Eeng 360 1 Chapter 3: Pulse Code Modulation Pulse Code Modulation Quantizing Encoding Analogue to Digital Conversion Bandwidth of PCM Signals.

Eeng 360 1

Chapter 3: Pulse Code Modulation

Pulse Code Modulation Quantizing Encoding Analogue to Digital Conversion Bandwidth of PCM Signals

Huseyin BilgekulEeng360 Communication Systems I

Department of Electrical and Electronic Engineering Eastern Mediterranean University

Eeng 360 2

PULSE CODE MODULATION (PCM)PULSE CODE MODULATION (PCM)

DEFINITION: Pulse code modulation (PCM) is essentially analog-to-digital conversion of a special type where the information contained in the instantaneous samples of an analog signal is represented by digital words in a serial bit stream.

The advantages of PCM are: • Relatively inexpensive digital circuitry may be used extensively. • PCM signals derived from all types of analog sources may be merged with

data signals and transmitted over a common high-speed digital communication system.

• In long-distance digital telephone systems requiring repeaters, a clean PCM waveform can be regenerated at the output of each repeater, where the input consists of a noisy PCM waveform.

• The noise performance of a digital system can be superior to that of an analog system.

• The probability of error for the system output can be reduced even further by the use of appropriate coding techniques.

Eeng 360 3

Sampling, Quantizing, and Sampling, Quantizing, and EncodingEncoding

The PCM signal is generated by carrying out three basic operations: 1. Sampling

2. Quantizing

3. Encoding

1. Sampling operation generates a flat-top PAM signal.

2. Quantizing operation approximates the analog values by using a finite number of levels. This operation is considered in 3 steps

a) Uniform Quantizer

b) Quantization Error

c) Quantized PAM signal output

3. PCM signal is obtained from the quantized PAM signal by encoding each quantized sample value into a digital word.

Eeng 360 4

Analog to Digital ConversionAnalog to Digital Conversion The Analog-to-digital Converter (ADC)

performs three functions:

– Sampling• Makes the signal discrete in time. • If the analog input has a bandwidth

of W Hz, then the minimum sample frequency such that the signal can be reconstructed without distortion.

– Quantization• Makes the signal discrete in

amplitude.• Round off to one of q discrete levels.

– Encode• Maps the quantized values to digital

words that are bits long. If the (Nyquist) Sampling Theorem is

satisfied, then only quantization introduces distortion to the system.

ADC

Sample

Quantize

AnalogInputSignal

Encode

111110101100011010001000

Digital OutputSignal

111 111 001 010 011 111 011

Eeng 360 5

QuantizationQuantization

The output of a sampler is still continuous in amplitude.

– Each sample can take on any value e.g. 3.752, 0.001, etc.

– The number of possible values is infinite.

To transmit as a digital signal we must restrict the number of possible values.

Quantization is the process of “rounding off” a sample according to some rule.

– E.g. suppose we must round to the nearest tenth, then: 3.752 --> 3.8 0.001 --> 0

Eeng 360 6

Illustration of the Quantization Error

Eeng 360 7

PCM TV transmission:

(a) 5-bit resolution;

(a) 8-bit resolution.

Eeng 360 8

Uniform QuantizationUniform Quantization

• Most ADC’s use uniform quantizers.

• The quantization levels of a uniform quantizer are equally spaced apart.

• Uniform quantizers are optimal when the input distribution is uniform. When all values within the Dynamic Range of the quantizer are equally likely.

Input sample X

Example: Uniform =3 bit quantizer

q=8 and XQ = {1,3,5,7}

2 4 6 8

1

5

3

Output sampleXQ

-2-4-6-8

Dynamic Range:

(-8, 8)

7

-7

-3

-5

-1

Quantization Characteristic

Eeng 360 9

Quantization Example

Analogue signal

Sampling TIMING

Quantization levels. Quantized to 5-levels

Quantization levelsQuantized 10-levels

Eeng 360 10

PCM encoding example

Chart 1. Quantization and digitalization of a signal.

Signal is quantized in 11 time points & 8 quantization segments.

Chart 2. Process of restoring a signal.PCM encoded signal in binary form:

101 111 110 001 010 100 111 100 011 010 101Total of 33 bits were used to encode a signal

Table: Quantization levels with belonging code words

Levels are encoded using this table

M=8

Eeng 360 11

EncodingEncoding• The output of the quantizer is one of M possible signal levels.

– If we want to use a binary transmission system, then we need to map each quantized sample into an n bit binary word.

• Encoding is the process of representing each quantized sample by an bit code word.– The mapping is one-to-one so there is no distortion introduced by

encoding.

– Some mappings are better than others.

• A Gray code gives the best end-to-end performance.

• The weakness of Gray codes is poor performance when the sign bit (MSB) is received in error.

22 , log ( )nM n M

Eeng 360 12

Gray CodesGray Codes• With gray codes adjacent samples differ only in one bit position.

• Example (3 bit quantization):

XQ Natural coding Gray Coding +7 111 110

+5 110 111

+3 101 101

+1 100 100

-1 011 000

-3 010 001

-5 001 011

-7 000 010

• With this gray code, a single bit error will result in an amplitude error of only 2.

– Unless the MSB is in error.

Eeng 360 13

Waveforms in a PCM system for M=8Waveforms in a PCM system for M=8

M=8

(d) PCM Signal

(c) Error Signal

(b) Analog Signal, PAM Signal, Quantized PAM Signal

(a) Quantizer Input output characteristics

22 log ( )

is the number of Quantization levels

is the number of bits per sample

nM n M

M

n

Eeng 360 14

PCM Transmission SystemPCM Transmission System

Eeng 360 15

Practical PCM CircuitsPractical PCM Circuits• Three popular techniques are used to implement the

analog-to-digital converter (ADC) encoding operation:

1. The counting or ramp, ( Maxim ICL7126 ADC)2. Serial or successive approximation, (AD 570)3. Parallel or flash encoders. ( CA3318)

• The objective of these circuits is to generate the PCM word.

• Parallel digital output obtained (from one of the above techniques) needs to be serialized before sending over a 2-wire channel

• This is accomplished by parallel-to-serial converters [Serial Input-Output (SIO) chip]

• UART,USRT and USART are examples for SIO’s

Eeng 360 16

Bandwidth of PCM SignalsBandwidth of PCM Signals• The spectrum of the PCM signal is not directly related to the spectrum of the

input signal.• The bandwidth of (serial) binary PCM waveforms depends on the bit rate R and

the waveform pulse shape used to represent the data.• The Bit Rate R is

R=nfs

Where n is the number of bits in the PCM word (M=2n) and fs is the sampling rate.

• For no aliasing case (fs≥ 2B), the MINIMUM Bandwidth of PCM Bpcm(Min) is:

Bpcm(Min) = R/2 = nfs//2

The Minimum Bandwidth of nfs//2 is obtained only when sin(x)/x pulse is used to generate the PCM waveform.

• For PCM waveform generated by rectangular pulses, the First-null Bandwidth is:

Bpcm = R = nfs