DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT CENTER OF GRAVITY(C.G.) DECAL: 1 Apply glue on the contact area of the left and right wing, then glue them together. 7 Install the horizontal stabilizer and vertical stabilizer. 13 Glue the scale exhaust. 2 Secure the wing onto the fuselage with PM3*35mm screws. 8 Secure the rear wheel onto the fuselage with a 1.5mm hexangular screwdriver. 14 Install the propeller. 3 Secure spare parts with PA2.3*5mm screw. 9 15 Install the spinner with PA2.5*8mm screws. 4 Glue the plastic parts. 10 16 Glue the pilot in place. 5 Connect the aileron servos with the Y wires. 11 17 Glue the canopy. 6 12 Glue the scale antenna. 18 DY8966 Wingspan Length Flying Weight Wing Area Wing Load Radio System Power Battery : 1250mm (49.2in) : 1003mm (39.48in) : 1460g (51.6oz) : 26dm² : 56g/dm² : 5 Ch TX and 7 Ch RX : Brushless System : LIPO, 2200 mAh, 14.8V ASSEMBLY: DYR-2001 2.4G Receiver HURC-01 Fuselage SPARE PART LIST: HURC-02 Wing HURC-03 Elevator DY-6015 14.8V 2200mAh 25C Battery BM3720A-KV600 Brushless Motor BM3720A-KV600-Shaft Motor Shaft DY-3003 Glue Control Throw Setting Suggestion Elevator Aileron Rudder 14.8V 2200mAh Li-Po, 25C (13x7x3) ESC-skylord 40A ESC-40A Lithium-polymer Battery 2200mAh 14.8V 25C Discharge Rechargeable Cells Use li-po charger only MOTOR Dynam RC dynam-rc.cn of This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle. over 65 70 65 70 1 10 11 9 2 3 4 5 7 19 20 6 HURC-05 Spinner HURC-07 Landing Gear HURC-08 Foam Pieces HURC-06 Pilot DYP-1020 13*7*3 Propeller DY-1007 9g Servo HURC-13 Decal 0 DY-1052 E-Retract ø3.6 90 HURC-12 Push Rod HURC-11 Servo Horn HURC-09 Plastic Parts HURC-10 Blister Parts HURC-04 Vertical Stabilizer Open the canopy this way. Connect the elevator push rod as shown. Connect the rudder push rod as shown. Secure the stabilizers with PA2.3*20mm screw. Apply glue on the contact area of the elevator. Glue the elevator onto the fuselage. glue PM3*35mm HURC-15 Cockpit HURC-16 Blade Holder HURC-14 Moto Mount skylord 40A ESC DTM-T006 6A Transmitter
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT
CENTER OF GRAVITY(C.G.)
DECAL:
1 Apply glue on the contact area of the leftand right wing, then glue them together.
7 Install the horizontal stabilizer and verticalstabilizer.
13 Glue the scale exhaust.
2 Secure the wing onto the fuselage with PM3*35mm screws.
8 Secure the rear wheel onto the fuselage with a 1.5mm hexangular screwdriver.
14 Install the propeller.
3 Secure spare parts with PA2.3*5mm screw.
9
15 Install the spinner with PA2.5*8mm screws.
4 Glue the plastic parts.
10
16 Glue the pilot in place.
5 Connect the aileron servos with the Y wires.
11
17 Glue the canopy.
6
12 Glue the scale antenna.
18
DY8966WingspanLengthFlying WeightWing Area Wing LoadRadio SystemPowerBattery
: 1250mm (49.2in): 1003mm (39.48in): 1460g (51.6oz): 26dm² : 56g/dm²: 5 Ch TX and 7 Ch RX : Brushless System: LIPO, 2200 mAh, 14.8V
ASSEMBLY:
DYR-2001 2.4G Receiver
HURC-01 Fuselage
SPARE PART LIST:
HURC-02 Wing HURC-03 Elevator
DY-6015 14.8V 2200mAh25C Battery
BM3720A-KV600 Brushless Motor BM3720A-KV600-ShaftMotor Shaft
DY-3003 Glue
Control Throw Setting Suggestion
Elevator Aileron Rudder
14.8V 2200mAh Li-Po, 25C
(13x7x3)
ESC-skylord 40A
ESC-40A
Lithium-polymer Battery
2200mAh 14.8V25C Discharge
Rechargeable CellsUse li-po charger only
MOTOR
Dynam RC
dynam-rc.cn
of
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle.
over
65 70 65 70
1
10 11
923 4
5 719 20
6
HURC-05 Spinner HURC-07 Landing Gear HURC-08 Foam PiecesHURC-06 Pilot
DYP-1020 13*7*3 Propeller DY-1007 9g ServoHURC-13 Decal
0DY-1052 E-Retract ø3.6 90
HURC-12 Push RodHURC-11 Servo HornHURC-09 Plastic Parts HURC-10 Blister Parts
HURC-04 Vertical Stabilizer
Open the canopy this way.
Connect the elevator push rod as shown.Connect the rudder push rod as shown.Secure the stabilizers with PA2.3*20mm screw.
Apply glue on the contact area of the elevator. Glue the elevator onto the fuselage.
glue
PM3*35mm
HURC-15 Cockpit HURC-16 Blade Holder
HURC-14 Moto Mountskylord 40A ESC
DTM-T006 6A Transmitter
Related Documents
