Electrical Billing and Rates Presentation

Electrical Billing and RatesMAE406 Energy Conservation in IndustryStephen Terry

Where Does Electricity for Industrial Plants Come From?Most from Investor Owned Utilities (IOUs) like CP&L and Duke PowerElectricities and NC Co-ops in small towns and rural locationsMay be generated on-site in Combined Heat and Power CHP) applications

How is Electricity Generated?Nuclear plants are baseloaded since they are cheap to operate and need long hours to pay back initial investmentCoal / Oil / Gas Boilers moderate costNatural Gas Turbines expensive to operate, used only for peak use

Power vs. EnergyPower is a rate quantity - 1 kW = 1 kJ/secEnergy is measured using kJ or kWh

Note: 1 kWh = 1 kJ-hr/sec = 3,600 kJ

Energy =

Parts of an Electric BillService Charge: Constant regardless of electrical energy use. Typically between $5 and $500 per monthEnergy Charge: charge based on amount of energy (kWh) usedDemand Charge: charge based on highest power required during intervalTaxes, Rebates, and Other Charges

Residential BillSmall service charge: for CP&L = $6.75Energy Charge: about $0.095/kWh for energy used in the summer and $0.085/kWh for winter.Demand Charge: does not apply since household is small userTaxes, Rebates: varies with user

Commercial / Industrial BillingIndustrial plants can use 1,000 kW or more of power. Power company must build capacity to meet the maximum load, even if it is used only a few hours per day air conditioners in the summer. Peak loads occur infrequently and must be met with expensive generation equipment (i.e., gas turbines), which increases cost to generate power.

Demand Intervals

Chart1

300

300

250

275

300

400

600

800

950

975

950

975

975

950

1000

1000

950

800

700

600

400

400

300

300

hour of day

Power, kW

Sheet1

12:00 AM300

1:00 AM300

2:00 AM250

3:00 AM275

4:00 AM300

5:00 AM400

6:00 AM600

7:00 AM800

8:00 AM950

9:00 AM975

10:00 AM950

11:00 AM975

12:00 PM975

1:00 PM950

2:00 PM1000

3:00 PM1000

4:00 PM950

5:00 PM800

6:00 PM700

7:00 PM600

8:00 PM400

9:00 PM400

10:00 PM300

11:00 PM300

Sheet1

hour of day

Power, kW

Sheet2

Sheet3

Billing DemandThe demand interval is usually 15, 30, or 60 minutes (see rate schedule).The maximum value of the power for all intervals in a month is the peak demand.Billing demand = peak demand, unless it is well below historical peaks or contract demand.

Demand Ratchet ClauseSome older rate schedules specify that the billing demand is the maximum actual demand for the last 12 months.It can also be either the current months peak demand or 80% of the contract demand.This is so power companies can recoup investment in power generators.

Industrial Electric Bill Based on rates from CP&L Large General Service 97 rate for a typical industrial plant energy and demand usage.

Time of Use RatesIts more expensive to make power during the day when everyone wants it rather than at night.Time of Use rate rewards customer using power at night with lower rates at night. However, rates during the day (on-peak) and the peak demand rate is usually higher.

Time of Use Rate Example

Chart2

300

300

250

275

300

400

600

800

950

975

0.4166666667950

0.4583333333975

0.5975

0.5416666667950

0.58333333331000

0.6251000

0.6666666667950

0.7083333333800

0.75700

0.7916666667600

0.8333333333400

0.875400

300

300

hour of day

Power, kW

Sheet1

12:00 AM300

1:00 AM300

2:00 AM250

3:00 AM275

4:00 AM300

5:00 AM400

6:00 AM600

7:00 AM800

8:00 AM950

9:00 AM975

10:00 AM950

11:00 AM975

12:00 PM975

1:00 PM950

2:00 PM1000

3:00 PM1000

4:00 PM950

5:00 PM800

6:00 PM700

7:00 PM600

8:00 PM400

9:00 PM400

10:00 PM300

11:00 PM300

Sheet1

hour of day

Power, kW

Sheet2

Off-peak hours

On-peak hours

Sheet3

TOU Example contdEnergy used in the blue shading is charged at on-peak rates ($0.03048/kWh for CP&L Rate 97)Energy used in the red shading is charged at off-peak rates ($0.02548/kWh)On-peak times are for non-holiday weekdays. Weekends / holidays are off-peakBilling demand is determined to be maximum power used during any on-peak interval

Sample Bill TOU Rate

Notes:TOU bill is more in this case. What is usage factor (is this a 1, 2, or 3 shift plant?)

Usage Factor=kWh / kW demand=350,000 kWh/ 1,000 kW=350 hrs/month=16 hrs/dayPlant probably operates two full shifts, maybe three shifts with lower production at night.

Notes:Time of use benefits companies that work seven days per week and manufacture at night.Costs can be reduced by scheduling operations around peak periods load shifting.Costs can be reduced by utilizing thermal storage for HVAC system and operating equipment during off-peak periods.

Other Types of RatesTiered Rate:Example: Energy Charge First 10,000 kWh-$0.05/kWhNext 25,000 kWh-$0.04/kWhAbove 35,000 kWh-$0.03/kWhPlant using 100,000 kWh would have an energy charge of $3,450 or $0.0345/kWh

Duke Rate IDouble tiered schedule based on ratio of kWh/kW demand, then sub-tiered based on energy usage within kWh/kW tier.These rates are difficult to compute, but generally reward companies that operate more hours and have flatter power profiles.

Average Energy ChargeMany plants will use an average energy rate in evaluating projects, which includes energy and demand costs.This is not accurate since equipment affected may not operate all of the time.

Average ErrorsExample 1: Turn lights off at night. For a time of use rate, what is proper energy charge if lights are turned off at 11 pm and back on at 6 am? How about demand?Example 2: Adding a new air conditioner to handle peak cooling. When does unit operate and what is energy cost? How about demand?

Power FactorSome utilities will charge for power factor.Power factor is the phenomenon of peak current draw being out of phase with peak voltage draw. This causes the power company to have to supply more power than is registered on the meter.Major causes electric motors that draw current for magnetizing the windings (inductive loads)

Power FactorSolution: install capacitors to offset inductive loadsCheck to see if youre charged for power factor first, most NC companies arent!

Other ChargesFuel Riders let power company adjust for highly varying prices for their fuelFacilities Charges extra equipment installed on-site, like a larger transformer or power fed from two separate lines for redundancy.

DeregulationOver the past 15 years, some state have deregulated electrical power. This means that billing for the three basic components are separate and users may choose their own suppliers:GenerationTransmissionDistribution

DeregulationVirginia has partially deregulated its markets and will fully deregulate in 2010.NC has no plans to deregulate anytime soonExperience has shown that most people see an increase in costs with deregulation because companies must compete with high cost of electricity to places like California.

ConclusionsMost power companies bill energy and demand.It is important to know your rate, on-peak hours and all costs.Use proper energy and demand rates for computing energy costs and savings.