EP-25 ERA PRESS

CML International S.p.A.Piedimonte S. Germano (FR)Italy

EP25 ENGLISH INSTRUCTIONS MANUAL R2.1 27 02 03 1

EERRAAPPRREESSSSEEPP2255--VVSS

Hardware ver.: 0.0.ASoftware ver.: EP102Man.Rel.: 2:1



CONTENTS

1. GENERAL SAFETY WARNINGS ........................................................................................................ 3

2. ELECTRONIC CARD ............................................................................................................................. 5

3. CONTROL PANEL .................................................................................................................................. 6

4. EMERGENCY STOP AND RESET ....................................................................................................... 7

5. START UP OF MACHINE ...................................................................................................................... 8

6. OPERATION MODE SELECTION ...................................................................................................... 8

7. TOOLING SELECTION ......................................................................................................................... 9

8. PROGRAMME SELECTION ............................................................................................................... 10

9. HOW TO SET UP PARAMETERS ...................................................................................................... 11

10. WORKING SPEED SELECTION ...................................................................................................... 13

11. HOW TO ZERO JOB CYCLE COUNTER ....................................................................................... 14

12. HOW TO CHANGE HOLDING JAWS ............................................................................................. 15

13. PRESSURE REGULATION ................................................................................................................ 15

14. ELECTRICAL DRAWINGS ............................................................................................................... 16



1. GENERAL SAFETY WARNINGS

BEFORE MACHINE USEWARNINGS AND PRECAUTIONS

This symbol is a danger sign and warns you FOR YOUR SAFETY, that there is highand dangerous tension in the machine.

WARNING!

This signal is a danger sign and warns you FOR YOUR SAFETY that there arefundamental instructions to be followed.

This signal is a danger sign and warns you FOR YOUR SAFETY that there arefundamental instructions to be followed in order to avoid injury, and damage toobjects.

INSTRUCTIONSTo avoid injury, and damage to objects



GENERAL SAFETY NORMS

WARNINGThe ERAPRESS EP25H2-VS has been manufactured according to state-of-the-arttechnology and in compliance with safety regulations officially accepted. Nevertheless themachine can be dangerous for the operator or a third person if used in a improper manner.It is important therefore to read the following safety norms.

WARNING Use the machine only and specifically for the use which it has been manufactured for

and with full respect of the general safety norms. The Manufacturer will not be liable forany injury or damage to objects due to an incorrect use of the machine.

Verify that the line voltage is always compatible with the power supply for which themachine has been manufactured for.

Make sure that only trained personnel operates the machine. Do not use the machine in an environment containing explosive material. Do not use the machine in a humid or wet environment. Do not expose the machine to the rain. Store the machine in a dry and safe place. Keep away unauthorised personnel when the machine is both in motion and switched

off. Do not touch parts in motion. Do not operate on mechanisms in motion. Do not remove or tamper with safety devices. Do not wear loose clothing. Non authorised persons should be prohibited from entering the machines working

area. Go to a safe position when the machine is in use. Never stand next to the machine on the opposite side to the controls. Avoid accidental start of the machine. Electrical repair on the electrical panel of the machine is to be effected only by qualified

personnel. Switch off power supply when operating on the electrical system. Fix the machine to the ground by using the appropriate fixing points. Do not tamper with electrical and electronic circuits in any way for safety reasons and

in order not to invalidate the warranty conditions. Disconnect main power cable prior to transporting the machine. Do not modify the machine structure. Use only era accessories. Any alterations will

cause the invalidation of the warranty. The Manufacturer reserves the right to notsupply accessories or replacement parts in case the machine has been altered.



2. ELECTRONIC CARD

The ERAPRESS EP25H2-VS machine has an electronic card (Fig. 1) which is easy to useand ensures better and safer work.

OPEN : Vice openingCLOSE : Vice closureFORWARD : Tool forwardRETURN : Tool returnMENU/ESC : Menu / Esc scrollENTER : Confirmation

Figure 1 Electronic card.



3. CONTROL PANEL

EMERGENCY : Mushroom head buttonR : Reset buttonCHANGE : Vice jaw change selector.START 1 : Start button 1START 2 : Start button 2

EMERGENCY

R

CHANGEOFF ON

START 2START 1



4. EMERGENCY STOP AND RESET

In dangerous situations for the operators health or if there is risk of breakage of anymechanical component of the machine, press immediately the emergency mushroom headbutton.Such operation interrupts immediately the electrical power supply to the machine and anymotion in course.

When danger has ceased, reset the mushroom head button by turning it in the samedirection of the arrow, in order to reset the normal working conditions of the machine andthen press reset button R.



5. START UP OF MACHINE

The plug of the main power cable can be inserted, after checking the exactcorrespondence between the voltage of the machine and the line voltage.Select 1 (ON) on the main switch near the door of the electrical cabinet for electrical supplyof the machine (each time a working cycle ends, switch off the machine selecting 0 (OFF)on the main switch).Check that the mushroom head emergency button has not been pressed. In case theemergency button is pressed, turn it in the opposite sense to the direction of the arrowuntil resetting it.Press button R ( machine reset ) to supply power to the electrical devices of the machine.

6. OPERATION MODE SELECTION

You can select the operation mode of the machine (press or expander / reducer) bypressing ENTER button for 4 seconds.

The mode selected is indicated by the first letter on the left side of the display (Fig. 2 , 3)

P1 -010.0 061.7



The press mode selection allows only the horizontal cylinder to move. If expander/reducermode is selected, vice opening / closure is allowed too.

7. TOOLING SELECTION

It is possible to effect a working cycle in assist mode or in manual mode.The assist mode allows a complete working cycle according to the selected machineoperation mode ( press or expander/reducer ) by simply pressing at the same time the twoSTART 1 e START 2 buttons, placed on the side of the control panel. (ref. par. 2).The working cycle can be interrupted by releasing one of the two buttons.

The manual operation mode allows the individual movement of each function with fullrespect of the safety standards.

1. TOOL FORWARD: press forward button + START 2 (before FORWARD BUTTON)

2. TOOL RETURN: press return button + START 1 (before RETURN BUTTON)

3. VICE CLOSURE: press close button + START 1 + START 2 (before CLOSE BUTTON)

4. VICE OPENING: press open button + START 1 + START 2 (before OPEN BUTTON)

NB:A complete vice opening and closure under manual mode, can require moreoperations.

NOTE: use the cylinder tool in manual operation mode only for positionreferences during programming and not for job cycles.

WARNING: FOR SAFETY REASONS, keep the protection cover closed duringexpanding / reducing operation mode. If protection casing is open duringexpanding / reducing mode, vice is enabled to open and / or close.



P1 -010.0 061.7



9. HOW TO SET UP PARAMETERS

Before starting a work cycle, it is necessary to set the work parameters , the zeroreference and material reference with the tool.

The zero reference is the starting point from which the tool starts and stops at the end ofa job cycle.

The material zero is the point in which the tool comes into contact with the material .

The penetration level is the distance along which the tool penetrates into the material.

The machine is pre-set by the factory in order that tool moves from zero reference tomaterial zero with high speed, and in order to penetrate into the material with low speedaccording to the programmed level. When the penetration level is reached, the tool goesback to zero reference with high speed.

Select working programme and bring the cylinder to the desired position

as zero reference. Such position is stored by pressing the buttons + (pressfirst RETURN BUTTON).The flashing display confirms position memorisation.

The Material zero point is effected by bringing the tool to the required position and + by

pressing buttons + (FORWARD BUTTON FIRST) for memorisation.

The figure on the right hand of the display should show 000.0 to confirm memorisationhas taken place.

In order to set penetration level, press twice menu / esc button until thefollowing is displayed as evidenced in fig. 5:

zero reference Material zero Penetration level

P1 -010.0 061.7



By using + buttons set the desired value and confirm bypressing ENTER.

Carry out a working cycle with no material to verify that set parameters are correct. Thepenetration level must always be negative.The first value on the right side of the display (Fig. 6) indicates the current position of thetool in relation to zero reference.

P1 -010.0 061.7



10. WORKING SPEED SELECTION

By default the machine is set in order to carry out the working cycle with low speed duringpenetration/ folding phase.However, it is possible to vary such set up so as that tool can move with high speed evenduring penetration/folding phase. Therefore it is important to press the two

buttons +

The high or low speed set up is displayed by the message FAST or SLOW as showed in fig.7 and 8:

P1 -010.0 FAST



11. HOW TO ZERO JOB CYCLE COUNTER

The machine is provided with a job cycle counter indicating the number of work cycleseffected.The registered values are displayed on the right side at the end of each cycle (fig.9).

When a new working cycle is started it is possible to zerothe counter by pressing

P1 -010.0 1



12. HOW TO CHANGE HOLDING JAWS

In order to change the type of vice jaws, proceed in the following manner:

1. Close vice2. Select CHANGE for the holding jaws through position ON and extract key for extra

safety.3. Open vice until it is in position and no motion is possible.4. Change vice jaws .5. Insert key into selector and set OFF position.6. Start working cycle.

When holding jaws are changed, a particular configuration of the electrical circuit blockstool movement and allows the vice to move until change position is reached. After suchchange, any motion of the machine is not enabled until CHANGE selector is set on OFFposition.

13. PRESSURE REGULATION

It is possible to regulate the tool and vice pressure through the pressure regulators of themachine.

On the left side of the electrical panel there is a pressure regulator for the cylinder tool. Onthe right side there is the pressure regulator for the vice.

It is possible to regulate the pressure regulations through the appropriate knobs tooptimise work process.



14. ELECTRICAL DRAWINGS

EP-25 ERA PRESS

Documents

arefundamental instructions

safety regulations

objectscml international

danger sign

tooling selection

programme selection

speed selection

operation mode selection