Electrical Safety in the Workplace NFPA 70 E Presented by Sabine Mueller
Electrical Safety in the Workplace
NFPA 70 E
Presented by Sabine Mueller
What Made Sabine Choose Such a DRY Topic?
Ulterior MotiveMetso Mueller Engineering has been visiting many scrap yards two or more times per year for >30 years. We work on medium/high voltage drive motors.
When we are working at your plant Metso has a legal obligation to provide a safe workplace for our technicians. As the host company YOU are also legally obligated to provide a safe workplace.
What is NFPA 70E and what does it have to do with OSHA & the National Electric Code?
NFPA NEC
OSHA1970 Congress passed the OSH Act, which created the Occupational Safety and Health Administration, OSHA is part of the Labor Department.
OSHA GENERAL DUTY CLAUSE
The mission of the international nonprofit NFPA, established in 1896, is to reduce the worldwide burden of fire and other hazards on the quality of life by providing and advocating consensus codes and standards, research, training and education.
The NEC is developed by an NFPA committee, which is then approved by the American National Standards Institute, ANSI.
The NEC’s is created primarily for those who design, install and inspect electrical installations. The National Electric Codes does not necessarily apply to workplace or employee safety.
In 1975 NFPA recommended to OSHA that a document be prepared applicable to electrical safety. The document was created by extracting pertinent information from the NEC and other sources.
The first edition of the NFPA 70 E was published in 1979
NFPA 70 E
WHO DOES IT APPLY TO ?
WHAT VOLTAGE LEVEL DOES IT APPLY TO?
NFPA 70 E DETAILS FOUR PROTECTIVESTRATEGIES TO REDUCE THE RISK OF INJURYWHEN WORKING ON EQUIPMENT WHICHCONTAINS ELECTRICAL ENERGY
• Create an Electrically safe work condition
If that is not possible
• Train employees about the hazards• Plan the work in a way that minimizes risk• Protect the employee with the appropriate PPE
ESTABLISHING AN ELECTRICALLY SAFE CONDITION
Six Steps1) Planning, review up to date electrical diagrams and locate
all sources of electrical energy to the specific equipment and their isolation means.
2) Open the disconnect for each source3) Visually Verify that all phases are open4) Apply lock and tag according to written policies5) Test6) Ground
ESTABLISHING AN ELECTRICALLY SAFE CONDITION
In the process of creating an electrically safe work condition the worker is exposed to hazards and must be qualified, trained, wearing the appropriate PPE.
There is always some risk.Minimize the risk by making sure there is NO‐LOAD on the switchStand away from the doorWear the appropriate PPE (Table 130.7)
Are You Wearing your PPE?
Verify that all Phases are Open
Written Policy Specific to your Facility and each piece of equipment.
Lock Out Tag Out
Complexity Varies with the Device and the Facility
Lock Out Tag Out Policies
MEDIUM VOLTAGE TESTING
LOW VOLTAGE TESTING
Date Author Title INTERNAL 21
The load side of the circuit is grounded so that accidental closure will not energize the
equipment we are working on.
GROUNDING
Date Author TitleINTERNAL
23
IN MY 24 YEARS OF WORKING IN THE SCRAP INDUSTRY – NFPA 70E HAS ONLY
BECOME A PRACTICE SINCE 2005.
Capital City Metals in 2003SIMS Metal Management in 2009
Subcontractors you hire to create an Electrically Safe Work Condition for Metso – need to follow these Rules
Right now that is happening less than 50% of the time.
Date Author TitleINTERNAL
24
Six Steps1) Planning, 2) Isolate Source3) Visually Verify 4) LOTO5) Test6) Ground
When Metso Mueller Arrives to Maintain and Inspect Your Drive System We Complete
the following JSAMETSO-MUELLER - JSA WORKSHEET
Job Safety Analysis
A hazard is the potential for harm. In practical terms, a hazard often is associated with a condition or activity that, if left uncontrolled, can result in an injury or illness.
Completed by:
Date:
You are called to site XXX to:
(perform what task)
In order to do this work, the following individual tasks must be performed:
1Enter the work area
2Survey work area
3LOTO Motor
4LOTO Liquid Rheostat
5LOTO Switchgear & Capacitors
6LOTO Controls
7
8
9
# Exit the work area
Taking each task listed above, think about what general hazards (listed to right) you may be exposed to while performing that task. List the hazards you may be exposed to next to the task.
Possible Hazards Associated with Task a Impact with falling or flying objects
b Pentration of sharp objects
1Enter the work area a,b,c,d c Slips, trips or falls
2Survey work area L d Caught in or between a stationary/moving object
3LOTO Motor j e Fall from an elevated work platform, ladder or stairs
4LOTO Liquid Rheostat j
f Excessive lifting, twisting, pushing, pulling, reaching or bending
5LOTO Switchgear & Capacitors j
g Exposure to vibrating tools or equipment
6LOTO Controls j h Exposure to excessive noise
7 0 i Exposure to excessive heat or cold
8 0 j Electrical hazards
9 0 k Explosion hazard
# Exit the work area L other: ____________________________
Procedures for Creating Electrically Safe Condition
1Enter the work area a,b,c,d a Ensure that a hard hat and safety glasses are worn
b Ensure that steel toed boots are worn.
c Do not walk on or across metal or oily areas - clean up or take alternative route.
dEnsure that manager has made workers in the area aware of your presence, when working around moving equipment, maintain eye contact with operator.
2Survey work area L L Hazards unknown inspect work area
Bring any hazards found to the immediate attention of the site supervisor.
3LOTO Motor j jReview Diagrams and determine if they are up to date. Locate isolation means. Have customer/electrician open the isolations means. Visually verify all phases are open. Test for voltage. Ground the load side.
4LOTO Liquid Rheostat j jReview Diagrams and locate all sources of energy, typically 480VAC for pump/servo as well as 120VAC. De-energize and test.
5LOTO Switchgear & Capacitors j j Review Diagrams. Should have been made electrically safe when motor was LOTO. Verify that all energy sources were de-energized. Outside control power sources may exist. Identify the circuits and de-energize. Test to verify.
6LOTO Controls j j Review diagrams. Locate control power sources. De-energize for maintenance. If it is necessary to energize the controls for testing, wear appropriate PPE and plan work to minimize risk.
7 0 0
8 0 0
9 0 0
10Exit the work area 0
Date Author TitleINTERNAL
27
Date Author TitleINTERNAL
28
PPE’S
Date Author TitleINTERNAL
29
PPE’S
Date Author TitleINTERNAL
30
Date Author TitleINTERNAL
31
Date Author TitleINTERNAL
32
Date Author TitleINTERNAL
33
Date Author TitleINTERNAL
34
Date Author TitleINTERNAL
35
Date Author TitleINTERNAL
36
Date Author TitleINTERNAL
37
Date Author TitleINTERNAL
38
DESIGNING FOR SAFETY
Provide Arc Rated Switchgear and Distribution PanelsWindows for Verifying switch positionMCC’sExternal programming and testing pointsUse 24VDC control power