DYDAC MICROPROCESSOR BASED HOT RUNNER TEMPERATURE CONTROLLER Microprocessor Based Auto – Tune PID Temperature Controller Accepts J ,K ,R, S, T Type Thermocouple ( Soft Start) bake out feature prevents moisture at startup Auto/Manual Transfer Accuracy of +/- 1 Deg. C. Internal Solid state triac/ SCR, triggered by Phase angle Firing. Dual displays for Process and Set Temperatures High Speed Fuses 16 A protection Fuses New Series with Short Circuit protection of Power Modules by C Curve MCB Latest Generation PID algorithm. Power Controller can take 3600 or 5000 Watts at 240 VAC In case of thermocouple Failure you can set the Power Manually by not stopping The production. Auto -Tune PID Temperature Controller Heaters life is extended to 10 times PID Temperature controller has bar graph indication of percentage output going to
11
Embed
DYDAC MICROPROCESSOR BASED HOT RUNNER ......MOLD POWER CABLES Mold power cables are used to connect the mainframe to the power input connector located on the mold. All cables are wired
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
DYDAC MICROPROCESSOR BASED HOT RUNNER TEMPERATURE CONTROLLER
Microprocessor Based Auto – Tune PID Temperature Controller
Accepts J ,K ,R, S, T Type Thermocouple
( Soft Start) bake out feature prevents moisture at startup
Auto/Manual Transfer
Accuracy of +/- 1 Deg. C.
Internal Solid state triac/ SCR, triggered by Phase angle Firing.
Dual displays for Process and Set Temperatures
High Speed Fuses 16 A protection Fuses
New Series with Short Circuit protection of Power Modules by C Curve MCB
Latest Generation PID algorithm.
Power Controller can take 3600 or 5000 Watts at 240 VAC
In case of thermocouple Failure you can set the Power Manually by not stopping
The production.
Auto -Tune PID Temperature Controller
Heaters life is extended to 10 times
PID Temperature controller has bar graph indication of percentage output going to
heaters.
PID Temperature Controller is CE Compliant and Phase Angle Power CE Compliant.
The Power Controllers are Phase Angle Fired and are Variable Power Controllers which
gives as much Power to the Heaters as required to maintain the Temperature thus saving
the Energy ( Energy Conservation at Set Point) and increasing life of the heaters and less
Production Break Down.
Alarm Option for over shooting and under shooting of Temperature. In case Thermocouple
Fails it will give Alarm
Available in 1,2,3,4,5,6,8,10,12,14,16,20 &24 Zones
Selection of Heater Current Load
16 Amps
32 Amps
MOLD POWER AND THERMOCOUPLE CABLES ( COMBINATION )
More specifically designed for the plastic industry by process of hot runner injection
molding, Dydac manufactures mold power and mold thermocouple cables designed
specifically for your mold and temperature controller connections. Working hand-in-hand with processors as well as mold makers,any configuration or adaptor cable that is best suited for
your individual process.can assist with cable design, cable and connector selections. With our just manufacturing capabilities, Dydac can produce cables on demand.
MOLD POWER CABLES
Mold power cables are used to connect the mainframe to the power input connector located
on the mold. All cables are wired for 5, 8, or 12 (rated @ 15A) zones as well as units working
on 30A. Mold power cables are available in any length, 10 and 20 feet are standard stocked
cables
NO. OF ZONES 10 FEET CABLE 20 FEET CABLE
5 PC5Z-10 PC5Z-20
8 PC8Z-10 PC8Z-20
12 PC12Z-10 PC12Z-20
MOLD THERMOCOUPLE CABLES
Mold thermocouple cables are used to connect the mainframe to the thermocouple connector
on the mold. Cables are wired for 5, 8, or 12. In most cases the connections on the controller
remain constant, while the connector on the mold end can vary. Mold thermocouple cables are
available in any length, 10 and 20 feet are standard stocked cables
NO. OF ZONES 10 FEET CABLE 20 FEET CABLE
5 TC5Z-10 TC5Z-20
8 TC8Z-10 TC8Z-20
12 TPC12Z-10 TC12Z-20
CE AXIS HOT RUNNER TEMPERATURE CONTROLLER
TECHNICAL SPECIFICATIONS
PERFORMANCE SPECIFICATION
OUTPUT SPECIFICATIONS
Auto Control Mode: Control Accuracy: Temperature Range: Temperature Stability: Calibration Accuracy: Power Response Time: Process Sampling:
F / c:
Computer-Calcu Cycle System +-0.1 F(+-0.1 c ) dependent on the total thermal system 32 to 999 F (0 to 537 c) +-0.5% of full scale over the ambient range of 32 to 131 F (0 to 55 c) Better than 0.2% of full scale Better than 0.3 second 100 milliseconds Jumper-selectable
Voltages: 110 Vac or 240 Vac nominal, single phase
Power Capability: 15 amperes, 3600 watts 240 Vac 15 amperes, 1800 watts 120 Vac Overload Protection: Triac and load use high speed fuses, Both side are Fused(ABC-15 GBB) Power Line Isolation: Optically and transformer isolated from ac line. Isolation voltage is greater than 2500 volts Output Drive: Internal solid state triac, triggered by ac zero crossing pulses CONTROLS AND INDICATORS
AdjComp Step Control Mode: AdjComp Step System Duration: AdjComp Step Output Voltage: AdjComp Step Override Temp.: Manual Control
Variable stepping voltage, phase fired Approximately 5 minutes Steps approximately from 25v RMS with 240Vac line output phase-fired 221 F (105 c)
Setpoint Control: % Power Control: Mode Control: Display: Status Indicators: Power On-Off:
Two buttons up or down
Resolution:1 F (1 c) Two buttons up and down: Push button switch with LED indicator for manual mode TOP: 3-digit filtered LED BOTTOM: 4-digit filtered LED Heater output,Soft-Start,Manul,alarm Rocker Switch,UL,CSA approved
Compensated: Operational Mode Priority:
Adjustable from 0-100% Maintain output Power to with 1% of setting a.TC open, TC reverse,TC shorted
Shutdown and Open heater override AdjComp step System
b.Manual mode override TC open, TC reverse
ELECTRICAL POWER SPECIFICATIONS Input Voltage: 110 ~ + 240 Vac,-10% Voltage Frequency: 50-60 HZ DC Power Supplies: Internally generated, regulated
and temperature compensated Module Power Usage: less than 6 watts,exciuding Dimensions: load 2" W * 7" H * 71/2" D
(5.08cm * 17.78cm * 19.05cm)
HOT RUNNER CONNECTORS
3+/4 Pin connector’s
3+/4+ Pin male Connector 3+/4+ Pin Female Connector 3+/4+ Pin Top 3+/4+ Pin side 3+/4+ Pin bottom 3+/4+ Pin bottom hood hood housing housing with cover
5+PE Pin connector’s
5+PE Pin male 5+PE Pin Female 5+PE Pin Top hood 5+PE Pin side hood 5+PE Pin bottom 5+PE Pin bottom housing Connector Connector housing with cover
6 Pin connector’s
6 Pin Male Connector 6 Pin female connector 6 Pin Top hood