SIGALARM MODEL 210 DS350 (RCL) For Lattice Boom Cranes SERVICE MANUAL
SIGALARM MODEL 210
DS350 (RCL) For Lattice Boom Cranes
SERVICE MANUAL
Service Manual – 1225/1229 Console
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
NOTICE
SkyAzúl makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and/or its fitness for a particular purpose.
SkyAzúl will not be liable for errors contained in this manual or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual. This document contains proprietary information, which is protected by copyright, and all rights are reserved.
No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of SkyAzúl.
SkyAzúl reserves proprietary rights to all drawings, photos and the data contained therein. The drawings, photos and data are confidential and cannot be used or reproduced without the written consent of Hirschmann. The drawings and/or photos are subject to technical modification without prior notice.
All information in this document is subject to change without notice.
MANUAL REVISIONS
REV DATE NAME DESCRIPTION
- 05/10/11 SC DS350 LS108 Service Manual (SkyAzúl) Rev 12/2000
SkyAzúl, Inc. 16 Walnut Street Middletown, MD 21769 Fax 301-371-0029 [email protected]
DS350 Rated Capacity Indicator System
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
TABLE OF CONTENTS
NOTICE
GENERAL INFORMATION...................................................................................1
WARNINGS..........................................................................................................1
1.0 ERROR CODE CHART ..................................................................................2
2.0 SYSTEM COMPONENT LAYOUT .................................................................6
3.0 ANGLE SENSOR ADJUSTMENT ..................................................................7
3.1 ANGLE CIRCUIT (WG203)......................................................................83.2 ANGLE CIRCUIT (WG206)......................................................................9
4.0 LINERIDER SETTINGS AND ADJUSTMENTS............................................10
4.0 General Information................................................................................10 4.1 Linerider Zero Point Adjustment.............................................................11 4.2 Linerider Output Adjustment...................................................................12 4.3 Linerider Circuits ...................................................................................13 4.4 Linerider Cannon Connection.................................................................14
5.0 DIGITAL INPUTS..........................................................................................15
6.0 ANTI-TWO BLOCK.......................................................................................16
7.0 BOOM BASE CABLE REEL DIAGRAM .......................................................16
8.0 MAIN BOOM / JIB JUNCTION BOX DIAGRAMS .........................................17
9.0 LUFFING JIB JUNCTION BOX DIAGRAMS.................................................18
10.0 SYSTEM ( 12 VOLT ) WIRING DIAGRAM .................................................19
10.1 Vertical Console Diagram ....................................................................20
11.0 SYSTEM ( 24 VOLT ) DIAGRAM................................................................21
11.1 Horizontal Console Diagram ................................................................22
12.0 TERMINAL BOARD DESIGNATIONS........................................................23
13.0 MAIN BOARD MEASURING POINTS ........................................................24
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
Service Manual – 1225/1229 Console
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
GENERAL INFORMATION
This handbook defines the error codes, cause, and actions to troubleshoot thePAT DS 350 Rated Capacity Limiter (RCL) System for Link-Belt Lattice-Boom Cranes.
Refer to the operating handbook for operation and maintenance of the PAT DS 350Rated Capacity Limiter (RCL).
This system assists the crane operator in promoting efficient operation by monitoringcrane loads and by warning the operator of approaching overload conditions. Alwaysrefer to operational instructions and load charts provided by the crane manufacturer forspecific crane operation and load limits.
WARNINGS
• The operator is always responsible for operating the crane within the manufacture’sspecified parameters.
• The PAT DS 350 Rated Capacity Limiter (RCL) is an operational aid which warns a
crane operator of an approaching overload and over hoist condition which couldcause damage to equipment, property, and/or injury to the operator or bystanders.
• This device is not, and shall not be a substitute for good judgment, experience, and
the practice of accepted safe crane operation. • The operator is solely responsible for the safe operation of the crane and must
observe and obey all warnings and instructions supplied by PAT and the cranemanufacturer.
• Prior to operating a crane, the operator must carefully and thoroughly read and
understand the information in operator’s handbook and the crane manufacturer’smanual to ensure that the operator understands the function and limitations of theRCL system and the crane.
• Proper operation of the RCL System is dependent upon proper inspection,maintenance, and observance of the operating instructions.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 1
301-371-6126
1.0 ERROR CODE CHART
ERRORDISPLAY
ERROR CAUSE ACTION
E 01 Fallen below radius orangle range
Fallen below the minimum radius orangle given in the load chart due torising the boom too far.
Put boom back to a radius orangle given in the load chart.
E 02 Radius or angle rangeexceeded.
The maximum radius or angle given inthe load chart was exceed due tolowering the boom too far.
Raise boom back to a radiusor angle given in the loadchart.
E 03 Prohibited slewingrange (no load area).
Slewing range prohibited with load. Slew back into permissiblerange.
E 04 Operating mode notavailable.
Operating mode switch on the consoleset incorrectly.
Set operating mode switchcorrectly to the codeassigned to the operatingmode of the machine. (seeSection 9 operator’shandbook)
E 06 Angle luffing jibexceeded.
The minimum angle given in thecorresponding load chart wasexceeded due to lowering the luffingjib too much.
Raise luffing jib to an anglegiven in the load chart.
E 07 No acknowledgesignal from overloadrelay.
Over load limit switch relay is stuck,defective, or not being selected.
Replace relay
E 08 No acknowledgesignal from hoist limitswitch relay
Hoist limit switch relay is stuck,defective, or not being selected.
Replace relay
E 09 No acknowledgesignal from relay 2.
Relay 2 is stuck, defective, or notbeing selected.
Replace relay
E 13 Fallen below lowerlimiting value for themeasuring channel“auxiliary force”.
Cable from central unit to the forcetransducer defective or water in theplugs.
Electronic component in themeasuring channel defective.
Check cable and plugs;replace items as necessary.
See Section 3, forcetransducer adjustments.
E 14 Fallen below lowerlimiting value for themeasuring channel“force-main hoist”.
Cable from central unit to the forcetransducer defective or water in theplugs.
Electronic component in themeasuring channel defective.
Check cable and plugs;replace items as necessary.
See Section 3, forcetransducer adjustments.
E 15 Fallen below lowerlimiting value for themeasuring channel“angle main boom”.
Cable from central unit to the anglesensor defective or loose, or water inthe plugs.
Electronic component the measuringchannel defective.
Check cable and plugs;replace items as necessary.
See Section 2, angle sensoradjustments.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 2
301-371-6126
1.1 ERROR CODE CHART - continued
ERRORDISPLAY
ERROR CAUSE ACTION
E 16 Fallen below lowerlimiting value for themeasuring channel“angle luffing jib”.
Cable from central unit to the anglesensor defective or loose, or water inthe plugs.
Electronic component the measuringchannel defective.
Check cable and plugs;replace items as necessary.
See Section 2, angle sensoradjustments.
E 18 Error in the referencevoltage.
Electronic component on main boarddefective.
Replace main board & resetforce transducers as shownin Section 3.2.
E 19 Error in the referencevoltage.
Electronic component on main boarddefective.
Replace main board & resetforce transducers as shownin Section 3.2.
E 20 No analog voltage. Crane voltage to low
Short in supply voltage from crane tocentral unit.
Voltage converter is defective on mainboard
Check crane voltage
Check wiring
Replace main board & resetforce transducers as shownin Section 3.2.
E 23 Upper limiting valuefor the measuringchannel “auxiliary-force” exceeded.
Cable from central unit to the forcetransducer defective or water in theplugs.
Electronic component in themeasuring channel defective.
Check cable and plugs;replace items as necessary.
Replace main board & resetforce transducers as shownin Section 3.2.
E 24 Upper limiting valuefor the measuringchannel “force - mainhoist” exceeded.
Cable from central unit to the forcetransducer defective or water in theplugs.
Electronic component in themeasuring channel defective.
Check cable and plugs;replace items as necessary.
Replace main board & resetforce transducers as shownin Section 3.2.
E 25 Upper limiting valuefor the measuringchannel “angle mainboom” exceeded.
Cable from central unit to the anglesensor defective or loose, or water inthe plugs.
Electronic component the measuringchannel defective.
Check cable and plugs;replace items as necessary.
See Section 2, angle sensoradjustments.
E 26 Upper limiting valuefor the measuringchannel “angle luffingjib” exceeded.
Cable from central unit to the anglesensor defective or loose, or water inthe plugs.
Electronic component the measuringchannel defective.
Check cable and plugs;replace items as necessary.
See Section 2, angle sensoradjustments.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 3
301-371-6126
1.2 ERROR CODE CHART - continued
ERRORDISPLAY
ERROR CAUSE ACTION
E 28 Error in the referencevoltage.
Electronic component on main boarddefective.
Replace main board & resetforce transducers as shownin Section 3.2.
E 31-34 Error in systemsoftware.
Eprom’s with system softwaredefective.
Replace system Eprom
Replace main board & resetforce transducers as shownin Section 3.2.
E 37 Error in systemsoftware.
Eprom’s with system softwaredefective.
Replace system Eprom
Replace main board & resetforce transducers as shownin Section 3.2.
E 38 Wrong system ordata Eprom.
Eprom’s with system software doesnot correspond with data Eprom.
Replace system Eprom
E 41-42 Error on the ram. Ram range on the main boarddefective.
Replace main board & resetforce transducers as shownin Section 3.2.
E 45 Error in internalcommunications
Error in read/writememory.
Electronic component on main boarddefective.
Electronic component on main boarddefective
Replace main board & resetforce transducers as shownin Section 3.2.
E 51-59 Error in data memory. Data Eprom's defective
Electronic component on main boarddefective.
Replace data Eprom
Replace main board & resetforce transducers as shownin Section 3.2.
E71 Incorrectacknowledgment ofthe 1. Relay on theterminal board a101.
Anti two-block relay is stuck ordefective.
Anti two-block relay is not beingselected due to a break on theterminal board a101, main board orribbon cables.
Replace 1. Relay.
Check terminal board a101,main board and ribboncables as well as replacedefective part, if necessary.
E72 - 77 analogous to E71 forthe relays 2...7.
Analogous to e71 for the relays 2...7. Analogous to E71 for therelays 2..7.
E89 Change of theoperating code duringlifting a load.
The operating mode switch in theconsole was used during lifting a load.
Lower the load and set theoperating mode switchcorrectly to the codeassigned to the actualoperating mode of the crane.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 4
301-371-6126
1.3 ERROR CODE CHART - continued
ERRORDISPLAY
ERROR CAUSE ACTION
E 91-92 No data transmissionfrom console.
Plug on console loose; cabledefective.
Check cable and plug;replace console, asnecessary.
E 93-94 Error in the datatransmission to theconsole.
Cable to the console not plugged in orinterrupted.
Eprom not installed or defective
Defect in the central electronics (mainboard).
Check cable; attach plugproperly.
Replace Eproms
Replace main board & resetforce transducers as shownin Section 3.2.
E-19/20/29 Error in reference supply voltage. Identify supply voltage that is beingshorted, (+/-5 or + -9) disconnect ribbon cable. If power supply returns then problem isexternal. Reconnect ribbon cables and disconnect all components individually to identifythe location of the short.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 5
301-371-6126
2.0 SYSTEM COMPONENT LAYOUT
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 6
301-371-6126
Au
x.
Lin
e R
ide
r S
KM
5
00
Au
x.
A2B
S
wit
ch
03
1-3
00
-10
0-5
07
Ma
in
SK
M
Ju
nc
tio
n
Box
0
31
-30
0-1
00
-52
2
Co
nso
les
[Q~'iiml'l
1c»:
:::::J
<>
Illl
I"
~
Wis
ke
r S
wit
ch
Lu
ffin
g
Jib
A
ng
le
Se
ns
or
00
6-4
20
-30
6-0
01
An
gle
S
en
so
r 0
06
-42
0-3
06
-00
1
o 0
----.
50
0
Mai
n
Ju
nc
tio
n
Box
0
31
-30
0-1
00
-44
6
Au
x.
Lin
e R
ide
r S
KM
5
00
03
1-3
00
-10
0-5
07
C
ab
le
Ree
l C
an
iste
r 0
31
-30
0-1
00
-42
4
Lim
it
Sw
itch
~'
Au
x.
Ce
ntr
a I
Pro
ce
ss
ing
U
nit
Ju
nc
tio
n
Bo
x
A2B
S
wit
ch
0
31
-30
0-1
00
-50
7
to
Cra
ne
P
ow
er
&
Ac
ce
ss
ori
es
~r--
3.0 ANGLE SENSOR ADJUSTMENT
The angle φ shown in Figure 1 needs to be within +0, -0.4 of the actual angle of theboom. Check boom angle at base/heel Section only. After adjustment, compare theactual boom angle with the displayed angle at about 0°, 30° and 60°. To comply with theSAE J375 standards the displayed angle must be +0.0° to -2.0° of the actual angle.
WG 203
φ φ
Figure 1. Angle Sensor Adjustment.
The supply voltage can be checked directly at the cannon connection. Using adigital volt meter measure between pins A and C, (A=GND, C= - 5V). If this voltage isnot correct refer to the system wiring diagram and verify all cable connections. You mayneed to start at the main board and check the supply voltages at their proper measuringpoints.
The following 2 drawings show the theory of operation for the main and luffing anglesignals.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 7
301-371-6126
3.1 ANGLE SENSOR CIRCUIT (WG203)
DRAWING # - LKB24-03
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 8
301-371-6126
BOOM ANGLE SENSOR PENDULUM
~ --WG 203 FIXED RESIST OR +90" (PART OF THE ANGL E
~5" POTENTIOMETER)
:!:'::!ili!i!i!:i:::!:
0"
ANGLE SENSOR
~
"
FIXED
"MINIMUM SI GNAL" -1.875V = +90' ANGLE
B
"MAXIMUM S IGNAL" -3.12SV = O' ANGLE
RESIST OR
TO AID CONVERTER
AM P:::e-...... ----1~
MP 8 TEST POINT
CH. #5 (PART OF THE ANGL E OPERATING POTENTIOMETER)
WINDOW I ERROR CODE
ERROR CODE
r/ (,,(~ .OV
fL-~"--L--1.500V MAX.
WORKING RANGE
P--o~--r~ 4.SV MAX.
E 25 ~L.c~'-J S.OY
MP 8 VOLTAGES +90' ANGLE MIN. SIG. = +SOOmV (.SOOY)
+45' ANGLE = +2.50V
O' ANGLE MAX. SIG. = +4.S0V
NOTE: ALL VOLTAGES ARE MEASURED WITH REFERENCE TO GND (TERMINAL Xl-16 OR MP15)
ON MAIN BOARD
C --D---- 3 ----lI2l -5. 0 V
1U
-#-WIRE NUMBER
1U --D-- CENTAL UNIT
TERMINAL BOARD
-0- TEST POINT ON MAIN BOARD
3.2 ANGLE SENSOR CIRCUIT (WG206)
DRAWING # - LKB24-04
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 9
301-371-6126
LUFFING JIB ..1
A Xl
D- 1 ---@ fG~6) ANGLE SENSOR
WG 206 FIXED RESIST +90 0 (PART OF THE
OR E ANGL
POTENTIOMETER)
0 0
',',',' ~}~ "" "MINIMUM 51 GNAL" TO AID
CONVERTER -90 0 ~ -1.875V =
B ANGLE
SENSOR
"" "MAXIMUM ~ -3.12SV =
FIXED RESIST
+90· ANGLE
D-2
51 GNAL" -90· ANGLE
A M p.:;:e ..... ----1~
MP 9 TEST POINT
CH. #6 (PART OF THE OR E ANGL
OPERATING POTENTIOMETER) WINDOW
ERROR CODE
ERROR CODE
~E:':~ .OV
r-~~'--l.500V MAX.
WORKING RANGE
P--cr-o~-:oI4. 5V MAX.
E 26
T
MP 8 VOLTAGES +90· ANGLE MIN. SIG. = +500mV (.SODY)
a" ANGLE :::: +2.S0V
-90· ANGLE MAX. SIG. = +4.S0V
NOTE: ALL VOLTAGES ARE MEASURED WITH REFERENCE TO GND (TERMINAL Xl-12 OR MP15)
ON MAIN BOARD
C D-3~-5.0V
Xl
-#-WIRE NUMBER
Xl --D-- CENTAL UNIT
TERMINAL BOARD
-0- TEST POINT ON MAIN BOARD
4.0 LINERIDER SETTINGS AND ADJUSTMENTS
4.1 GENERAL INFORMATIONCalibration of a linerider will require the hoist rope line pull information, which should beprovided by the manufacturer. Use single part line when calibrating the linerider.Lineriders require specific wire rope size, see Table 2 to insure your rope size matchesyour linerider provided.
NOTE: A new wire rope is normally over sized, the amount oversize will depend on thediameter of the rope. With normal wear the inter core breaks down and diameterdecreases, See your manufactures guide lines for wire rope replacementconditions.
Table 2. Lineriders should match the wire diameter of your hoist rope.
ITEM NUMBER DESCRIPTION WITH WIRE ROPE SIZEWIRE ROPEDIAMETER
ADVISED RANGE048-500-060-005 SENSOR, LINERIDER SKM500 7/8" ±3/64
048-500-060-006 SENSOR, LINERIDER SKM500 1" ±3/64
048-500-060-012 SENSOR, LINERIDER SKM500 1-1/8 2 TON KMD ±3/64
048-500-060-013 SENSOR, LINERIDER SKM500 1-1/4 2 TON KMD ±1/16
The linerider requires a load sheave adjustment to maximize the voltage output of theamplifier and minimize the line angle through the linerider. The linerider maximumoutput of 2.5 volts should be equal to the maximum hoist rope line pull. The load sheavemay need to be adjusted by turning the eccentric wheel on the load sheave of theSKM500 linerider, see figure below.
P
L o ad S h eav e
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 10
301-371-6126
4.1 LINERIDER ZERO POINT ADJUSTMENT
NOTE: Complete the following processes before placing cable through the linerider.
ZERO POINT SETTINGS
a.) Check that the differential output of the main and auxiliary linerider is within±25millivolts at zero force:
• Main Linerider: central unit terminal connection X1-#33 and X1-#34.• Auxiliary linerider: central unit terminal connection X1-#23 and X1-#24.
b.) Adjust the linerider voltages on the main board, Refer to Figure 2 below.
SYSTEM EPROM
CPUX7
BR-3
DATA EPROM
MEMORY
RAM
X2
MP-11
X3
P3MP-3 MP-4
MP-18
MP-12
+.500
X4
MP-13
MP-2
X1
P5P4MP-5
3 2
MP-6MP-7
X6
1
MP-9MP-8
MP-15MP-19
MP-1
Figure 2. Main Board
• Adjust the main linerider zero point by placing your positive volt meter lead onMP 3 (measuring point 3) with your ground lead on MP 11. Turn the screw onpotentiometer P3 so the volt meter reads a value of 0.500 volts.
• Adjust the auxiliary linerider by placing your positive volt meter lead on MP 5 withyour ground lead on MP 11. Turn the screw on potentiometer P5 so the voltmeter reads a value of 0.500 volts.
• After completing this adjustment run the hoist rope through the lineriders.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 11
301-371-6126
4.2 LINERIDER OUTPUT ADJUSTMENT
LINERIDER OUTPUT ADJUSTMENTS
a) Calculate the output voltage required from the linerider using the known thetotal load and maximum line pull information. The tolerance for the outputvoltage “X” is +0.0, -0.2 volts.
NOTE: The total load includes the load, rigging, cables, and hook block. Testload should be 80% of maximum rated load for the cranes configurationor condition. To comply with the SAE J376 standards the test load mustbe to a known accuracy of ±1%.
TEST LOAD x 2.5 = ÷ PARTS OF LINE = X LINE PULL
23.600 x 2.5 = 2.0 ÷ 1 = 2.0 29.500
“X” is equal to the to optimum output voltage of the linerider. The outputvoltage required in this example is 1.8 to 2.0 volts.
WARNING: THE OPERATOR IS RESPONSIBLE FOR OPERATING THE CRANEWITHIN THE MANUFACTURE’S SPECIFIED PARAMETERS.
b) Pick the test load used in the calculation for the output voltage with a singlepart of line.
c) Take a voltage reading with a voltmeter and compare the reading with the
calculated voltage and decide if a mechanical adjustment of the linerider isneeded.
• Main Linerider: central unit terminal connection X1-#33 and X1-#34.• Auxiliary linerider: central unit terminal connection X1-#23 and X1-#24.
d) If a mechanical adjustment is necessary follow steps below, if no mechanical
adjustment is necessary proceed to next Section and begin calibration. • Before and after you set the mechanical adjustment, scribe a line on the
side of the eccentric wheel to show the amount of change.• Loosen the adjustment nut, see Figure 3. Note that there is a single lockout
nut on one side and a double on the other. These both should be loosenedto some degree. Adjustment from the double nut side seems to work thebest after tightening the 2 nuts together.
• Depending upon the output voltage you can look at the eccentric nut fromthe side of the linerider and determine the direction you should turn.Increasing the height of the load sheave will increase the output voltage.
• Tighten all lock nuts insuring not to move the wheel. e) Return and repeat step ‘c’.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 12
301-371-6126
4.3 LINERIDER CIRCUIT (MAIN LINERIDER)
DRAWING # - LKB24-01
DRAWING # - LKB24-02
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 13
301-371-6126
4.4 LINERIDER CANNON CONNECTION LINERIDER CANNON CONNECTION
The supply voltage can be checked directly at the cannon connection. Using adigital volt meter measure between pins A and B, (A= + 9v) + (B= - 9v) = 18volts. Ifthis voltage is not correct refer to the system wiring diagram and verify all cableconnections. You may need to start at the main board and check the supply voltages attheir proper measuring points.
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 14
301-371-6126
5.0 DIGITAL INPUTS
DRAWING # - LKB36-01
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 15
301-371-6126
9 I
HOIST SELECT
9 I
RIGGING MODE
9 I
AREA DEFINITION
DIGITAL INPUTS
TYPICAL USE AND HOOK-UP
GND
44
43
42
t-------...12V (UB)
D1-2 = DIGITAL INPUT #3 ,-------1
~ I COMPUTER CTO ~ I
L _______ J
D1-1 = DIGITAL INPUT #2 '-----c TO ~ I COMPUTER ~ I
L _______ J
D1-0 = DIGITAL INPUT #1 '-----c TO I ~ I COMPUTER I ~ I
L _______ J
6.0 ANTI-TWO BLOCK CIRCUIT
7.0 BOOM BASE CABLE REEL DIAGRAM
DRAWING # - 031-300-100-424
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 16
301-371-6126
8.0 MAIN BOOM / JUNCTION BOX DIAGRAMS
MAIN BOOM NOSEDRAWING # - 031-300-100-446
JIB NOSEDRAWING # - 031-300-100-522
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 17
301-371-6126
9.0 LUFFING ATTACHMENT / JUNCTION BOX DIAGRAMS
LUFFING LIMIT BASEDRAWING # - 031-300-100-679
LUFFING JIB NOSEDRAWING # - 031-300-100-535
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 18
301-371-6126
10.0 SYSTEM ( 24 VOLT ) DIAGRAM
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 19
301-371-6126
LUFF
ER
LU
FFE
R
AN
GLE
S
EN
SO
R
LIM
IT
SW
ITC
H
I II
I l
MA
IN
BO
OM
TI
P
JUN
CT
ION
B
OX
0
31
-30
0-1
00
-44
6
LUFF
ING
JI
B
CO
NN
EC
TIO
N
CA
BLE
A
SS
EM
BLY
(2
9')
0
31
-30
0-1
00
-41
5
,--. H
---,
,--, )-0
---,
CE
NTR
AL
UN
IT
03
1-3
00
-10
1-1
50
33
+
SIG
----
j!7
CA
BLE
A
SS
EM
BLY
(1
2')
03
1-3
00
-10
0-4
17
~
<c'
<c'
<co
<co
<c'
<c'
;J B
YP
AS
S
PLU
G
03
1-3
00
-10
0-4
44
,--
>-0
---,
,--
)->
---,
~~ -'
" -1
\,,,
'"'''1
3
1
-9Y
31
+9Y
'---
I~~ ,->
,->
::t*
. "'
~-7
E
5
~'--
~~
,I.-
<~
"fB-{E
-1, .,
1,"
",
USE
D
'---
'---
-
9 m
2N
D
Ln
] m
nn
A2B
[!B
Y
AU
XIL
IAR
Y
LlN
ER
IDE
R
.. U
BY
PA
SS
P
LUG
2
ij
031
-30
0-1
00
-53
2
MA
IN
A2B
(1
2')
03
1-3
00
-10
0-5
07
SK
M5
00
(1
")
LlN
ER
IDE
R
04
8-5
00
-06
0-0
06
o
A-{
E-.
o 8
-{ E
-B
c-{
E-c
MA
IN
LlN
ER
IDE
R
o
[~ ~E-o ~~ C
ON
SO
LE
03
1-3
00
-10
0-5
02
~
1112
,
1 o ~Uio
-\
'
" "
GN
D
2 2
~~;t7
GA
8LE
REE
L
1 0
31
-30
0-1
00
-42
4 (3
~5c'
I'l'
---_
_ ,
>-A
-I
l--A
---;:')-A
-l
>-8
-2
2
--8
---;:')-8
-2
>-C
-3
3
--C
---;:')
-C
-3
>
-0
-4
A
--O
---;:')
-D
-A
>-E
-5
5 --
E --7
)-E
-
5 >
-F
-6
6 --
F --
-;:'
)-F
_
6
>-C
-7
7
--C
---;:')
-C
-7
>
-H
-6
S
--H
--7
)-H
-S
>-.
--.
'--J---;:')-J-9
>
-.--
10
'0 _
_ K
---
;:')
-K _
'0
>-L
-1
1
,,--
L --
-;:'
)-l -"
>-M
-'2
1
2--
M -
-7
)-M
-1
2
>-N
-1
3
13 _
_ N
---
;:')
-N _
13
>
-P
-IS
IS
__
P---;:
')-p
_1
5
NC
14
'A
NC
N
r u
,--
H---'
,--
H---'
,--
>-0
---'
,--
>-"---,
,--
>-.-
--,
>0 --
>-< -
-->
0
39
A
18
GH
D
40
A
28
SIG
NA
L 2
3
+S
IG--
-f\,
2
4
_SIG
----
j!7F
3 (A
UX
)
,,--
H---"~~~~~~~f12 -
AG
ND
,,
--,
>-'
---'
2
13 -
-SIG
---{
»L
UF
F
AN
GLE
>
0--
>-'
---1
3
14
--5
Y
,,--
H---1
4
30
-
GN
D
'4N
C
L---,
_
20
-
GN
D
I_L
_____ ~
6
----
&::
+2
4V
l 2
AM
P'
----
-<!l
+24
V
J C~
: =;
~;~g--
-t8L2
.0--
-7 >
-A
---
1 3
5
----
ol+
24
V
8--
7 >
-8
---
2 3B
-
:?~D
C
---7
>-C
---
3 3
7
----
-::' ~X
O 0-
--7 >
-0
---
4 3
6
------
:;.' R
XD
E--7
>-E
---,
CA
BLE
A
SS
EM
BLY
(1
1')
0
31
-30
0-0
60
-05
5
F--
7 >
-F
---
6 4
4
------
7 D
I 2
WIN
CH
S
ELE
CT
I
O~)J
>-O_
'
.1.9
0' ".
c---
l." +-
--.,"
~
~29+--
_S
IG-V
/F2
-SIG
---{
»L
l
>-,
----
, ~~
~~~~
~t
AG
ND
_ U~-_
_ ,>
-8
---2
-S
IG--
-{»
AH
GL
E
C--
-7)-
C
3 3
c ---7
>-C
----3
-5
Y
0--
7)-
"
IS
0 --7
>-D
----IS
G
ND
~ __
____
__ ,
01
GN
D
, G
HO
~-~f
·:
~'~~
CA
BLE
A
SS
EM
BLY
(3
0')
0
31
-30
0-1
01
-15
2
+2
4Y
+2+Y
PO
WER
1
.0--
< ~A-
, H' "
GROU
NO
2 B
--<
~B-
2 6
49
~~~E~W
ITCH
[ ~
:~ ~:=
~ :
41
l8 ,
52
0
5 ~--< ~~_ ~
3 LB
13
61
6 F
--<
~F-
6 2
ARE.O
. D
EriN
ITIO
N
7 ,,
--<
~"-7
1 +
24
Y
X1
03
1-3
00
-10
1-1
52
(3
0')
.,,,~:1 ,
OIR
KE
Y I
hO
3 3
II
I ..
-
R,O
4 4~
i 2
"/8
(:
l)R
ED
~
1 ,"
3 (1
) U
RN
_
__
DI 2
_ 6
1
2 4
I (2
) O
RG
i jc
4
~....!
__
~_J
10.1 VERTICAL CONSOLE DIAGRAM
DRAWING # - 031-300-100-502
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 20
301-371-6126
~
~ '" en
m " " ~
en
w
~ P
AT
os
35
0
©
IlJl
l BBB
B rT
.& '
" In
] h
l
, BB
cd
BBBB
BBBB
BBBB
B BB
BB
6 ~
El ElH
El tiTI
-El E
loElE
ilil il
1lllB
B B
A
ElEl
HEl IWA
RNIN~I
~
p,/;
:~!'
2km,
'o'l
,~~
TEST
S 1
10
I o~
@ 0
[ o~
o~ o~
oW @
o
0
FR
ON
T @
REAR
[~]~II~IBII]I]IIBII
I'i!
<:;l
en :; en ~
• o
" ~ o
I IT
EM
1 2 1\
I P
AR
T N
UM
BE
R I
05
0
35
0
06
1
22
5
03
1
30
0
06
0
05
5
DE
SC
RIP
TIO
N
CO
NS
OLE
, D
S3
50
G,
24
V,
AE
G,
4 D
EC
AD
E
SW
. (L
iNK
BE
LT
LA
TT
ICE
C
RA
NE
) C
AB
LE
AS
SY
, 1
1'
7CO
ND
W
! 7
PIN
P
LUG
IAIB
lclDI
Elclc
l ill"
ll
I O
TY
1 1
Cm
JSD
LE
B
OA
RIl
4 f 4-
" R
EA
R
" en m
Ltd
cR
mn
l .__
___mJ
;~ 3 c~
2 =
=
1
RE
AR
4 ~
2
B
4 C
IT[]
W
IRIN
G
DIA
GR
AM
,~II
.i
~
c+
11.0 SYSTEM ( 12 VOLT ) DIAGRAM
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 21
301-371-6126
LUFF
ER
LU
FFE
R
AN
GLE
S
EN
SO
R
LIM
IT
SW
ITC
H
Innlln~
MA
IN
BO
OM
TI
P
JUN
CT
ION
B
OX
0
31
-30
0-1
00
-44
6
CA
BLE
A
SS
EM
BLY
(3
4')
0
31
-30
0-1
00
-54
0
CE
NT
RA
L U
NIT
0
24
-35
0-1
01
-15
1
CA
BLE
A
SS
EM
BLY
(1
2')
03
1-3
00
-10
0-4
17
IJ,~ '~~
a-7
'2
C-7
".
;:
~:
'-=
'~
'----
--'--
-' "-
--,
, 2.
A-
< ,_
, ,-<
<-
L£
-
2 l
3
-,
~
" "
:If
~L ~
': "
15
: 16
2N
D A2
BLHJ
LU~UJ
[ i 1]
AU
XIL
IAR
Y
LlN
ER
IDE
R
, ,
~
BY
PA
SS
P
LUG
0
31
-30
0-1
00
-53
2
MA
IN
A2B
(1
2')
03
1-3
00
-10
0-5
07
----
SK
M5
00
(1
-1/8
")
LlN
ER
IOE
R
-2
TON
04
8-5
00
-06
0-0
12
o M
AIN
Ll
NE
RIO
ER
c-<
f-3
jo-
<f-o
"
:~:::'
~:1
'---
-'--
-
CO
NS
OLE
0
31
-30
0-1
00
-53
9
I I
"EA
" ~o
CO
M I
I
WIN
CH
.~
:_S~
L~~~
R~~1
__
J a
iR
KEY
o +~~~
flE~
l ~ h
D
3 "
R,D
4
"'-(2
)O
RG
---'
(1)
BR
N_
DI
2 _
_ •
(3
)R
ED
----
A--
---;
' )-
A
8---
--;'
)-8
c---
--;'
)-C
0-
----
;' )-0
E--
---;
' )-E
~-
----
;. )-~
0---
--;' )-"
LUF
FIN
G
JIB
C
ON
NE
CT
ION
S
'f-A
f-
' f-
o f-
' f-
' f-
'
:J B
YP
AS
S
PLU
G
03
1-3
00
-10
0-4
44
CA
BLE
R
EE
L f--~;77
I 0
31
-30
0-1
00
-42
4 (3
2~'~
,) _
__
~
/)-~-1
I--~-?>-A-I
)-0
-2
2
--0
---7
>-8
-2
)-C
-3
3
--C
-?>
-C
-3
)-D
-4
4
--D
---7
>-D
-4
)-E
-5
5
--E
---7
>-E
-5
)-F
-6
6
--F
---7
>-F
-6
)-G
-7
7
--G
---7
>-G
-7
)-H
-B
B
--H
---7
>-H
-B
>-,--,
'--J---7
>-J-9
>
-'-
-1
0
10 _
_
K -
--7
>-K
-1
0
)-L
-ll
11 _
_
L --
-7>
-L _
11
)-M
-1
Z
12 _
_
M -
--7
>-t.
l-1
2
)-N
-1
3
13 _
_
N -
--7
>-N
-1
3
)-P
-IS
IS
--p
---7
>-p
-IS
H
C1
4
14
HC
N
CU
~--------~, ~
'--A
7)-A
---'
,--
87
)-0
---'
• --
c 7
)-C
---'
,--
D 7
)-D
---'
,--
E7
)-E
---'
,--
F7
)-F
---'
,--
G 7
)-G
---'
,--
H7)-H
---'
,--
J7
)-J---'
00
--
K 7
)-K
---O
O
C:-;;-t
-"'-1
\,,,
,,""
33
+
SIG
---j
,!7
32
-9
V
31
+9V
3
9
A2B
G
ND
4
0
A28
SI
GN
AL
23
+
SIG
---I
\'F
3
(AU
X)
24
-S
IG--
-j,!
7
,,--
L 7)-
L---
"~~~
~~~~
iI2
AG
ND
,,--
M 7
)-M
---1
2
13
-S
IG--
-!»
WF
F A
NG
LE
,,--
N 7
)-N
---1
3
14
-5
V
,,--
p 7
)-P
---1
4
30
G
ND
UN
C
I~
_2
0
GN
D
j---
I +
12V
J-' ''':
"" A
---;
' )-
A _
__
_ ,
"
8---
;' )-8
__
__
,
" c-
--;'
)-c _
__
_ ,
"
0---
;' )-0
__
__
,
" E
---;
' )-
E _
__
_ 5
+
12
V
CA
BLE
A
SS
EM
BLY
(1
4')
~)-F----6
44
DI
2
WIN
CH
SELE
CT
~ __
__
__
__
__
_
O_3
_' --3-0
-0---'-O-O
---5-4-'-C
-A-B~LE A
55
EM
':Y
:2:)
J>-O--
--' ;;
~::;;:
: ''''
03
1-3
00
-10
1-1
55
18
-S
IG--
-{>
7L1
A-7
>-A
1
1 A
-7
>-A
----l
15
A
GN
D
9-7
>-8
8
-7
>-8
----2
1
7
-SIG
---!
»AN
GL
E
c-7
>-c
c -7
>-c----3
1
9
-5V
0"
"L
OT
"-7
>-0
1
5
GN
D
AN
GLE
12
V
WG
203
AN
GLE
S
EN
SO
R
10
AM
P!
+
48
t-< A28
RE
LAY
41
DI
GN
D
'"
"
~-.. "
~-1F
CA
BLE
A
SS
EM
BLY
(2
0B
) C
AB
LE
AS
SE
MB
LY
(3")
" 0
31
-30
0-0
60
-00
7
03
1-3
00
-06
0-0
08
+12V
PO
WER
1
_
GR
OU
ND
2
_
.-~~
~~E~
ITCH
[ 4-
+-
L8
,,5
20
5
_
LB #
36
16
_
~REA DEFIHITIO~
7
[i§A--
< <
:;-A
A
--<
<:;
-A-
I -
2 a-
-< <
:;-0
0--
< <
:;-0
-2
_
3 c--
< <
:;-C
C--
< <
:;-C
-3
_
4 --
+--0
--<
<:;-0
D
--<
<:;
-0-
4_
':
j:~-
-<<:
;-~
~--<<:;-~_5_
6 ,.
--<
<:;-
,. ,.
--<
<:;-~-
6-
c--
< <
:;-c
C--
< <
:;-C
-7
_
, "
~i~-~'O~
'~CO~'~'
~'C~'~'O
~~'~'~~~
~~~"====
,-X
l
11.1 HORIZONTAL CONSOLE DIAGRAM
DRAWING # - 031-300-100-539
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 22
301-371-6126
I A I B
I c I D
E
lF I G
I I
ITE
M
I P
AR
T N
UM
BE
R I
D
ES
CR
IPT
ION
I
QTY
1 I
j 1
05
0
35
0
061
229
CO
NS
OLE
, O
S35
0,
24V
, AE
G,
4 D
ECAD
E SW
. 1
i 1
2 03
1 3
00
1
00
0
22
C
ON
NE
CT
OR
, C
AN
NO
N
7 P
IN
RE
CP
T
#1
6
1 3
031
30
0
10
0
17
3
CO
NN
EC
TO
R
AC
ey,
GA
SK
ET
, S
HE
LL
#
16
1
cm~SDLE
BO
AR
D
I 4
031
30
0
10
0
17
4
SC
RE
W,
#4
4
0
X
1/2
" P
HIL
LIP
S
HE
AD
4
14 3 [
1-
5 03
1 3
00
1
00
1
75
W
AS
HE
R,
LOC
K,
#4
4
6 03
1 3
00
1
00
1
76
N
UT,
#
4
40
H
EX
4
2 11
I F
Rm
n
2 7
' 0
00
31
1 0
23
1
14
LA
MP
, 1
4V
, LU
MIT
AS
4
3 3
0"'
1,1~
~I
l 8
' 0
00
-31
1-0
23
-12
8
LAM
P,
28Y
, LU
MIT
AS
-4
2 ~
~
2 0"
' 9
' 0
50
3
50
1
10
1
16
S
TRA
IN
RE
LIE
F A
SS
Y,
PG
13
.5
RE
OjW
HT
1
4 RE
AR
FR
mn
1
0
031
30
0
10
0
35
3
DE
CA
L,
WA
RN
ING
FO
R
CO
NS
OLE
1
B
C
w
WIR
ING
DI,~GR.~M
,-
t ~ J o
PA
T o
s 3
50
0
0 1 [J~
FR
om
Ilill
BB
BB
1
6 &
'"
R
c:
:J
II ~[~
I~IE
II[W
JII(
(@))
11
@
' BB
~ BB
BBBB
BBBB
BBB
BBBB
i[f
i """
e Hl [l
ElEl
i[fi
-El El
HEl
' ~
a 0
r A
El E
lHEl
a"a'
BB
BB
BB
CQ
) I
tl~ tl~
tl~ Bl~ I
CQ
) I WA
RNIN
~I
0 0
ALW
AY
S P
"'F
aRM
PR
E-orgg
'ONAL
\
0 o
0
~ 1
0
~
"' r., CD
Q;
0
o
lr-
o 2,3
,4,5
,6
CO
NN
EC
TOR
H
AS
S
AM
E
LOC.
A. T
ION
A
S
EX
ISTI
NG
S
TRA
IN
RE
LIE
F.
12.0 TERMINAL BOARD DESIGNATION
TERMINAL BOARDDRAWING # - 024-350-060-739
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 23
301-371-6126
r-----------------------------------------------, P'
E 29
74 30 73
"')-y"'2" ~" I
31 72 p e, 38 71 '" 39 70
" ')-1"' " 40
69 co e, " 33 68 '" 34 67 R6 )-y~K5 ~Y9 35 66 F5 e5 36 65 '" 37 64
R6 ')-1"' " ~" 32
63 F< e7
62 '" 61 Rl0')-~-c§3 ,+V5 60 " e9
59 " 58 R12-t-1-E: K2 'S/-V2 57 " en 5
56 " 10
o
55 R14'1-
11 54 " m i-Ef:JK1 '+ V1 7 53 '" 8
VERLOAD ~ 52 R16'1- ~~8 ~V8 9
51 F8 m I
6 50 '" 12
A2B ~ 49 R1B)-~¢K9 16 48 " en Y9 1 ~ I--- M2A 2 ~~ -~I--- " , CONNECTION 80ARD 43 024 350 300 175 " , 42 DE-1 41 DE GND 40 ~:~ -fk---ll ~~~PARATOR 39 38 -08 37
'" 36 '" 35 .cs
34 5'" 33 +SIG KMD-1
32 9Y 31 .9V 30
9 S'" W6 8 '"
_ NOT USED
7 -9V 6 '"v 5 4 s'" 3 +SIG _KMD 2
2 9Y rB = ~~u 21 '"v 2X SERIAL ~~ 0 INTERFACE ~~
19 .. Zo -5Y ~~
18 '" NOT USED o~
17 Z
'" ANGLE MAIN BOOM r-16 OND 15 14 5Y .£ rE 13 '" ANGLE JIB 12
'" ~ 11 10 5Y 9 '" NOT USED 8
'" - r- ~~u 7
~ 6 Z~
.o!. p.! ~c
5 ~ ~
-U8....-.c 4 I
4 -UB I'--( 3
1 3 :c-'IIl-c ~
+UB I'--( 2 2 ~ +U81'--( 1 ~ rL >-"fl--c r-1-
rxr - r- MAIN 80ARD 024-350-300-161 L _______________________________________________ ~
13.0 MAIN BOARD MEASURING POINTS
MEASURING POINT LAYOUTDRAWING # - 024-350-300-081
Service Manual - 1225/1229 Console DS350 Rated Capacity Limiter System
SkyAzúl, Equipment Solutions www.skyazul.com Page 24
301-371-6126
~ MEMORY EXT. eI X4
MP-13
~ RAM -BR-21E]
@
@
BR-3 1E1 BR-4 0
~ DATA EPROM
MP-22 -
• SYSTEM
! ~CPU
8 BR - 1
DDDDDD
EPROM
12 VOLT SYSTEM BR-7, 8, & 9 INSTALLED 24 VOLT SYSTEM 8R-7, 8, & 9 REMOVED
MP-11 -MP-10 -
@ @
~ @-mJ@
hi X6
!~I~I~I~I I "<t LO <.0 '"
D-- I I I I ::E D-- a... 0... a..
::E :::2:: :::2:: :::2::
X3 5 I iE~ ~ ~ D D D D "I §~~X~2 ~~5"ll1 ~ L--'I §~~~~
MP TEST POINTS MP- = +5V MP-11 = MP- 2 = -5V MP-12 = MP- 3 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-13 = MP- 4 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-14 = MP- 5 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-15 = MP- 6 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-16 = MP- 7 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-17 = MP- 8 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-18 = MP- 9 = ANALOG MEASURING CHANNEL REFERENCE SOFTWARE MP-19 = MP-9/1 = COMPUTER GND MP-20 = MP-9/2 = CRANE GND MP-21 = MP-10 = +3V REFERENCE VOLTAGE
_MP-9!2
_MP-9!1
XI
_ MP-20
_ MP-21
_MP-1
_ MP-19
_ MP-16
_ MP-15
_ MP-14
_ MP-17
ffiHID GROUND
+5V
DIGITAL GROUND +9V ANALOG GROUND -9V
+5V +5V
-5V
OPERATING VOLTAGE
INPUT VOLTAGE
SkyAzúl, Soluciones de Equipos www.skyazul.com 301-371-6126
SkyAzúl, Equipment Solutions www.skyazul.com 301-371-6126
SkyAzúl, Inc. 16 Walnut Street Middletown, MD 21769 Phone 301-371-6126 Fax 301-371-0029 [email protected] www.skyazul.com