user asks for a 500Mbps circuit and sends traffic at 900Mbps, the first 500Mbps will be classified into the EF class, and the remaining 400Mbps will be classified into the SS class. *NB: Using two class of service queues in this instance can cause out-‐of-‐order packets. On the ALU routers, all OSCARS circuit traffic is placed in the EF queue with the conforming traffic tagged as “in-‐profile”, and over-‐subscribed traffic tagged as “out-‐
of-‐profile”. The ALU gives precedence to “in-‐profile” packets up to the guaranteed bandwidth, and then transmits or drops “out-‐of-‐profile” packets based on the remaining available bandwidth. To ensure that the user receives their bandwidth guarantees, the OSCARS Path Computation Engine will calculate a viable that does not over-‐subscribe any of the individual links on that path. The following is the class-‐of-‐service configuration on dev-‐mx80-‐rt1. groups { sdn-cos-group { class-of-service { interfaces { <*> { scheduler-map esnet_sdn_scheduler; unit * { classifiers { dscp esnet_dscp_classifier; dscp-ipv6 esnet_dscp-ipv6_classifier; exp esnet_exp_classifier; } rewrite-rules { dscp esnet_dscp_rewrite-rules; dscp-ipv6 esnet_dscp-ipv6_rewrite-rules; exp esnet_exp_rewrite-rules; } } } } } } } class-of-service { classifiers { dscp esnet_dscp_classifier { /* Remapping of [ 001000 001010 001100 001110 101110 ] from default required */ import default; forwarding-class expedited-forwarding { /* ef(101110) */ loss-priority low code-points ef; } forwarding-class best-effort { /* af11(001010) af12(001100) af13(001110) */ loss-priority low code-points [ af11 af12 af13 ]; } forwarding-class scavenger { /* ss(001000) */ loss-priority high code-points ss; } } dscp-ipv6 esnet_dscp-ipv6_classifier { /* Remapping of [ 001000 001010 001100 001110 101110 ] from default required */ import default; forwarding-class expedited-forwarding { /* ef(101110) */ loss-priority low code-points ef; }
Circuit Setup When an OSCARS reservation is requested, there are several mandatory parameters required to construct the configuration for the Ethernet VLAN service circuit. They are; source (router, port, VLAN,), destination (router, port, VLAN), bandwidth, start time, and end time. Optionally, if the user is authorized, he/she can submit an Explicit Route Object (ERO) which dictates the path the circuit should take within the network. As reflected in Figure 1, there is a single multi-‐point Ethernet VLAN circuit service instantiated. The first request is an Ethernet VLAN service with different VLAN IDs (VLANS 3006, 3005) on both Provider Edge (PE) routers (dev-‐mx80-‐rt1 and dev-‐mx960-‐rt1), and an ERO specifying an intermediate hop (dev-‐m10-‐rt3). The second and third requests**, which uses the same reservation ID (“netlab-‐xxxx”) add a third PE router (7750c4-‐rt1) to cerate a fully connected service., and the second for identical VLAN IDs (VLAN 3056) with no ERO defined. **NB: Multiple request using the same reservation ID has not been implemented in OSCARS, but is used to show how a multipoint service might be constructed.
Global Reservation ID (GRI): netlab-‐xxxx Source urn:ogf:network:domain=netlab:node=dev-‐mx80-‐rt1:port=xe-‐0/0/1:link=* Src VLAN 3006 Dest urn:ogf:network:domain=netlab:node=dev-‐mx960-‐rt1:port=xe-‐11/2/0:link=* Dest VLAN 3005 Bandwidth 500Mbps Start Time 7/1/2012 00:00 End Time 7/13/2012 23:59 ERO urn:ogf:network:domain=netlab:node=dev-‐mx80-‐rt1:port=ge-‐1/0/0:link=ge-‐1/0/0.0
Dest urn:ogf:network:domain=netlab:node=dev-‐7750c4-‐rt1:port=1/5/2:link=* Dest VLAN 3004 Bandwidth 500Mbps Start Time 7/1/2012 00:00 End Time 7/13/2012 23:59 ERO Not Specified
Global Reservation ID (GRI): netlab-‐xxxx Src urn:ogf:network:domain=netlab:node=dev-‐mx960-‐rt1:port=xe-‐11/2/0:link=* Src VLAN 3005 Dest urn:ogf:network:domain=netlab:node=dev-‐7750c4-‐rt1:port=1/5/2:link=* Dest VLAN 3004 Bandwidth 500Mbps Start Time 7/1/2012 00:00 End Time 7/13/2012 23:59 ERO Not Specified
Circuit GRI netlab-‐xxxx Configurations The following is the circuit GRI netlab-‐xxxx configuration on dev-‐mx80-‐rt1. interfaces { xe-0/0/1 { flexible-vlan-tagging; mtu 9192; encapsulation flexible-ethernet-services; unit 3006 { description netlab-xxxx:500000000:oscars-vpls:show:circuit-intercloud; ## description is arbitrary encapsulation vlan-vpls; vlan-id 3006; output-vlan-map swap; family vpls { filter { input netlab-xxxx_stats; output netlab-xxxx_stats; } } } } } routing-options { forwarding-table { export [ netlab-xxxx ]; ## to instantiate policy netlab-xxxx indirect-next-hop; } } protocols { mpls { label-switched-path netlab-xxxx_to_dev-mx960-rt1 { from 10.96.0.4; to 10.32.0.62; ## LSP is built to egress router’s provider ## facing interface, not loopback metric 65535; bandwidth 500m; priority 4 4; primary netlab-xxxx_to_dev-mx960-rt1; policing filter netlab-xxxx_policing; ## enforce user b/w limits }
label-switched-path netlab-xxxx_to_dev-7750c4-rt1 { from 10.96.0.4; to 10.32.0.70; ## LSP is built to egress router’s provider ## facing interface, not loopback metric 65535; bandwidth 500m; priority 4 4; primary netlab-xxxx_to_dev-7750c4-rt1; policing filter netlab-xxxx_policing; } path netlab-xxxx_to_dev-mx960-rt1 { 10.32.0.17 strict; 10.32.0.62 strict; } path netlab-xxxx_to_dev-7750c4-rt1 { 10.32.0.14 strict; 10.32.0.70 strict; } } } policy-options { policy-statement netlab-xxxx { ## policy to tie route to LSP term netlab-xxxx { from community netlab-xxxx; then { install-nexthop lsp [ netlab-xxxx_to_dev-mx960-rt1 netlab-xxxx_to_dev-7750c4-rt1 ]; accept; } } } community netlab-xxxx members 65000:3006; } firewall { family vpls { filter netlab-xxxx_stats { ## for counting circuit in/out packets interface-specific; term netlab-xxxx_stats { then { count netlab-xxxx_stats; accept; } } } } family any { filter netlab-xxxx_policing { ## send conforming packets to EF term netlab-xxxx { then { policer netlab-xxxx; count netlab-xxxx; forwarding-class expedited-forwarding; accept; } } } } policer netlab-xxxx { if-exceeding { bandwidth-limit 500m; burst-size-limit 50m; } then forwarding-class scavenger; ## over b/w packets st to SS
## for drop, set to “discard” instead } } routing-instances { netlab-xxxx { instance-type vpls; interface xe-0/0/1.3006; protocols { vpls { no-tunnel-services; vpls-id 3006; mtu 9100; ## **Juniper MTU 9100 to match ALU MTU 9114** neighbor 10.96.0.2 { psn-tunnel-endpoint 10.32.0.62; ## follows LSP destination community netlab-xxxx; encapsulation-type ethernet-vlan; } neighbor 10.96.0.8 { psn-tunnel-endpoint 10.32.0.70; ## follows LSP destination community netlab-xxxx; encapsulation-type ethernet-vlan; } } } } }
The corresponding configuration for circuit GRI netlab-‐xxxx on dev-‐mx960-‐rt1 is below. interfaces { xe-11/2/0 { flexible-vlan-tagging; mtu 9192; encapsulation flexible-ethernet-services; unit 3003 { description netlab-xxxx:500000000:oscars-vpls:show:circuit-intercloud; encapsulation vlan-vpls; vlan-id 3003; output-vlan-map swap; family vpls { filter { input netlab-xxxx_stats; output netlab-xxxx_stats; } } } unit 3005 { description netlab-xxxx:500000000:oscars-vpls:show:circuit-intercloud; encapsulation vlan-vpls; vlan-id 3005; output-vlan-map swap; family vpls { filter { input netlab-xxxx_stats; output netlab-xxxx_stats; } } } }
} routing-options { forwarding-table { export [ netlab-xxxx ]; indirect-next-hop; } } protocols { mpls { label-switched-path netlab-xxxx_to_dev-mx80-rt1 { from 10.96.0.2; to 10.32.0.18; metric 65535; bandwidth 500m; priority 4 4; primary netlab-xxxx_to_dev-mx80-rt1; policing filter netlab-xxxx_policing; } label-switched-path netlab-xxxx_to_dev-7750c4-rt1 { from 10.96.0.2; to 10.32.0.70; metric 65535; bandwidth 500m; priority 4 4; primary netlab-xxxx_to_dev-7750c4-rt1; policing filter netlab-xxxx_policing; } path netlab-xxxx_to_dev-mx80-rt1 { 10.32.0.61 strict; 10.32.0.18 strict; } path netlab-xxxx_to_dev-7750c4-rt1 { 10.32.0.70 strict; } } } policy-options { policy-statement netlab-xxxx { term netlab-xxxx { from community netlab-xxxx; then { install-nexthop lsp [ netlab-xxxx_to_dev-mx80-rt1 netlab-xxxx_to_dev-7750c4-rt1 ]; accept; } } } community netlab-xxxx members 65000:3006; } firewall { family vpls { filter netlab-xxxx_stats { interface-specific; term netlab-xxxx_stats { then { count netlab-xxxx_stats; accept; } } } } family any { filter netlab-xxxx_policing {
VPLS GRI netlab-‐xxxx Verification To confirm that the VPLS service is up, all LSPs and VPLS status should show up. As seen below, LSPs in both directions between the three PE routers (dev-‐mx80-‐rt1, dev-‐mx960-‐rt1, and dev-‐7750c4-‐rt1) are up. The following is the LSP status on dev-‐mx80-‐rt1. chin@dev-mx80-rt1> show mpls lsp extensive Ingress LSP: 2 sessions 10.32.0.62 From: 10.96.0.4, State: Up, ActiveRoute: 0, LSPname: netlab-xxxx_to_dev-mx960-rt1 ActivePath: netlab-xxxx_to_dev-mx960-rt1 (primary) LSPtype: Static Configured LoadBalance: Random Metric: 65535 Encoding type: Packet, Switching type: Packet, GPID: IPv4 *Primary netlab-xxxx_to_dev-mx960-rt1 State: Up, Preference: 21 Priorities: 4 4 Bandwidth: 500Mbps SmartOptimizeTimer: 180 Computed ERO (S [L] denotes strict [loose] hops): (CSPF metric: 2000) 10.32.0.17 S 10.32.0.62 S Received RRO (ProtectionFlag 1=Available 2=InUse 4=B/W 8=Node 10=SoftPreempt 20=Node-ID): 10.32.0.17 10.32.0.62 5 Aug 9 16:17:46.991 Selected as active path 4 Aug 9 16:17:46.991 Record Route: 10.32.0.17 10.32.0.62 3 Aug 9 16:17:46.990 Up 2 Aug 9 16:17:46.871 Originate Call 1 Aug 9 16:17:46.871 CSPF: computation result accepted 10.32.0.17 10.32.0.62 Created: Thu Aug 9 16:17:47 2012 10.32.0.70 From: 10.96.0.4, State: Up, ActiveRoute: 0, LSPname: netlab-xxxx_to_dev-7750c4-rt1 ActivePath: netlab-xxxx_to_dev-7750c4-rt1 (primary) LSPtype: Static Configured LoadBalance: Random Metric: 65535 Encoding type: Packet, Switching type: Packet, GPID: IPv4 *Primary netlab-xxxx_to_dev-7750c4-rt1 State: Up, Preference: 21
Priorities: 4 4 Bandwidth: 500Mbps SmartOptimizeTimer: 180 Computed ERO (S [L] denotes strict [loose] hops): (CSPF metric: 2000) 10.32.0.14 S 10.32.0.70 S Received RRO (ProtectionFlag 1=Available 2=InUse 4=B/W 8=Node 10=SoftPreempt 20=Node-ID): 10.32.0.14 10.32.0.70 5 Aug 9 16:56:02.157 Selected as active path 4 Aug 9 16:56:02.151 Record Route: 10.32.0.14 10.32.0.70 3 Aug 9 16:56:02.151 Up 2 Aug 9 16:56:02.051 Originate Call 1 Aug 9 16:56:02.051 CSPF: computation result accepted 10.32.0.14 10.32.0.70 Created: Thu Aug 9 16:56:02 2012 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions 10.32.0.18 From: 10.96.0.2, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-mx80-rt1, LSPpath: Primary Suggested label received: -, Suggested label sent: - Recovery label received: 0, Recovery label sent: - Resv style: 1 FF, Label in: 0, Label out: - Time left: 135, Since: Thu Aug 9 12:44:24 2012 Tspec: rate 500Mbps size 500Mbps peak Infbps m 20 M 9192 Port number: sender 1 receiver 7858 protocol 0 PATH rcvfrom: 10.32.0.17 (ge-1/0/0.0) 9855 pkts Adspec: received MTU 9174 PATH sentto: localclient RESV rcvfrom: localclient Record route: 10.32.0.62 10.32.0.17 <self> 10.96.0.4 From: 10.96.0.8, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Suggested label received: -, Suggested label sent: - Recovery label received: 0, Recovery label sent: - Resv style: 1 SE, Label in: 0, Label out: - Time left: 121, Since: Thu Aug 9 16:06:39 2012 Tspec: rate 0bps size 0bps peak Infbps m 20 M 9194 Port number: sender 55808 receiver 3 protocol 0 PATH rcvfrom: 10.32.0.14 (xe-0/0/0.0) 9558 pkts Adspec: received MTU 9174 PATH sentto: localclient RESV rcvfrom: localclient Record route: 10.32.0.70 10.32.0.14 <self> Total 2 displayed, Up 2, Down 0 Transit LSP: 0 sessions Total 0 displayed, Up 0, Down 0
The following is the LSP status on dev-‐mx960-‐rt1. chin@dev-mx960-rt1> show mpls lsp extensive Ingress LSP: 2 sessions 10.32.0.18 From: 10.96.0.2, State: Up, ActiveRoute: 0, LSPname: netlab-xxxx_to_dev-mx80-rt1 ActivePath: netlab-xxxx_to_dev-mx80-rt1 (primary) LSPtype: Static Configured
LoadBalance: Random Metric: 65535 Encoding type: Packet, Switching type: Packet, GPID: IPv4 *Primary netlab-xxxx_to_dev-mx80-rt1 State: Up, Preference: 21 Priorities: 4 4 Bandwidth: 500Mbps SmartOptimizeTimer: 180 Computed ERO (S [L] denotes strict [loose] hops): (CSPF metric: 2000) 10.32.0.61 S 10.32.0.18 S Received RRO (ProtectionFlag 1=Available 2=InUse 4=B/W 8=Node 10=SoftPreempt 20=Node-ID): 10.32.0.61 10.32.0.18 5 Aug 9 11:40:36.138 Selected as active path 4 Aug 9 11:40:36.137 Record Route: 10.32.0.61 10.32.0.18 3 Aug 9 11:40:36.137 Up 2 Aug 9 11:40:36.124 Originate Call 1 Aug 9 11:40:36.124 CSPF: computation result accepted 10.32.0.61 10.32.0.18 Created: Thu Aug 9 11:40:36 2012 10.32.0.70 From: 10.96.0.2, State: Up, ActiveRoute: 0, LSPname: netlab-xxxx_to_dev-7750c4-rt1 ActivePath: netlab-xxxx_to_dev-7750c4-rt1 (primary) LSPtype: Static Configured LoadBalance: Random Metric: 65535 Encoding type: Packet, Switching type: Packet, GPID: IPv4 *Primary netlab-xxxx_to_dev-7750c4-rt1 State: Up, Preference: 21 Priorities: 4 4 Bandwidth: 500Mbps SmartOptimizeTimer: 180 Computed ERO (S [L] denotes strict [loose] hops): (CSPF metric: 1000) 10.32.0.70 S Received RRO (ProtectionFlag 1=Available 2=InUse 4=B/W 8=Node 10=SoftPreempt 20=Node-ID): 10.32.0.70 5 Aug 9 13:16:53.820 Selected as active path 4 Aug 9 13:16:53.819 Record Route: 10.32.0.70 3 Aug 9 13:16:53.819 Up 2 Aug 9 13:16:53.814 Originate Call 1 Aug 9 13:16:53.814 CSPF: computation result accepted 10.32.0.70 Created: Thu Aug 9 13:16:53 2012 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions 10.32.0.62 From: 10.96.0.4, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-mx960-rt1, LSPpath: Primary Suggested label received: -, Suggested label sent: - Recovery label received: -, Recovery label sent: - Resv style: 1 FF, Label in: 0, Label out: - Time left: 142, Since: Thu Aug 9 15:13:58 2012 Tspec: rate 500Mbps size 500Mbps peak Infbps m 20 M 9192 Port number: sender 1 receiver 2005 protocol 0 PATH rcvfrom: 10.32.0.61 (ge-8/0/0.0) 9582 pkts Adspec: received MTU 9174 PATH sentto: localclient RESV rcvfrom: localclient Record route: 10.32.0.18 10.32.0.61 <self> 10.96.0.2
From: 10.96.0.8, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-mx960-rt1::netlab-xxxx_to_dev-mx960-rt1 Suggested label received: -, Suggested label sent: - Recovery label received: -, Recovery label sent: - Resv style: 1 SE, Label in: 0, Label out: - Time left: 154, Since: Thu Aug 9 12:50:13 2012 Tspec: rate 0bps size 0bps peak Infbps m 20 M 9194 Port number: sender 64002 receiver 2 protocol 0 PATH rcvfrom: 10.32.0.70 (xe-1/0/0.100) 14526 pkts PATH sentto: localclient RESV rcvfrom: localclient Record route: 10.32.0.70 <self> Total 2 displayed, Up 2, Down 0 Transit LSP: 2 sessions 10.32.0.70 From: 10.96.0.4, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-7750c4-rt1, LSPpath: Primary Suggested label received: -, Suggested label sent: - Recovery label received: -, Recovery label sent: 131062 Resv style: 1 FF, Label in: 301040, Label out: 131062 Time left: 116, Since: Thu Aug 9 15:52:13 2012 Tspec: rate 500Mbps size 500Mbps peak Infbps m 20 M 9192 Port number: sender 1 receiver 2007 protocol 0 PATH rcvfrom: 10.32.0.13 (xe-11/3/0.0) 9523 pkts Adspec: received MTU 9174 sent MTU 9174 PATH sentto: 10.32.0.70 (xe-1/0/0.100) 9524 pkts RESV rcvfrom: 10.32.0.70 (xe-1/0/0.100) 14382 pkts Explct route: 10.32.0.70 Record route: 10.32.0.13 <self> 10.32.0.70 10.96.0.4 From: 10.96.0.8, LSPstate: Up, ActiveRoute: 0 LSPname: netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Suggested label received: -, Suggested label sent: - Recovery label received: -, Recovery label sent: 0 Resv style: 1 SE, Label in: 301008, Label out: 0 Time left: 154, Since: Thu Aug 9 15:02:51 2012 Tspec: rate 0bps size 0bps peak Infbps m 20 M 9194 Port number: sender 55808 receiver 3 protocol 0 PATH rcvfrom: 10.32.0.70 (xe-1/0/0.100) 14335 pkts Adspec: sent MTU 9174 PATH sentto: 10.32.0.13 (xe-11/3/0.0) 9589 pkts RESV rcvfrom: 10.32.0.13 (xe-11/3/0.0) 9589 pkts Explct route: 10.32.0.13 10.96.0.4 Record route: 10.32.0.70 <self> 10.32.0.13 Total 2 displayed, Up 2, Down 0
The following is the LSP status on dev-‐7750c4-‐rt1. A:dev-7750c4-rt1# show router mpls lsp detail =============================================================================== MPLS LSPs (Originating) (Detail) =============================================================================== ------------------------------------------------------------------------------- Type : Originating ------------------------------------------------------------------------------- LSP Name : netlab-xxxx_to_dev-mx960-rt1 LSP Type : RegularLsp LSP Tunnel ID : 2 From : 10.96.0.8 To : 10.96.0.2 Adm State : Up Oper State : Up
LSP Up Time : 5d 01:52:25 LSP Down Time : 0d 00:00:00 Transitions : 3 Path Changes : 3 Retry Limit : 0 Retry Timer : 30 sec Signaling : RSVP Resv. Style : SE Hop Limit : 255 Negotiated MTU : 9194 Adaptive : Enabled ClassType : 0 FastReroute : Disabled Oper FR : Disabled CSPF : Disabled ADSPEC : Disabled Metric : 0 Include Grps: Exclude Grps : None None Least Fill : Disabled Auto BW : Disabled LdpOverRsvp : Enabled VprnAutoBind : Enabled IGP Shortcut: Enabled BGP Shortcut : Disabled BGPTransTun : Excluded Oper Metric : 65535 Prop Adm Grp: Disabled CSPFFirstLoose : Disabled Primary(a) : netlab-xxxx_to_dev-mx960-rt1 Up Time : 5d 01:52:25 Bandwidth : 0 Mbps ------------------------------------------------------------------------------- Type : Originating ------------------------------------------------------------------------------- LSP Name : netlab-xxxx_to_dev-mx80-rt1 LSP Type : RegularLsp LSP Tunnel ID : 3 From : 10.96.0.8 To : 10.96.0.4 Adm State : Up Oper State : Up LSP Up Time : 4d 23:39:48 LSP Down Time : 0d 00:00:00 Transitions : 1 Path Changes : 1 Retry Limit : 0 Retry Timer : 30 sec Signaling : RSVP Resv. Style : SE Hop Limit : 255 Negotiated MTU : 9174 Adaptive : Enabled ClassType : 0 FastReroute : Disabled Oper FR : Disabled CSPF : Disabled ADSPEC : Disabled Metric : 0 Include Grps: Exclude Grps : None None Least Fill : Disabled Auto BW : Disabled LdpOverRsvp : Enabled VprnAutoBind : Enabled IGP Shortcut: Enabled BGP Shortcut : Disabled BGPTransTun : Excluded Oper Metric : 65535 Prop Adm Grp: Disabled CSPFFirstLoose : Disabled Primary(a) : netlab-xxxx_to_dev-mx80-rt1 Up Time : 4d 23:39:48 Bandwidth : 0 Mbps =============================================================================== A:dev-7750c4-rt1# show router mpls lsp terminate detail =============================================================================== MPLS LSPs (Terminate) (Detail) =============================================================================== ------------------------------------------------------------------------------- LSP netlab-xxxx_to_dev-7750c4-rt1 ------------------------------------------------------------------------------- From : 10.96.0.2 To : 10.32.0.70 State : Up SetupPriority : 4 Hold Priority : 4
Class Type : 0 In Interface : 1/5/1:100 In Label : 131064 Previous Hop : 10.32.0.69 ------------------------------------------------------------------------------- LSP netlab-xxxx_to_dev-7750c4-rt1 ------------------------------------------------------------------------------- From : 10.96.0.4 To : 10.32.0.70 State : Up SetupPriority : 4 Hold Priority : 4 Class Type : 0 In Interface : 1/5/1:100 In Label : 131062 Previous Hop : 10.32.0.69 ===============================================================================
As reflected below, all PE-‐to-‐PE VPLS sessions are up. The following is the VPLS status on dev-‐mx80-‐rt1. chin@dev-mx80-rt1> show vpls connections extensive Layer-2 VPN connections: Legend for connection status (St) EI -- encapsulation invalid NC -- interface encapsulation not CCC/TCC/VPLS EM -- encapsulation mismatch WE -- interface and instance encaps not same VC-Dn -- Virtual circuit down NP -- interface hardware not present CM -- control-word mismatch -> -- only outbound connection is up CN -- circuit not provisioned <- -- only inbound connection is up OR -- out of range Up -- operational OL -- no outgoing label Dn -- down LD -- local site signaled down CF -- call admission control failure RD -- remote site signaled down SC -- local and remote site ID collision LN -- local site not designated LM -- local site ID not minimum designated RN -- remote site not designated RM -- remote site ID not minimum designated XX -- unknown connection status IL -- no incoming label MM -- MTU mismatch MI -- Mesh-Group ID not available BK -- Backup connection ST -- Standby connection PF -- Profile parse failure PB -- Profile busy RS -- remote site standby SN -- Static Neighbor VM -- VLAN ID mismatch Legend for interface status Up -- operational Dn -- down Instance: netlab-xxxx VPLS-id: 3006 Number of local interfaces: 1 Number of local interfaces up: 1 xe-0/0/1.3006 lsi.1048852 Intf - vpls netlab-xxxx neighbor 10.96.0.2 vpls-id 3006 lsi.1048853 Intf - vpls netlab-xxxx neighbor 10.96.0.8 vpls-id 3006 Neighbor Type St Time last up # Up trans 10.96.0.2(vpls-id 3006) rmt Up Aug 14 12:00:36 2012 1 Remote PE: 10.32.0.62, Negotiated control-word: No Incoming label: 262145, Outgoing label: 262145 Negotiated PW status TLV: No Local interface: lsi.1048852, Status: Up, Encapsulation: VLAN Description: Intf - vpls netlab-xxxx neighbor 10.96.0.2 vpls-id 3006 Connection History: Aug 14 12:00:36 2012 status update timer
Aug 14 12:00:35 2012 PE route changed Aug 14 12:00:35 2012 Out lbl Update 262145 Aug 14 12:00:35 2012 In lbl Update 262145 Aug 14 12:00:35 2012 loc intf up lsi.1048852 10.96.0.8(vpls-id 3006) rmt Up Aug 14 12:05:27 2012 1 Remote PE: 10.32.0.70, Negotiated control-word: No Incoming label: 262146, Outgoing label: 131065 Negotiated PW status TLV: No Local interface: lsi.1048853, Status: Up, Encapsulation: VLAN Description: Intf - vpls netlab-xxxx neighbor 10.96.0.8 vpls-id 3006 Connection History: Aug 14 12:05:27 2012 status update timer Aug 14 12:05:27 2012 PE route changed Aug 14 12:05:27 2012 Out lbl Update 131065 Aug 14 12:05:27 2012 In lbl Update 262146 Aug 14 12:05:27 2012 loc intf up lsi.1048853
The following is the VPLS status on dev-‐mx960-‐rt1. chin@dev-mx960-rt1-re0> show vpls connections extensive Layer-2 VPN connections: Legend for connection status (St) EI -- encapsulation invalid NC -- interface encapsulation not CCC/TCC/VPLS EM -- encapsulation mismatch WE -- interface and instance encaps not same VC-Dn -- Virtual circuit down NP -- interface hardware not present CM -- control-word mismatch -> -- only outbound connection is up CN -- circuit not provisioned <- -- only inbound connection is up OR -- out of range Up -- operational OL -- no outgoing label Dn -- down LD -- local site signaled down CF -- call admission control failure RD -- remote site signaled down SC -- local and remote site ID collision LN -- local site not designated LM -- local site ID not minimum designated RN -- remote site not designated RM -- remote site ID not minimum designated XX -- unknown connection status IL -- no incoming label MM -- MTU mismatch MI -- Mesh-Group ID not availble BK -- Backup connection ST -- Standby connection PF -- Profile parse failure PB -- Profile busy RS -- remote site standby SN -- Static Neighbor Legend for interface status Up -- operational Dn -- down Instance: netlab-xxxx VPLS-id: 3006 Number of local interfaces: 2 Number of local interfaces up: 2 xe-11/2/0.3005 xe-11/2/0.3003 lsi.1049111 Intf - vpls netlab-xxxx neighbor 10.96.0.4 vpls-id 3006 lsi.1049113 Intf - vpls netlab-xxxx neighbor 10.96.0.8 vpls-id 3006 Neighbor Type St Time last up # Up trans 10.96.0.4(vpls-id 3006) rmt Up Aug 14 10:56:43 2012 1 Remote PE: 10.32.0.18, Negotiated control-word: No Incoming label: 262145, Outgoing label: 262145 Negotiated PW status TLV: No Local interface: lsi.1049111, Status: Up, Encapsulation: VLAN Description: Intf - vpls netlab-xxxx neighbor 10.96.0.4 vpls-id 3006 Connection History: Aug 14 10:56:43 2012 status update timer
Aug 14 10:56:43 2012 PE route changed Aug 14 10:56:43 2012 Out lbl Update 262145 Aug 14 10:56:43 2012 In lbl Update 262145 Aug 14 10:56:43 2012 loc intf up lsi.1049111 10.96.0.8(vpls-id 3006) rmt Up Aug 14 10:58:53 2012 1 Remote PE: 10.32.0.70, Negotiated control-word: No Incoming label: 262147, Outgoing label: 131066 Negotiated PW status TLV: No Local interface: lsi.1049113, Status: Up, Encapsulation: VLAN Description: Intf - vpls netlab-xxxx neighbor 10.96.0.8 vpls-id 3006 Connection History: Aug 14 10:58:53 2012 status update timer Aug 14 10:58:53 2012 PE route changed Aug 14 10:58:53 2012 Out lbl Update 131066 Aug 14 10:58:53 2012 In lbl Update 262147 Aug 14 10:58:53 2012 loc intf up lsi.1049113
The following is the VPLS status on dev-‐7750c4-‐rt1. A:dev-7750c4-rt1# show service id 3006 all =============================================================================== Service Detailed Information =============================================================================== Service Id : 3006 Vpn Id : 0 Service Type : VPLS Name : (Not Specified) Description : netlab-xxxx Customer Id : 1 Last Status Change: 08/14/2012 09:45:25 Last Mgmt Change : 08/14/2012 09:45:25 Admin State : Up Oper State : Up MTU : 9114 Def. Mesh VC Id : 3006 SAP Count : 1 SDP Bind Count : 2 Snd Flush on Fail : Disabled Host Conn Verify : Disabled Propagate MacFlush: Disabled Per Svc Hashing : Disabled Allow IP Intf Bind: Disabled Def. Gateway IP : None Def. Gateway MAC : None Temp Flood Time : Disabled Temp Flood : Inactive Temp Flood Chg Cnt: 0 ------------------------------------------------------------------------------- Split Horizon Group specifics ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- ETH-CFM service specifics ------------------------------------------------------------------------------- Tunnel Faults : ignore ------------------------------------------------------------------------------- Service Destination Points(SDPs) ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Sdp Id 3005:3006 -(10.96.0.2) ------------------------------------------------------------------------------- Description : netlab-xxxx_to_dev-mx960-rt1 SDP Id : 3005:3006 Type : Mesh Mesh Descr : (Not Specified) Split Horiz Grp : (Not Specified) VC Type : VLAN VC Tag : 0 Admin Path MTU : 0 Oper Path MTU : 9186
Far End : 10.96.0.2 Delivery : MPLS Tunnel Far End : n/a LSP Types : RSVP Hash Label : Disabled Oper Hash Label : Disabled Admin State : Up Oper State : Up Acct. Pol : None Collect Stats : Disabled Ingress Label : 131066 Egress Label : 262147 Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a Admin ControlWord : Not Preferred Oper ControlWord : False Last Status Change : 08/14/2012 10:58:49 Signaling : TLDP Last Mgmt Change : 08/14/2012 10:58:49 Force Vlan-Vc : Disabled Endpoint : N/A Precedence : 4 PW Status Sig : Disabled Class Fwding State : Down Flags : None Peer Pw Bits : None Peer Fault Ip : None Application Profile: None MAC Pinning : Disabled Oper Group : (none) Monitor Oper Grp : (none) KeepAlive Information : Admin State : Disabled Oper State : Disabled Hello Time : 10 Hello Msg Len : 0 Max Drop Count : 3 Hold Down Time : 10 Statistics : I. Fwd. Pkts. : 139060 I. Dro. Pkts. : 6 I. Fwd. Octs. : 1144228912 I. Dro. Octs. : 612 E. Fwd. Pkts. : 250 E. Fwd. Octets : 60688 MCAC Policy Name : MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited ------------------------------------------------------------------------------- RSVP/Static LSPs ------------------------------------------------------------------------------- Associated LSP List : Lsp Name : netlab-xxxx_to_dev-mx96* Admin State : Up Oper State : Up Time Since Last Tr*: 05d01h57m ------------------------------------------------------------------------------- Class-based forwarding : ------------------------------------------------------------------------------- Class forwarding : Disabled EnforceDSTELspFc : Disabled Default LSP : Uknwn Multicast LSP : None =============================================================================== FC Mapping Table =============================================================================== FC Name LSP Name ------------------------------------------------------------------------------- No FC Mappings ------------------------------------------------------------------------------- Sdp Id 3006:3006 -(10.96.0.4) ------------------------------------------------------------------------------- Description : netlab-xxxx_to_dev-mx80-rt1
SDP Id : 3006:3006 Type : Mesh Mesh Descr : (Not Specified) Split Horiz Grp : (Not Specified) VC Type : VLAN VC Tag : 0 Admin Path MTU : 0 Oper Path MTU : 9166 Far End : 10.96.0.4 Delivery : MPLS Tunnel Far End : n/a LSP Types : RSVP Hash Label : Disabled Oper Hash Label : Disabled Admin State : Up Oper State : Up Acct. Pol : None Collect Stats : Disabled Ingress Label : 131065 Egress Label : 262146 Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a Admin ControlWord : Not Preferred Oper ControlWord : False Last Status Change : 08/14/2012 11:01:36 Signaling : TLDP Last Mgmt Change : 08/14/2012 11:01:36 Force Vlan-Vc : Disabled Endpoint : N/A Precedence : 4 PW Status Sig : Disabled Class Fwding State : Down Flags : None Peer Pw Bits : None Peer Fault Ip : None Application Profile: None MAC Pinning : Disabled Oper Group : (none) Monitor Oper Grp : (none) KeepAlive Information : Admin State : Disabled Oper State : Disabled Hello Time : 10 Hello Msg Len : 0 Max Drop Count : 3 Hold Down Time : 10 Statistics : I. Fwd. Pkts. : 139120 I. Dro. Pkts. : 256 I. Fwd. Octs. : 1144523904 I. Dro. Octs. : 34056 E. Fwd. Pkts. : 139235 E. Fwd. Octets : 1144487066 MCAC Policy Name : MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited ------------------------------------------------------------------------------- RSVP/Static LSPs ------------------------------------------------------------------------------- Associated LSP List : Lsp Name : netlab-xxxx_to_dev-mx80* Admin State : Up Oper State : Up Time Since Last Tr*: 04d23h44m ------------------------------------------------------------------------------- Class-based forwarding : ------------------------------------------------------------------------------- Class forwarding : Disabled EnforceDSTELspFc : Disabled Default LSP : Uknwn Multicast LSP : None =============================================================================== FC Mapping Table =============================================================================== FC Name LSP Name ------------------------------------------------------------------------------- No FC Mappings
------------------------------------------------------------------------------- Number of SDPs : 2 ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Service Access Points ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- SAP 1/5/2:3004 ------------------------------------------------------------------------------- Service Id : 3006 SAP : 1/5/2:3004 Encap : q-tag Description : (Not Specified) Admin State : Up Oper State : Up Flags : None Multi Svc Site : None Last Status Change : 08/14/2012 09:45:25 Last Mgmt Change : 08/13/2012 14:35:56 Sub Type : regular Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100 Split Horizon Group: (Not Specified) Max Nbr of MAC Addr: No Limit Total MAC Addr : 0 Learned MAC Addr : 0 Static MAC Addr : 0 Admin MTU : 9212 Oper MTU : 9212 Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a tod-suite : None qinq-pbit-marking : both Ing Agg Rate Limit : max Egr Agg Rate Limit: max Q Frame-Based Acct : Disabled ARP Reply Agent : Disabled Host Conn Verify : Disabled Mac Learning : Enabled Discard Unkwn Srce: Disabled Mac Aging : Enabled Mac Pinning : Disabled BPDU Translation : Disabled L2PT Termination : Disabled Vlan-translation : None Acct. Pol : None Collect Stats : Disabled Anti Spoofing : None Avl Static Hosts : 0 Tot Static Hosts : 0 Calling-Station-Id : n/a Application Profile: None Oper Group : (none) Monitor Oper Grp : (none) MCAC Policy Name : MCAC Const Adm St : Enable MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited Restr MacProt Src : Disabled Restr MacUnpr Dst : Disabled Time to RetryReset : never Retries Left : 3 Mac Move : Blockable Blockable Level : Tertiary Egr MCast Grp : Auth Policy : None ------------------------------------------------------------------------------- ETH-CFM SAP specifics ------------------------------------------------------------------------------- Tunnel Faults : n/a AIS : Disabled MC Prop-Hold-Timer : n/a
------------------------------------------------------------------------------- Stp Service Access Point specifics ------------------------------------------------------------------------------- Stp Admin State : Up Stp Oper State : Down Core Connectivity : Down Port Role : N/A Port State : Forwarding Port Number : 2048 Port Priority : 128 Port Path Cost : 10 Auto Edge : Enabled Admin Edge : Disabled Oper Edge : N/A Link Type : Pt-pt BPDU Encap : Dot1d Root Guard : Disabled Active Protocol : N/A Last BPDU from : N/A CIST Desig Bridge : N/A Designated Port : N/A Forward transitions: 0 Bad BPDUs rcvd : 0 Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0 TCN BPDUs rcvd : 0 TCN BPDUs tx : 0 TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0 RST BPDUs rcvd : 0 RST BPDUs tx : 0 MST BPDUs rcvd : 0 MST BPDUs tx : 0 ------------------------------------------------------------------------------- ARP host ------------------------------------------------------------------------------- Admin State : outOfService Host Limit : 1 Min Auth Interval : 15 minutes ------------------------------------------------------------------------------- QOS ------------------------------------------------------------------------------- Ingress qos-policy : 3006 Egress qos-policy : 1 Shared Q plcy : n/a Multipoint shared : Disabled I. Sched Pol : (Not Specified) E. Sched Pol : (Not Specified) I. Policer Ctl Pol : (Not Specified) E. Policer Ctl Pol : (Not Specified) ------------------------------------------------------------------------------- DHCP ------------------------------------------------------------------------------- Description : (Not Specified) Admin State : Down Lease Populate : 0 DHCP Snooping : Down Action : Keep Proxy Admin State : Down Proxy Lease Time : N/A Emul. Server Addr : Not Configured ------------------------------------------------------------------------------- Subscriber Management ------------------------------------------------------------------------------- Admin State : Down MAC DA Hashing : False Def Sub-Id : None Def Sub-Profile : None Def SLA-Profile : None Def Inter-Dest-Id : None Sub-Ident-Policy : None Subscriber Limit : 1 Single-Sub-Parameters Prof Traffic Only : False Non-Sub-Traffic : N/A ------------------------------------------------------------------------------- Sap Statistics ------------------------------------------------------------------------------- Last Cleared Time : N/A
Bridge Priority : 32768 Tx Hold Count : 6 Topology Change : Inactive Bridge Hello Time : 2 Last Top. Change : 0d 00:00:00 Bridge Max Age : 20 Top. Change Count : 0 Bridge Fwd Delay : 15 MST region revision: 0 Bridge max hops : 20 MST region name : Root Bridge : N/A Primary Bridge : N/A Root Path Cost : 0 Root Forward Delay: 0 Rcvd Hello Time : 0 Root Max Age : 0 Root Priority : 0 Root Port : N/A ------------------------------------------------------------------------------- Forwarding Database specifics ------------------------------------------------------------------------------- Service Id : 3006 Mac Move : Disabled Primary Factor : 3 Secondary Factor : 2 Mac Move Rate : 2 Mac Move Timeout : 10 Mac Move Retries : 3 Table Size : 4096 Total Count : 0 Learned Count : 0 Static Count : 0 OAM-learned Count : 0 DHCP-learned Count: 0 Host-learned Count: 0 Intf-learned Count: 0 Remote Age : 900 Local Age : 300 High Watermark : 95% Low Watermark : 90% Mac Learning : Enabled Discard Unknown : Disabled Mac Aging : Enabled Relearn Only : False Mac Subnet Len : 48 ------------------------------------------------------------------------------- IGMP Snooping Base info ------------------------------------------------------------------------------- Admin State : Down Querier : No querier found ------------------------------------------------------------------------------- Sap/Sdp Oper MRtr Pim Send Max Max MVR Num Id State Port Port Qries Grps Srcs From-VPLS Grps ------------------------------------------------------------------------------- sap:1/5/2:3004 Up No No No None None Local 0 sdp:3005:3006 Up No No No None None N/A 0 sdp:3006:3006 Up No No No None None N/A 0 ------------------------------------------------------------------------------- MLD Snooping Base info ------------------------------------------------------------------------------- Admin State : Down Querier : No querier found ------------------------------------------------------------------------------- Sap/Sdp Oper MRtr Send Max Num MVR Num Id State Port Queries Groups From-VPLS Groups ------------------------------------------------------------------------------- sap:1/5/2:3004 Up No Disabled No Limit Local 0 sdp:3005:3006 Up No Disabled No Limit N/A 0 sdp:3006:3006 Up No Disabled No Limit N/A 0 ------------------------------------------------------------------------------- DHCP Summary, service 3006 ------------------------------------------------------------------------------- Sap/Sdp Snoop Used/ Arp Reply Info Admin Provided Agent Option State -------------------------------------------------------------------------------
sap:1/5/2:3004 No 0/0 No Keep Down sdp:3005:3006 No N/A N/A N/A N/A sdp:3006:3006 No N/A N/A N/A N/A ------------------------------------------------------------------------------- Number of Entries : 3 ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- ARP host Summary, service 3006 ------------------------------------------------------------------------------- Sap Used Provided Admin State ------------------------------------------------------------------------------- sap:1/5/2:3004 0 1 outOfService ------------------------------------------------------------------------------- Number of SAPs : 1 0 ------------------------------------------------------------------------------- =============================================================================== Service VPLS Group Information =============================================================================== =============================================================================== ------------------------------------------------------------------------------- Service Endpoints ------------------------------------------------------------------------------- No Endpoints found. =============================================================================== VPLS Sites =============================================================================== Site Site-Id Dest Mesh-SDP Admin Oper Fwdr ------------------------------------------------------------------------------- No Matching Entries =============================================================================== ===============================================================================
VPLS GRI netlab-‐xxxx Usage
Traffic Flow netlap-‐pt6 -‐> netlap-‐pt5 To demonstrate the use of the Ethernet VLAN service VPLS netlab-‐xxxx, a 900Mbs UDP stream is sent from netlab-‐pt6 to netlab-‐pt5 using iperf. The following output shows the results from the iperf client/source (netlab-‐pt6) and server/sink (netlab-‐pt5) respectively. chin@netlab-pt6:/home/chin> iperf -c 192.168.30.5 -b900m -l8k -i1 WARNING: option -b implies udp testing ------------------------------------------------------------ Client connecting to 192.168.30.5, UDP port 5001 Sending 8192 byte datagrams UDP buffer size: 9.00 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.6 port 64551 connected with 192.168.30.5 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 1.0- 2.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth
The following output shows the various counters on dev-‐mx80-‐rt1 for the VPLS netlab-‐xxxx. chin@dev-mx80-rt1> show firewall filter netlab-xxxx_stats-xe-0/0/1.3006-i Filter: netlab-xxxx_stats-xe-0/0/1.3006-i Counters: Name Bytes Packets netlab-xxxx_stats-xe-0/0/1.3006-i 1144184058 138891 chin@dev-mx80-rt1> show firewall filter netlab-xxxx_stats-xe-0/0/1.3006-o
Filter: netlab-xxxx_stats-xe-0/0/1.3006-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-0/0/1.3006-o 8238 1 chin@dev-mx80-rt1> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-mx960-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-mx960-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-mx960-rt1 1144184058 138891 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-mx960-rt1 482046570 58515 chin@dev-mx80-rt1> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up 138891 1144184058 netlab-xxxx_to_dev-mx960-rt1 10.32.0.70 10.96.0.4 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up NA NA netlab-xxxx_to_dev-mx80-rt1 10.96.0.4 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 0 sessions Total 0 displayed, Up 0, Down 0
The following output shows the various counters on the intermediate router dev-‐m10-‐rt3 for the circuit netlab-‐xxxx. chin@dev-m10-rt3-re0> show mpls lsp statistics Ingress LSP: 0 sessions Total 0 displayed, Up 0, Down 0 Egress LSP: 0 sessions Total 0 displayed, Up 0, Down 0 Transit LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up 1 8246 netlab-xxxx_to_dev-mx80-rt1 10.32.0.62 10.96.0.4 Up 138891 1145295186 netlab-xxxx_to_dev-mx960-rt1 Total 2 displayed, Up 2, Down 0
The following output shows the various counters on dev-‐m960-‐rt1 for the circuit netlab-‐xxxx. chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3005-i Filter: netlab-xxxx_stats-xe-11/2/0.3005-i
Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3005-i 8242 1 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3005-o Filter: netlab-xxxx_stats-xe-11/2/0.3005-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3005-o 1144739622 138891 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-mx80-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-mx80-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-mx80-rt1 8242 1 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-mx80-rt1 0 0 {master} chin@dev-mx960-rt1-re0> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up 1 8246 netlab-xxxx_to_dev-mx80-rt1 10.32.0.70 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up NA NA netlab-xxxx_to_dev-mx960-rt1 10.96.0.2 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx960-rt1::netlab-xxxx_to_dev-mx960-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.70 10.96.0.4 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 10.96.0.4 10.96.0.8 Up 0 0 netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0
Traffic Flow netlap-‐pt5 -‐> netlap-‐pt3 To demonstrate the use of the Ethernet VLAN service VPLS netlab-‐xxxx, a 900Mbs UDP stream is sent from netlab-‐pt5 to netlab-‐pt3 using iperf. The following output shows the results from the iperf client/source (netlab-‐pt5) and server/sink (netlab-‐pt3) respectively. chin@netlab-pt5:/home/chin> iperf -c 192.168.30.3 -b900m -l8k -i1
WARNING: option -b implies udp testing ------------------------------------------------------------ Client connecting to 192.168.30.3, UDP port 5001 Sending 8192 byte datagrams UDP buffer size: 9.00 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.5 port 62932 connected with 192.168.30.3 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 1.0- 2.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 6.0- 7.0 sec 108 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 7.0- 8.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 9.0-10.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec [ 3] Sent 138890 datagrams [ 3] Server Report: [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.001 ms 0/138890 (0%) chin@netlab-pt3:/home/chin> iperf -s -u -l8k -i1 ------------------------------------------------------------ Server listening on UDP port 5001 Receiving 8192 byte datagrams UDP buffer size: 512 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.3 port 5001 connected with 192.168.30.5 port 62932 [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 0.0- 1.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13891 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 1.0- 2.0 sec 108 MBytes 910 Mbits/sec 0.001 ms 0/13888 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 6.0- 7.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 7.0- 8.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.001 ms 0/138890 (0%)
The following output shows the various counters on dev-‐mx960-‐rt1 for the VPLS netlab-‐xxxx. {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3003-i Filter: netlab-xxxx_stats-xe-11/2/0.3003-i Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3003-i 8242 1 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3003-o Filter: netlab-xxxx_stats-xe-11/2/0.3003-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3003-o 1144739622 138891 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3005-i Filter: netlab-xxxx_stats-xe-11/2/0.3005-i Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3005-i 1144739622 138891 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3005-o Filter: netlab-xxxx_stats-xe-11/2/0.3005-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3005-o 8242 1 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-mx80-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-mx80-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-mx80-rt1 0 0 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-mx80-rt1 0 0 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 0 0 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 0 0
{master} chin@dev-mx960-rt1-re0> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-mx80-rt1 10.32.0.70 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up NA NA netlab-xxxx_to_dev-mx960-rt1 10.96.0.2 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx960-rt1::netlab-xxxx_to_dev-mx960-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.70 10.96.0.4 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 10.96.0.4 10.96.0.8 Up 0 0 netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0
Traffic Flow netlap-‐pt3 -‐> netlap-‐pt4 To demonstrate the use of the Ethernet VLAN service VPLS netlab-‐xxxx, a 900Mbs UDP stream is sent from netlab-‐pt3 to netlab-‐pt4 using iperf. The following output shows the results from the iperf client/source (netlab-‐pt3) and server/sink (netlab-‐pt4) respectively. chin@netlab-pt3:/home/chin> iperf -c 192.168.30.4 -b900m -l8k -i1 WARNING: option -b implies udp testing ------------------------------------------------------------ Client connecting to 192.168.30.4, UDP port 5001 Sending 8192 byte datagrams UDP buffer size: 9.00 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.3 port 57248 connected with 192.168.30.4 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 1.0- 2.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 6.0- 7.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 7.0- 8.0 sec 108 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec
[ ID] Interval Transfer Bandwidth [ 3] 9.0-10.0 sec 109 MBytes 910 Mbits/sec [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec [ 3] Sent 138890 datagrams [ 3] Server Report: [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.000 ms 0/138890 (0%) chin@netlab-noc:/home/chin% iperf -s -u -l8k -i1 ------------------------------------------------------------ Server listening on UDP port 5001 Receiving 8192 byte datagrams UDP buffer size: 1.00 MByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.4 port 5001 connected with 192.168.30.3 port 57248 [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 3] 0.0- 1.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13891 (0%) [ 3] 1.0- 2.0 sec 108 MBytes 910 Mbits/sec 0.001 ms 0/13888 (0%) [ 3] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 6.0- 7.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 7.0- 8.0 sec 109 MBytes 910 Mbits/sec 0.000 ms 0/13889 (0%) [ 3] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec 0.001 ms 0/13889 (0%) [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.001 ms 0/138890 (0%)
The following output shows the various counters on dev-‐mx960-‐rt1 for the VPLS netlab-‐xxxx. {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3003-i Filter: netlab-xxxx_stats-xe-11/2/0.3003-i Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3003-i 1144731380 138890 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_stats-xe-11/2/0.3003-o Filter: netlab-xxxx_stats-xe-11/2/0.3003-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-11/2/0.3003-o 8242 1 {master} chin@dev-mx960-rt1-re0> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 1144731380 138890 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 492995230 59815
{master} chin@dev-mx960-rt1-re0> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-mx80-rt1 10.32.0.70 10.96.0.2 Up 138890 1145286940 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up NA NA netlab-xxxx_to_dev-mx960-rt1 10.96.0.2 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx960-rt1::netlab-xxxx_to_dev-mx960-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.70 10.96.0.4 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 10.96.0.4 10.96.0.8 Up 0 0 netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0
The following output shows the various counters on dev-‐7750c4-‐rt1 for the VPLS netlab-‐xxxx. A:dev-7750c4-rt1>clear>service>stats>id# show service id 3006 sap 1/5/2:3004 stats =============================================================================== Service Access Points(SAP) =============================================================================== Service Id : 3006 SAP : 1/5/2:3004 Encap : q-tag Description : (Not Specified) Admin State : Up Oper State : Up Flags : None Multi Svc Site : None Last Status Change : 08/14/2012 09:45:25 Last Mgmt Change : 08/13/2012 14:35:56 ------------------------------------------------------------------------------- ETH-CFM SAP specifics ------------------------------------------------------------------------------- Tunnel Faults : n/a AIS : Disabled MC Prop-Hold-Timer : n/a ------------------------------------------------------------------------------- Sap per Queue stats ------------------------------------------------------------------------------- Packets Octets Ingress Queue 1 (Unicast) (Priority) Off. HiPrio : 0 0 Off. LoPrio : 0 0 Dro. HiPrio : 0 0 Dro. LoPrio : 0 0 For. InProf : 0 0 For. OutProf : 0 0
Traffic Flow netlap-‐pt4 -‐> netlap-‐pt6 To demonstrate the use of the Ethernet VLAN service VPLS netlab-‐xxxx, a 900Mbs UDP stream is sent from netlab-‐pt4 to netlab-‐pt6 using iperf. The following output shows the results from the iperf client/source (netlab-‐pt4) and server/sink (netlab-‐pt6) respectively. chin@netlab-noc:/home/chin% iperf -c 192.168.30.6 -b900m -l8k -i1 WARNING: option -b implies udp testing ------------------------------------------------------------ Client connecting to 192.168.30.6, UDP port 5001 Sending 8192 byte datagrams UDP buffer size: 9.00 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.30.4 port 62517 connected with 192.168.30.6 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 108 MBytes 910 Mbits/sec [ 3] 1.0- 2.0 sec 109 MBytes 910 Mbits/sec [ 3] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec [ 3] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec [ 3] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec [ 3] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec [ 3] 6.0- 7.0 sec 109 MBytes 910 Mbits/sec [ 3] 7.0- 8.0 sec 109 MBytes 910 Mbits/sec [ 3] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec [ 3] 9.0-10.0 sec 109 MBytes 910 Mbits/sec [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec [ 3] Sent 138887 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.007 ms 0/138886 (0%) [ 3] 0.0-10.0 sec 1 datagrams received out-of-order chin@netlab-pt6:/home/chin> iperf -s -l8k -u -i1 ------------------------------------------------------------ Server listening on UDP port 5001 Receiving 8192 byte datagrams
UDP buffer size: 512 KByte (default) ------------------------------------------------------------ [ 4] local 192.168.30.6 port 5001 connected with 192.168.30.4 port 62517 [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 0.0- 1.0 sec 108 MBytes 910 Mbits/sec 0.006 ms 0/13884 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 1.0- 2.0 sec 109 MBytes 910 Mbits/sec 0.006 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 2.0- 3.0 sec 109 MBytes 910 Mbits/sec 0.006 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 3.0- 4.0 sec 109 MBytes 910 Mbits/sec 0.006 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 4.0- 5.0 sec 109 MBytes 910 Mbits/sec 0.006 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 5.0- 6.0 sec 109 MBytes 910 Mbits/sec 0.006 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 6.0- 7.0 sec 109 MBytes 910 Mbits/sec 0.005 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 7.0- 8.0 sec 109 MBytes 910 Mbits/sec 0.005 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 8.0- 9.0 sec 109 MBytes 910 Mbits/sec 0.005 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 9.0-10.0 sec 109 MBytes 910 Mbits/sec 0.005 ms 0/13889 (0%) [ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams [ 4] 0.0-10.0 sec 1.06 GBytes 910 Mbits/sec 0.007 ms 0/138886 (0%) [ 4] 0.0-10.0 sec 1 datagrams received out-of-order
The following output shows the various counters on dev-‐7750c4-‐rt1 for the circuit netlab-‐xxxx. A:dev-7750c4-rt1# show service id 3006 sap 1/5/2:3004 stats =============================================================================== Service Access Points(SAP) =============================================================================== Service Id : 3006 SAP : 1/5/2:3004 Encap : q-tag Description : (Not Specified) Admin State : Up Oper State : Up Flags : None Multi Svc Site : None Last Status Change : 08/14/2012 09:45:25 Last Mgmt Change : 08/13/2012 14:35:56 ------------------------------------------------------------------------------- ETH-CFM SAP specifics ------------------------------------------------------------------------------- Tunnel Faults : n/a AIS : Disabled MC Prop-Hold-Timer : n/a ------------------------------------------------------------------------------- Sap per Queue stats ------------------------------------------------------------------------------- Packets Octets Ingress Queue 1 (Unicast) (Priority) Off. HiPrio : 0 0 Off. LoPrio : 0 0 Dro. HiPrio : 0 0 Dro. LoPrio : 0 0 For. InProf : 0 0 For. OutProf : 0 0
The following output shows the various counters on the intermediate router dev-‐mx960-‐rt1 for the VPLS netlab-‐xxxx. chin@dev-mx960-rt1-re0> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-mx80-rt1 10.32.0.70 10.96.0.2 Up 0 0 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up NA NA netlab-xxxx_to_dev-mx960-rt1 10.96.0.2 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx960-rt1::netlab-xxxx_to_dev-mx960-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.70 10.96.0.4 Up 1 8246 netlab-xxxx_to_dev-7750c4-rt1 10.96.0.4 10.96.0.8 Up 138888 1145270448 netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0
The following output shows the various counters on dev-‐m80-‐rt1 for the VPLS netlab-‐xxxx. chin@dev-mx80-rt1> show firewall filter netlab-xxxx_stats-xe-0/0/1.3006-i Filter: netlab-xxxx_stats-xe-0/0/1.3006-i Counters: Name Bytes Packets netlab-xxxx_stats-xe-0/0/1.3006-i 8238 1
chin@dev-mx80-rt1> show firewall filter netlab-xxxx_stats-xe-0/0/1.3006-o Filter: netlab-xxxx_stats-xe-0/0/1.3006-o Counters: Name Bytes Packets netlab-xxxx_stats-xe-0/0/1.3006-o 1144159344 138888 chin@dev-mx80-rt1> show firewall filter netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Filter: netlab-xxxx_policing-netlab-xxxx_to_dev-7750c4-rt1 Counters: Name Bytes Packets netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 8238 1 Policers: Name Bytes Packets netlab-xxxx-netlab-xxxx-netlab-xxxx_to_dev-7750c4-rt1 0 0 chin@dev-mx80-rt1> show mpls lsp statistics Ingress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.62 10.96.0.4 Up 0 0 netlab-xxxx_to_dev-mx960-rt1 10.32.0.70 10.96.0.4 Up 1 8238 netlab-xxxx_to_dev-7750c4-rt1 Total 2 displayed, Up 2, Down 0 Egress LSP: 2 sessions To From State Packets Bytes LSPname 10.32.0.18 10.96.0.2 Up NA NA netlab-xxxx_to_dev-mx80-rt1 10.96.0.4 10.96.0.8 Up NA NA netlab-xxxx_to_dev-mx80-rt1::netlab-xxxx_to_dev-mx80-rt1 Total 2 displayed, Up 2, Down 0 Transit LSP: 0 sessions Total 0 displayed, Up 0, Down 0
Configuration Reference for dev-‐mx80-‐rt1 chin@dev-mx80-rt1> show version Hostname: dev-mx80-rt1 Model: mx80 JUNOS Base OS boot [11.4I20120329_0821_mmiklus] JUNOS Base OS Software Suite [11.4I20120329_0821_mmiklus] JUNOS Kernel Software Suite [11.4I20120329_0821_mmiklus] JUNOS Crypto Software Suite [11.4I20120329_0821_mmiklus] JUNOS Packet Forwarding Engine Support (MX80) [11.4I20120329_0821_mmiklus] JUNOS Online Documentation [11.4I20120329_0821_mmiklus] JUNOS Routing Software Suite [11.4I20120329_0821_mmiklus] SDK OpenFlow Application v1.3c [11.4I20120711_0958_fabian] chin@dev-mx80-rt1> show chassis hardware Hardware inventory: Item Version Part number Serial number Description Chassis D4496 MX80 Midplane REV 06 711-031594 YG7544 MX80 PEM 0 Rev 03 740-028288 UF00608 AC Power Entry Module PEM 1 Rev 03 740-028288 UF00486 AC Power Entry Module Routing Engine BUILTIN BUILTIN Routing Engine TFEB 0 BUILTIN BUILTIN Forwarding Engine Processor QXM 0 REV 05 711-028408 YG7065 MPC QXM FPC 0 BUILTIN BUILTIN MPC BUILTIN MIC 0 BUILTIN BUILTIN 4x 10GE XFP PIC 0 BUILTIN BUILTIN 4x 10GE XFP Xcvr 0 REV 01 740-014289 T08D77282 XFP-10G-SR Xcvr 1 REV 01 740-014279 83E239N01144 XFP-10G-LR FPC 1 BUILTIN BUILTIN MPC BUILTIN MIC 0 REV 22 750-028392 YG5226 3D 20x 1GE(LAN) SFP PIC 0 BUILTIN BUILTIN 10x 1GE(LAN) SFP Xcvr 0 REV 01 740-011613 AM0815S9A1M SFP-SX PIC 1 BUILTIN BUILTIN 10x 1GE(LAN) SFP Xcvr 0 REV 02 740-011613 AM0925SBP6Z SFP-SX Xcvr 1 REV 01 740-011613 E08C04762 SFP-SX MIC 1 REV 18 750-028380 YH1681 3D 2x 10GE XFP PIC 2 BUILTIN BUILTIN 1x 10GE XFP PIC 3 BUILTIN BUILTIN 1x 10GE XFP Fan Tray Fan Tray chin@dev-mx80-rt1> show configuration ## Last commit: 2012-07-10 11:47:49 PDT by chin version 10.4R9.2; groups { re0 { system { host-name dev-mx80-rt1; backup-router 192.74.211.1; } interfaces { fxp0 { unit 0 { family inet { address 192.74.211.17/25 { primary; } } } } } } sdn-cos-group { class-of-service { interfaces { <*> { scheduler-map esnet_sdn_scheduler; unit * {
classifiers { dscp esnet_dscp_classifier; dscp-ipv6 esnet_dscp-ipv6_classifier; exp esnet_exp_classifier; } rewrite-rules { dscp esnet_dscp_rewrite-rules; dscp-ipv6 esnet_dscp-ipv6_rewrite-rules; exp esnet_exp_rewrite-rules; } } } } } } } apply-groups re0; system { domain-name es.net; time-zone America/Los_Angeles; } interfaces { xe-0/0/0 { description "dev-mx80-rt1(xe-0/0/0)->dev-mx960-rt1(xe-11/3/0)"; mtu 9192; unit 0 { description "dev-mx80-rt1(xe-0/0/0.0)->dev-mx960-rt1(xe-11/3/0.0)"; family inet { mtu 9174; address 10.32.0.13/30; } family iso; family mpls; } } xe-0/0/1 { description "dev-mx80-rt1(xe-0/0/1)->dev-6509-rt3(Te9/4)"; flexible-vlan-tagging; mtu 9192; encapsulation flexible-ethernet-services; unit 3006 { description netlab-xxxx:500000000:oscars-vpls:show:circuit-intercloud; encapsulation vlan-vpls; vlan-id 3006; output-vlan-map swap; family vpls { filter { input netlab-xxxx_stats; output netlab-xxxx_stats; } } } } ge-1/0/0 { description "dev-mx80-rt1(ge-1/0/0)->dev-m10-rt3(ge-1/2/0)"; mtu 9192; unit 0 { description "dev-mx80-rt1(ge-1/0/0.0)->dev-m10-rt3(ge-1/2/0.0)"; family inet { mtu 9174; address 10.32.0.18/30; } family iso; family mpls; } } lo0 { description dev-mx80-rt1::loopback:show:na; unit 0 { description dev-mx80-rt1::loopback:show:na; family inet {
Configuration Reference for dev-‐7750c4-‐rt1 A:dev-7750c4-rt1# show version TiMOS-B-9.0.R2 both/hops ALCATEL SR 7750 Copyright (c) 2000-2011 Alcatel-Lucent. All rights reserved. All use subject to applicable license agreements. Built on Tue Apr 5 14:49:00 PDT 2011 by builder in /rel9.0/b1/R2/panos/main A:dev-7750c4-rt1# show chassis =============================================================================== Chassis Information =============================================================================== Name : dev-7750c4-rt1 Type : 7750 SR-c4 Location : Coordinates : CLLI code : Number of slots : 2 Number of ports : 23 Critical LED state : Off Major LED state : Off Minor LED state : Off Over Temperature state : OK Base MAC address : 7c:20:64:ad:6e:ab Hardware Data Part number : CLEI code : Serial number : A6102300114 Manufacture date : Manufacturing string : Manufacturing deviations : Manufacturing assembly number : Time of last boot : 1999/12/31 16:00:13 Current alarm state : alarm cleared ------------------------------------------------------------------------------- Environment Information Number of fan trays : 1 Number of fans : 4 Fan tray number : 1 Status : up Revision : hf-fan-2 Speed : half speed ------------------------------------------------------------------------------- Power Supply Information Number of power supplies : 2 Power supply number : 1 Defaulted power supply type : dc Status : up Input power : within range Output power : within range Power supply number : 2 Defaulted power supply type : dc Status : failed Input power : out of range Output power : out of range ------------------------------------------------------------------------------- Chassis Control Module (CCM) Information CCM number : 1 Equipped : yes Type : ccm-c4-xp Hardware Data Platform type : 7750 Part number :
CLEI code : Serial number : Stromboli06497_CCM Manufacture date : Manufacturing string : Manufacturing deviations : Manufacturing assembly number : Administrative state : up Operational state : up Temperature : 45C Temperature threshold : 75C Time of last boot : N/A Current alarm state : alarm cleared =============================================================================== A:dev-7750c4-rt1# show card detail =============================================================================== Card 1 =============================================================================== Slot Provisioned Equipped Admin Operational Comments Card-type Card-type State State ------------------------------------------------------------------------------- 1 iom-c4-xp iom-c4-xp up up IOM Card Specific Data Clock source : none Named Pool Mode : Disabled Available MDA slots : 5 Installed MDAs : 2 FP 1 Specific Data WRED Admin State : Out Of Service WRED buffer-allocation max : 2500 WRED buffer-allocation min : 2500 WRED reserved-cbs max : 2500 WRED reserved-cbs min : 2500 WRED Slope Policy : default hi-bw-mc-srcEgress Alarm : 2 hi-bw-mc-srcEgress Group : 0 mc-path-mgmt Admin State : Out Of Service Ingress Bandwidth Policy : default Hardware Data Platform type : 7750 Part number : CLEI code : Serial number : Stromboli06497 Manufacture date : Manufacturing string : Manufacturing deviations : Manufacturing assembly number : Administrative state : up Operational state : up Temperature : 48C Temperature threshold : 75C Software boot (rom) version : X-9.0.R2 on Tue Apr 5 14:27:12 PDT 2011 by * Software version : TiMOS-B-9.0.R2 both/hops ALCATEL SR 7750 Co* Time of last boot : 2012/07/25 15:07:27 Current alarm state : alarm cleared Base MAC address : 00:03:fa:1d:8f:56 Last bootup reason : hard boot Memory capacity : 4,096 MB =============================================================================== Card A =============================================================================== Slot Provisioned Equipped Admin Operational Comments Card-type Card-type State State ------------------------------------------------------------------------------- A cfm-c4-xp cfm-c4-xp up up/active
BOF last modified : N/A Config file version : FRI JAN 21 04:54:50 2000 UTC Config file last modified : N/A Config file last saved : 2012/08/15 14:29:15 M/S clocking ref state : primary Flash - cf1: Administrative State : up Operational state : not equipped Flash - cf2: Administrative State : up Operational state : not equipped Flash - cf3: Administrative State : up Operational state : up Serial number : STI1M27409061075114 Firmware revision : 01/17/07 Model number : STI Flash 8.0.0 Size : 998,656 KB Free space : 821,920 KB Hardware Data Platform type : 7750 Part number : CLEI code : Serial number : Stromboli06497 Manufacture date : Manufacturing string : Manufacturing deviations : Manufacturing assembly number : Administrative state : up Operational state : up Temperature : 48C Temperature threshold : 75C Software boot (rom) version : X-9.0.R2 on Tue Apr 5 14:27:12 PDT 2011 by * Software version : TiMOS-B-9.0.R2 both/hops ALCATEL SR 7750 Co* Time of last boot : 1999/12/31 16:00:13 Current alarm state : alarm cleared Base MAC address : 00:03:fa:1d:8f:56 Memory capacity : 4,096 MB =============================================================================== A:dev-7750c4-rt1# admin display-config # TiMOS-B-9.0.R2 both/hops ALCATEL SR 7750 Copyright (c) 2000-2011 Alcatel-Lucent. # All rights reserved. All use subject to applicable license agreements. # Built on Tue Apr 5 14:49:00 PDT 2011 by builder in /rel9.0/b1/R2/panos/main # Generated WED AUG 15 21:31:41 2012 UTC exit all configure #-------------------------------------------------- echo "System Configuration" #-------------------------------------------------- system name "dev-7750c4-rt1" ccm 1 exit exit #-------------------------------------------------- echo "QoS Policy Configuration" #-------------------------------------------------- qos network-queue "esnet-network-queue-qos-policy" create description "ESnet Network Interface Queue QoS Policy" queue 1 create mbs 50