EN ES FR ACCESSORY SHEET ACCESSORY AND INSTALLATION PARTS No. / N° Parts name (Q’ty) / Nombre de partes (Ctdad.) No. / N° Parts name (Q’ty) / Nombre de partes (Ctdad.) 1 Installation plate* x 1 Placa de instalación* x 1 7 Mounting screw** ø4 x 25 r x 6 Tornillo de montaje** ø4 x 25 r x 6 2 Wireless remote control* x 1 Control remoto* x 1 8 Pan head wood screw ø3.1 x 16 r x 2 Tornillo de cabeza de madera ø3,1 x 16 r x 2 3 Battery x 2 Pila x 2 9 Drain nipple*** x 1 (for heating model only) Codo de drenaje*** x 1 (sólo para el modelo de calefacción) 4 Remote control holder* x 1 Soporte del control remoto* x 1 ! Cap water proof x 2 (for some models only) Tapa impermeable x 2 (sólo para algunos modelos) 5 Nano-Silver Ginseng filter** Filtro Nano-Silver Ginseng** " Owner’s Manual, Installation Manual Manual del usuario, Manual de Instalación 6 Nano-Photo Copper Zinc filter** Filtro Nano-Photo Copper Zinc** # B Label x 1 (for Multi model) Etiqueta B x 1 (para el modelo Multi) * The part may differ from that shown. ** The number of parts may differ by model. *** The part is packed with the outdoor unit. 1110253177 Filter Clean / Replacement HOJA DE ACCESORIOS ACCESORIOS Y PIEZAS DE INSTALACIÓN Nano-Photo Copper Zinc filter Filtro Nano-Photo Copper Zinc Nano-Silver Ginseng filter Filtro Nano-Silver Ginseng Air filters Clean every 2 weeks. 1. Open the air inlet grille. 2. Remove the Nano-Silver Ginseng and Nano-Photo Copper Zinc filters if they are on filter. 3. Vacuum or wash and then dry them. 4. Reinstall the filters and close the air inlet grille. Nano-Silver Ginseng filter Maintaining your strong purifying and revitalizing filter. Clean every 6 months or when dust covers the filter. 1. Shake and blow with normal air or 2. Rinse the filter in water and dry it in under sunlight or in air. (Do not wash or rinse with high pressure water) 3. Replace every 3 years or sooner. (P/N: 42HQV9002, 42HQV9004 (Coverage)) Note: Ginseng scent will last up to 6 months. Nano-Photo Copper Zinc filter Maintaining your strong deodorizing filter. Clean every 6 months or when dust covers the filter. 1. Shake and blow with normal air or 2. Rinse the filter in water and dry it in under sunlight or in air. (Do not wash or rinse with high pressure water) 3. Replace every 3 years or sooner. (P/N: 42HQV9003, 42HQV9005 (Coverage)) Note: Filter life depends on the level of impurities in your operating environment. Higher levels of impurities may require more frequent cleaning and replacement. In all cases, we recommend an additional set of filters to improve the purifying and deodorizing performance of your air conditioner. * La pieza puede no coincidir con la que se muestra. ** El número de piezas puede cambiar según el modelo. *** La pieza se suministra con la unidad exterior. Limpieza / Reemplazo del filtro Filtros de aire Limpiar cada 2 semanas. 1. Abra la rejilla de la toma de entrada de aire. 2. Quite los filtros Nano-Silver Ginseng y Nano-Photo Copper Zinc si están colocados en el filtro de aire. 3. Aspírelos o lávelos y, después, séquelos. 4. Vuelva a instalar los filtros y cierre la rejilla de la toma de entrada de aire. Filtro Nano-Silver Ginseng Mantenimiento del filtro de purificación. Limpiar cada 6 meses o cuando el filtro esté cubierto de polvo. 1. Agite y airee el filtro con aire normal o 2. Introdúzcalo en agua y séquelo al sol o con aire caliente. (No utilice agua a presión ni lo ponga debajo del grifo) 3. Sustituir cada 3 años o antes. (P/N: 42HQV9002, 42HQV9004 (Cobertura)) Nota: La esencia de ginseng tiene una duración de 6 meses. Filtro Nano-Photo Copper Zinc Mantenimiento del filtro de desodorización. Limpiar cada 6 meses o cuando el filtro esté cubierto de polvo. 1. Agite y airee el filtro con aire normal o 2. Introdúzcalo en agua y séquelo al sol o con aire caliente. (No utilice agua a presión ni lo ponga debajo del grifo) 3. Sustituir cada 3 años o antes. (P/N: 42HQV9003, 42HQV9005 (Cobertura)) Nota: La vida útil del filtro depende del nivel de impurezas existente en el entorno de funcionamiento. Si los niveles de impurezas son elevados, tal vez sea necesario realizar la limpieza y el reemplazo con mayor frecuencia. En todos los casos, Se recomienda adquirir un conjunto adicional de filtros para mejorar el rendimiento de purificación y desodorización del aparato de aire acondicionado. FEUILLE D’ACCESSOIRES ACCESSOIRES ET ELEMENTS D’INSTALLATION N° Nom des pièces (Qté) N° Nom des pièces (Qté) 1 Plaque d’installation* x 1 7 Vis de montage** ø4 x 25 r x 6 2 Télécommande sans fil* x 1 8 Vis du panneau de télécommande ø3,1 x 16 r x 2 3 Pile x 2 9 Mamelon du drain*** x 1 (pour modèle avec chauffage uniquement) 4 Support de la télécommande* x 1 ! Bouchon étanche x 2 (pour certains modèles seulement) 5 Filtre Nano-Silver Ginseng** " Mode d’emploi, Manuel d’installation 6 Filtre Nano-Photo Copper Zinc** # Etiquette B x 1 (pour le modèle Multi) * Il est possible que la pièce soit différente de celle du présent schéma. ** Il est possible que le numéro de pièces varie d’un modèle à l’autre. *** Cette pièce est fournie avec l’unité extérieure. Nettoyage / Changement du filtre Filtres à air Nettoyez-les toutes les 2 semaines. 1. Ouvrez la grille d’entrée d’air. 2. Retirez les filtres Nano-Silver Ginseng et Nano-Photo Copper Zinc s’ils se trouvent sur le filtre. 3. Aspirez ou nettoyez les filtres, puis séchez-les. 4. Réinstallez les filtres et fermez la grille d’entrée d’air. Filtre Nano-Silver Ginseng Entretien de votre filtre fortement purifiant et revitalisant. Nettoyez tous les 6 mois ou lorsque le filtre est poussiéreux. 1. Secouez le filtre et aérez-le à l’air libre ou 2. Rincez le filtre sous l’eau et séchez-le à la lumière du soleil ou à l’air libre. (N’utilisez pas d’eau à forte pression pour laver ou rincer le filtre). 3. Remplacez-le au moins tous les 3 ans. (P/N: 42HQV9002, 42HQV9004 (Couverture)) Remarque: L’essence de ginseng dure 6 mois. Filtre Nano-Photo Copper Zinc Entretien de votre filtre désodorisant. Nettoyez tous les 6 mois ou lorsque le filtre est poussiéreux. 1. Secouez le filtre et aérez-le à l’air libre ou 2. Rincez le filtre sous l’eau et séchez-le à la lumière du soleil ou à l’air libre. (N’utilisez pas d’eau à forte pression pour laver ou rincer le filtre). 3. Remplacez-le au moins tous les 3 ans. (P/N: 42HQV9003, 42HQV9005 (Couverture)) Remarque: La durée de vie du filtre dépend du niveau d’impuretés du milieu d’utilisation. Vous devrez probablement nettoyer et remplacer le filtre plus souvent en cas de niveaux élevés d’impuretés. Dans tous les cas, Nous vous recommandons d’utiliser des filtres complémentaires qui vous permettront d’optimiser les effets purifiants et désodorisants de votre climatiseur. Filtre Nano-Photo Copper Zinc Filtre Nano-Silver Ginseng 1110253177.indd 1 1/16/09 5:41:12 PM
2
Embed
EN ES FR ACCESSORY SHEET HOJA DE ACCESORIOS FEUILLE D ...ccac.com.ph/brands/pdf/10702bae-552e-49f7-adc3-e7b4ae5c74b1.pdf · *** Alat ini dibungkus bersama dengan unit luaran. Membersih
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
EN ES FR
ACCESSORY SHEETACCESSORY AND INSTALLATION PARTS
No. / N° Parts name (Q’ty) / Nombre de partes (Ctdad.) No. / N° Parts name (Q’ty) / Nombre de partes (Ctdad.)
1Installation plate* x 1
Placa de instalación* x 1
7 Mounting screw** ø4 x 25 r x 6Tornillo de montaje** ø4 x 25 r x 6
2 Wireless remote control* x 1Control remoto* x 1
8 Pan head wood screw ø3.1 x 16 r x 2Tornillo de cabeza de madera ø3,1 x 16 r x 2
3 Battery x 2Pila x 2
9Drain nipple*** x 1 (for heating model only)
Codo de drenaje*** x 1 (sólo para el modelo de calefacción)
4Remote control holder* x 1
Soporte del control remoto* x 1
!Cap water proof x 2 (for some models only)
Tapa impermeable x 2 (sólo para algunos modelos)
5Nano-Silver Ginseng fi lter**Filtro Nano-Silver Ginseng**
"Owner’s Manual, Installation Manual
Manual del usuario, Manual de Instalación
6Nano-Photo Copper Zinc fi lter**Filtro Nano-Photo Copper Zinc**
#B Label x 1 (for Multi model)
Etiqueta B x 1 (para el modelo Multi)
* The part may differ from that shown.** The number of parts may differ by model.*** The part is packed with the outdoor unit.
1110253177
Filter Clean / Replacement
HOJA DE ACCESORIOSACCESORIOS Y PIEZAS DE INSTALACIÓN
Nano-Photo Copper Zinc fi lterFiltro Nano-Photo Copper Zinc
Nano-Silver Ginseng fi lterFiltro Nano-Silver Ginseng
Air fi ltersClean every 2 weeks. 1. Open the air inlet grille. 2. Remove the Nano-Silver Ginseng and Nano-Photo Copper Zinc fi lters if they
are on fi lter. 3. Vacuum or wash and then dry them. 4. Reinstall the fi lters and close the air inlet grille.Nano-Silver Ginseng fi lterMaintaining your strong purifying and revitalizing fi lter.Clean every 6 months or when dust covers the fi lter. 1. Shake and blow with normal air or 2. Rinse the fi lter in water and dry it in under sunlight or in air. (Do not wash or rinse with high pressure water) 3. Replace every 3 years or sooner. (P/N: 42HQV9002, 42HQV9004 (Coverage))Note: Ginseng scent will last up to 6 months.Nano-Photo Copper Zinc fi lterMaintaining your strong deodorizing fi lter.Clean every 6 months or when dust covers the fi lter. 1. Shake and blow with normal air or 2. Rinse the fi lter in water and dry it in under sunlight or in air. (Do not wash or rinse with high pressure water) 3. Replace every 3 years or sooner. (P/N: 42HQV9003, 42HQV9005 (Coverage))Note: Filter life depends on the level of impurities in your operating environment.
Higher levels of impurities may require more frequent cleaning and replacement. In all cases, we recommend an additional set of fi lters to improve the purifying and deodorizing performance of your air conditioner.
* La pieza puede no coincidir con la que se muestra.** El número de piezas puede cambiar según el modelo.*** La pieza se suministra con la unidad exterior.
Limpieza / Reemplazo del fi ltroFiltros de aireLimpiar cada 2 semanas. 1. Abra la rejilla de la toma de entrada de aire. 2. Quite los fi ltros Nano-Silver Ginseng y Nano-Photo Copper Zinc si están
colocados en el fi ltro de aire. 3. Aspírelos o lávelos y, después, séquelos. 4. Vuelva a instalar los fi ltros y cierre la rejilla de la toma de entrada de aire.Filtro Nano-Silver GinsengMantenimiento del fi ltro de purifi cación.Limpiar cada 6 meses o cuando el fi ltro esté cubierto de polvo. 1. Agite y airee el fi ltro con aire normal o 2. Introdúzcalo en agua y séquelo al sol o con aire caliente. (No utilice agua a presión ni lo ponga debajo del grifo) 3. Sustituir cada 3 años o antes. (P/N: 42HQV9002, 42HQV9004 (Cobertura))Nota: La esencia de ginseng tiene una duración de 6 meses.Filtro Nano-Photo Copper ZincMantenimiento del fi ltro de desodorización.Limpiar cada 6 meses o cuando el fi ltro esté cubierto de polvo. 1. Agite y airee el fi ltro con aire normal o 2. Introdúzcalo en agua y séquelo al sol o con aire caliente. (No utilice agua a presión ni lo ponga debajo del grifo) 3. Sustituir cada 3 años o antes. (P/N: 42HQV9003, 42HQV9005 (Cobertura))Nota: La vida útil del fi ltro depende del nivel de impurezas existente en el entorno
de funcionamiento. Si los niveles de impurezas son elevados, tal vez sea necesario realizar la limpieza y el reemplazo con mayor frecuencia. En todos los casos, Se recomienda adquirir un conjunto adicional de fi ltros para mejorar el rendimiento de purifi cación y desodorización del aparato de aire acondicionado.
FEUILLE D’ACCESSOIRESACCESSOIRES ET ELEMENTS D’INSTALLATION
N° Nom des pièces (Qté) N° Nom des pièces (Qté)
1Plaque d’installation* x 1
7 Vis de montage** ø4 x 25 r x 6
2 Télécommande sans fi l* x 1 8 Vis du panneau de télécommande ø3,1 x 16 r x 2
3 Pile x 2 9Mamelon du drain*** x 1 (pour modèle avec chauffage
uniquement)
4Support de la télécommande* x 1
!Bouchon étanche x 2 (pour certains modèles seulement)
5Filtre Nano-Silver Ginseng**
"Mode d’emploi, Manuel d’installation
6Filtre Nano-Photo Copper Zinc**
#Etiquette B x 1 (pour le modèle Multi)
* Il est possible que la pièce soit différente de celle du présent schéma.** Il est possible que le numéro de pièces varie d’un modèle à l’autre.*** Cette pièce est fournie avec l’unité extérieure.
Nettoyage / Changement du fi ltreFiltres à airNettoyez-les toutes les 2 semaines. 1. Ouvrez la grille d’entrée d’air. 2. Retirez les fi ltres Nano-Silver Ginseng et Nano-Photo Copper Zinc s’ils se trouvent sur le fi ltre. 3. Aspirez ou nettoyez les fi ltres, puis séchez-les. 4. Réinstallez les fi ltres et fermez la grille d’entrée d’air.Filtre Nano-Silver GinsengEntretien de votre fi ltre fortement purifi ant et revitalisant.Nettoyez tous les 6 mois ou lorsque le fi ltre est poussiéreux. 1. Secouez le fi ltre et aérez-le à l’air libre ou 2. Rincez le fi ltre sous l’eau et séchez-le à la lumière du soleil ou à l’air libre. (N’utilisez pas d’eau à forte pression pour laver ou rincer le fi ltre). 3. Remplacez-le au moins tous les 3 ans. (P/N: 42HQV9002, 42HQV9004 (Couverture))Remarque: L’essence de ginseng dure 6 mois.Filtre Nano-Photo Copper ZincEntretien de votre fi ltre désodorisant.Nettoyez tous les 6 mois ou lorsque le fi ltre est poussiéreux. 1. Secouez le fi ltre et aérez-le à l’air libre ou 2. Rincez le fi ltre sous l’eau et séchez-le à la lumière du soleil ou à l’air libre. (N’utilisez pas d’eau à forte pression pour laver ou rincer le fi ltre). 3. Remplacez-le au moins tous les 3 ans. (P/N: 42HQV9003, 42HQV9005 (Couverture))Remarque: La durée de vie du fi ltre dépend du niveau d’impuretés du milieu d’utilisation. Vous devrez probablement nettoyer et remplacer le fi ltre plus souvent
en cas de niveaux élevés d’impuretés. Dans tous les cas, Nous vous recommandons d’utiliser des fi ltres complémentaires qui vous permettront d’optimiser les effets purifi ants et désodorisants de votre climatiseur.
Filtre Nano-Photo Copper Zinc
Filtre Nano-Silver Ginseng
1110253177.indd 1 1/16/09 5:41:12 PM
MA ID
LEMBARAN AKSESORIALAT TAMBAH DAN BAHAGIAN-BAHAGIAN PEMASANGAN
No. / No. Nama bahagian (Kuantiti) / Nama suku cadang (Jumlah) No. / No. Nama bahagian (Kuantiti) / Nama suku cadang (Jumlah)
1Plat pemasangan* x 1
Pelat pemasangan* x 1
7 Skru pemasang** ø4 x 25 r x 6Sekrup pemasangan** ø4 x 25 r x 6
2 Alat kawalan jauh tanpa wayar* x 1Remot kontrol tanpa kabel* x 1
8 Skru kayu kepala datar ø3,1 x 16 r x 2Sekrup kayu berkepala panci ø3,1 x 16 r x 2
3 Bateri x 2Baterei x 2
9Puting saliran*** x 1 (untuk model pemanasan sahaja)
Nipel pipa saluran pembuangan*** x 1 (untuk model hanya pemanasan)
4Penyangkut alat kawalan jauh* x 1
Pemegang remot kontrol* x 1
!Tukup kalis air x 2 (untuk sesetengah model sahaja)
Tutup anti air x 2 (untuk model tertentu saja)
5Penapis Nano-Silver Ginseng**
Penyaring Nano-Silver Ginseng**
"Buku panduan pengguna, Buku panduan pemasangan
Buku petunjuk pemilik, Petunjuk pemasangan
6Penapis Nano-Foto Tembaga Zink*
Penyaring Nano-Photo Copper Zinc**
#Label B x 1 (untuk model Multi)Label B x 1 (untuk model Multi)
* Alat ini mungkin berbeza daripada yang ditunjukkan.** Bilangan alat mungkin berbeza mengikut model.*** Alat ini dibungkus bersama dengan unit luaran.
Membersih / Menggantikan Penapis
LEMBAR AKSESORIAKSESORI DAN SUKU CADANG PEMASANGAN
Penapis udaraBersihkan setiap 2 minggu. 1. Buka jeriji saluran masuk udara. 2. Tanggalkan penapis Nano-Silver Ginseng dan penapis Nano-Foto
Tembaga Zink sekiranya ia berada pada penapis udara. 3. Vakum atau cuci dan kemudian keringkan. 4. Pasang semula penapis tersebut dan tutup jeriji saluran masuk udara.Penapis Nano-Silver GinsengMenyelenggara penapis penulenan kuat dan menyegarkan semula.Bersihkan setiap 6 bulan atau bila debu menutupi penapis. 1. Goncang dan hembus dengan udara biasa atau 2. Bilas penapis dalam air dan keringkannya di bawah cahaya matahari atau
dalam udara. (Jangan cuci atau bilas dengan air tekanan tinggi) 3. Gantikan setiap 3 tahun atau lebih awal. (P/N:42HQV9002, 42HQV9004 (Liputan))Nota: Bauan ginseng akan kekal selama 6 bulan.Penapis Nano-Foto Tembaga ZinkMenyenggarakan penapis nyahbau anda yang kuat.Bersihkan setiap 6 bulan atau bila debu menutupi penapis. 1. Goncang dan hembus dengan udara biasa atau 2. Bilas penapis dalam air dan keringkannya di bawah cahaya matahari atau
dalam udara. (Jangan cuci atau bilas dengan air tekanan tinggi) 3. Gantikan setiap 3 tahun atau lebih awal. (P/N:42HQV9003, 42HQV9005 (Liputan))Nota: Hayat penapis bergantung kepada tahap kotoran dalam persekitaran di
mana anda mengendalikannya. Tahap kotoran yang tinggi memerlukan penapis dibersih dan digantikan dengan lebih kerap. Dalam semua keadaan, Kami mengesyorkan set penapis tambahan bagi meningkatkan prestasi penulenan dan penyahbauan alat penyaman udara anda.
* Komponen ini mungkin berbeda dari yang diperlihatkan.** Jumlah komponen dapat berbeda sesuai model.*** Komponen ini dikemas bersama unit luar-ruang.
Pembersihan / Penggantian PenyaringPenyaring udaraBersihkan setiap 2 minggu. 1. Buka gril saluran masuk udara. 2. Lepaskan penyaring Nano-Silver Ginseng dan Nano-Photo Copper Zinc jika
ada dalam penyaring udara. 3. Bersihkan dengan vakum atau cuci dan kemudian keringkan penyaring
tersebut. 4. Pasang kembali penyaring dan tutup gril saluran masuk udara.Penyaring Nano-Silver GinsengMemelihara kemampuan penyaring pembersih dan penyegar.Bersihkan setiap 6 bulan atau jika debu sudah menutupi fi lter. 1. Kocok dan tiuplah dengan udara normal atau 2. Bilas penyaring di dalam air lalu keringkan di bawah sinar matahari atau
dengan dianginkan. (Jangan cuci atau bilas dengan air bertekanan tinggi) 3. Ganti setiap 3 tahun atau kurang. (P/N:42HQV9002, 42HQV9004 (Cakupan))Catatan: Bau ginseng akan hilang setelah 6 bulan.Penyaring Nano-Photo Copper ZincMempertahankan kekuatan fi lter penghilang bau.Bersihkan setiap 6 bulan atau jika debu sudah menutupi fi lter. 1. Kocok dan tiuplah dengan udara normal atau 2. Bilas penyaring di dalam air lalu keringkan di bawah sinar matahari atau
dengan dianginkan. (Jangan cuci atau bilas dengan air bertekanan tinggi) 3. Ganti setiap 3 tahun atau kurang. (P/N:42HQV9003, 42HQV9005 (Cakupan))Catatan: Masa pakai penyaring tergantung pada tingkat kekotoran dalam
lingkungan pengoperasian Anda. Tingkat kekotoran yang lebih tinggi mungkin memerlukan pembersihan dan penggantian yang lebih sering. Dalam semua keadaan, Kami sarankan Anda agar menggunakan fi lter tambahan untuk meningkatkan kemampuan penyejuk udara dalam memurnikan udara dan menghilangkan bau.
* Bộ phận có thể khác với hình vẽ.** Số các bộ phận có thể khác nhau theo kiểu máy.*** Bộ phận được đóng gói vói máy ngoài trời.
Lám sạch / Thay thế Bộ lọcCác bộ lọc không khiLám sạch 2 tu�n một l�n. 1. Mở miếng lưới sắt bảo vệ đường khí vào. 2. Tháo các bộ lọc Nano-Silver Ginseng và Nano-Photo Copper Zinc ra
nếu chúng đang ở trên bộ lọc. 3. Hùt bụi hoặc rửa sạch và sau đó để khô. 4. Lắp đặt lại các bộ lọc và đóng miếng lưới sắt bảo vệ đường khí vào.Bộ lọc Nano-Silver GinsengBảo trì bộ lọc mạnh mẽ tinh khiết và tái sinh của bạn.Lau chùi mỗi 6 tháng hay khi có bụi bao phủ bộ lọc. 1. Lắc và thổi bằng không khí thường hoặc 2. Rửa sạch bộ lọc bằng nước và hong khô dưới nắng hay không khí.
(Đừng rửa hay giặt bằng nước áp lực cao) 3. Thay thế sau mỗi 3 năm hoặc sớm hơn. (P/N:42HQV9002, 42HQV9004 (Bao))Chủ ý: Hưng nhân sâm sẽ kéo dài 6 tháng.Bộ lọc Nano-Photo Copper ZincBảo trì bộ lọc khử̄ mùi mạnh của bạn.Lau chùi mỗi 6 tháng hay khi có bụi bao phủ bộ lọc. 1. Lắc và thổi bằng không khí thường hoặc 2. Rửa sạch bộ lọc bằng nước và hong khô dưới nắng hay không khí.
(Đừng rửa hay giặt bằng nước áp lực cao) 3. Thay thế sau mỗi 3 năm hoặc sớm hơn. (P/N:42HQV9003, 42HQV9005 (Bao))Chủ ý: Thới gian t�n tại của bộ lọc phụ thuộc vào mức độ của các tạp chất
trong mợi trường hoạt động của bạn. Mức độ tạp chất cao có thể c�n làm sạch và thay thế thường xuyên hơn. Trong mọi trường hợp, Chủng tôi khuyến nghị một bộ đ�; lọc bổ sung để cải thiện công suất tinh chế và khử mùi của máy đi�u hòa của bạn.
CT
附件單
附件和安裝零部件
編號 / Số 部件名稱(數量) / Tên phụ tʻ ng (Số lượng) 編號 / Số 部件名稱(數量) / Tên phụ tʻ ng (Số lượng)
1安裝板* x 1
Tấm vỉ láp đắt máy* x 1
7 安置螺釘** ø4 x 25 r x 6Vít treo máy** ø4 x 25 r x 6
2 無線遙控器* x 1Bộ đi�u khiển từ xa* x 1
8 盤頭木螺釘 ø3,1 x 16 r x 2Vít gố mũ chóp cục ø3,1 x 16 r x 2
3 電池 x 2Pin x 2
9排水接頭*** x 1 (僅限加熱型)
Vòt tháo nước*** x 1 (chỉ đối với kiểu máy sưởi ấm)