MEMSTYLE 138 Eaton’s MEM offers a wide range of pre-printed grid rockers, options modules and voice/data modules from the SPECTRA range. SPECTRA OPTIONS Existing 10A switches can be upgraded easily on site by replacing any module with an options alternative. Options offers neons, key switches, red rockers and broad rockers with grid type flexibility and plate switch convenience. VOICE/DATA The RJ45 interface is recognised as the data cabling to be installed at any desired stage of construction. Eaton’s MEM offer a full range of Voice/Data modules that snap into the front plate with no screws or tools required. Grid modules - metal rockers 139-140 Grid coverplate selection guide 146 Option modules 150 Options coverplate selection guide 151 Technical information 147-148 Voice/data modules 152 Voice/data coverplate selection guide 153 GRID The widest range of grid modules available with easy installation features. Choose from window rockers, pre-printed legends to neons, key switches and dimmer modules. All switches are X-rated, have the relevant BS number (where applicable) amperage, function of switch, reference number and even a circuit diagram marked on the base for easy identification.
16
Embed
Eaton’s MEM offers a wide range of pre-printed grid rockers, …pub/@eaton/@mem/... · Eaton’s MEM offers a wide range of pre-printed grid ... Part 1:1996 BS EN 60669:Part 1:1996
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
MEM
STYL
E
138
Eaton’s MEM offers a wide range of pre-printed grid
rockers, options modules and voice/data modules
from the SPECTRA range.
SPECTRA
OPTIONS
Existing 10A switches can be upgraded easily on site by replacing
any module with an options alternative. Options offers neons, key
switches, red rockers and broad rockers with grid type flexibility
and plate switch convenience.
VOICE/DATA
The RJ45 interface is recognised as the data cabling to be installed
at any desired stage of construction. Eaton’s MEM offer a full range
of Voice/Data modules that snap into the front plate with no screws
or tools required.
Grid modules- metal rockers 139-140
Grid coverplate selection guide 146
Option modules 150
Options coverplate selection guide 151
Technical information 147-148
Voice/data modules 152
Voice/data coverplateselection guide 153
GRID
The widest range of grid modules available with easy installation features.
Choose from window rockers, pre-printed legends to neons, key switches
and dimmer modules.
All switches are X-rated, have the relevant BS number (where applicable)
amperage, function of switch, reference number and even a circuit diagram
marked on the base for easy identification.
MEM
STYL
E
139
SPECTRA Modules range
X-Rated Gridswitches
F8004BHP 10A 2W gridswitch
‘push’ metal rocker
highly polished
F8004BPB 10A 2W gridswitch
‘push’ metal rocker
polished brass
F8004BSS 10A 2W gridswitch
‘push’ metal rocker
stainless steel
BSEN 60669:Part 1:1996
Standard grid modules will fitinto 25mm deep box.
10A GridswitchesMetal RockersBlack Surround
F8004BHP
F8000 10A 1W gridswitch
F8001 10A 2W gridswitch
F8002 10A 2W gridswitch
‘Bell’ push
F8003 10A 2W gridswitch
‘Fan’
F8004 10A 2W gridswitch
‘Push’
F8005 10A 2W gridswitch
‘Push’ red
BSEN 60669:Part 1:1996
Standard grid modules will fitinto 25mm deep box.
10A Gridswitches
F8000
Grid combines the flexibility and reliability of a modern modular
gridswitch system with a bold, attractive design. A wide range of cover
plates from 1 gang up to 24 gang are available with a choice of over a
100 different modules. From sliding dimmers, push off/on slide dimmers
to a 20amp DP switch with integral neon. All switches are X-rated to
eliminate the need to derate for fluorescent duty.
Every module in the Grid range has the relevant BS number (where
applicable), amperage, function of switch, reference number and
even a circuit diagram marked on the base for easy identification.
Wherever you need a grid system, Eaton’s MEM Grid is the system
of choice.
Widest range of modules available
Easy installation features
Simple ‘clip fit’ modules to grid
Window rockers and pre-printed legends
Metal fronted rockers
Key switches, neons and fused connection units
MEM
STYL
E
140
SPECTRA Modules range
X-Rated Gridswitches
F8020 20A 1W gridswitch
F8021 20A 2W gridswitch
F8022 20A intermediate gridswitch
F8023 20A DP gridswitch
F8024 20A 2W gridswitch centre off
F8033 20A 2W gridswitch
centre off bias
F8025 20A DP gridswitch with neon
F8026 20A 2W key gridswitch
F8027 20A DP key gridswitch
F8028 20A 2W key gridswitch bias
F8029 20A DP gridswitch
push to break
F8030 20A DP gridswitch
push to make
F8031 20A intermediate
key gridswitch
20A Gridswitches
F8020 F8024
F8025
BS EN 60669:Part 1:1996
Standard grid modules will fitinto 25mm deep box.
F8021BHP 20A 2W gridswitch metal rocker
highly polished
F8021BPB 20A 2W gridswitch metal rocker
polished brass
F8021BSS 20A 2W gridswitch metal rocker
stainless steel
F8022BHP 20A intermediate gridswitch metal rocker
highly polished
F8022BPB 20A intermediate gridswitch metal rocker
polished brass
F8022BSS 20A intermediate gridswitch metal rocker
stainless steel
F8023BHP 20A DP gridswitch metal rocker
highly polished
F8023BPB 20A DP gridswitch metal rocker
polished brass
F8023BSS 20A DP gridswitch metal rocker
stainless steel
F8024BHP 20A 2W gridswitch centre off
metal rocker highly polished
F8024BPB 20A 2W gridswitch centre off
metal rocker polished brass
F8024BSS 20A 2W gridswitch centre off
metal rocker stainless steel
20A Gridswitches Metal Rockers Black Surround
F8021BHP F8023BPB
F8024BHPF8030BPB
F8029BHP 20A DP gridswitch push to break
metal rocker highly polished
F8029BPB 20A DP gridswitch push to break
metal rocker polished brass
F8029BSS 20A DP gridswitch push to break
metal rocker stainless steel
F8030BHP 20A DP gridswitch push to make
metal rocker highly polished
F8030BPB 20A DP gridswitch push to make
metal rocker polished brass
F8030BSS 20A DP gridswitch push to make
metal rocker stainless steel
F8033BHP 20A 2W gridswitch centre off
bias metal rocker highly polished
F8033BPB 20A 2W gridswitch centre off bias
metal rocker polished brass
F8033BSS 20A 2W gridswitch centre off bias
metal rocker stainless steel
BS EN 60669:Part 1:1996
Standard grid modules will fitinto 25mm deep box.
MEM
STYL
E
141
SPECTRA Modules range
16A Gridswitches Indicator Units/Blank Other Grid Modules
F8060 Grid blank plate
F8060BHP Grid blank plate
metal front
highly polished
F8060BPB Grid blank plate
metal front
polished brass
F8060BSS Grid blank plate
metal front
stainless steel
F8061 Grid red neon
indicator
F8062 Grid amber neon
indicator
F8063 Grid green
fluorescent
indicator
F8032 16A SP gridswitch
twin module
F8070 16A 2 pin universal
grid module
F8071 Grid/TV co-axial
outlet
F8072 13A fused
connection unit
grid module
F8072A3 As F8072 printed
3A fuse
F8072A13 As F8072 printed
13A fuse
F8073 20A cord outlet
10mm grid module
F8074 13A fused
connection unit
screw retention
grid module
F8075 Grid/BNC type
computer socket
F8076 Grid/buzzer unit,
240v
F8040 10A 1W gridswitch
window rocker
F8041 10A 2W gridswitch
window rocker
F8045 20A 1W gridswitch
window rocker
F8046 20A 2W grid switch
window rocker
F8047 20A DP gridswitch
window rocker
BS EN 60669:Part 1:1996 BS EN 60669:Part 1:1996
BS EN 60669:Part 1:1996
Standard grid modules will fitinto 25mm deep box.
F8075 BNC outlet, 50 ohm,solder type 8073, 8076 - must be fitted in a 35mm +mounting box.
10A Window Rockers 20A Window Rockers
F8032 F8060 F8061
F8062 F8063
F8071 F8072
F8073 F8074
F8075 F8076
F8040 F8041 F8045
X-Rated Gridswitches and Window Rockers
BS EN 60669:Part 1:1996
MEM
STYL
E
142
SPECTRA Modules range
Dimmer Modules
F8064 40-250 watt tungsten – 2W
F8065 80-400 watt tungsten – 2W
F8067 50-250 VA low voltage – 2W
F8068 50-400 VA low voltage – 2W
F8066 100-630 watt tungsten, 2 module – 2W
F8069 60-400 watt fluorescent, 2 module – 2W
F8078 1-10v dimmer suitable for 1-10v dimmable fluorescent
ballasts, 1 module – switch required
Note: ref. F8066 and F8069 take up two modules (two gangs) in thegrid system and are supplied with a blank module ref. F8060.
Mounting Boxes should be at least 41mm deep to BS 4662.
See page 148 for wiring diagrams and further details.
Push ON/OFF Sliding Dimmer Modules
F8064
F8066
MEM
STYL
E
143
SPECTRA Modules range
Pre-Printed Rockers20A DP Gridswitch with Pre-Printed Legend
MOULDED PATTRESS FOR SURFACE MOUNTING WHITE MOULDED PLATES (28mm deep)
F4501 F4501 F4502 F4502
1 2 3 4 6 8 9 12 18 24 Architrave
*Add plate finish reference to complete order ie. U801SS
H - 100mm
W - 28mm
D - 30mm
MEM
STYL
E
147
SPECTRA Modules range
Grid Technical DataGrid
1. 2.
6.
4.3.
5.
Installing grid couldn’t beeasier. Just follow thesesimple instructions.
1. Push each module on to the grid, after preparing the cable tails in the mounting box.
2. Squeeze the ends of the module together to ensure that the switch has snapped on to the grid. No retaining screw or clip necessary.
3. Push hard on the switchto check that the ends have clipped firmly on to the grid.
4. Wire each individual switch module. All grid modules have wide terminal mouths able to take up to 3 x 2.5mm2 cable. The module reference number function and circuit diagram is printed clearly on the reverse for easy reference.
5. When the screws are fully tightened the grid is automatically positioned correctly for mounting the front plate. For metalclad surface applications remove the end clamps before screwing the grid to the mounting applications follow the instructions forflush mounting.
6. Attach the cover plate to the grid using the screws provided with thecover plate.
Standard grid modules• Current Rating: 10A or 20A - X-rated for fluorescent/
or inductive loads.• Voltage Rating: 240V A.C. 50Hz
Available labels for the window grid switch• Labels can be ordered ref. F8085
lounge
entrance
alarm
press
toilet
reception
kitchen
heater
ladies
spots
bell
fan
gents
garage
push
waterheater
lights
emergency
bar
stairway
Installation of label and windowfor window grid switch• Pre-printed labels and blanks
are available separately (ref. F8085) Once clipped intoplace the transparent windowsare NOT designed to beremoved from the switchmodule. The window can beaffixed prior to the mounting ofthe cover plate or afterwards.
MEM
STYL
E
148
SPECTRA Modules range
Grid Dimmer Modules
Grid Technical Data
Grid Dimmer Wiring and Set-Up
* For 11-50 ballasts a contactor will also be required.
Note: Ref. F8066 and F8069 take up two modules, (two gangs) in the grid system and are supplied with a blank module Ref. F8060.
Max total plate wattage 500 500 1000 1000 1500 1500 2000 2000 3000 4000
Loading Rules Table
Dimmers can be mounted in the same enclosure providing the total wattage (VA) loading being used is within the following guidelines:
A. Tungsten - Ref. F8064, F8065, F8066• One way switching - Live may go to terminal L1 or L2.• Two way switching - Use both terminals.
Note: that there are two methods for 2-way wiring, only onedimmer can be wired in each circuit (this dimmer may be fitted ineither position).
For dimming 230V Tungsten Halogen Lamps, de-rate dimmerby 50% (eg. F8065 maximum load becomes 200W).
B. Low Voltage Lighting - Ref. F8067, F8068• These Dimmers are for controlling wire-wound laminated and
some compatible dimmable electronic transformers Note: they are not suitable for use with toroidal transformers.
• Wire as for Tungsten Lighting, with the Variable Live to the 230V side of the transformer.
• The Dimmer VA rating represents maximum circuit load. Allow for Transformer Losses,typically 20% (15% for dimmable electronic transformers) i.e. maximum lamp load for 400VADimmer becomes 333W (347W for electronic), and 200VA becomes 208W (216W for electronic).
• Any mixture of transformer sizes may be used, providing maximum dimmer rating is not exceeded.
• All Eaton’s MEM Grid Dimmers are ‘leading edge dimmers’. These are not compatible withtransformers which require a trailing edge, phase-cutting or falling edge type dimmer.
• After installation and restoring power, move slider to minimum light, then adjust dimmer fordesired maximum light level (normally 20% light) ensuring that the light output is flicker free.(see fig.5)
Note:To overcome lamp flicker, loadresistors have to be fitted across thevariable live output (Com) and neutral.One load resistor is required for eachballast.Warning:Use of lower than minimum loadswith fluorescent dimmers will result indamage to the unit.
Fig. 5
1-Way WiringGrid Dimmer
Standard 2-Way Wiring Alternative 2-Way Wiring MethodGrid Dimmer Mechanical Switch Mechanical SwitchGrid Dimmer
VariableLiveCommon (C)Common (C)
(Note, for 2-way circuit, dimmer & switch may be swapped)
L1 L2
LiveFeed
VariableFeed
VariableFeed
LiveFeed
LiveFeed
L1 L2 COM L1 L2 L1 L2 COM L1 L2
Fig. 4
L1 L2 COM F1
Dimmer F8069 - UDT Control Gear
Load Resistors
Variable Live Ballast
UDT orUniversalDimmingTransformer
L
N
L
N
Switc
hed
Live
Fluorescent Lamp
Fig. 6
F8069 - EL-FD Control Gear
Fluorescent Tube
Dimmer 8069EL-FDHF Ballast
FilterChoke
FilterChokeL1 L2 F1COM
Load Resistors
L
N Fig. 7Variable Live
Product Lighting Minimum Maximum Grid Spaces No. of WaysCode Type Load Load Required
F8078 Fluorescent 1-10V 10/50 ballasts* 1 gang 2Wballasts plus switch
req.
F8083 Grid assembly for commercial dimming system
Typical wiring for dimmer 50Hz flu fittings.
MEM
STYL
E
149
SPECTRA Modules range
Options Modules
The availability of broad and half broad OPTIONS switch modules opens up
extensive possibilities for applications in ‘Lifetime’ and ‘Barrier-free’ homes
or sheltered accommodation where users may have limited dexterity.
Choose from 1 way, 2 way, intermediate and retractive modules.
Add key switches. Use red, amber or clear neons for circuit indicators,
switch locators for the elderly and bedroom comfort lights for children.
Include test switches for smoke detectors or emergency lights and
modules with red rockers for essential supply circuits. Wide red ‘panic’
warden call modules for the safety of the elderly.
OPTIONS modules offer contractor friendly features such as captive
terminal screws, backed off ready for insertion of the conductors and large
terminal screw heads so that one screwdriver can be used for connecting
and fixing a unit.
CHANGING OPTION MODULES COULDN’T BE EASIER
Neon, key and fan isolator for industrial use
MEM
STYL
E
150
SPECTRA Modules range
Options Modules
F1902 10A options module 1W switch
F1903 10A options module 2W switch
F1904 10A options module bell push
F1904P 10A options module push
F1905 10A options module intermediate
F1911 LF 2W half rocker module (left)
F1912 RT 2W half rocker module (right)
F1907 LF Bell push half rocker module (left) - 1W
F1908 RT Bell push half rocker module (right) - 1W
F1909 LF Intermediate half rocker module (left)
F1910 RT Intermediate half rocker module (right)
F1941 10A options module 2W key switch
F1942 10A options module 2W bias key switch
F1943 10A options module 2W ‘test’ key switch
F1944 10A options module 2W key switch red cover
F1920 10A options module 2W red rocker
F1921 10A options module 2W push red rocker
F1922 10A options module 2W push ‘test’ red rocker
F1927 10A options full broad 2W red rocker
F1928 10A options full broad 2W push ‘press’ red rocker
F1929 10A options full broad 2W push ‘emergency’ red rocker
F1923 LF Red 2W half rocker module (left)
F1924 RT Red 2W half rocker module (right)
F1925 LF Red bell half rocker (left) - 1W
F1926 RT Red bell half rocker (right) - 1W
F1945 10A options red neon module
F1946 10A options amber neon module
F1947 10A options clear neon module
F2455 Find-a-lite kit (location indicator for Options switches)
Options Modules
F1903 F1904
F1912RT
F1905
F1907LF F1908RT F1927 F1928 F1929
F1923LF F1926RT
F2455
F1942F1941 F1943
F1944 F1920 F1921 F1922 F1945 F1946 F1947
MEM
STYL
E
151
SPECTRA Modules range
1 Gang 1 Gang 2 Gang 3 Gang 4 Gang 1 Gang 2 Gang 3 Gang Fan 3 Pole1 Way 2 Way 2 Way 2 Way 2 Way Intermed. 1 Way 1 Way Isolator IsolatorSwitch Switch Switch Switch Switch Switch Switch Switch Switch Switch
1 Gang 2 Gang 1 Gang 1 Gang 1 Gang 1 Gang Double Double 2 Gang 4 Gang2 Way 2 Way Half Bell Push Intermed. 2 Way Half Intermed. Pole Pole with 2 Way 2 Way HalfSwitch Module Switch Switch Module Half Module Switch Neon Switch Module
4 Gang 1 Gang 6 Gang 1 Gang 2 Gang 1 Gang 1 Gang1 Way Bell Push 2 Way 2 Way 2 Way Light 1 WaySwitch Switch Switch Architrave Architrave Symbol Architrave
INTRA M014 M015 M026 M021A M022A M015L M011A
ULTRA U015* U026*
STAINLESS STEEL A015SS
UNCOATED STAINLESS STEEL A015US
SATIN BRONZE A015SB
HIGHLY POLISHED A015HP
XTRA X015MG
AURA MONARCH BRASS A015MB
OPTIONS STANDARD RANGE
1 Gang 2 Gang 3 Gang Half Broad 6 GangPlate Plate Plate Plate Plate
*To order ULTRA product finish please use existing ref. no. and add any suffix from list below:
Finishes available are: SS Stainless Steel PB Polished BrassWH White AN Anodised SilverHP Highly Polished AB Antique BronzeSB Satin Bronze AC Antique CopperBS Brass Satin MG Metallic Grey
* To order your chosen product with a Blackinsert use guide below:1. Use existing ref. no.2. Add B to the end of ref. no. indicating
insert eg. U021B3. Finally add plate finish ref. ie. SS to complete
order ref. no. eg. U021BSS
AURA
AURA
AURA
AURA
MEM
STYL
E
152
SPECTRA Modules range
Voice/DataAncillary EquipmentOutlet Modules
F3691 RJ45 outlet, IDC connections, Cat 5 E
F3696 BT phone module - master IDC (PBX)
F3697 BT phone module - secondary IDC
*D200 Keystone shutter module
*D210 Keystone jack RJ45, Cat 5 E
*D220 Keystone jack RJ11
F3694 Blank module
ISDN modules available on request.
Eaton’s MEM voice/data outlets are designed in accordance with BT specification D22 150.
* 37mm x 25mm size fits.
F3691
F3697
F3696 F3694
The RJ45 interface is now recognised
as the data cabling to be installed at any
desired stage of construction.
Eaton’s MEM offer a full range of modules
and cover plates in all moulded and metal
plate finishes, to suite with existing
accessories and grid switches.
Includes 4 outlet modules and
a series of ancillary products
for ease of installation.
Cover plates are offered in
1,2 or 4 module size.
Each module snaps into the
front plate with no screws or
tools required.
MEM
STYL
E
153
SPECTRA Modules range
Voice/Data coverplate selection guide
GANG 1 2 4
COVERPLATES
INTRA M851 M852 M854
PLATE DIMENSIONS (mm) 86x86 86x86 86x146
AURA
STAINLESS STEEL/MATT CHROME A851SS A852SS A854SS
HIGHLY POLISHED A851HP A852HP A854HP
SATIN BRONZE A851SB A852HP A854HP
PLATE DIMENSIONS (mm) 89x89 89x89 89x146
AURA MONARCH BRASS A851MB A852MB A854MB
PLATE DIMENSIONS (mm) 96x96 96x96 96x158
ULTRA U851* U852* U854*
PLATE DIMENSIONS (mm) 86x86 86x86 86x146
XTRA X851MG X852MG X854MG
PLATE DIMENSIONS (mm) 86x86 86x86 86x146
* To order ULTRA product finish please use existing ref. no and add any suffix from list below:
Finishes available are:
SS Stainless Steel
WH White
HP Highly Polished
SB Satin Bronze
BS Brass Satin
PB Polished Brass
AN Anodised Silver
AB Antique Bronze
AC Antique Copper
MG Metallic Grey
Voice/Data Quick Reference Chart
In floor box applications Voice/Data modules can be mounted toflat metal or plastic wall plate and in this case a minimumclearance of 20mm is required behind the plate.
Ref: F3691 is CAT 5E compliant unless otherwise stated. They aresuitable for use with wall plates in boxes of only 16mm depth.