Endodontic Filling Materials

Endodontic Filling Materials

Qiang Zhu, DDS, PhD

The purpose of root canal filling:*Fill pulp space*Prevent microorganisms leakage and invasion*Protect exposed connective tissue wound surface*For the placement of post retention

1

Endodontic Filling Material RequirementsHandling:

* Easy to use and remove* Setting in an adequate time, allowing sufficient time for

obturation and x-ray control

Biological: * Antimicrobial* Sterile

* No general health problems or allergies. * No irritation and stimulation of the apical healing process.

2

Technical:* No shrinkage* No solubility in tissue fluids, no water absorption. * Good adhesion/adaptation to dentine or combining materials* No tooth discoloration* Radiopaque

Textbook of Endodontology, Bergenholtz, et al. 2003 3

Endodontic Filling MaterialI. Solid Materials

1. Gutta Percha2. Silver Cone3. Resilon4. Coated Cones

II. Sealers (Cements)

III. Materials for Root-End Filling

4

1. Gutta Percha phase: nature form; from the Taban tree

when cool slowly (1Fo/Hr) from melting phase; has better flow.

phase: most gutta percha cones; when cool normally from melting phase; less brittle than the -form From to when heated ~ 46 0C (115 0C)

Melt at 650C (1470C). Dissolved in Chloroform

I. Solid Materials

5

Gutta Percha Cone

70% Zinc Oxide20% Gutta Percha10% Metal sulfates, pigments,

wax, and resins

6

Gutta Percha Cone *Standardized Cores:

Used as master cone. #25, #30, etc. Taper 0.02mm/mm.

ANSI/ADA Spec.#57: tolerance +/- 0.05 mm !!!

*Accessory Cones:Used as accessory points in lateralcondensation. Such as Fine-fine, Medium-fine. Taper various.

7

*Greater taper cones: 4% or 6% used with special engine-driven rotary

instruments.

8

0.06 0.04 0.02

Carrier-Based (Thermafil):

Plastic or Titanium core coated with gutta percha

9

10

Obtura II:Thermoplasticized gutta-percha injection.Heat segment of gutta percha to 160 oC.

11

MicroSeal:Solid master cone and thermoplasticized gutta-percha injection.

12

2. Silver Cone (you may see)

Before After Re-treatment 1.5 years later

Removed Siler Cone 13

3. Resilon*A new synthetic resin-based polycaprolactone polymer.*Developed as a gutta-percha substitute to be used with a new resin sealer, Ephiphany.*Attempt to form an adhesive bond at the interface of the synthetic polymer-based core, the canal wall, and the sealer.

14

4. Coated ConesGutta percha cones coated with a resin, used with resin sealer

Gutta percha coated with glass ionomer, used with glass ionomer sealer.

Regular GP Active GP

ActivGP

Active GP Sealer

Dentin

15

II Endodontic Sealers* Bond gutta percha to root canal wall

* Fill space between gutta percha cones, and between cones and root canal wall

* Facilitate the seating gutta percha into the canal

Classification: *ZOE Sealers *Polymers

*Calcium Hydroxide Sealers*Glassionomer cement

*Others 16

Function of Endodontic Sealer

Sealer

Gutta perchaMasterCone

AccessoryCone

Canalwall Lateral

canal

17

ZOE SealersZinc Oxide, Eugenol, Resins etc. Harding is due to zinc eugenolate formation

Reasonable seal, antimicrobial, and long-lasting cytotoxicity.High humidity increases setting time.

* Rochert’s Sealer (Kerr Pulp Canal Sealer) * Tubliseal * Grossman’s Sealer * Procosol Cement * Wach’s Paste

18

Polymers

Best sealing; Freshly mixed cytotoxicity; once set, biocompatible;Antimicrobial effect decreased with increased setting time

* AH26 – Epoxyresin, ~34 hours (AHPlus ~ 8 hours)

* Diaket - Polyvinyl resin, ~ 7 min

* EndoFill - Silicone

19

Calcium Hydroxide Sealers

Release calcium hydroxide, may result in disintegration; Once set, no calcium hydroxide released; initial antibacterial effect.

* Sealapex - two paste, resin based

* CRCS Cement - power, liquid, Zinc oxide-eugenol based

* Apexit - power, liquid combination

20

Glassionomer Cement

Good biocompatibility, set too fast and hard to remove

* Ketec-Endo – Polycarboxylate working time in mouth ~ 7 min

21

III. Materials for Root-end Filling

*Amalgam, old material, easy to use

*Modified ZnOE cements: IRM

*Mineral Trioxide Aggregate (MTA)

*Composite (Gluma-Retroplast)

22

23

Evaluation of Biocompatibility of Root Canal Filling Materials

1. In vitro study on cell and tissue culture.

2. In vivo implantation in experimental animals- soft tissue or bone.

3. Usage evaluation when the material is used as intended - on experimental animals or humans.

24

In this lecture you should know:

*What is the most important requirement for root canal filling material?

*What is the composite of GP point (cone)?

*What is the tolerance of GP point?

*Which sealer belongs to which group?

*What is the two most used root-end filling materials?

Endodontic Lab Schedule Group A Group B Group C Group D

Tue 4/03/13 Access and preparation of anterior teeth1:00–5:00 PM

Wed 4/10/13 Obturation of anterior teeth1:00–5:00 AM

Tue 4/23/13 Access and preparation of maxillary premolar1:00–5:00 PM

Wed 4/24/13 Obturation of maxillary premolar1:00–5:00 PM

Tue 4/30/13 Rotary Instruments Access and prep. of max. molar 1:00–5:00 PM (A , B) (C, D)

Wed 5/01/13 Access and prep. of max. molar Rotary Instruments 1:00–5:00 PM (A , B) (C, D)

Mon 5/20/13 Obturation of max molar (A, B, C, D)8:00–12:00 AM

Tue 5/21/13 Makeup 1:00–5:00 PM

Wed 5/22/13 PRACTICAL EXAMINATION1:00–5:00 PM

?