-
E SeriesQuick Start GuideInput ConfigurationE Series two-way
loudspeakers and subwoofers are designed for externally powered
operation. Pass-throughs permit connection to multiple
loudspeakers. The two-way models feature internal passive
crossovers for full-range operation. To use them with subwoofers,
use an active crossover and separate amplification to split the
subwoofer frequencies and the remainder of the audio spectrum.
PLD and GXD Series amplifiers have E Series voicings available
in their presets and loudspeaker profiles. TouchMix digital mixers
also have E Series voicings available, for use in systems that
don't have PLD or GXD Series amplifiers.
E Series E110, E112, E115, E215 Block Diagram and Input
Plate
— Figure 1 —
LF
E215 only
DEEP LPF
HPF HF
LPF LF
NL4
BarrierStrip
NL4
1
1
1
1
22
22
E Series E118sw, E218sw Block Diagram and Input Plate
— Figure 2 —
LF
LF
NL4
BarrierStrip
NL4
1
1
1
1
E218sw only
22
22
TD-000525-00-E
*TD-000525-00*
-
2TD-000525-00-E
ConnectionsFull Range Stereo System
— Figure 3 —
Input
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Right
Left
Single Channel, Sub / Satellite Option 1
— Figure 4 —
Input
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
GXD Series power amplifier preset:P6 ST E110 (stereo E110) P10
ST E112 (stereo E112) P12 ST E112 DANCE (stereo E112 dance) P14 ST
E115 (stereo E115) P16 ST E115 DANCE (stereo E115 dance)
GXD Series power amplifier preset:P3 SUB SAT 80HZ
-
3TD-000525-00-E
Single Channel, Sub / Satellite Option 2
— Figure 5 —
Input
Cross-wired 1 - 2, 2 - 1
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Dual Channel, Sub / Satellite System
— Figure 6 —
to RightSubwoofer
to LeftSubwoofer
to LeftSatellite
to RightSatellite
Input
NL4Amplifier
NL4Loudspeaker
1122
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Right
Left
GXD Series power amplifier preset:P7 ST E110 + SUB P8 ST E110
DANCE + SUB P11 ST E112 + SUB P12 ST E112 DANCE + SUB P15 ST E115 +
SUB P17 ST E115 DANCE + SUB
GXD Series power amplifier preset:P3 SUB SAT 80HZ
GXD Series power amplifier preset:P18 ST E118 SUBS
-
4TD-000525-00-E
Dual Channel, Sub / Satellite System with 4-channel PLD
— Figure 7 —
Channels C & Dto RightSubwoofer &Satellite
Channel Bto LeftSatellite
Channel Ato LeftSubwoofer
Right
Input
Cross-wired 1 - 2, 2 - 1
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Option 1:Two 2-conductorcables
Option 2:4-conductorcable
Left
PLD Series power amplifier preset:F11 Dual bi-amp mode
PLD Series power amplifier loudspeaker profiles:
CH A • E118sw• E218sw
CH B • E110 +SUB• E112 +SUB• E112 dance +SUB• E115 +SUB• E115
dance +SUB• E215 +SUB• E215 dance + SUB
CH C • E118sw• E218sw
CH D • E110 +SUB• E112 +SUB• E112 dance +SUB• E115 +SUB• E115
dance +SUB• E215 +SUB• E215 dance + SUB
-
5TD-000525-00-E
Pole Mounting on E118swThe E Series loudspeakers (E110, E112,
E115) can be mounted above the E118sw subwoofer using the 36-inch
pole included with the subwoofer. NOTE: The E215 loudspeaker does
not offer a pole mounting option.
WRNINNG: This pole, if used inappropriately, may make the
loudspeaker system top-heavy and hazardous. Ensure that your system
will resist tipping and that it sits on a solid, level surface.
WRNINNG: Always use two persons to lift the loudspeaker onto the
pole. Do not move a subwoofer if a loudspeaker and pole are mounted
on it.
Refer to — Figure 8
1. Place the E118sw subwoofer (1) on a solid level surface
positioned where you want to use it.
2. Screw the threaded end of the 36-inch mounting pole (3)
clockwise into the pole-mounting bracket (2) on top of the
subwoofer. Hand tighten only.
3. Select one of the two pole mount cups on the E Series
loudspeaker:
• The rear cup (4) has no tilt.
• The front cup (5) gives a downward tilt of 10°.
4. Carefully place the loudspeaker onto the pole.
Installation OptionsThe following options require purchasing an
accessory kit designed for the E Series loudspeakers.
Yoke Mounting the Loudspeakers
A yoke accessory allows the E110, E112, or E115 to be mounted on
a surface, such as a wall or ceiling. The E118sw and E218sw
subwoofers cannot be yoke-mounted. Each model has a corresponding
yoke accessory kit:
• E110 Yoke Accessory Kit: E110 Yoke
• E112 Yoke Accessory Kit: E12 Yoke
• E115 Yoke Accessory Kit: E15 Yoke
Suspending the Loudspeakers
A pair of E110 loudspeakers can be suspended using the M8
Suspension Kit M8 KIT W, which contains six eye bolts and six
washers.
To suspend an E112, E115, or E215 loudspeaker, use the M10 KIT-
, which contains three eye bolts.
The E118sw and E218sw subwoofers cannot be suspended.
Always consult a licensed and qualified rigger or structural
engineer before suspending any loudspeaker.
Subwoofer Caster Kits
Optional casters are available to install on the subwoofer
models to make them more mobile and ideal for use in portable sound
systems.
Both the E118sw and the E218sw subwoofers use a kit of two
locking and two non-locking 4-inch casters with 16 mounting screws,
QSC part number FG-901156-00 (one kit needed per subwoofer).
— Figure 8 —
54
3
2
1
-
6TD-000525-00-E
Mailing Address:
QSC, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626-1468 USA
Telephone Numbers:
Main Number: +1 (714) 754-6175
Sales & Marketing: +1 (714) 957-7100 or toll free (USA only)
(800) 854-4079
Customer Service: +1 (714) 957-7150 or toll free (USA only)
(800) 772-2834
Facsimile Numbers:
Sales & Marketing FAX: +1 (714) 754-6174
Customer Service FAX: +1 (714) 754-6173
World Wide Web:
www.qsc.com
E-mail:
[email protected]
[email protected]
[email protected]
© 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are
registered trademarks of QSC, LLC in the U.S. Patent and Trademark
office and other countries. All other trademarks are the property
of their respective owners.
http://patents.qsc.com.