-
- 1 -- 1 -
Thank you for your usual cooperation and support.We also thank
you for your introduction of our automatic search system for
partsnumbers of Nissan Forklift called *EF-FAST.Service parts will
be required when the parts are needed to be replaced for
annualinspection and when vehicles are repaired.Jobs such as the
search for parts numbers, the order and purchase, the
inventorycontrol, or the sales management will occur at various
kinds of steps before the serviceparts are installed in
vehicles.The parts numbers are key to all of these jobs.The EF-Fast
eases you to search part numbers accurately and rapidly.The EF-Fast
applies to windows 95, 98, 2000 & XP. Please have Dos/V
ready.
The operation of the EF-FAST is definitely easy and simple.
Please make a great useof this EF-FAST for your efficient and
rational management of parts numbers.We would be much obliged if
you could cooperate on stepping up the service for
NissanForklift.
If you need any assistance, please do not be hesitant to consult
with your distributor.
Preface
*EF-FAST stands for Export Forklift Fast Search for Technical
Information.
C 2006 NISSAN MOTOR CO., LTD
All Rights Reserved. No part of this publication may
bereproduced in any form without the prior written permissionof the
publisher.
-
- 2 -
Setting up the environment for EF-FAST 6
EF-FAST Starting Up - Quitting 7Procedure for starting up
7Creating Short cuts 8Procedure for quitting 9
Model Table ( Contained in this EF-FAST ) 4
EF-FAST Basic Operation to Search for Parts 10
A. Basic knowledge
Explanation of Initial Screen for EF-FAST 101 Menu 102 Icon 103
Area for Inputting Model Information 104 Area for Inputting Model
Specification 105 Area for Showing Result after P/No Search or P/No
Selection 106 Area for Model Input and Selection 107 Model Select
button 10
Explanation of Icon 12
B. Search ( Standard Truck )
1.Procedure for Parts Numbers Search 132.Model Selection 13
1 Way of inputting model code and Vin code. (Chassis number) 142
Way of inputting model series and Vin code 153 Way of inputting
model series 17
3.Search Section Key Number, Translation, and Supersession (Set
Alternation) 191 Way of Search by illustration 192 Search for
Supersession (Set Alternation) 243 Way of Search by Upper 3-5
Digits of Part Number 284 Way of Search by Description 315
Searching the Parts for V02 & F04 (Matrix Type) 34
2
1
Contents
-
- 3 -
Search for Special Truck Parts (Specially equipped Vehicle)
43
Procedure for Parts Number Search 44
C. Other Ways of Operation
Operating Scroll bar 36Getting Help 37Finding Out Meanings of
Marks and Abbreviation 38Printing 39Example 1 for selection of
Model Specification (Engine Forklift) 40Example 2 for selection of
Model Specification (Engine Forklift) 41Example 3 for selection of
Model Specification (Battery Forklift) 42
3
Contents
-
- 4 -
1 Model Table ( Contained in this EF-FAST )
1 AL01 AL01 Series JUL,2004 JAPAN F-616 Matrix Type2 AL02 AL02
Series JUL,2004 JAPAN F-616 Matrix Type3 C01 C01 Series AUG,1991
JAPAN C-F2004 D01S D01S Series DEC,1999 EUROPE CF-410-S5 D02S D02S
Series DEC,1999 EUROPE CF-420-S6 F03 F03 Series APR,1989 MAR,2001
JAPAN C-F1607 F04 F04 Series APR,2001 JAPAN C-F470 Matrix Type8
F04E F04 Series AUG,2001 EUROPE C-F4809 F05 F05 Series APR,1983
JAPAN C-F090
10 H01 H01 Series APR,1986 JUN,1993 JAPAN C-F10011 H02 H02
Series APR,1986 JUN,1993 JAPAN C-F11012 H02S H02S Series JUL,1989
SEP,1993 EUROPE CF-F110-S13 J01 J01 Series JUN,1993 SEP,2003 JAPAN
C-F22014 J01S J01S Series SEP,1995 DEC,1999 EUROPE CF-220S15 J02
J02 Series JUN,1993 SEP,2003 JAPAN C-F23016 J02S J02S Series
SEP,1993 DEC,1999 EUROPE CF-240S17 L01 L01 Series SEP,2003 JAPAN
C-F50018 L02 L02 Series SEP,2003 JAPAN C-F51019 M01 M01 Series
JAN,1988 DEC,1996 JAPAN C-F13020 M02 M02 Series JAN,1988 SEP,1997
JAPAN C-F14021 N01 N01 Series MAY,1992 SEP, 2005 EUROPE C-F210-SU22
P01 P01 Series DEC,1995 FEB, 2006 JAPAN C-F33023 P02 P02 Series
DEC,1995 FEB, 2006 JAPAN C-F34024 U01 U01 Series MAR,2005 JAPAN
C-F600 Matrix Type25 U02 U02 Series MAR,2005 JAPAN C-F600 Matrix
Type26 Q02 Q02 Series JUL,1997 EUROPE CF-250-S27 V02 V02 Series
APR,1996 JAPAN C-F341 Matrix Type28 INIS INIS Series SEP,2005
EUROPE C-F610-S29 1B1 1B1 Series FEB,2006 JAPAN C-F620 Matrix
Type30 1B1C 1B1C Series MAR,2006 JAPAN C-F640 Matrix Type31 1B2 1B2
Series FEB,2006 JAPAN C-F630 Matrix Type32 1B2C 1B2C Series
MAR,2006 JAPAN C-F650 Matrix Type
1. The part catalog contains the following 28 models of Nissan
Forklift Truck.2. The information of Special Trucks is available in
the catalog as well.Special Trucks are identified
by the three digits of **Z ,ex. 86Z ,on the top of Model
Codes,which are indicated on ModelNumber Plates.Be sure to check
with a Model Code before investigating special trucks with
thiscatalog. Please access to the section of Search for Special
Truck for the Specially equippedVehicle.
Applied Date Prodct CatalogRemarksNo Spcode Spname From Up To
Plant Pub.No.
-
- 5 -
- MEMO -
-
- 6 -
Start
to run.
Program Forklift PartsCatalog Setting1
2
Make sure CD-ROM drive.CD-ROM drive of your computer should be
listed.If not,correction will be required.
OK to finish
Make sure your Language.
Setting up the environment for F-FAST
-
- 7 -
AB C
EF-FAST Starting Up - Quitting
Procedure for Starting Up
(3) Click the start button at the lower left on the screen by
left mouse button.The Menu like A shown below will appear. (4)
Point to Program (P) so that the menu like B will appear. (5) Point
to Euro Forklift Parts Catalog so that the menu like C will appear.
(6) Finally, point to Euro Forklift Parts Catalog and click by left
mouse button. Then, the program starts up, and the initial screen
of EF-FAST appears.
(1) Turn your computer on. (2) The screen shown below will
appear.
You can also start up from the short cut
icon, if you have created it.
(Double click the short cut icon )
-
- 8 -
Creating Short cuts(1) Turn your computer on.(2) The screen
shown to the right will appear.(3) Left click the Start button on
the lower
left of the screen. The below A menuwill be displayed.
(4) While continuing to hold down theclicking button, move the
arrow of themouse to PROGRAM. The B menu willthen be displayed.
(5) While continuing to hold down the clicking button, move the
mouse toEuro Forklift Parts Catalog. The C menu will then be
displayed.
(6) Place the arrow of the mouse on Euro Forklift Parts
Catalog.Right click the mouse after it has highlighted the section
black. The D menu will then bedisplayed.
(7) Select Copy from The D menu.
(8) Next, place the arrow of the mouse on any area of the
desktop anddisplay the E menu by right clicking. Then click Paste
Shortcut.
(9) The SHORT CUT F will be created.
A B C
D
E
F
-
- 9 -
Initial Screen of EF-FAST
Procedure for QuittingIt can be quitted in any ways numbered 1
through 3 .
4
23
1
After 1 Model code and 2 Vin code (Chassis No) are input, click
3 Model select (OK)button. By doing this command, EF-FAST
runs.After model series is input (or click 4 Model Series
button-select), EF-FAST can also run byclicking 3 Model select ( OK
) button.
1
3
1 Click File and Exit button on the sub-menu.2 Click X .3 Click
the icon.
Operation
2
Click the button after oneof any ways numbered1 through 3
wascompleted.
-
- 10 -
A. Basic Knowledge
Explanation of Initial Screen for EF-FASTIt is ready to search
upon starting up the screen shown below.
2 EF-FAST Basic Operation to Search for Parts
2 Icon
3 Area for Inputting Model Information
4 Area for Inputting Model Specification
5 Area for Showing Result after P/No Search or P/No
Selection
When you want to change the sizeof a screen, move the mouse
pointerto the lower right corner until itchanges to .Then,hold down
the mouse buttonand move.
1 Menu
7 Model Select Button
6 Area for Model Input and Selection
1 Menu after Model Selection
-
- 11 -
1 MenuClicking the menu button opens sub-menu.In case of
operating by keyboard hold down the ALT key and press alphabetical
keyindicated on the right side of the menu.
File Clear (F12)Print (F6)Quit(EXIT)
Illustration Illustration (F2)Illust index (F2)Zoom (Z)Standard
(T)
Search Search by Description (F7)TOOL P/N Search (F5)
Windows Previous Screen (F4)Previous Section (F11)Next Section
(F12)
Help IndexVersion information
(ex.) The part in case of opening ToolP/N Search (F5) on the
menu bar.
2 Icon (Small pictures lining up on the upper part)Clicking icon
starts each function. For more detail, please refer to the next
page.
3 Area for inputting model series informationArea for inputting
model Vin-code, model series and so on.
4 Area for inputting model SpecificationArea for inputting
narrowing down detailed specifications upon knowing the model.
5 Area for showing result after P/No search or P/No
selection.Key No., parts numbers, and result of P/N search which
are input in the input area areindicated.You cannot input in this
area.
6 Area for model input and selection
7 Model select buttonOnce model and Vin code are input, click
here.
-
- 12 -
Explanation of Icon (Small pictures lining up on the upper
part)
Clicking icon by left mouse button starts each function.
Illustration Screen
Illustration Index Screen
Function Icon
Quit (Exit)
Back
Print
Continuos Illustration
Help
Initial Screen & Showing Result screen
Function Icon
Quit (Exit)
Clear
Print
Group Index
Search by Description
Search Part Number
Abbreviations
Help
Parts No. Selection Screen
Function Icon
Search Specification
Search Supersession
Function Icon
Quit (Exit)
Group Index
Print
Search Part Number
Zoom (Illustration)
Previous Section
Previous Illustration
Next Illustration
Next Section
Section Scroll
Help
-
- 13 -
B. Search (Standard Truck)
1. Procedure for Parts Number Search
Model SelectionThe following three methods are available.
1 Input model code and Vin code.(Chassis number)2 Input model
series and Vin code.3 Input model series.
Parts Numbers Search and TranslationThe following three methods
are available.
1 Search by Illustration.2 Search by Upper 3-5 Digits of Part
Number.3 Search by Description.
Search for Supersession (Set Alternation)
2. Model Selection
Special Truck has ** Z at the first three digits of model code
on theModel No Plate. On this truck please refer to Search for
SpecialTruck.
Note
The following three methods are available.1 Inputting model code
and Vin code.(Chassis number)2 Inputting model series and Vin
code.3 Inputting model series.Note : Model code and Vin code are
stamped on mode No.plate.
-
- 14 -
1 Way of inputting model code and Vin code. (Chassis number)
Input model code and Vincode here, and then pressenter or click
OK button.
Basic Flow
When the model code is input, the mast and height can only be
input if you click the MAST and the HEIGHT button. Other Model
specification (element) appearsautomatically.
ex. Model YGJ02A30U-111510 selection.
-
- 15 -
The following screen is another example.
Note If model code exists in both Murayama and NFESA plant, this
messageappears. Please select one you need.
ex. Model UJ02A20U selection.
2 Select the model series you wish to search.(Click mouse
button)3 Click OK button after the selection.
2 Way of inputting model series and Vin code. Click the
ModelSeries button.
1
Input the Vin code (chassis No).(You can accurately search to
theapplied year and month on thepart catalog with
informationobtained from the Vin code.)
4
-
- 16 -
ex. Vin code YGJ02-111510 selection.
Input the Model Specification after each of the button was
pressed.
ex. Model series J02 selection.
-
- 17 -
3 Way of inputting model series.
4 Click OK button after model series is determined.
Click the Model Series button.1
2 Select the model series you wish to search.(Click mouse
button)
3 Click OK button after the selection.
-
- 18 -
5 Input the model specification after the each of the button was
pressed.
Please refer to EX. 1-3 for selection of Modelspecification (See
Page 40-42)
-
- 19 -
Click here after ( ) is marked.Clicking cancelgoes to
previousscreen.
3. Search Section Key Number, Translation, and Supersession (Set
Alternation)
The following three methods are available.1 Search by
illustration.2 Search by Upper 3-5 digits of part number.3 Search
by description.
1 Way of Search by illustration.1 Click Group Index icon to have
screen below.2 Check any required item (Click mouse button) to
select the group of Illust. Group Index.3 After the selection is
completed, click OK button.
Group Index
You can select multiple Group Index.
Click the check box to select (click )
Press Enter key after inputting3 digits here if you knowSec No.
By doing this, youhave desired illustration directly.
-
- 20 -
4 Click the required part section so that Group Index will
appear and the color of screenchanges to red for selection.You can
select multiple sections.(Example of Search is F03)
5 After the selectionis completed,ClickOK button.
Illustration will be shown.(illustration below)
6 Click the required Section No. by mouse button so that the
color of SEC No. changes tored or green for selection. You can
select multiple parts SEC No.
Click here to Previous section Click here to Next section
To see next page, click here
Click here to Zoom
First click the Key No ofarea you want to zoom.
ex. Engine group
ex. Sec : 100 (Engine)
-
- 21 -
By Zoom iconThe part will be shown clearly if it is zoomed.
Click the same button again to return the size asit was.
Indication of P/N Search
7 After you click the Key No. of the part you need, click icon
of P/N Search. (Translation)
8 P/N Search starts.
ex. SEC : 200A EXHAUST TUBE MUFFLER
ex. SEC : 200A EXHAUST TUBE MUFFLER
The Key No. selected have adifferent colors of red or green.
-
- 22 -
9 The detail of each partwill be indicated by theorder you
selected.
Click OK button afterthe selection by amouse button.
The screen goes on tothe next page (the nextparts).
Select by mouse.***** will appear in the selectcolumn.
Select parts. Click OK button.
-
- 23 -
10 The parts number will appear if selected all.Ex.Showing
Result after Part Number Selection.
That is all for a easy way to search parts.
Click here.Part specification screen appears.
Click here.Search for supersession screen appears.Example is
shown next page.
-
- 24 -
2 Search for Supersession (Set Alternation)
Ex.J01 Sec.200C
Case 2
Case 1
Screen of result after P/No. Selection
Click here(Case1 2 appears)
Click here to quit
-
- 25 -
[ Case-1 ] Not Alternation PartsP/No 20040-40K03 search
-
- 26 -
[ Case-2 ] Set Alternation Parts Search
1 If ICA code 5-9 appeared you can serch set sub situation
parts. 2 Click set Alternation button. 3 Set Alternation Parts will
appears. (See next page)
2
to run.
1 Start Program Forklift PartsCatalog Euro ALTENATE PART NO.
P/No 20040-40K01 search
Click here
-
- 27 -
Explanation of ICA Code
Interchangeable codeCodes are assigned to each alternate part in
a supersession chain. The codes are :
2,3,4 Can be used unconditionally.
5 Can be used with some other parts.
6,7,8 Can be used under certain conditions
(Different color, size, etc., but no functional differences are
allowed).
9 Can be used on certain models.
0 Can not be used (not interchangeable).
ex.Set AlternationICA code Set Alternation Parts3
-
- 28 -
[ Operation 1 ] 1) After inputting Model information and Model
specification, click the OK button.Then, click the Add button.Input
part number.
[ Operation 2 ] 2) Press the Enter key or click the Add
button.3) The upper 5 digits of the part number selection screen
opens,and then the
upper 5 digits of the part number, description, and Sec No.
appear.4) Left-click the check box to select. Right-click to
cancel.5) After selecting all the options, click the display
illustration button to open the
illustration screen.6) The parts selected in step 4 are
automatically set with the quantity of " 1. " If
you do not need the part,or want to increase the quantity, use
the left/rightbuttons of the mouse to change the quantity.
3 Way of Search by Upper 3-5 Digits of Part Number
Area for input 3 to 5 digits. Click Add button.Input P/No
A
B
D
C
AB
-
- 29 -
C The upper 3-5 digits of the part number selection screen. ex.
P/No 58211 ( CYLINDER ASSY - LIFT. MAST )
Click here to select
Click here so thatillustration screenappears. (Shown below)
D Illustration screen ex. 580SEC (CYL ASSY - LIFT)
P/N Search starts.
Click here P/Nosearch start
If you use the Menu bar, click the Tool and press the
search.
-
- 30 -
[ Operation 3 ] 8) In case there are two or more parts numbers,
the screen of Selecting Parts willappear. Click the required parts
and button. (or press Enter key.)
Showing result of selected Parts.
ex. After P/No search ( 58211-01H02 )
Click the button
Click the button
-
- 31 -
[ Operation 2 ] Input the first letter of the description and
click the OK button.( Also, you can input all of the description.
)
Click here
4 Way of Search by Description
[ Operation 1 ] Click the icon of Search by Description ( )
.
Adopt one of these two ways
(Parts No.5 digit screen will appears.)
-
- 32 -
ex. Parts No.5 digit screen.
ex. Illustration screen.
1
2
[ Operation 3 ] 1 Click the check box to select. Right click to
cancel. 2 Click the display Illustration button.
[ Operation 4 ] Illustration screen like below will appear.Click
the P/No search button on the illustration screen.P/No select
screen appears. (See next page)
-
- 33 -
ex. P/No select screen.
Click here to select. If it is selected, ***** ***** ***** *****
***** will appear.The Result of P/No search screen will appear.
(Shown below)ex. The Result of P/No search.
[ Operation 5 ] P/No Select screen like below will appear.Click
the required P/No. and click OK button on the P/No select
screen.
Right-Click the part marked * on the screen andset when you want
to refer to illustration or take alook at parts description after
the P/N search.
*
*
-
- 34 -
5 Searching the Parts for V02 & F04 (MATRIX TYPE)
Click the Model select as it is impossible to select if two or
more parts are shown.
See 'Remarks' field of Model Table (Page 4) for confirming
MATRIX TYPE model.The procedures before this are the same as those
mentioned before. It searches for the KeyNo. clicked.
-
- 35 -
Click the OK button after the selection was made in the Model
select screen. The procedures afterthis are the same as the search
for mentioned before.
The Applied Position No.in the Model select screen is the same
as the number in the Applied Modelcolumn of a book-type
catalogue.
-
- 36 -
See below
Operating Scroll BarThe scroll bar will appear on the right or
the lower part of the screen in the case that all ofinformation are
not on the current screen.In this case,drag (*1) the scroll box or
click the scroll allow.
Clicking left or right scroll allow scrolls the screen at a
regular interval.
Drag the box.
Drag Moving Mouse with holding down the mouse button.
Printing the current print settings.
Scroll Bar Click each line marked * and adjust thenumber to a
required number by clickingbutton in the Number of column.
Starting all over again.(Clear screen)
C. Other Ways of Operation
Indicating explanation ofmarks and abbreviations.
Click here to decrease
Order quantity input area
Click here to increase
Indicating explanation of help.
-
- 37 -
Getting Help
Find out the way of operation with the Help function if you have
a problem in operation.
[ Operation 1 ] Click icon of the Help( or choose Help Contents
in Menu Bar.)
In either case,you can get information.
[ Operation 2 ] Within the contents, click the item which you
wish to see help.
-
- 38 -
Finding Out Meanings of Marks and Abbreviations
[ Operation 1 ] Click the icon of Explanation for Marks( ) or
choose Tool - Marks andAbbreviation.
In case of selecting with Icon,
In case of selecting with Menu,
(ex.) Explanation of Marks and Abbreviations for J02.
Clicking the desired item forexplanation changes
information.
Choose
-
- 39 -
Printing
The screen with the icon of Print is ready to print.
[ Operation 1 ] Clicking the icon of Print shows the screen for
printer setup.
Setup your printer by following procedures of your own PC.
-
- 40 -
Example 1 for Selection of Model Specification (Engine
Forklift)
Mast Type
MAX.Fork Height
Wheel Base
ex. J02
After the model information was determined in accordance with
the steps mentioned before, pleasefollow the direction below.
1) The list of elements for each item appears on the screen.
Select the item with the mouse or up /down arrow keys on the
keyboard. Click the OK button.
2) When the model code is input, only the mast and height can be
input. Other elements appearautomatically.
ex. J02
ex. J02
Title button
Elements
-
- 41 -
Example 2 for Selection of Model Specification (Engine
Forklift)
Engine Model
Transmission Type
Load Capacity
ex. J02
ex. J02
ex. J02
-
- 42 -
Example 3 for Selection of Model Specification (Battery
Forklift)
Traction Motor
Body Size
Seat Style
ex. C01
ex. C01
ex. C01
-
- 43 -
(Notes). Contained parts mentioned can only be searched..
Special Truck have **Z at the first three digits of model code on
the Model No.Plate.. Special parts can not be search by
illustration.
3 Search for Special Truck Parts (Specially equipped
Vehicle)
MADE IN JMADE IN JAPAN
NISSAN MOTOR CO., LTD.
4470
86ZFJ02A2SUFJ02-1179303F385 SINGLEROLL CLAMP-YAMAKAWA
MODEL VARIATIONCHASSIS NO.
M A S TATTACHMENT
TRUSK WEIGHT
TIRE
KG
CAPACITY WITH MAST VERTICAL
ECCENTRICITY
MAX LIFT HEIGHT 3850 mmMAX. ROLL DIAMETER 1300 mm
1550 KG
mm
Model No.Plate
Special Trucks have **Z.
-
- 44 -
4 Click the special Truck button.Specially equipped Block List
will appear.
Procedure for Parts Numbers Search
You can learn the procedure through the example of searching
specially equipped vehiclesin the actual record of Special Truck
(86ZFJ02A25U-117930).
[Operation 1 ] Click the OK button (or Enter key) after Model
code and Vin code. are input on theinitial screen.
(It is OK to input only Model code in the case which production
date is not required.)
1 Input Model code (Model listed on the Model No. Plate) + Enter
key
2 Input Vin codeafter the movement of cursor.
Input FJ02 Input 117930
3 Click the OK button or Press Enter key,then special truck
button is appears.
* If you see a message sayingInvalid Vin Code, Double-check on
input error for Model No. ( 1 2 above)
-
- 45 -
[ Operation 2 ] As shown below, The list will appear.Click the
required block and then click the OK button.(The block of 21D19
BETUOKI OIL COOLER is selected in this ex.)***** will appear in the
column of Select upon selected.
[ Operation 3 ] Parts No. for special Truck will appear.Click
the required parts block and then click the OK button.
Click the required parts and then click the OK button.
The Screen for special Parts Truck Information will appear like
below.
P/No Not Registered.P/No Registered.*
P/No Special Truck
-
- 46 -
Required part, Hose-oil cooler, has been selected.(the screen
shown below)