529 ENGINE CONTROLS & STEERING PH: 902-566-1220 [email protected] SEASTAR BACK MOUNT KIT Teleflex SeaStar Back Mount Kit for Sea- Star Helm models HH5271-3 (8121105) and HH5272-3 (8121201) is used to reduce your helm's protrusion in ght quarters. Protrusion is reduced by a width equal to the thickness of the dash. Kit can also be used to retrofit the SeaStar 3" helm into 4.5" dash cutouts. PART NO. MFG# DESCRIPTION PRICE 8121125 HA5418 Back Mount Kit $58.35 HELM SERVICE KIT Kit includes: 1 ea. x Jam Nut 5/8" NF 1 ea. x Woodruff Key 1 ea. x Seal Ring 1 ea. x Top Plate 3 ea. x Screws For most BayStar and SeaStar Helms. PART NO. MFG# DESCRIPTION PRICE 8121103 HP6032 Service Kit $15.68 UNIVERSAL TIE-BARS Universal Tie-Bars used in a twin engine, single cylinder applicaon. Used on: HC5345-3 (8121340), HC5358-3 (8121346),17.5" long pin-to-pin Please see single & dual engine applicaon guide. PART NO. MFG# DESCRIPTION PRICE 8130156 HO6001 Universal Tie Bar $683.76 8130157 HO6003 Tie Bar $691.80 TWIN ENGINE DUAL CYLINDER TIE BAR For use with twin front mount cylinders in a twin engine/cylinder set up. Used on: HC5345-3 (8121340) HC5358-3 (8121346) 22" long pin-to-pin Please see single & dual engine applicaon guide. PART NO. MFG# DESCRIPTION PRICE 8130159 HO6002 Tie Bar for Twin $723.34 TWIN ENGINE SINGLE CYLINDER TIE BAR (HONDA) Honda Tie-Bar used in a twin engine, single cylinder applicaon Used on: HC5347-3 (8121345) Please see single & dual engine applicaon guide. PART NO. MFG# DESCRIPTION PRICE 8130158 HO5063 Tie Bar $722.69 8130156 8130157 SPACER KIT Spacer kit, for use with cylinder: HC5345-3 (8121340), HC5358-3 (8121346), and HC5348-3. Applied to: • 115-140 HP Suzuki • 25-60 HP Yamaha and Mercury • 115 HP Yamaha PART NO. MFG# DESCRIPTION PRICE 8121347 HO5090 Spacer Kit For Tie Bar $42.44 BULKHEAD FITTING ASSEMBLY Easily pass pipe, wires or cables through bulkheads and prevent carbon monoxide gases from passing from one enclosure to another. Designed to have a bolt on oval flange tube assembly with two oponal low durometer flexible boots as terminaon fixtures. These are secured by either hose clamps, or straps. 7537161 7537160 *SHOWN ASSEMBLED CABLE PROTECTOR Boot style black plasc cable protector, 4-1/2" base plate, approximately 3" High. Boot can be ghtened around cables. Aach the motor cable control boot without disturbing the cable set- ngs. Split the outer grommet and the inner ball in half by spling the secons. The inner ball is made of a low durometer soſt sealing material that allows the ball to swivel to its most efficient posion for easy cable operaon. The outer covers are made of marine grade composites, and the inner flange has a large area for bedding compound in the motor well or transom. White in colour. CONTROL CABLE SPLIT GROMMETS 8130171 8130175 8130174 8130173 8130172 Small Hole = .375" Large Hole = 1" PART NO. MFG# DESCRIPTION PRICE 8130171 1820W 1-1/2" Base, 1 Small Hole $10.23 8130172 1830W 1-1/2" Base, 1 Hole $15.39 8130173 1835W 1-1/2" Base, 3 Hole $15.39 8130174 1840W 2" Base, 1 Hole $15.39 8130175 1845W 2" Base, 3 Hole $15.39 PART NO. DESCRIPTION PRICE 8130170 Cable Protector $6.40 PART NO. MFG# DESCRIPTION PRICE 7537160 7730 Bulkhead Flange $29.23 7537161 7735 Bulkhead Tube $29.23