1 Engine Turbo/Super Charging Super and Turbo-charging Why super/ turbo-charging? • Fuel burned per cycle in an IC engine is air limited – (F/A) stoich = 1/14.6 D 0 , a V f R HV f f V A F m N 2 Torq Power n 2 Q m Torq f ,v – fuel conversion and volumetric efficiencies m f – fuel mass per cycle Q HV – fuel heating value n R – 1 for 2-stroke, 2 for 4-stroke engine N – revolution per second V D – engine displacement a,0 – air density Super/turbo-charging: increase air density
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Engine Turbo/Super Charging
Super and Turbo-charging
Why super/ turbo-charging?
• Fuel burned per cycle in an IC engine is air limited– (F/A)stoich = 1/14.6
D0,aVf
R
HVff
VAFm
N2 TorqPower
n2
QmTorq
f,v– fuel conversion and volumetric efficiencies
mf – fuel mass per cycleQHV– fuel heating valuenR – 1 for 2-stroke, 2 for 4-stroke engineN – revolution per secondVD – engine displacementa,0 – air density
Super/turbo-charging: increase air density
2
Super- and Turbo- Charging
Purpose: To increase the charge density• Supercharge: compressor powered by engine output
– No turbo-lag– Does not impact exhaust treatment– Less efficient than turbo-charging
• Turbo-charge: compressor powered by exhaust turbine– More directly utilize exhaust energy– Turbo- lag problem– Affects exhaust treatment
• Intercooler– Increase charge density (hence output power) by cooling the
charge– Lowers NOx emissions– Suppresses knock
Additional benefit of turbo-charging
• Can downsize engine while retaining same max power– Less throttle loss under part load in SI engine
• Higher BMEP reduces relative friction and heat transfer losses
3
5
Engine Losses
1000 2000 3000 4000 5000Engine speed (rpm)
1
12
10
8
6
5
11
9
7
4
3
2
BM
EP
(b
ar)
Relative efficiency = 1
=0.88
=0.78 =0.70
=0.64
=0.58
=0.54
=0.50
4th gear,flat road
5th gear,flat road
3rd gear,flat road
Combustion speed, pumping lossHeat transfer
Th
rott
le +
ht
tran
sf +
fri
ctio
n
Spark retard/enrichment for SI;smoke limit for diesel
Data from SAE 910676;Saturn I4 engine
252g/KW-hr
288
324360
SI engine efficiency opportunity
Turbo DISI as enabling technology
– Fuel in-flight evaporation cools charge
More knock resistant
Issues– Knock
– Peak pressure
– Boosting capacity
– Cold start emissions
HC
PM0 1000 2000 3000
-2
0
2
4
6
8
10
12
BM
EP
(ba
r)
Speed (rpm)
Shift op. points up by downsizing
Regain load head room by
turbo-charging
Taurus FTPsec-by-sec
4
From Bosch Automotive Handbook
Charge-air pressure regulation with wastegate on exhaust gas end. 1.Engine, 2. Exhaust-gas turbochager, 3. Wastegate
T1= inlet temperature (K); P1= inlet pressure (bar); N = rev. per min.; = mass flow rate (kg/s)(From “Principles and Performance in Diesel Engineering,” Ed. by Haddad and Watson)
m“Corrected” Flow rate T1/P1m
Pre
ssur
e ra
tio
1
Compressor stall and surge
• Stall– Happens when incident flow angle is too large
(large V/Vx)– Stall causes flow blockage
• Surge– Flow inertia/resistance, and compression system
internal volume comprise a LRC resonance system– Oscillatory flow behave when flow blockage occurs
because of compressor stall reverse flow and violent flow rate surges
10
Turbine Map
Source: BorgWarner Turbo Systems
Mass flow
Efficiency
Compressor Turbine Matching Exercise
• For simplicity, take away intercooler and wastegate
• Given engine brake power output ( ) and RPM, compressor map, turbine map, and engine map
• Find operating point, i.e. air flow ( ), fuel flow rate ( ) turbo-shaft revolution per second (N), compressor and turbine pressure ratios (c and t) etc.
Engine
C T
mf QL
WE
mfma
1
2 3
4WE
11
Compressor/ turbine/engine matching
solution
1
c
12 c 1 2 c 1
c
a
Procedure:
1. Guess ; can get engine inlet conditions:
T P P T 1 T
2. Then engine volumetric efficiency calibration
will give the air flow m that can be '
a c
f
E f f E
swallowed'
3. From m and , the compressor speed N can be
obtained from the compressor map
4. The fuel flow rate m may be obtained from the
engine map:
W m LHV (RPM,W ,A/F)
5. Eng
3
M
Ea f p 3 a p 2 f L
M
t t
ine exhaust temperature T may be obtained from
energy balance (with known engine mech. eff. )
W (m m )c T m c T m LHV Q
6. Guess , then get turbine speed N from turbine map
and
1
t tt
c t t c t c
mass flow
7. Determine turbine power from turbine efficiency on map
1 W 1
8. Iterate on the values of and until W W and N N
Flow rate T/Pm
Pre
ssu
re r
atio
Compressor
Inter-Cooler
Engine
C T
Wastegate
Compressor/ Engine/ Turbine Matching
• Mass flows through compressor, engine, turbine and wastegate have to be consistent
• Turbine inlet temperature consistent with fuel flow and engine power output
• Turbine supplies compressor work
• Turbine and compressor at same speed
Compressor characteristics, with airflow requirements of a four-stroke truck engine superimposed.
(From “Principles and Performance in Diesel Engineering,” Ed. by Haddad and Watson)
12
Advanced turbocharger development
Electric assisted turbo-charging
• Concept– Put motor/ generator on
turbo-charger– reduce wastegate function
• Benefit– increase air flow at low
engine speed– auxiliary electrical output
at part load
Motor/Generator
Inter-Cooler
Engine
C T
Wastegate
Battery
Advanced turbocharger development
Electrical turbo-charger• Concept
– turbine drives generator; compressor driven by motor
• Benefit– decoupling of turbine and
compressor map, hence much more freedom in performance optimization
– Auxiliary power output
– do not need wastegate; no turbo-lag
Generator
Inter-Cooler
Engine
C TMotor
Battery
13
Advanced turbocharger development
Challenges
• Interaction of turbo-charging system with exhaust treatment and emissions– Especially severe in light-duty diesel market