Der Kollektor E-PVT 2,0 ist eine Kombination von einem Flach Sonnenkollektor mit einem polykristallin PV-Mo- dul mit einer Leistung von 300 W. Der Sonnenkollektor ist verantwortlich für die Verwandlung der Sonnenstrah- lung auf Wärmeenergie zur unterstützung von Warmwasser und Leitungswasser. Das PV-Modul verwandelt Sonnenstrahlung in Elektrizität. Erwärmung von PV-Modulen verringert Ihre Leistung, und wird um c.a 0,5% Ge- ringerer bei zuhname der Temperatur um jedem Grad. Die Leistungscharakteri- stik, die im Technischen Daten angegeben wird, bezieht sich auf eine Modul Temperatur, die 25 ºC beträgt. Durch die Instalation von einen Thermischen System im den Hybrid Kollek- tor PVT erfolgt ein wärme Empfang durch ein Kühlmittel der im den Kollek- tor fließt. Durch den wärme Empfang aus den Thermischen Teil des Kollektor steigt die Elektrische Leistung des PV-Modul. Der Hybrid Kollektor E-PVT 2,0 ist eine Technologische Entwicklung im Bereich von erhöhung der Leistung von PV Modulen bei einer gleichzeitigen verwandlung der Sonnenstrahlener- gie auf Wärme Energie und Elektrizität. Vorteile des Hydbrid Kollektor E-PVT 2,0: » höhere Effizienz der produzierten Elektrischer Energie im vergleich zu standard PV-Modulen, » Thermischer Teil des Sonnenkollektor dient zur erwärmung von Warmwas- ser und zu unterstützung von Heisen Leitungswasser, » Einsparung von Dachfläche und Montagekosten, » höhere ökonomische und wirtschaftliche möglichkeiten – ein Kollektor erzeugt sowohl Strom als auch Wärme, » geringere Investitionskosten der Anlage als bei traditionellen Geräten (Sonnenkollektor und PV-Modul). E-PVT 2,0 +\EULG .ROOHNWRU / K\EULG FROOHFWRU Collector E-PVT 2,0 is a combination of a flat solar col- lector and photovoltaic module with polycrystalline silicon cell with power of 300 W. By bionic exchanger waste heat is used for domestic hot water or central heat- ing, photovoltaic module converts the solar energy into electricity. Photovoltaic module defined as a source of a pure electric energy is not without downsides; its efficiency lowers when the temperature of the module rises. When the temperature of cells goes up by 1 K, its capacity of producing energy goes down by 0,5%. Catalogue parameters of photovoltaic modules are given for the temperature of a module equal 25 degrees, with an insolation of 1000 W/m 2 . During the work in a full, lasting for several hours insola- tion, the temperature of a module rises to a level which could cause the loss of efficiency reaching even 40%. By using thermal system in a hybrid collector PVT occurs a reception of warmth with the use of cooling fluid flowing by Roll-Bond exchanger. By removing the heat, thermal system increases the capacity to process solar radiation into electric current, but also provides a lot of thermal energy. Hybrid collector E-PVT2,0 is a technological progress in in- creasing efficiency of photovoltaic modules with a simultaneous ex- change of a solar energy into thermal and electric energy. Advantages of a hybrid collector E-PVT2,0: » higher efficiency of production of electric energy in compari- son to standard photovoltaic modules, » thermal part of a collector is used for heating domestic water and supporting central heating, » more economic possibilities – one module required for pro- duction of electrical current and heat, » lower investment cost of both systems than in traditional devices (fluid thermal collectors and photovoltaic mod- ules). HERSTELLER von Sonnenkollektoren E-PVT 2,0 | HYBRID KOLLEKTOR