EMERSON MODEMS

Emerson Modem Programming Procedure:‐ Airtel Africa Project Page : 1 of 12

EMERSON Programming procedureEMERSON Programming procedure for GPRS MODEM

Made by Mr. Arjun Patil Date : 25.06.2012 Version: 1.0

Procedure for downloading Software into EMERSON IPMS Modem:


Procedure for downloading Software into EMERSON IPMS Modem:• Step 1. : Tools requirement : PICkit 2 programmer , Fluke Multimeter, Tester, 2 core 0.15

Sq.MM cu. Flexible cable for 5 Vdc supply , Solder Gun with Soldering wire, Modem , Modem Athena , 12Vdc Supply connector in IPMS system, Laptop with RS232 connector, Hyper terminal Software in Laptop, Pickit 2 Software for Program download into IPMS Modem etc.

5Vdc Supply From5Vdc Supply From SVR PCB to MODEM

IPMS MODEM 5Vdc Supply Connection


pp y

RS232 Connection from EMU Controller PCB

12Vdc Supply from SMPS PCB

J9 Connector pin 2: 5Vdc & Pin 3 : GNDPin 3 : GND

SIM300DZ

Antenna

Back Side of IPMS MODEM Front Side of IPMS MODEM

Note : 5Vdc External supply connection taken from SVR Connector CN1 pin 115 GND and Pin 116 5Vdc

5VDC External Supply from SVR PCB Emerson Modem Programming Procedure:‐ Airtel Africa Project Page : 4 of 12

PIC kit 2 hardware information Details for Procurement


1. Copy file on desktop of Laptop and file name is as GSE0_1_3a.hex2 Please note Kindly installation PICkit 2 software first in your laptop (Laptop should2. Please note Kindly installation PICkit 2 software first in your laptop.(Laptop should

required RS232 port) Following is the required programmer for MODEM up‐gradation. http://www.microchipdirect.com/ProductDetails.aspx?Catalog=BuyMicrochip&Category=PIhttp://www.microchipdirect.com/ProductDetails.aspx?Catalog BuyMicrochip&Category PICKit%20Debugger%20or%20Programmer&mid=13&treeid=6Part num Part Number: PG164120 ‐ PICkit 2 Microcontroller ProgrammergOr http://search.digikey.com/us/en/products/PG164130/PG164130‐ND/2171224

3. Software for http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en023073Check bottom of the pagepikkit2 programmer 1mb to 1.9mb only

AAA. Program procedure Emerson Modem Programming Procedure:‐ Airtel Africa Project Page : 6 of 12

g p

1 St IPMS 48Vd S l f CB8 MCB • 1. Stop IPMS 48Vdc Supply from CB8 MCB • 2. Connect 5VDC supply cable from SVR CN1 (115 = +5Vdc and 116 =

GND cable ) to GPRS Modem at J9 connector on pin2 = +5vdc and pin 3=GNDpin 3=GND.

• 3. Insert SIM into Modem.• 4. Connect 48Vdc to Modem to Modem.

5 C t R 232 D t bl t M d• 5. Connect Rs232 Data cable to Modem.• 6. Connect PICkit 2 programmer to Modem on J9 connector pin 1 to

Pin5 and Pin 6 is open.• 7 St t 48Vd l b it h MCB CB8 i IPMS• 7. Start 48Vdc supply by switch on MCB CB8 in IPMS.• 8. Start program like start and go to PICkit 2 v2.40

• (Kindly check Back side of Modem Type like SIM300DZ or 900D • because this program is for 300DZ SIM Modem only)


Check here Device is not connected if it connected then it will showif it connected then it will show PIC18F6722

D i ti h k G t T l d h k i tiDevice connection checkup: Go to Tools and check communication


• 9. First Erase old program of Modem by click to Erase OptionOption.

• 10. Erasing device .. Complete message will get like this.

• 10. After Erasing and go to File and import new program save on desktop is as GSE0 1 3a hexon desktop is as GSE0_1_3a.hex then you will get message is as Hex file successfully imported.

• 11. click on write then PICkit 2 will write program into GPRM Modem.Modem.


12. Once program get done then message will get like is as Programming successful.

13. Check program successful done or not by clicking verify option and you will get option and you will get message like is as Verification successful

14. Now remove PICkit 2 hardware kit from Modem.

15. Stop 48Vdc supply from CB8 MCB.

16. Remove 5Vdc supply cable from SVR PCB and Modem.

17 S 48Vd S l b 17. Start 48Vdc Supply by switching ON CB8 MCB

BBB Do Some Setting in IPMS DisplayEmerson Modem Programming Procedure:‐ Airtel Africa Project Page : 10 of 12

BBB. Do Some Setting in IPMS DisplayPlease note IPMS password is as 1111

7. Set Phone no's : 2 and 3 line item only e.g. mobile no is as +255 786147299 then put no is as 0 7861472990 and save it by pressing enter key7861472990 and save it by pressing enter key

8. Set IP address: 10.087.160.2529. Set Site ID : MEZNGAA123 ( Take Site ID from Airtel)10 Set Port ID: 818910.Set Port ID: 818911.Version Number: 118

CCC Testing of IPMS Alarm by GPRS MODEM


CCC. Testing of IPMS Alarm by GPRS MODEM

h l f b h• 1. Switch on 48VDc supply of IPMS by switching CB8 MCB.• 2. check GPRS Modem LED is getting blinking or not (If not then SIM card

is not getting register but wait for 30Sec to register)g g g g )• 3. set wrong port ID like 0189 and save it• 4. Remove battery voltage from DG HMI board and wait for 5 Minutes to

S S i S di lget SMS as per set into IPMS display.

Concern regards GPRS ModemEmerson Modem Programming Procedure:‐ Airtel Africa Project Page : 12 of 12

Concern regards GPRS Modem

Thank you…………………Thank you…………………

EMERSON MODEMS

Documents