This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Memory/battery problems weredetected.The adapter has recovered, butcached data was lost.Press any key to continue, or 'C' toload the configuration utility.
RAIDコントローラ上のメモリまたはバッテリのエラーによって、キャッシュ内のデータがロストした。
保守サービス会社に連絡してください。
Firmware version inconsistency wasdetected.The adapter has recovered, butcached data was lost.Press any key to continue, or 'C' toload the configuration utility.
ファームウェアバージョンの不整合により、キャッシュ内のデータをロストした。
保守サービス会社に連絡してください。
Foreign configuration (s) found onadapterPress any key to continue, or 'C'load the configuration utility, or 'F' toimport foreign configuration (s) andcontinue.
Foreign configuration import did notimport any drives.Press any key to continue.
コンフィグレーションのインポートができなかった。
保守サービス会社に連絡してください。
Previous configuration cleared ormissingImporting configuration created onMM/DD hh:mmPress any key to continue, or 'C' toload the configuration utility.
An enclosure was found thatcontains both SAS and SATA drives,but this controller does not allowmixed drive types in a singleenclosure. Please correct theproblem then restart your system.Press any key to continue, or 'C' toload the configuration utility.
SAS drives were detected, but thiscontroller does not support SASdrives.Please remove the SAS drives thenrestart your system.Press any key to continue, or 'C' toload the configuration utility.
SATA drives were detected, but thiscontroller does not support SATAdrives.Please remove the SATA drives thenrestart your system.Press any key to continue, or 'C' toload the configuration utility.
The battery hardware is missing ormalfunctioning, or the battery isunplugged. If you continue to bootthe system, the battery-backedcache will not function. Pleasecontact technical support forassistance.Press 'D' to disable this warning (ifyour controller does not have abattery).
The battery is currently dischargedor disconnected. Verify theconnection and allow 30 minutesfor charging. If the battery isproperly connected and it has notreturned to operational state after30 minutes of charging then contacttechnical support for additionalassistance.
The battery is currently dischargedor disconnected. VDs configured inwrite-back mode will run in write-through mode to protect your dataand will return to write-back policywhen the battery is operational.IfVDs have not returned to write-back mode after 30 minutes ofcharging then contact technicalsupport for additional ssistance.The following VDs are affected: XXPress any key to continue.Your VDs that are configured forwrite-back are temporarily running inwrite-through mode.This is caused by the battery beingcharged, missing, or bad.Please allow the battery to chargefor 24 hours before evaluating thebattery for replacement.The following VDs are affected: XXPress any key to continue.
ディスプレイ上のエラーメッセージ
意 味 対処方法
130 障害時の対処
Invalid SAS Address present in MFCdata. Please program valid SASAddress, and restart your system.
不正なSASアドレスを検出した。
保守サービス会社に連絡してください。
Invalid SAS Address present in SBR.Please contact your systemsupport. Press any key to continuewith Default SAS Address.The cache contains dirty data, butsome VDs are missing or will gooffline, so the cached data can notbe written to disk. If this is anunexpected error, then please poweroff your system and check yourcables to ensure all disks arepresent. If you continue, the data incache will be permanently discarded.Press 'X' to acknowledge andpermanently destroy the cacheddata.
Some configured disks have beenremoved from your system, or areno longer accessible. Please checkyour cables and also ensure all disksare present.Press any key to continue, or 'C' toload the configuration utility.
The following VDs have missingdisks: xxIf you proceed (or load theconfiguration utility), these VDs willbe marked OFFLINE and will beinaccessible.Please check your cables andensure all disks are present.Press any key to continue, or 'C' toload the configuration utility.The following VDs are missing: xxIf you proceed (or load theconfiguration utility), these VDs willbe removed from your configuration.If you wish to use them at a latertime, they will have to be imported.If you believe these VDs should bepresent, please power off yoursystem and check your cables toensure all disks are present.Press any key to continue, or 'C' toload the configuration utility.All of the disks from your previousconfiguration are gone. If this is anunexpected message, then pleasepower off your system and checkyour cables to ensure all disks arepresent.Press any key to continue, or 'C' toload the configuration utility.The following VDs are missingcomplete spans: XXIf you proceed (or load theconfiguration utility), these VDs willbe removed from your configurationand the remaining drives marked asforeign. If you wish to use them at alater time, restore the missingspan (s) and use foreign import torecover the VDs. If you believe theseVDs should be present, pleasepower off your system and checkyour cables to ensure all disks arepresent.Press any key to continue, or 'C' toload the configuration utility.
ディスプレイ上のエラーメッセージ
意 味 対処方法
132 障害時の対処
Invalid memory configurationdetected. Please contact yoursystem support.System has halted.
RAIDコントローラ上のメモリの構成が不正です。
保守サービス会社に連絡しRAIDコントローラを交換してください。
RAID AdapterFW Failed Validation!!!Adapter needs to be reflashed.Press any key to continue.
RAIDコントローラ上のファームウェアが異常です。
保守サービス会社に連絡しRAIDコントローラを交換してください。
Cache data was lost due to anunexpected power-off or rebootduring a write operation, but theadapter has recovered. This couldbe due to memory problems, badbattery, or you may not have abattery installed.Press any key to continue or 'C' toload the configuration utility.
Multibit ECC errors were detected onthe RAID controller. The DIMM onthe controller needs replacement.Please contact technical support toresolve this issue. If you continue,data corruption can occur. Press 'X'to continue or else power off thesystem and replace the DIMMmodule and reboot. If you havereplaced the DIMM press 'X' tocontinue.
RAIDコントローラ上のメモリでマルチビットECCエラーを検出した。
保守サービス会社に連絡しRAIDコントローラを交換してください。
Single-bit ECC errors were detectedduring the previous boot of the RAIDcontroller. The DIMM on thecontroller needs replacement. Pleasecontact technical support to resolvethis issue. Press 'X' to continue orelse power off the system andreplace the DIMMmodule andreboot. If you have replaced theDIMM press 'X' to continue.
RAIDコントローラ上のメモリでシングルビットECCエラーを検出した。
保守サービス会社に連絡しRAIDコントローラを交換してください。
ディスプレイ上のエラーメッセージ
意 味 対処方法
運用・保守編 133
Single-bit overflow ECC errors weredetected during the previousBoot of the RAID controller. TheDIMM on the controller needsreplacement.Please contact technical support toresolve this issue. If you continue,data corruption can occur. Press 'X'to continue or else power off thesystem and replace the DIMMmodule and reboot. If you havereplaced the DIMM press 'X' tocontinue.
RAIDコントローラ上のメモリでシングルビットECCエラーを多数検出した。
保守サービス会社に連絡しRAIDコントローラを交換してください。
Entering the configuration utility inthis state will result in driveconfiguration changes. Press 'Y' tocontinue loading the configurationutility or please power off yoursystem and check your cables toensure all disks are present andreboot.
Attached Enclosure doesn't supportin controller's Direct mapping modePlease contact your system support.System has halted due tounsupported configuration.
DirectMappingモードでは接続されたエンクロージャをサポートしていない。
保守サービス会社に連絡しRAIDコントローラを交換してください。
Firmware did not find valid NVDATAimage. Please program valid NVDATAimage and restart your system Pressany key to continue.
RAIDコントローラのファームウェアがRAIDコントローラ上のNVDATAを見つけられない。
保守サービス会社に連絡しRAIDコントローラを交換してください。
There are offline or missing virtualdrives with preserved cache. Pleasecheck the cables and ensure that alldrives are present. Press any key tocontinue, or 'C' to load theconfiguration utility.
Upgrade Key Missing! An upgradekey was present on a previouspower cycle, but it is not connected.This can result in inaccessible dataunless it is addressed. Please re-attach the upgrade key and reboot.
The native configuration is no longersupported by the current controllerand firmware. Please ensure thatcorrect controller firmware is beingused.Press any key to continue, theconfiguration will be marked foreignand part of it may be imported ifpossible.
現在のコンフィグレーションがRAIDコントローラのファームウェアでサポートされていません。
保守サービス会社に連絡しRAIDコントローラを交換してください。
Invalid SAS topology detected.Please check your cableconfigurations, repair the problem,and restart your system.
→ WebBIOSのVirtual Drives-Properties画面のPolicies欄の「Default Write」は、RAIDコントローラのキャッシュモードの設定値を表示しており、「Current Write」が現在値を示しています。そのため、バッテリが接続されていない構成や、バッテリが異常な場合、充電が十分ではない場合は、「DefaultWrite」を「Write Back with BBU」に設定しても、「Current Write」の表示が「Write Through」に切り替わります。
The battery hardware is missing or malfunctioning, or the battery isunplugged, or the battery could be fully discharged. If you continue toboot the system, the battery-backed cache will not function.If battery is connected and has been allowed to charge for 30 minutesand this message continues to appear, then contact technical support forassistance.Press 'D' to disable this warning (if your controller does not have a battery).
Configuration on Disk(COD)機能は、コンフィグレーション情報を物理デバイス内部に記録する機能です。この機能により、RAIDコントローラが万一故障したときにRAIDコントローラを交換しても、コンフィグレーション情報が失われることはありません。RAIDコントローラ交換後、コンフィグレーション情報を物理デバイスから読み込み、正常に動作させることができます。