This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
EDM “V” Pack Cooler Cooling for engine, Hydraulic, Compressor
Rotation Head Top Drive with Floating Spindle
Two speed, Low/High manual gear change. 5-150 rpm Low Gear; 150—1250 rpm High Gear Hollow Floating spindle ID: 114.3 mm – 5 ½” API IF pin thread High Gear Maximum displacement: 2964 lbft (4018 Nm) @564 rpm High Gear Minimum displacement: 1336 lbft (1811 Nm) @1252 rpm Low Gear Maximum displacement:12360 lbft (16758 Nm)@135rpm Low Minimum displacement: 5571 lbft (7553 Nm) @ 300 rpm
Mast
Heavy Duty two piece tubular section mast structure Capable of angles from vertical to 45° 2000mm ( 6.6 ft )mast dump Standard hydraulic mast raise cylinders with counter balance valves.
Head Traverse
Driven by one hydraulic cylinder, 2:1 rope system Traverse Up Speed 830 mm/sec ( 2.72 ft/s ) Traverse Down Speed 622 mm/sec ( 2.04 ft/s ) Side racking rotation head to L/H side 7.6m ( 25 ft )stroke with rotation head
Feed Capacity
Pull Down 22.500 lbf ( 10.205 kg ) Pull Back 95.000 lbf ( 43.091 kg )
Main Winch Mounted on top of mast (Type Braden HD80C) Max pull 245kN ( 55,000 lbf ) Max speed 55m/minute ( 246 ft/min ) Failsafe brake mechanism (spring applied, hydraulic release) 9 metre ( 30 ft ) pull for diamond pipe and casing Load sensing winch motor for optimum operating speed Winch limiter to prevent cable overrun
Jib Boom ( Optional )
Actuated by hydraulic cylinder for raise/lower Actuated by hydraulic hourglass worm for left/right Independent winch with lifting capacity of 200kg ( 440 lb )
Water Pump
FMC (Bean) L1118DSC 246 LPM@13800KPa 65 GPM @ 2000PSI Powered from rig hydraulic system
Rod Break Out
Hydraulic cylinder mounted EDM Rap spanner for N+, H+ and P+ casing Metzke Makorbreak Hydraulic breakout wrench. Adjustable height Air Drill rotating rod breaker up to 5,5” capacity
Rod Spinner
EDM Rod Spinner MP with N+ , H+, P+ PWT Capacity Adjustable torque control Breaking torque 2980 Nm ( 2,200lbft ) Hydraulic slew in/out of mast
Jack Legs Heavy duty cylinders with pilot check valves and flow fuses for safety Extra large pads for better ground stability
Rod Clamps & Slips Table Hydraulically opening front and rear slips table with 100mm (4") travel Maximum table opening of 508mm (20") Hydraulically operated RC Spanner Hydraulically operated, self energising rod clamp ( UDR Type ) Easy to remove jaws
Common jaws from 44.5mm to 139.7mm ( B+, N+, H+, P+, HW, PW)
EDM 95K SERIES DRILLS Track/Truck Mounted, Diamond/Multipurpose
Safety—Efficiency—Trust
www.explorationdrillmasters.com
Wireline Winch Mounted on mast pivot plate Capacity of 3000m ( 9850ft) of 8mm (5/16") wire rope Maximum average pull from full to empty drum 15950N (3590 Ibs) Maximum average speed from full to empty drum 9.1 m/sec (29.9 ft/s) Automatic rope spooler Wire line winch overrun limiter with wiper
Control Panel
Pivoting Control Cabinet off rear right corner of machine Good visibility at all mast angles Folding drillers jump up stand and protective roof Slews behind for transport Easy self explanatory layout Easy access for basic maintenance and repairs Fully sealed control panel with all electrical instrumentation.
Tilting Rod Bin
Capacity of 28 x 4-1/2” RC pipe
Additions for RC Drilling Capacity
Hydraulic operated air on/off and vent valves 1500psi rated 2” air hose with certified hoses socks 500psi rated 3” sample hose assembly with certified hose socks. Rotating wet splitter assembly Hydraulic operated adjustable rod kicker operated from foot pedal
Rod Handler EDM/KL Style RC 6m Rod Handler
Direct hydraulic actuation from rod handler console Remote control option 4” , 4.5” Diameter (Optional 5.5”) Rod Handling Capability
Hammer Lubricator
60 Liter ( 15 .8 Gal ) lubrication tank Air operated pump On/Off and flow control from control cabinet
Slips Table
Hydraulically opening multipurpose Slips RC Table Spanner included Hydraulically opens both front and rear Interchangeable slips bowls form 12” – 4” Max opening 20” Foot clamps designed to drop into slips table for diamond drilling
Air Circuit Rig Air circuit with 2 Auxiliary inlets 2” Airline from Inlet to Swivel Hydraulically actuated 2” Ball valves for air On/Off and Air Vent 100psi Pressure reducer for service Air Water injection into Air circuit
Cyclone
EDM Cyclone mounted to rear left Jack leg Hydraulic Up/Down Butterfly Valve for sample control Pivoted behind Rig for transport
RC Drilling Accessories
Bottom side entry air swivel Top mounted sample Swivel Head tube Blow down and Blowback valve if Required
Auxiliary Circuits
Independent auxiliary pump providing: One 25LPM (6GPM) mud mixing circuit operated from the control Cabi-net with adjustable flow Two 25LPM (6GPM) auxiliary circuits controlled directly from the valve Two 100LPM (26GPM) auxiliary circuits controlled directly from the valve One 60LPM (17GPM) auxiliary circuit controlled directly from the valve
Hydraulics
Rexroth pumps, Rexroth motors, Parker CVG main valve, Danfoss PVG auxiliary valves, Sun cartridges.
Rod Spin Guard
Cages off the rotating rods from the operator Hydraulically interlocked with rotation Reduces rotation to 150 RPM when cage is opened
Optional Features Clients color choice Fire suppression unit
• Hydraulic test points on all pumps, motors, and spool banks
• Lockable diesel tank fill points & Battery isolation switch
• Fuel tank gauge
• Clearly labeled oil type and grades on all oil fill points
• Two additional available spool banks, one with detent, one spring cen-tre for additional mud mixing systems, casing jacks
• All jaw sets from B+, N+, H+, P+.
• 10m ( 30 ft ) of 2 inch suction hose with foot valve and cam lock con-nectors
• Mast ladder
• Rig platform access ladders and steps
• Large fully adjustable offsiders platform
• EDM products are designed with standard imperial materials. All threads are either UNC or UNF. All hydraulic valves bodies, pumps, motors use common SAE O-ring boss adaptors
Warranty 1 Year / 5000 hrs
Safety Features
• Guards on all rotating equipment
• Anti slip surfaces on all work platforms
• Hand rails on all work platforms
• Emergency stops in control cabinet and on both sides of machine
• Heat guards on all exhaust manifolds and piping
• Murphy shut down system which protects the following
• Low engine oil pressure
• High engine temperature
• Low hydraulic tank oil level, coolant level
• 24 volt, 100amp alternator to enable high quality additional work lights