Error Codes R100

Siemens X-Ray Equipment Servicer's Technical Forum

January 27, 2015, 09:18:25 PM

Welcome, Guest. Please login or register.Did you miss your activation email?

Forever Login

Login with username, password and session length

News: The New (and improved) Siemens X-Ray Equipment Servicer's Technical Forum. More features, moreinformation and more help for Siemens Imaging Equipment service providers and support persons. Search

HOME HELP SEARCH LOGIN REGISTER

Siemens X-Ray Equipment Servicer's Technical Forum > Siemens X-Ray > ICONOS R 100 / R 200 > Error Massages Iconos R 100 ( step by step )

Pages: [1] previous next

PRINT

Author Topic: Error Massages Iconos R 100 ( step by step ) (Read 3733 times)

tplink11Sr. Member

Posts: 22

Error Massages Iconos R 100 ( step by step ) on: January 05, 2013, 01:30:11 PM

Error list of XCU ( AP-ID 240 )

XCU (AP-ID 240) error # 000

XCU - DOWNLOAD TASK

Internal SW-error: system call failed. A Timer or setting an event flag did not work. A function of the above mentioned taskreturned a fatal error. The XCU tries to repeat the function. If this fails, attempt will be repeated three times. If still unsuccessful the system shuts down. In this case thehardware oftheXCU is defective. This error is fatal, there is no work around.[/center]


DOWNLOAD:internal SW problem: error during initialize Task

Use our professional PDF creation service at http://www.htm2pdf.co.uk!

http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=loginhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=registerhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=activatehttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=search;advancedhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=helphttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=searchhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=loginhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=registerhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&board=28.0http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.0http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.0;prev_next=prev#newhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.0;prev_next=next#newhttp://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=printpage;topic=418.0http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=profile;u=14560http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=profile;u=14560http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.msg1451#msg1451http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.msg1451#msg1451http://www.htm2pdf.co.ukhttp://www.htm2pdf.co.uk


Internal SW problem: error during receiving telegram. A telegramm that has been received in the dual port RAM of D320 orD200 has released an interrupt but cannot be read. Maybe defective D320 or D200.


Internal SW problem: error during sending telegram. This error is caused by sending an telegram while the ARCNET is busy.If there is no positive feedback in between 1 second, the error will be logged. The telegram will then be sent a second time. There is no work around.


No function available for telegram received. An unknown telegram has been received. The function will not beexecuted.[/center]


Invalid Telegram parameter. The Telegram parameter is out of range or the telegramm length anounced in telegrammismatches the real telegram length or the parameter in telegramm has no correspondent bit in the config data base. No work around.


Stand does not confirm requested system mode

The system mode, that the XCU is demanding is not confirmed by the gantry or the stand in between a timeout of 5seconds. In particular this could be:SIRESKOP CX: the position of the tube is not set to the selected target (e.g. the tube is pointing to a spot film devicewhile the wall stand has been selected by the user)ICONOS R100: tomo mode is selected but tomo cannot be set at the gantry because tomo is not possible because the SIDis not in the position where tomo is possible or the room height is limited below the value where tomo is allowed.

SIRESKOP SX: Another reason is, that the Spotfilm device is in park position but spot film device is selected by the user.What to do: Put the tube manually in the correct position or select the correct SID or put the SFD in the correct position.


http://www.htm2pdf.co.ukhttp://www.htm2pdf.co.uk

If the room height is set wrong, the service technician must enter in service mode another value.


No organ program found for selection on desk

No organ program data found for selected organ


XCU - DOWNLOAD TASK

Internal SW problem: System call returned illegal value


XCU - DOWNLOAD TASK

Internal SW problem: error during initializing telegram receive. The XCU cannot access the task processing telegrams.There is no workaround.


XCU - DOWNLOAD TASK

Internal SW problem: error during receiving telegram. See error 002


XCU - DOWNLOAD TASK

Internal SW problem: error during sending telegram, see error 003


XCU - DOWNLOAD TASK



no function availabe for telegram received, see error 004


XCU - DOWNLOAD TASK

Invalid Telegram parameter, see error 005


XCU - DOWNLOAD TASK

Internal SW problem: unable to create alarm time


XCU - DOWNLOAD TASK

Internal SW problem: unable to delete alarm time


Remote Service

The Remote Service Access is set to permanent access by the user. This means a service technician can login remotelyany time the X-ray system is alive.


Remote Service

The Remote Service Access is set to temporary access by the user. This means, a service technician can login remotelyas long as the system will be powered off the next time. The next turn of the system will reset the remote acess state to denied.


Remote Service

The Remote Service Access is set to denied access by user. This means, a service technician cannot login remotelyUse our professional PDF creation service at http://www.htm2pdf.co.uk!



XCU - DOWNLOAD TASK



XCU: Tube load calculator Simulation off

These messages (26 = OFF, 27 = ON) are displayed in order to tell the user, that he now can demonstrate the function(audible alarm and percentage display) of the tubeload calculator without doing a real exposure. To get this message, you have to do the following:

- Turn off SS (Safety Switch of Polydoros SX) - Select a system, where 2-pnt-technique is allowed (e.g. bed exposure)- Select organ program at the lower right corner of the desk (line 5 and column 5). If there is no program programmed onthis location, press the PROGRAM button on the desk. Then it is possible to select also an program by pressing the 5/5 button and the DATA button..- Press the telephone button on the desk. Now you will see instead of the remote access message the message: Tubeload calculator simulation (%HU) ON.

- Wait until this message is cleared by itself (app. 3 seconds)- Set the desired data (e.g. 125 kV and 400 mA)- Press the exposure release button - Wait for spin-up of tube plus an additional second- Release exposure button

- Watch HU display. The HU display should be increased. For getting a feeling, how kV and mAs influences the HU display,look on this example: Tube: OPTITOPMax HU: 580 000 J (= 580 kWs)Voltage: 125 kVmAs 400 mAsEnergy of that exposure: 125kV x 0,4 As = 50kJ.Amount %HU: 50kJ / 580 kJ = 8,6%.

As soon as either another organ program is selected, or SS is turned on or the Telephone button is pressed a second time,the simulation is turned off.Now it is possible to demonstrate the tube load calculator without stressing the tube.Remark: It is not possible to reset the calculator. If it is one heated up no matter if by real exposures or by the simulation,you must wait the amount of time that is necessary to cool down the tube.




XCU: Tube load calculator Simulation offsee Error 26 for details.


Remote Service

The Remote Service Access is set to temporary full access by the user. This means, a service technician can loginremotely as long as the system will be powered off the next time. The next turn of the system will reset the remote acess state to denied. Full access means, that the servicetechnician is allowed to invoke the service of the fluorospot top without assistance of the user


Remote Service

The Remote Service Access is set to permanent full access by the user. This means a service technician can loginremotely any time the X-ray system is alive. Full access means, that the service technician is allowed to invoke the service of the fluorospot top without assistance of the user


XCU - ARCNET TASK

Reconfiguration of ARCNET

---This error is equivalent to the display on D320/D200 of XCU ---

ARCNET low level network has reported an error. The reset of the ARCNET (forced by any other partner in the ARCNET) hasbeen. This error occurs-

if an arcnet controller (D350 of FL TOP, ASU, Generator ...) has been reset by itself or because it is not responding andhas been reset by the network

The error is always created if an imaging system (Fluorospot TOP, Fluorospot Compact, RADIS) has been turned on whilethe other components of the system are already alive. The error may than occur more than once in a row.



Last Edit: January 07, 2013, 11:00:42 AM by tplink11 Logged

tplink11Sr. Member

Posts: 22

Re: Error Massages Iconos R 100 ( step by step ) Reply #1 on: January 06, 2013, 10:24:53 AM



XCU - ARCNET TASK

---This error is equivalent to the display or on D320/D200 of XCU ---

Telegramm transmission error (too short or too long)An ARCNET partner, but not the XCU has sent a telegram violating the telegram conventions 508 bytes. Thespecific telegram will be ignored. There is no work-around.


XCU - ARCNET TASK


Object is in unknown modeAn ARCNET partner has sent a telegram violating the convention for range of parameter telegram type. No work aroundpossible. The telegram will be ignored.

XCU (AP-ID 240) error # 036 XCU - ARCNET TASK

Low Battery


http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=profile;u=14560http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&action=profile;u=14560http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.msg1452#msg1452http://smstechforum.com/index.php?PHPSESSID=nphirfm375h5a5kq7t4pvpbri7&topic=418.msg1452#msg1452http://www.htm2pdf.co.ukhttp://www.htm2pdf.co.uk

This message is created, when during power on the XCU states that the time/date setting is obsolete. Another indicator is,that in this case the date (to be checked by calling the service SW and enter ) is set to 01-MAR-1999.

ReasonBattery on slot CPU = SX control unit (P/N 58 95 292 only, not CPU-HD unit) is empty, not completely inserted or missing.

ActionRemove cover of XCU. Search for slot CPU, which is located on the fourth (the utmost right) slot. Look for Battery which isa inches by 1 inch integrated circuit having four pins. The print on the cover shows and . It is located between the four red LEDsand the plug from the power supply, having lots of coloured wires.

- Is a battery inserted? --> if not, look for it in the housing of the XCU. If found, insert it. The marking (white dot oncover of battery, located on the lower left, should point in direction of HDD/Floppy cabling) and the battery is placed over an IC on the slot CPU.if not found order a new one. (Battery type: M4T32-BR12SH1 from ST Microelectronics (www.st.com)).The only restriction without battery is, that the time/date is wrong. All other functions should work properly.

- is battery tightened, if not, re-insert

remove battery- check for PINs. Are all PINs OK or is one or more broken or bended?- is voltage OK? The voltage should be measured between the PINs separated with a small black nose. Nominal voltage is2.8 V, voltage of a new battery is app. 3.4 V. Replace battery is voltage is below 2.0V, malfunctions (invalid date and time settings) apply below 1.0V.


XCU - ARCNET TASK

---This message is equivalent to the display on D320/D200 of XCU ---

Remote Login via Modem. This message is only an indicator that someone has logged into XCU via a Modem. The status is detected by the D320 andis logged even if an unsuitable Service SW is used.



http://www.st.comhttp://www.htm2pdf.co.ukhttp://www.htm2pdf.co.uk

XCU - ARCNET TASK

---This error is equivalent to the display or on D320/D200 of XCU

IN-List error (too long or too short)The IN-List is the list of telegrams any ARCNET conroler wants to receive. In a telegram, that is sent in mode,is not found in the inlist of a controller, the controller will not receive the telegram. That is the way, ARCNET is using, to reduce the number of telegrams received by aspecific component.The maximum amount in the complete ARCNET (summary of all controllers) is 248 telegrams. If another ARCNET controllerdetects, that are more than 248 telegrams in the inlist or the number of anounced telegrams to be in the inlist is not equal to the number sent, this error will be created.If 248 are exceeded, the controller will not receive all telegrams, this is fatal. However, there is no workaround for a service technician, the problem can only be fixedby the developper of the SW


Power Fail detected

Power fail detected although the power supply has not been turned off.This means that the power supply (AC line) has been interrupted for at least 50 ms up 1.5 sec. (After 1.5 sec the XCUpower supply has no more energy and will terminate and cannot enter the error in the errorlog data base.)This may be caused by the customer by rapidly turning off and on or by interferencies on D160 board or by a bad emergency power supply, that requires several 10 ms to take over energy supply.

If this happens, the errorlog may show several unexplainable errors, because the components are confused. Due to powerfail for some time, the memory gets mixed, but the power on reset will not get active because interrupt was too short.

In order to find out, whether the system is working properly, you may check power fail by unplugging X1 on D320 whilesystem is running. D320 should light up in ist HEX-Display and the error 39/240 should be entered in errorlog. If not either D160 or D320/D200 or cabling is defective. ForD200 it is not easy to unplug, because X1 is also supplying the 5 V to the D200. If you want to check, you have unplug Pin 2 when system is running. (Pin 2 must beconnected during start-up)

XCU (AP-ID 240) error # 040Use our professional PDF creation service at http://www.htm2pdf.co.uk!


XCU - POWER ON

This message is always created when the High End XCU is turned on in order to find out, whether specific errors have beenoccured once or many times before the system has been turned off. The Power on message is created when all components are alive and the system is ready (first systemselection button on the control console lights up) or if the system does not get ready in between this time-out - after 120 seconds. Any time an imaging system (RADISor FL TOP or FL Comp [with the exception of FL H, which is fast enough]) is in the current site, the 120 sec timeout will hit.


ENTER SERVICE MODE

This message is always created when the service PC logs in the XCU. So you may find out, if specific errors occur only inservice mode. No error, for information only.


TERMINATE SERVICE MODE

This message is always created when the service PC logs OUT the XCU. So you may find out, if specific errors occur only inservice mode. No error, for information only.


XCU - ARCNET TASK


This means that, D200 or D320 do not detect an ARCNET carrier signal. This may be caused by many various things:

causes:

No ARCNET wiring plugged incheck ARCNET wiring of XCU

Short circuit on a wire or a Hybrid circuit of an ARCNET partner.If both signal wires are touching each other or touching ground or the input transistor or the hybrid is defective you will set



the 43 (= 31 on display).

Missing terminal resistor or double terminal resistorAny missing or double fitter termination resistior (120 Ohm) will cause an intermitting problem of error 43 (= 31 on D320). Inmost cases the system will run. And sometimes not. Check resistors carefully.

SX generator control consol is set to DUEPThe SX-desk may also be used in Polydoros SX 50 (RAS generator). If the switch setting is wrong, the 43 may be a follow-up error

Jumper X5 in Videomed SX D16 is in position END and termination resistor at XCS.X22 of Videomed SX is fitted

Unsuitable ARCNET chipCheck all listed High-Level-ARCNET-Controller (D100 in FL Comp, D100 in Optix, D16 in Vid SX, D320 in XCU, D200 in XCU,D350 in FL TOP, D100 in FL H, D7 Sireskop SX und D100 in XCU of Iconos R200 and FD thorax/multix) that there is the correct ARCNET Chip Com20020 TypB. If Rev C is found replace immediately the board

Com 20020 Rev CType C is a revision of Com 20020, that has been manufactured for 3 months until an error in the circuitry was reported bythe customer. The manufacturer SMC decided to clear all stocks from Rev C and replace Rev B and the defective "no longer exisiting" Rev C by a Rev D. Rev D is notreleased by MED. Although all stocks should have been cleared from REV C, some distributors sold their samples as Rev B.

Identification of a Rev C Com20020Rev C may be identified on the Chip manufactured by SMC, by a "C" in front of the lot-number. First line on the chip is"SMC", second line is "Com 20020", third line is "C" followed by a number identifying date code and lot number for instance "129020". Rev B will read in the third line "B" +number - OR - number + "B" + number.

Examples: (the red one ist not OK!)

SMC SMC SMCCom20020 Com20020 Com20020 C129020 B234190 3B24907


XCU - ARCNET TASKUse our professional PDF creation service at http://www.htm2pdf.co.uk!



Duplicate node - IDTwo ARCNET partner do have the same physical board adress. This may be caused by jumper setting. Which Partner hasthe wrong ID can be checked by the tool usrshell.exe on this SSW.


XCU - ARCNET TASK


Repeating transimission - parity error

An ARCNET package could not be sent in between the timeout given by the host program and has to be repeated. Thiserror can be ignored. It only indicates that the transmission took more time, than estimated by the developper of the program. If the error occurs very often in a row itmight indicate, that the controller is too busy.


ENTER REMOTE SERVICE MODE

This message is always created when the service PC logs in the XCU via Modem. So you may find out, if specific errorsoccur only in service mode. No error, for information only.


TERMINATE REMOTE SERVICE MODE

This message is always created when the service PC logs OUT after a REMOTE session. So you may find out, if specificerrors occur only in service mode. No error, for information only.


XCU - FD-TASK

Internal SW problem: Systemcall returned illegal value, see error 000Use our professional PDF creation service at http://www.htm2pdf.co.uk!



XCU - FD-TASK

Internal SW problem: error during initializing telegram receive


XCU - FD-TASK



XCU - FD-TASK

Internal SW problem: error during sending telegram. See error 003


XCU - FD-TASK

No function availabe for telegram received, see error 004


XCU - FD-TASK



XCU - FD-TASK





XCU - FD-TASK



XCU - FD-TASK



XCU - FD-TASK

Acquisitions are blocked, because start up offset running. If the user tries to make an exposure during the offsetcalibration this error is created and the exposure is denied.


XCU - FD-TASK

Acq blocked, FD in transparent modeExpsoure and calibration are locked, because the FD is in transparent mode. The transparent mode is a service setting,where the detector can directly talk to RADIS and bypasses the XCU.


XCU - FD-TASK

File cannot be deleted. No further consequences.

Causes: - disk of XCU defective --> replace XCU- disk of XCU is cross-linked because power fail signal (D320/X1) is not working (see error 039) properly and disk is turnedoff during write. You may insert a VGA graphic card into XCU and try to perform per bootable floppy a DOS scandisk to repair. Also you should check the operationof the power fail- disk is full, which might be caused by starting a telegram trace via service PC, that has become too large, so that thedisk is full. Start another trace and terminate it immediately, so that the new trace file is shorter.



- SW error --> no workaround


XCU - FD-TASK

File cannot be renamed. No further consequences. Possible causes


XCU - FD-TASK

File cannot be created. No further consequences. Possible causes


XCU - FD-TASK

File cannot be read. No further consequences. Possible causes


XCU - FD-TASK

Calibration request. The XCU requests the user to perform a calibration, because the calibration inverval has expired.


XCU - FD-TASK

Error during calibration, not enough images. The calibtration has been terminated (by user oder by an error) before the required number of images has been reached.


XCU - FD-TASK

Please wait for RADIS to get ready

Exposure release is blocked, because imaging system RADIS does not send the status as ready for exposure. This may beUse our professional PDF creation service at http://www.htm2pdf.co.uk!


caused by serveral reasons:

- RADIS in not (yet) ready with booting --> wait for end of boot- RADIS is in service mode --> terminate RADIS service session- no patient selected ---> select a patient- RADIS is suffering from an internal problem and will not release the exposure ---> check RADIS error conditions. If noerror appears, restart RADIS.- The calculation of the last image is still in progress. ---> Wait for end of calculation- The offset calibration is currently active ---> Wat for end of calculation


XCU - FD-TASK

Offset calibration in progress

Exposure release is blocked, because offset calibration is in progress ---> Wait for end of offset calibration


XCU - FD-TASK

Wait 2 s before releasing next exposure.

This message indicates, that X-ray release switch has been pushed twice in between 2 secondes. For usual FD systemsdo not accept several demands for exposures in short period of time. Therefore the XCU locks the demand for seconds after the last OFF for exposure. Causes:

- User is gambling with the exposure release switch ---> stop him from doing that- Switch or cabeling of swich is defective ---> replace X-ray release switch

Logged

tplink11Sr. Member

Posts: 22






XCU - BVFS CONTROL TASK

Internal SW problem: System call returned illegal value.See error 000


XCU - BV-FS / VIDEO CONTROL TASK:

Internal SW problem: error during initialize Task









No function availabe for telegram received., see error 004



GENERALInvalid telegram parameter for organ programs or fluoro

SPECIFIC

1. Reason: Invalid Fluorospot H organ program selectedReason: Videomed DI with SW VA02C or below and the afterflash option ist programmed



If the user selects on the generator desk or on the Optix an organ program, which is empty in the FL H memory, this iserror is logged. If the service PC is connected to XCU, it also will be displayed on the desk.

Reason:The Fluorospot H cannot send exposure data, because there are no data programed.Action:2.Select the organ program, Press PAT DIR on FL H, F5 for tools, F1 for Organ Program, enter the specific data in the FL Hand store the program using F2.

2. Deinstall the after flash option in Configure Site Structure: In component selection click the Videomed DI, then clickOPTION and configure NO for the after flash









Illegal Configuration. The Configuration of meas. fileds, TV Parameter oder LTI moder are inconsistent. This error is causedfor instance, if the configuration excludes image freq. 7.5 i/s for pulse fluoro and FL TOP selects the frequency via Organ program.



Videomed does not confirm image flip command

The user has pressed the button for image flip and the camera does not confirm that it did flip the image. The error iscleared automatically, if the error condition is



cleared.

Reason:Software or timing error in the camera.Action:Check SW version of camera and the corresponding XCS-Interface



No confirmation of image flip command in between on second. (If the confirmation is received afterwards, the error isdeleted automatically.)



Horizontal image flip in progress. (If the confirmation is received , the error is deleted automatically.



Videomed does not confirm horizontal image flip command

The user has pressed the button for image flip and the camera does not confirm that it did flip the image.

Reason:Software or timing error in the camera.

Action:Check SW version of camera and the corresponding XCS-Interface



Videomed DI or DIC does not confirm AVR command

The generator has reached the maximum voltage output and wants the camera to take over the AVR. However the cameradoes not reply. The error will interrupt fluoro.



As soon as the error has been confirmed by the user, fluoro is possible but only with 110 kV. The system must be switchedoff and on to restore fluoro funtionality.

Reason:Software or timing error in the camera.

Action:Check SW version of camera and the corresponding XCS-InterfaceCycle power of system.


XCU - GERTEGEOMETRIE/TABLE CONTROL TASK:

Internal SW problem: Systemcall returned illegal value, see error 000












No function available for telegram received, see error 004








Illegal Configuration prob. mismatching service-SW: Brakes, Tomo angles or time



Internal SW problem: illegal parameter in subroutine-call



Internal SW problem: preparation of acquisition not possible

Logged

tplink11Sr. Member

Posts: 22




XCU - CASSETTE CONTROL TASK:

Internal SW problem: Systemcall returned illegal value.See error 000














No function availabe for telegram received., see error 004






Illegal Configuration: Number of possible subdivisions is invalid or number cass progs is invalid



Internal SW problem: illegal parameter in subroutine-callUse our professional PDF creation service at http://www.htm2pdf.co.uk!




Cassette system not responding or not configured



Invalid function ID when changing function circuit



All images exposedThe user has tried to do extra exposures although all images on the cassette film have been exposed.ReasonNo more free imagesAction:Put in a new film in the cassette



No cassette inserted. This Message is created if a the attempt is made to expose, although no cassette is inserted or thecasstte is already exposed.



Cassette locks acquisition: - The cassette is not completely inserted --> remove cassette (might also happen in DR)- Cassette has no more free images ---> insert new cassette- Cassette is not inserted --> insert new cassette- Cassette has been in stand during power up ---> remove and re-insert cassette





Cassette blocks fluoro

ReasonA cassette is in the X-ray beam and would be exposed, if the fluoro is turned on.Action:Remove the cassette


XCU - GENERATOR CONTROL TASK:

Internal SW problem: System call returned illegal value, see error 000








XCU - STRAHLUNGSERZEUGUNGS/GENERATOR CONTROL TASK:









Invalid Telegram parameter, see error 005This error is logged only. There is no work around but also no harm to the system. However one of the components doesnot obey the telegram rules.In FD systems this error will occur permanently after each acquisition, due to the telegram sBedGen to reset the diamentormemory in the XCU. The memory is reset, but the choosen parameter is wrong.



Illegal Configuration: exposure curves, tube data etc.






Acquisition blocked due to invalid feed back of selected tube.



Preparation of acquistion not possible


XCU - GENERATOR CONTROL TASK:Use our professional PDF creation service at http://www.htm2pdf.co.uk!


Acquistion blocked due to limit. The Limit (exposure has been terminated by generator due exceeding value for max ms ormax mAs) condition is on and MUST be confirmed by the user BEFORE continuing with an exposure.



X-ray blocked



Preparation of X-ray not possible



Active tube is not the selected tube. Generator selects another tube than the desired one. Acq are disabled now.



Internal SW problem with finding values in a table of the tube. When transforming normal value to BP there is the need of tables. If a value outside a table has to be found, this error is created. In most cases it is harmless and may be ignored.



Internals SW error: wrong value in constant


XCU - GENERATOR CONTROL TASK:Use our professional PDF creation service at http://www.htm2pdf.co.uk!


Internal SW error: exp. value (BP) < 0. May be ignored. No further consequences.



Internal SW error: water equivale t value in BP is below 0. Probably the water equivalent calibtration has not been donecarefully.



Internal SW error: water equivalent value in BP is above Maximum. Probably the water equivalent calibtration has not beendone carefully.



No grid correction value for selected grid. This error is caused by a wrong configuration. Somebody removed the grids inthe site structure dialog but the grid is still in the system. As soon as it selected by organ program or manually this error is created. The error is internally ignored and theXCU assumes no grid.The error is only a problem if the fluoro is done without and the exposure is done with grid. You may solve the problem inthe site structure by clicking on the stand (Polystar, Iconos, Sireskop, Siregraph ...) and click edit and set the grid to .



No filter correction value for selected filter. This error is caused by a wrong configuration. Somebody removed the filters inthe site structure dialog but the filters are still in the system. As soon as it is selected by organ program or manually this error is created. The error is internally ignored andthe XCU assumes no filter. You may solve the problem in the site structure by clicking on the stand (polystar, siregraph, sireskop, iconos) and set the filters to.




unknown exposure technique selected. Valid exposure techniques are: DR, Tomo, DSA, Peri, 2-pt, 3 pt .... If a SW selectsanother than a valid technique this error is created.



No exposure curve for selected system. In an organ programm there is an unknown exposure curve selected. For usual C0to C99 are valid. Sometimes also C100. Any other curve will create that error.



Calculated value in exposure table is not OK. The exposure will be blocked.



Wrong value in tube load calculation. Tube data are not ok, XCU continues with default data for a 30 kW tube.



No value for foil sensitivity available. This indicates an invalid configuration of HUD in the site structure (no ionotomatconfigured, but organ program wants an ionotomat technique). Check configuration of OGP and availability of ionotomat in the system (no 1 pt technique program in systemwithout ionotomat.)



No water equivalent table found: no exposure curve for selected system. In an organ programm there is an unknownUse our professional PDF creation service at http://www.htm2pdf.co.uk!


exposure curve selected. For usual C0 to C99 are valid. Sometimes also C100. Any other curve will create that error.






Addition of all exposure points is wrong. Wenn calculating the water equivalent value the checksum is wrong. XCU willcontinue working with almost correct data



No grid data for selected grid. Probably the grid has not been configured. Call configure, select in the component list thestand (e.g. Sireskop or Polystar) and press the EDIT button. The next or next plus one window should show up the grids configuration. Enable the grid checkbox, selectthe grid of your X-ray system and save the configuration

XCU (AP-ID 240) error # 292 / 293 / 294 / 295 /296 /297


An exposure has been terminated by releasing the HK switch or by opening the door while radiation is on. If this error is inthe errorlog and the customer complaints about some films being too bright (under-exposed), the filming was terminated because the X-ray switch has been releasedby the customer before the radiation was terminated.The error also may be a follow-up error of a generator error, caused during radiation is on because the radiation will beterminated by the error and not by Iontomat, mAs-relais or ms - relais.

The error is logged system specific (see table below). The error is logged only for cassette and DR single shots with fixedkV. For DR series the generator will not terminate an exposure in progress before exposing is finished. In DR-0-pt-technique single the generator will terminiate but



will not that error.

The error is logged system specific:292: System 1293: System 2294: System 3295: System 4296: System 5297: System 6-12

Logged

tplink11Sr. Member

Posts: 22




XCU - SYSTEM SELECTION CONTROL TASK:
























Wrong configuration: if a system selection refers to a not configured system number.



Videomed does not confirm image flip command

The user has pressed the button for image flip and the camera does not confirm that it did flip the image. The error iscleared automatically, if the error condition is cleared.

ReasonSoftware or timing error in the camera.Action:



Check SW version of camera and the corresponding XCS-Interface



Internal SW problem: invalid system number



An unknown system number has been selected.



Tube selection has not been confirmed

This error might be caused by a defective starter or a defective cable to the starter. Another indicator of this error mightbe that the generator shows on the D100 the 3.Action: Check cabling.

This error might also be caused

- when Polydoros Service SW is running (Generator is in service mode) and you select another system at the generatordesk. In Service mode the generator does not answer to standard telegrams, so the request for confirmation current tube or changing to new tube will not be answered.

- when the generator will not come up when X-ray system is powered on(due to missing SW on D100, or missing XCS-cabling or XCS network problem) this error will be shown 1 to 2 minutes after power on.


XCU - ORGAN PROGRAM SELECTION CONTROL TASK:























Internal SW problem: unable to delete alarm timeUse our professional PDF creation service at http://www.htm2pdf.co.uk!




Internal SW problem: timeout during communication



Organ program memory is full

In the Polydoros LX/lite only 125, in the SX only 990 organ programs can be stored.

ReasonSomebody has tried to store more then the possible max number of organ programsAction:Another organ program has to be deleted to store the new one



Illegal Configuration, the error might derive from the attempt of the user, to store an OGP in the FL Comp, while the systemselection is set to bucky, cassette ...






Error writing to HD, probably HD of XCU defective or cross-linked. Possible causes




Invalid organ program, technique not allowed in system



Error during storing organ program to disk. Possible causes



Invalid organ or region in organoperationThis error might be caused, if the organ option has not been set or if not all regions have been defined in the service SW.Corrective Action: Enter site structure configuration, set in site adjustment dialog the organ option to available (if thecustomer has ordere OGPs) and set all 12 regions by pressing the ADD REGION button. It is not necessary to enter names for the region with the exception of Sireskop SX.



Save operation of organ programs not completed. During saving an organ program, which lasts for about a second, the userattempts to store the next organ program.



DFR organ without DFR option set. Problem fix: Call configure site structure on service PC, confirm all dialogs with OK andsave the configuration. This should cure the problem.



DFR organ block without DFR mark set in parent organ program. Problem fix: Call configure site structure on service PC,Use our professional PDF creation service at http://www.htm2pdf.co.uk!


confirm all dialogs with OK and save the configuration. This should cure the problem.



Organ program for table specific parameters without init data 66. Problem fix: Call configure site structure on service PC,confirm all dialogs with OK and save the configuration. This should cure the problem.



Organ program for stand without main organ program. Problem fix: Call configure site structure on service PC, confirm alldialogs with OK and save the configuration. This should cure the problem.



Organ program not stored because organ data are kept external. This error will happen, if a FL H imaging system isconfigured, but a FL TOP or FL Compact organ storing operation is done.



Table specific organ data not stored because no main organ program. Problem fix: Call configure site structure on servicePC, confirm all dialogs with OK and save the configuration. This should cure the problem.



Organ data mismatches system type. After acknowledging this message by the user the exposure will be done using defaultdata. This error is caused especially in service



IQAP or IMAC, if a system selection is done while IQAP is active and IQAP saves an OGP for DR although DR tomo is nowactive.



Organ programming is disabled because the system has been configured or a restore has been performed and since theconfiguration the XCU has not been booted. Boot the XCU by cycling power. OGP programming will then be allowed. The reason for that behavior is, that the configuration is storing a new OGP structure to disk and the copy of the disk inthe RAM of the XCU is no longer a real copy. If someone now store OGP Nr. 7 this OGP might be on location 5 on disk. And what would happen is, that the XCU places thedata for OGP 7 on the space of OGP 5 on the disk. Because Nr. 5 can also be in another system (e.g. Cassette tomo instead of the DR standard) the consequenceswould be fatal. Therefore storing OGP is not allowed, if configuration has been made through.

Because IRIS adjust, IQAP and IMAC of FL TOP are doing also an OGP store, IQAP and IMAC are not possible, as soon asthe configuration has been entered.If the XCU powers on, the OGP on disk are completely copied to the RAM and everything is fine again.

Logged

tplink11Sr. Member

Posts: 22




XCU - EXPOSURE TASK:























XCU - EXPOSURE TASK



XCU - EXPOSURE TASK:Use our professional PDF creation service at http://www.htm2pdf.co.uk!


Illegal configuration



Acquisition not possible because a component is not ready: The system is not ready for exposure because one or morecomponents are no longer ready. This error is also caused, if a spotfilm device is parked or a 3D stand is not in park position.



Acquisition is prohibited by generator

May be caused by:

- a tube selection is in progress (up to 8 sec after a system selection) --> wait- door contact is open (door is not closed) --> close door or shorten contact if no door is present- generator is in service mode and an acquisition should be released at the console ---> leave service mode on servicePC)- generator is in limit function (acquistion has been terminated due to exceeding max time or max mAs) ---> confirm limiton console

- X-ray disable switch is activated ---> close x-ray disable switch or if no disable switch is present, make sure that D160and D320 in generator do match (both new or both old) and that the X-ray disable input is set to enable X-ray- contact is closed ---> wait until emergency power is replaced by regular power or if no emergencypower is available, make sure that D160 and D320 in generator do match (both new or both old) and that the emergency input is set to

- An error of the generator of the filament or of the iontomat (e.g. error 550of AP ID 80has been confirmed by the userand the generator has reset filament or iontomat which lasts up to 10 seconds. If an acquistion is requested in between this time, this error is displayed.- In case of LX, that may mean that simple DR has been selected by switching to organ program #1 in region 1 but therewas no preceeding fluoro before invoking the exposure.


XCU - EXPOSURE TASK:Use our professional PDF creation service at http://www.htm2pdf.co.uk!


Acquisition is blocked by cassette.

- The cassette is not completely inserted --> remove cassette (might also happen in DR)- Cassette has no more free images ---> insert new cassette- Cassette is not inserted --> insert new cassette- Cassette has been in stand during power up ---> remove and re-insert cassette



Acquisition blocked by collimator, grid or filter.Caused by:

- Collimator is searching for zero position- Collimator is re-collimating and closing completely- Grid has been moved right before beginning exp. and did not reach the final position. - Collimator does not reach its final position --> problem in collimator Hardware

First three possible error causes should be cleared automatically after 1 - 2 seconds. Last cause will not cure.



Acquisition blocked by invalid device / Stand position. The device for Peri or Tomo is not in the correct position or the userdid not perform fluoro before starting peri.


same as 420


same as 421


same as 422




same as 423


same as 424


same as 421


same as 422


same as 423


same as 424


same as 421


same as 422


same as 431




same as 432


same as 433


same as 434


same as 423


same as 424


same as 421


same as 422


same as 423


same as 424



same as 421


same as 422


same as 423


same as 424


same as 421


same as 422


same as 423


same as 424


same as 421




same as 422


same as 423


same as 424


same as 421


same as 422


same as 423


same as 424



Acquisition blocked by DFRThis may be caused by conditions:

- no patient selected- no more memory available on DFR- storing of images in progress- deleting of images in progress- imaging system is in error condition- background job is being prepared



- the last acquitition has been terminated only 1.5 seconds before (recovery time)


same as 462


same as 462


same as 462


same as 462


same as 462


same as 462


same as 462


same as 462


same as 462 Use our professional PDF creation service at http://www.htm2pdf.co.uk!




same as 420


same as 420



Fluoro turned on during exposure. The generator denied turning off the fluoro for beginning next exposure. The error iscured with the next fluoro.



Acquisition blocked by FD-Detector . The FD detector is not ready for acquisition. It will take a long time until this messageis generated, because there is no Telegram for the FD to say not ready. The only way to say not ready is to net say ready.


same as 475


same as 475


same as 475





The organ program contains only default data, has never been stored by the customer. The acquisition is blocked. Fix theerror by storing the organ program at the Fluorospot. This message has been inserted for safety reasons. Because it is possible to store an organ program name fromthe control console without organ data for DR systems, the user might be confused if he is using the organ program with a name called DSA but will get default datainstead of DSA parameters. Therefore acquisition is blocked.



Exposure blocked by RADISRADIS does not allow an acquisition.

Reasons:- no patient selected- no organ program selected- still engaged with reading image data- still booting


same as 480

Last Edit: January 15, 2013, 05:17:35 AM by tplink11 Logged

tplink11Sr. Member

Posts: 22




XCU - FLUORO CONTROL TASK:





XCU - DURCHLEUCHTUNG / FLUORO CONTROL TASK:













1.) invalid Telegram parameter, see error 005

2.) This error might occur, if the user selects in a Fluorospot TOP organ program a fluoro program that has not beenconfigured for pulsed, but the user selects for this specific program the pulsed property.



To get rid of this problem: configure the specific program with pulsed fluoro in CONFIGURE of the XCS SSW



illegal configuration. invalid fluoro curves etc.



The generator blocks fluoro because

- door is open- X-ray disable swich is on- tube switching is in progress after a system selection (takes about 8 sec for heating up the tube)- problems with its hardware- limit is not confirmed by the user



Gantry or stand position blocks fluoro

ReasonsThe Spotfilm device is in park position and II is not in one line with the tube.The SID of Iconos R100 is not at one of its marked positions.Action:Put the device in the correct position or put the SID to the end.



FLUORO blocked by TV or Image Flip.





FLUORO blocked by Cassette. (Cassette or cassette device would be in fluoro image, because cassette is not completelyinserted). Insert cassette completely or remove cassette



Collimator blocks fluoro

ReasonFluoro cannot be released, because the collimators do not send the telegram that they have reached theif final position.The collimator may only block fluoro, if the fixed size diaphragmas are moving so that they cover all of the image or if the collimator is doing a seach for its zero position(will be performed once per hour). The error should be cured by itself after app. 2 seconds.

Action:Check the collimators mechanically if they have been problems in movingCheck the grid, if there is a problem with the switch or the reversing



The generator blocks fluoro because

- door is open- X-ray disable swich is on- tube switching is in progress (takes about 10 sec for heating ab the tube)- problems with its hardware- Limit has not been confirmed





FLUORO blocked due to Component fatal Error.



FLUORO blocked because maximum Fluoro time has been exceeded. Bell for short time reset or 0-button on generator deskfor long time reset has to be pressed or re-release Flouoro-Switch



FLUORO blocked because X-ray disable switch is ON.

This signal is generated by the D320/D160. So it also may be caused by a problem in the cabling of those boards or byusing not matching samples of these two boards.


XCU - COLLIMATOR CONTROL TASK:


















Invalid Telegram parameter, see error 005For instance in Telegram iBlende the collimator angle is below 0.1 or above 360 or the coll nr is above 6,



COLLIMATOR Task: error creating alarm



COLLIMATOR: error deleting alarm




Illegal configuration. This error is caused for instance, if an organ program requires a copper filter although no filters areconfigured in site structure. Configure these filters by calling site structure, click the stand (Polystar, Sireskop, Iconos ...), click edit and say in filter:available.






Auto filter has been selected by the user or by organ program but there are no filters configured. Configure these filters bycalling site structure, click the stand (Polystar, Sireskop, Iconos ...), click edit and say in filter: available.

Logged

tplink11Sr. Member

Posts: 22

Re: Error Massages Iconos R 100 ( step by step ) Reply #7 on: January 26, 2013, 08:12:03 PM



XCU - SERVICE PC COMMUNICATION TASK:















Invalid Telegram parameter in a service telegram. Invalid telegram length or invalid group-id.



No timer for remote display choice availableIf this error happens, the remote service access choices will not be displayed on the control console.



Internal SW problem: not enough memory



Illegal Configuration. This error is normal in a system that is not yet configured





Error of init block 2 (system data)



Error of init block 3



Error copying data to HD






Error of init block 57-64
















Error copying data to HD. Possible causes























Error of init block 48, 94
















Causes: - disk of XCU defective --> replace XCU- disk of XCU is cross-linked because power fail signal (D320/X1) is not working (see error 039) properly and disk is turnedoff during write. You may insert a VGA graphic card into XCU and try to perform per bootable floppy a DOS scandisk to repair. Also you should check the operationof the power fail



- disk is full, which might be caused by starting a telegram trace via service PC, that has become too large, so that thedisk is full. Start another trace and terminate it immediately, so that the new trace file is shorter.












Error of init block 50 (Tubus)










Error writing init block 1 to HD. Possible causes





Error of init block 52 (cassette data)



Error copying init block 52 to HD. Possible causes



Causes: - disk of XCU defective --> replace XCU- disk of XCU is cross-linked because power fail signal (D320/X1) is not working (see error 039) properly and disk is turnedoff during write. You may insert a VGA graphic card into XCU and try to perform per bootable floppy a DOS scandisk to repair. Also you should check the operationof the power fail- disk is full, which might be caused by starting a telegram trace via service PC, that has become too large, so that thedisk is full. Start another trace and terminate it immedi

Error Codes R100

Documents