This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4.(1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 6.02 6.02
5 0.47 0.47
6** 10.22 10.52
7 0.45 0.45
8 0.68 0.68
19.66 19.96
16"(C) 16"23
77
Table No. 4
Table No. 3
0.18
0.11
0.03 0.03
0.11
0.18
0.08
0.12
0.08 0.08
0.08
0.12
1.80 1.85
3.51
1.06
1.80 1.85
3.46
1.0625.4mm WALLTITE® (1")
Wall Assembly Components
Outside Air Film
Metal Siding
20mm Air Cavity
Wall Assembly Component
Thermal Resistance (A)
Frame 16" OC
RSI Effective Insulated Cavity
9.5mm Plywood (3/8")
Framing Factor %
2x4 Framing & 76.2mm WALLTITE® (3")
12.7mm Gypsum Board (1/2")
Effective Thermal Resistance of Wall Assembly Total
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)
Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.06
5 0.09
6** 1.80
7 0.08
8 0.12
3.47 / 19.72 3.52 / 20.02
5.02 / 28.52 5.02 / 28.52
4.41 / 25.04 4.41 / 25.04
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Wood Frame Wall with OSB Sheathing, WALLTITE® Exterior& Cavity Insulation
Reference Wall Assembly No. 1.20
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.06
5 0.20
6** 1.80
7 0.08
8 0.12
3.58 / 20.33 3.63 / 20.62
5.13 / 29.13 5.13 / 29.13
4.41 / 25.04 4.41 / 25.04
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 0.70
5** 1.80
6 0.08
7 0.12
3.02 / 17.15 3.07 / 17.44
4.57 / 25.95 4.57 / 25.95
4.05 / 23.00 4.05 / 23.00
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 3000 3000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 5999 5999
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)
12.7mm Gypsum Board (1/2")
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
25.4mm EPS (1") 3.98
2x4 Framing & 76.2mm WALLTITE® (3") 10.22
Wood Frame Wall with EPS Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.40
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Effective Thermal Resistance of Wall Assembly Total 3.02 3.07
0.18 0.18
2x4 Framing & 76.2mm WALLTITE® (3") 1.80 1.85
12.7mm Gypsum Board (1/2") 0.08 0.08
Outside Air Film 0.03 0.03
25.4mm EPS (1") 0.70 0.70
Metal Siding 0.11 0.11
20mm Air Cavity
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Wood Frame Wall with EPS Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.40
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 0.80
5** 1.80
6 0.08
7 0.12
3.12 / 17.71 3.17 / 18.01
4.67 / 26.52 4.67 / 26.52
4.15 / 23.57 4.15 / 23.57
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)
20mm Air Cavity 1.02
25.4mm Neopor® (1") 4.54
2x4 Framing & 76.2mm WALLTITE® (3") 10.22
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
Wood Frame Wall with Nepor Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.50
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Effective Thermal Resistance of Wall Assembly Total 3.12 3.17
2x4 Framing & 76.2mm WALLTITE® (3") 1.80 1.85
12.7mm Gypsum Board (1/2") 0.08 0.08
20mm Air Cavity 0.18 0.18
25.4mm Neopor® (1") 0.80 0.80
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Wood Frame Wall with Neopor Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.50
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 0.88
5** 1.80
6 0.08
7 0.12
3.20 / 18.17 3.25 / 18.47
4.75 / 26.97 4.75 / 26.97
4.23 / 24.02 4.23 / 24.02
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
25.4mm XPS (1") 5.00
2x4 Framing & 76.2mm WALLTITE® (3") 10.22
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Wood Frame Wall with XPS Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.60
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 5.00 5.00
5** 10.22 10.52
6 0.45 0.45
7 0.68 0.68
18.17 18.47
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
25.4mm XPS (1") 0.88 0.88
2x4 Framing & 76.2mm WALLTITE® (3") 1.80 1.85
12.7mm Gypsum Board (1/2") 0.08 0.08
RSI Effective Insulated Cavity
12" (B) 12"
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.20 3.25
Wood Frame Wall with XPS Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.60
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.02
5** 1.80
6 0.08
7 0.12
3.34 / 18.96 3.39 / 19.26
4.89 / 27.77 4.89 / 27.77
4.37 / 24.82 4.37 / 24.82
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
25.4mm PIR (1") 5.79
2x4 Framing & 76.2mm WALLTITE® (3") 10.22
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Wood Frame Wall with PIR Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.70
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 5.79 5.79
5** 10.22 10.52
6 0.45 0.45
7 0.68 0.68
18.96 19.26
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
25.4mm PIR (1") 1.02 1.02
2x4 Framing & 76.2mm WALLTITE® (3") 1.80 1.85
12.7mm Gypsum Board (1/2") 0.08 0.08
RSI Effective Insulated Cavity
12" (B) 12"
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.34 3.39
Wood Frame Wall with PIR Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 1.70
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.08
6 1.83
7 0.00
8 0.08
9 0.12
4.07 / 23.14 4.13 / 23.45
5.74 / 32.61 5.74 / 32.61
5.14 / 29.19 5.14 / 29.19
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm Plywood (3/8") 0.47
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.80 0.80
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 9.31 9.31
5 0.47 0.47
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
23.14 23.45
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
38mm WALLTITE®1.5") 1.64 1.64
9.5mm Plywood (3/8") 0.08 0.08
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 4.07 4.13
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.08
6 1.83
7 0.00
8 0.08
9 0.12
4.34 / 24.67 4.40 / 24.98
6.01 / 34.14 6.01 / 34.14
5.41 / 30.72 5.41 / 30.72
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
44.5mm WALLTITE® (1.75") 10.85
9.5mm Plywood (3/8") 0.47
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.91 0.91
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 10.85 10.85
5 0.47 0.47
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
24.67 24.98
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
44.5mm WALLTITE® (1.75") 1.91 1.91
9.5mm Plywood (3/8") 0.08 0.08
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 4.34 4.40
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.09
6 1.83
7 0.00
8 0.08
9 0.12
4.08 / 23.19 4.14 / 23.51
5.75 / 32.67 5.75 / 32.67
5.14 / 29.19 5.14 / 29.19
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm OSB (3/8") 0.53
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.80 0.80
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 9.31 9.31
5 0.53 0.53
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
23.19 23.51
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
38mm WALLTITE®1.5") 1.64 1.64
9.5mm OSB (3/8") 0.09 0.09
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 4.08 4.14
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.09
6 1.83
7 0.00
8 0.08
9 0.12
4.35 / 24.73 4.41 / 25.04
6.02 / 34.20 6.02 / 34.20
5.41 / 30.72 5.41 / 30.72
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
44.5mm WALLTITE® (1.75") 10.85
9.5mm OSB (3/8") 0.53
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.91 0.91
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 10.85 10.85
5 0.53 0.53
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
24.73 25.04
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
44.5mm WALLTITE® (1.75") 1.91 1.91
9.5mm OSB (3/8") 0.09 0.09
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 4.35 4.41
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.37
5 0.20
6 1.83
7 0.00
8 0.08
9 0.12
3.92 / 22.27 3.98 / 22.58
5.59 / 31.74 5.59 / 31.74
4.87 / 27.65 4.87 / 27.65
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
32mm WALLTITE® (1.25") 7.78
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.66 0.66
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 7.78 7.78
5 1.14 1.14
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
22.27 22.58
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
32mm WALLTITE® (1.25") 1.37 1.37
12.7mm Fibreboard (1/2") 0.20 0.20
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.92 3.98
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.20
6 1.83
7 0.00
8 0.08
9 0.12
4.19 / 23.80 4.25 / 24.11
5.86 / 33.28 5.86 / 33.28
5.14 / 29.19 5.14 / 29.19
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.77 0.77
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 9.31 9.31
5 1.14 1.14
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
23.80 24.11
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
38mm WALLTITE®1.5") 1.64 1.64
12.7mm Fibreboard (1/2") 0.20 0.20
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assmebly Total 4.19 4.25
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.20
6 1.83
7 0.00
8 0.08
9 0.12
4.46 / 25.33 4.52 / 25.65
6.13 / 34.81 6.13 / 34.81
5.41 / 30.72 5.41 / 30.72
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
44.5mm WALLTITE® (1.75") 10.85
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.87 0.87
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 10.85 10.85
5 1.14 1.14
6 10.40 10.71
7 0.00 0.00
8 0.45 0.45
9 0.68 0.68
25.33 25.65
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
44.5mm WALLTITE® (1.75") 1.91 1.91
12.7mm Fibreboard (1/2") 0.20 0.20
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 4.46 4.52
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.06
5 1.83
6 0.00
7 0.08
8 0.12
3.41 / 19.37 3.47 / 19.68
5.08 / 28.85 5.08 / 28.85
4.56 / 25.89 4.56 / 25.89
Table No. 1
Table No. 2
20mm Air Cavity 1.02
38mm EPS (1.5") 6.02
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Wood Frame Wall with EPS Sheathing & ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.40
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 6.02 6.02
5 10.40 10.71
6 0.00 0.00
7 0.45 0.45
8 0.68 0.68
19.37 19.68
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
38mm EPS (1.5") 1.06 1.06
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.41 3.47
Wood Frame Wall with EPS Sheathing, & ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.40
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.22
5 1.83
6 0.00
7 0.08
8 0.12
3.57 / 20.28 3.63 / 20.59
5.24 / 29.76 5.24 / 29.76
4.72 / 26.80 4.72 / 26.80
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm Neopor® (1.5") 6.93
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Wood Frame Wall with Neopor Sheathing & ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.50
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®,WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 6.93 6.93
5 10.40 10.71
6 0.00 0.00
7 0.45 0.45
8 0.68 0.68
20.28 20.59
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
38mm Neopor® (1.5") 1.22 1.22
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.57 3.63
Wood Frame Wall with Neopor Sheathing,& ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.50
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.02
5 1.83
6 0.00
7 0.08
8 0.12
3.37 / 19.14 3.43 / 19.46
5.04 / 28.62 5.04 / 28.62
4.52 / 25.67 4.52 / 25.67
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
25.4mm PIR (1") 5.79
2x4 Framing & 89mm ENERTITE® (3.5") 10.40
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.57 0.57
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Wood Frame Wall with PIR Sheathing & ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.60
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.02 1.02
4 5.79 5.79
5 10.40 10.71
6 0.00 0.00
7 0.45 0.45
8 0.68 0.68
19.14 19.46
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
20mm Air Cavity 0.18 0.18
25.4mm PIR (1") 1.02 1.02
2x4 Framing & 89mm ENERTITE® (3.5") 1.83 1.89
Vapour Barrier - Polyethylene 0.00 0.00
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.37 3.43
Wood Frame Wall with PIR Sheathing, & ENERTITE® Cavity Insulation
Reference Wall Assembly No. 2.60
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.08
6 1.45
7 0.00
8 0.08
9 0.12
3.97 / 22.52 3.99 / 22.68
4.62 / 26.25 4.62 / 26.25
4.02 / 22.83 4.02 / 22.83
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
44.5mm WALLTITE® (1.75") 10.85
9.5mm Plywood (3/8") 0.47
2x4 Framing & R-12 Fibreglass Batt (3.5") 8.25
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.93 0.93
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.08
6 1.45
7 0.00
8 0.08
9 0.12
3.70 / 20.99 3.72 / 21.15
4.35 / 24.72 4.35 / 24.72
3.75 / 21.29 3.75 / 21.29
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm Plywood (3/8") 0.47
2x4 Framing & R-12 Fibreglass Batt (3.5") 8.25
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.82 0.82
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.09
6 1.45
7 0.00
8 0.08
9 0.12
3.71 / 21.05 3.73 / 21.21
4.36 / 24.78 4.36 / 24.78
3.75 / 21.29 3.75 / 21.29
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm OSB (3/8") 0.53
2x4 Framing & R-12 Fibreglass Batt (3.5") 8.25
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.82 0.82
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.37
5 0.20
6 1.45
7 0.00
8 0.08
9 0.12
3.54 / 20.12 3.57 / 20.28
4.20 / 23.85 4.20 / 23.85
3.48 / 19.76 3.48 / 19.76
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
32mm WALLTITE® (1.25") 7.78
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & R-12 Fibreglass Batt (3.5") 8.25
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.67 0.67
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.20
6 1.45
7 0.00
8 0.08
9 0.12
3.81 / 21.65 3.84 / 21.81
4.47 / 25.38 4.47 / 25.38
3.75 / 21.29 3.75 / 21.29
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & R-12 Fibreglass Batt (3.5") 8.25
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.78 0.78
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.37
5 0.08
6 1.57
7 0.00
8 0.08
9 0.12
3.55 / 20.13 3.58 / 20.33
4.44 / 25.23 4.44 / 25.23
3.84 / 21.81 3.84 / 21.81
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
32mm WALLTITE® (1.25") 7.78
9.5mm Plywood (3/8") 0.47
2x4 Framing & R-14 Fibreglass Batt (3.5") 8.93
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.61 0.61
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.08
6 1.57
7 0.00
8 0.08
9 0.12
3.82 / 21.67 3.85 / 21.87
4.71 / 26.76 4.71 / 26.76
4.11 / 23.34 4.11 / 23.34
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm Plywood (3/8") 0.47
2x4 Framing & R-14 Fibreglass Batt (3.5") 8.93
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.71 0.71
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.09
6 1.57
7 0.00
8 0.08
9 0.12
4.10 / 23.26 4.13 / 23.46
4.99 / 28.35 4.99 / 28.35
4.38 / 24.87 4.38 / 24.87
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
44.5mm WALLTITE® (1.75") 10.85
9.5mm OSB (3/8") 0.53
2x4 Framing & R-14 Fibreglass Batt (3.5") 8.93
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.81 0.81
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.09
6 1.57
7 0.00
8 0.08
9 0.12
3.83 / 21.72 3.86 / 21.92
4.72 / 26.82 4.72 / 26.82
4.11 / 23.34 4.11 / 23.34
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
38mm WALLTITE®1.5") 9.31
9.5mm OSB (3/8") 0.53
2x4 Framing & R-14 Fibreglass Batt (3.5") 8.93
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.71 0.71
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.06
5 0.20
6 1.57
7 0.00
8 0.08
9 0.12
3.35 / 19.04 3.39 / 19.24
4.25 / 24.13 4.25 / 24.13
3.53 / 20.05 3.53 / 20.05
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
20mm Air Cavity 1.02
25.4mm WALLTITE® (1") 6.02
12.7mm Fibreboard (1/2") 1.14
2x4 Framing & R-14 Fibreglass Batt (3.5") 8.93
Vapour Barrier - Polyethylene 0.00
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation 0.48 0.48
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.37
5 0.20
6 1.57
7 0.00
8 0.08
9 0.12
3.66 / 20.80 3.70 / 21.00
4.56 / 25.89 4.56 / 25.89
3.84 / 21.81 3.84 / 21.81
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.08
6 1.49
7 0.00
8 0.08
9 0.12
3.74 / 21.23 3.77 / 21.40
4.47 / 25.40 4.47 / 25.40
3.87 / 21.98 3.87 / 21.98
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.08
6 1.49
7 0.00
8 0.08
9 0.12
4.01 / 22.76 4.04 / 22.93
4.74 / 26.93 4.74 / 26.93
4.14 / 23.51 4.14 / 23.51
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.09
6 1.49
7 0.00
8 0.08
9 0.12
3.75 / 21.28 3.78 / 21.46
4.48 / 25.46 4.48 / 25.46
3.87 / 21.98 3.87 / 21.98
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.91
5 0.09
6 1.49
7 0.00
8 0.08
9 0.12
4.02 / 22.82 4.05 / 22.99
4.75 / 26.99 4.75 / 26.99
4.14 / 23.51 4.14 / 23.51
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.37
5 0.20
6 1.49
7 0.00
8 0.08
9 0.12
3.58 / 20.36 3.62 / 20.53
4.32 / 24.53 4.32 / 24.53
3.60 / 20.44 3.60 / 20.44
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.18
4 1.64
5 0.20
6 1.49
7 0.00
8 0.08
9 0.12
3.85 / 21.89 3.89 / 22.07
4.59 / 26.06 4.59 / 26.06
3.87 / 21.98 3.87 / 21.98
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 7000 7000
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.08
4** 2.68
5 0.08
6 0.12
3.10 / 17.61 3.17 / 18.01
5.04 / 28.64 5.04 / 28.64
4.62 / 26.24 4.62 / 26.24
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
2x6 Framing & 102mm WALLTITE® (4") 15.21
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
9.5mm Plywood (3/8") 0.47
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
Wood Frame Wall with Plywood Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.10
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Effective Thermal Resistance of Wall Assembly Total 3.10 3.17
2x6 Framing & 102mm WALLTITE® (4") 2.68 2.75
12.7mm Gypsum Board (1/2") 0.08 0.08
Outside Air Film 0.03 0.03
9.5mm Plywood (3/8") 0.08 0.08
Metal Siding 0.11 0.11
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Wood Frame Wall with Plywood Sheathing& WALTITE® Cavity Insulation
Reference Wall Assembly No. 6.10
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.09
4** 2.68
5 0.08
6 0.12
3.11 / 17.67 3.18 / 18.07
5.05 / 28.69 5.05 / 28.69
4.62 / 26.24 4.62 / 26.24
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)
9.5mm OSB (3/8") 0.53
2x6 Framing & 102mm WALLTITE® (4") 15.21
12.7mm Gypsum Board (1/2") 0.45
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
Wood Frame Wall with OSB Sheathing & WALTITE® Cavity Insulation
Reference Wall Assembly No. 6.20
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Effective Thermal Resistance of Wall Assembly Total 3.11 3.18
2x6 Framing & 102mm WALLTITE® (4") 2.68 2.75
12.7mm Gypsum Board (1/2") 0.08 0.08
9.5mm OSB (3/8") 0.09 0.09
Metal Siding 0.11 0.11
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Wood Frame Wall with OSB Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.20
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.20
4** 2.68
5 0.08
6 0.12
3.22 / 18.27 3.29 / 18.67
5.16 / 29.30 5.16 / 29.30
4.62 / 26.24 4.62 / 26.24
Table No. 1
Table No. 2
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 5999 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 7000 7000
Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)
12.7mm Fibreboard (1/2") 1.14
2x6 Framing & 102mm WALLTITE® (4") 15.21
12.7mm Gypsum Board (1/2") 0.45
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
Wood Frame Wall with Fibreboard Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.30
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
Effective Thermal Resistance of Wall Assembly Total 3.22 3.29
2x6 Framing & 102mm WALLTITE® (4") 2.68 2.75
12.7mm Gypsum Board (1/2") 0.08 0.08
Metal Siding 0.11 0.11
12.7mm Fibreboard (1/2") 0.20 0.20
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Wood Frame Wall with Fibreboard Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.30
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff
1 0.03
2* 0.11
3 0.20
4** 2.50
5 0.08
6 0.12
3.04 / 17.24 3.09 / 17.57
4.50 / 25.55 4.50 / 25.55
3.96 / 22.49 3.96 / 22.49
Table No. 1
Table No. 2
Wall Assembly Components Reff
Outside Air Film 0.17
Metal Siding 0.62
12.7mm Fibreboard (1/2") 1.14
2x6 Framing & 89mm WALLTITE® (3.5") 14.17
12.7mm Gypsum Board (1/2") 0.45
Inside Air Film 0.68
Wall Thermal Resistance / PerformanceStud Spacing
305mm (12 in) 406 mm (16 in)Effective Thermal Resistance of Entire Wall Assembly (RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Centre of Cavity ( RSI / R-Value)
Nominal Thermal Resistance of Wall Assembly - Thermal Insulation Only (RSI / R-Value)
Outboard/Inboard Ratio of Insulation N/A N/A
Maximum Allowable Heating Degree Days Without Heat Recovery (Celsius Degree Days) 3000 5999
Maximum Allowable Heating Degree Days With Heat Recovery (Celsius Degree Days) 5999 7000
Wood Frame Wall with Fibreboard Sheathing & WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.31
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.***Refer to 2010 NBC Section 9.36 for minimum thermal resistance requirements for wall assemblies.****Refer to 2010 NBC, Section 9.25.5 for information on Outboard/Inboard ratio of insulation. Effecitve RSI and R information in Table No.1 is derived from Table No. 4.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.
RSIeff Reff RSIeff Reff
1 0.17 0.17
2* 0.62 0.62
3 1.14 1.14
4** 14.17 14.50
5 0.45 0.45
6 0.68 0.68
17.24 17.57
16"(C) 16"23
77
Table No. 3
Table No. 4
Wall Assembly ComponentsFrame 12" OC Frame 16" OC
Outside Air Film 0.03 0.03
Metal Siding 0.11 0.11
12.7mm Fibreboard (1/2") 0.20 0.20
2x6 Framing & 89mm WALLTITE® (3.5") 2.50 2.55
12.7mm Gypsum Board (1/2") 0.08 0.08
Inside Air Film 0.12 0.12
Effective Thermal Resistance of Wall Assembly Total 3.04 3.09
Wood Frame Wall with Fibreboard Sheathing& WALLTITE® Cavity Insulation
Reference Wall Assembly No. 6.31
* Similar wall assemblies with exterior finishes of brick, stucco or wood siding will have a similar but higher effective thermal resistance. ** Thermal Resistance values of Neopor®, WALLTITE® & ENERTITE® have been provided by BASF Canada Inc. All other thermal resistance values are based on those in the 2010 NBC, Table A-9.36.2.4.D.Thermal Resistance Calculations are based on the method noted in the 2010 NBC, Section A-9.36.2.4. (1)Thermal Resistance Calculations and Presentation Sheets have been developed by exp Services Inc. on behalf of BASF Canada Inc. The data presented in this document is based on calculations provided by exp Services Inc., which we believe to be reliable. This document is provided for information purposes only and without any representation, warranty or condition, expressed or implied, regarding the accuracy or completeness of the data or calculations. Whether or not the data or calculations are used or relied upon is within the sole discretion and judgment of the user. BASF does not assume any responsibility or liability, and expressly disclaims all liability, for any claim, loss, damage, injury or expense resulting therefrom.