-
Vers
a-M
atic
Solu
tions
◗ Pump Curves, Dimensions& Specifications
◗ Application & Installation Guides
◗ Materials of Construction, Temperature Limits& Wetted
Material Compatibility
◗ Troubleshooting Guide
ESEngineering SpecificationsElima-Matic Pumps, Accessories &
Diaphragms
-
SUBMERGED Versa-Matic Pumps are totally submersible. It is
important that the air exhaust beported above the level of the
fluid, and that the materials of construction also be compatible
with the fluid that the pump is submerged in.
POSITIVE SUCTION For emptying tanks it isimportant to limit the
inlet fluid pressure to approxi-mately 10 PSI (0.69 bar) for PTFE
diaphragms and15 PSI (1.03 bar) for rubber and
thermo-plasticdiaphragms. Greater inlet pressure can cause
erraticpump operation and premature diaphragm failure.
SUCTION LIFT The suction capabilities of eachpump may vary due
to system design, product being pumped, and pump materials of
construction. Please consult the factory with specific
criteria.
2
Applications & Installations
www.versamatic.com
Shut Off Valve
Air Stop Valve/Needle Valve
Filter Separator
Pressure-reducingValve
FluidInlet
Discharge PressureGauge
Manometer
Shut Off Valve
Air Connection
Fluid Discharge
AODD PUMP
Air Exhaust
Air Exhaust Muffler
Pulsation Dampener
Union or Pipe FlangeConnection
Union or Pipe FlangeConnection
FlexibleConnection
FlexibleConnection
FlexibleConnection
SUBMERGED POSITIVESUCTION
SUCTION LIFT
-
3
The Exclusive Elima-Matic® Air Valve SystemAnti-stalling,
Non-icing & Lubrication-free
www.versamatic.com
True to their name, ELIMA-MATIC® pumps virtually eliminate
intermittent pump stalling caused by air valve system freeze-ups.
By utilizing the patentedELIMA-MATIC® anti-stalling, non-icing,
lubrication-free valve system, this common air diaphragm
pumpproblem is a thing of the past.
Eliminating Downtime ELIMA-MATIC® ensures continuous, reliable
pumpperformance. Here’s how it works:
The valve spool is positively shifted by the transfer ofa pilot
shaft. When the main shaft travels to full-stroke length, the inner
piston on the opposite sidedepresses an internal pilot shaft which
ports a burstof compressed air to the main spool valve. The
mainspool valve reciprocates in a positive reliable shift. Asthe
pilot shaft moves back and forth, an air burst isported to the main
spool which causes it to shiftevery time, eliminating stalling.
Losing Your CoolBy evacuating compressed air through air
passages that are designed to allow a controlled expansion,a
considerable reduction in the cooling effect occurs. In addition,
the center block and air valve surface areas are ribbed and act as
heat exchangers to dissipate the rapid cooling effect.
Ease of MaintenanceThe ELIMA-MATIC® not only eliminates freezing
and stalling, but maintenance headaches as well.The ELIMA-MATIC®
has only two easily accessiblecenter block o-rings — some
competitors pumpshave as many as seven. The pilot shaft o-rings
come out as a complete assembly and are easilyreplaced without the
use of an o-ring tool. And the air valve can be worked on without
taking thepump’s center section apart.
Maximizing Pumping PerformanceVersa-Matic pumps can already
handle anything from water to 90% solids easily and efficiently.
Add the ELIMA-MATIC® air valve system and you’vegot a pump that
offers powerhouse performance.
Air Valve Upgrades Also available as a conversion kit for
Versa-Matic V4, V2 and V3 pumps, as well as Wilden® 1 1/4", 2"
and3" metallic pumps, the ELIMA-MATIC® comes witheither an
aluminum, stainless steel, or PTFE-coatedair section. (The air
chambers, air valve and centerblock can be nickel-plated for
diverse applications.)
Available for 1-1/4", 2" and 3" pumps.Consult Versa-Matic or
your local distributor for details.
Elima-Matic® Retro Fit Centersfor V-Series and Wilden® Pumps
Complete Kit Center Section Only(Includes Main Shaft)
-
Suction Port: 1/2" Male NPT,1/4" NPTF
Air Inlet Port:1/4" NPTF
(opposite side)
Discharge Port: 1/2" Male NPT,1/4" NPTF
3/8" [10]Typ. Slot
Optional Horizontal Discharge
.75[19]
.19[5]
7.00[178]
7.06[179]
7.81[198]
6.56[167]
3.44[87]
1.25[32]
1.25[32]
2.63[67]
2.63[67]
3.06[78]
1.31[33]
3.13[79]
5.50[140]
5.25[133]
inches [mm]
E6
4
1/4" Bolted Plastic Pumps
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
0 4 6 8 10 12 14 162
20
40
60
80
100
00 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5.5
Capacity in US Gallons Per Minute
Disc
harg
e He
ad in
PSI
Capacity in Liters Per Minute
Displacement Per Stroke, 0.01 Gal. (0.04 L)Flow Rate adjustable
to . . . . . 0-4 gpm (15 lpm)Port SizeInlet and Discharge . . . . .
. . . . . 0.25" NPTF I.D.. . . . . . . . . . . . . . . . . . . . .
. . 0.50" NPTM O.D.
Air Inlet . . . . . . . . . . . . . . . . . . . . . 0.25"
NPTFAir Exhaust . . . . . . . . . . . . . . . . . . 0.75"
NPTFSuction Lift 5.83' Dry/25.5' Wet (1.78m/777m)Max. Particle Size
(Diameter) . . . 0.3125" (1mm)Shipping WeightsAcetal . . . . . . .
. . . . . . . . . . . 5.00 lbs (2.27 kg)Polypropylene . . . . . . .
. . . . . . 3.38 lbs (1.53 kg)PVDF . . . . . . . . . . . . . . . .
. . . 4.13 lbs (1.87 kg)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
-
2.79[71]
0.94[24]
Opposite Side:1/4" Female NPT Air Exhaust
Removable Foot Pad5/16" Mounting Hole 3/8" Female NPT
Fluid Discharge Connection
3/8" Female NPTFluid Suction Connection
1/4" Female NPT Air Inlet Connection
5.32[135]
0.20[5]
2.07[53]
4.09[104]
POLY5.13[130]
KYNAR5.08[129]
POLY5.72[145]
KYNAR5.67[144]
2.07[53]
inches [mm]
5
E83/8" Bolted Plastic Pumps
Consult factory for certified drawings.
www.versamatic.com
Meters FeetDi
scha
rge
Head
in P
SI1 53
0
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0
75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0
642 7 8 90
5 10 15 20 25 30 35Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.0045 Gal. (0.017 L)
1
3
5
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 1 1.7 3 5.1 5 8.5
Flow Rate adjustable to . . . 0-6.8 gpm (26 lpm)Port SizeInlet
and Discharge . . . . . . . . . 3/8" NPTF (BSP)Air Inlet . . . . .
. . . . . . . . . . . . . . . . . 0.25" NPTAir Exhaust . . . . . .
. . . . . . . . . . . . . 0.25" NPTSuction Lift (dry) . . . . . . .
. . . . . . . 16' (4.9 m)PTFE (dry) . . . . . . . . . . . . . . . .
. . . . 16' (4.9 m)Max. Particle Size (Dia.) . . . . . . 0.10" (2.5
mm)Shipping WeightPolypropylene . . . . . . . . . . . . . . 3.0 lbs
(1.36 kg)Kynar . . . . . . . . . . . . . . . . . . . . 3.0 lbs
(1.36 kg)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
Specifications
Dimensions
Performance
-
E5
6
1/2" Bolted Metallic PumpsAluminum Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
Meters Feet Di
scha
rge
Head
in P
SI
2 10 6
0
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
12 8 4 14
40
0
5 10 15 20 25 30 35 45 50 55 Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.03 Gal. (0.11 L)
4 8
12
16
2
AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI
SCFM M3/HR 2 3.4 4 6.8 8 13.6 12 20.4 16 27.2
4.37[111]1.00
[25]
6.00[152]
3/8" NPTExhaust
(opposite side)
9.50[241]
.62[16]
5.25[133]8.50[216]
7.50[191]
3/8" NPTAir Inlet
3.25[83]
6.25[159]
10.12[257]
4.00[102]
Suction & Discharge1/2" NPT Female
inches [mm]
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
Flow Rate adjustable to . . . 0-14 gpm (53 lpm)Port Size Inlet
and Discharge . . . . . . . . . . . . . . 0.50" NPTAir Inlet . . .
. . . . . . . . . . . . . . . . . . 0.375" NPTAir Exhaust . . . . .
. . . . . . . . . . . . . 0.375" NPTSuction Lift . . 15' Dry/25'
Wet (6.096m/7.62m)PTFE . . . . . . . . 5' Dry/10' Wet
(1.52m/3.048m)Max. Particle Size (Dia.) . . . . . 0.0625"
(1.6mm)Shipping Weights316 Stainless Steel . . . . . . . . . 18 lbs
(8.17 kg)Hastelloy C . . . . . . . . . . . . . . . 18 lbs (8.17
kg)Aluminum . . . . . . . . . . . . . . . . 15 lbs (6.80 kg)
-
7
E51/2" Bolted Plastic PumpsAluminum Air Section
AvailableSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
Meters Feet Di
scha
rge
Head
in P
SI
2 10 6
0
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0
75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0
12 8 4 14
40
0
5 10 15 20 25 30 35 45 50 55 Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.03 Gal. (0.11 L)
4 8
12
16
2
AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI
SCFM M3/HR 2 3.4 4 6.8 8 13.6 12 20.4 16 27.2
2.03[52]
8.43[214]
10.06[256]
1/2" Female NPTFluid Discharge
1/2" Female NPTFluid Suction
9.30[236]
3/8" Female NPTAir Inlet Connection
3/8" Female NPTExhaust Port
11.17[284]
4.80[122] 4.00[102]
4.30[109]
6.75[171]
6.12[155]
8.30[211]
R.16[4]
inches [mm]
Flow Rate adjustable to . . . . 0-14 gpm (53 lpm)Port Size Inlet
and Discharge. . . . . . . . . . . . . . . . . . . . . . . . .
0.50" NPT I.D.. . . . . . . . . . . . . . . . . . . . . . . . .
0.75" NPT O.D.Air Inlet . . . . . . . . . . . . . . . . . . . . .
0.375" NPTAir Exhaust . . . . . . . . . . . . . . . . . . 0.375"
NPTSuction Lift. . . 15' Dry/25' Wet (6.096m/7.62m)PTFE . . . . . .
. . . 5' Dry/10' Wet (1.52m/3.048m)Max. Particle Size (Diameter) .
. 0.0625"(1.6mm)Shipping WeightsPolypropylene . . . . . . . . . . .
. . . 10 lbs (4.54 kg)Kynar® . . . . . . . . . . . . . . . . . . .
10 lbs (4.54 kg)Acetal . . . . . . . . . . . . . . . . . . . . 12
lbs (5.45 kg)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
-
E5
8
1/2" Food Processing PumpAluminum Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
Flow Rate adjustable to . . . 0-14 gpm (53 lpm)Port Size Inlet
and Discharge . . . . . . . . . . . . 1" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . 0.375"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . 0.375"
NPTSuction Lift . . 15' Dry/25' Wet (6.096m/7.62m)PTFE . . . . . .
. . 5' Dry/10' Wet (1.52m/3.048m)Max. Particle Size (Dia.) . . . .
. 0.0625" (1.6mm)Shipping Weights316 Stainless Steel . . . . . . .
. . . 18 lbs (8.17 kg)
Meters Feet Di
scha
rge
Head
in P
SI
2 10 6
0
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
12 8 4 14
40
0
5 10 15 20 25 30 35 45 50 55 Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.03 Gal. (0.11 L)
4 8
12
16
2
AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI
SCFM M3/HR 2 3.4 4 6.8 8 13.6 12 20.4 16 27.2
8.38[213]
9.35[237]
2.38[60]
10.38[264]
0.97[25]
4.38[111] 5.26
[134]8.25[210]
3.38[86] 4.00
[102]6.25[159]
7.67[195]
inches [mm]
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
www.versamatic.com
NOTE: For E5 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
-
9
E1Specifications
Dimensions
Performance
Consult factory for certified drawings.
NOTE: For E1 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
0 5 10 15 20
0 20 40
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
25 30 35
60 80
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 40
100 120 140
5
10
1520
30
40
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, (Avg.), 0.10 Gal. (0.38 L)
13.48[342]
1.70[43]
1.56[40]
10.87[276]
13.67[347]
1.58[40]
.50[13]
.63[16]
7.75[197]
8.06[205]
4.75[121]
3.50[89]
10.62[270]
inches [mm]
3/8" Female NPT Air Inlet Connection
1/2" Female NPT Exhaust Port (opposite side)
Flow Rate adjustable to . . . 0-35 gpm (132 lpm)Port SizeInlet
and Discharge . . . . . 1.0" Female NPT (BSP)Air Inlet . . . . . .
. . . . . . . . . . . . . . . 0.375" NPTAir Exhaust . . . . . . . .
. . . . . . . . . . . 0.50" NPTSuction Lift. . . . 15' Dry/25' Wet
(4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Diameter) . .
0.125"(3.17mm)Shipping WeightsAluminum . . . . . . . . . . . . . .
. . 31 lbs (14.07 kg)316 Stainless Steel . . . . . . . . . 42 lbs
(19.05 kg)Hastelloy C . . . . . . . . . . . . . . . 42 lbs (19.05
kg)
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
1" Bolted Metallic Pumps with Plastic Centers
www.versamatic.com
-
E1
10
1" UL Listed Pumpwith Grounding Strap
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
0 5 10 15 20
0 20 40
35
30
25
20
15
10
5
0
25 30 35
60 80
50
45
40
35
30
25
20
15
10
5
0
120 110 100
90 80 70 60 50 40 30 20 10
0 40
100 120 140
5 1015
20
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68
Meters Feet
Disc
harg
e He
ad in
PSI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, (Avg.), 0.10 Gal. (0.38 L)
1" Female NPT Fluid Inlet Connection(1" BSP also available)
1" Female NPT Fluid Discharge Connection(1" BSP also
available)
3/8" Female NPT Air Supply Connection3/8" Female NPT Air Supply
Connection
1/2" Female Air Exhaust(Oppisite Side)
8.06[205]
13.48[343]
10.41[265]
4.82[122]
3.78[96]
8.25[210]
11.77[299]
8.27[210]
1.52[38.5]
inches [mm]
Flow Rate adjustable to . . . 0-35 gpm (132 lpm)Port SizeInlet
and Discharge . . . . . 1.0" Female NPT (BSP)Air Inlet . . . . . .
. . . . . . . . . . . . . . . 0.375" NPTAir Exhaust . . . . . . . .
. . . . . . . . . . . 0.50" NPTSuction Lift. . . . 15' Dry/25' Wet
(4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Diameter) . .
0.125"(3.17mm)Shipping WeightAluminum . . . . . . . . . . . . . . .
. 31 lbs (14.07 kg)
CAUTION: Do not exceed 50 psig (3.4 bars) air supply or liquid
pressure.
NOTE: For E1 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
-
11
E11" Bolted Plastic Pumps with Plastic Centers Standard Side
Porting — Aluminum Air Section AvailableSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E1 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
4.13[105] 5.13[130]
5.50[140]
7.20[182]
R.25[6]
13.60[344]
14.80[375]
11.40[290]
2.50[64]
inches [mm]
1/2" Female NPTAir Exhaust Connection
(on opposite side)3/8" Female NPT
Air Inlet Connection 1" ANSI 150#/DIN 325 Flange(both inlet and
discharge connections)
0 5 10 15 20
0 20 40
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
25 30 35
60 80
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 40
100 120 140
5
10
1520
30
40
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, (Avg.), 0.10 Gal. (0.38 L)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
Flow Rate adjustable to . . . 0-35 gpm (132 lpm)Port SizeInlet
and Discharge . . . . . 1.0" ANSI/DIN FlangedAir Inlet . . . . . .
. . . . . . . . . . . . . . . 0.375" NPTAir Exhaust . . . . . . . .
. . . . . . . . . . . 0.50" NPTSuction Lift. . . . 15' Dry/25' Wet
(4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia) . . . . . .
0.125"(3.17mm)Shipping WeightsPolypropylene . . . . . . . . . . . .
. 24 lbs (10.89 kg)Kynar® . . . . . . . . . . . . . . . . . . 24
lbs (10.89 kg)
-
E1
12
1" Bolted Plastic Pumps with Plastic CentersOptional Center
Porting — Split Manifolds and Aluminum Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E1 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
1/2" Female NPTAir Exhaust Connection(On Opposite Side)
1" ANSI 150#/ DIN #25Fluid Discharge Connection
8.06[205]
14.32[364]
11.70[297]
10.10[257]
R25[6]
5.13[130]
7.90[201]
6.24[158]
2.23[57]
1" ANSI 150#/ DIN #25Fluid Suction Connection
inches [mm]
3/8" Female NPTAir Inlet Connection
0 5 10 15 20
0 20 40
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
25 30 35
60 80
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 40
100 120 140
5
10
1520
30
40
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, (Avg.), 0.10 Gal. (0.38 L)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
Flow Rate adjustable to . . . 0-35 gpm (132 lpm)Port SizeInlet
and Discharge . . . . . 1.0" ANSI/DIN FlangedAir Inlet . . . . . .
. . . . . . . . . . . . . . . 0.375" NPTAir Exhaust . . . . . . . .
. . . . . . . . . . . 0.50" NPTSuction Lift. . . . 15' Dry/25' Wet
(4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia.) . . . . . .
0.125"(3.17mm)Shipping WeightsPolypropylene . . . . . . . . . . . .
. 24 lbs (10.89 kg)Kynar® . . . . . . . . . . . . . . . . . . 24
lbs (10.89 kg)
-
13
E11" Food Processing PumpAluminum Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
0 5 10 15 20
0 20 40
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
25 30 35
60 80
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 40
100 120 140
5
10
1520
30
40
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, (Avg.), 0.10 Gal. (0.38 L)
2.00[51]
.50[13]
3.50[89]
.63[16]
7.75[197]
8.06[205]
14.32[364]
13.63[346]
1.56[40] 4.75
[121]
2.00[51]1.70
[43]
10.62[270]
10.87[276]
inches [mm]
Flow Rate adjustable to . . . 0-35 gpm (132 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . 1.5" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . 0.375"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.50"
NPTSuction Lift. . . . 15' Dry/25' Wet (4.57m/7.62m)PTFE . . . . .
. . . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size (Diameter)
. . 0.125"(3.17mm)Shipping Weights316 Stainless Steel . . . . . . .
. . 42 lbs (19.05 kg)
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
NOTE: For E1 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
www.versamatic.com
-
E4
14
1-1/4" Clamped Metallic Pumps1-1/2" Discharge Manifold
Available, Screen Mount Available for Aluminum Model
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E4 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
1/2" Female NPTAir Supply Connection
1-1/4" Female NPTFluid Discharge
1-1/2" Female NPTSuction Connection
3/4" Female NPTAir Exhaust Connection
6.00[152]
7.74[197]
13.81[351]
11.63[295]
13.5[343]
14.25[361]
2.37[60]
18.0[457]
13.37[340]
8.75[222]
inches [mm]
Bottom View
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 0 10 20 30 40 50 60 70
0 40 80 120 160 200 240 280
30
40
50
2010
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, .31 Gal. (1.17 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 50 85
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
Flow Rate adjustable to . . . 0-70 gpm (265 lpm)Port SizeInlet .
. . . . . . . . . . . . . . . . . . . . 1.50" NPT (BSP)Discharge .
. . . . . . . . . . . . . . . . 1.25" NPT (BSP)Air Inlet . . . . .
. . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . . .
. . . . . . . . . . . . . 0.75" NPTSuction Lift. . . . 15' Dry/25'
Wet (4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.09m)Max. Particle Size (Dia.) . . . . .
0.1875"(4.76mm)Shipping WeightsAluminum . . . . . . . . . . . . . .
. . 41 lbs (18.60 kg)Cast Iron . . . . . . . . . . . . . . . . 57
lbs (25.85 kg)Hastelloy C . . . . . . . . . . . . . . . 57 lbs
(25.85 kg)316 Stainless Steel . . . . . . . . . 57 lbs (25.85
kg)
-
15
E41-1/2" Bolted Metallic PumpsStandard Vertical Discharge —
Horizontal Discharge AvailableSpecifications
Dimensions
Performance
Consult factory for certified drawings.
NOTE: For E4 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
20.22 [514]
8.78 [223] 10.28
[261]
3.13[80]
3.12 [79]
2.81 [72]
5.94 [151]
7.00 [178]
11.34 [288]
5.92 [150]
10.50 [267]
12.82 [326]
13.20 [335]
0.44 [11] Slot Width
40mm ANSI/DIN Flange 1.50" 150# Flange Discharge
40mm ANSI/DIN Flange 1.50" 150# Flange Discharge
.50" Female NPT Air Inlet
inches [mm]
90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
120
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 0 10 20 30 40 50 60 70
0 40 80 120 160 200 240 280
260 280
40
60
20
Meters Feet Di
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.31 Gal. (1.17 L)
AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 50 85
Flow Rate adjustable to . . . 0-72 gpm (275 lpm)Port Size Inlet
and Discharge . . . . . . . . . . . 1.50" ANSI/DINAir Inlet . . . .
. . . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . .
. . . . . . . . . . . . . . 0.75" NPTSuction Lift . . . 15' Dry/25'
Wet (4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.09m)Max. Particle Size (Dia.) . . . . .
0.1875"(4.76mm)Shipping Weights316 Stainless Steel . . . . . . . .
. 65 lbs (29.48 kg)Hastelloy C . . . . . . . . . . . . . . . 68 lbs
(30.84 kg)
www.versamatic.com
-
E4
16
1-1/2" Bolted Plastic PumpsSwivel Inlet/Discharge
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E4 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
15.71[399]
11.71[298]
3.22[82]
0.44[11]
11.92[303]
4.75 [121]6.07 [154]
6.90 [175]
12.15[309]
7.00[178]
8.00[203]
9.31[237]
18.85[479]
21.60[549]
inches [mm]
1/2" Female NPTAir Supply
40mm ANSI/DIM Flange0.50", 150# Class Discharge
90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
120
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 0 10 20 30 40 50 60 70
0 40 80 120 160 200 240 280
260 280
40
60
20
Meters Feet Di
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.31 Gal. (1.17 L)
AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 50 85
Flow Rate adjustable to . . . 0-72 gpm (272 lpm)Port SizeInlet
and Discharge . . . . 1.50" ANSI/DIN FlangedAir Inlet . . . . . . .
. . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . . . . .
. . . . . . . . . . . 0.75" NPTSuction Lift . . . 15' Dry/25' Wet
(4.57m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.09m)Max. Particle Size (Dia.) . . . . .
0.1875"(4.76mm)Shipping WeightsPolypropylene . . . . . . . . . . .
. . 32 lbs (14.51 kg)Kynar® . . . . . . . . . . . . . . . . . . 45
lbs (20.41 kg)
-
17
E41-1/2" Food Processing PumpSpecifications
Dimensions
Performance
Consult factory for certified drawings.
NOTE: For E4 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
FG69C
FG69C
FG69C
FG69C
FG
39
C
FG
39
C
14.50[368]
13.50[343]
2.43[62]
2.50[64]
11.43[290]
6.00[152]
8.75[222]
10.25[260]
2.50DIA[64]
7.06[179]
17.31[440]
16.51[419]
2" Tri-Clover Fitting
2" Tri-Clover Fitting 1/2" Female NPTAir Supply Connection
3/4" Female NPTAir Exhaust Connection
inches [mm]
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
110
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 0 10 20 30 40 50 60 70
0 40 80 120 160 200 240 280
30
40
50
2010
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, .31 Gal. (1.17 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 50 85
Flow Rate adjustable to . . . 0-70 gpm (265 lpm)Port Size Inlet
and Discharge . . . . . . . . . . . . . 2" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction Lift . . . 15' Dry/25' Wet (4.57m/7.62m)PTFE . . . . . .
. . . 10' Dry/20' Wet (3.05m/6.09m)Max. Particle Size (Dia.) . . .
. . 0.1875"(4.76mm)Shipping Weights316 Stainless Steel . . . . . .
. . . 57 lbs (25.85 kg)
www.versamatic.com
-
E4
18
1-1/2" Sanitary Pump3A Certified Models Available with
Versa-Sense™ II Leak Detection System
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E4 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
1-1/2" Tri-Clamp Connection
1-1/2" Tri-ClampConnection
1/2" NPT Air InletConnection
3/4" NPT Air Exhaust Connection
29.80[757]
2.00[51]
2.00[51]
11.02[280]
15.20[386]
25.72[653]
9.80[249]
14.00[356]
15.57[396]
18.57[472]
10.00[254]
3.00[76]
.63 Dia.[16]
inches [mm]
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 50 85
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
100
90
80
70
60
50
40
30
20
10
0
240 220 200 180 160 140 120 100
80 60 40 20
0 0 10 20 30 40 50 60 70
0 40 80 120 160 200 240 280
1020
30
40
50
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.31 Gal. (0.11 L)Flow Rate adjustable
to . . . 0-60 gpm (227 lpm)Port SizeInlet and Discharge . . . . . .
. . . . . 1.5" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction LiftPTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia.) . . . . 0.375"
(9.53mm)Surface Finish . . 32 micro-inch (0.8 micrometerShipping
Weight316 Stainless Steel . . . . . . . . . 75 lbs (34.09 kg)
-
19
E22" Clamped Metallic PumpsScreen Mount Available for Aluminum
Model, Stainless Steel Air Section AvailableSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
0.50" FNPTAir Valve Connection
2.0" FNPT (BSP)Discharge
2.0" FNPT(BSP) Inlet
OPTIONAL SCREEN BASE(Aluminum Pumps Only)
FOOTED BASE
1.50[38]
1.75[44]
19.75[502]
25.00[635]
26.50[673]
6.50[165]
10.00[254]
12.00[305]
9.00[229]
10.50[267]
11.25[286]
11.00[279]
2.50[64]
inches [mm]
16.13[410]
0.50[13]Wide Slot
0.56[14]
Diameter
0 20 40 60 80 100 120
0 50 100 150 200 250 300 350 400 450 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
2030 40
60
80
100
10
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.70 Gal. (2.65 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 60 102 80 136100 170
Flow Rate adjustable to . . 0-155 gpm (586 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . 2.0" NPT (BSP)Air Inlet . . . .
. . . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . .
. . . . . . . . . . . . . . 0.75" NPTSuction Lift . . . 20' Dry/25'
Wet (6.10m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia.) . . . . . . .
0.25"(6.35mm)Shipping WeightsAluminum . . . . . . . . . . . . . . .
. 70 lbs (31.75 kg)Cast Iron . . . . . . . . . . . . . . . . 115
lbs (52.16 kg)316 Stainless Steel . . . . . . . . 115 lbs (52.16
kg)Hastelloy C . . . . . . . . . . . . . . 125 lbs (56.70 kg)
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
-
E2
20
2" Bolted Metallic PumpsStandard Vertical Discharge — Horizontal
Discharge Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
3.19[81]
27.73[704]
12.00[305] 17.71
[450]
19.98[508]
13.50[343]
11.50[292]
11.00[279]
10.00[254]
2.00[51]
3.39[51]
inches [mm]Discharge Connection:2" ANSI 150# Raised Face
Flange(DIN Compatible)
Suction Connection:2" ANSI 150# Raised Face Flange(DIN
Compatible)
Air Supply Connection:1/2" Female NPT
0 20 40 60 80 100 120
0 50 100 150 200 250 300 350 400 450 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
2030 40
60
80
100
10
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.70 Gal. (2.65 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 60 102 80 136100 170
Flow Rate adjustable to . . 0-155 gpm (586 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . . . . 2.0" ANSI,. . . . . . . .
. . . . . . . . . . . . . 150 lb class (DIN 50)Air Inlet . . . . .
. . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . . .
. . . . . . . . . . . . . 0.75" NPTSuction Lift . . . 20' Dry/25'
Wet (6.09m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.09m)Max. Particle Size (Dia.) . . . . . . .
0.25"(6.35mm)Shipping Weight316 Stainless Steel . . . . . . . . 120
lbs (54.43 kg)Hastelloy C . . . . . . . . . . . . . . 120 lbs
(54.43 kg)Cast Iron . . . . . . . . . . . . . . . . 120 lbs (54.43
kg)
-
21
E22" Bolted Aluminum PumpsSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2AL pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
24.88[632]
20.27[515]
26.38[670]
3.00[76]
17.66[449]
13.13[334]
10.50[267]
R0.25[R6]
13.45[342]
9.00[229]
10.45[266]
2.52[64]
inches [mm]
1/2" Female NPTAir Line
Connection
3/4" Female NPTAir Exhaust Connection
2" Female NPT or BSPSuction Connection
2" Female NPT or BSPDischarge Connection
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 40 68 60 102 80 136100 170120 204140 238
0
0 50 100 150 200 250 300 350 400 450 500
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0 10 30 50
600
70 90 110 130 150 170
550
2040
60
80100
120
140
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.60 Gal. (2.33 L)Flow Rate adjustable
to . . 0-174 gpm (658 lpm)Port SizeInlet . . . . . . . . . . . . .
. . . . . . . . . 2.0" NPT (BSP)Discharge . . . . . . . . . . . . .
. . . . . 2.0" NPT (BSP)Air Inlet . . . . . . . . . . . . . . . . .
. . . . . 0.50" NPTAir Exhaust . . . . . . . . . . . . . . . . . .
. 0.75" NPTSuction Lift . . . 20' Dry/25' Wet (6.10m/7.62m)PTFE . .
. . . . . . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size
(Dia.) . . . . . . . . 0.43"(11mm)Shipping WeightAluminum . . . . .
. . . . . . . . . . . 74 lbs (33.34 kg)
-
E2
22
2" High Pressure Pumps
Specifications Performance
Consult factory for certified drawings.
9.00[229]
11.78[299]
10.34[263]
11.00[279]
21.83[555]
27.39[696]
23.10[587]
4.29[109]
R .28[7]
18.29[465]
1/2"-14 NPTT AirSupply Connection10.73
[273]
11.68[297] inches [mm]
2" ANSI 300# Class(DIN Compatible)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
DISPLACEMENT PER STROKE, .70 GAL. (2.6 L)
220
200
180
160
140
120
100
80
60
40
20
0 0 10 20 30 40 50 60 70
240
0 25 50 75 100 125 150 175 200 225 250 275
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
530 490 450 410 370 330 290 250 210 160 120
80 40
0
160
140
120
100
80
60
40
20
0
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 30 51 40 68 50 85 60 102 70 119 80 136 90
153
10
60
70
80
90
20
30
40
50
60
70
80
90
100
120
110
20
30
4050
Flow Rate adjustable to . . . 0-69 gpm (261 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . . . . .2.0" ANSI, . . . . . . .
. . . . . . . . . . . . . . 300 lb class (DIN 50)Air Inlet . . . .
. . . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . .
. . . . . . . . . . . . . . . 1.0" NPTSuction Lift . . . 20'
Dry/25' Wet (6.10m/7.62m)Max. Particle Size (Dia.) . . . . . . .
0.25"(6.35mm)Shipping Weight316 Stainless Steel . . . . . . . . .
91 lbs (41.28 kg)
Dimensions
www.versamatic.com
-
23
E22" Flap Valve Pumpswith Top Inlet and Bottom
DischargeSpecifications
Dimensions
Performance
Consult factory for certified drawings.
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 40 68 60 102 80 136100 170120 204
0 20 40 60 80 100 120
0 100 200 300 400 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0 160 180
600 700
2040
60
80
100
120
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.82 Gal. (3.1 L)
1.50[38]
21.94[557]
25.25[641]
28.50[724]
6.88[175]
6.88[175]
9.00[229]
10.75[273]
12.00[305]
10.00[254]
17.50[445] inches [mm]
2" Female NPT (BSP)Inlet Connection
2" Female NPT (BSP)Discharge Connection
1/2"NPT AirValve Connection
Flow Rate adjustable to . . 0-180 gpm (681 lpm)Port SizeInlet
and Discharge. . . . . . . 2.0" Male NPT (BSP) Air Inlet . . . . .
. . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . . .
. . . . . . . . . . . . . 0.75" NPTSuction Lift . . . 10' Dry/10'
Wet (3.05m/3.05m)Max. Particle Size (Dia.) . . . . .
1.125"(28.57mm)Shipping WeightAluminum . . . . . . . . . . . . . .
. . 88 lbs (39.92 kg)
NOTE: For E2FV pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
www.versamatic.com
-
E2
24
2" Bolted Plastic PumpsStandard Side Porting
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2P pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
0 20 40 60 80 100 120
0 50 100 150 200 250 300 350 400 450 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
2030 40
60
80
100
10
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.70 Gal. (2.65 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 60 102 80 136100 170
E
ANSI Pipe Flange150 Pound Class
(DIN 50)
ANSI Pipe Flange150 Pound Class
(DIN 50)
.50" NPT Air Valve Connection
19.81[778]
12.75[324]
3.06[78]
3.06[78]
10.12[257]
9.00[229]
24.25[615]
24.25[615]
27.31[694]
30.31[770]
12.00[305]
inches [mm]
Flow Rate adjustable to . . 0-155 gpm (586 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . . . . 2.0" ANSI,. . . . . . . .
. . . . . . . . . . . . . . 150 Class (DIN 50)
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction Lift . . . 20' Dry/25' Wet (6.10m/7.62m)PTFE . . . . . .
. . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size (Dia.) . . .
. . . . 0.25"(6.35mm)Shipping WeightsPlastic w/Aluminum Center . .
. 72 lbs (32.68 kg)Plastic w/Stainless Center . . . 106 lbs (48.12
kg)Kynar® w/Aluminum Center . . . 98 lbs (44.49 kg)Kynar®
w/Stainless Center . . . 132 lbs (59.92 kg)
-
25
E22" Bolted Plastic PumpsOptional Center Porting with Adjustable
Inlet/DischargeSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2P pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
0 20 40 60 80 100 120
0 50 100 150 200 250 300 350 400 450 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
2030 40
60
80
100
10
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.70 Gal. (2.65 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 60 102 80 136100 170
1/2"NPT AirValve Connection
12.00[305]
24.25[616]
21.56[548]
12.75[324]
1.00[25]
12.01[305]
17.69[449]
27.25[692]
30.25[768]
9.00[229]
10.12[257]
3.06[78]
4.14[105]
inches [mm]
ANSI Class 150 Pipe Flange(DIN 50)
3/4" NPTExhaust Connection
ANSI Class 150 Pipe Flange(DIN 50)
Flow Rate adjustable to . . 0-155 gpm (586 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . . . . 2.0" ANSI,. . . . . . . .
. . . . . . . . . . . . . . 150 Class (DIN 50)
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction Lift. . . . 20' Dry/25' Wet (6.10m/7.62m)PTFE . . . . .
. . . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size (Dia.) . .
. . . . . 0.25"(6.35mm)Shipping WeightsPlastic w/Aluminum Center .
. . 76 lbs (34.56 kg)Plastic w/Stainless Center . . . 110 lbs
(49.99 kg)Kynar® w/Aluminum Center . . 102 lbs (46.36 kg)Kynar®
w/Stainless Center . . . 136 lbs (61.78 kg)
-
E2
26
2" Food Processing PumpStainless Steel Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E2 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
19.75[502]
3.00[76]
1.75[44]
16.12[409]
24.75[628]
26.50[673]
14.12[359]
12.00[305]
10.00[254]
9.00[228]
10.00[254]
3.00[76]
1/2" NPT FemaleAir Supply Connection
2-1/2" Tri-ClampInlet Port
2-1/2" Tri-ClampDischarge Port
FG39C
FG
30
D
FG39C
FG39C
FG39C
FG
30
D
inches [mm]
0 20 40 60 80 100 120
0 50 100 150 200 250 300 350 400 450 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
2030 40
60
80
100
10
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.70 Gal. (2.65 L)
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 10 17 20 34 30 51 40 68 60 102 80 136100 170
Flow Rate adjustable to . . 0-155 gpm (586 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . 2.5" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction Lift . . . 20' Dry/25' Wet (6.10m/7.62m)PTFE . . . . . .
. . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size (Dia.) . . .
. . . . 0.25"(6.35mm)Shipping Weights316 Stainless Steel . . . . .
. . . 115 lbs (52.16 kg)
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
-
27
E22" Sanitary Pump3A Certified Models Available with
Versa-Sense™ II Leak Detection SystemSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 40 68 60 102 80 136100 170120 204
0 20 40 60 80 100 120
0 100 200 300 400 500
140
100
90
80
70
60
50
40
30
20
10
0
75 70
65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0 160 180
600 700
2040
60
80
100
120
Meters FeetDi
scha
rge
Head
in P
SI
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.82 Gal. (3.1 L)
32.61[828]
7.10[180]
10.29[261]
14.00[356]
15.57[396]
18.57[472]
10.00[254]
3.00[76]
.63 Dia.[16]
3.50[89]
26.40[671]
6.99[177]
1/2" NPT Air Inlet Connection
3/4" NPT Air Exhaust Connection 2" Tri-Clamp Connection
2" Tri-Clamp Connection
inches [mm]
NOTE: For E2 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
Flow Rate adjustable to . . 0-180 gpm (680 lpm)PORT SIZEInlet
and Discharge . . . . . . . . . . . 2.0" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . 0.75"
NPTSuction lift PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. particle size (Dia.) . . . . 0.625"
(15.88mm)Surface Finish . . 32 micro-inch (0.8 micrometerShipping
Weight316 Stainless Steel . . . . . . . . 125 lbs (56.70 kg)
-
E3
28
3" Clamped Metallic PumpsScreen Mount Available for Aluminum
Model, Stainless Steel Air Section Available
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E3 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 60 102100 170140 238
20
60
100
140
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per MinuteMeters Feet
Disc
harg
e He
ad in
PSI
00
20
40
60
80
100
20 40 60 80 100 120 140 160 180 200 220 240
1000 200 300 400 500 600 700 800 900
Displacement Per Stroke, 1.38 Gal. (5.22 L)
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
0.50" NPT Air Valve Connection
3.0" FNPT (BSP) Inlet
3.0" FNPT (BSP) Discharge
20.00[508]
2.30[58]
2.30[58]
14.25[362]
10.00[254]
11.00[279]
0.60[15]Wide Slot
12.00[305]
9.00[229]
2.75[70]
21.50[546]
30.50*[775]
32.75*[832]
inches [mm]
* Measurement is for Cast Iron pumps. Other materials of
construction may be slightly smaller.
Flow Rate adjustable to . . 0-260 gpm (984 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . 3.0" NPT (BSP)Air Inlet . . . .
. . . . . . . . . . . . . . . . . . . 0.5" NPTAir Exhaust . . . . .
. . . . . . . . . . . . . . . 1.0" NPTSuction Lift . . . 20'
Dry/25' Wet (6.10m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Diam.) . . . .
0.375"(9.52mm)Shipping WeightsAluminum . . . . . . . . . . . . . .
. 115 lbs (52.16 kg)Cast Iron . . . . . . . . . . . . . . . . 210
lbs (95.25 kg)316 Stainless Steel . . . . . . . . 210 lbs (95.25
kg)Hastelloy C . . . . . . . . . . . . . . 220 lbs (99.79 kg)
-
29
E33" Bolted Metallic PumpsSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E3 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 60 102100 170140 238
20
60
100
140
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per MinuteMeters Feet
Disc
harg
e He
ad in
PSI
00
20
40
60
80
100
20 40 60 80 100 120 140 160 180 200 220 240
1000 200 300 400 500 600 700 800 900
Displacement Per Stroke, 1.38 Gal. (5.22 L)
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
Discharge Flange conforms to both ANSI 150# and DIN #80
Standards
Inlet Flange conforms to both ANSI 150# and DIN #80
Standards
32.38[823]
36.31[922]
25.22[641]
4.37[111]
6.94[176]
R.30[8]
6.94[176]
14.00[356]
10.00[254]
11.00[279]
16.00[406]
inches [mm]
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
Flow Rate adjustable to . . 0-230 gpm (870 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . . . . 3.0" ANSI,. . . . . . . .
. . . . . . . . . . . . . 150 lb class (DIN 80)Air Inlet . . . . .
. . . . . . . . . . . . . . . . . 0.50" NPTAir Exhaust . . . . . .
. . . . . . . . . . . . . . 1.0" NPTSuction Lift . . . 20' Dry/25'
Wet (6.10m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia.) . . . . . . .
0.75"(19.1mm)Shipping WeightsAluminum . . . . . . . . . . . . . . .
150 lbs (68.04 kg)316 Stainless Steel . . . . . . . 250 lbs (113.40
kg)Hastelloy C . . . . . . . . . . . . . 275 lbs (124.74 kg)
-
E3
30
3" Bolted Plastic Pumps
Specifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E3P pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 40 68 60 102 80 136100 170120 204140 238
20 40 6080
100
120
140
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per MinuteMeters Feet
Disc
harg
e He
ad in
PSI
00
20
40
60
80
100
20 40 60 80 100 120 140 160 180 200 220
50 150 250 350 450 550 650 750 850
Displacement Per Stroke, 0.90 Gal. (3.41 L)
75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
Suction Port: 3" [61 mm] Standard 125# Flange Configuration
Discharge Port: 3" [61mm] Standard125# Flange Configuration
Manifold can rotate 90° from vertical centerline
33.38[848]
16.69[423]
6.16[156]
17.31[440]
12.31[313]
0.19[5]
18.25[464]
35.63[905]
5.00[127]
40.63[1032]
5.00[127]
4.88[124]
20.25[124]
14.50[368]
1.09[28]
1.84[47] 6.16
[156]
8.44[214]
16.88[429]
0.75[19]Dia.16.00
[406]
inches [mm]
Flow Rate adjustable to . . 0-238 gpm (901 lpm)Port SizeInlet
and Discharge . . 3.0" ANSI or DIN 80 FlangeAir Inlet . . . . . . .
. . . . . . . . . . . . . . 0.75" NPTFAir Exhaust . . . . . . . . .
. . . . . . . . . 1.00" NPTFSuction Lift . . . 20' Dry/25' Wet
(6.10m/7.62m)PTFE . . . . . . . . . 10' Dry/20' Wet
(3.05m/6.10m)Max. Particle Size (Dia.) . . . . . . . . 0.71"
(18mm)Shipping WeightsPolypropylene . . . . . . . . . . . 231 lbs
(104.78 kg)PVDF. . . . . . . . . . . . . . . . . . 315 lbs (142.88
kg)
CAUTION: Do not exceed 100 psig (6.9 bars) air supply or liquid
pressure.
-
31
E33" Food Processing PumpStainless Steel Air Section
AvailableSpecifications
Dimensions
Performance
Consult factory for certified drawings.
www.versamatic.com
NOTE: For E3 pumps fitted with PTFE diaphragms, reduce water
discharge figures by 20%.Suction lift is reduced to 10' (3.05m) dry
and 20' (6.10m) wet.
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI
SCFM M3/HR 20 34 60 102100 170140 238
20
60
100
140
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per MinuteMeters Feet
Disc
harg
e He
ad in
PSI
00
20
40
60
80
100
20 40 60 80 100 120 140 160 180 200 220 240
1000 200 300 400 500 600 700 800 900
Displacement Per Stroke, 1.38 Gal. (5.22 L)
75 70 65 60 55 50 45 40 35 30 25 20 15 10
5 0
240 220 200 180 160 140 120 100
80 60 40 20
0
CAUTION: Do not exceed 125 psig (8.5 bars) air supply or liquid
pressure.
1" 11 1/2 FemaleNPT Muffler Connection
12.00[305]
14.25[362]
10.00[254]
.60 Wide Slot, Typ.[15]
11.00[279]
20.00[508]
21.50[546]
29.75[756]
32.00[813]
18.00[457] 3.47
[88]
2.30[58]
3.47[88]
3" Nominal Tri-Clover Sanitary Fitting
3" Nominal Tri-Clover Sanitary Fitting
1/2" NPT Air Supply Connection
inches [mm]
Flow Rate adjustable to . . 0-260 gpm (984 lpm)Port SizeInlet
and Discharge . . . . . . . . . . . 3.0" Tri-Clamp®
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . 0.5"
NPTAir Exhaust . . . . . . . . . . . . . . . . . . . . 1.0"
NPTSuction Lift . . . 20' Dry/25' Wet (6.10m/7.62m)PTFE . . . . . .
. . . 10' Dry/20' Wet (3.05m/6.10m)Max. Particle Size (Diam.) . . .
. 0.375"(9.52mm)Shipping Weights316 Stainless Steel . . . . . . . .
210 lbs (95.25 kg)
-
32
Submersible Pumps
www.versamatic.com
Sub
Specifications
Model Number . . . . . . . . . . . . . . . . . . . SPA15Maximum
Flow . . . . . . . . . . 43 gpm (163 lpm)Maximum Head Pressure . .
. . . . . . 25' (7.6 m)Fluid Outlet . . . . . . . 1.5" NPT or BSPT
(female) Weight . . . . . . . . . . . . . . . . . . 33 lbs (14.37
kg)
Model Number . . . . . . . . . . . . . . . . . . . AP50/2Maximum
Flow . . . . . . . . . 125 gpm (473 lpm)Maximum Discharge Pressure
48 psi (3.3 bar)Max. Solid Particle Size . . . . . . . 0.25" (6
mm)Air Inlet . . . . . . . . . . . 0.75" NPT or BSP (male) Exhaust
Outlet. . . . . . 1.0" NPT or BSP (female) Fluid Discharge. . . . .
2.0" NPT or BSP (female)Weight . . . . . . . . . . . . . . . . . .
71 lbs (32.21 kg)
Specifications
Air-Driven High-Flow Pump • Fully submersible• Weighs 59 lbs •
Won’t choke on small trash• Can run dry without damage• Handles
solids up to 1.5"• Self-draining to prevent damage
in subfreezing weather• Fits in openings as small as 14"
diameter• Self-priming and continuous
automatic lubricating• Optional rock screen for 1/2"
solids available• Fool-proof design that
handles abrasive substanceswith less wear
• Built for rough handling andlong life on land, sea or
offshore
Model Number . . . . . . . . . . . . . . . . . . SMA3-AMaximum
Flow . . . . . . . . 300 gpm (1,140 lpm)Maximum Discharge Pressure
. 28 psi (2 bar)Max. Solid Particle Size . . . . . 1.5" (38.1
mm)Air Inlet . . . . . . . . . . . . . . . . . . . . . . 0.50" NPT
Exhaust Outlet. . . . . . . . . . . . . . . . . 0.75" NPT Fluid
Discharge . . . . . . . . . . 3.0" NPT (female)Weight . . . . . . .
. . . . . . . . . . . 59 lbs (26.76 kg)
Specifications
Battery-Powered Portable Pump • Runs off any 12-volt
truck/auto
battery• Fully submersible• Fits in openings as small as
10" diameter• Weighs just 33 lbs.• 30 foot cord • Whisper-quiet•
Needs no suction hose, engine
cranking or gas cans • Remote waterproof controller
for simple, safe operation• Low 30-amp draw for an hour
(average) of operation withoutrestarting engine
• Available with both 1-1/2" NPTor BSPT (tapered thread)female
connections
• Self-lubricating shaft seal, bearing lubricated for life
Porta-Matic™ SludgeMaster™AP50
Air-Driven High-Pressure Pump• Fully submersible• Available in
2"• Compact and weighs 71 lbs.• Fits in openings as small as
16" diameter• Low noise levels• Long service life• Easy
maintenance• Convenient carrying handle• Can run dry without
damage• Sealed construction• Safe in hazardous areas• Integral
baseplate/strainer• Open impeller for slurry
and solids
-
Versa-Matic® now offers a complete range of Elima-Matic® pumps
that have been independentlycertified as compliant to the European
ATEX 100Adirective for explosive atmospheres. These pumpsare
available in sizes from 1/2" to 3", in a variety of materials of
construction — including easily distinguishable black polypropylene
— and with a wide selection of diaphragm choices to ensure the best
compatibility for products pumped involatile environments.
33
SPSpecialty PumpsUL Listed Pumps
www.versamatic.com
Certified ATEX Compliant Pumps
Solids Handling Pumps
Food Processing Pumps
Versa-Matic® screen mounted and flap valve pumpsare designed to
pump mediums which contain large solids. Used extensively in the
construction andmining industries these pumps can handle
semi-solidsup to 1.125" (28.57mm) in diameter. The screenmounted
bases screen the fluid to prevent largersolids from inhibiting the
operation of the pump. They can be fully submerged for use in pits,
sumps or other bodies of fluid (see instructions for submerged
installation on page 3). These pumps can deliver flows up to 260
gpm (983 lpm) makingquick work of many difficult applications.
The UL Listed pumps havebeen tested and listed byUnderwriters
Laboratories for safe, spark-free flammableliquid transfer
applicationssuch as diesel fuel, kerosene,gasoline, aviation fuel,
alcohol,and many others. They areavailable in a variety of
different wet end materials of construction.
Elima-Matic® food-processing pumps are built withFDA-compliant
materials so they can be specified in applications requiring FDA
approval. The innovative
Elima-Matic® air valvesystem virtually eliminatesicing, stalling
and theneed for lubrication.Elima-Matic FDA pumpsare available in
1/2", 1", 1-1/2", 2" and 3"sizes with optional Versa-Sense™
leakdetection system.
• Electro-polished, 316 stainless steel wetted sections
• Hytrel® and PTFE food-grade elastomers
• Tri-clamp connections and wing-nut clamp bandsfor quick
disassembly/assembly
• Nickel-plated aluminum center sections
• Flow range up to 260 gal/min
• Pre-cast bosses for use with optional leak detectors
-
Dia
34
Diaphragms
www.versamatic.com
Versa-Matic’s high quality fabricreinforced standard
rubberdiaphragms. Designed to reducemaintenance and repair
costs.Interchangeable with mostWilden® pump models.
The simple, smooth dome shape eliminates complex angles
—delivering the flex across theentire face of these diaphragms. The
distribution of flex allowsthem to last up to 300% longer than
standard diaphragms. Interchangeable with Wilden®
pumps.
FDA Hytrel® food gradediaphragms are approved for usewith food
and dairy mediums.FDA Hytrel® diaphragms are also excellent in
abrasive producttransfer applications.
Versa-Matic is the innovator ofThermoplastic XL diaphragms. They
have much of the chemicalresistance of PTFE diaphragms,but cost
significantly less and areextremely abrasion resistant.
Interchangeable with Wilden®
pumps.
Versa-Tuff® PTFE diaphragms are single-piece diaphragms
combining the chemical resistanceof PTFE with the flex-life of
rubber. They offer three times the burst strength of standardPTFE
overlays. Interchangeablewith most Wilden® 1-1/4", 2" and3"
metallic pumps.
By using an exclusive bondingprocess and unique concavedesign,
FUSION™ Integrated-PlateBonded PTFE diaphragmsenhance flow rates,
displacementper cycle and suction lift. Backingribs allow for
extended life anddeflection ridges eliminate radialcracking and
potential leak paths.Easy to install — simply spin onand hand
tighten.
FUSION™ PTFE Bonded
Versa-Rugged VR™ Series Versa-Dome®
TPE-XL Thermoplastic Versa-Tuff® PTFE
FDA Hytrel® Thermoplastic
Industry First
Industry First Integrated-Plate
-
FRLs improve pump performanceand reduce maintenance costs.Used
to filter particles and waterout of the compressed air cominginto
the pump, as well as controlthe air pressure. Also
controlslubrication amounts to optimizepump performance.
These units, operated entirely by mechanical and pneumaticmeans,
port air through a specialregulator to start or stop AODD pumps.
Manufactured with corrosion-resistant wettedcomponents and
featuring explosion-proof construction, they require no electrical
connections and are adjustablefrom a few inches to
approximatelynine feet. Ideal for sump and fluid transfer
applications.
By sensing liquid on the air sideof a diaphragm pump,
theVERSA-SENSE™ II ElectronicLeak Detector has the ability todetect
diaphragm failure. Displaylights on the control unit indicatewhich
diaphragm has failed, andwhich air chamber has been contaminated.
The control unitcan be easily wired to an audiblealarm or pump
shutdown device.
35
AccAccessories
www.versamatic.com
Anti-Shock Valves Surge Suppressors Pail & Drum Transfer
Kits
Filter/Regulator/Lubricators Level Controllers Leak Detector
Protect your pumps, pipes anddiaphragms from damage
duringstart-ups. Our Smart Start Anti-shock valves enable
com-pressed air to gradually increaseto the desired pressure over
atime period of up to 30 seconds.
Our surge suppressors providevirtually pulse-free discharge
flow,for steadier pressure and lesssystem vibration and noise.
Self-charging and self-venting.
These adapter kits easily connect1/4" or 1/2" plastic pumps to a
5-gallon bucket, 120 lb. barrel or55-gallon drum for a
cleanerapplication.
-
TG
36
Troubleshooting Guide
1 Build up of solids in water chamber2 Elima-Matic pump missing
bumper washers (see Operating Manual)3 Loose diaphragm plates
1 Cavitation2 Excessive flooded suction pressure3 Misapplication
(chemical/physical incompatibility)4 Wrong type of lubrication
(attack on air side)5 Incorrect diaphragm plates6 Diaphragm plates
on backwards7 Incorrect shaft with corresponding elastomer8 Start
up at full air pressure9 Excessive dry running at high air
pressure
1 Diaphragm failure — product leaking out exhaust2 Diaphragm
plates loose — product leaking out exhaust3 Clamp bands loose —
product leaking out clamp bands4 Clamp bands stretched — product
leaking out clamp bands5 PTFE gasket tape ruined6 Excessive
positive suction pressure — product leaking around many
or all clamp bands7 Diaphragms stretched around center hole or
bolt holes8 Clamp bands not seated properly9 Excessive air supply
pressure
1 Over lubrication/under lubrication2 Wrong type of lubrication3
Icing4 Clogged manifolds5 Deadhead (system pressure meets or
exceeds air supply pressure)6 Cavitation on suction side7 Lack of
air (line size, PSI, CFM)8 Worn o-rings9 Vapor pressure
10 Incorrect pump size
1 Cavitation on suction side2 Valve ball(s) not seating properly
or sticking3 Valve ball(s) missing (pushed into pump/thermal
expansion or missing)4 Valve ball(s)/seat(s) damaged or attacked by
product
(swelling, shrinking, etc.)5 Vapor pressure6 Clogged suction
line
1 Over lubrication2 Lack of air (line size, PSI, CFM)3 Centering
of spool (“V" series)4 Worn o-rings5 Air porting in center block is
plugged6 Wrong type of lubrication (attack on o-rings) — see
Operating Manual7 Debris in air valve8 Clogged manifolds9 Incorrect
o-ring placement
10 Deadhead (system pressure meets or exceeds air supply
pressure)11 Closed discharge valve
1 Incorrect o-ring placement2 Inner diaphragm plate installed
backwards3 Deadhead (system pressure meets or exceeds air supply
pressure)4 Air valve or center block gaskets installed
incorrectly
S Y M P T O M S
Product leaking through exhaustor around clamp bands
Premature diaphragm failure
Breaking and bending shafts
Pump running sluggish/stalling
Pump cycles and will not primeor low flow
Pump will not operate (stall or deadhead)
Pump cycles once and stops
PO
TE
NT
IA
LC
AU
SE
S
-
37
E3The Exclusive Elima-Matic® Air Valve SystemR
EC
OM
ME
ND
AT
IO
NS
1 Flush pump• start pump slow
2 Add bumper washers3 Double check tightness of diaphragm plates
when installing
replacement diaphragms
1 Enlarge pipe diameter on suction side of pump1,2 Move pump
closer to product
• raise pump/place pump on top of tank to reduce inlet
pressure
2 Add accumulation tank or pulsation dampener as close to the
pump as possible• start pump slowly (add smart start)
3,4 Consult Chemical Resistance Chart for compatibility with
products, cleaners, temperature limitations and lubrication
5 Check model number on pump in comparison to Operating Manual
for correct part
6 Check Operating Manual for correct installation7 Check model
number on pump in comparison to
Operating Manual for correct part (ie: PTFE shaft for PTFE
diaphragm)
8 Start up pump slowly (manually or with Smart Start)9 Install
control or automatic shutoff
1 Set lubricator on lowest possible setting.• Elima-Matic is
lube free for intermittent service
1,2 Clean center section of pump2 See Operating Manual for
recommended lubrication3 Replace standard “V" series with
Elima-Matic4 Clean manifolds to allow proper air flow5 Check system
to locate deadhead (equilibrium)
• increase air supply pressure6 Check suction condition (move
pump closer to product)7 Check:
• air line size and length• compressor capacity (HP vs cfm
required)• other usage of air in plant• air requirement by pump
(pump capacity, product viscosity and specific gravity)8 Replace
o-rings
9,10 Consult factory for evaluation and recommendation
1 Check suction condition (move pump closer to product)2 Clean
out around valve ball cage and valve seat area
• replace valve ball and valve seat if worn or damaged• check
Chemical Resistance Chart for compatibility
and proper elastomer match• use heavier valve ball material
3 Worn valve ball or valve seat (replace)• thermal expansion in
discharge pipe
(add one way valve into piping)• worn fingers in valve ball cage
(replace part)
4 Check Chemical Resistance Chart for compatibility and proper
elastomer match
5 Consult factory for evaluation and recommendation.6 Clean
suction manifold or piping
• install screen or bag filter
1 Set lubricator on lowest possible setting.• Elima-Matic is
lube free for intermittent service • clean out center section
2 Check:• air line size and length• compressor capacity (HP vs.
cfm required)• other usage of air in plant• air requirement by
pump
(pump capacity, product viscosity and specific gravity)3
Disconnect and reconnect air
• replace with Elima-Matic air valve4 Replace o-rings5 Clean
porting in center block to allow proper air flow6 Check
compatibility of o-rings with lubrication
(see Operating Manual)7 Clean air valve/filter
• check for scoring on spool and sleeve8 Clean suction or
discharge manifolds/piping
• clean filter bags or screens9 Reinstall o-rings in correct
position
(see Operating Manual for assistance)10 Increase air supply
pressure11 Open discharge valve
1 Reinstall o-rings in correct position (see Operating Manual
for assistance)
2 Reinstall inner diaphragm plate correctly3 Check system for
pressure ratio to pump4 Install gaskets with holes properly aligned
with parts
or valve and center block
1 Replace diaphragms (and back up diaphragm when using PTFE)
1,2 Clean out entire center section of pump2 Check diaphragms
for damage and retighten
diaphragm plates3 Tighten clamp bands (check for stretching)4
Replace clamp bands (apply grease to inside of
clamp band to assist complete compression)5 Replace PTFE gasket
tape with PTFE diaphragms6 Check excessive positive suction
pressure
(see Operating Manual for recommendations)• move pump closer to
product• add accumulation tank or pulsation dampener as close
to the pump as possible on suction side of pump• raise
pump/place pump on top of tank to reduce
inlet pressure• install flex hose on inlet and discharge as
recommended installation7 Check for excessive inlet pressure or
air pressure
• tighten bolts to recommended torque (see Operating Manual for
recommendation)
8 Seat clamp bands with mallet 9 Check Operating Manual for
recommendations
-
Msc
38
Materials of Construction, Temperature Limits &
Compatibility
www.versamatic.com
Alum
inum
ThermoplasticsPo
lypr
opyl
ene
Buna
-N
Neop
rene
EPDM
316
Stai
nles
s St
eel
PVDF
Vers
a-Tu
ff™
Tef-
Mat
ic™
FDA
Hytr
el®
(FKM
) Flu
oroc
arbo
n
Enca
psul
ated
Si
licon
e
NEOPRENE 0°F (-18°C) to +200°F (93°C)BUNA-N +10°F (-12°C) to
+180°F (82°C)NORDEL -60°F (-51°C) to +280°F (138°C)(KFM)
FLUOROCARBON -40°F (-40°C) to +350°F (176°C)PTFE +40°F (+4°C) to
+220°F (105°C)POLYURETHANE +10°F (-12°C) to +170°F (77°C)SANTOPRENE
(TPE XL) -20°F (-29°C) to +300°F (149°C)PFA -20°F (-29°C) to +300°F
(149°C)FDA HYTREL -20°F (-29°C) to +220°F (104°C)METALLIC PUMPS can
operate past 212°F (100°C). However, if you areoperating above
these limits, consult the factory for assistance.
PLASTIC PUMPS can operate to the following temperature limits:•
ACETAL 32°F (0°C) to 220°F (104°C• POLYPROPYLENE 32°F (0°C) to
175°F (79°C)• PVDF 10°F (-12°C) to 225°F (107°C)
NOTE: These are average temperatures. Chemicals and solvents can
havean effect on temperature limits.
Temperature Limits
Diaphragms, Valve Balls, Valve Seats & Valve Seat
O-rings
Sant
opre
ne
(TPE
XL)
● Bolted Construction ■ Clamped Construction ▲ Split Manifold
Model Available ▼ High Pressure Model Available
ELASTOMERS
DIAPHRAGMS ● ● ● ● ● ● ● ●
VALVE BALLS ● ● ● ● ● ● ● ● ●
VALVE SEATS ● ● ● ● ● ● ● ● ● ● ● ●
VALVE SEAT O-RINGS ● ● ● ● ● ●
TEFLON®
FUSI
ON™
Poly
uret
hane
MODEL Acetal® Aluminum Cast Iron Hastelloy C Polypropylene PVDF
Kynar® Stainless Steel
E6 (1/4") ■ ■ ■
E8 (3/8") ● ●
E5 (1/2") ● ● ● ●▲ ●▲ ●
E7 (3/4") ●
E1 (1") ● ● ●▲ ●▲ ●
E4 (1-1/4" – 1-1/2") ■ ■ ●■ ● ● ●■
E2 (2") ●■ ●■ ●■ ● ● ●■▲▼
E2-FV (2") ■
E3 (3") ●■ ■ ●■ ● ● ●■
Materials of Construction — Pumps
Fluid Solutions Numeric pH Level Wetted Section Construction
Metals
14ALKALINE 13
STAINLESS STEEL12
CAUSTIC 1110
CAST IRONBASIC 9
8NEUTRAL 7 ALUMINUM
65
CAST IRON4
ACID 32
STAINLESS STEEL10
Wetted Material Compatibility
-
39
I.D.Versa-Matic Pump Model Identification Codes
www.versamatic.com
X X X X X X X X X X - X X X
Model
Pump Size
Wetted Parts
Non-Wetted Parts
Diaphragm Material
Diaphragm Series
Valve Ball Material
Valve Seat Material/Valve Seat O-ring Material
Construction Design
Revision Level
Options (if applicable)
Model Pump Size Wetted Parts Non-Wetted Parts Diaphragm
MaterialE Elima-Matic 6 1/4" A Aluminum A Aluminum 1 NeopreneU
Ultra-Matic 8 3/8" C Cast Iron S Stainless Steel 2 Buna-NV V-Series
5 1/2" S Stainless Steel P Polypropylene 3 (FKM) Fluorocarbon
7 3/4" H Hastelloy C G Groundable Acetal 4 Nordel1 1" P
Polypropylene Z PTFE-coated Aluminum 5 PTFE4 1-1/4" or 1-1/2" K
Kynar J Nickel-plated Aluminum 6 XL2 2" G Groundable Acetal C Cast
Iron 7 Hytrel3 3" B Aluminum Q Epoxy-Coated Aluminum 9 Geolast
Diaphragm Series Valve Ball Material Valve Seat/Valve Seat
O-ring Material Construction DesignR Rugged 1 Neoprene 1 Neoprene 9
BoltedD Dome 2 Buna-N 2 Buna-N 0 ClampedX Thermo-Matic 3 (FKM)
Fluorocarbon 3 (FKM) FluorocarbonT Tef-Matic (2-piece) 4 Nordel 4
NordelB Versa-Tuff (1-piece) 5 PTFE 5 PTFEF FUSION (one-piece 6 XL
6 XL
integrated plate) 7 Hytrel 7 Hytrel8 Polyurethane 8
Polyurethane9 Geolast 9 GeolastA Acetal A Aluminum w/ PTFE O-ringsS
Stainless Steel S Stainless Steel w/ PTFE O-rings
C Carbon Steel w/ PTFE O-ringsH Hastelloy C w/ PTFE O-ringsT
PTFE Encapsulated Silicone O-rings
-
©2008 IDEX Corporation VMES0508
VERSA-MATIC® PUMP COMPANYA Unit of IDEX Corporation6017
Enterprise DriveExport, PA 15632-8969
(724) 327-7867Fax: (724) 327-4300www.versamatic.com
Hytrel® and Nordel® are registered trademarks of DuPont. Kynar®
is a registered trademark of Penwalt Corp. 3M™ is a trademark of
the 3M Corporation. Tri-Clamp® is a registered trademark of
Tri-Clover, Inc. Wilden® is a registered trade name of Wilden Pump
and Engineering Company, a Dover Resources Company.
Elima-Matic®, Tef-Matic™, Thermo-Matic™, Versa-Dome®,
Versa-Matic®, Versa-Sense™, Versa-Tuff® and Versa-Rugged VR™ are
registered tradenames and trademarks of IDEX Corporation.Some
Versa-Matic Tool, Inc. products are subject to patent pending
applications and issued patents. Elima-Matic U.S. Patent No.
5,326,234.
PP Pumper PartsYour Single Source for Parts Priced Right.A
division of Versa-Matic Pump Company, PumperParts is your single
source for Air-Operated DoubleDiaphragm (AODD) pump parts. The
company was formed to meetthe demands for fasterdelivery of
replacementparts at competitiveprices. PumperParts is a
globalsupplier of qualityreplacement partsthat fit Wilden®, ARO®,
and Yamada®
air-operated double diaphragm pumps.
Pumper Parts serves customers allover the world in a variety of
markets, includingchemical, paints & coatings, food processing,
pharmaceutical, construction, mining, utilities, pulp & paper,
metal finishing, and general industrial. A worldwide network of
fully-stocked distributorsand an extensive staff of qualified
professionals arecommitted to supporting these customers.
PumperParts is housed in a state-of-the-art facility to ensurethat
proper stock levels are maintained.
The Pumper Parts PromiseAll Pumper Parts products are:•
Engineered to perform as well as or better than
OEM parts — guaranteed• Manufactured to meet or exceed the
highest quality standards in theindustry• Honored with the same
repair
parts warranty as the OEM• Priced competitively —
providing savings and value
Pumper Parts ToolsThe Pumper Parts website helps you find
the parts you need fast and efficiently by allowingsearches by
product number or description. Additionally, a Chemical
Compatibility database isprovided so that you can quickly find what
materialsare most compatible with a variety of liquids.
PUMPER PARTS LLCA Unit of IDEX Corporation6017 Enterprise
DriveExport, PA 15632-8969
Tel: 724-387-1776Fax:
[email protected]
Pumper Parts and its products are not affiliated with any of the
original equipment manufacturersreferenced herein. All original
equipment manufacturers’ names, colors, pictures, descriptionsand
part numbers are used for identification purposes only.
Pumper Parts® is a registered trade name of IDEX Corporation.
All other trademarks, registeredtrademarks and product names are
the property of their respective owners.