GND +VIN GND Door Strike Input Input Ground Ground Normally Closed Contact Common Contact Door Status Normally Open Contact Common Contact REX Door Strike P/S (+) (+) (-) (-) Transorb (Voltage Supression), Siemens S10K30 or equiv. Maglock (Battery backed) Strike P/S (Battery backed) Door A Door B CABLING INFORMATION Ref. Connection Conductors A.W.G Gauge Max ft. A RS-485 Communications Cable 4* #24 4000** (1220 m) B Proximity Reader to EMC 6 #22 500 (152 m) C Door Strike to EMC 2 #18 500 (152 m) D REX to EMC 2 #22 1000 (305 m) E Door Status Contact 2 #22 500 (152 m) -All cabling must be stranded with overall shielding. -Ground all (except RS-485) cable shield/drain wires to ground screw in cabinet. Follow open-ended grounding method (i.e., tape back shield/drain wire at other end). *One conductor not used from one of RS-485 twisted pairs. **End to end. (or) (Back of Board) C C D E Reader A Reader B COM IN COM OUT +LOC ALM -LOC ALM COM NORM OPEN NORM CLOSED REX REX DOOR STAT DOOR STAT +LOC ALM -LOC ALM COM NORM OPEN NORM CLOSED REX REX DOOR STAT DOOR STAT +LOC ALM -LOC ALM COM NORM OPEN NORM CLOSED REX REX DOOR STAT DOOR STAT +LOC ALM -LOC ALM COM NORM OPEN NORM CLOSED REX REX DOOR STAT DOOR STAT +5 W1 +12 (see detail) L1 RD 0 RD 1 P O W E R Door Strike or Maglock (Reader voltage jumper selected at factory) NOTE: See Reader Manufacturer's wiring specifications for LED Control Info. Proximity Reader B Diode (1N4004 or equiv.) for Counter EMF protection W3 Jumper (Factory-set as shown) (Do not Change) Transorb (Voltage Supression), Siemens S10K30 or equiv. Diode (1N4004 or equiv.) for Counter EMF protection For a Stand-Alone System: Keep W2 jumper in TIN position. For a Multi-EMC System: refer to other side of sheet. Door Sense A L7 Activity Light L5 Tamper Switch L6 N/A L4 REX B L2 REX A L3 Door Sense B EMC Address Dipswitching (EMCs must be sequentially addressed starting with Address 1) (Top part of Front of Board) RX TX TP3 +12V TP4 +5V W2 Jumper TOUT TIN EM3000 Page 1 For multi-EMC config. instructions, refer to to the other side. (Bottom part of Front of Board) 1540F1 Doc 6001540, Rev D RS232-485 CONVERTER A Red w/white stripe Black BATTERY Backed/Regulated 1.0 Amp @ 12 VDC Power Supply Board Ground Neutral Hot GRN WHT BLK To 110 VAC at Junction Box or Breaker Panel TB1 TB2 + IN - + OUT - Output + - C Red Black Low Voltage Disconnect Module + -
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
DATA
1
GN
D+V
ING
ND
Door Strike
Input
Input
Ground
Ground
NormallyClosed Contact
CommonContact
DoorStatus
NormallyOpen Contact
CommonContact
REX
DoorStrikeP/S (+)
(+)
(-)
(-)
Transorb (Voltage Supression),Siemens S10K30 or equiv.
Maglock
(Batterybacked)
StrikeP/S
(Batterybacked)
Door A
Door B
CABLING INFORMATION
Ref. Connection Conductors A.W.G Gauge Max ft.
A RS-485 Communications Cable 4* #24 4000** (1220 m)
B Proximity Reader to EMC 6 #22 500 (152 m)
C Door Strike to EMC 2 #18 500 (152 m)
D REX to EMC 2 #22 1000 (305 m)
E Door Status Contact 2 #22 500 (152 m)
-All cabling must be stranded with overall shielding.-Ground all (except RS-485) cable shield/drain wires to ground screw in cabinet. Follow open-ended grounding method (i.e., tape back shield/drain wire at other end).*One conductor not used from one of RS-485 twisted pairs.**End to end.
(or)(Back of Board)
Quick Installation Guide
C
C
D E
Reader A
Reader B
COM IN
COM OUT
+LOCALM
-LOCALMCOMNORMOPENNORMCLOSEDREX
REX
DOOR STAT
DOOR STAT
+LOCALM
-LOCALMCOMNORMOPENNORMCLOSEDREX
REX
DOOR STAT
DOOR STAT
+LOCALM
-LOCALMCOMNORMOPENNORMCLOSEDREX
REX
DOOR STAT
DOOR STAT
+LOCALM
-LOCALMCOMNORMOPENNORMCLOSEDREX
REX
DOOR STAT
DOOR STAT
+5W1+12
(see detail)
L1 RD0
RD1
POWER
Door Strike or Maglock
(Reader voltage jumper selected at factory)
NOTE: See Reader Manufacturer's wiring specifications forLED Control Info.
Proximity Reader
BSHIELD
SHIELD
Diode (1N4004 or equiv.)for Counter EMFprotection
(see NOTE)
W3 Jumper
(Factory-set as shown)(Do not Change)
Transorb (Voltage Supression),Siemens S10K30 or equiv.
Diode (1N4004 or equiv.)for Counter EMFprotection
For a Stand-AloneSystem: Keep W2 jumper in TIN position.For a Multi-EMC System: refer to other side of sheet.
DoorSense A
L7
ActivityLight
L5
TamperSwitch
L6
N/A
L4
REX B
L2
REX A
L3
DoorSense B
EMC AddressDipswitching(EMCs must be sequentiallyaddressed starting withAddress 1)
(Top part of Front of Board)
RX TXTP3 +12V
TP4 +5V
W2Jumper
TOUT
TIN
EM3000Page 1For multi-EMC config.
instructions, refer toto the other side.
(Bottom part ofFront of Board) EMC 1
1540F1 Doc 6001540, Rev D
RS232-485 CONVERTER
A-
B+
RTN
GND
TB1+12V
+ 12V
GND
(B+)
(A-)
RTN
To PC Case Screw
One Conductor
From Second
Twisted Pair.
Other Conductor
Not Used.
A
One Twisted Pair
Attach Shield/Drain wireto any case screwon back of PC.
COMlocationwill vary
PORTRS-485
ConverterCOM
Red w/white stripeBlack
BATTERYBacked/Regulated1.0 Amp @ 12 VDC
Power Supply Board
GroundNeutral
Hot
GRNWHTBLK
To 110 VACat Junction Box orBreaker Panel
TB1
TB2
+IN-
+OUT-
Output
+ - CRedBlack
Low VoltageDisconnect Module
+-
NOTE:See ReaderManufacturer'swiring specificationsfor LED control info.
1540F2
EMC 2
EMC 1 EMC 2EMC Address
Dipswitching For additionaladdressing, refer to theEM3000 InstallationManual.
OFF
ON
OFF
ON
(For a multi-EMC system,the EMC boards must beaddressed in order, startingwith Address 1).
EMC 1
OFF
ON
Page 2
EM3000
All except last EMC in amulti-EMC system.
Stand-alone; or last EMC in amulti-EMC system.
OFF
ON
to EMC 3and above
SHIELD
SHIELD SHIELD
SHIELD
RS-485 Connection
(see NOTE)
W3 Jumper
(Factory-set as shown)(Do not Change)
W3 Jumper
(Factory-set as shown)(Do not Change)
CABLING INFORMATION
Ref. Connection Conductors A.W.G Gauge Max ft.
A RS-485 Converter to last EMC 4* #24 4000** (1220 m)
B Proximity Reader to EMC 6 #22 500 (152 m)
C Door Strike to EMC 2 #18 500 (152 m)
D REX to EMC 2 #22 1000 (305 m)
E Door Status Contact 2 #22 500 (152 m)
-All cabling must be stranded with overall shielding.-Ground all (except RS-485) cable shield/drain wires to ground screw in cabinet. Follow open-ended grounding method (i.e., tape back shield/drain wire at other end).*One conductor not used from one of RS-485 twisted pairs.**End to end.
A
RS232-485 CONVERTER
A-
B+
RTN
GND
TB1+12V
+ 12V
GND
(B+)
(A-)
RTN
To PC Case Screw
One Conductor
From Second
Twisted Pair.
Other Conductor
Not Used.
A
One Twisted Pair
Attach Shield/Drainwire to any casescrew on backof PC.
COMlocationwill vary
PORTRS-485
Converter
Red w/white stripeBlack
BATTERYBacked/Regulated1.0 Amp @ 12 VDC
Power Supply Board
GroundNeutral
Hot
GRNWHTBLK
To 110 VACat Junction Box orBreaker Panel
TB1
TB2
+IN-
+OUT-
Output
+ - CRedBlack
Low VoltageDisconnect Module
+-
Red w/white stripeBlack
BATTERYBacked/Regulated1.0 Amp @ 12 VDC
Power Supply Board
GroundNeutral
Hot
GRNWHTBLK
To 110 VACat Junction Box orBreaker Panel
TB1
TB2
+IN-
+OUT-
Output
+ - CRedBlack
Low VoltageDisconnect Module
+-
Related Documents
![User Hand Book EM3000[1]](https://static.cupdf.com/doc/110x72/55cf9c06550346d033a84a44/user-hand-book-em30001.jpg)
