Carlisle RPP ™ Panther ® with ULTRA-CORD ™ Synchronous Drive Systems Drive Design Manual www.cptbelts.com Power Transmission Products, Inc.
Carlisle RPP™ Panther® with ULTRA-CORD™
Synchronous Drive Systems
Drive Design Manual
www.cptbelts.com
Power Transmission Products, Inc.
2
SAFETY NOTE � WARNING!FAILURE TO FOLLOW RECOMMENDED APPLICATION INFORMATION AND RECOMMENDEDPROCEDURES FOR INSTALLATION, CARE, MAINTENANCE AND STORAGE OF PRODUCTS MAYRESULT IN FAILURE TO PERFORM PROPERLY AND MAY RESULT IN DAMAGE TO PROPERTYAND SERIOUS BODILY INJURY. MAKE SURE THAT PRODUCT SELECTED FOR ANY APPLICA-TION IS RECOMMENDED FOR THAT SERVICE.
APPLICATION INFORMATION IS GIVEN WITH THE PRODUCTS LISTED IN THIS CATALOG. REFERTO THE SAFETY & TECHNICAL DATA SECTIONS OF THIS CATALOG FOR INFORMATIONREGARDING SAFETY, CARE MAINTENANCE AND STORAGE OR CONTACT CARLISLE POWERTRANSMISSION OR YOUR CARLISLE POWER TRANSMISSION DISTRIBUTOR FOR ASSISTANCEOR SPECIFIC RECOMMENDATIONS.
3
RPPTM PANTHER® ULTRA-CORD™ BELT PROFILE . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . . . . . .4
RPPTM PANTHER® ULTRA-CORD™ BELT FEATURES . . . . . . . . . . . . . . . . . . . . . . .Pg. . . . .5-6
RPPTM PANTHER® ULTRA-CORD™ BELT CONSTRUCTION . . . . . . . . . . . . . . . . . . .Pg. . . . . . .7
RPPTM PANTHER® ULTRA-CORD™ BELT NOMENCLATURE . . . . . . . . . . . . . . . . . .Pg. . . . . . .8
RPPTM PANTHER® ULTRA-CORD™ BELT STANDARD SIZES . . . . . . . . . . . . . . . . . .Pg. . . . . . .9
RPPTM PANTHER® ULTRA-CORD™ BELT TOLERANCES . . . . . . . . . . . . . . . . . . . . .Pg. . .10, 66
RPPTM PANTHER® SPROCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . .11-15
RPPTM PANTHER® BUSHINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . .16-21
RPPTM PANTHER® SPROCKET TOLERANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . . . . .66
RPPTM PANTHER® SPROCKET BALANCING STANDARDS . . . . . . . . . . . . . . . . . . . .Pg. . . . . .22
RPPTM PANTHER® ULTRA-CORD™ BELT DRIVE SELECTION PROCEDURE . . . . . .Pg. . .23-30
RPPTM PANTHER® ULTRA-CORD™ BELT INSTALLATION AND TENSIONING . . . . .Pg. . .31-36
RPPTM PANTHER® ULTRA-CORD™ BELT HORSEPOWER TABLES . . . . . . . . . . . . .Pg. . .37-45
CENTER DISTANCE SELECTION TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . .46-63
TROUBLE SHOOTING GUIDE FOR SYNCHRONOUS DRIVES . . . . . . . . . . . . . . . . .Pg. . . . . .64
ENGINEERING DATA Belt installation & Tensioning Allowances
Belt Tolerance
Sprocket Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . . 66-67
DRIVE ASSISTANCE DATA SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pg. . . . . .68
RPPTM and Panther® ULTRA-CORD™ are Trademarks of Carlisle Power Transmission Products, Inc.
RPPTM PANTHER® ULTRA-CORD™
BELT DRIVE SYSTEMSDesign Manual Index
4
RPP BELT PROFILE
RPP PANTHER ULTRA-CORD belts have the proven reinforced parabolic profile. The RPP beltprofile is illustrated in Figure 1. The RPP belt profile, a deeper and more efficient belt toothdesign, enables the belt to transmit more power, while occupying less space.
The reinforced parabolic profile of the RPP PANTHER ULTRA-CORD belt has an angle whichincreases from the base to the top of the tooth. This increasing angle enables a deeper toothdesign.
The reinforced parabolic profile in conjunction with the increased tooth depth results in the following advantages:
• A substantial reduction in noise compared to standard profile and similar curvilineartooth designs, and an even greater reduction when compared to chain and other mechanical drive systems.
• An improvement in tooth jump resistance.
• An increase of torque and power transmission capability.
• Higher resistance to tooth shear.
• Improved belt and sprocket meshing.
Figure 1
RPP PANTHER ULTRA-CORD Belt Profile
5
RPP PANTHER ULTRA-CORD Belt Features
RPP PANTHER ULTRA -CORD belts are particularly recommended for efficient, compact drives whichexperience high torque loading.
RPP PANTHER BELT FEATURES
• Wide range of sizes in 8mm and 14mm pitches. (See Table 1 - Page 9)
• Highest horsepower ratings of any rubber synchronous belt in the industry.
• More compact drives.
• Reduced noise. (See Figure 2 - below)
• No lubrication or maintenance as required for chain drives.
• Allows the use of idlers on the backside of the belt unlike competing polyurethane systems.
• Precision ground backside for reduced vibration.
NOISE COMPARISONRPP Panther vs COMPETITIVE SYSTEM*
RPM @ DRIVER SPROCKET8mm Belt - 20mm Wide - Two 44 Tooth Pulleys - Tension = 100 LBS./Strand
Figure 2
Because the RPP PANTHER ULTRA-CORD retains the already proven RPP belt profile (recognized as the quietest system on the market), it possesses all the known advantages of low noise of the RPP belt profile. Inaddition to this it has the extra advantages of:
• Further reduction of noise by reduced belt widths due to the higher performance rating of the system.
• Low noise characteristics compared to drive systems using polyurethane, steel etc. due to the rubber construction.
• Use of smaller diameter sprockets create lower belt speeds and thereby less noise.
6
RPP PANTHER ULTRA-CORD Belt Features
The new RPP PANTHER ULTRA-CORD Belt achieves a level of performance previously possible only withmechanical drive systems (chain, gears, line shafts etc.) which contain inherent disadvantages of weight, noise,cost and maintenance. RPP PANTHER ULTRA-CORD Belt enters the market with physical characteristics that yieldoutstanding versatility unavailable in other belt drives or mechanical systems.
The RPP PANTHER Drive System (belt and sprockets) can supply up to 125% more horsepower than RPP PlusBelts, providing the most complete product line in the industry. This data is presented graphically in Figure 3 above.
Because of the positive engagement and high flexibility of RPP PANTHER ULTRA-CORD Belts, high levels of effi-ciency are obtained. A well designed and installed RPP PANTHER system will be 98% efficient and will retain thisefficiency with minimal maintenance. Chain and V-belt drives possess inherent inefficiencies and require a highlevel of maintenance (lubrication and retensioning). Many of these systems are currently in use with efficiencieswell below 95%. This significant increase in efficiency can result in a payback of the initial cost differential within avery short period of time.
COMPARISON CHARTS
200%
150%
100%
50%
0
Synchronous Belt Relative HP Ratingsper mm width8M (40 tooth sprocket @ 1750 rpm)
250%
200%
150%
100%
50%
0
RPP
Plus
,
Goo
dyea
r HPP
T+ G
ates
Pow
er
Grip
GT2
Goo
dyea
r
Whi
teH
awk
Goo
dyea
r
Eagl
e Pd
Orig
inal
Pan
ther
,
Jaso
n Ti
ger
G
oody
ear
Blac
kHaw
k
Pant
her
ULT
RA-C
ORD
14M (32 tooth sprocket @ 1000 rpm)
100
90
80
Relative Energy EfficiencyRPP PANTHER ULTRA-CORD Synchronous BeltsVersus V-belts
93*95*
98*
* U.S. Department of Energy data
Std WrappedV-belts
PremiumCog-belts
RPPPanther
ULTRA-CORD
Figure 3
Panther ULTRA-CORD is capable of exceeding the HP ratingsreferenced in this chart. Contact Carlisle Engineering forfurther information.
7
RPP PANTHER ULTRA-CORD Belt Construction
RPP PANTHER ULTRA-CORD BELT Construction
RPP PANTHER Belt is constructed with materials of the highest quality and strength. Extensive development per-formed by Research & Development has resulted in the homogeneous integration of all components, the cohesivebond of which imparts superior torque capacity giving the RPP PANTHER the ability to exceed the performance ofexisting belt drives and compete with chain and other mechanical systems.
A ULTRA-CORD Tensile MemberB Blended “ICR” Rubber Body-ABLEC Single Cover Nylon FabricD Ground Back
New RPP™ Panther® with ULTRA-CORD™ !
A) The ULTRA-CORD Tensile Member
• Reduced tension decay compared to aramid cord.
• ULTRA-CORD allows for lower installation tensions.
• Improved tensile strength for higher HP ratings.
• ULTRA-CORD doesn’t absorb moisture.
• ULTRA-CORD has improved flex life over aramid cord belts.
B) New RPP™ Panther® with ABLE™ Compound
• New reformulated compound reduces tooth shear.
• Better adhesion to the belt cord and tooth facing.
• More robust compound for improved processing.
C) Nylon Tooth Facing Fabric
• Strong nylon fabric is bonded to the belt surface to improve load carrying capability.
C) Graphite Impregnated Cover
The cover has a special graphite impregnated fabric providing a self-lubricating feature which increases the efficiency of the drive while providing:
• Exceptional resistance to abrasion and tooth shear due to low coefficient of friction.
• Increased drive efficiency.
• Increased belt and sprocket life.
D) Ground Back
• Allows the use of idlers on the backside of the belt unlike competing polyurethane systems.
• Offers consistent thickness and eliminates potential sources of vibration.
Figure 4
8
RPP PANTHER ULTRA-CORD Belt Nomenclature
CLASSIFICATION OF RPP PANTHER ULTRA-CORD BELTS
RPP PANTHER ULTRA-CORD belts are available in 8mm and 14mm pitches.The dimensional parameters for these RPP PANTHER belt pitches are shown in Figure 5.
Figure 5
To obtain a full description of the RPP PANTHER belt the following data is used:
a) Belt Pitch: The distance in millimeters between two adjacent tooth centers as measured along the pitch line of the belt. (See Figure 6)
b) Belt Pitch Length: The total length (circumference) of the belt as measured along the pitch line. (The theoretical pitch line of an RPP PANTHER belt lies at the center of the tensile member.)
c) Belt Width: The width of the belt measured in millimeters.
Figure 6
Tolerances on belt width are shown in Table 4 on page 10.Tolerances on belt thickness are shown in Table 5 on page 10.All RPP PANTHER belts are supplied with ground back to class 2 thickness tolerances.Belts with special controlled thicknesses (ground to class 1 tolerances) are offered forapplications where variations in belt thickness cause problems such as vibration, conveying problems etc...
Standard belt lengths and widths are listed in Tables 2 and 3 on page 9. A typical RPP PANTHER belt designationis detailed below:
2100PTH14M-20
2100 = belt pitch length (mm) 14M = belt pitch (mm)PTH = belt construction and tooth profile (PANTHER) 20 = belt width (mm)
Pitch hs b a r1(mm) (mm) (mm) (˚) (mm)
8 3.20 5.50 32 1.00
14 6.00 9.50 32 1.75
Belt Pitch Line
Pitch
Sprocket Pitch Line
Pitch Diameter
Outside Diameter
9
RPP PANTHER ULTRA-CORD Belt Standard SizesTABLE 2 – RPP PANTHER 8mm PITCH SYNCHRONOUS BELTS
480PTH8M 480 60 0.08 0.14 0.23 0.41 18.90560PTH8M 560 70 0.08 0.18 0.27 0.43 22.05600PTH8M 600 75 0.10 0.19 0.29 0.47 23.62640PTH8M 640 80 0.11 0.20 0.32 0.50 25.20720PTH8M 720 90 0.12 0.22 0.35 0.60 28.35800PTH8M 800 100 0.13 0.24 0.39 0.67 31.50880PTH8M 880 110 0.15 0.28 0.43 0.73 34.65960PTH8M 960 120 0.16 0.30 0.47 0.80 37.80
1040PTH8M 1040 130 0.17 0.32 0.50 0.89 40.941120PTH8M 1120 140 0.19 0.34 0.55 0.94 44.091152PTH8M 1152 144 0.19 0.35 0.56 0.97 45.351200PTH8M 1200 150 0.20 0.37 0.58 1.01 47.241224PTH8M 1224 153 0.21 0.39 0.60 1.02 48.181280PTH8M 1280 160 0.22 0.40 0.62 1.07 50.391440PTH8M 1440 180 0.24 0.44 0.70 1.21 56.691600PTH8M 1600 200 0.27 0.50 0.78 1.33 62.991760PTH8M 1760 220 0.29 0.54 0.85 1.48 69.301800PTH8M 1800 225 0.30 0.55 0.88 1.50 70.862000PTH8M 2000 250 0.34 0.62 0.97 1.67 78.742200PTH8M 2200 275 0.37 0.68 1.07 1.84 86.612400PTH8M 2400 300 0.40 0.74 1.17 2.00 94.482600PTH8M 2600 325 0.44 0.80 1.27 2.17 102.362800PTH8M 2800 350 0.47 0.86 1.37 2.34 110.233048PTH8M 3048 381 0.51 0.94 1.48 2.56 120.003280PTH8M 3280 410 0.55 1.01 1.60 2.75 129.133600PTH8M 3600 450 0.61 1.11 1.76 3.01 141.734400PTH8M 4400 550 0.74 1.35 2.15 3.68 173.23
Length Pitch No. Width Code (mm) PitchCode Length of Length
(mm) Teeth Belt Weight (lb) (inches)
For Complete Part Number, add width code to the length code. Example: 960PTH8M-35
12 22 35 60
TABLE 3 – RPP PANTHER 14mm PITCH SYNCHRONOUS BELTS
966PTH14M 966 69 0.40 0.88 1.36 1.88 2.52 38.031190PTH14M 1190 85 0.48 1.08 1.68 2.33 3.11 46.851400PTH14M 1400 100 0.60 1.27 1.97 2.74 3.65 55.121610PTH14M 1610 115 0.67 1.47 2.27 3.14 4.20 63.391778PTH14M 1778 127 0.74 1.61 2.52 3.47 4.64 70.001890PTH14M 1890 135 0.78 1.72 2.67 3.70 4.93 74.412100PTH14M 2100 150 0.87 1.91 2.97 4.10 5.48 82.682310PTH14M 2310 165 0.96 2.10 3.26 4.51 6.02 90.942450PTH14M 2450 175 1.02 2.24 3.46 4.79 6.40 96.462590PTH14M 2590 185 1.08 2.36 3.66 5.06 6.76 101.972800PTH14M 2800 200 1.17 2.55 3.95 5.47 7.31 110.243150PTH14M 3150 225 1.31 2.87 4.46 6.17 8.21 124.023360PTH14M 3360 240 1.40 3.06 4.75 6.56 8.76 132.283500PTH14M 3500 250 1.46 3.18 4.95 6.92 9.13 137.803850PTH14M 3850 275 1.60 3.50 5.44 7.52 10.04 151.584326PTH14M 4326 309 1.80 3.93 6.11 8.47 11.27 170.324578PTH14M 4578 327 1.90 4.16 6.48 8.95 11.92 180.244956PTH14M 4956 354 2.06 4.50 6.97 9.65 12.86 195.12
Length Pitch No. Width Code (mm) PitchCode Length of Length
(mm) Teeth Belt Weight (lb) (inches)
For Complete Part Number, add width code to the length code. Example: 2100PTH14M-65
20 42 65 90 120
10
RPP PANTHER ULTRA-CORD Belt Tolerances
TABLE 4 – BELT WIDTH TOLERANCES
(mm) 0 to 837mm 838 to 1675mm 1676mm and over
0 to 11.0 +0.5/-0.8 +0.5/-0.8
11.1 to 38.0 +0.8/-0.8 +0.8/-1.3 +0.8/-1.3
38.1 to 50.7 +0.8/-1.3 +1.3/-1.3 +1.3/-1.5
50.8 to 76.2 +1.3/-1.5 +1.5/-1.5 +1.5/-2.0
76.3 to 120.0 +1.5/-2.0 +1.5/-2.0 +2.0/-2.0
BELT WIDTH WIDTH TOLERANCES FOR THE FOLLOWINGRANGE BELT LENGTH RANGES (mm)
(inches) 0 to 33.0 in 33.1 to 66.0 in 66.1 in and over
0 to .44 +.02/-.03 +.02/-.03
.45 to 1.50 +.03/-.03 +.03/-.05 +.03/-.05
1.51 to 2.00 +.03/-.05 +.05/-.05 +.05/-.06
2.01 to 3.00 +.05/-.06 +.06/-.06 +.06/-.08
3.01 to 4.72 +.06/-.08 +.06/-.08 +.08/-.08
BELT WIDTH WIDTH TOLERANCES FOR THE FOLLOWINGRANGE BELT LENGTH RANGES (in)
TABLE 5 – BELT THICKNESS TOLERANCES
RPP
PANTHER 5.40 +/-0.15 +/-0.25 +/-0.60
8mm
RPP
PANTHER 11.10 +/-0.15 +/-0.25 +/-0.60
14mm
BELT NOMINAL TOLERANCES FOR VARIOUSTYPE THICKNESS CONSTRUCTION TYPES (mm)
(mm)
CLASS 1PANTHERCLASS 2
INDUSTRYSTANDARD
RPP
PANTHER .213 +/-.006 +/-.010 +/-.024
8mm
RPP
PANTHER .437 +/-.006 +/-.010 +/-.024
14mm
BELT NOMINAL TOLERANCES FOR VARIOUSTYPE THICKNESS CONSTRUCTION TYPES (in)
(inches)
CLASS 1PANTHERCLASS 2
INDUSTRYSTANDARD
BELT TOLERANCE
Inches Millimeters Up to 33” 33 to 66” Over 66”
7/16 to 1 1/2 11.1 to 38.1 +1/32-1/32 +1/32-3/64 +1/32-3/641 1/2 to 2 38.1 to 50.8 +1/32-3/64 +3/64-3/64 +3/64-1/162 to 2 1/2 50.8 to 63.5 +3/64-3.64 +3/64-1/16 +1/16-1/162 1/2 to 3 63.5 to 76.2 +3/64-1/16 +1/16-1/16 +1/16-5/64
3 to 4 76.2 to 101.6 +1/16-1/16 +1/16-5/64 +5/64-5/644 to 7 101.6 to 177.8 +3/32-3/32 +1/16-5/64 +5/64-5/64Over 7 over 177.8 +3/16-1/4
STOCK BELT WIDTH TOLERANCES
BELT WIDTHS BELT LENGTH (INCHES)
11
RPP PANTHER ULTRA-CORD BELT SPROCKETS
RPP PANTHER ULTRA-CORD SPROCKETS
The RPP sprocket tooth profile has been designed and perfected to be used in conjunction with the RPPPANTHER ULTRA-CORD belt profile. This sprocket profile is mandatory in attaining maximum func-tionality of the drive.
NOTE: RPP PANTHER ULTRA-CORD SYNCHRONOUS BELTS SHOULD ONLY BE USEDWITH RPP PANTHER SPROCKETS.
These sprockets are specifically designed to handle the high loading imposed by the RPP PANTHERULTRA-CORD belts. Extensive testing and market feedback confirms the reliable nature of the RPPPANTHER ULTRA-CORD system.
RPP PANTHER ULTRA-CORD Sprockets are easily identified by their black finish.
Carlisle RPP PANTHER ULTRA-CORD sprockets are constructed from high quality materials, and manufactured under high standards of quality control with particular attention to the tight dimensionaltolerances required. The sprocket teeth are designed to mesh and conform exactly to those of thebelt, resulting in a drive which functions as a precision gear system.
RPP PANTHER ULTRA-CORD SPROCKET NOMENCLATURE
A typical sprocket designation is detailed below:
40PTH14-65FQ
40 = Number of sprocket teethPTH = Tooth profile and construction14 = Tooth pitch in millimeters65 = corresponding belt width in millimetersFQ = Bushing allocation
12
RPP PANTHER ULTRA-CORD BELT SPROCKETS
The figure following the sketch reference letter in the “Type” column indicates the construction of the sprocket.(1 = Solid, 2 = Web, and 3 = Arms), and the letter “F” indicates that the sprocket has flanges.
STOCK SPROCKET DIMENSIONS8mm PITCH, 12mm BELT WIDTH (0.47 in), SPROCKET FACE WIDTH = 21mm (0.83 in)
22PTH8-12 MPB 22 2.206 2.154 2.56 N/A MPB1F 0.62 1.62 1 45 N/A 0.500 1.000 1.924PTH8-12 JA 24 2.406 2.354 2.76 1.34 E1F 0.27 N/A 1.00 0.44 0.500 1.250 0.526PTH8-12 JA 26 2.607 2.554 2.95 1.88 E1F 0.27 N/A 1.00 0.44 0.500 1.250 0.628PTH8-12 QT 28 2.807 2.754 3.15 N/A E1F -0.04 N/A 1.25 0.38 0.500 1.500 0.730PTH8-12 QT 30 3.008 2.955 3. 35 N/A E1F -0.04 N/A 1.25 0.38 0.500 1.500 0.932PTH8-12 QT 32 3.208 3.155 3.54 N/A E1F -0.04 N/A 1.25 0.38 0.500 1.500 1.134PTH8-12 SH 34 3.409 3.356 3.82 N/A D1F 0.50 N/A 1.25 0.08 0.500 1.688 1.236PTH8-12 SH 36 3.609 3.556 3.94 N/A D1F 0.50 N/A 1.25 0.08 0.500 1.688 1.338PTH8-12 SH 38 3.810 3.756 4.13 N/A D1F 0.50 N/A 1.25 0.08 0.500 1.688 1.640PTH8-12 SH 40 4.010 3.956 4.33 N/A D1F 0.50 N/A 1.25 0.08 0.500 1.688 1.944PTH8-12 SDS 44 4.411 4.357 4.76 3.50 C1F 0.48 0.08 1.31 N/A 0.500 2.000 2.1 48PTH8-12 SDS 48 4.812 4.757 5.16 3.80 C1F 0.48 0.08 1.31 N/A 0.500 2.000 2.656PTH8-12 SDS 56 5.614 5.558 5.95 4.60 C1F 0.48 0.08 1.31 N/A 0.500 2.000 3.964PTH8-12 SDS 64 6.416 6.359 6.77 5.40 C1F 0.48 0.08 1.31 N/A 0.500 2.000 5.372PTH8-12 SDS 72 7.218 7.160 7.60 6.20 C2F 0.48 0.08 1.31 N/A 0.500 2.000 5.180PTH8-12 SDS 80 8.020 7.961 8.39 6.90 C2F 0.48 0.08 1.31 N/A 0.500 2.000 6.790PTH8-12 SDS 90 9.023 8.963 7.90 C3 0.48 0.08 1.31 N/A 0.500 2.000 6.3112PTH8-12 SK 112 11.229 11.166 10.00 C3 0.62 N/A 1.88 0.42 0.500 2.625 10.6144PTH8-12 SK 144 14.437 14.370 13.19 C3 0.62 N/A 1.88 0.42 0.500 2.625 18.5192PTH8-12 SF 192 19.249 19.176 18.00 C3 0.62 N/A 2.00 0.54 0.500 2.938 27.5
SPROCKET NO. OF SPROCKET SPROCKET FLANGE SPROCKET SPROCKET DIMENSIONS BORE WT.NUMBER BUSHING TEETH P.D. O.D. O.D. I.D. TYPE (lbs)E K L M MIN MAX
NOTE: WEIGHTS FOR ALL BUSHED ITEMS ARE APPROXIMATE AND DO NOT INCLUDE THE BUSHINGS.
Type AF Type BF Type CF Type DF
Type EF Type MPBF* Type LFBored-To-Suit
Type A Type B Type C Type D
Type E Type MPB Type L
13
SPROCKET NO. OF SPROCKET SPROCKET FLANGE SPROCKET SPROCKET DIMENSIONS BORE WT.NUMBER BUSHING TEETH P.D. O.D. O.D. I.D. TYPE (lbs)MIN MAXE K L M
RPP PANTHER ULTRA-CORD BELT SPROCKETS
STOCK SPROCKET DIMENSIONS8mm PITCH, 22mm BELT WIDTH (0.87 in), SPROCKET FACE WIDTH = 31mm (1.22 in)
8mm PITCH, 35mm BELT WIDTH (1.38 in), SPROCKET FACE WIDTH = 44mm (1.73 in)
8mm PITCH, 60mm BELT WIDTH (2.36 in), SPROCKET FACE WIDTH = 70mm (2.76 in)
NOTE: WEIGHTS FOR ALL BUSHED ITEMS ARE APPROXIMATE AND DO NOT INCLUDE THE BUSHINGS.
22PTH8-22 MPB 22 2.206 2.154 2.56 N/A MPB1F 0.62 1.62 1.84 N/A 0.500 1.000 1.224PTH8-22 JA 24 2.406 2.354 2.76 1.34 E1F 0.66 N/A 1.00 0.44 0.500 1.250 0.726PTH8-22 JA 26 2.607 2.554 2.95 1.88 E1F 0.66 N/A 1.00 0.44 0.500 1.250 0.728PTH8-22 QT 28 2.807 2.754 3.15 1.57 E1F 0.35 N/A 1.25 0.38 0.500 1.500 1.130PTH8-22 QT 30 3.008 2.955 3.35 1.57 E1F 0.35 N/A 1.25 0.38 0.500 1.500 1.332PTH8-22 QT 32 3.208 3.155 3.54 2.56 C1F 0.03 0.35 1.25 N/A 0.500 1.500 1.434PTH8-22 SH 34 3.409 3.356 3.82 2.75 D1F 0.09 0.41 1.25 N/A 0.500 1.688 1.3 36PTH8-22 SH 36 3.609 3.556 3.94 2.81 D1F 0.09 0.41 1.25 0.06 0.500 1.688 1.638PTH8-22 SH 38 3.810 3.756 4.13 3.00 D1F 0.09 0.41 1.25 0.06 0.500 1.688 1.940PTH8-22 SH 40 4.010 3.956 4.33 3.00 D1F 0.09 0.41 1.25 0.06 0.500 1.688 2.344PTH8-22 SDS 44 4.411 4.357 4.76 3.50 C1F 0.09 0.47 1.31 N/A 0.500 2.000 2.548PTH8-22 SDS 48 4.812 4.757 5.16 3.80 C1F 0.09 0.47 1.31 N/A 0.500 2.000 3.256PTH8-22 SDS 56 5.614 5.558 5.95 4.60 C1F 0.09 0.47 1.31 N/A 0.500 2.000 4.564PTH8-22 SDS 64 6.416 6.359 6.77 5.40 C1F 0.09 0.47 1.31 N/A 0.500 2.000 6.172PTH8-22 SDS 72 7.218 7.160 7.60 6.20 D2F 0.12 0.44 1.31 0.03 0.500 2.000 6.080PTH8-22 SDS 80 8.020 7.961 8.39 6.90 D2F 0.12 0.44 1.31 0.03 0.500 2.000 7.890PTH8-22 SDS 90 9.023 8.963 7.90 D3 0.12 0.44 1.31 0.03 0.500 2.000 7.5112PTH8-22 SK 112 11.229 11.166 10.00 C3 0.38 0.25 1.88 0.28 0.500 2.625 12.0144PTH8-22 SK 144 14.437 14.370 13.19 C3 0.38 0.25 1.88 0.28 0.500 2.625 20.7192PTH8-22 SF 192 19.249 19.176 18.00 C3 0.38 0.25 2.00 0.40 0.500 2.938 30.6
22PTH8-35 MPB 22 2.206 2.154 2.56 N/A MPB1F 0.62 1.62 2.35 N/A 0.500 2.000 1.624PTH8-35 MPB 24 2.406 2.354 2.76 N/A MPB1F 0.62 1.81 2.35 N/A 0.500 1.125 2.026PTH8-35 MPB 26 2.607 2.554 2.95 N/A MPB1F 0.62 2.00 2.35 N/A 0.500 1.250 2.428PTH8-35 QT 28 2.807 2.754 3.15 1.57 E1F 0.86 N/A 1.25 0.38 0.500 1.500 1.530PTH8-35 QT 30 3.008 2.955 3.35 1.57 E1F 0.86 N/A 1.25 0.38 0.500 1.500 1.832PTH8-35 QT 32 3.208 3.155 3.54 2.56 A1F 0.25 0.62 1.25 0.48 0.500 1.500 1.634PTH8-35 SH 34 3.409 3.356 3.82 2.75 A1F 0.12 0.62 1.25 0.36 0.500 1.688 1.636PTH8-35 SH 36 3.609 3.556 3.94 2.81 A1F 0.12 0.62 1.25 0.36 0.500 1.688 2.038PTH8-35 SH 38 3.810 3.756 4.13 3.00 A1F 0.12 0.62 1.25 0.36 0.500 1.688 2.340PTH8-35 SH 40 4.010 3.956 4.33 3.00 A1F N/A 0.50 1.25 0.48 0.500 1.688 2.844PTH8-35 SD 44 4.411 4.357 4.76 3.50 D1F 0.31 0.25 1.81 0.23 0.500 2.000 3.848PTH8-35 SD 48 4.812 4.757 5.16 3.80 D1F 0.31 0.25 1.81 0.23 0.500 2.000 4.956PTH8-35 SK 56 5.614 5.558 5.95 4.60 D1F 0.38 0.25 1.88 0 23 0.500 2.625 6.264PTH8-35 SK 64 6.416 6.359 6.77 5.40 D1F 0.38 0.25 1.88 0.23 0.500 2.625 8.872PTH8-35 SK 72 7.218 7.160 7.60 6.20 D1F 0.38 0.25 1.88 0.23 0.500 2.625 11.680PTH8-35 SF 80 8.020 7.961 8.39 6.90 D2F 0.38 0.25 2.00 0.11 0.500 2.938 11.390PTH8-35 SF 90 9.023 8.963 7.90 D2 0.38 0.25 2.00 0.11 0.500 2.938 14.0 112PTH8-35 SF 112 11.229 11.166 10.00 D3 0.38 0.25 2.00 0.11 0.500 2.938 17.2144PTH8-35 E 144 14.437 14.370 13.19 C3 0.77 0.11 2.62 0.12 0.875 3.500 27.5192PTH8-35 E 192 19.249 19.176 18.00 C3 0.77 0.11 2.62 0.12 0.875 3.500 46.2
22PTH8-60 MPB 22 2.206 2.154 2.56 N/A MPB1F 0.62 1.62 3.38 N/A 0.750 1.000 2.324PTH8-60 MPB 24 2.406 2.354 2.76 N/A MPB1F 0.62 1.81 3.38 N/A 0.750 1.125 2.726PTH8-60 MPB 26 2.607 2.554 2.95 N/A MPB1F 0.62 2.00 3.38 N/A 0.750 1.250 3.328PTH8-60 MPB 28 2.807 2.754 3.15 N/A MPB1F 0.62 2.28 3.38 N/A 0.750 1.500 4.030PTH8-60 MPB 30 3.008 2.955 3.35 N/A MPB1F 0.62 2.47 3 38 N/A 0.750 1.625 4.832PTH8-60 MPB 32 3.208 3.155 3.54 N/A MPB1F 0.75 2.69 3.51 N/A 0.750 1.875 5.734PTH8-60 MPB 34 3.409 3.356 3.82 N/A MPB1F 0.75 2.94 3.51 N/A 0.750 2.000 6.636PTH8-60 SKQ 36 3.609 3.556 3.94 2.81 L1F 0.79 N/A 1.25 1.97 0.500 1.938 2.438PTH8-60 SKQ 38 3.810 3.756 4.13 3.00 L1F 0.79 N/A 1.25 1.97 0.500 1.938 3.140PTH8-60 SKQ 40 4.010 3.956 4.33 3.00 L1F 0.79 N/A 1.25 1.97 0.500 1.938 3.844PTH8-60 SFQ 44 4.411 4.357 4.76 3.50 L1F 0.79 N/A 1.25 1.97 0.500 2.375 4.448PTH8-60 SFQ 48 4.812 4.757 5.16 3.80 L1F 0.79 N/A 1.25 1.97 0.500 2.375 6.156PTH8-60 EQ 56 5.614 5.558 5.95 4.60 L1F 0.38 N/A 1.62 2.38 0.875 2.875 8.464PTH-60 SF 64 6.416 6.359 6.77 5.40 A1F 0.12 0.75 2.00 0.02 0.500 2.938 10.272PTH8-60 E 72 7.218 7.160 7.60 6.20 D1F 0.12 1.00 2.62 0.02 0.875 3.500 14.0 80PTH8-60 E 80 8.020 7.961 8.39 6.90 A1F 0.12 1.00 2.62 0.02 0.875 3.500 18.590PTH8-60 E 90 9.023 8.963 7.90 Al 0.12 1.00 2.62 0.02 0.875 3.500 24.5112PTH8-60 F 112 11.229 11.166 10.00 C1 0.74 0.26 3.62 0.12 1.000 4.000 53.3144PTH8-60 F 144 14.437 14.370 13.19 C3 0.74 0.26 3.62 0.12 1.000 4.000 45.3192PTH8-60 F 192 19.249 19.176 18.00 C3 0.74 0.26 3.62 0.12 1.000 4.000 62.0
14
SPROCKET NO. OF SPROCKET SPROCKET FLANGE SPROCKET SPROCKET DIMENSIONS BORE WT.NUMBER BUSHING TEETH P.D. O.D. O.D. I.D. TYPE (lbs)
RPP PANTHER ULTRA-CORD BELT SPROCKETS
STOCK SPROCKET DIMENSIONS14mm PITCH, 20mm BELT WIDTH (0.79 in), SPROCKET FACE WIDTH = 31mm (1.22 in)
14mm PITCH, 42mm BELT WIDTH (1.65 in), SPROCKET FACE WIDTH = 53mm (2.09 in)
NOTE: WEIGHTS FOR ALL BUSHED ITEMS ARE APPROXIMATE AND DO NOT INCLUDE THE BUSHINGS.
MIN MAXE K L M
28PTH14-20 SK 28 4.912 4.805 5.56 N/A C1F 0.62 N/A 1.88 0.03 0.500 2.625 3.229PTH14-20 SK 29 5.088 4.981 5.56 N/A C1F 0.62 N/A 1.88 0.03 0.500 2.625 3.630PTH14-20 SK 30 5.263 5.156 6.09 N/A C1F 0.62 N/A 1.88 0.03 0.500 2.625 4.032PTH14-20 SK 32 5.614 5.507 6.09 N/A C1F 0.62 N/A 1.88 0.03 0.500 2.625 4.934PTH14-20 SK 34 5.965 5.857 6.50 N/A C1F 0.62 N/A 1.88 0.03 0.500 2.625 5.836PTH14-20 SF 36 6.316 6.208 6.87 N/A C1F 0.62 N/A 2.00 0.15 0.500 2.938 6.438PTH14-20 SF 38 6.667 6.559 7.22 N/A C1F 0.62 N/A 2.00 0.15 0.500 2.938 7.540PTH14-20 SF 40 7.018 6.909 7.50 N/A C1F 0.62 N/A 2.00 0.15 0.500 2.938 8.644PTH14-20 E 44 7.720 7.611 8.34 N/A C1F 0.88 N/A 2.62 0.53 0.875 3.500 12.048PTH14-20 E 48 8.421 8.312 8.90 N/A C1F 0.88 N/A 2.62 0.53 0.875 3.500 14.752PTH14-20 E 52 9.123 9.014 9.68 N/A C1F 0.88 N/A 2.62 0.53 0.875 3.500 17.656PTH14-20 E 56 9.825 9.715 10.38 N/A C1F 0.88 N/A 2.62 0.53 0.875 3.500 21.060PTH14-20 E 60 10.527 10.417 11.06 N/A C1F 0.88 N/A 2.62 0 53 0.875 3.500 25.264PTH14-20 E 64 11.229 11.118 11.68 9.25 C2F 0.88 N/A 2.62 0.53 0.875 3.500 23.068PTH14-20 E 68 11.930 11.820 12.50 10.00 C2F 0.88 N/A 2.62 0.53 0.875 3.500 25.272PTH14-20 E 72 12.632 12.521 13.19 10.69 C2F 0.88 N/A 2.62 0.53 0.875 3.500 24.480PTH14-20 E 80 14.036 13.924 14.63 12.12 C2F 0.88 N/A 2.62 0.53 0.875 3.500 28.090PTH14-20 E 90 15.790 15.678 14.50 C3 1.06 -0.19 2.62 0.34 0.875 3.500 29.4112PTH14-20 E 112 19.650 19.535 18.38 C3 1.06 -0.19 2.62 0.34 0.875 3.500 39.1144PTH14-20 E 174 25.264 25.147 23.88 C3 1.06 -0.19 2.62 0.34 0.875 3.500 63.3168PTH14-20 F 168 29.475 29.356 28.25 C3 1.44 -0.44 3.62 0.96 1.000 4.000 131.0192PTH14-20 J 192 33.686 33.564 32.38 C3 1.88 -0.69 4.50 1.40 1.438 4.500 146.0216PTH14-20 J 216 37.896 37.772 36.38 C3 1.88 -0.69 4.50 1.40 1.438 4.500 171.0
28PTH14-42 SK 28 4.912 4.805 5.56 3.12 E1F 0.62 N/A 1.88 0.84 0.500 2.625 5.129PTH14-42 SK 29 5.088 4.981 5.56 3.12 E1F 0.62 N/A 1.88 0.84 0.500 2.625 5.830PTH14-42 SK 30 5.263 5.156 6.09 3.92 D1F 0.20 0.42 1.88 0.42 0.500 2.625 5.532PTH14-42 SK 32 5.614 5.507 6.09 3.92 D1F 0.20 0.42 1.88 0.42 0.500 2.625 7.034PTH14-42 SF 34 5.965 5.857 6.50 4.44 E1F 0.72 N/A 2.00 0.62 0.500 2.938 7.436PTH14-42 SF 36 6.316 6.208 6.87 4.84 D1F 0.20 0.42 2.00 0.30 0.500 2.938 8.538PTH14-42 SF 38 6.667 6.559 7.22 4.94 D1F 0.20 0.42 2.00 0.30 0.500 2.938 10.240PTH14-42 SF 40 7.018 6.909 7.50 5.06 D1F 0.20 0.42 2.00 0.30 0.500 2.938 11.944PTH14-42 E 44 7.720 7.611 8.34 6.12 D1F 0.64 0.23 2.62 0.11 0.875 3.500 14.648PTH14-42 E 48 8.421 8.312 8.90 6.50 D1F 0.64 0.23 2.62 0.11 0.875 3.500 18.852PTH14-42 E 52 9.123 9.014 9.68 7.18 D1F 0.64 0.23 2.62 0.11 0.875 3.500 23.056PTH14-42 E 56 9.825 9.715 10.38 7.88 D1F 0.64 0.23 2.62 0.11 0.875 3.500 27.460PTH14-42 E 60 10.527 10.417 11.06 8.50 D1F 0.64 0.23 2.62 0.11 0.875 3.500 32.264PTH14-42 E 64 11.229 11.118 11.68 9.25 D2F 0.64 0.23 2.62 0.11 0.875 3.500 28.068PTH14-42 E 68 11.930 11.820 12.50 10.00 D2F 0.64 0.23 2.62 0.11 0.875 3.500 31.272PTH14-42 E 72 12.632 12.521 13.19 10.69 D2F 0.64 0.23 2.62 0.11 0.875 3.500 30.280PTH14-42 E 80 14.036 13.924 14.63 12.12 D2F 0.64 0.23 2.62 0.11 0.875 3.500 34.090PTH14-42 F 90 15.790 15.678 14.50 C3 1.00 N/A 3.62 0.53 1.000 4.000 43.6112PTH14-42 F 112 19.650 19.535 18.38 C3 1.00 N/A 3.62 0.53 1.000 4.000 76.9144PTH14-42 F 144 25.264 25.147 23.88 C3 1.00 N/A 3.62 0.53 1.000 4.000 111.0168PTH14-42 F 168 29.475 29.356 28.25 C3 1.00 N/A 3.62 0.53 1.000 4.000 140.0192PTH14-42 J 192 33.686 33.564 32.38 C3 1.44 -0.25 4.50 0.97 1.438 4.500 158.0216PTH14-42 J 216 37.896 37.772 36.38 C3 1.44 -0.25 4.50 0.97 1.438 4.500 186.0
Type A Type B Type C Type D Type E Type MPB Type L
Type AF Type BF Type CF Type DF Type EF Type MPBF* Type LFBored-to-Suit
The figure following the sketch reference letter in the “Type” column indicates the construction of the sprocket.(1 = Solid, 2 = Web, and 3 = Arms), and the letter “F” indicates that the sprocket has flanges.
15
SPROCKET NO. OF SPROCKET SPROCKET FLANGE SPROCKET SPROCKET DIMENSIONS BORE WT.NUMBER BUSHING TEETH P.D. O.D. O.D. I.D. TYPE (lbs)MIN MAXE K L M
RPP PANTHER ULTRA-CORD BELT SPROCKETS
STOCK SPROCKET DIMENSIONS14mm PITCH, 65mm BELT WIDTH (2.56 in), SPROCKET FACE WIDTH = 77mm (3.03 in)
28PTH14-65 SFQ 28 4.912 4.805 5.56 3.12 L1F 1.06 N/A 1.25 1.97 0.500 2.375 6.729PTH14-65 SFQ 29 5.088 4.981 5.56 3.25 L1F 1.06 N/A 1.25 1.97 0.500 2.375 7.830PTH14-65 EQ 30 5.263 5.156 6.09 3.94 L1F 0.65 N/A 1.62 2.38 0.875 2.875 6.232PTH14-65 EQ 32 5.614 5.507 6.09 3.94 L1F 0.65 N/A 1.62 2.38 0.875 2.875 8.334PTH14-65 EQ 34 5.965 5.857 6.50 4.06 L1F 0.65 N/A 1.62 2.38 0.875 2.875 10.736PTH14-65 FQ 36 6.316 6.208 6.87 N/A L1F -0.47 N/A 2.50 3.50 1.000 3.125 11.438PTH14-65 FQ 38 6.667 6.559 7.22 N/A L1F -0.47 N/A 2.50 3.50 1.000 3.125 14 740PTH14-65 FQ 40 7.018 6.909 7.50 N/A L1F -0.47 N/A 2.50 3.50 1.000 3.125 17.844PTH14-65 E 44 7.720 7.611 8.34 6.12 A1F N/A 0.88 2.62 0.41 0.875 3.500 17.748PTH14-65 E 48 8.421 8.312 8.90 6.50 A1F N/A 0.88 2.62 0.41 0.875 3.500 23.052PTH14-65 E 52 9.123 9.014 9.68 7.18 A1F N/A 0.88 2.62 0.41 0.875 3.500 28.056PTH14-65 F 56 9.825 9.715 10.38 7.88 C1F 0.47 0.53 3.62 0.12 1.000 4.000 39.060PTH14-65 F 60 10.527 10.417 11.06 8.50 C1F 0.47 0.53 3.62 0.12 1.000 4.000 46.064PTH14-65 F 64 11.229 11.118 11.68 9.25 C1F 0.47 0.53 3.62 0.12 1.000 4.000 53.768PTH14-65 F 68 11.930 11.820 12.50 10.00 C2F 0.47 0.53 3.62 0.12 1.000 4.000 46.872PTH14-65 F 72 12.632 12.521 13.19 10.69 C2F 0.47 0.53 3.62 0.12 1.000 4.000 51.180PTH14-65 F 80 14.036 13.924 14.63 12.12 C2F 0.47 0.53 3.62 0.12 1.000 4.000 53.090PTH14-65 F 90 15.790 15.678 14.50 C3 0.47 0.53 3.62 0.12 1.000 4.000 52.3112PTH14-65 J 112 19.650 19.535 18.25 C3 1.19 N/A 4.50 0.28 1.438 4.500 82.6144PTH14-65 M 144 25.264 25.147 23.88 C3 1.94 -0.50 6.75 1.78 1.938 5.500 189.0168PTH14-65 M 168 29.475 29.356 28.09 C3 1.94 -0.50 6.75 1.78 1.938 5.500 208.0192PTH14-65 M 192 33.686 33.564 32.25 C3 1.94 -0.50 6.75 1.78 1.938 5.500 264.0216PTH14-65 M 216 37.896 37.772 36.38 C3 1.94 -0.50 6.75 1.78 1.938 5.500 303.0
14mm PITCH, 90mm BELT WIDTH (3.54 in), SPROCKET FACE WIDTH = 103mm (4.06 in)28PTH14-90 MPB 28 4.912 4.805 5.56 N/A MPB1F 1.00 3.69 5.06 N/A 0.875 2.625 18.929PTH14-90 MPB 29 5.088 4.981 5.56 N/A MPB1F 1.00 3.69 5.06 N/A 0.875 2.625 20.230PTH14-90 EQ 30 5.263 5.156 6.09 3.94 L1F 1.68 N/A 1.62 2.38 0.875 2.875 8.032PTH14-90 EQ 32 5.614 5.507 6.09 3.94 L1F 1.68 N/A 1.62 2.38 0.875 2.875 10.934PTH14-90 EQ 34 5.965 5.857 6.50 4.06 L1F 1.68 N/A 1.62 2.38 0.875 2.875 13.836PTH14-90 FQ 36 6.316 6.208 6.87 4.69 L1F 0.56 N/A 2.50 3.50 1.000 3.125 13.838PTH14-90 FQ 38 6.667 6.559 7.22 4.94 L1F 0.56 N/A 2.50 3.50 1.000 3.125 17.440PTH14-90 FQ 40 7.018 6.909 7.50 5.06 L1F 0.56 N/A 2.50 3.50 1.000 3.125 21.644PTH14-90 FQ 44 7.720 7.611 8.34 6.12 L1F 056 N/A 2.50 3.50 1.000 3.125 27.048PTH14-90 FQ 48 8.421 8.312 8.90 6.50 L1F 0.56 N/A 2.50 3.50 1.000 3.125 36.052PTH14-90 F 52 9.123 9.014 9.68 7.18 D1F 0.22 0.78 3.62 0.66 1.000 4.000 37.056PTH14-90 F 56 9.825 9.715 10.38 7.88 D1F 0.22 0.78 3.62 0.66 1.000 4.000 44.060PTH14-90 F 60 10.527 10.417 11.06 8.50 D1F 0.22 0.78 3.62 0.66 1.000 4.000 53.064PTH14-90 F 64 11.229 11.118 11.68 9.25 D1F 0.22 0.78 3.62 0.66 1.000 4.000 60.168PTH14-90 F 68 11.930 11.820 12.50 10.00 D2F 0.22 0.78 3.62 0.66 1.000 4.000 56.172PTH14-90 F 72 12.632 12.521 13.19 10.69 D2F 0.22 0.78 3.62 0.66 1.000 4.000 61.680PTH14-90 J 80 14.036 13.924 14.63 12.12 C2F 0.31 0.88 4.50 0.13 1.438 4.500 74.790PTH14-90 J 90 15.790 15.678 14.50 C2 0.31 0.88 4.50 0.13 1.438 4.500 67.0112PTH14-90 J 112 19.650 19.535 18.25 C3 0.31 0.88 4.50 0.13 1.438 4.500 90.6144PTH14-90 M 144 25.264 25.147 23.88 C3 1.44 N/A 6.75 1.25 1.938 5.500 199.0168PTH14-90 M 168 29.475 29.356 28.09 C3 1.44 N/A 6.75 1.25 1.938 5.500 235.0192PTH14-90 M 192 33.686 33.564 32.25 C3 1.44 N/A 6.75 1.25 1.938 5.500 271.0216PTH14-90 M 216 37.896 37.772 36.38 C3 1.44 N/A 6.75 1.25 1.938 5.500 377.0
14mm PITCH, 120mm BELT WIDTH (4.72 in), SPROCKET FACE WIDTH = 133mm (5.24 in)28PTH14-120 MPB 28 4.912 4.805 5.56 3.38 MPB1F 1.00 3.69 5.00 N/A 0.875 2.625 21.029PTH14-120 MPB 29 5.088 4.981 5.56 3.38 MPB1F 1.00 3.69 5.00 N/A 0.875 2.625 23.030PTH14-120 EQ 30 5.263 5.156 6.09 3.94 L1F 2.86 N/A 1.62 2.38 0.875 2.875 9.832PTH14-120 EQ 32 5.614 5.507 6.09 3.94 L1F 2.86 N/A 1.62 2.38 0.875 2.875 13.734PTH14-120 FQ 34 5.965 5.857 6.50 4.44 L1F 1.74 N/A 2.50 3.50 1.000 3.125 14.436PTH14-120 FQ 36 6.316 6.208 6.87 4.69 L1F 1.74 N/A 2.50 3.50 1.000 3.125 17.038PTH14-120 FQ 38 6.667 6.559 7.22 4.94 L1F 1.74 N/A 2.50 3.50 1.000 3.125 21.540PTH14-120 FQ 40 7.018 6.909 7.50 5.06 L1F 1.74 N/A 2.50 3.50 1.000 3.125 31.944PTH14-120 FQ 44 7.720 7.611 8.34 6.12 L1F 1.74 N/A 2.50 3.50 1.000 3.125 31.948PTH14-120 FQ 48 8.421 8.312 8.90 6.50 L1F 1.74 N/A 2.50 3.50 1.000 3.125 41.352PTH14-120 F 52 9.123 9.014 9.68 7.18 A1F 0.37 1.37 3.62 1.24 1.000 4.000 43.056PTH14-120 F 56 9.825 9.715 10.38 7.88 A1F 0.37 1.37 3.62 1.24 1.000 4.000 51.160PTH14-120 F 60 10.527 10.417 11.06 8.50 A1F 0.37 1.37 3.62 1.24 1.000 4.000 59.864PTH14-120 J 64 11.229 11.118 11.68 9.25 D1F 0.17 1.02 4.50 0.91 1.438 4.500 73.068PTH14-120 J 68 11.930 11.820 12.50 10.00 D1F 0.17 1.02 4.50 0.91 1.438 4.500 84.072PTH14-120 J 72 12.632 12.521 13.19 10.69 D1F 0.17 1.02 4.50 0.91 1.438 4.500 96.080PTH14-120 J 80 14.036 13.924 14.63 12.12 D2F 0.17 1.02 4.50 0.91 1.438 4.500 86.090PTH14-120 M 90 15.790 15.678 14.50 C2 1.39 0.05 6.75 0.12 1.938 5.500 150.0112PTH14-120 M 112 19.650 19.535 18.25 C3 1.39 0.05 6.75 0.12 1.938 5.500 157.0144PTH14-120 M 144 25.264 25.147 21.75 C3 1.39 0.05 6.75 0.12 1.938 5.500 214.0168PTH14-120 M 168 29.475 29.356 28.09 C3 1 39 0.05 6.75 0.12 1.938 5.500 273.0192PTH14-120 N 192 33.686 33.564 32.25 C3 1.75 N/A 8.12 1.13 2.938 6.000 365.0216PTH14-120 N 216 37.896 37.772 36.38 C3 1.75 N/A 8.12 1.13 2.938 6.000 423.0
NOTE: WEIGHTS FOR ALL BUSHED ITEMS ARE APPROXIMATE AND DO NOT INCLUDE THE BUSHINGS.
16
QD Bushings
QD FLANGED BUSHINGS & Q SERIES FLANGELESS
The QD design is the most widely used bushing in the industry. Flanged with an internal keyway andcompletely split for easy installation. Special tapered surfaces improve grip. Axial movement is virtuallyeliminated.
Bushings are designed to transmit the rated torque capacity listed in the table below when the cap screwsare tightened as indicated. The bushings are stocked in all popular bore sizes, including metric bores, with-in the bore range for a particular bushing.
QD FLANGED BUSHINGS
“Q” SERIES FLANGLESS
BUSHING DIMENSIONS
(1) SF bushings with bores 2-3/16" and larger — ductile iron (2) E bushings with bores 2-11/16" and larger — ductile iron(3) F bushings with bores 3-3/16" and larger — ductile iron(4) J bushings with bores 3-11/16" and larger — ductile iron(5) Minimum plain bore and Flangeless bushings are unsplit.Note: See pages 17 through 21 for a complete listing of standard bore sizes.
Weight Range,Bolt Pounds Cap ScrewsCircle Max Min Required
Bushing A B D L Diameter Bore Bore quantity size
QT 1/4 1.625 2-1/2 1-1/4 2 0.2 0.5 2 1/4 X 3/4JA 5/16 1.375 2 1 1.66 0.2 0.5 3 10-24 X 1SH 7/16 1.871 2-5/8 1-5/16 2.25 0.6 1.2 3 1/4 X 1-3/8SDS 7/16 2.187 3-1/8 1-5/16 2.69 0.8 1.7 3 1/4 X 1-3/8SD 7/16 2.187 3-1/8 1-13/16 2.69 0.9 2.2 3 1/4 X 1-7/8SK 9/16 2.812 3-7/8 1-15/16 3.31 1.5 3.9 3 5/16 X 2SF 5/8 3.125 4-5/8 2-1/16 3.88 2.2 5.4 3 3/8 X 2SFQ - 3.125 - 1-1/8 2-3/4 0.9 2.1 4 1/4 x 1-1/2SKQ - 2.8125 - 1-1/8 2-3/8 0.8 1.7 3 1/4 x 1-1/2E 7/8 3.834 6 2-3/4 5 5.6 11.7 3 1/2 X 2-3/4EQ - 3.834 - 1-1/2 3-3/8 1.8 4.1 4 5/16 x 1-3/4F 1 4.437 6-5/8 3-3/4 5.63 8.5 19.4 3 9/16 X 3-5/8FQ - 4.4375 - 2-3/8 3-3/4 4.6 8.5 4 3/8 x 2J 1-1/8 5.145 7-1/4 4-5/8 6.25 12.8 28.6 3 5/8 x 4-1/2M 1-1/4 6.496 9 6-3/4 7.88 29.5 63.4 4 3/4 X 6-3/4N 1-1/2 6.992 10 8-1/8 8.5 46 95 4 7/8 X 8P 1-3/4 8.242 11-3/4 9-3/8 10 88 178 4 1 X 9-1/2W 2 10.429 15 11-3/8 12.75 155 262 4 1-1/8 X 11-1/2S 2-3/4 12.125 17-3/4 15-1/4 15 285 410 5 1-1/4 X 15
For complete bushing part number, include a dash andthe bore size.EXAMPLE: SDS-1-1/4 or QT-7/8
Additional bore sizes available but may not be in stock.
Torque Capacity(In.-Lbs.) G F
1,750 1/8 7/81,750 1/8 9/163,500 1/8 13/165,000 1/8 3/45,000 1/8 1-1/47,000 1/8 1-1/411,000 1/8 1-1/411,000 - 1-1/87,000 - 1-1/820,000 1/8 1-5/820,000 - 1-1/240,000 3/16 2-1/245,000 - 2-3/855,000 3/16 3-3/16125,000 3/16 5-3/16150,000 1/4 6-1/4250,000 1/4 7-1/4375,000 1/4 9625,000 3/8 12
17
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
QT BUSHINGSQT-7/16 7/16 no keyseat 0.6QT-1/2 1/2 1/8 x 1/16 0.6QT-9/16 9/16 1/8 x 1/16 0.6QT-5/8 5/8 3/16 x 3/32 0.6QT-11/16 11/16 3/16 x 3/32 0.6QT-3/4 3/4 3/16 x 3/32 0.6QT-13/16 13/16 3/16 x 3/32 0.6QT-7/8 7/8 3/16 x 3/32 0.6QT-15/16 15/16 1/4 x 1/8 0.6QT-1 1 1/4 x 1/8 0.6QT-1-1/16 1-1/16 1/4 x 1/8 0.6QT-1-1/8 1-1/8 1/4 x 1/8 0.6QT-1-3/16 1-3/16 1/4 x 1/8 0.6QT-1-1/4 1-1/4 1/4 x 1/8 0.6QT-1-5/16 1-5/16 5/16 x 1/16 0.6QT-1-3/8 1-3/8 5/16 x 1/16 0.6QT-1-7/16 1-7/16 3/8 x 1/16 0.6
JA BUSHINGSJA-1/2NK 1/2 no keyseat 0.8JA-1/2 1/2 1/8 x 1/16 0.8JA-9/16 9/16 1/8 x 1/16 0.8JA-5/8 5/8 3/16 x 3/32 0.8JA-11/16 11/16 3/16 x 3/32 0.8JA-3/4 3/4 3/16 x 3/32 0.8JA-13/16 13/16 3/16 x 3/32 0.8JA-7/8 7/8 3/16 x 3/32 0.8JA-15/16 15/16 1/4 x 1/8 0.8JA-1 1 1/4 x 1/8 0.8JA-1-1/16 1-1/16 1/4 x 1/16 0.8JA-1-1/8 1-1/8 1/4 x 1/16 0.8JA-1-3/16 1-3/16 1/4 x 1/16 0.8JA-1-1/4 1-1/4 1/4 x 1/32 0.8
SH BUSHINGSSH-7/16 7/16 no keyseat 1.1SH-1/2 1/2 1/8 x 1/16 1.1SH-9/16 9/16 1/8 x 1/16 1.1SH-5/8 5/8 3/16 x 3/32 1.1SH-11/16 11/16 3/16 x 3/32 1.0SH-3/4 3/4 3/16 x 3/32 1.0SH-13/16 13/16 3/16 x 3/32 1.0SH-7/8 7/8 3/16 x 3/32 1.0SH-15/16 15/16 1/4 x 1/8 1.0SH-1 1 1/4 x 1/8 0.9SH-1-1/16 1-1/16 1/4 x 1/8 0.9SH-1-1/8 1-1/8 1/4 x 1/8 0.9SH-1-3/16 1-3/16 1/4 x 1/8 0.8
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
SH BUSHINGSSH-1-1/4 1-1/4 1/4 x 1/8 0.8SH-1-5/16 1-5/16 5/16 x 5/32 0.7SH-1-3/8 1-3/8 5/16 x 5/32 0.7SH-1-7/16 1-7/16 3/8 x 1/16 0.7SH-1-1/2 1-1/2 3/8 x 1/16 0.6SH-1-9/16 1-9/16 3/8 x 1/16 0.6SH-1-5/8 1-5/8 3/8 x 1/16 0.5SH-1-11/16 1-11/16 no keyseat 0.5
SDS BUSHINGSSDS-7/16 7/16 no keyseat 1.7SDS-1/2 1/2 1/8 x 1/16 1.7SDS-9/16 9/16 1/8 x 1/16 1.7SDS-5/8 5/8 3/16 x 3/32 1.6SDS-11/16 11/16 3/16 x 3/32 1.6SDS-3/4 3/4 3/16 x 3/32 1.6SDS-13/16 13/16 3/16 x 3/32 1.6SDS-7/8 7/8 3/16 x 3/32 1.5SDS-15/16 15/16 1/4 x 1/8 1.5SDS-1 1 1/4 x 1/8 1.5SDS-1-11/16 1-1/16 1/4 x 1/8 1.4SDS-1-1/8 1-1/8 1/4 x 1/8 1.4SDS-1-3/16 1-3/16 1/4 x 1/8 1.4SDS-1-1/4 1-1/4 1/4 x 1/8 1.3SDS-1-5/16 1-5/16 5/16 x 5/32 1.3SDS-1-3/8 1-3/8 5/16 x 5/32 1.2SDS-13838KS 1-3/8 3/8 x 3/16 1.2SDS-1-7/16 1-7/16 3/8 x 3/16 1.2SDS-1-1/2 1-1/2 3/8 x 3/16 1.1SDS-1-9/16 1-9/16 3/8 x 3/16 1.1SDS-1-5/8 1-5/8 3/8 x 3/16 1.0SDS-1-11/16 1-11/16 3/8 x 3/16 1.0SDS-1-3/4 1-3/4 3/8 x 1/8 1.0SDS-1-13/16 1-13/16 1/2 x 1/8 0.9SDS-1-7/8 1-7/8 1/2 x 1/16 0.9SDS-1-15/16 1-15/16 1/2 x 1/16 0.8SDS-2 2 no keyseat 0.7
SD BUSHINGSSD-7/16 7/16 no keyseat 2.1SD-1/2 1/2 1/8 x 1/16 2.1SD-9/16 9/16 1/8 x 1/16 2.1SD-5/8 5/8 3/16 x 3/32 2.1SD-11/16 11/16 3/16 x 3/32 2.0SD-3/4 3/4 3/16 x 3/32 2.0SD-13/16 13/16 3/16 x 3/32 2.0SD-7/8 7/8 3/16 x 3/32 1.9SD-15/16 15/16 1/4 x 1/8 1.9
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
SD BUSHINGSSD-1 1 1/4 x 1/8 1.8SD-1-1/16 1-1/16 1/4 x 1/8 1.8SD-1-1/8 1-1/8 1/4 x 1/8 1.7SD-1-3/16 1-3/16 1/4 x 1/8 1.7SD-1-1/4 1-1/4 1/4 x 1/8 1.6SD-1-5/16 1-5/16 5/16 x 5/32 1.6SD-1-3/8 1-3/8 5/16 x 5/32 1.5SD-13838KS 1-3/8 3/8 x 3/16 1.5SD-1-7/16 1-7/16 3/8 x 3/16 1.4SD-1-1/2 1-1/2 3/8 x 3/16 1.4SD-1-9/16 1-9/16 3/8 x 3/16 1.3SD-1-5/8 1-5/8 3/8 x 3/16 1.2SD-1-11/16 1-11/16 3/8 x 3/16 1.2SD-1-3/4 1-3/4 3/8 x 1/8 1.1SD-1-13/16 1-13/16 1/2 x 1/8 1.1SD-1-7/8 1-7/8 1/2 x 1/1/6 1.0SD-1-15/16 1-15/16 1/2 x 1/16 0.9SD-2 2 no keyseat 0.8
SK BUSHINGSSK-7/16 7/16 no keyseat 3.6SK-1/2 1/2 1/8 x 1/16 3.6SK-9/16 9/16 1/8 x 1/16 3.6SK-5/8 5/8 3/16 x 3/32 3.6SK-11/16 11/16 3/16 x 3/32 3.5SK-3/4 3/4 3/16 x 3/32 3.5SK-13/16 13/16 3/16 x 3/32 3.5SK-7/8 7/8 3/16 x 3/32 3.4SK-15/16 15/16 1/4 x 1/8 3.4SK-1 1 1/4 x 1/8 3.3SK-1-1/16 1-1/16 1/4 x 1/8 3.3SK-1-1/8 1-1/8 1/4 x 1/8 3.2SK-1-3/16 1-3/16 1/4 x 1/8 3.2SK-1-1/4 1-1/4 1/4 x 1/8 3.1SK-1-5/16 1-5/16 5/16 x 5/32 3.1SK-1-5/16 1-5/16 3/8 x 3/16 3.1SK-1-3/8 1-3/8 5/16 x 5/32 3.0SK-13838KS 1-3/8 3/8 x 3/16 3.0SK-1-7/16 1-7/16 3/8 x 3/16 2.9SK-1-1/2 1-1/2 3/8 x 3/16 2.9SK-1-9/16 1-9/16 3/8 x 3/16 2.8SK-1-5/8 1-5/8 3/8 x 3/16 2.7SK-1-11/16 1-11/16 3/8 x 3/16 2.6SK-1-3/4 1-3/4 3/8 x 3/16 2.5SK-13412KS 1-3/4 1/2 x 1/4 2.5SK-1-13/16 1-13/16 1/2 x 1/4 2.4SK-1-7/8 1-7/8 1/2 x 1/4 2.4
QD Bushings Bore & Keyset Dimensions
Standard keyseats are used in the bore of all bushings. However, as the bore increases in size, it may be necessaryto reduce the depth of the keyseat. When this happens, the correct rectangular key to suit is furnished at no charge.This does not affect the ability of the bushing to carry the load. The rectangular key, or flat key as some call it, fits inthe standard keyway in the shaft.
18
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
SK BUSHINGSSK-1-15/16 1-15/16 1/2 x 1/4 2.3SK-2 2 1/2 x 1/4 2.2SK-2-1/16 2-1/16 1/2 x 1/4 2.1SK-2-1/8 2-1/8 1/2 x 1/4 2.0SK-2-3/16 2-3/16 1/2 x 1/8 2.0SK-2-1/4 2-1/4 1/2 x 1/8 1.9SK-21458KS 2-1/4 5/8 x 1/8 1.9SK-2-5/16 2-5/16 5/8 x 1/16 1.8SK-2-3/8 2-3/8 5/8 x 1/16 1.7SK-2-7/16 2-7/16 5/8 x 1/16 1.6SK-2-1/2 2-1/2 5/8 x 1/16 1.5SK-2-9/16 2-9/16 no keyseat 1.3SK-2-5/8 2-5/8 no keyseat 1.1
SF BUSHINGSSF-1/2NK 1/2 no keyseat 5.1SF-1/2NK 1/2 1/8 x 1/16 5.1SF-5/8 5/8 3/16 x 3/32 5.0SF-3/4 3/4 3/16 x 3/32 5.0SF-7/8 7/8 3/16 x 3/32 4.9SF-15/16 15/16 1/4 x 1/8 4.8SF-1-1/16 1-1/16 1/4 x 1/8 4.7SF-1-1/8 1-1/8 1/4 x 1/8 4.7SF-1-3/16 1-3/16 1/4 x 1/8 4.6SF-1-1/4 1-1/4 1/4 x 1/8 4.5SF-1-5/16 1-5/16 5/16 x 5/32 4.5SF-1-3/8 1-3/8 5/16 x 5/32 4.4SF-13838KS 1-3/8 3/8 x 3/16 4.4SF-1-7/16 1-7/16 3/8 x 3/16 4.3SF-1-1/2 1-1/2 3/8 x 3/16 4.2SF-1-9/16 1-9/16 3/8 x 3/16 4.2SF-1-5/8 1-5/8 3/8 x 3/16 4.1SF-1-11/16 1-11/16 3/8 x 3/16 4.0SF-1-3/4 1-3/4 3/8 x 3/16 3.9SF-1-13/16 1-13/16 1/2 x 1/4 3.8SF-1-7/8 1-7/8 1/2 x 1/4 3.7SF-1-15/16 1-15/16 1/2 x 1/4 3.6SF-2 2 1/2 x 1/4 3.5SF-2-1/16 2-1/16 1/2 x 1/4 3.4SF-2-1/8 2-1/8 1/2 x 1/4 3.3SF-2-3/16 2-3/16 1/2 x 1/4 3.2SF-2-1/4 2-1/4 1/2 x 1/4 3.1SF-21458KS 2-1/4 5/8 x 5/16 3.1SF-2-5/16 2-5/16 5/8 x 3/16 3.1SF-2-3/8 2-3/8 5/8 x 3/16 3.0SF-2-7/16 2-7/16 5/8 x 3/16 2.9SF-2-1/2 2-1/2 5/8 x 3/16 2.8SF-2-9/16 2-9/16 5/8 x 1/16 2.6SF-2-5/8 2-5/8 5/8 x 1/16 2.5SF-2-11/16 2-11/16 5/8 x 1/16 2.4SF-2-3/4 2-3/4 5/8 x 1/16 2.2SF-2-7/8 2-7/8 3/4 x 1/16 1.8
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
SF BUSHINGSSF-2-15/16 2-15/16 3/4 x 1/32 1.7
E BUSHINGSE-7/8NK 7/8 no keyseat 10.8E-7/8 7/8 3/16 x 3/32 10.8E-15/16 15/16 1/4 x 1/8 10.8E-15/16 1 1/4 x 1/8 10.7E-1-1/8 1-1/8 1/4 x 1/8 10.6E-1-3/16 1-3/16 1/4 x 1/8 10.5E-1-1/4 1-1/4 1/4 x 1/8 10.4E-1-15/16 1-15/16 5/16 x 5/32 10.3E-1-3/8 1-3/8 5/16 x 5/32 10.2E-13838KS 1-3/8 3/8 x 3/16 10.2E-1-7/16 1-7/16 3/8 x 3/16 10.1E-1-1/2 1-1/2 3/8 x 3/16 10.0E-1-9/16 1-9/16 3/8 x 3/16 9.9E-1-5/8 1-5/8 3/8 x 3/16 9.8E-1-11/16 1-11/16 3/8 x 3/16 9.7E-1-3/4 1-3/4 3/8 x 3/16 9.6E-1-13/16 1-13/16 1/2 x 1/4 9.4E-1-7/8 1-7/8 1/2 x 1/4 9.3E-1-15/16 1-15/16 1/2 x 1/4 9.2E-2 2 1/2 x 1/4 9.0E-2-1/16 2-1/16 1/2 x 1/4 8.9E-2-1/8 2-1/8 1/2 x 1/4 8.8E-2-3/16 2-3/16 1/2 x 1/4 8.6E-2-1/4 2-1/4 1/2 x 1/4 8.5E-21458KS 2-1/4 5/8 x 5/16 8.5E-2-5/16 2-5/16 5/8 x 5/16 8.3E-2-3/8 2-3/8 5/8 x 5/16 8.1E-2-7/16 2-7/16 5/8 x 5/16 8.0E-2-1/2 2-1/2 5/8 x 5/16 7.8E-2-9/16 2-9/16 5/8 x 5/16 7.6E-2-5/8 2-5/8 5/8 x 5/16 7.5E-2-11/16 2-11/16 5/8 x 5/16 7.3E-2-3/4 2-3/4 5/8 x 5/16 7.1E-2-13/16 2-13/16 3/4 x 3/8 7.2E-2-7/8 2-7/8 3/4 x 3/8 7.1E-2-15/16 2-15/16 3/4 x 1/8 6.9E-3 3 3/4 x 1/8 6.7E-3-1/8 3-1/8 3/4 x 1/8 6.3E-3-3/16 3-3/16 3/4 x 1/8 6.0E-3-1/4 3-1/4 3/4 x 1/8 5.8E-3-5/16 3-5/16 7/8 x 1/16 5.7E-3-3/8 3-3/8 7/8 x 1/16 5.5E-3-7/16 3-7/16 7/8 x 1/16 5.2E-3-1/2 3-1/2 7/8 x 1/16 4.7
F BUSHINGSF-1NK 1 no keyseat 17.9F-1 1 1/4 x 1/8 17.9F-1-1/8 1-1/8 1/4 x 1/8 17.7F-1-3/16 1-3/16 1/4 x 1/8 17.6
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
F BUSHINGSF-1-1/4 1-1/4 1/4 x 1/8 17.5F-1-3/8 1-3/8 5/16 x 5/32 17.2F-1-7/16 1-7/16 3/8 x 3/16 17.1F-1-1/2 1-1/2 3/8 x 3/16 16.9F-1-9/16 1-9/16 3/8 x 3/16 16.8F-1-5/8 1-5/8 3/8 x 3/16 16.7F-1-3/4 1-3/4 3/8 x 3/16 16.3F-1-7/8 1-7/8 1/2 x 1/4 16.0F-1-15/16 1-15/16 1/2 x 1/4 15.8F-2 2 1/2 x 1/4 15.6F-2-1/16 2-1/16 1/2 x 1/4 15.4F-2-1/8 2-1/8 1/2 x 1/4 15.2F-2-3/16 2-3/16 1/2 x 1/4 15.0F-2-5/16 2-5/16 5/8 x 5/16 14.5F-2-3/8 2-3/8 5/8 x 5/16 14.3F-2-7/16 2-7/16 5/8 x 5/16 14.1F-2-1/2 2-1/2 5/8 x 5/16 13.9F-2-9/16 2-9/16 5/8 x 5/16 13.7F-2-5/8 2-5/8 5/8 x 5/16 13.4F-2-11/16 2-11/16 5/8 x 5/16 13.2F-2-3/4 2-3/4 5/8 x 5/16 12.9F-2-13/16 2-13/16 3/4 x 3/8 12.6F-2-7/8 2-7/8 3/4 x 3/8 12.3F-2-15/16 2-15/16 3/4 x 3/8 12.1F-3 3 3/4 x 3/8 11.8F-3-1/8 3-1/8 3/4 x 3/8 11.2F-3-3/16 3-3/16 3/4 x 3/8 10.9F-3-1/4 3-1/4 3/4 x 3/8 10.6F-3-5/16 3-5/16 7/8 x 3/16 11.0F-3-3/8 3-3/8 7/8 x 3/16 10.6F-3-7/16 3-7/16 7/8 x 3/16 10.3F-3-1/2 3-1/2 7/8 x 3/16 10.0F-3-5/8 3-5/8 7/8 x 3/16 9.4F-3-11/16 3-11/16 7/8 x 3/16 9.0F-3-3/4 3-3/4 7/8 x 3/16 8.7F-3-7/8 3-7/8 1 x 1/8 8.1F-3-15/16 3-15/16 1 x 1/8 7.7F-4 4 no keyseat 6.9
J BUSHINGSJ-1-7/16NK 1-7/16 no keyseat 28.1J-1-7/16 1-7/16 3/8 x 3/16 28.1J-1-1/2 1-1/2 3/8 x 3/16 28.0J-1-9/16 1-9/16 3/8 x 3/16 27.8J-1-11/16 1-11/16 3/8 x 3/16 27.4J-1-3/4 1-3/4 3/8 x 3/16 27.2J-1-7/8 1-7/8 1/2 x 1/4 26.7J-1-15/16 1-15/16 1/2 x 1/4 26.5J-2 2 1/2 x 1/4 26.3J-2-1/8 2-1/8 1/2 x 1/4 25.8J-2-3/16 2-3/16 1/2 x 1/4 25.6J-2-1/4 2-1/4 1/2 x 1/4 25.3
Continued
QD Bushings Bore & Keyset Dimensions
19
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
J BUSHINGSJ-2-5/16 2-5/16 5/8 x 5/16 25.0J-2-3/8 2-3/8 5/8 x 5/16 24.7J-2-7/16 2-7/16 5/8 x 5/16 24.5J-2-1/2 2-1/2 5/8 x 5/16 24.2J-2-5/8 2-5/8 5/8 x 5/16 23.6J-2-11/16 2-11/16 5/8 x 5/16 23.3J-2-3/4 2-3/4 5/8 x 5/16 23.0J-2-7/8 2-7/8 3/4 x 3/8 22.2J-2-15/16 2-15/16 3/4 x 3/8 21.9J-3 3 3/4 x 3/8 21.6J-3-1/8 3-1/8 3/4 x 3/8 20.9J-3-3/16 3-3/16 3/4 x 3/8 20.5J-3-1/4 3-1/4 3/4 x 3/8 20.1J-3-5/16 3-5/16 7/8 x 7/16 19.6J-3-3/8 3-3/8 7/8 x 7/16 19.3J-3-7/16 3-7/16 7/8 x 7/16 18.9J-3-1/2 3-1/2 7/8 x 7/16 18.5J-3-5/8 3-5/8 7/8 x 7/16 17.7J-3-11/16 3-11/16 7/8 x 7/16 17.2J-3-3/4 3-3/4 7/8 x 7/16 16.8J-3-3/16 3-13/16 1 x 1/2 17.4J-3-7/8 3-7/8 1 x 3/8 17.0J-3-15/16 3-15/16 1 x 3/8 16.5J-4 4 1 x 1/8 16.1J-4-1/8 4-1/8 1 x 1/8 15.2J-4-3/16 4-3/16 1 x 1/8 14.7J-4-1/4 4-1/4 1 x 1/8 14.2J-4-3/8 4-3/8 1 x 1/8 13.2J-4/7/16 4-7/16 1 x 1/8 12.7J-4-1/2 4-1/2 1 x 1/8 12.2
M BUSHINGSM-1-15/16 1-15/16 1/2 x 1/4 63.7M-2 2 1/2 x 1/4 63.3M-2-3/16 2-3/16 1/2 x 1/4 62.3M-2-1/4 2-1/4 1/2 x 1/4 61.9M-2-3/8 2-3/8 5/8 x 5/16 61.0M-2-7/16 2-7/16 5/8 x 5/16 60.6M-2-1/2 2-1/2 5/8 x 5/16 60.1M-2-5/8 2-5/8 5/8 x 5/16 59.3M-2-11/16 2-11/16 5/8 x 5/16 58.8M-2-3/4 2-3/4 5/8 x 5/16 58.3M-2-7/8 2-7/8 3/4 x 3/8 57.2M-2-15/16 2-15/16 3/4 x 3/8 56.7M-3 3 3/4 x 3/8 56.2M-3-1/8 3-1/8 3/4 x 3/8 55.2M-3-3/16 3-3/16 3/4 x 3/8 54.6M-3-1/4 3-1/4 3/4 x 3/8 54.1M-3-3/8 3-3/8 7/8 x 7/16 52.8M-3-7/16 3-7/16 7/8 x 7/16 52.2M-3-1/2 3-1/2 7/8 x 7/16 51.6M-3-5/8 3-5/8 7/8 x 7/16 50.4
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
M BUSHINGSM-3-11/16 3-11/16 7/8 x 7/16 49.7M-3-3/4 3-3/4 7/8 x 7/16 49.1M-3-7/8 3-7/8 1 x 1/2 47.6M-3-15/16 3-15/16 1 x 1/2 46.9M-4 4 1 x 1/2 46.2M-4-1/8 4-1/8 1 x 1/2 44.8M-4-3/16 4-3/16 1 x 1/2 44.1M-4-1/4 4-1/4 1 x 1/2 43.4M-4-3/8 4-3/8 1 x 1/2 41.9M-4-7/16 4-7/16 1 x 1/2 41.2M-4-1/2 4-1/2 1 x 1/2 40.4M-4-11/16 4-11/16 1-1/4 x 5/8 37.5M-4-3/4 4-3/4 1-1/4 x 5/8 36.7M-4-7/8 4-7/8 1-1/4 x 1/4 37.8M-4-15/16 4-15/16 1-1/4 x 1/4 37.0M-5 5 1-1/4 x 1/4 36.1M-5-3/16 5-3/16 1-1/4 x 1/4 33.5M-5-1/4 5-1/4 1-1/4 x 1/4 32.6M-5-7/16 5-7/16 1-1/4 x 1/4 29.9M-5-1/2 5-1/2 1-1/4 x 1/4 28.9
N BUSHINGSN-2-15/16 2-15/16 3/4 x 3/8 84.1N-3 3 3/4 x 3/8 83.5N-3-3/8 3-3/8 7/8 x 7/16 79.3N-3-7/16 3-7/16 7/8 x 7/16 78.6N-3-1/2 3-1/2 7/8 x 7/16 77.9N-3-5/8 3-5/8 7/8 x 7/16 76.4N-3-3/4 3-3/4 7/8 x 7/16 74.9N-3-7/8 3-7/8 1 x 1/2 73.1N-3-15/16 3-15/16 1 x 1/2 72.3N-4 4 1 x 1/2 71.5N-4-3/16 4-3/16 1 x 1/2 68.9N-4-1/4 4-1/4 1 x 1/2 68.1N-4-3/8 4-3/8 1 x 1/2 66.3N-4-7/16 4-7/16 1 x 1/2 65.4N-4-1/2 4-1/2 1 x 1/2 64.5N-4-5/8 4-5/8 1-1/4 x 5/8 62.0N-4-3/4 4-3/4 1-1/4 x 5/8 60.0N-4-7/8 4-7/8 1-1/4 x 5/8 58.1N-4-15/16 4-15/16 1-1/4 x 5/8 57.0N-5 5 1-1/4 x 5/8 56.0N-5-3/16 5-3/16 1-1/4 x 1/4 56.1N-5-7/16 5-7/16 1-1/4 x 1/4 51.7N-5-1/2 5-1/2 1-1/4 x 1/4 50.6N-5-7/8 5-7/8 1-1/2 x 1/4 44.3N-5-15/16 5-15/16 1-1/2 x 1/8 43.9
P BUSHINGSP-2-15/16 2-15/16 3/4 x 3/8 141.2P-3-1/4 3-1/4 3/4 x 3/8 137.6P-3-7/16 3-7/16 7/8 x 7/16 134.9P-3-1/2 3-1/2 7/8 x 7/16 134.1
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
P BUSHINGSP-3-5/8 3-5/8 7/8 x 7/16 132.4P-3-3/4 3-3/4 7/8 x 7/16 130.6P-3-7/8 3-7/8 1 x 1/2 128.5P-3-15/16 3-15/16 1 x 1/2 127.6P-4 4 1 x 1/2 126.7P-4-1/4 4-1/4 1 x 1/2 122.7P-4-3/8 4-3/8 1 x 1/2 120.7P-4-7/16 4-7/16 1 x 1/2 119.6P-4-1/2 4-1/2 1 x 1/2 118.6P-4-5/8 4-5/8 1-1/4 x 5/8 115.7P-4-11/16 4-11/16 1-1/4 x 5/8 114.6P-4-3/4 4-3/4 1-1/4 x 5/8 113.5P-4-7/8 4-7/8 1-1/4 x 5/8 111.2P-4-15/16 4-15/16 1-1/4 x 5/8 110.0P-5 5 1-1/4 x 5/8 108.8P-5-3/16 5-3/16 1-1/4 x 5/8 105.2P-5-1/4 5-1/4 1-1/4 x 5/8 103.9P-5-5/16 5-5/16 1-1/4 x 5/8 102.7P-5-3/8 5-3/8 1-1/4 x 5/8 101.4P-5-7/16 5-7/16 1-1/4 x 5/8 100.1P-5-1/2 5-1/2 1-1/4 x 5/8 98.8P-5-3/4 5-3/4 1-1/2 x 3/4 98.1P-5-7/8 5-7/8 1-1/2 x 1/4 95.3P-5-15/16 5-15/16 1-1/2 x 1/4 93.9P-6 6 1-1/2 x 1/4 92.5P-6-1/16 6-1/16 1-1/2 x 1/4 91.0P-6-1/4 6-1/4 1-1/2 x 1/4 86.6P-6-7/16 6-7/16 1-1/2 x 1/4 83.5P-6-1/2 6-1/2 1-1/2 x 1/4 80.5P-6-3/4 6-3/4 1-3/4 x 1/8 74.7P-7 7 1-3/4 x 1/8 68.1
W BUSHINGSW4-1/4 4-1/4 — 247.0W-4-7/8 4-7/8 — 234.0W-5-1/4 5-1/4 — 225.0W-5-7/8 5-7/8 — 209.0W-6-1/2 6-1/2 — 191.0W-7-1/4 7-1/4 — 167.0
S BUSHINGSS-6 6 — 445.0S-8 8 — 356.0S-9 9 — 301.0
FLANGELESS QD BUSHINGSSKQ BUSHINGS
SKQ-MPB 1/2 MPB unsplit 1.7SKQ-1 1 1/4 x 1/8 1.6SKQ-1-1/8 1-1/8 1/4 x 1/8 1.5SKQ-1-3/16 1-3/16 1/4 x 1/8 1.4SKQ-1-3/8 1-3/8 5/16 x 5/32 1.3SKQ-1-1/2 1-1/2 3/8 x 3/16 1.2SKQ-1-5/8 1-5/8 3/8 x 3/16 1.1
Continued
QD Bushings Bore & Keyset Dimensions
20
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
FLANGELESS QD BUSHINGSSKQ BUSHINGS
SKQ-1-3/4 1-3/4 3/8 x 3/16 1.0SKQ-1-7/8 1-7/8 1/2 x 1/4 0.9SKQ-1-15/16 1-15/16 1/2 x 1/4 0.8
SFQ BUSHINGSSFQ-MPB 1/2 MPB unsplit 2.1SFQ-1 1 1/4 x 1/8 2.0SFQ-1-1/8 1-1/8 1/4 x 1/8 1.9SFQ-1-3/16 1-3/16 1/4 x 1/8 1.8SFQ-1-3/8 1-3/8 5/16 x 5/32 1.7SFQ-1-1/2 1-1/2 3/8 x 3/16 1.6SFQ-1-5/8 1-5/8 3/8 x 3/16 1.5SFQ-1-3/4 1-3/4 3/8 x 3/16 1.4SFQ-1-7/8 1-7/8 1/2 x 1/4 1.3SFQ-1-5/16 1-5/16 1/2 x 1/4 1.3SFQ-2 2 1/2 x 1/4 1.2SFQ-2-1/8 2-1/8 1/2 x 1/4 1.1SFQ-2-3/16 2-3/16 1/2 x 1/4 1.0SFQ-2-1/4 2-1/4 1/2 x 1/4 1.0SFQ-2-3/8 2-3/8 5/8 x 5/16 0.9
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
FLANGELESS QD BUSHINGSEQ BUSHINGS
EQ-MPB 7/8 MPB unsplit 4.1EQ-1-5/8 1-5/8 3/8 x 3/16 3.4EQ-1-7/8 1-7/8 1/2 x 1/4 3.1EQ-1-15/16 1-15/16 1/2 x 1/4 3.0EQ-2-1/8 2-1/8 1/2 x 1/4 2.9EQ-2-3/16 2-3/16 1/2 x 1/4 2.8EQ-2-1/4 2-1/4 1/2 x 1/4 2.7EQ-2-3/8 2-3/8 5/8 x 5/16 2.5EQ-2-7/16 2-7/16 5/8 x 5/16 2.4EQ-2-1/2 2-1/2 5/8 x 5/16 2.3EQ-2-3/4 2-3/4 5/8 x 5/16 2.0EQ-2-7/8 2-7/8 3/4 x 3/8 1.8
FQ BUSHINGSFQ-MPB 1 MPB unsplit 8.5FQ-1-5/8 1-5/8 3/8 x 3/16 7.5FQ-1-7/8 1-7/8 1/2 x 1/4 7.1FQ-1-15/16 1-15/16 1/2 x 1/4 7.0FQ-2-1/8 2-1/8 1/2 x 1/4 6.6FQ-2-3/8 2-3/8 5/8 x 5/16 6.2
Bushing Stock Approx.Part Bores Keyseat WeightNumber (in.) (lbs.)
FLANGELESS QD BUSHINGSFQ BUSHINGS
FQ-2-7/16 2-7/16 5/8 x 5/16 6.1FQ-2-1/2 2-1/2 5/8 x 5/16 5.9FQ-2-3/4 2-3/4 5/8 x 5/16 5.3FQ-2-7/8 2-7/8 3/4 x 3/8 4.9FQ-2-15/16 2-15/16 3/4 x 3/8 4.8FQ-3 3 3/4 x 3/8 4.6
Continued
QD Bushings Bore & Keyset DimensionsQD Bushings Bore & Keyset Dimensions
21
Standard Metric Key Approx.Bushing Bore Dimensions Weightpart No. (mm) (mm) (lbs.)
QT BUSHINGSstandard bushing with metric bore
QT-14MM 14 5 x 5 0.6QT-16MM 16 5 x 5 0.6QT-18MM 18 6 x 6 0.6QT-19MM 19 6 x 6 0.6QT-20MM 20 6 x 6 0.6QT-22MM 22 6 x 6 0.6QT-24MM 24 8 x 7 0.6QT-25MM 25 8 x 7 0.6QT-28MM 28 8 x 7 0.6QT-30MM 30 8 x 7 0.6QT-32MM 32 10 x 6 0.6QT-35MM 35 10 x 6 0.6QT-38MM 38 10 x 6 0.6
JA BUSHINGSstandard bushing with metric bore
JA-15MM 15 5 x 5 0.8JA-16MM 16 5 x 5 0.8JA-19MM 19 6 x 6 0.8JA-20MM 20 6 x 6 0.8JA-24MM 24 8 x 6 0.8JA-25MM 25 8 x 6 0.8JA-28MM 28 8 x 5 0.8
SH BUSHINGSstandard bushing with metric bore
SH-24MM 24 8 x 7 0.9SH-25MM 25 8 x 7 0.9SH-28MM 28 8 x 7 0.9SH-30MM 30 8 x 7 0.8SH-32MM 32 10 x 8 0.8SH-35MM 35 10 x 8 0.7
SDS BUSHINGSstandard bushing with metric bore
SDS-24MM 24 8 x 7 1.5SDS-25MM 25 8 x 7 1.5SDS-28MM 28 8 x 7 1.4SDS-30MM 30 8 x 7 1.4SDS-32MM 32 10 x 8 1.3SDS-35MM 35 10 x 8 1.2SDS-38MM 38 10 x 8 1.1SDS-40MM 40 12 x 8 1.1SDS-42MM 42 12 x 8 1.0
SD BUSHINGSstandard bushing with metric bore
SD-24MM 24 8 x 7 1.8SD-25MM 25 8 x 7 1.8SD-28MM 28 8 x 7 1.7SD-30MM 30 8 x 7 1.7SD-32MM 32 10 x 8 1.6SD-35MM 35 10 x 8 1.5SD-38MM 38 10 x 8 1.4SD-40MM 40 12 x 8 1.3SD-42MM 42 12 x 8 1.2
SK BUSHINGSstandard bushing with metric bore
SK-24MM 24 8 x 7 3.3SK-25MM 25 8 x 7 3.3
Standard Metric Key Approx.Bushing Bore Dimensions Weightpart No. (mm) (mm) (lbs.)
SK BUSHINGSstandard bushing with metric bore
SK-28MM 28 8 x 7 3.2SK-30MM 30 8 x 7 3.2SK-32MM 32 10 x 8 3.1SK-35MM 35 10 x 8 3.0SK-38MM 38 10 x 8 2.9SK-40MM 40 12 x 8 3.6SK-42MM 42 12 x 8 2.7SK-45MM 45 14 x 9 2.6SK-48MM 48 14 x 9 2.4SK-50MM 50 14 x 9 2.3SK-55M 55 16 x 10 2.0
SF BUSHINGSstandard bushing with metric bore
SF-28MM 28 8 x 7 4.7SF-30MM 30 8 x 7 4.6SF-32MM 32 10 x 8 4.5SF-35MM 35 10 x 8 4.4SF-38MM 38 10 x 8 4.2SF-40MM 40 12 x 8 4.2SF-42MM 42 12 x 8 4.1SF-45MM 45 14 x 9 3.9SF-48MM 48 14 x 9 3.7SF-50MM 50 14 x 9 3.6SF-55MM 55 16 x 10 3.2SF-60MM 60 18 x 11 3.0SF-65MM 65 18 x 8† 2.6
E BUSHINGS standard bushing with metric bore
E-35MM 35 10 x 8 10.2E-38MM 38 10 x 8 10.0E-40MM 40 12 x 8 9.9E-42MM 42 12 x 8 9.8E-45MM 45 14 x 9 9.6E-48MM 48 14 x 9 9.3E-50MM 50 14 x 9 9.2E-55MM 55 16 x 10 8.6E-60MM 60 18 x 11 8.1E-65MM 65 18 x 11 7.6E-70MM 70 20 x 12 7.1E-75MM 75 20 x 12 6.9E-80MM 80 22 x 11 6.3
F BUSHINGSstandard bushing with metric bore
F-45MM 45 14 x 9 16.2F-48MM 48 14 x 9 16.0F-50MM 50 14 x 9 15.8F-55MM 55 16 x 10 15.0F-60MM 60 18 x 11 14.3F-65MM 65 18 x 11 13.7F-70MM 70 20 x 12 12.9F-75MM 75 20 x 12 12.1F-80MM 80 22 x 14 11.2F-85MM 85 22 x 14 10.6F-90MM 90 25 x 14 9.7
Standard Metric Key Approx.Bushing Bore Dimensions Weightpart No. (mm) (mm) (lbs.)
J BUSHINGSstandard bushing with metric bore
J-50MM 50 14 x 9 26.5J-55MM 55 16 x 10 25.6J-60MM 60 18 x 11 24.7J-65MM 65 18 x 11 23.9J-70MM 70 20 x 12 23.0J-75MM 75 20 x 12 21.9J-80MM 80 22 x 14 20.9J-85MM 85 22 x 14 19.3J-90MM 90 25 x 14 18.1J-95MM 95 25 x 14 16.8J-100MM 100 28 x 16 16.5
M BUSHINGSstandard bushing with metric bore
M-80MM 80 22 x 14 55.0M-90MM 90 25 x 14 51.2M-100MM 100 28 x 16 46.9M-120MM 120 32 X 18 37.0
N BUSHINGSstandard bushing with metric bore
N-100MM 100 28 x 16 72.3N-120MM 120 32 X 18 60.2
P BUSHINGSstandard bushing with metric bore
P-150MM 150 36 X 20 95.8
The Metric system does not refer to keyseat or keyway dimensions as does the English system. Instead, dimensions aregiven for the key itself, which is rectangular in shape, not square as in the English system. This meets ISO standards.
METRIC
QD Bushings Bore & Keyset DimensionsQD Bushings Bore & Keyset Dimensions
22
This nomograph shows the maximum speed limit (in rpm) for a standard statically balancedsprocket of a given diameter and face width. To exceed this speed limit the sprocket should alsobe dynamically balanced.
To use, lay a staightedge between diameter and face width. Read maximum rpm recommendedfor standard balance where edge crosses slanted line. For faster speeds, dynamic balancing isrecommended.
EXAMPLE: If a 20 in. diameter x 5 in. (127 mm) face width sprocket runs faster than 1575 rpm,dynamic balancing is recommended.
NOTE: CAST IRON PRODUCTS CAN SAFELY OPERATE UP TO A MAXIMUM SPEED OF 6500 FEETPER MINUTE. SPROCKETS REQUIRED FOR FASTER SPEEDS MUST USE DUCTILE IRON WHICHHAS A MAXIMUM SAFE OPERATING SPEED OF 10,000 FEET PER MINUTE.
Graph 1
DIA
ME
TER
IN IN
CH
ES
FAC
E W
IDTH
– In
ches
and
Mill
imet
ers
MAXIMUM RPM RECOMMENDEDFOR STANDARD BALANCE
55
50
45
40
35
30
28
26
24
22
20
18
16
14
12
10
9
8
7
6
5
4
36322824
20181614
12
10
9
8
7
6
1335
4.5
1034
3.5
773
70
2.5
532
44
1.5
311.2
Inch
es
Mill
imet
ers
500
600
700
800
900
1000
1100
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3400
3800
4200
4400
4600
5000
3500
2900
1750
1460
725
640
860
960
1160
RPP PANTHER ULTRA-CORD SPROCKET Balancing Standards
23
RPP PANTHER ULTRA-CORD Drive Selection Procedure
SAFETY NOTE � WARNING!FAILURE TO FOLLOW RECOMMENDED APPLICATION INFORMATION AND RECOMMENDED PROCEDURESFOR INSTALLATION, CARE, MAINTENANCE AND STORAGE OF PRODUCTS MAY RESULT IN FAILURE TO PER-FORM PROPERLY AND MAY RESULT IN DAMAGE TO PROPERTY AND SERIOUS BODILY INJURY. MAKE SURETHAT PRODUCT SELECTED FOR ANY APPLICATION IS RECOMMENDED FOR THAT SERVICE.
RPP PANTHER BELT DRIVE SELECTION PROCEDURE
The selection of a stock RPP PANTHER belt drive is accomplished by completion of the following:A. Collection of basic drive data.B. Calculation of system design horsepower.C. Selection of belt pitch.D. Determination of belt length, sprocket diameters and center distance.E. Determination of required belt width.F. Determination of sprocket requirements.G. List selected material components.
A) Collection of Basic Drive Data: (use drive assistance data sheet, See Table of Contents)1A) DriveR: Type, power rating, rpm and shaft diameter.2A) DriveN: Type, power absorbed, rpm and shaft diameter. Does shock loading exist?3A) Service: Intermittent, periodic, or continuous.4A) Layout: Maximum sprocket widths and diameters, center distance, drive orientation and idler details.5A) Drive Orientation: Vertical or horizontal shafts.
6A) Drive Design Considerations:a) In most cases, the RPP PANTHER ULTRA-CORD belt will be considered in drive situations where its
significant increase in horsepower capacity allows the belt to be used in place of an extremely wide belt of lesser capacity or in situations where a chain would normally be utilized. For this reason, it is mandatory that RPP PANTHER ULTRA-CORD sprockets be used in conjunction with the belt to assure that the completedrive system consists of components of equal capacity. These sprockets are specifically designed dimensionally to enable proper meshing of the belt and sprocket and structurally to withstand the high load capacity of the belt.
b) In situations where speed-diameter combinations result in sprocket rim speeds above 6500 feet per minute,cast iron sprockets are not sufficient and special ductile iron sprockets must be used.
c) On all two-sprocket drives, the minimum flanging requirements are two flanges on one sprocket (normally thesmaller sprocket), or one flange on each sprocket on opposite sides. On vertical shaft applications, one sprocketshould be flanged on both sides and all other sprockets in the system flanged on the bottom if the sprocket axes parallelism cannot be held within 0.001 inches per inch of sprocket face width. On drives with more thantwo sprockets (including idlers), the minimum flanging requirements are two flanges on every other sprocket orone flange on each sprocket, alternating sides around the system.
d) Idlers can be used to clear obstructions, increase wrap, or to provide for installation and tensioning allowances on fixed center drives. They should be located in the slack belt span and can be on either the inside or backside of the belt. Inside idlers should be no smaller than the smallest load sprocket in thesystem. Inside idlers shall have the RPP PANTHER ULTRA-CORD Belt tooth profile unless they are larger in diameter than a 40 tooth sprocket. Flat inside idlers and all backside idlers should be flat and uncrowned. Backside idlers should be no less than 1.3 times the diameter of the smallest loaded sprocket in the system. To minimize tracking problems, the idler should be located nearest to the sprocket from which the belt is exiting.
24
A) Continued
EXAMPLE: 10 H.P. Nema B motor with an output speed of 1750 rpm is to drive a centrifugal pump at 1422 rpm. The center distance is approximately 17.5 inches. The service time is 14 hours per day at constant load.
DriveR = Nema B motor, 1-1/4 inch shaft diameter.P1 = 10 HP.n1 = 1750 rpm.
DriveN Machine = Centrifugal Pump, 1-1/2 inch shaft diameter.Minimal shock loading.P2 = Not known. (Assume 10 HP).n2 = 1422 rpm.
Service = 14 hours per day.Center distance = 17.5 inches.
B) Calculation of System Design Horsepower (Dhp)1B) Refer to DriveR (prime mover) table on page 25 to determine the class of the prime mover.
EXAMPLE: Class II
2B) Select the basic service factor (SF) from Basic Service Factors table on page 25 according to the type of driveN machine and class of motor.
EXAMPLE: SF = 1.4
3B) The corrected service factor is now obtained by adding or subtracting the following correction factors;
Cm = correction factor for speed up drives (See Additional Service Factor Speed-Up Drives table page 25.Cf = correction factor for operation conditions (see Additional Service Factor Operating Conditions table page 25).The corrected service factor (SFc) is then calculated as follows:
SFc = SF + Cm + Cf
EXAMPLE: SF = 1.4Cm = +0Cf = +0.2SFc = 1.4 + 0 + 0.2 = 1.6
4B) The Design horsepower (Dhp) is now obtained by multiplying the power to be transmitted by the corrected service factor.Dhp = P1 x SFc
EXAMPLE: Dhp = 10 x 1.6 = 16 DHP
RPP PANTHER ULTRA-CORD Drive Selection Procedure
25
DriveR (prime mover) RPP Panther ULTRA-CORDBasic Service Factors (SF) of driveN machines.Class of driveR Class I Class II Class III
Momentary Peak Load, 149% 150 to 250 to% of Rated Lead 249% 400%AC Electric Motors:Single Phase allSquirrel CageNEMA design A
3600 rpm 40 HP up 11⁄2 thru 30 HP1800 rpm 100 HP up 5 thru 75 HP 1 thru 3 HP1200 rpm 15 HP up 3⁄4 thru 10 HP900 rpm 5 HP up 1⁄2 thru 3 HP
NEMA design B3600 rpm 5 HP up 11⁄2 thru 3 HP1800 rpm 5 HP up 1 thru 3 HP1200 rpm 5 HP up 3⁄4 thru 3 HP900 rpm 2 HP up 1⁄2 thru 11⁄2 HP
NEMA design C1800 rpm 15 HP up 5 thru 10 HP1200 rpm 71⁄2 HP up 3 and 5 HP900 rpm all
NEMA design D allNEMA design F allWound Rotor
1800 rpm 20 HP 2 to 15 HP1200 rpm 15 HP 2 to 10 HP900 rpm 71⁄2 HP 1 to 5 HP
Synchronous normal torque high torqueDC Electric Motors shunt compound seriesEngines-int combust 8 cyl up 6 cyl 4 cyl or lessHydraulic Motors,Line Shaft all
ADDITIONAL SERVICE FACTORSPEED-UP DRIVES (Cm)
ADDITIONAL SERVICE FACTOROPERATING CONDITIONS (Cf)
Speed Additional Speed AdditionalRatio Service Ratio Service
Factor Factor
from 1 to 1.24 – from 2.50 to 3.50 +0.3
from 1.25 to 1.74 +0.1 over 3.50 +0.4
from 1.75 to 2.49 +0.2
Hours of Additional Hours of AdditionalOperation Service Operation Service
Factor Factor
Intermittent over 16 hoursor Seasonal -0.1 continuous +0.3
use per day
8 to 10 hourscontinuous +0.1 with idler +0.1use per day
10 to 16 hourscontinuous +0.2use per day
RPP PANTHER ULTRA-CORD Drive Selection Procedure
Class Class ClassdrlveN Machines I II IIIAgitators, Mixers Liquid 1.2 1.4 1.6(paddle or propeller) semi-liquid 1.3 1.5 1.7Bakery Machinery, Dough Mixers 1.2 1.4 1.6Brick and Clay Machinery
augers, mixers, granulators 1.4 1.6 1.8pug mills 1.6 1.8 2.0
Centrifuges 1.5 1.7 –Compressors reciprocating* 1.6 1.8 2.0
centrifugal 1.4 1.5 1.6Conveyors
belt, light package; oven 1.1 1.2 1.3belt: ore, coal, sand 1.2 1.4 1.6
apron, bucket, elevator, pan 1.4 1.6 1.8flight, screw 1.4 1.6 1.8
Fans, Blowers centrifugal, induceddraft exhausters 1.4 1.6 1.8
propeller, mine fans,positive blowers 1.6 1.8 2.0
Generators and Exciters 1.4 1.6 1.8Hammer Mills 1.5 1.7 1.9Hoists, Elevators 1.4 1.6 1.8Laundry Machinery general 1.2 1.4 1.6
extractors, washers 1.4 1.6 1.8Line Shafts 1.2 1.4 1.6Machine Tools drill presses,
lathes, screw machines 1.2 1.4 1.6boring mills, grinders 1.3 1.5 1.7
milling machines, shapers 1.3 1.5 1.7Mills ball, rod, pebble, etc. – 1.9 2.1Paper Machinery
agitators, calendars, dryers 1.2 1.4 1.6beaters, jordans, Nash pumps,
pulpers 1.4 1.6 1.8Printing Machinery
presses: newspaper, rotary, embossing, flat bed, magazine;
linotype machines; cutters; folders 1.4 1.4 1.6Pumps
centrifugal, gear, rotary, pipeline 1.2 1.4 1.6reciprocating* 1.7 1.9 2.1
Rubber Plant Machinery 1.4 1.6 1.8Saw Mill Machinery 1.4 1.6 1.8Screens vibrating (shakers) 1.3 1.5 –
drum, conical 1.2 1.4 –Textile Machinery
looms, spinning frames, twisters 1.3 1.5 1.7warpers, reels 1.2 1.4 –
Woodworking Machinerylathes, band saws 1.2 1.3 –
jointer, circular saws, planers 1.2 1.4
SAFETY NOTE � WARNING WHEN THE DRIVEN PULLEY IS USED AS A FLYWHEEL TO REDUCE SPEEDFLUCTUATIONS A SPECIALLY CONSTRUCTED PULLEY MAY BE REQUIRED.OBTAIN THE WR2 OF THE UNIT AND CONSULT ENGINEERING.
26
C) Selection of Belt Pitch
The correct belt pitch can be selected from Graph 2, using the design power (Dhp) obtained in step 4B and the rpm of the smaller sprocket (n1).
EXAMPLE: Dhp = 16 HP, n1 = 1750 rpm.Therefore Belt Pitch = 8mm.
RPP PANTHER ULTRA-CORD PITCH SELECTION CHARTDESIGN HORSEPOWER VERSUS RPM
RPP PANTHER ULTRA-CORD Drive Selection Procedure
NON-STANDARD
14MM
8MM
Graph 2
27
RPP PANTHER ULTRA-CORD Drive Selection Procedure
SAFETY NOTE � WARNING:USE ONLY RPP® PANTHER® ULTRA-CORD SPROCKETS. THEY ARE SPECIFICALLY DESIGNED TO HANDLETHE HIGH RATINGS IMPOSED BY THE RPP PANTHER ULTRA-CORD BELT.
D) Selection of Belts, Sprockets, and Center Distance
1D) Determine Speed Ratio (K) as follows:
K =n1n2
EXAMPLE: K =1750
= 1.231422
2D) Refer to the Center Distance Selection Table (on pages 46-63) for the selected belt pitch to determine which sprocket combinations give the desired speed ratio. The most suitable sprocket combination can then be selected as follows:
a) By examining the Horsepower Tables (on pages 37-45), eliminate any sprocket combinations which are not capable of transmitting the required power.
b) By examining the Center Distance Selection Table, eliminate any sprocket combination for which the required center distance cannot be obtained with a standard belt size.
iii) The final sprocket combination is then selected based upon the priorities required for the particular drive, in terms of flexibility in driven speed, center distance, drive cost etc...
EXAMPLE: DriveR Sprocket = 26 Teeth, DriveN Sprocket = 32 Teeth, Center Distance = 17.48 in. Belt Length = 1120 mm (140 Teeth), Belt Pitch = 8mm.
3D) Check that the ratio of the number of the teeth on the belt to the number of teeth on the sprocket is not a whole number. If this is the case alter the drive if possible, otherwise the belt life could be reduced.
EXAMPLE: Ratio is not a whole number.
140= 4.375
32
140= 5.385
26
28
4D) Determine the teeth in mesh factor (Cd).Determine the number of teeth in mesh on the smaller sprocket (nt) by using the following formula:
nt = [ 0.5 - (D-d) ] x n6L
where:L = Center distance (in.)n = Number of teeth on small sprocketD = Pitch diameter of large sprocket (in.)d = Pitch diameter of small sprocket (in.)
The number of teeth in mesh (nt) is then used to find the teeth in mesh factor (Cd).If nt is greater than six, then Cd = 1If nt is less than six, then the value of Cd must be obtained by consulting Teeth in Mesh Factors table on page 30.
EXAMPLE: nt = 12.85, therefore Cd = 1.0
E) Required Belt Width
1E) From the Horsepower Table the horsepower rating (Hp) for a particular belt pitch and width can be obtained by selecting the value corresponding to the number of teeth and the rpm of the smaller sprocket.
EXAMPLE: Z1 = 26 teeth, n1 = 1750 rpm. Therefore Hp = 23.53 (at 1750 rpm) for a belt width of 35mm
RPP PANTHER ULTRA-CORD Drive Selection Procedure
2E) Multiply the horsepower (Hp) for the belt by the belt length correction factor (KL - in Center Distance Selection tables pages 46-63), to obtain the actual power rating (Hpa) of the belt.
EXAMPLE: KL = 1.0, and Cd = 1.0; therefore Hpa = 23.526 x 1.0 x 1.0 = 23.526
3E) The final step is to calculate the actual drive system service factor (SFa).This is accomplished by comparing the original input motor horsepower (P1) from step A to the actual power rating of the selected belt (Hpa):
SFa = HpaP1
EXAMPLE: SFa = 23.526 = 2.3510
4E) The corrected service factor (SFc) in step 3B was equal to 1.6 while the actual service factor (SFa) is equal to 2.35. This positive comparison provides assurance that the drive design just completed exceeds the input requirements and should yield excellent durability.
F) Bushing Requirements:Determine bushing requirements to fit selected sprockets and shaft diameters as shown in the input data. Tables on pages 16 through 21, contain the necessary data for these determinations.
G) Selected Material Components:
EXAMPLE:DriveR sprocket = 26PTH8-35MPB (1 1/4 Bore)DriveN sprocket = 32PTH8-35QT (QT 1 1/2 Bushing)Belt = 1120PTH8M-35Center distance = 17.48”
RPP PANTHER ULTRA-CORD Drive Selection Procedure
29
30
RPP PANTHER ULTRA-CORD Drive Selection Procedure
Number of teeth (Cd)in Mesh
6 or more 1.00
5 0.80
4 0.60
3 0.40
2 0.20
TEETH IN MESH FACTORS (Cd) RPP PANTHER BELT LENGTHCORRECTION FACTORS (KL)
RPP PANTHER 8M RPP PANTHER 14M
LENGTH FACTOR LENGTH FACTOR(mm) (mm)
480 0.80 966 0.80
560 0.80 1190 0.80
600 0.80 1400 0.90
640 0.90 1610 0.90
720 0.90 1778 0.95
800 0.90 1890 0.95
880 0.90 2100 1.00
960 1.00 2310 1.00
1040 1.00 2450 1.05
1120 1.00 2590 1.05
1152 1.00 2800 1.10
1200 1.00 3150 1.10
1224 1.00 3360 1.15
1280 1.10 3500 1.15
1440 1.10 3850 1.20
1600 1.10 4326 1.20
1760 1.20 4578 1.25
1800 1.20 4956 1.25
2000 1.20
2200 1.20
2400 1.30
2600 1.30
2800 1.40
3048 1.40
3280 1.40
3600 1.50
4400 1.50
INSTALLATION AND TENSIONING ALLOWANCESCenter distance allowances for an RPP PANTHER ULTRA-CORD Belt drive are necessary to assure that the belt can beinstalled without damage and then tensioned correctly. The standard installation allowance is defined as the minimumdecrease in center distance required to install a belt when the flanged sprocket is removed from the shaft for belt installa-tion. This value is shown in the second column of Table 13. If this minimum value is not available consult Engineering fordesign consultation. This table also lists the minimum increase in center distance required to assure that a belt can beproperly tensioned.
The shortest center distance for each sprocket combination (Center Distance Selection tables), may not fully accommodatethe values in Table 13 due to potential sprocket interference.
If a belt is to be installed over flanged sprockets without removing the sprockets, the additional center distance allowancenecessary for installation is shown in Table 14. This value must be added to the allowance shown in Table 13.
DRIVE INSTALLATION AND ALIGNMENT
Table 13 - Center Distance Allowance Table 14 - Additional Center DistanceFor Installation and Tensioning Allowance
Reduce the center distance by the amount shown in Tables 13 and 14 or change the idler position so that the belt can bepositioned on the drive with ease. When installing the belt, never force it over the sprocket flange. If necessary, removethe smaller sprocket from the shaft.
NOTE: RPP PANTHER ULTRA-CORD belts are constructed to attain proper pitch dimension when subjected to tension.For this reason, the belt may not fully engage in large diameter sprockets without applying tension to the belt.Shafts must be correctly aligned (parallel). Misalignment causes uneven pressure on the teeth of the belt, uneven loadingof the tensile member and extreme edge wear on the belt which can result in premature belt failure.
Sprocket axes must be aligned and alignment maintained to prevent the belt from riding against the flanges or over theedge of the flangeless sprocket. The mounting attachments of the driveR and driveN should be rigid enough to preventchanges in sprocket alignment or drive center distance as the load is applied to the drive.
Mounting procedures, which are included with sprockets and associated bushings, should be followed to insure propermounting. Bushings are easy to install and remove. They are the split through flange and taper design which provides atrue clamp on the shaft that is essentially equivalent to a shrink fit. Bushings have a very gradual taper (3/4 inch taper perft. on the diameter). The result is that it securely clamps the shaft with extreme holding power.
NOTE:Care should be taken to use no lubrication on the shaft, sprocket or bushing in order to prevent possible slipping on theshaft or possible bursting of the sprocket through excessive force created by the taper of the bushing. Also, cap screwtorque limitations should be adhered to in order to prevent damage.
31
For Installation Over Flanged Sprockets (Add to Installation Allowance in Table 13)
Sprocket Additional Allowance if BothPitch Small Sprocket is the only Sprocket
Flanged Sprocket Flanged(in.) (in.)
8mm 0.60 1.2014mm 0.90 2.10
Belt Pitch Standard installation RequiredLength Range Allowance (Flanged Tensioning
(in.) Sprockets Removed AllowanceFor Installation) (Any Drive)
(in.) (in.)
0 - 30 0.070 0.03031 - 60 0.110 0.03561 - 110 0.130 0.040111 - 160 0.160 0.045161 - 200 0.190 0.050
RPP PANTHER ULTRA-CORD Installation & Tensioning
32
TENSIONING PROCEDUREWhen installing a RPP PANTHER belt, the belt tension is chosen so as to avoid the problems listed below:
i) TOOTH JUMPAssure that the belt is tensioned adequately to prevent tooth jump under the most severe load conditions that the drive will encounter.
ii) EXTREMELY HIGH BELT TENSIONAvoid extremely high tension which results in elevated noise levels and reduced belt and bearing life.
METHOD 1: STANDARD RPP PANTHER BELT INSTALLATION AND TENSIONING PROCEDURE
The procedure for determining the correct belt tension, is as follows:
A. Calculate the installation tension (Ts).B. Calculate the nominal deflection force (Fnom).C. Calculate or measure the free span length (t).D. Determine the deflection distance (def).E. Measure the actual deflection force (Fact).F. Compare the actual deflection force (Fact) to the calculated nominal deflection force (Fnom).
The application of the installation tension is based on measuring the force required to deflect one span ofthe belt by a given amount as shown in Figure 7 below. Completion of steps A through F are necessary tocomplete proper tensioning.
A - Installation TensionCalculate the installation tension (Ts) using the following formula:
Ts (lbs) = 81938 * HPDia. * RPM
Where: HP= Motor base horsepower.Dia. = DriveR sprocket pitch diameter (inches).RPM = DriveR sprocket speed.BW = Belt Width (mm).Mass = Mass Factor (Obtained from Table 16).
Note: Ts must be compared with the minimums listed in Table 15
Table 15 – Minimum installation tensions
Table 16 – Mass Factors
RPP PANTHER ULTRA-CORD Installation & Tensioning
SPAN LENGTH
DEFLECTION FORCE
DEFLECTION
EXAMPLE:
Ts (lbs) = 81938 * 10 2.607 * 1750
Ts (lbs) = 181.3 Lbs
The calculated Ts of 181.3 lbs is greater than the minimum of 101lbs obtained from the 8mm Pitch – 35mm width section of Table 15,so Ts will remain 181.3 lbs.
+ 4.399X10-7 * BW * Mass * Dia.2 * RPM2
Pitch Width Min Ts
8mm 12mm 3022mm 6035mm 10160mm 187
14mm 20mm 7742mm 18065mm 29690mm 429120mm 595
Pitch Mass Factor8mm 0.00525
14mm 0.01030
+ 4.399X10-7 * 35 * 0.00525 * 2.6072 * 17502
Figure 7
33
RPP PANTHER ULTRA-CORD Installation & Tensioning
B - Nominal Deflection Force
Calculate the nominal deflection force (Fnom) required to attain the above installation tension (Ts):
Fnom (lbs) = Ts16
EXAMPLE: 181.3 = 11.3 lbs16
C - Free Span Length
Calculate the free span length (t) of the belt. This value can be determined by:
t (in) = L2 - (D-d)2
2
Where: L = Center distance (inches)D = Pitch diameter of large sprocket (inches)d = Pitch diameter of small sprocket (inches)
t (in) = (17.48)2 - (3.208 - 2.607)2
t = 17.477 inches
D - Deflection Distance
Determine the deflection distance by:def (in) = 0.0156 (t).Where (t) = free span length (inches).
EXAMPLE: def (in) = 0.0156 x 17.477def (in) = 0.27 inches
E - Measure Actual Deflection Force
With the belt installed on the drive and tensioned to a level required to eliminate all slack in the system (snug fit)begin the tensioning procedure. At the center of the belt span to be tensioned, apply a force equal to the deflectionforce calculated previously in step B. This force is applied perpendicular to the span so as to deflect the belt by theamount equal to (def) calculated in step D. For belts wider than 2.0 inches, place a section of rigid member (such askey stock) across the belt width to prevent belt distortion and insure proper tensioning. Be sure that either the driveRor driveN sprocket is free to rotate.
F - Deflection Force Comparison
Compare the actual force (Fact) necessary to deflect the installed belt at the center of the free span by theamount calculated in step B. If the measured force (Fact) is greater than 1.10 times the calculated force (Fnom),the belt is too tight. If the measured force (Fact) is less than 0.90 times the calculated force (Fnom), the belt istoo loose. In both cases a tension adjustment is necessary.
EXAMPLE:2
34
RPP PANTHER ULTRA-CORD Installation & Tensioning
METHOD 2: SIMPLIFIED RPP PANTHER BELT INSTALLATION AND TENSIONING PROCEDURE
Table 17 presents the nominal center distance and take up allowance required to install and tension RPP PANTHER belts under the following conditions.
Condition A - one flanged sprocket and one unflanged sprocket. When sprockets have been mounted and properly aligned, put belt over flanged sprocket first, then slip it onto the unflanged sprocket. As indicated before,in that RPP PANTHER belts are designed to transmit extremely high loads, the complete engagement of the beltin large diameter sprockets may require the application of tension during installation. Tension belt by adjustingcenter distance or by using an idler if center distance is fixed.
Condition B - both sprockets flanged. Put belt over larger sprocket first, then over smaller sprocket. Tension beltby adjusting centers or by adjusting tensioning idler.
Condition C - minimal center distance adjustment. Mount one sprocket on shaft loosely and put belt on sprock-et. Put other sprocket into belt loop and slip the sprocket onto the other shaft. Move whole drive into proper posi-tion and alignment and secure sprocket to shafts. Tension belt by adjusting center distance.Less allowance for installation and take-up may be possible. This can be determined by a summation of require-ments in Tables 13 and 14, page 20
NOTE: DO NOT PRY OR OTHERWISE FORCE BELTS ONTO SPROCKETS AS THIS CAN RESULT IN PERMANENTDAMAGE TO THE BELT.
Table 17 - CENTER DISTANCE ALLOWANCE
NOTE: For drives with shock loadingor other unusual conditions, the force may have to be increased for proper operation of the drive.
BELT TENSION
RPP PANTHER Belt Drives do not require as much tension as other belt drives that depend on friction to trans-mit the load. The installation procedure should begin by installing the RPP PANTHER Belt with a snug fit, neithertoo tight nor too loose. After the belt has been so tensioned, a force to deflect the belt by a certain amount toassure proper tension can be measured. Measure the belt span (t) as shown in Figure 7. With one sprocket freeto rotate, use a spring scale to apply a perpendicular force to the center of the belt width at the mid-point of thebelt span. For belts wider than 2”, it is suggested that a strip of keystock, or something similar, be placed acrossthe belt under the point of force to prevent distortion.
Measure the force required to deflect the belt 1/64” for each inch of belt span. For example, the deflection for a32” belt span is 32 x 1/64 = 1/2” deflection. The force required to deflect the belt this amount at the proper ten-sion is listed in Average Tensioning Values tables on pages 35 and 36.
NOTE: Utilization of the simplified tension procedure (Method 2) may not result in ultimate belt life due to deflection forces in Average Tensioning Values table being less accurate than the nominal deflection force calculated in Method 1.
Belt AllowancePitch Allowance for Installation For
Length Condition Take UpA B C
Range 8mm 14mm 8mm 14mm 8mm&14mm 8mm & 14mm(Inches) Belts Belts Belts Belts Belts Belts
Up to 60” .7” 1.0” 1.2” 2.2” .1” .1”61 to 110” .8” 1.1” 1.3” 2.3” .2” .2”over 110” .9” 1.2” 1.4” 2.4” .3” .3”
35
TW = 12 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 116 515 105 467 7 7> 100 to 500 88 390 80 355 5 5> 500 to 1000 80 355 73 323 5 5> 1001 to 1500 73 323 66 294 5 4 > 1500 to 2000 68 302 62 275 4 4> 2000 61 270 55 246 4 3
TW = 22 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 212 944 193 856 13 12> 100 to 500 161 714 146 651 10 9> 500 to 1000 146 651 133 592 9 8> 1001 to 1500 133 592 121 538 8 8> 1500 to 2000 124 553 113 504 8 7> 2000 111 494 101 450 7 6
TW = 35 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 338 1502 306 1362 21 19> 100 to 500 256 1137 233 1035 16 15> 500 to 1000 233 1035 212 942 15 13> 1001 to 1500 212 942 193 856 13 12> 1500 to 2000 198 880 180 802 12 11> 2000 177 786 161 716 11 10
TW = 60 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 579 2576 525 2335 36 33> 100 to 500 438 1948 399 1775 27 25> 500 to 1000 399 1775 363 1615 25 23> 1001 to 1500 363 1615 330 1468 23 21> 1500 to 2000 339 1508 309 1375 21 19> 2000 303 1348 276 1228 19 17
RPP PANTHER ULTRA-CORD Installation & Tensioning
8M Panther
With ULTRA-CORD StrandAverage Tensioning Values
36
TW = 20 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 500 2224 455 2022 31 28> 100 to 500 430 1911 390 1737 27 24> 500 to 1000 400 1779 364 1618 25 23> 1001 to 1500 361 1605 328 1460 23 21> 1500 to 2000 333 1482 303 1348 21 19> 2000 293 1304 267 1187 18 17
TW = 42 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 1050 4671 955 4246 66 60> 100 to 500 902 4012 820 3647 56 51> 500 to 1000 840 3737 764 3397 53 48> 1001 to 1500 758 3371 689 3066 47 43> 1500 to 2000 700 3112 636 2830 44 40> 2000 616 2739 560 2492 38 35
TW = 65 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 1625 7228 1477 6571 102 92> 100 to 500 1396 6210 1269 5645 87 79> 500 to 1000 1300 5783 1182 5257 81 74> 1001 to 1500 1173 5218 1067 4744 73 67> 1500 to 2000 1083 4817 985 4380 68 62> 2000 953 4238 867 3857 60 54
TW = 90 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 2250 10008 2045 9099 141 128> 100 to 500 1933 8598 1757 7816 121 110> 500 to 1000 1800 8007 1636 7279 113 102> 1001 to 1500 1624 7224 1477 6569 102 92> 1500 to 2000 1499 6669 1363 6064 94 85> 2000 1319 5869 1201 5341 82 75
TW = 120 mm Strand Tensionnew belts used belts Deflection Force (lbf)
RPM lbf Newtons lbf Newtons new belts used belts<=100 3000 13345 2727 12132 188 170> 100 to 500 2577 11464 2343 10421 161 146> 500 to 1000 2400 10676 2182 9705 150 136> 1001 to 1500 2165 9632 1969 8759 135 123>1500 to 2000 1999 8892 1818 8086 125 114>2000 1759 7825 1601 7121 110 100
14M Panther
RPP PANTHER ULTRA-CORD Installation & Tensioning
With ULTRA-CORD StrandAverage Tensioning Values
37
BELT HORSEPOWER RATINGS12mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
NOTE: FOR SPROCKET SPEEDS ABOVE 5000 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 8mm Horsepower Tables
SmallestSprocketRpm
12mm (.472 in.) wide belt (PTH8M-12)
No. Teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80
P.D. (mm) 56.02 61.12 66.21 71.30 76.39 81.49 86.58 91.67 96.77 101.86 112.05 122.23 142.60 162.97 183.35 203.72
P.D. (in) 2.206 2.406 2.607 2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020
RPM HORSEPOWER RATING (Hp)
870 3.92 4.31 4.70 5.09 5.48 5.88 6.27 6.67 7.07 7.48 8.28 9.10 10.74 12.39 14.06 15.74
1160 4.90 5.38 5.87 6.36 6.85 7.34 7.83 8.33 8.83 9.33 10.34 11.35 13.39 15.44 17.51 19.58
1750 6.73 7.39 8.06 8.72 9.39 10.07 10.74 11.42 12.10 12.78 14.15 15.52 18.27 21.02 23.77 26.51
3450 11.31 12.40 13.49 14.59 15.68 16.77 17.86 18.95 20.04 21.11 23.26 25.37 29.50 33.47
10 0.07 0.07 0.08 0.09 0.09 0.10 0.10 0.11 0.12 0.12 0.14 0.15 0.18 0.20 0.23 0.26
20 0.13 0.14 0.15 0.16 0.17 0.19 0.20 0.21 0.22 0.24 0.26 0.28 0.33 0.39 0.44 0.49
30 0.18 0.20 0.22 0.24 0.25 0.27 0.29 0.31 0.32 0.34 0.38 0.41 0.49 0.56 0.63 0.71
50 0.29 0.32 0.35 0.38 0.40 0.43 0.46 0.49 0.52 0.55 0.60 0.66 0.78 0.89 1.01 1.13
70 0.40 0.44 0.47 0.51 0.55 0.59 0.63 0.67 0.71 0.74 0.82 0.90 1.06 1.22 1.38 1.54
100 0.55 0.61 0.66 0.71 0.76 0.82 0.87 0.93 0.98 1.03 1.14 1.25 1.47 1.69 1.92 2.14
200 1.05 1.15 1.25 1.35 1.45 1.55 1.65 1.75 1.85 1.96 2.16 2.37 2.78 3.20 3.62 4.05
300 1.52 1.66 1.81 1.95 2.10 2.25 2.40 2.54 2.69 2.84 3.14 3.44 4.04 4.65 5.26 5.88
400 1.98 2.17 2.36 2.55 2.74 2.93 3.12 3.31 3.51 3.70 4.09 4.48 5.27 6.06 6.85 7.65
500 2.43 2.66 2.89 3.13 3.36 3.60 3.83 4.07 4.31 4.54 5.02 5.50 6.47 7.44 8.41 9.39
600 2.87 3.15 3.42 3.70 3.97 4.25 4.53 4.81 5.09 5.37 5.94 6.51 7.64 8.79 9.94 11.10
700 3.31 3.63 3.94 4.26 4.58 4.90 5.22 5.54 5.87 6.19 6.84 7.49 8.81 10.13 11.45 12.78
800 3.74 4.10 4.46 4.82 5.18 5.54 5.90 6.27 6.63 7.00 7.73 8.47 9.95 11.44 12.94 14.44
900 4.03 4.42 4.82 5.22 5.63 6.03 6.44 6.85 7.26 7.67 8.50 9.34 11.02 12.72 14.43 16.15
1000 4.37 4.80 5.23 5.67 6.11 6.55 6.99 7.43 7.88 8.32 9.22 10.13 11.95 13.79 15.64 17.50
1100 4.70 5.17 5.63 6.10 6.57 7.05 7.52 8.00 8.48 8.96 9.92 10.90 12.85 14.83 16.82 18.81
1200 5.03 5.53 6.02 6.53 7.03 7.53 8.04 8.55 9.06 9.58 10.61 11.65 13.74 15.84 17.96 20.08
1300 5.35 5.88 6.41 6.94 7.48 8.01 8.55 9.10 9.64 10.19 11.28 12.38 14.60 16.83 19.08 21.32
1400 5.67 6.23 6.79 7.35 7.91 8.48 9.05 9.63 10.20 10.78 11.94 13.10 15.45 17.80 20.16 22.53
1500 5.98 6.57 7.16 7.75 8.35 8.95 9.55 10.15 10.76 11.36 12.59 13.81 16.27 18.75 21.23 23.71
1600 6.28 6.90 7.52 8.14 8.77 9.40 10.03 10.67 11.30 11.94 13.22 14.50 17.08 19.67 22.26 24.85
1700 6.58 7.23 7.88 8.53 9.19 9.85 10.51 11.17 11.84 12.50 13.84 15.18 17.88 20.58 23.28 25.97
1800 6.88 7.56 8.23 8.92 9.60 10.29 10.98 11.67 12.36 13.06 14.45 15.85 18.66 21.46 24.27 27.05
1900 7.17 7.88 8.58 9.29 10.00 10.72 11.44 12.16 12.88 13.60 15.06 16.51 19.42 22.33 25.23 28.11
2000 7.46 8.19 8.93 9.66 10.40 11.15 11.89 12.64 13.39 14.14 15.65 17.15 20.17 23.18 26.17 29.14
2500 8.85 9.72 10.59 11.46 12.33 13.20 14.08 14.96 15.84 16.71 18.47 20.22 23.71 27.15 30.54 33.85
3000 10.17 11.16 12.15 13.14 14.14 15.13 16.13 17.12 18.12 19.11 21.08 23.04 26.91 30.68 34.33 37.83
3500 11.43 12.53 13.64 14.74 15.85 16.95 18.05 19.15 20.24 21.33 23.49 25.62 29.77 33.75
4000 12.63 13.84 15.05 16.26 17.46 18.66 19.86 21.04 22.22 23.39 25.70 27.95 32.29
4500 13.78 15.09 16.40 17.70 18.99 20.27 21.55 22.81 24.06 25.29 27.70 30.04
5000 14.89 16.29 17.68 19.06 20.43 21.78 23.12 24.44 25.74 27.02 29.50 31.87
BELT HORSEPOWER RATINGS22mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
38
NOTE: FOR SPROCKET SPEEDS ABOVE 5000 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 8mm Horsepower Tables
22 mm (0.866 in.) wide belt (PTH8M-22)
No. Teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80
P.D. (mm) 56.02 61.12 66.21 71.30 76.39 81.49 86.58 91.67 96.77 101.86 112.05 122.23 142.60 162.97 183.35 203.72
P.D. (in) 2.206 2.406 2.607 2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020
RPM HORSEPOWER RATING (Hp)
870 7.20 7.91 8.62 9.34 10.06 10.78 11.51 12.24 12.98 13.72 15.20 16.69 19.70 22.74 25.80 28.88
1160 8.99 9.88 10.77 11.66 12.56 13.47 14.37 15.29 16.20 17.12 18.97 20.82 24.56 28.33 32.12 35.92
1750 12.35 13.57 14.78 16.01 17.24 18.47 19.71 20.95 22.20 23.45 25.96 28.47 33.52 38.57 43.62 48.65
3450 20.74 22.75 24.76 26.76 28.77 30.78 32.78 34.77 36.76 38.74 42.67 46.55 54.13 61.40
10 0.12 0.13 0.15 0.16 0.17 0.18 0.19 0.20 0.22 0.23 0.25 0.28 0.32 0.37 0.42 0.47
20 0.23 0.25 0.27 0.30 0.32 0.34 0.36 0.39 0.41 0.43 0.48 0.52 0.61 0.71 0.80 0.89
30 0.33 0.37 0.40 0.43 0.46 0.50 0.53 0.56 0.59 0.63 0.69 0.76 0.89 1.03 1.16 1.30
50 0.54 0.59 0.64 0.69 0.74 0.79 0.85 0.90 0.95 1.00 1.11 1.21 1.43 1.64 1.86 2.08
70 0.73 0.80 0.87 0.94 1.01 1.08 1.15 1.22 1.30 1.37 1.51 1.65 1.95 2.24 2.53 2.83
100 1.01 1.11 1.21 1.31 1.40 1.50 1.60 1.70 1.80 1.90 2.10 2.30 2.70 3.11 3.52 3.93
200 1.92 2.10 2.29 2.47 2.65 2.84 3.03 3.21 3.40 3.59 3.97 4.35 5.11 5.88 6.65 7.43
300 2.78 3.05 3.32 3.59 3.86 4.13 4.40 4.67 4.94 5.21 5.76 6.31 7.42 8.53 9.66 10.78
400 3.63 3.98 4.32 4.67 5.02 5.38 5.73 6.08 6.44 6.79 7.51 8.22 9.66 11.12 12.58 14.04
500 4.45 4.88 5.31 5.74 6.17 6.60 7.03 7.47 7.90 8.34 9.22 10.09 11.86 13.64 15.44 17.24
600 5.27 5.77 6.28 6.78 7.29 7.80 8.32 8.83 9.34 9.86 10.90 11.94 14.03 16.13 18.25 20.37
700 6.07 6.65 7.23 7.82 8.40 8.99 9.58 10.17 10.77 11.36 12.55 13.75 16.16 18.58 21.01 23.45
800 6.86 7.52 8.18 8.84 9.50 10.17 10.83 11.50 12.17 12.84 14.19 15.54 18.26 20.99 23.74 26.50
900 7.39 8.12 8.85 9.59 10.33 11.07 11.82 12.57 13.32 14.08 15.60 17.13 20.22 23.34 26.48 29.64
1000 8.02 8.81 9.60 10.40 11.20 12.01 12.82 13.63 14.45 15.27 16.92 18.58 21.92 25.30 28.70 32.11
1100 8.63 9.48 10.34 11.19 12.06 12.93 13.80 14.67 15.55 16.44 18.21 19.99 23.59 27.21 30.85 34.51
1200 9.23 10.14 11.05 11.97 12.89 13.82 14.76 15.69 16.63 17.57 19.47 21.37 25.21 29.07 32.95 36.85
1300 9.82 10.79 11.76 12.73 13.72 14.70 15.69 16.69 17.69 18.69 20.70 22.72 26.79 30.89 35.00 39.12
1400 10.40 11.42 12.45 13.48 14.52 15.57 16.61 17.66 18.72 19.78 21.91 24.04 28.34 32.66 37.00 41.34
1500 10.97 12.05 13.13 14.22 15.31 16.41 17.52 18.62 19.74 20.85 23.09 25.34 29.86 34.40 38.95 43.49
1600 11.53 12.66 13.80 14.94 16.09 17.25 18.41 19.57 20.74 21.90 24.25 26.61 31.34 36.09 40.85 45.60
1700 12.08 13.27 14.46 15.65 16.86 18.07 19.28 20.50 21.72 22.94 25.40 27.86 32.80 37.76 42.71 47.64
1800 12.62 13.86 15.11 16.36 17.61 18.88 20.14 21.41 22.68 23.96 26.52 29.08 34.23 39.38 44.52 49.64
1900 13.16 14.45 15.75 17.05 18.36 19.67 20.99 22.31 23.63 24.96 27.62 30.29 35.63 40.97 46.29 51.58
2000 13.69 15.03 16.38 17.73 19.09 20.46 21.82 23.19 24.57 25.95 28.71 31.47 37.01 42.53 48.02 53.46
2500 16.24 17.83 19.42 21.02 22.62 24.23 25.83 27.44 29.06 30.67 33.89 37.10 43.50 49.82 56.04 62.11
3000 18.66 20.48 22.30 24.12 25.94 27.77 29.59 31.41 33.24 35.05 38.68 42.28 49.37 56.29 62.99 69.41
3500 20.97 23.00 25.02 27.05 29.07 31.10 33.12 35.13 37.14 39.13 43.10 47.00 54.63 61.93
4000 23.18 25.40 27.62 29.83 32.04 34.24 36.43 38.61 40.77 42.92 47.15 51.29 59.25
4500 25.29 27.69 30.09 32.47 34.84 37.20 39.53 41.84 44.14 46.40 50.83 55.12
5000 27.31 29.88 32.44 34.97 37.48 39.97 42.42 44.84 47.23 49.57 54.13 58.48
SmallestSprocketRpm
BELT HORSEPOWER RATINGS35mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
39
NOTE: FOR SPROCKET SPEEDS ABOVE 5000 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 8mm Horsepower Tables
SmallestSprocketRpm
35 mm (1.377 in.) wide belt (PTH8M-35)
No. Teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80
P.D. (mm) 56.02 61.12 66.21 71.30 76.39 81.49 86.58 91.67 96.77 101.86 112.05 122.23 142.60 162.97 183.35 203.72
P.D. (in) 2.206 2.406 2.607 2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020
RPM HORSEPOWER RATING (Hp)
870 11.46 12.59 13.72 14.86 16.01 17.16 18.32 19.49 20.66 21.83 24.19 26.56 31.35 36.19 41.06 45.97
1160 14.31 15.72 17.14 18.56 19.99 21.43 22.88 24.33 25.79 27.25 30.19 33.14 39.09 45.08 51.12 57.17
1750 19.66 21.59 23.53 25.47 27.43 29.40 31.37 33.35 35.33 37.32 41.31 45.31 53.35 61.39 69.42 77.42
3450 33.01 36.21 39.40 42.59 45.78 48.98 52.16 55.34 58.50 61.65 67.91 74.09 86.15 97.72
10 0.19 0.21 0.23 0.25 0.27 0.29 0.31 0.33 0.34 0.36 0.40 0.44 0.52 0.59 0.67 0.75
20 0.37 0.40 0.44 0.47 0.51 0.54 0.58 0.62 0.65 0.69 0.76 0.83 0.98 1.12 1.27 1.42
30 0.53 0.58 0.63 0.69 0.74 0.79 0.84 0.89 0.95 1.00 1.10 1.21 1.42 1.63 1.85 2.06
50 0.85 0.93 1.02 1.10 1.18 1.26 1.35 1.43 1.51 1.60 1.76 1.93 2.27 2.61 2.96 3.30
70 1.16 1.27 1.38 1.50 1.61 1.72 1.83 1.95 2.06 2.18 2.40 2.63 3.10 3.56 4.03 4.50
100 1.61 1.77 1.92 2.08 2.23 2.39 2.55 2.70 2.86 3.02 3.34 3.66 4.30 4.94 5.59 6.25
200 3.05 3.34 3.64 3.93 4.23 4.52 4.82 5.12 5.41 5.71 6.31 6.92 8.13 9.35 10.58 11.82
300 4.43 4.86 5.28 5.71 6.14 6.57 7.00 7.43 7.86 8.30 9.17 10.04 11.81 13.58 15.37 17.16
400 5.77 6.33 6.88 7.44 7.99 8.55 9.12 9.68 10.24 10.81 11.95 13.09 15.38 17.69 20.02 22.35
500 7.09 7.77 8.45 9.13 9.81 10.50 11.19 11.88 12.58 13.27 14.67 16.06 18.88 21.71 24.57 27.43
600 8.38 9.19 9.99 10.80 11.61 12.42 13.23 14.05 14.87 15.69 17.34 18.99 22.32 25.67 29.04 32.42
700 9.66 10.58 11.51 12.44 13.37 14.31 15.25 16.19 17.13 18.08 19.98 21.88 25.71 29.57 33.44 37.33
800 10.92 11.97 13.01 14.06 15.12 16.18 17.24 18.30 19.37 20.44 22.58 24.73 29.06 33.41 37.78 42.17
900 11.76 12.92 14.08 15.26 16.43 17.62 18.81 20.00 21.20 22.41 24.83 27.27 32.18 37.14 42.14 47.17
1000 12.76 14.02 15.28 16.55 17.83 19.11 20.40 21.70 23.00 24.30 26.93 29.57 34.89 40.26 45.67 51.10
1100 13.74 15.09 16.45 17.81 19.19 20.57 21.96 23.35 24.75 26.16 28.98 31.82 37.53 43.30 49.10 54.93
1200 14.69 16.14 17.59 19.05 20.52 22.00 23.48 24.97 26.47 27.97 30.98 34.01 40.11 46.26 52.44 58.64
1300 15.63 17.17 18.71 20.27 21.83 23.40 24.97 26.56 28.15 29.74 32.94 36.16 42.63 49.15 55.70 62.26
1400 16.55 18.18 19.81 21.46 23.11 24.77 26.44 28.11 29.79 31.48 34.86 38.26 45.10 51.98 58.88 65.79
1500 17.45 19.17 20.90 22.63 24.37 26.12 27.88 29.64 31.41 33.18 36.75 40.32 47.52 54.74 61.98 69.22
1600 18.35 20.15 21.96 23.78 25.61 27.45 29.29 31.14 33.00 34.86 38.60 42.35 49.88 57.44 65.01 72.56
1700 19.22 21.11 23.01 24.91 26.83 28.75 30.68 32.62 34.56 36.51 40.42 44.33 52.20 60.09 67.97 75.82
1800 20.09 22.06 24.04 26.03 28.03 30.04 32.05 34.07 36.10 38.13 42.20 46.29 54.48 62.67 70.86 78.99
1900 20.94 23.00 25.06 27.13 29.21 31.31 33.40 35.50 37.61 39.72 43.96 48.20 56.71 65.21 73.68 82.08
2000 21.78 23.92 26.07 28.22 30.38 32.55 34.73 36.91 39.10 41.29 45.69 50.09 58.90 67.68 76.43 85.09
2500 25.85 28.38 30.91 33.45 36.00 38.55 41.11 43.67 46.24 48.80 53.93 59.05 69.23 79.29 89.18 98.85
3000 29.70 32.59 35.48 38.38 41.28 44.19 47.09 49.99 52.89 55.79 61.56 67.28 78.57 89.59 100.25 110.47
3500 33.37 36.60 39.82 43.05 46.27 49.50 52.71 55.91 59.11 62.28 68.59 74.81 86.94 98.56
4000 36.88 40.42 43.95 47.48 50.99 54.50 57.98 61.44 64.89 68.30 75.04 81.63 94.30
4500 40.25 44.07 47.88 51.68 55.45 59.20 62.92 66.59 70.24 73.84 80.90 87.72
5000 43.47 47.56 51.62 55.65 59.65 63.61 67.51 71.37 75.17 78.89 86.14 93.07
40
60 mm (2.362 in.) wide belt (PTH8M-60)
No. Teeth 22 24 26 28 30 32 34 36 38 40 44 48 56 64 72 80
P.D. (mm) 56.02 61.12 66.21 71.30 76.39 81.49 86.58 91.67 96.77 101.86 112.05 122.23 142.60 162.97 183.35 203.72
P.D. (in) 2.206 2.406 2.607 2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020
RPM HORSEPOWER RATING (Hp)
870 19.64 21.58 23.52 25.48 27.45 29.43 31.42 33.41 35.42 37.43 41.48 45.55 53.76 62.05 70.41 78.82
1160 24.54 26.96 29.38 31.83 34.28 36.75 39.23 41.71 44.21 46.72 51.76 56.82 67.03 77.31 87.65 98.03
1750 33.71 37.02 40.34 43.68 47.04 50.41 53.79 57.18 60.59 64.00 70.84 77.70 91.47 105.26 119.04 132.75
3450 56.61 62.09 67.56 73.03 78.51 83.99 89.44 94.88 100.32 105.72 116.45 127.03 147.72 167.57
10 0.33 0.36 0.40 0.43 0.46 0.49 0.52 0.56 0.59 0.62 0.69 0.75 0.89 1.02 1.15 1.29
20 0.63 0.69 0.75 0.81 0.87 0.93 0.99 1.05 1.12 1.18 1.30 1.43 1.68 1.93 2.18 2.44
30 0.91 1.00 1.09 1.18 1.26 1.35 1.44 1.53 1.62 1.71 1.89 2.07 2.43 2.80 3.17 3.54
50 1.46 1.60 1.74 1.88 2.02 2.17 2.31 2.45 2.59 2.74 3.02 3.31 3.90 4.48 5.07 5.66
70 1.99 2.18 2.37 2.57 2.76 2.95 3.15 3.34 3.53 3.73 4.12 4.52 5.31 6.11 6.91 7.72
100 2.77 3.03 3.30 3.56 3.83 4.10 4.37 4.64 4.91 5.18 5.72 6.27 7.37 8.48 9.59 10.71
200 5.23 5.73 6.24 6.74 7.24 7.75 8.26 8.77 9.28 9.80 10.83 11.86 13.94 16.04 18.15 20.27
300 7.60 8.33 9.05 9.79 10.52 11.26 12.00 12.74 13.48 14.23 15.72 17.22 20.24 23.29 26.35 29.42
400 9.90 10.85 11.80 12.75 13.71 14.67 15.63 16.60 17.56 18.53 20.48 22.44 26.37 30.33 34.32 38.32
500 12.16 13.32 14.49 15.66 16.83 18.01 19.19 20.37 21.56 22.76 25.15 27.55 32.37 37.23 42.12 47.03
600 14.38 15.75 17.13 18.51 19.90 21.30 22.69 24.09 25.50 26.91 29.73 32.57 38.27 44.02 49.79 55.59
700 16.57 18.15 19.74 21.33 22.93 24.54 26.15 27.76 29.38 31.00 34.26 37.52 44.09 50.70 57.34 64.00
800 18.73 20.52 22.32 24.12 25.92 27.74 29.56 31.38 33.21 35.04 38.72 42.41 49.83 57.29 64.79 72.30
900 20.17 22.15 24.15 26.16 28.18 30.21 32.25 34.30 36.36 38.42 42.58 46.75 55.18 63.69 72.26 80.88
1000 21.88 24.03 26.20 28.38 30.57 32.77 34.98 37.20 39.44 41.68 46.18 50.70 59.83 69.04 78.31 87.63
1100 23.55 25.87 28.20 30.55 32.90 35.28 37.65 40.04 42.44 44.85 49.69 54.55 64.36 74.24 84.19 94.18
1200 25.19 27.67 30.16 32.67 35.19 37.72 40.26 42.82 45.38 47.95 53.12 58.32 68.78 79.32 89.92 100.56
1300 26.80 29.44 32.09 34.75 37.43 40.12 42.82 45.54 48.26 50.99 56.49 62.00 73.11 84.28 95.51 106.76
1400 28.38 31.17 33.97 36.79 39.63 42.48 45.33 48.20 51.09 53.97 59.78 65.61 77.34 89.13 100.96 112.80
1500 29.93 32.87 35.83 38.80 41.79 44.79 47.80 50.82 53.86 56.90 63.01 69.14 81.48 93.86 106.28 118.69
1600 31.46 34.55 37.65 40.78 43.91 47.07 50.23 53.40 56.58 59.77 66.18 72.61 85.53 98.50 111.47 124.42
1700 32.96 36.20 39.45 42.72 46.00 49.30 52.61 55.93 59.26 62.60 69.30 76.02 89.51 103.03 116.55 130.01
1800 34.45 37.83 41.22 44.64 48.06 51.51 54.96 58.42 61.90 65.38 72.37 79.37 93.41 107.47 121.50 135.45
1900 35.91 39.43 42.97 46.52 50.09 53.68 57.27 60.88 64.50 68.11 75.38 82.66 97.24 111.81 126.33 140.75
2000 37.35 41.02 44.69 48.39 52.09 55.82 59.55 63.29 67.05 70.81 78.34 85.89 100.99 116.06 131.05 145.90
2500 44.32 48.66 53.00 57.35 61.72 66.11 70.49 74.88 79.29 83.68 92.48 101.25 118.71 135.95 152.92 169.50
3000 50.93 55.88 60.84 65.81 70.78 75.77 80.75 85.72 90.70 95.66 105.55 115.36 134.73 153.62 171.90 189.42
3500 57.23 62.76 68.29 73.82 79.34 84.87 90.38 95.87 101.35 106.79 117.61 128.27 149.08 169.00
4000 63.25 69.31 75.37 81.41 87.43 93.45 99.42 105.35 111.26 117.11 128.67 139.97 161.70
4500 69.01 75.57 82.11 88.61 95.08 101.51 107.88 114.19 120.45 126.61 138.71 150.42
5000 74.53 81.55 88.51 95.43 102.28 109.07 115.77 122.37 128.89 135.28 147.71 159.58
NOTE: FOR SPROCKET SPEEDS ABOVE 5000 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 8mm Horsepower Tables
BELT HORSEPOWER RATINGS60mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
SmallestSprocketRpm
41
BELT HORSEPOWER RATINGS20mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
20 mm (0.787 in.) wide belt (PTH14M-20)
No. Teeth 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80
P.D. (mm) 124.78 129.23 133.69 142.60 151.52 160.43 169.34 178.25 196.08 213.90 231.73 249.55 267.38 285.21 303.03 320.86 356.51
P.D. (in) 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036
RPM HORSEPOWER RATING (Hp)
870 28.22 29.23 30.24 32.26 34.28 36.31 38.33 40.34 44.37 48.39 52.40 56.39 60.37 64.33 68.27 72.20 79.98
1160 34.93 36.17 37.42 39.91 42.39 44.88 47.35 49.82 54.74 59.63 64.49 69.31 74.10 78.84 83.54 88.19 97.34
1750 47.19 48.85 50.50 53.80 57.07 60.33 63.57 66.78 73.13 79.38 85.51 91.50 97.36 103.07 108.62 114.00 124.20
3450 74.97 77.34 79.67 84.22 88.62 92.86 96.92 100.79
10 0.46 0.47 0.49 0.52 0.56 0.59 0.62 0.65 0.72 0.78 0.85 0.92 0.98 1.05 1.11 1.18 1.31
20 0.87 0.90 0.93 0.99 1.05 1.11 1.18 1.24 1.36 1.48 1.61 1.73 1.86 1.98 2.10 2.23 2.48
30 1.26 1.30 1.35 1.44 1.53 1.62 1.71 1.80 1.98 2.16 2.34 2.52 2.70 2.88 3.06 3.24 3.59
50 2.01 2.08 2.15 2.30 2.44 2.59 2.73 2.87 3.16 3.45 3.74 4.02 4.31 4.60 4.89 5.18 5.75
70 2.74 2.84 2.94 3.13 3.33 3.52 3.72 3.92 4.31 4.70 5.09 5.48 5.88 6.27 6.66 7.05 7.84
100 3.81 3.94 4.08 4.35 4.62 4.89 5.17 5.44 5.98 6.53 7.07 7.61 8.16 8.70 9.25 9.79 10.88
200 7.20 7.46 7.71 8.23 8.74 9.26 9.77 10.29 11.32 12.34 13.37 14.40 15.43 16.46 17.49 18.52 20.57
300 10.45 10.83 11.20 11.95 12.69 13.44 14.19 14.93 16.43 17.92 19.41 20.90 22.40 23.89 25.38 26.87 29.84
400 13.62 14.10 14.59 15.56 16.53 17.51 18.48 19.45 21.39 23.34 25.28 27.22 29.16 31.09 33.03 34.96 38.83
500 16.72 17.31 17.91 19.10 20.29 21.49 22.68 23.87 26.25 28.63 31.01 33.38 35.76 38.13 40.49 42.86 47.57
600 19.76 20.47 21.17 22.58 23.99 25.40 26.80 28.21 31.02 33.83 36.63 39.43 42.23 45.02 47.80 50.58 56.12
700 22.76 23.57 24.39 26.01 27.63 29.25 30.87 32.48 35.72 38.94 42.16 45.37 48.58 51.77 54.96 58.14 64.47
800 25.73 26.64 27.56 29.39 31.22 33.05 34.87 36.70 40.34 43.97 47.60 51.21 54.81 58.40 61.98 65.54 72.63
900 28.94 29.97 31.01 33.08 35.16 37.23 39.30 41.36 45.49 49.60 53.71 57.79 61.86 65.92 69.95 73.96 81.91
1000 31.29 32.41 33.53 35.77 38.01 40.24 42.47 44.70 49.14 53.57 57.97 62.36 66.72 71.06 75.36 79.64 88.10
1100 33.58 34.78 35.98 38.38 40.77 43.16 45.55 47.93 52.67 57.39 62.09 66.75 71.39 75.99 80.54 85.06 93.97
1200 35.81 37.09 38.37 40.92 43.46 46.00 48.53 51.06 56.09 61.09 66.06 70.98 75.87 80.71 85.49 90.23 99.52
1300 37.99 39.34 40.69 43.39 46.08 48.76 51.44 54.10 59.41 64.67 69.89 75.06 80.17 85.22 90.21 95.13 104.75
1400 40.11 41.54 42.96 45.80 48.63 51.45 54.26 57.06 62.63 68.14 73.59 78.98 84.30 89.54 94.70 99.78 109.65
1500 42.19 43.68 45.18 48.15 51.12 54.07 57.01 59.94 65.75 71.49 77.16 82.74 88.25 93.66 98.97 104.17 114.23
1600 44.22 45.78 47.34 50.45 53.54 56.62 59.69 62.73 68.77 74.72 80.59 86.36 92.03 97.58 103.00 108.30 118.47
1700 46.21 47.84 49.46 52.69 55.91 59.11 62.29 65.45 71.70 77.85 83.90 89.83 95.63 101.29 106.81 112.17 122.38
1800 48.16 49.84 51.53 54.89 58.22 61.54 64.82 68.09 74.54 80.87 87.08 93.14 99.05 104.80 110.38 115.76
1900 50.06 51.81 53.56 57.03 60.47 63.90 67.29 70.65 77.29 83.78 90.13 96.30 102.30 108.11 113.71 119.09
2000 51.93 53.74 55.54 59.12 62.67 66.20 69.69 73.15 79.95 86.59 93.05 99.31 105.37 111.20 116.79
2500 60.71 62.77 64.82 68.88 72.88 76.82 80.69 84.49 91.88 98.94 105.65 111.98
3000 68.61 70.86 73.09 77.48 81.77 85.95 90.02 93.96 101.47
3500 75.64 78.01 80.35 84.91 89.31 93.55 97.59 101.45
NOTE: FOR SPROCKET SPEEDS ABOVE 3500 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 14mm Horsepower Tables
SmallestSprocketRpm
42
BELT HORSEPOWER RATINGS42mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
42 mm (1.654 in.) wide belt (PTH14M-42)
No. Teeth 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80
P.D. (mm) 124.78 129.23 133.69 142.60 151.52 160.43 169.34 178.25 196.08 213.90 231.73 249.55 267.38 285.21 303.03 320.86 356.51
P.D. (in) 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036
RPM HORSEPOWER RATING (Hp)
870 59.31 61.44 63.57 67.82 72.07 76.33 80.57 84.81 93.28 101.72 110.15 118.54 126.90 135.23 143.52 151.78 168.15
1160 73.43 76.04 78.67 83.90 89.12 94.34 99.54 104.73 115.07 125.35 135.57 145.71 155.77 165.75 175.62 185.40 204.63
1750 99.20 102.68 106.16 113.09 119.98 126.83 133.63 140.38 153.74 166.87 179.76 192.37 204.69 216.70 228.36 239.67 261.12
3450 157.62 162.59 167.50 177.07 186.32 195.23 203.76 211.91
10 0.96 1.00 1.03 1.10 1.17 1.24 1.31 1.37 1.51 1.65 1.79 1.92 2.06 2.20 2.34 2.48 2.75
20 1.82 1.88 1.95 2.08 2.21 2.34 2.47 2.60 2.86 3.12 3.38 3.64 3.90 4.16 4.42 4.68 5.20
30 2.64 2.74 2.83 3.02 3.21 3.40 3.59 3.78 4.15 4.53 4.91 5.29 5.67 6.04 6.42 6.80 7.56
50 4.23 4.38 4.53 4.83 5.13 5.44 5.74 6.04 6.65 7.25 7.86 8.46 9.07 9.67 10.28 10.88 12.09
70 5.76 5.97 6.17 6.59 7.00 7.41 7.82 8.23 9.06 9.88 10.71 11.53 12.35 13.18 14.00 14.83 16.48
100 8.00 8.28 8.57 9.14 9.71 10.29 10.86 11.43 12.57 13.72 14.86 16.01 17.15 18.30 19.44 20.59 22.87
200 15.13 15.67 16.22 17.30 18.38 19.46 20.54 21.62 23.79 25.95 28.12 30.28 32.44 34.61 36.77 38.93 43.25
300 21.97 22.76 23.54 25.11 26.68 28.25 29.82 31.39 34.53 37.67 40.81 43.94 47.08 50.22 53.35 56.48 62.74
400 28.63 29.65 30.67 32.71 34.76 36.80 38.85 40.89 44.97 49.06 53.14 57.21 61.29 65.36 69.43 73.50 81.62
500 35.14 36.39 37.65 40.16 42.66 45.17 47.68 50.18 55.19 60.19 65.19 70.18 75.17 80.15 85.13 90.10 100.01
600 41.54 43.02 44.51 47.47 50.43 53.39 56.35 59.31 65.22 71.12 77.01 82.89 88.77 94.63 100.49 106.33 117.97
700 47.86 49.56 51.27 54.67 58.08 61.49 64.89 68.29 75.08 81.86 88.63 95.38 102.12 108.84 115.54 122.22 135.52
800 54.09 56.01 57.94 61.79 65.63 69.48 73.31 77.15 84.80 92.44 100.06 107.65 115.23 122.78 130.30 137.79 152.68
900 60.83 63.01 65.19 69.55 73.91 78.26 82.61 86.96 95.63 104.28 112.90 121.49 130.05 138.57 147.04 155.48 172.19
1000 65.78 68.14 70.49 75.20 79.90 84.60 89.28 93.96 103.31 112.61 121.88 131.09 140.26 149.38 158.43 167.43 185.21
1100 70.60 73.12 75.64 80.68 85.71 90.74 95.75 100.75 110.73 120.65 130.53 140.33 150.07 159.74 169.32 178.83 197.55
1200 75.29 77.97 80.66 86.02 91.36 96.71 102.03 107.34 117.92 128.43 138.87 149.23 159.49 169.67 179.73 189.68 209.22
1300 79.86 82.70 85.54 91.21 96.87 102.51 108.13 113.74 124.90 135.96 146.93 157.79 168.54 179.16 189.65 199.99 220.21
1400 84.33 87.32 90.31 96.28 102.23 108.16 114.07 119.96 131.66 143.24 154.70 166.03 177.21 188.24 199.09 209.77 230.52
1500 88.70 91.83 94.97 101.23 107.46 113.67 119.85 126.00 138.21 150.28 162.20 173.95 185.52 196.90 208.06 219.00 240.15
1600 92.97 96.24 99.52 106.06 112.56 119.04 125.47 131.88 144.57 157.09 169.43 181.55 193.47 205.14 216.55 227.69 249.08
1700 97.15 100.56 103.98 110.77 117.53 124.27 130.95 137.59 150.73 163.67 176.38 188.84 201.04 212.95 224.55 235.82 257.29
1800 101.24 104.78 108.33 115.38 122.39 129.36 136.28 143.14 156.71 170.02 183.07 195.81 208.25 220.34 232.05 243.38
1900 105.25 108.92 112.59 119.89 127.13 134.33 141.46 148.54 162.49 176.14 189.48 202.46 215.08 227.29 239.06 250.37
2000 109.17 112.97 116.76 124.29 131.76 139.17 146.51 153.77 168.08 182.03 195.62 208.79 221.53 233.80 245.55
2500 127.64 131.96 136.28 144.80 153.21 161.50 169.64 177.63 193.17 208.02 222.13 235.43
3000 144.24 148.97 153.66 162.89 171.90 180.70 189.25 197.54 213.33
3500 159.02 164.00 168.93 178.52 187.77 196.68 205.19 213.29
NOTE: FOR SPROCKET SPEEDS ABOVE 3500 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 14mm Horsepower Tables
SmallestSprocketRpm
43
BELT HORSEPOWER RATINGS65mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
65 mm (2.559 in.) wide belt (PTH14M-65)
No. Teeth 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80
P.D. (mm) 124.78 129.23 133.69 142.60 151.52 160.43 169.34 178.25 196.08 213.90 231.73 249.55 267.38 285.21 303.03 320.86 356.51
P.D. (in) 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036
RPM HORSEPOWER RATING (Hp)
870 91.83 95.12 98.41 105.00 111.58 118.16 124.73 131.30 144.41 157.48 170.52 183.52 196.47 209.36 222.20 234.97 260.32
1160 113.67 117.73 121.79 129.89 137.97 146.05 154.10 162.14 178.15 194.07 209.88 225.58 241.16 256.60 271.89 287.03 316.80
1750 153.58 158.97 164.36 175.08 185.74 196.35 206.88 217.34 238.02 258.34 278.29 297.82 316.90 335.49 353.55 371.06 404.27
3450 244.02 251.72 259.31 274.13 288.45 302.25 315.47 328.09
10 1.49 1.54 1.60 1.70 1.81 1.91 2.02 2.13 2.34 2.55 2.77 2.98 3.19 3.41 3.62 3.83 4.26
20 2.82 2.92 3.02 3.22 3.42 3.62 3.82 4.03 4.43 4.83 5.23 5.64 6.04 6.44 6.85 7.25 8.06
30 4.09 4.24 4.38 4.68 4.97 5.26 5.55 5.85 6.43 7.02 7.60 8.19 8.77 9.36 9.94 10.53 11.70
50 6.54 6.78 7.01 7.48 7.95 8.42 8.88 9.35 10.29 11.23 12.16 13.10 14.03 14.97 15.91 16.85 18.72
70 8.92 9.24 9.56 10.19 10.83 11.47 12.11 12.75 14.02 15.30 16.57 17.85 19.13 20.40 21.68 22.96 25.51
100 12.38 12.83 13.27 14.15 15.04 15.93 16.81 17.70 19.47 21.24 23.01 24.78 26.55 28.33 30.10 31.87 35.41
200 23.43 24.27 25.10 26.78 28.45 30.13 31.80 33.48 36.83 40.18 43.53 46.87 50.22 53.57 56.92 60.27 66.96
300 34.02 35.23 36.45 38.88 41.31 43.74 46.17 48.60 53.46 58.32 63.18 68.03 72.89 77.74 82.59 87.44 97.13
400 44.32 45.90 47.48 50.65 53.81 56.98 60.14 63.30 69.63 75.95 82.26 88.58 94.89 101.19 107.49 113.79 126.36
500 54.40 56.34 58.28 62.17 66.05 69.93 73.81 77.69 85.44 93.18 100.92 108.65 116.37 124.09 131.79 139.48 154.83
600 64.32 66.61 68.90 73.49 78.07 82.66 87.24 91.81 100.96 110.10 119.22 128.33 137.43 146.51 155.57 164.61 182.63
700 74.09 76.72 79.37 84.64 89.92 95.19 100.46 105.72 116.24 126.73 137.21 147.66 158.09 168.50 178.87 189.22 209.81
800 83.74 86.71 89.70 95.65 101.60 107.56 113.50 119.43 131.29 143.11 154.91 166.66 178.39 190.08 201.72 213.32 236.37
900 94.17 97.55 100.93 107.67 114.42 121.16 127.90 134.62 148.05 161.44 174.79 188.09 201.34 214.53 227.64 240.70 266.57
1000 101.84 105.48 109.13 116.42 123.69 130.97 138.22 145.47 159.94 174.34 188.68 202.95 217.15 231.26 245.28 259.21 286.73
1100 109.30 113.20 117.11 124.91 132.69 140.48 148.24 155.98 171.43 186.79 202.07 217.25 232.34 247.30 262.14 276.85 305.84
1200 116.56 120.71 124.87 133.16 141.44 149.72 157.96 166.18 182.56 198.83 215.00 231.03 246.92 262.67 278.24 293.65 323.90
1300 123.64 128.03 132.43 141.21 149.96 158.70 167.41 176.09 193.36 210.48 227.47 244.28 260.93 277.37 293.61 309.62 340.92
1400 130.55 135.18 139.82 149.06 158.27 167.45 176.60 185.71 203.82 221.76 239.51 257.04 274.36 291.43 308.23 324.76 356.89
1500 137.31 142.17 147.03 156.71 166.36 175.98 185.55 195.07 213.97 232.66 251.11 269.30 287.22 304.83 322.11 339.05 371.80
1600 143.93 149.00 154.08 164.19 174.26 184.29 194.25 204.16 223.82 243.20 262.30 281.08 299.52 317.59 335.25 352.50 385.62
1700 150.40 155.68 160.97 171.49 181.96 192.38 202.73 213.01 233.36 253.38 273.07 292.36 311.25 329.69 347.64 365.09 398.33
1800 156.73 162.22 167.71 178.63 189.48 200.27 210.98 221.60 242.61 263.21 283.42 303.15 322.40 341.12 359.26 376.80
1900 162.94 168.62 174.31 185.60 196.82 207.97 219.01 229.96 251.56 272.69 293.35 313.45 332.98 351.88 370.11 387.62
2000 169.02 174.89 180.76 192.42 203.98 215.46 226.82 238.07 260.21 281.82 302.85 323.25 342.97 361.96 380.15
2500 197.60 204.30 210.98 224.18 237.19 250.02 262.63 275.01 299.06 322.05 343.90 364.50
3000 223.31 230.63 237.90 252.18 266.13 279.76 292.99 305.84 330.28
3500 246.18 253.91 261.53 276.38 290.71 304.49 317.67 330.22
NOTE: FOR SPROCKET SPEEDS ABOVE 3500 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 14mm Horsepower Tables
SmallestSprocketRpm
44
BELT HORSEPOWER RATINGS90mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
90 mm (3.543 in.) wide belt (PTH14M-90)
No. Teeth 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80
P.D. (mm) 124.78 129.23 133.69 142.60 151.52 160.43 169.34 178.25 196.08 213.90 231.73 249.55 267.38 285.21 303.03 320.86 356.51
P.D. (in) 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036
RPM HORSEPOWER RATING (Hp)
870 127.17 131.72 136.29 145.41 154.52 163.64 172.74 181.83 199.99 218.09 236.15 254.14 272.08 289.94 307.71 325.40 360.50
1160 157.42 163.03 168.66 179.87 191.07 202.26 213.41 224.54 246.71 268.75 290.66 312.39 333.97 355.36 376.53 397.50 438.72
1750 212.69 220.15 227.61 242.46 257.23 271.92 286.50 300.98 329.62 357.77 385.40 412.44 438.86 464.61 489.62 513.87 559.86
3450 337.94 348.59 359.12 379.64 399.47 418.58 436.89 454.36
10 2.06 2.14 2.21 2.36 2.50 2.65 2.80 2.95 3.24 3.54 3.83 4.13 4.42 4.72 5.01 5.31 5.90
20 3.90 4.04 4.18 4.46 4.74 5.02 5.30 5.57 6.13 6.69 7.25 7.81 8.37 8.92 9.48 10.04 11.16
30 5.67 5.87 6.07 6.48 6.88 7.29 7.69 8.10 8.91 9.72 10.53 11.34 12.15 12.96 13.77 14.58 16.20
50 9.06 9.39 9.71 10.36 11.01 11.66 12.30 12.95 14.25 15.55 16.84 18.14 19.44 20.73 22.03 23.33 25.92
70 12.35 12.79 13.24 14.12 15.00 15.89 16.77 17.65 19.42 21.19 22.95 24.72 26.49 28.26 30.02 31.79 35.33
100 17.15 17.76 18.38 19.60 20.83 22.05 23.28 24.51 26.96 29.41 31.87 34.32 36.77 39.23 41.68 44.13 49.04
200 32.45 33.60 34.76 37.08 39.40 41.72 44.04 46.36 51.00 55.64 60.28 64.91 69.55 74.19 78.83 83.46 92.73
300 47.11 48.79 50.47 53.84 57.21 60.57 63.94 67.30 74.04 80.76 87.49 94.21 100.94 107.66 114.37 121.09 134.51
400 61.37 63.56 65.75 70.14 74.52 78.90 83.28 87.66 96.42 105.17 113.92 122.66 131.40 140.14 148.86 157.58 174.99
500 75.34 78.02 80.71 86.09 91.46 96.84 102.21 107.58 118.32 129.04 139.76 150.46 161.16 171.84 182.51 193.16 214.42
600 89.07 92.24 95.42 101.77 108.12 114.47 120.81 127.15 139.82 152.47 165.11 177.72 190.32 202.89 215.44 227.96 252.92
700 102.60 106.25 109.91 117.22 124.52 131.83 139.12 146.41 160.97 175.50 190.02 204.49 218.93 233.34 247.71 262.04 290.55
800 115.96 120.08 124.22 132.47 140.71 148.95 157.18 165.40 181.82 198.19 214.52 230.81 247.05 263.23 279.35 295.42 327.34
900 130.42 135.09 139.77 149.11 158.45 167.80 177.12 186.43 205.03 223.57 242.06 260.47 278.82 297.09 315.25 333.33 369.17
1000 141.03 146.08 151.13 161.22 171.30 181.37 191.42 201.46 221.49 241.43 261.30 281.06 300.72 320.27 339.68 358.97 397.09
1100 151.36 156.76 162.17 172.98 183.76 194.54 205.29 216.01 237.41 258.68 279.84 300.87 321.75 342.48 363.03 383.40 423.54
1200 161.41 167.16 172.92 184.41 195.88 207.34 218.75 230.14 252.82 275.36 297.74 319.94 341.95 363.76 385.33 406.67 448.56
1300 171.22 177.31 183.40 195.55 207.68 219.78 231.84 243.85 267.77 291.49 315.01 338.30 361.35 384.12 406.60 428.78 472.13
1400 180.80 187.21 193.63 206.42 219.17 231.90 244.57 257.18 282.27 307.10 331.68 355.96 379.95 403.59 426.85 449.74 494.25
1500 190.16 196.88 203.61 217.02 230.38 243.71 256.95 270.14 296.32 322.20 347.76 372.95 397.76 422.15 446.08 469.54 514.89
1600 199.32 206.34 213.38 227.38 241.32 255.21 269.01 282.74 309.96 336.80 363.25 389.25 414.79 439.82 464.28 488.17 534.04
1700 208.28 215.60 222.92 237.49 251.99 266.42 280.75 294.99 323.17 350.90 378.16 404.88 431.03 456.57 481.43 505.61 551.64
1800 217.05 224.65 232.26 247.37 262.40 277.35 292.18 306.89 335.97 364.52 392.49 419.82 446.48 472.41 497.53 521.83
1900 225.64 233.52 241.39 257.03 272.57 288.00 303.30 318.46 348.37 377.64 406.24 434.09 461.13 487.31 512.55 536.81
2000 234.06 242.20 250.32 266.47 282.48 298.38 314.11 329.69 360.36 390.28 419.41 447.66 474.97 501.27 526.47
2500 273.65 282.93 292.17 310.45 328.48 346.25 363.70 380.85 414.16 446.00 476.26 504.79
3000 309.25 319.39 329.45 349.23 368.56 387.42 405.76 423.54 457.39
3500 340.93 351.63 362.18 382.75 402.59 421.69 439.94 457.32
NOTE: FOR SPROCKET SPEEDS ABOVE 3500 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 14mm Horsepower Tables
SmallestSprocketRpm
45
BELT HORSEPOWER RATINGS120mm WIDE BELTSThe following tables represent the horsepower ratings for each belt at the pre-determined No. of Teeth, Pitch Diameter and RPM. These ratings must be multiplied by the applicable belt length factor to obtain corrected HP rating.
120 mm (4.724 in.) wide belt (PTH14M-120)
No. Teeth 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80
P.D. (mm) 124.78 129.23 133.69 142.60 151.52 160.43 169.34 178.25 196.08 213.90 231.73 249.55 267.38 285.21 303.03 320.86 356.51
P.D. (in) 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036
RPM HORSEPOWER RATING (Hp)
870 169.58 175.65 181.74 193.90 206.05 218.21 230.34 242.46 266.68 290.82 314.90 338.89 362.81 386.63 410.32 433.92 480.72
1160 209.92 217.40 224.90 239.86 254.79 269.71 284.58 299.42 328.99 358.38 387.59 416.57 445.34 473.87 502.10 530.06 585.03
1750 283.61 293.57 303.52 323.32 343.01 362.60 382.05 401.35 439.55 477.08 513.93 549.98 585.21 619.55 652.90 685.24 746.57
3450 450.64 464.85 478.88 506.25 532.69 558.18 582.59 605.89
10 2.75 2.85 2.95 3.14 3.34 3.54 3.73 3.93 4.32 4.72 5.11 5.50 5.90 6.29 6.68 7.08 7.86
20 5.20 5.39 5.57 5.95 6.32 6.69 7.06 7.43 8.18 8.92 9.67 10.41 11.16 11.90 12.64 13.39 14.88
30 7.55 7.82 8.09 8.63 9.17 9.72 10.26 10.80 11.88 12.96 14.04 15.12 16.20 17.28 18.36 19.44 21.61
50 12.09 12.52 12.95 13.81 14.68 15.54 16.41 17.27 19.00 20.73 22.46 24.19 25.92 27.65 29.38 31.11 34.57
70 16.47 17.06 17.65 18.83 20.00 21.18 22.36 23.54 25.89 28.25 30.61 32.96 35.32 37.68 40.03 42.39 47.11
100 22.87 23.68 24.50 26.14 27.77 29.41 31.04 32.68 35.95 39.22 42.49 45.76 49.04 52.31 55.58 58.85 65.39
200 43.27 44.81 46.36 49.45 52.54 55.64 58.73 61.82 68.01 74.19 80.38 86.56 92.75 98.93 105.11 111.30 123.66
300 62.82 65.06 67.31 71.80 76.28 80.78 85.26 89.75 98.73 107.69 116.67 125.63 134.60 143.56 152.52 161.47 179.37
400 81.84 84.76 87.68 93.53 99.37 105.22 111.06 116.90 128.58 140.25 151.92 163.57 175.23 186.87 198.50 210.13 233.34
500 100.46 104.04 107.63 114.80 121.97 129.14 136.30 143.46 157.78 172.08 186.37 200.64 214.91 229.15 243.37 257.58 285.92
600 118.77 123.00 127.24 135.71 144.17 152.64 161.10 169.55 186.45 203.31 220.17 236.98 253.78 270.55 287.28 303.98 337.27
700 136.82 141.69 146.57 156.31 166.05 175.79 185.52 195.23 214.66 234.03 253.38 272.68 291.94 311.16 330.31 349.42 387.45
800 154.63 160.13 165.64 176.64 187.63 198.62 209.59 220.55 242.45 264.28 286.06 307.78 329.43 351.01 372.51 393.93 436.50
900 173.91 180.14 186.38 198.84 211.29 223.75 236.18 248.60 273.41 298.13 322.79 347.34 371.80 396.16 420.39 444.50 492.28
1000 188.07 194.79 201.53 214.98 228.42 241.85 255.26 268.64 295.35 321.94 348.44 374.78 401.01 427.07 452.96 478.68 529.51
1100 201.83 209.04 216.26 230.66 245.04 259.42 273.75 288.05 316.58 344.94 373.17 401.20 429.05 456.69 484.09 511.26 564.79
1200 215.24 222.91 230.59 245.91 261.20 276.48 291.70 306.88 337.14 367.18 397.03 426.63 455.99 485.07 513.83 542.29 598.15
1300 228.32 236.44 244.56 260.77 276.94 293.08 309.15 325.17 357.07 388.70 420.07 451.12 481.85 512.23 542.20 571.78 629.58
1400 241.09 249.64 258.20 275.26 292.27 309.24 326.12 342.95 376.40 409.51 442.29 474.67 506.65 538.18 569.20 599.73 659.07
1500 253.57 262.54 271.52 289.40 307.21 324.98 342.64 360.23 395.14 429.65 463.73 497.32 530.41 562.94 594.84 626.13 686.60
1600 265.78 275.16 284.53 303.21 321.80 340.32 358.72 377.03 413.32 449.11 484.39 519.06 553.12 586.49 619.11 650.97 712.13
1700 277.73 287.50 297.26 316.69 336.02 355.27 374.38 393.36 430.94 467.92 504.27 539.90 574.78 608.83 641.99 674.22 735.62
1800 289.43 299.57 309.71 329.87 349.91 369.84 389.61 409.24 448.02 486.08 523.39 559.83 595.38 629.95 663.45 695.85
1900 300.89 311.39 321.89 342.75 363.46 384.05 404.44 424.66 464.55 503.58 541.72 578.85 614.92 649.83 683.48 715.83
2000 312.12 322.97 333.80 355.33 376.69 397.89 418.86 439.64 480.53 520.43 559.28 596.95 633.37 668.44 702.04
2500 364.91 377.28 389.61 413.99 438.02 461.72 485.00 507.86 552.28 594.73 635.10 673.13
3000 412.38 425.90 439.32 465.70 491.47 516.63 541.07 564.79 609.93
3500 454.63 468.89 482.96 510.39 536.86 562.32 586.65 609.84
NOTE: FOR SPROCKET SPEEDS ABOVE 3500 RPM OR EMPTY CELLS INDICATING SPROCKET RIM SPEEDS GREATER THAN 6500 FEET PER MINUTE, CONSULT CARLISLE.
THE SHADED AREA INDICATES A REDUCTION IN BELT SERVICE LIFE.
RPP PANTHER ULTRA-CORD Belt 14mm Horsepower Tables
SmallestSprocketRpm
46
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
BELT LENGTH CODE (MM)480 560 600 640 720 800 880 960 1040
NUMBER OF BELT TEETH60 70 75 80 90 100 110 120 130
BELT LENGTH CORRECTION FACTOR (KL)0.8 0.8 0.8 0.9 0.9 0.9 0.9 1 1
1.00 80 203.72 8.020 80 203.72 8.020 1750 26.5 48.6 77.4 132.7
1.00 72 183.35 7.218 72 183.35 7.218 1750 23.8 43.6 69.4 119.0 7.56 9.13
1.00 64 162.97 6.416 64 162.97 6.416 1750 21.0 38.6 61.4 105.3 7.24 8.82 10.39
1.00 56 142.60 5.614 56 142.60 5.614 1750 18.3 33.5 53.3 91.5 6.93 8.50 10.08 11.65
1.00 48 122.23 4.812 48 122.23 4.812 1750 15.5 28.5 45.3 77.7 5.04 6.61 8.19 9.76 11.34 12.91
1.00 44 112.05 4.411 44 112.05 4.411 1750 14.1 26.0 41.3 70.8 4.88 5.67 7.24 8.82 10.39 11.97 13.54
1.00 40 101.86 4.010 40 101.86 4.010 1750 12.8 23.5 37.3 64.0 4.72 5.51 6.30 7.87 9.45 11.02 12.60 14.17
1.00 38 96.77 3.810 38 96.77 3.810 1750 12.1 22.2 35.3 60.6 5.04 5.83 6.61 8.19 9.76 11.34 12.91 14.49
1.00 36 91.67 3.609 36 91.67 3.609 1750 11.4 21.0 33.3 57.2 3.78 5.35 6.14 6.93 8.50 10.08 11.65 13.23 14.80
1.00 34 86.58 3.409 34 86.58 3.409 1750 10.7 19.7 31.4 53.8 4.09 5.67 6.46 7.24 8.82 10.39 11.97 13.54 15.12
1.00 32 81.49 3.208 32 81.49 3.208 1750 10.1 18.5 29.4 50.4 4.41 5.98 6.77 7.56 9.13 10.71 12.28 13.86 15.43
1.00 30 76.39 3.008 30 76.39 3.008 1750 9.4 17.2 27.4 47.0 4.72 6.30 7.09 7.87 9.45 11.02 12.60 14.17 15.75
1.00 28 71.30 2.807 28 71.30 2.807 1750 8.7 16.0 25.5 43.7 5.04 6.61 7.40 8.19 9.76 11.34 12.91 14.49 16.06
1.00 26 66.21 2.607 26 66.21 2.607 1750 8.1 14.8 23.5 40.3 5.35 6.93 7.71 8.50 10.08 11.65 13.23 14.80 16.38
1.00 24 61.12 2.406 24 61.12 2.406 1750 7.4 13.6 21.6 37.0 5.67 7.24 8.03 8.82 10.39 11.97 13.54 15.12 16.69
1.00 22 56.02 2.206 22 56.02 2.206 1750 6.7 12.4 19.7 33.7 5.98 7.56 8.34 9.13 10.71 12.28 13.86 15.43 17.01
1.05 38 96.77 3.810 40 101.86 4.010 1663 12.1 22.2 35.3 60.6 4.88 5.67 6.45 8.03 9.60 11.18 12.75 14.33
1.06 36 91.67 3.609 38 96.77 3.810 1658 11.4 21.0 33.3 57.2 5.19 5.98 6.77 8.34 9.92 11.49 13.07 14.64
1.06 34 86.58 3.409 36 91.67 3.609 1653 10.7 19.7 31.4 53.8 3.93 5.51 6.30 7.08 8.66 10.23 11.81 13.38 14.96
1.06 32 81.49 3.208 34 86.58 3.409 16.47 10.1 18.5 29.4 50.4 4.25 5.82 6.61 7.40 8.97 10.55 12.12 13.70 15.27
1.07 30 76.39 3.008 32 81.49 3.208 1641 9.4 17.2 27.4 47.0 4.56 6.14 6.93 7.71 9.29 10.86 12.44 14.01 15.59
1.07 28 71.30 2.807 30 76.39 3.008 1633 8.7 16.0 25.5 43.7 4.88 6.45 7.24 8.03 9.60 11.18 12.75 14.33 15.90
1.08 26 66.21 2.607 28 71.30 2.807 1625 8.1 14.8 23.5 40.3 5.19 6.77 7.56 8.34 9.92 11.49 13.07 14.64 16.22
1.08 24 61.12 2.406 26 66.21 2.607 1615 7.4 13.6 21.6 37.0 5.51 7.08 7.87 8.66 10.23 11.81 13.38 14.96 16.53
1.09 44 112.05 4.411 48 122.23 4.812 1604 14.1 26.0 41.3 70.8 5.35 6.93 8.50 10.08 11.65 13.23
1.09 22 56.02 2.206 24 61.12 2.406 1604 6.7 12.4 19.7 33.7 5.82 7.40 8.19 8.97 10.55 12.12 13.70 15.27 16.85
1.10 ...40 101.86 4.010 44 112.05 4.411 1591 12.8 23.5 37.3 64.0 4.40 5.19 5.98 7.56 9.13 10.71 12.28 13.86
1.11 72 183.35 7.218 80 203.72 8.020 1575 23.8 43.6 69.4 119.0 8.49
1.11 36 91.67 3.609 40 101.86 4.010 1575 11.4 21.0 33.3 57.2 5.03 5.82 6.61 8.19 9.76 11.34 12.91 14.49
1.12 34 86.58 3.409 38 96.77 3.810 1566 10.7 19.7 31.4 53.8 3.77 5.35 6.14 6.92 8.50 10.08 11.65 13.23 14.80
1.13 80 203.72 8.020 90 229.18 9.023 1556 26.5 48.6 77.4 132.7
1.13 64 162.97 6.416 72 183.35 7.218 1556 21.0 38.6 61.4 105.3 8.18 9.76
1.13 32 81.49 3.208 36 91.67 3.609 1556 10.1 18.5 29.4 50.4 4.09 5.67 6.45 7.24 8.82 10.39 11.97 13.54 15.12
1.13 30 76.39 3.008 34 86.58 3.409 1544 9.4 17.2 27.4 47.0 4.40 5.98 6.77 7.55 9.13 10.71 12.28 13.86 15.43
1.14 56 142.60 5.614 64 162.97 6.416 1531 18.3 33.5 53.3 91.5 6.29 7.86 9.44 11.02
1.14 28 71.30 2.807 32 81.49 3.208 1531 8.7 16.0 25.5 43.7 4.72 6.30 7.08 7.87 9.45 11.02 12.60 14.17 15.75
1.15 26 66.21 2.607 30 76.39 3.008 1517 8.1 14.8 23.5 40.3 5.03 6.61 7.40 8.18 9.76 11.34 12.91 14.49 16.06
1.16 38 96.77 3.810 44 112.05 4.411 1511 12.1 22.2 35.3 60.6 4.56 5.34 6.13 7.71 9.29 10.86 12.44 14.01
1.17 48 122.23 4.812 56 142.60 5.614 1500 15.5 28.5 45.3 77.7 5.97 7.55 9.12 10.70 12.28
1.17 24 61.12 2.406 28 71.30 2.807 1500 7.4 13.6 21.6 37.0 5.35 6.93 7.71 8.50 10.08 11.65 13.23 14.80 16.38
1.18 34 86.58 3.409 40 101.86 4.010 1488 10.7 19.7 31.4 53.8 5.19 5.98 6.76 8.34 9.92 11.49 13.07 14.64
1.18 22 56.02 2.206 26 66.21 2.607 1481 6.7 12.4 19.7 33.7 5.66 7.24 8.03 8.82 10.39 11.97 13.54 15.12 16.69
1.19 32 81.49 3.208 38 96.77 3.810 1474 10.1 18.5 29.4 50.4 3.92 5.50 6.29 7.08 8.66 10.23 11.81 13.38 14.96
1.20 40 101.86 4.010 48 122.23 4.812 1458 12.8 23.5 37.3 64.0 4.86 5.65 7.23 8.81 10.39 11.96 13.54
1.20 30 76.39 3.008 36 91.67 3.609 1458 9.4 17.2 27.4 47.0 4.24 5.82 6.61 7.39 8.97 10.55 12.12 13.70 15.27
1.21 28 71.30 2.807 34 86.58 3.409 1441 8.7 16.0 25.5 43.7 4.56 6.13 6.92 7.71 9.29 10.86 12.44 14.01 15.59
1.22 36 91.67 3.609 44 112.05 4.411 1432 11.4 21.0 33.3 57.2 4.71 5.50 6.29 7.86 9.44 11.02 12.59 14.17
1.23 26 66.21 2.607 32 81.49 3.208 1422 8.1 14.8 23.5 40.3 4.87 6.45 7.24 8.02 9.60 11.18 12.75 14.33 15.90
1.25 72 183.35 7.218 90 229.18 9.023 1400 23.8 43.6 69.4 119.0
1.25 64 162.97 6.416 80 203.72 8.020 1400 21.0 38.6 61.4 105.3 7.52 9.10
COMBINATIONS DRIVEN SPEEDS & HP RATINGS DRIVER DRIVEN 1750 RPM DRIVER
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 12 22 35 60
47
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
9.45 11.02 11.50 12.60 15.75 18.90 22.05 22.83 26.77 30.71 34.65 38.58 42.52 47.40 51.97 58.27 74.02
10.71 12.28 12.76 13.86 17.01 20.16 23.31 24.09 28.03 31.97 35.91 39.84 43.78 48.66 53.23 59.53 75.28
11.97 13.54 14.02 15.12 18.27 21.42 24.57 25.35 29.29 33.23 37.16 41.10 45.04 49.92 54.49 60.79 76.53
13.23 14.80 15.28 16.38 19.53 22.68 25.83 26.61 30.55 34.49 38.42 42.36 46.30 51.18 55.75 62.05 77.79
14.49 16.06 16.53 17.64 20.79 23.94 27.09 27.87 31.81 35.75 39.68 43.62 47.56 52.44 57.01 63.31 79.05
15.12 16.69 17.16 18.27 21.42 24.57 27.72 28.50 32.44 36.38 40.31 44.25 48.19 53.07 57.64 63.94 79.68
15.75 17.32 17.79 18.90 22.05 25.20 28.35 29.13 33.07 37.01 40.94 44.88 48.82 53.70 58.27 64.57 80.31
16.06 17.64 18.11 19.21 22.36 25.51 28.66 29.45 33.38 37.32 41.26 45.20 49.13 54.01 58.58 64.88 80.63
16.38 17.95 18.42 19.53 22.68 25.83 28.98 29.76 33.70 37.64 41.57 45.51 49.45 54.33 58.90 65.20 80.94
16.69 18.27 18.74 19.84 22.99 26.14 29.29 30.08 34.01 37.95 41.89 45.83 49.76 54.64 59.21 65.51 81.26
17.01 18.58 19.05 20.16 23.31 26.46 29.61 30.39 34.33 38.27 42.20 46.14 50.08 54.96 59.53 65.83 81.57
17.32 18.90 19.37 20.47 23.62 26.77 29.92 30.71 34.64 38.58 42.52 46.46 50.39 55.27 59.84 66.14 81.89
17.64 19.21 19.68 20.79 23.94 27.09 30.24 31.02 34.96 38.90 42.83 46.77 50.71 55.59 60.16 66.46 82.20
17.95 19.53 20.00 21.10 24.25 27.40 30.55 31.34 35.27 39.21 43.15 47.09 51.02 55.90 60.47 66.77 82.52
18.27 19.84 20.31 21.42 24.57 27.72 30.87 31.65 35.59 39.53 43.46 47.40 51.34 56.22 60.79 67.09 82.83
18.58 20.16 20.63 21.73 24.88 28.03 31.18 31.97 35.90 39.84 43.78 47.71 51.65 56.53 61.10 67.40 83.15
15.90 17.48 17.95 19.05 22.20 25.35 28.50 29.29 33.23 37.16 41.10 45.04 48.98 53.86 58.42 64.72 80.47
16.22 17.79 18.27 19.37 22.52 25.67 28.82 29.61 33.54 37.48 41.42 45.35 49.29 54.17 58.74 65.04 80.79
16.53 18.11 18.58 19.68 22.83 25.98 29.13 29.92 33.86 37.79 41.73 45.67 49.61 54.49 59.05 65.35 81.10
16.85 18.42 18.90 20.00 23.15 26.30 29.45 30.23 34.17 38.11 42.05 45.98 49.92 54.80 59.37 65.67 81.42
17.16 18.74 19.21 20.31 23.46 26.61 29.76 30.55 34.49 38.42 42.36 46.30 50.23 55.12 59.68 65.98 81.73
17.48 19.05 19.53 20.63 23.78 26.93 30.08 30.86 34.80 38.74 42.68 46.61 50.55 55.43 60.00 66.30 82.05
17.79 19.37 19.84 20.94 24.09 27.24 30.39 31.18 35.12 39.05 42.99 46.93 50.86 55.75 60.31 66.61 82.36
18.11 19.68 20.16 21.26 24.41 27.56 30.71 31.49 35.43 39.37 43.31 47.24 51.18 56.06 60.63 66.93 82.68
14.80 16.38 16.85 17.95 21.10 24.25 27.40 28.19 32.12 36.06 40.00 43.94 47.87 52.75 57.32 63.62 79.37
18.42 20.00 20.47 21.57 24.72 27.87 31.02 31.81 35.75 39.68 43.62 47.56 51.49 56.38 60.94 67.24 82.99
15.43 17.01 17.48 18.58 21.73 24.88 28.03 28.82 32.75 36.69 40.63 44.57 48.50 53.38 57.95 64.25 80.00
10.07 11.65 12.12 13.22 16.37 19.52 22.67 23.46 27.40 31.34 35.27 39.21 43.15 48.03 52.60 58.90 74.64
16.06 17.64 18.11 19.21 22.36 25.51 28.66 29.45 33.38 37.32 41.26 45.20 49.13 54.01 58.58 64.88 80.63
16.38 17.95 18.42 19.53 22.67 25.82 28.97 29.76 33.70 37.64 41.57 45.51 49.45 54.33 58.90 65.20 80.94
8.65 10.22 10.70 11.80 14.95 18.10 21.25 22.04 25.98 29.92 33.85 37.79 41.73 46.61 51.18 57.48 73.23
11.33 12.91 13.38 14.48 17.63 20.78 23.93 24.72 28.66 32.60 36.53 40.47 44.41 49.29 53.86 60.16 75.90
16.69 18.27 18.74 19.84 22.99 26.14 29.29 30.08 34.01 37.95 41.89 45.83 49.76 54.64 59.21 65.51 81.26
17.01 18.58 19.05 20.15 23.30 26.45 29.60 30.39 34.33 38.27 42.20 46.14 50.08 54.96 59.53 65.82 81.57
12.59 14.17 14.64 15.74 18.89 22.04 25.19 25.98 29.92 33.86 37.79 41.73 45.67 50.55 55.12 61.42 77.16
17.32 18.90 19.37 20.47 23.62 26.77 29.92 30.71 34.64 38.58 42.52 46.46 50.39 55.27 59.84 66.14 81.89
17.64 19.21 19.68 20.78 23.93 27.08 30.23 31.02 34.96 38.90 42.83 46.77 50.71 55.59 60.16 66.45 82.20
15.59 17.16 17.63 18.74 21.89 25.04 28.19 28.97 32.91 36.85 40.79 44.72 48.66 53.54 58.11 64.41 80.16
13.85 15.43 15.90 17.00 20.15 23.30 26.45 27.24 31.18 35.12 39.05 42.99 46.93 51.81 56.38 62.68 78.42
17.95 19.53 20.00 21.10 24.25 27.40 30.55 31.34 35.27 39.21 43.15 47.09 51.02 55.90 60.47 66.77 82.52
16.22 17.79 18.26 19.37 22.52 25.67 28.82 29.60 33.54 37.48 41.42 45.35 49.29 54.17 58.74 65.04 80.79
18.27 19.84 20.31 21.41 24.56 27.71 30.86 31.65 35.59 39.53 43.46 47.40 51.34 56.22 60.79 67.08 82.83
16.53 18.11 18.58 19.68 22.83 25.98 29.13 29.92 33.86 37.79 41.73 45.67 49.60 54.49 59.05 65.35 81.10
15.11 16.69 17.16 18.26 21.41 24.56 27.71 28.50 32.44 36.38 40.31 44.25 48.19 53.07 57.64 63.94 79.68
16.85 18.42 18.89 20.00 23.15 26.30 29.45 30.23 34.17 38.11 42.05 45.98 49.92 54.80 59.37 65.67 81.42
17.16 18.74 19.21 20.31 23.46 26.61 29.76 30.55 34.49 38.42 42.36 46.30 50.23 55.12 59.68 65.98 81.73
15.74 17.32 17.79 18.89 22.04 25.19 28.34 29.13 33.07 37.01 40.94 44.88 48.82 53.70 58.27 64.57 80.31
17.48 19.05 19.52 20.63 23.78 26.93 30.08 30.86 34.80 38.74 42.67 46.61 50.55 55.43 60.00 66.30 82.05
9.25 10.83 11.30 12.41 15.56 18.72 21.87 22.66 26.60 30.54 34.48 38.41 42.35 47.23 51.80 58.10 73.85
10.68 12.26 12.73 13.83 16.99 20.14 23.29 24.08 28.02 31.96 35.90 39.83 43.77 48.65 53.22 59.52 75.27
48
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
COMBINATIONS DRIVEN SPEEDS & HP RATINGS DRIVER DRIVEN 1750 RPM DRIVER
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 12 22 35 60
BELT LENGTH CODE (MM)480 560 600 640 720 800 880 960 1040
NUMBER OF BELT TEETH60 70 75 80 90 100 110 120 130
BELT LENGTH CORRECTION FACTOR (KL)0.8 0.8 0.8 0.9 0.9 0.9 0.9 1 1
1.25 32 81.49 3.208 40 101.86 4.010 1400 10.1 18.5 29.4 50.4 3.76 5.34 6.13 6.92 8.49 10.07 11.65 13.22 14.80
1.25 24 61.12 2.406 30 76.39 3.008 1400 7.4 13.6 21.6 37.0 5.19 6.76 7.55 8.34 9.92 11.49 13.07 14.64 16.22
1.26 38 96.77 3.810 48 122.23 4.812 1385 12.1 22.2 35.3 60.6 5.01 5.80 7.38 8.96 10.54 12.11 13.69
1.27 44 112.05 4.411 56 142.60 5.614 1375 14.1 26.0 41.3 70.8 6.27 7.85 9.43 11.01 12.58
1.27 30 76.39 3.008 38 96.77 3.810 1382 9.4 17.2 27.4 47.0 4.07 5.65 6.44 7.23 8.81 10.38 11.96 13.54 15.11
1.27 22 56.02 2.206 28 71.30 2.807 1375 6.7 12.4 19.7 33.7 5.50 7.08 7.87 8.66 10.23 11.81 13.38 14.96 16.53
1.29 56 142.60 5.614 72 183.35 7.218 1361 18.3 33.5 53.3 91.5 7.20 8.78 10.36
1.29 34 86.58 3.409 44 112.05 4.411 1352 10.7 19.7 31.4 53.8 4.85 5.65 6.44 8.01 9.59 11.17 12.74 14.32
1.29 28 71.30 2.807 36 91.67 3.609 1361 8.7 16.0 25.5 43.7 4.39 5.97 6.76 7.55 9.12 10.70 12.28 13.85 15.43
1.31 26 66.21 2.607 34 86.58 3.409 1338 8.1 14.8 23.5 40.3 4.71 6.28 7.07 7.86 9.44 11.01 12.59 14.17 15.74
1.33 48 122.23 4.812 64 162.97 6.416 1313 15.5 28.5 45.3 77.7 6.88 8.47 10.05 11.63
1.33 36 91.67 3.609 48 122.23 4.812 1313 11.4 21.0 33.3 57.2 4.37 5.16 5.95 7.53 9.11 10.69 12.27 13.84
1.33 30 76.39 3.008 40 101.86 4.010 1313 9.4 17.2 27.4 47.0 3.90 5.49 6.28 7.07 8.65 10.22 11.80 13.38 14.95
1.33 24 61.12 2.406 34 81.49 3.208 1313 7.4 13.6 21.6 37.0 5.02 6.60 7.39 8.18 9.75 11.33 12.91 14.48 16.06
1.36 28 71.30 2.807 38 96.77 3.810 1289 8.7 16.0 25.5 43.7 4.22 5.80 6.59 7.38 8.96 10.54 12.11 13.69 15.27
1.36 22 56.02 2.206 30 76.39 3.008 1283 6.7 12.4 19.7 33.7 5.34 6.92 7.70 8.49 10.07 11.65 13.22 14.80 16.37
1.38 32 81.49 3.208 44 112.05 4.411 1273 10.1 18.5 29.4 50.4 5.00 5.79 6.59 8.17 9.74 11.32 12.90 14.48
1.38 26 66.21 2.607 36 91.67 3.609 12.64 8.1 14.8 23.5 40.3 4.54 6.12 6.91 7.70 9.28 10.85 12.43 14.01 15.58
1.40 80 203.72 8.020 112 285.21 11.229 1250 26.5 48.6 77.4 132.7
1.40 40 101.86 4.010 56 142.60 5.614 1250 12.8 23.5 37.3 64.0 4.97 6.56 8.15 9.73 11.31 12.89
1.41 64 162.97 6.416 90 229.18 9.023 1244 21.0 38.6 61.4 105.3 8.24
1.41 34 86.58 3.409 48 122.23 4.812 1240 10.7 19.7 31.4 53.8 4.51 5.31 6.10 7.68 9.26 10.84 12.42 14.00
1.42 24 61.12 2.406 34 86.58 3.409 1235 7.4 13.6 21.6 37.0 4.85 6.44 7.23 8.01 9.59 11.17 12.74 14.32 15.90
1.43 56 142.60 5.614 80 203.72 8.020 1225 18.3 33.5 53.3 91.5 8.10 9.69
1.43 28 71.30 2.807 40 101.86 4.010 1225 8.7 16.0 25.5 43.7 4.05 5.64 6.43 7.22 8.80 10.38 11.95 13.53 15.11
1.45 44 112.05 4.411 64 162.97 6.416 1203 14.1 26.0 41.3 70.8 5.58 7.17 8.76 10.34 11.93
1.45 22 56.02 2.206 32 81.49 3.208 1203 6.7 12.4 19.7 33.7 5.17 6.75 7.54 8.33 9.91 11.48 13.06 14.64 16.21
1.46 26 66.21 2.607 38 96.77 3.810 1197 8.1 14.8 23.5 40.3 4.37 5.95 6.74 7.53 9.11 10.69 12.27 13.84 15.42
1.47 38 96.77 3.810 56 142.60 5.614 1188 12.1 22.2 35.3 60.6 5.12 6.71 8.30 9.88 11.46 13.04
1.47 30 76.39 3.008 44 112.05 4.411 1193 9.4 17.2 27.4 47.0 5.15 5.94 6.73 8.32 9.90 11.47 13.05 14.63
1.50 48 122.23 4.812 72 183.35 7.218 1167 15.5 28.5 45.3 77.7 6.18 7.78 9.37 10.96
1.50 32 81.49 3.208 48 122.23 4.812 1167 10.1 18.5 29.4 50.4 4.65 5.45 6.25 7.83 9.41 10.99 12.57 14.15
1.50 24 61.12 2.406 36 91.67 3.609 1167 7.4 13.6 21.6 37.0 4.69 6.27 7.06 7.85 9.43 11.01 12.58 14.16 15.74
1.54 26 66.21 2.607 40 101.86 4.010 1138 8.1 14.8 23.5 40.3 4.19 5.78 6.58 7.37 8.95 10.53 12.10 13.68 15.26
1.55 22 56.02 2.206 34 86.58 3.409 11.32 6.7 12.4 19.7 33.7 5.00 6.59 7.38 8.17 9.74 11.32 12.90 14.47 16.05
1.56 72 183.35 7.218 112 285.21 11.229 1125 23.8 43.6 69.4 119.0
1.56 36 91.67 3.609 56 142.60 5.614 1125 11.4 21.0 33.3 57.2 5.26 6.86 8.44 10.03 11.61 13.19
1.57 28 71.30 2.807 44 112.05 4.411 1114 8.7 16.0 25.5 43.7 3.69 5.29 6.09 6.88 8.47 10.05 11.63 13.20 14.78
1.58 24 61.12 2.406 38 96.77 3.810 1105 7.4 13.6 21.6 37.0 4.51 6.10 6.89 7.68 9.26 10.84 12.42 14.00 15.57
1.60 40 101.86 4.010 64 162.97 6.416 1094 12.8 23.5 37.3 64.0 5.86 7.46 9.05 10.64 12.22
1.60 30 76.39 3.008 48 122.23 4.812 1094 9.4 17.2 27.4 47.0 4.80 5.60 6.39 7.98 9.56 11.14 12.72 14.30
1.61 56 142.60 5.614 90 229.18 9.023 1089 18.3 33.5 53.3 91.5 8.81
1.64 44 112.05 4.411 72 183.35 7.218 1069 14.1 26.0 41.3 70.8 6.46 8.07 9.66 11.251.64 22 56.02 2.206 36 91.67 3.609 1069 6.7 12.4 19.7 33.7 4.83 6.42 7.21 8.00 9.58 11.16 12.74 14.31 15.89
1.65 34 86.58 3.409 56 142.60 5.614 1063 10.7 19.7 31.4 53.8 4.59 5.40 7.00 8.59 10.18 11.76 13.34
1.67 48 122.23 4.812 80 203.72 8.020 1050 15.5 28.5 45.3 77.7 7.06 8.67 10.27
1.67 24 61.12 2.406 40 101.86 4.010 1050 7.4 13.6 21.6 37.0 4.33 5.93 6.72 7.52 9.10 10.68 12.26 13.83 15.41
1.68 38 96.77 3.810 64 162.97 6.416 1039 12.1 22.2 35.3 60.6 6.00 7.60 9.20 10.79 12.37
1.69 26 66.21 2.607 44 112.05 4.411 1034 8.1 14.8 23.5 40.3 3.83 5.44 6.23 7.03 8.61 10.20 11.78 13.35 14.93
1.71 28 71.30 2.807 48 122.23 4.812 1021 8.7 16.0 25.5 43.7 4.94 5.74 6.54 8.13 9.71 11.29 12.87 14.45
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
49
16.37 17.95 18.42 19.52 22.67 25.82 28.97 29.76 33.70 37.63 41.57 45.51 49.45 54.33 58.90 65.19 80.94
17.79 19.37 19.84 20.94 24.09 27.24 30.39 31.18 35.12 39.05 42.99 46.93 50.86 55.75 60.31 66.61 82.36
15.27 16.84 17.31 18.42 21.57 24.72 27.87 28.66 32.59 36.53 40.47 44.41 48.34 53.22 57.79 64.09 79.84
14.16 15.74 16.21 17.31 20.46 23.61 26.76 27.55 31.49 35.43 39.36 43.30 47.24 52.12 56.69 62.99 78.74
16.69 18.26 18.73 19.84 22.99 26.14 29.29 30.07 34.01 37.95 41.89 45.82 49.76 54.64 59.21 65.51 81.26
18.11 19.68 20.15 21.26 24.41 27.56 30.71 31.49 35.43 39.37 43.30 47.24 51.18 56.06 60.63 66.93 82.68
11.94 13.52 13.99 15.10 18.25 21.40 24.55 25.34 29.28 33.22 37.16 41.09 45.03 49.91 54.48 60.78 76.53
15.90 17.47 17.94 19.05 22.20 25.35 28.50 29.29 33.22 37.16 41.10 45.04 48.97 53.85 58.42 64.72 80.47
17.00 18.58 19.05 20.15 23.30 26.45 29.60 30.39 34.33 38.26 42.20 46.14 50.08 54.96 59.53 65.82 81.57
17.32 18.89 19.36 20.47 23.62 26.77 29.92 30.70 34.64 38.58 42.52 46.45 50.39 55.27 59.84 66.14 81.89
13.20 14.78 15.25 16.36 19.51 22.66 25.81 26.60 30.54 34.48 38.42 42.35 46.29 51.17 55.74 62.04 77.79
15.42 17.00 17.47 18.57 21.72 24.87 28.02 28.81 32.75 36.69 40.62 44.56 48.50 53.38 57.95 64.25 80.00
16.53 18.10 18.57 19.68 22.83 25.98 29.13 29.92 33.85 37.79 41.73 45.67 49.60 54.48 59.05 65.35 81.10
17.63 19.21 19.68 20.78 23.93 27.08 30.23 31.02 34.96 38.89 42.83 46.77 50.71 55.59 60.16 66.45 82.20
16.84 18.42 18.89 19.99 23.14 26.29 29.44 30.23 34.17 38.11 42.04 45.98 49.92 54.80 59.37 65.67 81.41
17.95 19.52 19.99 21.10 24.25 27.40 30.55 31.33 35.27 39.21 43.15 47.08 51.02 55.90 60.47 66.77 82.52
16.05 17.63 18.10 19.20 22.35 25.50 28.65 29.44 33.38 37.32 41.25 45.19 49.13 54.01 58.58 64.88 80.63
17.16 18.73 19.20 20.31 23.46 26.61 29.76 30.55 34.48 38.42 42.36 46.30 50.23 55.11 59.68 65.98 81.73
9.95 13.13 16.30 19.46 20.25 24.20 28.14 32.08 36.03 39.97 44.85 49.42 55.72 71.48
14.47 16.04 16.52 17.62 20.77 23.92 27.07 27.86 31.80 35.74 39.68 43.61 47.55 52.43 57.00 63.30 79.05
9.83 11.42 11.90 13.00 16.17 19.33 22.48 23.27 27.21 31.15 35.09 39.03 42.97 47.86 52.42 58.72 74.48
15.57 17.15 17.62 18.73 21.88 25.03 28.18 28.97 32.90 36.84 40.78 44.72 48.66 53.54 58.10 64.40 80.15
17.47 19.05 19.52 20.62 23.77 26.92 30.07 30.86 34.80 38.74 42.67 46.61 50.55 55.43 60.00 66.30 82.04
11.27 12.86 13.33 14.44 17.60 20.75 23.91 24.69 28.64 32.58 36.52 40.45 44.39 49.28 53.84 60.15 75.90
16.68 18.26 18.73 19.83 22.98 26.13 29.28 30.07 34.01 37.95 41.88 45.82 49.76 54.64 59.21 65.51 81.26
13.51 15.08 15.56 16.66 19.82 22.97 26.12 26.91 30.85 34.79 38.73 42.66 46.60 51.49 56.05 62.35 78.10
17.79 19.36 19.84 20.94 24.09 27.24 30.39 31.18 35.11 39.05 42.99 46.93 50.86 55.74 60.31 66.61 82.36
17.00 18.57 19.04 20.15 23.30 26.45 29.60 30.39 34.32 38.26 42.20 46.14 50.07 54.96 59.52 65.82 81.57
14.62 16.19 16.67 17.77 20.92 24.08 27.23 28.02 31.95 35.89 39.83 43.77 47.71 52.59 57.16 63.46 79.21
16.20 17.78 18.25 19.36 22.51 25.66 28.81 29.60 33.53 37.47 41.41 45.35 49.29 54.17 58.73 65.03 80.78
12.54 14.12 14.60 15.70 18.86 22.01 25.17 25.96 29.90 33.84 37.78 41.71 45.65 50.54 55.10 61.41 77.16
15.73 17.30 17.78 18.88 22.03 25.18 28.33 29.12 33.06 37.00 40.94 44.87 48.81 53.69 58.26 64.56 80.31
17.31 18.89 19.36 20.46 23.61 26.76 29.91 30.70 34.64 38.58 42.51 46.45 50.39 55.27 59.84 66.14 81.89
16.83 18.41 18.88 19.99 23.14 26.29 29.44 30.23 34.16 38.10 42.04 45.98 49.92 54.80 59.36 65.66 81.41
17.63 19.20 19.67 20.78 23.93 27.08 30.23 31.02 34.95 38.89 42.83 46.77 50.70 55.59 60.15 66.45 82.20
9.39 10.52 13.71 16.89 20.06 20.85 24.80 28.75 32.69 36.64 40.58 45.47 50.04 56.34 72.10
14.77 16.35 16.82 17.92 21.08 24.23 27.38 28.17 32.11 36.05 39.99 43.92 47.86 52.75 57.31 63.61 79.36
16.36 17.93 18.41 19.51 22.66 25.81 28.96 29.75 33.69 37.63 41.57 45.50 49.44 54.32 58.89 65.19 80.94
17.15 18.73 19.20 20.30 23.45 26.60 29.75 30.54 34.48 38.42 42.36 46.29 50.23 55.11 59.68 65.98 81.73
13.81 15.39 15.86 16.96 20.12 23.28 26.43 27.22 31.16 35.10 39.04 42.97 46.91 51.80 56.36 62.67 78.42
15.88 17.46 17.93 19.03 22.19 25.34 28.49 29.28 33.22 37.15 41.09 45.03 48.97 53.85 58.42 64.72 80.47
10.41 12.00 12.48 13.59 16.76 19.93 23.09 23.88 27.82 31.76 35.71 39.65 43.59 48.47 53.04 59.34 75.10
12.84 14.42 14.89 16.00 19.16 22.32 25.47 26.26 30.20 34.14 38.08 42.02 45.96 50.85 55.41 61.72 77.4717.47 19.04 19.51 20.62 23.77 26.92 30.07 30.86 34.79 38.73 42.67 46.61 50.55 55.43 59.99 66.29 82.04
14.92 16.50 16.97 18.08 21.23 24.38 27.54 28.32 32.26 36.20 40.14 44.08 48.02 52.90 57.47 63.77 79.52
11.86 13.45 13.92 15.03 18.20 21.36 24.51 25.30 29.25 33.19 37.13 41.07 45.01 49.89 54.46 60.77 76.52
16.99 18.56 19.04 20.14 23.29 26.44 29.59 30.38 34.32 38.26 42.20 46.13 50.07 54.95 59.52 65.82 81.57
13.95 15.53 16.01 17.11 20.27 23.43 26.58 27.37 31.31 35.25 39.19 43.13 47.07 51.95 56.52 62.82 78.57
16.51 18.09 18.56 19.66 22.82 25.97 29.12 29.91 33.85 37.78 41.72 45.66 49.60 54.48 59.05 65.35 81.10
16.03 17.61 18.08 19.19 22.34 25.49 28.64 29.43 33.37 37.31 41.25 45.19 49.12 54.01 58.57 64.87 80.62
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
COMBINATIONS DRIVEN SPEEDS & HP RATINGS DRIVER DRIVEN 1750 RPM DRIVER
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 12 22 35 60
50
BELT LENGTH CODE (MM)480 560 600 640 720 800 880 960 1040
NUMBER OF BELT TEETH60 70 75 80 90 100 110 120 130
BELT LENGTH CORRECTION FACTOR (KL)0.8 0.8 0.8 0.9 0.9 0.9 0.9 1 1
1.73 22 56.02 2.206 38 96.77 3.810 1013 6.7 12.4 19.7 33.7 4.65 6.25 7.04 7.83 9.41 10.99 12.57 14.15 15.73
1.75 64 162.97 6.416 112 285.21 11.229 1000 21.0 38.6 61.4 105.3
1.75 32 81.49 3.208 56 142.60 5.614 1000 10.1 18.5 29.4 50.4 4.73 5.54 7.14 8.74 10.32 11.91 13.49
1.78 36 91.67 3.609 64 162.97 6.416 984 11.4 21.0 33.3 57.2 6.14 7.75 9.34 10.93 12.52
1.80 80 203.72 8.020 144 366.69 14.437 972 26.5 48.6 77.4 132.7
1.80 40 101.86 4.010 72 183.35 7.218 972 12.8 23.5 37.3 64.0 6.74 8.35 9.95 11.54
1.82 44 112.05 4.411 80 203.72 8.020 963 14.1 26.0 41.3 70.8 7.34 8.95 10.55
1.82 22 56.02 2.206 40 101.86 4.010 963 6.7 12.4 19.7 33.7 4.47 6.07 6.87 7.66 9.25 10.83 12.41 13.99 15.56
1.83 24 61.12 2.406 44 112.05 4.411 955 7.4 13.6 21.6 37.0 3.97 5.58 6.38 7.17 8.76 10.34 11.93 13.51 15.08
1.85 26 66.21 2.607 48 122.23 4.812 948 8.1 14.8 23.5 40.3 5.08 5.88 6.68 8.27 9.86 11.44 13.02 14.60
1.87 30 76.39 3.008 56 142.60 5.614 938 9.4 17.2 27.4 47.0 4.86 5.68 7.28 8.88 10.47 12.05 13.64
1.88 48 122.23 4.812 90 229.18 9.023 933 15.5 28.5 45.3 77.7 7.74 9.37
1.88 34 86.58 3.409 64 162.97 6.416 930 10.7 19.7 31.4 53.8 6.27 7.89 9.49 11.08 12.67
1.89 38 96.77 3.810 72 183.35 7.218 924 12.1 22.2 35.3 60.6 6.87 8.49 10.09 11.69
2.00 72 183.35 7.218 144 366.69 14.437 875 23.8 43.6 69.4 119.0
2.00 56 142.60 5.614 112 285.21 11.229 875 18.3 33.5 53.3 91.5
2.00 40 101.86 4.010 80 203.72 8.020 875 12.8 23.5 37.3 64.0 7.61 9.23 10.84
2.00 36 91.67 3.609 72 183.35 7.218 875 11.4 21.0 33.3 57.2 7.01 8.63 10.23 11.83
2.00 32 81.49 3.208 64 162.97 6.416 875 10.1 18.5 29.4 50.4 6.41 8.03 9.63 11.22 12.81
2.00 28 71.30 2.807 56 142.60 5.614 875 8.7 16.0 25.5 43.7 5.00 5.81 7.43 9.02 10.62 12.20 13.79
2.00 24 61.12 2.406 48 122.23 4.812 875 7.4 13.6 21.6 37.0 5.21 6.02 6.82 8.42 10.01 11.59 13.17 14.75
2.00 22 56.02 2.206 44 112.05 4.411 875 6.7 12.4 19.7 33.7 4.10 5.72 6.52 7.32 8.91 10.49 12.07 13.66 15.23
2.05 44 112.05 4.411 90 229.18 9.023 856 14.1 26.0 41.3 70.8 8.01 9.64
2.11 38 96.77 3.810 80 203.72 8.020 831 12.1 22.2 35.3 60.6 6.09 7.74 9.37 10.98
2.12 34 86.58 3.409 72 183.35 7.218 826 10.7 19.7 31.4 53.8 5.49 7.14 8.77 10.38 11.97
2.13 30 76.39 3.008 64 162.97 6.416 820 9.4 17.2 27.4 47.0 4.90 6.55 8.17 9.77 11.37 12.96
2.15 26 66.21 2.607 56 142.60 5.614 813 8.1 14.8 23.5 40.3 4.30 5.13 5.95 7.57 9.17 10.76 12.35 13.93
2.18 22 56.02 2.206 48 122.23 4.812 8.02 6.7 12.4 19.7 33.7 3.70 5.35 6.16 6.96 8.56 10.15 11.74 13.32 14.90
2.22 36 91.67 3.609 80 203.72 8.020 788 11.4 21.0 33.3 57.2 6.22 7.88 9.51 11.12
2.25 64 162.97 6.416 144 366.69 14.437 778 21.0 38.6 61.4 105.3
2.25 40 101.86 4.010 90 229.18 9.023 778 12.8 23.5 37.3 64.0 6.60 8.28 9.92
2.25 32 81.49 3.208 72 183.35 7.218 778 10.1 18.5 29.4 50.4 5.62 7.28 8.91 10.52 12.12
2.29 28 71.30 2.807 64 162.97 6.416 766 8.7 16.0 25.5 43.7 5.03 6.68 8.31 9.91 11.51 13.10
2.33 48 122.23 4.812 112 285.21 11.229 750 15.5 28.5 45.3 77.7
2.33 24 61.12 2.406 56 142.60 5.614 750 7.4 13.6 21.6 37.0 4.43 5.26 6.09 7.71 9.31 10.90 12.49 14.08
2.35 34 86.58 3.409 80 203.72 8.020 744 10.7 19.7 31.4 53.8 6.35 8.01 9.64 11.26
2.37 38 96.77 3.810 90 229.18 9.023 739 12.1 22.2 35.3 60.6 6.73 8.41 10.05
2.40 80 203.72 8.020 192 488.92 19.249 729 26.5 48.6 77.4 132.7
2.40 30 76.39 3.008 72 183.35 7.218 729 9.4 17.2 27.4 47.0 5.75 7.41 9.04 10.66 12.26
2.46 26 66.21 2.607 64 162.97 6.416 711 8.1 14.8 23.5 40.3 5.16 6.82 8.44 10.05 11.65 13.25
2.50 36 91.67 3.609 90 229.18 9.023 700 11.4 21.0 33.3 57.2 6.86 8.54 10.19
2.50 32 81.49 3.208 80 203.72 8.020 700 10.1 18.5 29.4 50.4 6.48 8.15 9.78 11.40
2.55 44 112.05 4.411 112 285.21 11.229 688 14.1 26.0 41.3 70.8
2.55 22 56.02 2.206 56 142.60 5.614 688 6.7 12.4 19.7 33.7 4.56 5.40 6.22 7.84 9.45 11.05 12.64 14.23
2.57 56 142.60 5.614 144 366.69 14.437 681 18.3 33.5 53.3 91.5
2.57 28 71.30 2.807 72 183.35 7.218 681 8.7 16.0 25.5 43.7 5.88 7.55 9.18 10.80 12.40
2.65 34 86.58 3.409 90 229.18 9.023 661 10.7 19.7 31.4 53.8 6.99 8.67 10.32
2.67 72 183.35 7.218 192 488.92 19.249 656 23.8 43.6 69.4 119.0
2.67 30 76.39 3.008 80 203.72 8.020 656 9.4 17.2 27.4 47.0 6.60 8.28 9.92 11.54
2.67 24 61.12 2.406 64 162.97 6.416 656 7.4 13.6 21.6 37.0 4.42 5.28 6.95 8.58 10.19 11.80 13.39
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
51
17.30 18.88 19.35 20.46 23.61 26.76 29.91 30.70 34.63 38.57 42.51 46.45 50.39 55.27 59.84 66.14 81.88
9.45 9.94 11.08 14.28 17.47 20.65 21.44 25.40 29.35 33.30 37.24 41.19 46.08 50.65 56.96 72.72
15.07 16.65 17.12 18.23 21.38 24.54 27.69 28.48 32.42 36.36 40.30 44.23 48.17 53.06 57.62 63.93 79.68
14.10 15.68 16.16 17.27 20.42 23.58 26.73 27.52 31.46 35.40 39.34 43.28 47.22 52.11 56.67 62.98 78.73
13.47 16.70 17.50 21.49 25.47 29.43 33.39 37.34 42.24 46.82 53.13 68.90
13.13 14.72 15.19 16.30 19.46 22.62 25.78 26.57 30.51 34.45 38.39 42.33 46.27 51.16 55.72 62.03 77.78
12.15 13.74 14.22 15.33 18.49 21.66 24.82 25.61 29.55 33.49 37.44 41.38 45.32 50.20 54.77 61.08 76.83
17.14 18.72 19.19 20.29 23.45 26.60 29.75 30.54 34.48 38.41 42.35 46.29 50.23 55.11 59.68 65.98 81.73
16.66 18.24 18.71 19.82 22.97 26.12 29.27 30.06 34.00 37.94 41.88 45.82 49.75 54.64 59.20 65.50 81.25
16.18 17.76 18.23 19.34 22.49 25.64 28.80 29.58 33.52 37.46 41.40 45.34 49.28 54.16 58.73 65.03 80.78
15.22 16.80 17.27 18.38 21.53 24.69 27.84 28.63 32.57 36.51 40.45 44.39 48.33 53.21 57.78 64.08 79.83
10.98 12.58 13.06 14.17 17.35 20.52 23.69 24.48 28.43 32.37 36.32 40.26 44.20 49.09 53.66 59.96 75.72
14.25 15.83 16.31 17.41 20.57 23.73 26.89 27.67 31.62 35.56 39.50 43.44 47.38 52.26 56.83 63.13 78.88
13.28 14.86 15.34 16.45 19.61 22.77 25.93 26.72 30.66 34.60 38.54 42.48 46.42 51.31 55.88 62.18 77.93
14.02 17.26 18.06 22.07 26.05 30.02 33.98 37.94 42.84 47.42 53.74 69.51
10.00 10.49 11.63 14.85 18.05 21.23 22.02 25.99 29.95 33.90 37.85 41.79 46.69 51.26 57.57 73.33
12.44 14.03 14.51 15.62 18.79 21.96 25.12 25.91 29.85 33.80 37.74 41.68 45.62 50.51 55.08 61.38 77.14
13.42 15.01 15.48 16.59 19.76 22.92 26.08 26.87 30.81 34.76 38.70 42.64 46.58 51.46 56.03 62.34 78.09
14.40 15.98 16.46 17.56 20.72 23.88 27.04 27.83 31.77 35.71 39.65 43.59 47.53 52.42 56.98 63.29 79.04
15.37 16.95 17.42 18.53 21.69 24.84 28.00 28.78 32.73 36.67 40.61 44.54 48.48 53.37 57.94 64.24 79.99
16.33 17.91 18.39 19.49 22.64 25.80 28.95 29.74 33.68 37.62 41.56 45.50 49.43 54.32 58.88 65.19 80.94
16.81 18.39 18.86 19.97 23.12 26.27 29.43 30.21 34.15 38.09 42.03 45.97 49.91 54.79 59.36 65.66 81.41
11.26 12.86 13.34 14.46 17.64 20.82 23.98 24.77 28.73 32.67 36.62 40.56 44.51 49.39 53.97 60.27 76.03
12.58 14.17 14.65 15.76 18.94 22.10 25.27 26.06 30.00 33.95 37.89 41.84 45.78 50.66 55.23 61.54 77.29
13.57 15.15 15.63 16.74 19.91 23.07 26.23 27.02 30.96 34.91 38.85 42.79 46.73 51.62 56.19 62.49 78.24
14.54 16.13 16.60 17.71 20.87 24.03 27.19 27.98 31.92 35.86 39.81 43.75 47.69 52.57 57.14 63.44 79.19
15.52 17.10 17.57 18.68 21.84 24.99 28.15 28.94 32.88 36.82 40.76 44.70 48.64 53.52 58.09 64.39 80.14
16.48 18.06 18.54 19.64 22.80 25.95 29.10 29.89 33.83 37.77 41.71 45.65 49.59 54.47 59.04 65.34 81.09
12.72 14.32 14.80 15.91 19.08 22.25 25.42 26.21 30.16 34.10 38.05 41.99 45.93 50.82 55.39 61.69 77.45
11.24 14.56 17.81 18.62 22.63 26.63 30.60 34.57 38.53 43.44 48.02 54.34 70.12
11.54 13.15 13.63 14.75 17.93 21.11 24.28 25.07 29.02 32.97 36.92 40.87 44.81 49.70 54.27 60.58 76.34
13.71 15.30 15.78 16.89 20.06 23.22 26.38 27.17 31.12 35.06 39.00 42.94 46.89 51.77 56.34 62.64 78.40
14.69 16.28 16.75 17.86 21.02 24.18 27.34 28.13 32.07 36.02 39.96 43.90 47.84 52.72 57.29 63.60 79.35
8.86 10.53 11.02 12.17 15.41 18.62 21.81 22.61 26.58 30.54 34.50 38.45 42.40 47.29 51.87 58.18 73.95
15.67 17.25 17.72 18.83 21.99 25.15 28.30 29.09 33.03 36.97 40.91 44.85 48.79 53.68 58.24 64.55 80.30
12.86 14.46 14.94 16.05 19.23 22.40 25.56 26.35 30.31 34.25 38.20 42.14 46.08 50.97 55.54 61.85 77.60
11.68 13.29 13.77 14.89 18.08 21.26 24.43 25.22 29.17 33.12 37.07 41.02 44.96 49.85 54.42 60.73 76.49
17.02 21.14 25.20 29.22 33.22 38.17 42.78 49.13 64.95
13.85 15.45 15.92 17.03 20.20 23.37 26.53 27.32 31.27 35.21 39.16 43.10 47.04 51.92 56.50 62.80 78.55
14.84 16.42 16.90 18.01 21.17 24.33 27.49 28.28 32.23 36.17 40.11 44.05 47.99 52.88 57.45 63.75 79.50
11.81 13.43 13.91 15.03 18.22 21.40 24.57 25.37 29.32 33.27 37.22 41.17 45.11 50.00 54.58 60.88 76.64
13.00 14.60 15.08 16.20 19.38 22.55 25.71 26.50 30.46 34.40 38.35 42.29 46.24 51.12 55.70 62.00 77.76
9.12 10.79 11.29 12.44 15.69 18.90 22.10 22.89 26.87 30.83 34.79 38.75 42.70 47.59 52.17 58.48 74.25
15.81 17.40 17.87 18.98 22.14 25.30 28.45 29.24 33.18 37.13 41.07 45.01 48.95 53.83 58.40 64.70 80.45
11.76 15.10 18.36 19.17 23.20 27.20 31.18 35.16 39.12 44.03 48.62 54.94 70.73
14.00 15.59 16.07 17.18 20.35 23.52 26.68 27.47 31.42 35.36 39.31 43.25 47.19 52.08 56.65 62.95 78.71
11.95 13.57 14.05 15.17 18.37 21.55 24.72 25.51 29.47 33.42 37.37 41.32 45.27 50.16 54.73 61.04 76.80
13.25 17.54 21.68 25.75 29.78 33.79 38.74 43.36 49.71 65.55
13.15 14.75 15.23 16.34 19.52 22.70 25.86 26.65 30.61 34.55 38.50 42.44 46.39 51.28 55.85 62.15 77.91
14.98 16.57 17.05 18.16 21.32 24.48 27.64 28.43 32.38 36.32 40.26 44.21 48.15 53.03 57.60 63.90 79.66
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
COMBINATIONS DRIVEN SPEEDS & HP RATINGS DRIVER DRIVEN 1750 RPM DRIVER
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 12 22 35 60
52
BELT LENGTH CODE (MM)480 560 600 640 720 800 880 960 1040
NUMBER OF BELT TEETH60 70 75 80 90 100 110 120 130
BELT LENGTH CORRECTION FACTOR (KL)0.8 0.8 0.8 0.9 0.9 0.9 0.9 1 1
2.77 26 66.21 2.607 72 183.35 7.218 632 8.1 14.8 23.5 40.3 6.01 7.68 9.32 10.94 12.54
2.80 40 101.86 4.010 112 285.21 11.229 625 12.8 23.5 37.3 64.0 7.63
2.81 32 81.49 3.208 90 229.18 9.023 622 10.1 18.5 29.4 50.4 7.11 8.81 10.46
2.86 28 71.30 2.807 80 203.72 8.020 613 8.7 16.0 25.5 43.7 6.73 8.41 10.05 11.68
2.91 22 56.02 2.206 64 162.97 6.416 602 6.7 12.4 19.7 33.7 4.54 5.41 7.09 8.72 10.33 11.94 13.54
2.95 38 96.77 3.810 112 285.21 11.229 594 12.1 22.2 35.3 60.6 7.76
3.00 64 162.97 6.416 192 488.92 19.249 583 21.0 38.6 61.4 105.3
3.00 48 122.23 4.812 144 366.69 14.437 583 15.5 28.5 45.3 77.7
3.00 30 76.39 3.008 90 229.18 9.023 583 9.4 17.2 27.4 47.0 7.24 8.94 10.59
3.00 24 61.12 2.406 72 183.35 7.218 583 7.4 13.6 21.6 37.0 6.14 7.82 9.46 11.08 12.68
3.08 26 66.21 2.607 80 203.72 8.020 569 8.1 14.8 23.5 40.3 6.86 8.54 10.19 11.81
3.11 36 91.67 3.609 112 285.21 11.229 563 11.4 21.0 33.3 57.2 7.88
3.21 28 71.30 2.807 90 229.18 9.023 544 8.7 16.0 25.5 43.7 7.36 9.07 10.73
3.27 44 112.05 4.411 144 366.69 14.437 535 14.1 26.0 41.3 70.8
3.27 22 56.02 2.206 72 183.35 7.218 535 6.7 12.4 19.7 33.7 6.26 7.95 9.59 11.21 12.82
3.29 34 86.58 3.409 112 285.21 11.229 531 10.7 19.7 31.4 53.8 8.00
3.33 24 61.12 2.406 80 203.72 8.020 525 7.4 13.6 21.6 37.0 6.99 8.68 10.32 11.953.43 56 142.60 5.614 192 488.92 19.249 510 18.3 33.5 53.3 91.5
3.46 26 66.21 2.607 90 229.18 9.023 506 8.1 14.8 23.5 40.3 7.49 9.20 10.86
3.50 32 81.49 3.208 112 285.21 11.229 500 10.1 18.5 29.4 50.4 8.12
3.60 40 101.86 4.010 144 366.69 14.437 486 12.8 23.5 37.3 64.0
3.64 22 56.02 2.206 80 203.72 8.020 481 6.7 12.4 19.7 33.7 5.33 7.11 8.81 10.46 12.09
3.73 30 76.39 3.008 112 285.21 11.229 469 9.4 17.2 27.4 47.0 8.24
3.75 24 61.12 2.406 90 229.18 9.023 467 7.4 13.6 21.6 37.0 5.80 7.62 9.33 10.99
3.79 38 96.77 3.810 144 366.69 14.437 462 12.1 22.2 35.3 60.6
4.00 48 122.23 4.812 192 488.92 19.249 438 15.5 28.5 45.3 77.7
4.00 36 91.67 3.609 144 366.69 14.437 438 11.4 21.0 33.3 57.2
4.00 28 71.30 2.807 112 285.21 11.229 438 8.7 16.0 25.5 43.7 8.36
4.09 22 56.02 2.206 90 229.18 9.023 428 6.7 12.4 19.7 33.7 5.92 7.74 9.46 11.13
4.24 34 86.58 3.409 144 366.69 14.437 413 10.7 19.7 31.4 53.8
4.31 26 66.21 2.607 112 285.21 11.229 406 8.1 14.8 23.5 40.3 8.484.36 44 112.05 4.411 192 488.92 19.249 401 14.1 26.0 41.3 70.8
4.50 32 81.49 3.208 144 366.69 14.437 389 10.1 18.5 29.4 50.4
4.67 24 61.12 2.406 112 285.21 11.229 375 7.4 13.6 21.6 37.0 8.60
4.80 40 101.86 4.010 192 488.92 19.249 365 12.8 23.5 37.3 64.0
4.80 30 76.39 3.008 144 366.69 14.437 365 9.4 17.2 27.4 47.0
5.05 38 96.77 3.810 192 488.92 19.249 346 12.1 22.2 35.3 60.65.09 22 56.02 2.206 112 285.21 11.229 344 6.7 12.4 19.7 33.7 6.78 8.72
5.14 28 71.30 2.807 144 366.69 14.437 340 8.7 16.0 25.5 43.7
5.33 36 91.67 3.609 192 488.92 19.249 328 11.4 21.0 33.3 57.2
5.54 26 66.21 2.607 144 366.69 14.437 316 8.1 14.8 23.5 40.3
5.65 34 86.58 3.409 192 488.92 19.249 310 10.7 19.7 31.4 53.8
6.00 32 81.49 3.208 192 488.92 19.249 292 10.1 18.5 29.4 50.4
6.00 24 61.12 2.406 144 366.69 14.437 292 7.4 13.6 21.6 37.0
6.40 30 76.39 3.008 192 488.92 19.249 273 9.4 17.2 27.4 47.0
6.55 22 56.02 2.206 144 366.69 14.437 267 6.7 12.4 19.7 33.7
6.86 28 71.30 2.807 192 488.92 19.249 255 8.7 16.0 25.5 43.7
7.38 26 66.21 2.607 192 488.92 19.249 237 8.1 14.8 23.5 40.3
8.00 24 61.12 2.406 192 488.92 19.249 219 7.4 13.6 21.6 37.0
8.73 22 56.02 2.206 192 488.92 19.249 201 6.7 12.4 19.7 33.7
RPP PANTHER ULTRA-CORD BELT 8mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
53
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)1120 1200 1224 1280 1440 1600 1760 1800 2000 2200 2400 2600 2800 3048 3280 3600 4400
NUMBER OF BELT TEETH140 150 153 160 180 200 220 225 250 275 300 325 350 381 410 450 550
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)1 1 1 1.1 1.1 1.1 1.2 1.2 1.2 1.2 1.3 1.3 1.4 1.4 1.4 1.5 1.5
14.14 15.74 16.21 17.33 20.50 23.67 26.83 27.62 31.57 35.51 39.46 43.40 47.34 52.23 56.80 63.11 78.86
9.37 11.06 11.56 12.71 15.97 19.19 22.38 23.18 27.16 31.13 35.09 39.04 43.00 47.89 52.47 58.79 74.56
12.09 13.71 14.19 15.31 18.51 21.69 24.87 25.66 29.62 33.57 37.52 41.47 45.42 50.31 54.88 61.19 76.95
13.29 14.89 15.37 16.49 19.67 22.84 26.01 26.80 30.76 34.70 38.65 42.60 46.54 51.43 56.00 62.31 78.07
15.13 16.72 17.19 18.30 21.47 24.63 27.79 28.58 32.53 36.47 40.42 44.36 48.30 53.19 57.76 64.06 79.81
9.50 11.19 11.69 12.84 16.10 19.33 22.53 23.32 27.31 31.27 35.24 39.19 43.15 48.04 52.62 58.94 74.71
12.85 13.75 18.06 22.22 26.30 30.34 34.36 39.32 43.94 50.30 66.14
12.27 15.63 18.91 19.72 23.76 27.77 31.76 35.74 39.71 44.62 49.21 55.54 71.33
12.23 13.84 14.33 15.45 18.65 21.84 25.01 25.81 29.77 33.72 37.67 41.62 45.57 50.46 55.03 61.34 77.11
14.28 15.88 16.36 17.47 20.65 23.81 26.98 27.77 31.72 35.67 39.61 43.55 47.50 52.39 56.96 63.26 79.02
13.43 15.03 15.51 16.63 19.81 22.99 26.16 26.95 30.90 34.85 38.80 42.75 46.69 51.58 56.15 62.46 78.22
9.63 11.32 11.82 12.98 16.24 19.47 22.67 23.47 27.45 31.42 35.38 39.34 43.30 48.19 52.77 59.09 74.86
12.36 13.98 14.47 15.59 18.80 21.98 25.16 25.95 29.92 33.87 37.82 41.77 45.72 50.61 55.19 61.50 77.26
12.53 15.89 19.18 20.00 24.04 28.05 32.05 36.03 40.00 44.92 49.51 55.84 71.63
14.43 16.02 16.50 17.62 20.79 23.96 27.13 27.92 31.87 35.82 39.76 43.71 47.65 52.54 57.11 63.41 79.17
9.76 11.45 11.95 13.11 16.38 19.61 22.81 23.61 27.60 31.57 35.53 39.49 43.44 48.34 52.92 59.24 75.01
13.57 15.17 15.65 16.77 19.96 23.14 26.31 27.10 31.05 35.00 38.95 42.90 46.84 51.73 56.31 62.61 78.3713.33 14.24 18.58 22.75 26.85 30.90 34.92 39.89 44.52 50.88 66.74
12.50 14.12 14.61 15.73 18.94 22.13 25.31 26.10 30.06 34.02 37.97 41.92 45.87 50.76 55.34 61.65 77.41
9.88 11.58 12.08 13.25 16.52 19.75 22.95 23.75 27.74 31.71 35.68 39.64 43.59 48.49 53.08 59.39 75.17
12.78 16.16 19.45 20.27 24.32 28.34 32.33 36.32 40.29 45.21 49.80 56.13 71.94
13.71 15.31 15.79 16.91 20.10 23.28 26.45 27.25 31.20 35.15 39.10 43.05 47.00 51.89 56.46 62.77 78.53
10.01 11.71 12.21 13.38 16.65 19.89 23.10 23.90 27.88 31.86 35.83 39.79 43.74 48.64 53.23 59.54 75.32
12.63 14.26 14.74 15.87 19.08 22.27 25.45 26.25 30.21 34.17 38.12 42.07 46.02 50.92 55.49 61.80 77.57
9.30 12.90 16.29 19.59 20.41 24.46 28.48 32.48 36.46 40.44 45.36 49.95 56.28 72.09
13.81 14.73 19.09 23.28 27.39 31.45 35.48 40.46 45.09 51.46 67.33
9.42 13.03 16.42 19.72 20.54 24.60 28.62 32.62 36.61 40.58 45.50 50.10 56.43 72.24
10.13 11.84 12.34 13.51 16.79 20.03 23.24 24.04 28.03 32.01 35.97 39.93 43.89 48.79 53.38 59.69 75.47
12.77 14.40 14.88 16.01 19.22 22.42 25.60 26.39 30.36 34.32 38.27 42.22 46.17 51.07 55.64 61.95 77.72
9.54 13.16 16.55 19.86 20.68 24.74 28.76 32.76 36.75 40.73 45.65 50.25 56.58 72.39
10.26 11.97 12.47 13.64 16.93 20.17 23.38 24.18 28.17 32.15 36.12 40.08 44.04 48.94 53.53 59.84 75.6214.05 14.97 19.35 23.55 27.66 31.73 35.76 40.74 45.38 51.75 67.62
9.65 13.28 16.68 19.99 20.81 24.87 28.90 32.90 36.89 40.87 45.80 50.39 56.73 72.54
10.39 12.10 12.60 13.77 17.06 20.31 23.52 24.32 28.32 32.30 36.27 40.23 44.19 49.09 53.68 59.99 75.78
14.29 15.21 19.60 23.81 27.93 32.00 36.04 41.02 45.66 52.04 67.92
9.77 13.41 16.81 20.13 20.95 25.01 29.04 33.05 37.04 41.02 45.94 50.54 56.88 72.69
14.41 15.33 19.73 23.94 28.06 32.14 36.18 41.16 45.80 52.18 68.0610.51 12.23 12.73 13.91 17.20 20.44 23.66 24.46 28.46 32.44 36.41 40.38 44.34 49.24 53.83 60.14 75.93
9.89 13.53 16.94 20.26 21.08 25.15 29.18 33.19 37.18 41.16 46.09 50.69 57.03 72.84
14.53 15.46 19.86 24.07 28.20 32.28 36.32 41.30 45.95 52.33 68.21
8.57 10.00 13.66 17.07 20.39 21.22 25.29 29.32 33.33 37.32 41.31 46.23 50.84 57.17 72.99
14.65 15.58 19.98 24.20 28.33 32.41 36.46 41.44 46.09 52.47 68.36
14.77 15.70 20.11 24.33 28.47 32.55 36.60 41.59 46.23 52.62 68.50
8.68 10.12 13.78 17.20 20.53 21.35 25.43 29.46 33.47 37.47 41.45 46.38 50.98 57.32 73.14
14.89 15.82 20.24 24.46 28.60 32.69 36.74 41.73 46.37 52.76 68.65
8.79 10.24 13.91 17.33 20.66 21.48 25.56 29.60 33.61 37.61 41.60 46.52 51.13 57.47 73.29
15.01 15.94 20.36 24.60 28.74 32.82 36.87 41.87 46.51 52.90 68.80
11.00 15.13 16.06 20.49 24.73 28.87 32.96 37.01 42.01 46.66 53.05 68.94
11.11 15.25 16.18 20.62 24.86 29.00 33.10 37.15 42.15 46.80 53.19 69.09
11.21 15.36 16.30 20.74 24.99 29.14 33.23 37.29 42.29 46.94 53.33 69.24
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
54
SPROCKET COMBINATIONS 1750 DRIVER RPM 1160 DRIVER RPMDRIVER DRIVEN HORSEPOWER RATING HORSEPOWER RATING
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm) DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 20 42 65 90 120 SPEED 20 42 65 90 120
1.00 80 356.51 14.036 80 356.51 14.036 1750 124.20 261.12 404.27 559.86 746.57 1160 97.34 204.63 316.80 438.72 585.03
1.00 72 320.86 12.632 72 320.86 12.632 1750 114.00 239.67 371.06 513.87 685.24 1160 88.19 185.40 287.03 397.50 530.06
1.00 68 303.03 11.93 68 303.03 11.93 1750 108.62 228.36 353.55 489.62 652.90 1160 83.54 175.62 271.89 376.53 502.10
1.00 64 285.21 11.229 64 285.21 11.229 1750 103.07 216.70 335.49 464.61 619.55 1160 78.84 165.75 256.60 355.36 473.87
1.00 60 267.38 10.527 60 267.38 10.527 1750 97.36 204.69 316.90 438.86 585.21 1160 74.10 155.77 241.16 333.97 445.34
1.00 56 249.55 9.825 56 249.55 9.825 1750 91.50 192.37 297.82 412.44 549.98 1160 69.31 145.71 225.58 312.39 416.57
1.00 52 231.73 9.123 52 231.73 9.123 1750 85.51 179.76 278.29 385.40 513.93 1160 64.49 135.57 209.88 290.66 387.59
1.00 48 213.9 8.421 48 213.9 8.421 1750 79.38 166.87 258.34 357.77 477.08 1160 59.63 125.35 194.07 268.75 358.38
1.00 44 196.08 7.72 44 196.08 7.72 1750 73.13 153.74 238.02 329.62 439.55 1160 54.74 115.07 178.15 246.71 328.99
1.00 40 178.25 7.018 40 178.25 7.018 1750 66.78 140.38 217.34 300.98 401.35 1160 49.82 104.73 162.14 224.54 299.42
1.00 38 169.34 6.667 38 169.34 6.667 1750 63.57 133.63 206.88 286.50 382.05 1160 47.35 99.54 154.10 213.41 284.58
1.00 36 160.43 6.316 36 160.43 6.316 1750 60.33 126.83 196.35 271.92 362.60 1160 44.88 94.34 146.05 202.26 269.71
1.00 34 151.52 5.965 34 151.52 5.965 1750 57.07 119.99 185.76 257.24 343.03 1160 42.40 89.13 137.98 191.08 254.81
1.00 32 142.6 5.614 32 142.6 5.614 1750 53.80 113.09 175.08 242.46 323.32 1160 39.91 83.90 129.89 179.87 239.86
1.00 30 133.69 5.263 30 133.69 5.263 1750 50.50 106.16 164.36 227.61 303.52 1160 37.42 78.67 121.79 168.66 224.90
1.00 29 129.23 5.088 29 129.23 5.088 1750 48.85 102.68 158.97 220.15 293.57 1160 36.17 76.04 117.73 163.03 217.40
1.00 28 124.78 4.912 28 124.78 4.912 1750 47.19 99.20 153.58 212.69 283.61 1160 34.93 73.43 113.67 157.42 209.92
1.03 29 129.23 5.088 30 133.69 5.263 1692 48.85 102.68 158.97 220.15 293.57 1121 36.17 76.04 117.73 163.03 217.40
1.04 28 124.78 4.912 29 129.23 5.088 1690 47.19 99.20 153.58 212.69 283.61 1120 34.93 73.43 113.67 157.42 209.92
1.05 38 169.34 6.667 40 178.25 7.018 1663 63.57 133.63 206.88 286.50 382.05 1102 47.35 99.54 154.10 213.41 284.58
1.06 36 160.43 6.316 38 169.34 6.667 1658 60.33 126.83 196.35 271.92 362.60 1099 44.88 94.34 146.05 202.26 269.71
1.06 68 303.03 11.93 72 320.86 12.632 1653 108.62 228.36 353.55 489.62 652.90 1096 83.54 175.62 271.89 376.53 502.10
1.06 34 151.52 5.965 36 160.43 6.316 1653 57.07 119.99 185.76 257.24 343.03 1096 42.40 89.13 137.98 191.08 254.81
1.06 64 285.21 11.229 68 303.03 11.93 1647 103.07 216.70 335.49 464.61 619.55 1092 78.84 165.75 256.60 355.36 473.87
1.06 32 142.6 5.614 34 151.52 5.965 1647 53.80 113.09 175.08 242.46 323.32 1092 39.91 83.90 129.89 179.87 239.86
1.07 60 267.38 10.527 64 285.21 11.229 1641 97.36 204.69 316.90 438.86 585.21 1088 74.10 155.77 241.16 333.97 445.34
1.07 30 133.69 5.263 32 142.6 5.614 1641 50.50 106.16 164.36 227.61 303.52 1088 37.42 78.67 121.79 168.66 224.90
1.07 56 249.55 9.825 60 267.38 10.527 1633 91.50 192.37 297.82 412.44 549.98 1083 69.31 145.71 225.58 312.39 416.57
1.07 28 124.78 4.912 30 133.69 5.263 1633 47.19 99.20 153.58 212.69 283.61 1083 34.93 73.43 113.67 157.42 209.92
1.08 52 231.73 9.123 56 249.55 9.825 1625 85.51 179.76 278.29 385.40 513.93 1077 64.49 135.57 209.88 290.66 387.59
1.08 48 213.9 8.421 52 231.73 9.123 1615 79.38 166.87 258.34 357.77 477.08 1071 59.63 125.35 194.07 268.75 358.38
1.09 44 196.08 7.72 48 213.9 8.421 1604 73.13 153.74 238.02 329.62 439.55 1063 54.74 115.07 178.15 246.71 328.99
1.1 40 178.25 7.018 44 196.08 7.72 1591 66.78 140.38 217.34 300.98 401.35 1055 49.82 104.73 162.14 224.54 299.42
1.1 29 129.23 5.088 32 142.6 5.614 1586 48.85 102.68 158.97 220.15 293.57 1051 36.17 76.04 117.73 163.03 217.40
1.11 72 320.86 12.632 80 356.51 14.036 1575 114.00 239.67 371.06 513.87 685.24 1044 88.19 185.40 287.03 397.50 530.06
1.11 36 160.43 6.316 40 178.25 7.018 1575 60.33 126.83 196.35 271.92 362.60 1044 44.88 94.34 146.05 202.26 269.71
1.12 34 151.52 5.965 38 169.34 6.667 1566 57.07 119.99 185.76 257.24 343.03 1038 42.40 89.13 137.98 191.08 254.81
1.13 64 285.21 11.229 72 320.86 12.632 1556 103.07 216.70 335.49 464.61 619.55 1031 78.84 165.75 256.60 355.36 473.87
1.13 32 142.6 5.614 36 160.43 6.316 1556 53.80 113.09 175.08 242.46 323.32 1031 39.91 83.90 129.89 179.87 239.86
1.13 80 356.51 14.036 90 401.07 15.79 1556 124.20 261.12 404.27 559.86 746.57 1031 97.34 204.63 316.80 438.72 585.03
1.13 60 267.38 10.527 68 303.03 11.93 1544 97.36 204.69 316.90 438.86 585.21 1024 74.10 155.77 241.16 333.97 445.34
1.13 30 133.69 5.263 34 151.52 5.965 1544 50.50 106.16 164.36 227.61 303.52 1024 37.42 78.67 121.79 168.66 224.90
1.14 56 249.55 9.825 64 285.21 11.229 1531 91.50 192.37 297.82 412.44 549.98 1015 69.31 145.71 225.58 312.39 416.57
1.14 28 124.78 4.912 32 142.6 5.614 1531 47.19 99.20 153.58 212.69 283.61 1015 34.93 73.43 113.67 157.42 209.92
1.15 52 231.73 9.123 60 267.38 10.527 1517 85.51 179.76 278.29 385.40 513.93 1005 64.49 135.57 209.88 290.66 387.591.16 38 169.34 6.667 44 196.08 7.72 1511 63.57 133.63 206.88 286.50 382.05 1002 47.35 99.54 154.10 213.41 284.58
1.17 48 213.9 8.421 56 249.55 9.825 1500 79.38 166.87 258.34 357.77 477.08 994 59.63 125.35 194.07 268.75 358.38
1.17 29 129.23 5.088 34 151.52 5.965 1493 48.85 102.68 158.97 220.15 293.57 989 36.17 76.04 117.73 163.03 217.40
1.18 68 303.03 11.93 80 356.51 14.036 1488 108.62 228.36 353.55 489.62 652.90 986 83.54 175.62 271.89 376.53 502.10
1.18 34 151.52 5.965 40 178.25 7.018 1488 57.07 119.99 185.76 257.24 343.03 986 42.40 89.13 137.98 191.08 254.81
1.18 44 196.08 7.72 52 231.73 9.123 1481 73.13 153.74 238.02 329.62 439.55 982 54.74 115.07 178.15 246.71 328.99
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.55
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)966 1190 1400 1610 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956
NUMBER OF BELT TEETH69 85 100 115 127 135 150 165 175 185 200 225 240 250 275 309 327 354
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)0.80 0.80 0.90 0.90 0.95 0.95 1.00 1.00 1.05 1.05 1.10 1.10 1.15 1.15 1.20 1.20 1.25 1.25
15.16 19.29 23.42 26.18 28.94 33.07 39.96 44.09 46.85 53.74 63.11 68.07 75.51
15.16 17.36 21.50 25.63 28.39 31.14 35.27 42.16 46.30 49.05 55.94 65.31 70.27 77.72
12.95 16.26 18.46 22.60 26.73 29.49 32.24 36.38 43.27 47.40 50.16 57.05 66.42 71.38 78.82
14.05 17.36 19.57 23.70 27.83 30.59 33.34 37.48 44.37 48.50 51.26 58.15 67.52 72.48 79.92
11.02 15.16 18.46 20.67 24.80 28.94 31.69 34.45 38.58 45.47 49.60 52.36 59.25 68.62 73.58 81.02
12.12 16.26 19.57 21.77 25.90 30.04 32.79 35.55 39.68 46.57 50.71 53.46 60.35 69.72 74.68 82.12
13.23 17.36 20.67 22.87 27.01 31.14 33.90 36.65 40.79 47.68 51.81 54.57 61.46 70.83 75.79 83.23
10.20 14.33 18.46 21.77 23.98 28.11 32.24 35.00 37.76 41.89 48.78 52.91 55.67 62.56 71.93 76.89 84.33
11.30 15.43 19.57 22.87 25.08 29.21 33.34 36.10 38.86 42.99 49.88 54.01 56.77 63.66 73.03 77.99 85.43
7.99 12.40 16.53 20.67 23.98 26.18 30.31 34.45 37.20 39.96 44.09 50.98 55.12 57.87 64.76 74.13 79.09 86.53
8.54 12.95 17.09 21.22 24.53 26.73 30.87 35.00 37.75 40.51 44.64 51.53 55.67 58.42 65.31 74.68 79.64 87.09
9.09 13.50 17.64 21.77 25.08 27.28 31.42 35.55 38.31 41.06 45.20 52.09 56.22 58.98 65.87 75.24 80.20 87.64
9.64 14.05 18.19 22.32 25.63 27.83 31.97 36.10 38.86 41.61 45.75 52.64 56.77 59.53 66.42 75.79 80.75 88.19
10.20 14.61 18.74 22.87 26.18 28.39 32.52 36.65 39.41 42.16 46.30 53.19 57.32 60.08 66.97 76.34 81.30 88.74
10.75 15.16 19.29 23.42 26.73 28.94 33.07 37.20 39.96 42.72 46.85 53.74 57.87 60.63 67.52 76.89 81.85 89.29
11.02 15.43 19.57 23.70 27.01 29.21 33.35 37.48 40.24 42.99 47.12 54.01 58.15 60.90 67.79 77.16 82.12 89.57
11.30 15.71 19.84 23.98 27.28 29.49 33.62 37.76 40.51 43.27 47.40 54.29 58.42 61.18 68.07 77.44 82.40 89.84
10.88 15.29 19.43 23.56 26.87 29.07 33.21 37.34 40.10 42.85 46.99 53.88 58.01 60.77 67.66 77.03 81.99 89.43
11.16 15.57 19.70 23.84 27.14 29.35 33.48 37.62 40.37 43.13 47.26 54.15 58.29 61.04 67.93 77.30 82.26 89.70
8.26 12.67 16.81 20.94 24.25 26.45 30.59 34.72 37.48 40.23 44.37 51.26 55.39 58.15 65.04 74.41 79.37 86.81
8.82 13.23 17.36 21.49 24.80 27.01 31.14 35.27 38.03 40.79 44.92 51.81 55.94 58.70 65.59 74.96 79.92 87.36
12.40 15.70 17.91 22.04 26.18 28.93 31.69 35.82 42.71 46.85 49.60 56.49 65.86 70.83 78.27
9.37 13.78 17.91 22.05 25.35 27.56 31.69 35.83 38.58 41.34 45.47 52.36 56.49 59.25 66.14 75.51 80.47 87.91
13.50 16.81 19.01 23.15 27.28 30.04 32.79 36.93 43.82 47.95 50.71 57.60 66.97 71.93 79.37
9.92 14.33 18.46 22.60 25.90 28.11 32.24 36.38 39.13 41.89 46.02 52.91 57.05 59.80 66.69 76.06 81.02 88.46
14.60 17.91 20.11 24.25 28.38 31.14 33.89 38.03 44.92 49.05 51.81 58.70 68.07 73.03 80.47
10.47 14.88 19.01 23.15 26.46 28.66 32.79 36.93 39.68 42.44 46.57 53.46 57.60 60.35 67.24 76.61 81.57 89.02
11.57 15.70 19.01 21.22 25.35 29.48 32.24 35.00 39.13 46.02 50.16 52.91 59.80 69.17 74.13 81.57
11.02 15.43 19.57 23.70 27.01 29.21 33.35 37.48 40.24 42.99 47.13 54.02 58.15 60.90 67.79 77.16 82.13 89.57
12.67 16.81 20.11 22.32 26.45 30.59 33.34 36.10 40.23 47.12 51.26 54.01 60.90 70.27 75.23 82.68
9.64 13.77 17.91 21.22 23.42 27.56 31.69 34.45 37.20 41.34 48.23 52.36 55.12 62.01 71.38 76.34 83.78
10.74 14.88 19.01 22.32 24.52 28.66 32.79 35.55 38.30 42.44 49.33 53.46 56.22 63.11 72.48 77.44 84.88
7.43 11.84 15.98 20.11 23.42 25.63 29.76 33.89 36.65 39.41 43.54 50.43 54.56 57.32 64.21 73.58 78.54 85.98
10.61 15.02 19.15 23.29 26.59 28.80 32.93 37.07 39.82 42.58 46.71 53.60 57.73 60.49 67.38 76.75 81.71 89.15
14.04 16.24 20.38 24.52 27.27 30.03 34.16 41.06 45.19 47.95 54.84 64.21 69.17 76.61
8.54 12.95 17.08 21.22 24.52 26.73 30.86 35.00 37.75 40.51 44.64 51.53 55.67 58.42 65.31 74.68 79.64 87.08
9.09 13.50 17.63 21.77 25.08 27.28 31.41 35.55 38.30 41.06 45.19 52.08 56.22 58.97 65.86 75.23 80.20 87.64
12.93 16.24 18.45 22.59 26.72 29.48 32.24 36.37 43.26 47.40 50.15 57.04 66.41 71.37 78.81
9.64 14.05 18.18 22.32 25.63 27.83 31.97 36.10 38.86 41.61 45.75 52.64 56.77 59.53 66.42 75.79 80.75 88.19
17.89 22.03 24.79 27.54 31.68 38.57 42.71 45.46 52.35 61.72 66.69 74.13
14.04 17.35 19.55 23.69 27.82 30.58 33.34 37.47 44.36 48.50 51.25 58.14 67.52 72.48 79.92
10.19 14.60 18.74 22.87 26.18 28.38 32.52 36.65 39.41 42.16 46.30 53.19 57.32 60.08 66.97 76.34 81.30 88.74
11.00 15.14 18.45 20.66 24.79 28.93 31.68 34.44 38.57 45.47 49.60 52.36 59.25 68.62 73.58 81.02
10.74 15.15 19.29 23.42 26.73 28.93 33.07 37.20 39.96 42.71 46.85 53.74 57.87 60.63 67.52 76.89 81.85 89.29
12.10 16.24 19.55 21.76 25.90 30.03 32.79 35.54 39.68 46.57 50.70 53.46 60.35 69.72 74.68 82.127.70 12.11 16.25 20.39 23.69 25.90 30.03 34.17 36.92 39.68 43.81 50.70 54.84 57.59 64.48 73.86 78.82 86.26
13.21 17.35 20.66 22.86 27.00 31.13 33.89 36.65 40.78 47.67 51.81 54.56 61.45 70.82 75.78 83.22
10.32 14.74 18.87 23.01 26.31 28.52 32.65 36.79 39.54 42.30 46.43 53.32 57.46 60.21 67.10 76.47 81.43 88.88
14.57 16.78 20.92 25.06 27.81 30.57 34.71 41.60 45.73 48.49 55.38 64.75 69.72 77.16
8.80 13.22 17.35 21.49 24.80 27.00 31.14 35.27 38.03 40.78 44.92 51.81 55.94 58.70 65.59 74.96 79.92 87.36
10.17 14.31 18.45 21.76 23.97 28.10 32.24 34.99 37.75 41.88 48.77 52.91 55.66 62.55 71.92 76.89 84.33
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
SPROCKET COMBINATIONS 1750 DRIVER RPM 1160 DRIVER RPMDRIVER DRIVEN HORSEPOWER RATING HORSEPOWER RATING
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm) DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 20 42 65 90 120 SPEED 20 42 65 90 120
56
1.19 32 142.6 5.614 38 169.34 6.667 1474 53.80 113.09 175.08 242.46 323.32 977 39.91 83.90 129.89 179.87 239.86
1.2 60 267.38 10.527 72 320.86 12.632 1458 97.36 204.69 316.90 438.86 585.21 967 74.10 155.77 241.16 333.97 445.34
1.2 40 178.25 7.018 48 213.9 8.421 1458 66.78 140.38 217.34 300.98 401.35 967 49.82 104.73 162.14 224.54 299.42
1.2 30 133.69 5.263 36 160.43 6.316 1458 50.50 106.16 164.36 227.61 303.52 967 37.42 78.67 121.79 168.66 224.90
1.21 56 249.55 9.825 68 303.03 11.93 1441 91.50 192.37 297.82 412.44 549.98 955 69.31 145.71 225.58 312.39 416.57
1.21 28 124.78 4.912 34 151.52 5.965 1441 47.19 99.20 153.58 212.69 283.61 955 34.93 73.43 113.67 157.42 209.92
1.22 36 160.43 6.316 44 196.08 7.72 1432 60.33 126.83 196.35 271.92 362.60 949 44.88 94.34 146.05 202.26 269.71
1.23 52 231.73 9.123 64 285.21 11.229 1422 85.51 179.76 278.29 385.40 513.93 943 64.49 135.57 209.88 290.66 387.59
1.24 29 129.23 5.088 36 160.43 6.316 1410 48.85 102.68 158.97 220.15 293.57 934 36.17 76.04 117.73 163.03 217.40
1.25 72 320.86 12.632 90 401.07 15.79 1400 114.00 239.67 371.06 513.87 685.24 928 88.19 185.40 287.03 397.50 530.06
1.25 64 285.21 11.229 80 356.51 14.036 1400 103.07 216.70 335.49 464.61 619.55 928 78.84 165.75 256.60 355.36 473.87
1.25 48 213.9 8.421 60 267.38 10.527 1400 79.38 166.87 258.34 357.77 477.08 928 59.63 125.35 194.07 268.75 358.38
1.25 32 142.6 5.614 40 178.25 7.018 1400 53.80 113.09 175.08 242.46 323.32 928 39.91 83.90 129.89 179.87 239.86
1.26 38 169.34 6.667 48 213.9 8.421 1385 63.57 133.63 206.88 286.50 382.05 918 47.35 99.54 154.10 213.41 284.58
1.27 30 133.69 5.263 38 169.34 6.667 1382 50.50 106.16 164.36 227.61 303.52 916 37.42 78.67 121.79 168.66 224.90
1.27 44 196.08 7.72 56 249.55 9.825 1375 73.13 153.74 238.02 329.62 439.55 911 54.74 115.07 178.15 246.71 328.99
1.29 56 249.55 9.825 72 320.86 12.632 1361 91.50 192.37 297.82 412.44 549.98 902 69.31 145.71 225.58 312.39 416.57
1.29 28 124.78 4.912 36 160.43 6.316 1361 47.19 99.20 153.58 212.69 283.61 902 34.93 73.43 113.67 157.42 209.92
1.29 34 151.52 5.965 44 196.08 7.72 1352 57.07 119.99 185.76 257.24 343.03 896 42.40 89.13 137.98 191.08 254.81
1.30 40 178.25 7.018 52 231.73 9.123 1346 66.78 140.38 217.34 300.98 401.35 892 49.82 104.73 162.14 224.54 299.42
1.31 52 231.73 9.123 68 303.03 11.93 1338 85.51 179.76 278.29 385.40 513.93 887 64.49 135.57 209.88 290.66 387.59
1.31 29 129.23 5.088 38 169.34 6.667 1336 48.85 102.68 158.97 220.15 293.57 885 36.17 76.04 117.73 163.03 217.40
1.32 68 303.03 11.93 90 401.07 15.79 1322 108.62 228.36 353.55 489.62 652.90 876 83.54 175.62 271.89 376.53 502.10
1.33 60 267.38 10.527 80 356.51 14.036 1313 97.36 204.69 316.90 438.86 585.21 870 74.10 155.77 241.16 333.97 445.34
1.33 48 213.9 8.421 64 285.21 11.229 1313 79.38 166.87 258.34 357.77 477.08 870 59.63 125.35 194.07 268.75 358.38
1.33 36 160.43 6.316 48 213.9 8.421 1313 60.33 126.83 196.35 271.92 362.60 870 44.88 94.34 146.05 202.26 269.71
1.33 30 133.69 5.263 40 178.25 7.018 1313 50.50 106.16 164.36 227.61 303.52 870 37.42 78.67 121.79 168.66 224.90
1.36 28 124.78 4.912 38 169.34 6.667 1289 47.19 99.20 153.58 212.69 283.61 855 34.93 73.43 113.67 157.42 209.92
1.36 44 196.08 7.72 60 267.38 10.527 1283 73.13 153.74 238.02 329.62 439.55 851 54.74 115.07 178.15 246.71 328.99
1.37 38 169.34 6.667 52 231.73 9.123 1279 63.57 133.63 206.88 286.50 382.05 848 47.35 99.54 154.10 213.41 284.58
1.38 32 142.6 5.614 44 196.08 7.72 1273 53.80 113.09 175.08 242.46 323.32 844 39.91 83.90 129.89 179.87 239.86
1.38 29 129.23 5.088 40 178.25 7.018 1269 48.85 102.68 158.97 220.15 293.57 841 36.17 76.04 117.73 163.03 217.40
1.38 52 231.73 9.123 72 320.86 12.632 1264 85.51 179.76 278.29 385.40 513.93 838 64.49 135.57 209.88 290.66 387.59
1.40 80 356.51 14.036 112 499.11 19.65 1250 124.20 261.12 404.27 559.86 746.57 829 97.34 204.63 316.80 438.72 585.03
1.40 40 178.25 7.018 56 249.55 9.825 1250 66.78 140.38 217.34 300.98 401.35 829 49.82 104.73 162.14 224.54 299.42
1.41 64 285.21 11.229 90 401.07 15.79 1244 103.07 216.70 335.49 464.61 619.55 825 78.84 165.75 256.60 355.36 473.87
1.41 34 151.52 5.965 48 213.9 8.421 1240 57.07 119.99 185.76 257.24 343.03 822 42.40 89.13 137.98 191.08 254.81
1.42 48 213.9 8.421 68 303.03 11.93 1235 79.38 166.87 258.34 357.77 477.08 819 59.63 125.35 194.07 268.75 358.38
1.43 56 249.55 9.825 80 356.51 14.036 1225 91.50 192.37 297.82 412.44 549.98 812 69.31 145.71 225.58 312.39 416.57
1.43 28 124.78 4.912 40 178.25 7.018 1225 47.19 99.20 153.58 212.69 283.61 812 34.93 73.43 113.67 157.42 209.92
1.44 36 160.43 6.316 52 231.73 9.123 1212 60.33 126.83 196.35 271.92 362.60 803 44.88 94.34 146.05 202.26 269.71
1.45 44 196.08 7.72 64 285.21 11.229 1203 73.13 153.74 238.02 329.62 439.55 798 54.74 115.07 178.15 246.71 328.99
1.47 30 133.69 5.263 44 196.08 7.72 1193 50.50 106.16 164.36 227.61 303.52 791 37.42 78.67 121.79 168.66 224.90
1.47 38 169.34 6.667 56 249.55 9.825 1188 63.57 133.63 206.88 286.50 382.05 787 47.35 99.54 154.10 213.41 284.58
1.50 60 267.38 10.527 90 401.07 15.79 1167 97.36 204.69 316.90 438.86 585.21 773 74.10 155.77 241.16 333.97 445.34
1.50 48 213.9 8.421 72 320.86 12.632 1167 79.38 166.87 258.34 357.77 477.08 773 59.63 125.35 194.07 268.75 358.38
1.50 40 178.25 7.018 60 267.38 10.527 1167 66.78 140.38 217.34 300.98 401.35 773 49.82 104.73 162.14 224.54 299.42
1.50 32 142.6 5.614 48 213.9 8.421 1167 53.80 113.09 175.08 242.46 323.32 773 39.91 83.90 129.89 179.87 239.86
1.52 29 129.23 5.088 44 196.08 7.72 1153 48.85 102.68 158.97 220.15 293.57 765 36.17 76.04 117.73 163.03 217.40
1.53 34 151.52 5.965 52 231.73 9.123 1144 57.07 119.99 185.76 257.24 343.03 758 42.40 89.13 137.98 191.08 254.81
1.54 52 231.73 9.123 80 356.51 14.036 1138 85.51 179.76 278.29 385.40 513.93 754 64.49 135.57 209.88 290.66 387.59
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.57
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)966 1190 1400 1610 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956
NUMBER OF BELT TEETH69 85 100 115 127 135 150 165 175 185 200 225 240 250 275 309 327 354
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)0.80 0.80 0.90 0.90 0.95 0.95 1.00 1.00 1.05 1.05 1.10 1.10 1.15 1.15 1.20 1.20 1.25 1.25
9.35 13.77 17.90 22.04 25.35 27.55 31.69 35.82 38.58 41.33 45.47 52.36 56.49 59.25 66.14 75.51 80.47 87.91
13.46 16.78 18.99 23.12 27.26 30.02 32.78 36.91 43.81 47.94 50.70 57.59 66.96 71.92 79.36
11.28 15.42 19.55 22.86 25.07 29.20 33.34 36.09 38.85 42.99 49.88 54.01 56.77 63.66 73.03 77.99 85.43
9.91 14.32 18.46 22.59 25.90 28.10 32.24 36.37 39.13 41.89 46.02 52.91 57.04 59.80 66.69 76.06 81.02 88.46
14.57 17.88 20.09 24.23 28.37 31.12 33.88 38.02 44.91 49.04 51.80 58.69 68.06 73.02 80.46
10.46 14.87 19.01 23.14 26.45 28.66 32.79 36.92 39.68 42.44 46.57 53.46 57.60 60.35 67.24 76.61 81.57 89.01
7.96 12.38 16.52 20.66 23.96 26.17 30.31 34.44 37.20 39.95 44.09 50.98 55.11 57.87 64.76 74.13 79.09 86.53
11.53 15.67 18.99 21.19 25.33 29.47 32.23 34.98 39.12 46.01 50.15 52.90 59.79 69.16 74.13 81.57
10.04 14.45 18.59 22.73 26.04 28.24 32.38 36.51 39.27 42.02 46.16 53.05 57.18 59.94 66.83 76.20 81.16 88.60
14.80 18.95 23.09 25.86 28.62 32.76 39.65 43.79 46.55 53.44 62.81 67.78 75.22
15.09 17.30 21.45 25.59 28.35 31.11 35.25 42.14 46.28 49.03 55.93 65.30 70.26 77.70
12.63 16.78 20.09 22.30 26.43 30.57 33.33 36.09 40.22 47.11 51.25 54.00 60.90 70.27 75.23 82.67
9.07 13.48 17.62 21.76 25.07 27.27 31.41 35.54 38.30 41.06 45.19 52.08 56.22 58.97 65.86 75.23 80.19 87.63
11.54 15.68 19.82 23.13 25.34 29.47 33.61 36.37 39.12 43.26 50.15 54.28 57.04 63.93 73.30 78.26 85.70
9.62 14.04 18.17 22.31 25.62 27.83 31.96 36.09 38.85 41.61 45.74 52.63 56.77 59.52 66.41 75.78 80.74 88.19
9.59 13.74 17.88 21.19 23.40 27.54 31.67 34.43 37.19 41.32 48.22 52.35 55.11 62.00 71.37 76.33 83.77
13.98 17.30 19.52 23.66 27.80 30.56 33.32 37.45 44.35 48.48 51.24 58.13 67.50 72.47 79.91
10.17 14.59 18.73 22.86 26.17 28.38 32.51 36.65 39.40 42.16 46.29 53.18 57.32 60.07 66.96 76.33 81.30 88.74
8.22 12.65 16.79 20.93 24.23 26.44 30.58 34.71 37.47 40.23 44.36 51.25 55.39 58.14 65.03 74.40 79.36 86.81
10.70 14.84 18.99 22.30 24.50 28.64 32.78 35.53 38.29 42.43 49.32 53.45 56.21 63.10 72.47 77.43 84.87
10.93 15.09 18.41 20.62 24.76 28.90 31.66 34.42 38.56 45.45 49.59 52.34 59.23 68.61 73.57 81.01
9.75 14.17 18.31 22.45 25.75 27.96 32.10 36.23 38.99 41.74 45.88 52.77 56.90 59.66 66.55 75.92 80.88 88.32
15.31 19.47 23.62 26.39 29.15 33.29 40.19 44.33 47.09 53.98 63.36 68.32 75.76
15.61 17.83 21.98 26.12 28.88 31.64 35.78 42.68 46.82 49.57 56.47 65.84 70.80 78.25
12.04 16.20 19.52 21.73 25.87 30.01 32.76 35.52 39.66 46.55 50.69 53.45 60.34 69.71 74.67 82.11
11.80 15.95 20.09 23.40 25.61 29.74 33.88 36.64 39.39 43.53 50.42 54.56 57.31 64.20 73.57 78.54 85.98
9.33 13.75 17.89 22.03 25.34 27.54 31.68 35.82 38.57 41.33 45.46 52.35 56.49 59.24 66.14 75.51 80.47 87.91
9.88 14.30 18.44 22.58 25.89 28.10 32.23 36.37 39.12 41.88 46.01 52.91 57.04 59.80 66.69 76.06 81.02 88.46
13.15 17.30 20.62 22.83 26.97 31.11 33.87 36.63 40.76 47.66 51.79 54.55 61.44 70.81 75.77 83.22
10.95 15.11 19.25 22.56 24.77 28.91 33.05 35.80 38.56 42.70 49.59 53.73 56.48 63.37 72.74 77.71 85.15
8.48 12.91 17.05 21.19 24.50 26.71 30.85 34.98 37.74 40.50 44.63 51.52 55.66 58.41 65.31 74.68 79.64 87.08
9.46 13.88 18.02 22.16 25.47 27.68 31.81 35.95 38.71 41.46 45.60 52.49 56.62 59.38 66.27 75.64 80.60 88.04
14.50 17.83 20.04 24.19 28.33 31.09 33.85 37.99 44.89 49.02 51.78 58.67 68.05 73.01 80.45
18.81 21.59 24.36 28.52 35.44 39.58 42.35 49.25 58.63 63.60 71.05
10.10 14.26 18.41 21.73 23.93 28.07 32.21 34.97 37.73 41.87 48.76 52.89 55.65 62.54 71.91 76.88 84.32
13.59 15.82 19.99 24.14 26.91 29.67 33.82 40.72 44.86 47.62 54.52 63.90 68.86 76.30
7.62 12.06 16.21 20.36 23.67 25.88 30.01 34.15 36.91 39.67 43.80 50.69 54.83 57.58 64.48 73.85 78.81 86.25
11.44 15.61 18.93 21.15 25.29 29.44 32.20 34.96 39.09 45.99 50.13 52.88 59.78 69.15 74.11 81.56
12.78 16.12 18.34 22.50 26.65 29.41 32.17 36.32 43.22 47.35 50.11 57.01 66.38 71.35 78.79
9.59 14.01 18.16 22.30 25.61 27.81 31.95 36.09 38.84 41.60 45.74 52.63 56.76 59.52 66.41 75.78 80.74 88.18
11.21 15.37 19.52 22.83 25.04 29.18 33.32 36.07 38.83 42.97 49.86 54.00 56.75 63.65 73.02 77.98 85.42
12.55 16.72 20.04 22.25 26.40 30.54 33.30 36.06 40.20 47.09 51.23 53.99 60.88 70.25 75.21 82.66
8.73 13.17 17.32 21.46 24.77 26.98 31.12 35.25 38.01 40.77 44.90 51.80 55.93 58.69 65.58 74.95 79.91 87.35
10.35 14.52 18.67 21.99 24.20 28.34 32.48 35.24 38.00 42.13 49.03 53.16 55.92 62.81 72.19 77.15 84.59
14.08 16.32 20.50 24.66 27.43 30.20 34.35 41.25 45.40 48.16 55.05 64.43 69.40 76.84
10.82 15.01 18.34 20.56 24.71 28.86 31.62 34.38 38.52 45.42 49.56 52.32 59.21 68.59 73.55 81.00
9.48 13.67 17.83 21.15 23.36 27.50 31.64 34.40 37.16 41.30 48.20 52.33 55.09 61.98 71.36 76.32 83.76
7.87 12.32 16.48 20.62 23.93 26.14 30.28 34.42 37.18 39.94 44.07 50.96 55.10 57.86 64.75 74.12 79.08 86.52
8.86 13.30 17.45 21.59 24.90 27.11 31.25 35.39 38.15 40.90 45.04 51.93 56.07 58.82 65.71 75.09 80.05 87.49
11.47 15.63 19.78 23.09 25.30 29.45 33.58 36.34 39.10 43.24 50.13 54.27 57.02 63.92 73.29 78.25 85.69
13.27 16.63 18.85 23.02 27.17 29.94 32.70 36.85 43.75 47.89 50.65 57.54 66.92 71.89 79.33
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
SPROCKET COMBINATIONS 1750 DRIVER RPM 1160 DRIVER RPMDRIVER DRIVEN HORSEPOWER RATING HORSEPOWER RATING
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm) DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 20 42 65 90 120 SPEED 20 42 65 90 120
58
1.55 44 196.08 7.72 68 303.03 11.93 1132 73.13 153.74 238.02 329.62 439.55 751 54.74 115.07 178.15 246.71 328.99
1.56 72 320.86 12.632 112 499.11 19.65 1125 114.00 239.67 371.06 513.87 685.24 746 88.19 185.40 287.03 397.50 530.06
1.56 36 160.43 6.316 56 249.55 9.825 1125 60.33 126.83 196.35 271.92 362.60 746 44.88 94.34 146.05 202.26 269.711.57 28 124.78 4.912 44 196.08 7.72 1114 47.19 99.20 153.58 212.69 283.61 738 34.93 73.43 113.67 157.42 209.92
1.58 38 169.34 6.667 60 267.38 10.527 1108 63.57 133.63 206.88 286.50 382.05 735 47.35 99.54 154.10 213.41 284.58
1.60 40 178.25 7.018 64 285.21 11.229 1094 66.78 140.38 217.34 300.98 401.35 725 49.82 104.73 162.14 224.54 299.42
1.60 30 133.69 5.263 48 213.9 8.421 1094 50.50 106.16 164.36 227.61 303.52 725 37.42 78.67 121.79 168.66 224.90
1.61 56 249.55 9.825 90 401.07 15.79 1089 91.50 192.37 297.82 412.44 549.98 722 69.31 145.71 225.58 312.39 416.57
1.63 32 142.6 5.614 52 231.73 9.123 1077 53.80 113.09 175.08 242.46 323.32 714 39.91 83.90 129.89 179.87 239.86
1.64 44 196.08 7.72 72 320.86 12.632 1069 73.13 153.74 238.02 329.62 439.55 709 54.74 115.07 178.15 246.71 328.99
1.65 68 303.03 11.93 112 499.11 19.65 1063 108.62 228.36 353.55 489.62 652.90 704 83.54 175.62 271.89 376.53 502.10
1.65 34 151.52 5.965 56 249.55 9.825 1063 57.07 119.99 185.76 257.24 343.03 704 42.40 89.13 137.98 191.08 254.81
1.66 29 129.23 5.088 48 213.9 8.421 1057 48.85 102.68 158.97 220.15 293.57 701 36.17 76.04 117.73 163.03 217.40
1.67 48 213.9 8.421 80 356.51 14.036 1050 79.38 166.87 258.34 357.77 477.08 696 59.63 125.35 194.07 268.75 358.38
1.67 36 160.43 6.316 60 267.38 10.527 1050 60.33 126.83 196.35 271.92 362.60 696 44.88 94.34 146.05 202.26 269.71
1.68 38 169.34 6.667 64 285.21 11.229 1039 63.57 133.63 206.88 286.50 382.05 689 47.35 99.54 154.10 213.41 284.58
1.70 40 178.25 7.018 68 303.03 11.93 1029 66.78 140.38 217.34 300.98 401.35 682 49.82 104.73 162.14 224.54 299.421.71 28 124.78 4.912 48 213.9 8.421 1021 47.19 99.20 153.58 212.69 283.61 677 34.93 73.43 113.67 157.42 209.92
1.73 52 231.73 9.123 90 401.07 15.79 1011 85.51 179.76 278.29 385.40 513.93 670 64.49 135.57 209.88 290.66 387.59
1.73 30 133.69 5.263 52 231.73 9.123 1010 50.50 106.16 164.36 227.61 303.52 669 37.42 78.67 121.79 168.66 224.90
1.75 64 285.21 11.229 112 499.11 19.65 1000 103.07 216.70 335.49 464.61 619.55 663 78.84 165.75 256.60 355.36 473.87
1.75 32 142.6 5.614 56 249.55 9.825 1000 53.80 113.09 175.08 242.46 323.32 663 39.91 83.90 129.89 179.87 239.86
1.76 34 151.52 5.965 60 267.38 10.527 992 57.07 119.99 185.76 257.24 343.03 657 42.40 89.13 137.98 191.08 254.81
1.78 36 160.43 6.316 64 285.21 11.229 984 60.33 126.83 196.35 271.92 362.60 653 44.88 94.34 146.05 202.26 269.71
1.79 38 169.34 6.667 68 303.03 11.93 978 63.57 133.63 206.88 286.50 382.05 648 47.35 99.54 154.10 213.41 284.58
1,79 29 129.23 5.088 52 231.73 9.123 976 48.85 102.68 158.97 220.15 293.57 647 36.17 76.04 117.73 163.03 217.40
1.80 80 356.51 14.036 144 641.71 25.264 972 124.20 261.12 404.27 559.86 746.57 644 97.34 204.63 316.80 438.72 585.03
1.80 40 178.25 7.018 72 320.86 12.632 972 66.78 140.38 217.34 300.98 401.35 644 49.82 104.73 162.14 224.54 299.42
1.82 44 196.08 7.72 80 356.51 14.036 963 73.13 153.74 238.02 329.62 439.55 638 54.74 115.07 178.15 246.71 328.99
1.86 28 124.78 4.912 52 231.73 9.123 942 47.19 99.20 153.58 212.69 283.61 625 34.93 73.43 113.67 157.42 209.92
1.87 60 267.38 10.527 112 499.11 19.65 938 97.36 204.69 316.90 438.86 585.21 621 74.10 155.77 241.16 333.97 445.34
1.87 30 133.69 5.263 56 249.55 9.825 938 50.50 106.16 164.36 227.61 303.52 621 37.42 78.67 121.79 168.66 224.90
1.88 48 213.9 8.421 90 401.07 15.79 933 79.38 166.87 258.34 357.77 477.08 619 59.63 125.35 194.07 268.75 358.381.88 32 142.6 5.614 60 267.38 10.527 933 53.80 113.09 175.08 242.46 323.32 619 39.91 83.90 129.89 179.87 239.86
1.88 34 151.52 5.965 64 285.21 11.229 930 57.07 119.99 185.76 257.24 343.03 616 42.40 89.13 137.98 191.08 254.81
1.89 36 160.43 6.316 68 303.03 11.93 926 60.33 126.83 196.35 271.92 362.60 614 44.88 94.34 146.05 202.26 269.71
1.89 38 169.34 6.667 72 320.86 12.632 924 63.57 133.63 206.88 286.50 382.05 612 47.35 99.54 154.10 213.41 284.58
1.93 29 129.23 5.088 56 249.55 9.825 906 48.85 102.68 158.97 220.15 293.57 601 36.17 76.04 117.73 163.03 217.40
2 72 320.86 12.632 144 641.71 25.264 875 114.00 239.67 371.06 513.87 685.24 580 88.19 185.40 287.03 397.50 530.06
2 56 249.55 9.825 112 499.11 19.65 875 91.50 192.37 297.82 412.44 549.98 580 69.31 145.71 225.58 312.39 416.57
2 40 178.25 7.018 80 356.51 14.036 875 66.78 140.38 217.34 300.98 401.35 580 49.82 104.73 162.14 224.54 299.42
2 36 160.43 6.316 72 320.86 12.632 875 60.33 126.83 196.35 271.92 362.60 580 44.88 94.34 146.05 202.26 269.71
2 34 151.52 5.965 68 303.03 11.93 875 57.07 119.99 185.76 257.24 343.03 580 42.40 89.13 137.98 191.08 254.81
2 32 142.6 5.614 64 285.21 11.229 875 53.80 113.09 175.08 242.46 323.32 580 39.91 83.90 129.89 179.87 239.86
2 30 133.69 5.263 60 267.38 10.527 875 50.50 106.16 164.36 227.61 303.52 580 37.42 78.67 121.79 168.66 224.902 28 124.78 4.912 56 249.55 9.825 875 47.19 99.20 153.58 212.69 283.61 580 34.93 73.43 113.67 157.42 209.92
2.05 44 196.08 7.72 90 401.07 15.79 856 73.13 153.74 238.02 329.62 439.55 567 54.74 115.07 178.15 246.71 328.99
2.07 29 129.23 5.088 60 267.38 10.527 846 48.85 102.68 158.97 220.15 293.57 561 36.17 76.04 117.73 163.03 217.40
2.1 80 356.51 14.036 168 748.66 29.475 833 124.20 261.12 404.27 559.86 746.57 552 97.34 204.63 316.80 438.72 585.03
2.11 38 169.34 6.667 80 356.51 14.036 831 63.57 133.63 206.88 286.50 382.05 551 47.35 99.54 154.10 213.41 284.58
2.12 68 303.03 11.93 144 641.71 25.264 826 108.62 228.36 353.55 489.62 652.90 548 83.54 175.62 271.89 376.53 502.10
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.59
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)966 1190 1400 1610 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956
NUMBER OF BELT TEETH69 85 100 115 127 135 150 165 175 185 200 225 240 250 275 309 327 354
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)0.80 0.80 0.90 0.90 0.95 0.95 1.00 1.00 1.05 1.05 1.10 1.10 1.15 1.15 1.20 1.20 1.25 1.25
11.94 16.12 19.45 21.67 25.82 29.96 32.73 35.49 39.63 46.53 50.66 53.42 60.32 69.69 74.65 82.10
19.81 22.60 25.39 29.55 36.48 40.64 43.40 50.31 59.70 64.67 72.12
10.60 14.78 18.93 22.25 24.46 28.61 32.75 35.51 38.27 42.40 49.30 53.43 56.19 63.08 72.46 77.42 84.868.98 13.43 17.58 21.73 25.04 27.25 31.39 35.52 38.28 41.04 45.17 52.07 56.20 58.96 65.85 75.22 80.18 87.63
9.73 13.92 18.08 21.41 23.62 27.77 31.91 34.67 37.43 41.57 48.46 52.60 55.36 62.25 71.63 76.59 84.03
13.06 17.23 20.56 22.78 26.92 31.07 33.83 36.59 40.73 47.63 51.77 54.52 61.42 70.79 75.76 83.20
8.11 12.58 16.74 20.88 24.20 26.41 30.55 34.69 37.45 40.20 44.34 51.24 55.37 58.13 65.02 74.39 79.35 86.80
14.57 16.82 21.01 25.18 27.95 30.72 34.87 41.78 45.93 48.69 55.59 64.97 69.94 77.38
11.72 15.89 20.04 23.36 25.57 29.71 33.85 36.61 39.37 43.51 50.40 54.54 57.30 64.19 73.56 78.52 85.97
11.31 15.51 18.85 21.08 25.23 29.38 32.15 34.91 39.06 45.96 50.10 52.86 59.75 69.13 74.09 81.54
16.07 20.30 23.10 25.89 30.07 37.00 41.16 43.92 50.84 60.23 65.20 72.65
10.85 15.03 19.19 22.51 24.73 28.87 33.01 35.77 38.53 42.67 49.57 53.70 56.46 63.36 72.73 77.69 85.13
8.24 12.70 16.87 21.02 24.33 26.54 30.68 34.82 37.58 40.34 44.48 51.37 55.51 58.26 65.16 74.53 79.49 86.93
13.77 17.13 19.36 23.53 27.69 30.46 33.23 37.37 44.28 48.42 51.18 58.08 67.46 72.43 79.87
9.97 14.17 18.34 21.67 23.88 28.03 32.17 34.94 37.70 41.84 48.73 52.87 55.63 62.52 71.90 76.86 84.30
9.08 13.31 17.49 20.82 23.04 27.19 31.33 34.10 36.86 41.00 47.90 52.04 54.79 61.69 71.06 76.03 83.47
12.43 16.63 19.97 22.19 26.34 30.49 33.25 36.02 40.16 47.06 51.20 53.96 60.86 70.23 75.20 82.648.36 12.83 17.00 21.15 24.46 26.67 30.82 34.96 37.71 40.47 44.61 51.51 55.64 58.40 65.29 74.66 79.63 87.07
15.06 17.32 21.51 25.69 28.47 31.24 35.39 42.31 46.45 49.22 56.12 65.51 70.47 77.92
7.47 11.97 16.14 20.30 23.62 25.83 29.98 34.12 36.88 39.64 43.78 50.67 54.81 57.57 64.46 73.83 78.79 86.24
16.55 20.79 23.60 26.39 30.57 37.52 41.68 44.44 51.36 60.76 65.73 73.18
11.10 15.29 19.45 22.78 24.99 29.14 33.28 36.04 38.80 42.94 49.84 53.97 56.73 63.63 73.00 77.96 85.41
10.22 14.42 18.60 21.93 24.14 28.29 32.44 35.20 37.96 42.10 49.00 53.14 55.90 62.79 72.17 77.13 84.57
9.32 13.55 17.74 21.08 23.29 27.45 31.60 34.36 37.12 41.26 48.16 52.30 55.06 61.96 71.33 76.30 83.74
12.68 16.88 20.22 22.44 26.60 30.75 33.52 36.28 40.43 47.33 51.47 54.23 61.12 70.50 75.47 82.91
7.58 12.09 16.27 20.43 23.75 25.96 30.11 34.25 37.01 39.77 43.91 50.81 54.94 57.70 64.59 73.97 78.93 86.37
23.58 30.63 34.82 37.61 44.57 54.00 58.98 66.45
11.79 16.01 19.36 21.59 25.75 29.91 32.67 35.44 39.58 46.49 50.63 53.39 60.29 69.67 74.63 82.08
14.25 17.63 19.86 24.04 28.21 30.98 33.75 37.90 44.81 48.95 51.71 58.61 68.00 72.96 80.41
7.70 12.22 16.40 20.56 23.88 26.10 30.24 34.38 37.14 39.90 44.04 50.94 55.08 57.84 64.73 74.10 79.07 86.51
17.02 21.28 24.09 26.89 31.08 38.03 42.19 44.96 51.88 61.29 66.26 73.72
11.34 15.54 19.71 23.04 25.25 29.40 33.54 36.31 39.07 43.21 50.10 54.24 57.00 63.90 73.27 78.23 85.68
12.11 15.55 17.81 22.01 26.20 28.98 31.75 35.91 42.83 46.98 49.74 56.65 66.04 71.01 78.4610.46 14.68 18.85 22.19 24.40 28.55 32.70 35.47 38.23 42.37 49.27 53.41 56.17 63.06 72.44 77.40 84.85
9.56 13.80 18.00 21.33 23.55 27.71 31.86 34.62 37.39 41.53 48.43 52.57 55.33 62.23 71.60 76.57 84.01
12.92 17.13 20.48 22.70 26.86 31.01 33.78 36.55 40.69 47.59 51.73 54.49 61.39 70.77 75.73 83.18
12.03 16.26 19.61 21.84 26.01 30.17 32.93 35.70 39.85 46.75 50.90 53.66 60.56 69.94 74.90 82.35
11.47 15.67 19.84 23.17 25.38 29.53 33.68 36.44 39.20 43.34 50.24 54.38 57.13 64.03 73.41 78.37 85.81
20.23 24.54 31.61 35.82 38.62 45.58 55.03 60.02 67.50
17.49 21.77 24.59 27.39 31.58 38.54 42.71 45.48 52.41 61.81 66.79 74.25
14.74 18.12 20.36 24.55 28.72 31.50 34.27 38.42 45.34 49.48 52.24 59.15 68.53 73.50 80.95
12.27 16.51 19.87 22.10 26.27 30.43 33.20 35.96 40.11 47.02 51.16 53.92 60.82 70.20 75.17 82.62
13.16 17.38 20.73 22.96 27.12 31.27 34.04 36.81 40.95 47.86 52.00 54.76 61.66 71.04 76.00 83.45
9.79 14.05 18.25 21.59 23.81 27.97 32.12 34.89 37.65 41.79 48.70 52.84 55.60 62.49 71.87 76.84 84.28
10.70 14.92 19.11 22.44 24.66 28.82 32.96 35.73 38.49 42.63 49.54 53.67 56.43 63.33 72.71 77.67 85.1211.59 15.79 19.97 23.30 25.51 29.66 33.81 36.57 39.33 43.47 50.37 54.51 57.27 64.16 73.54 78.50 85.95
12.57 16.02 18.29 22.51 26.70 29.49 32.27 36.43 43.35 47.50 50.27 57.18 66.57 71.54 78.99
10.82 15.05 19.24 22.57 24.79 28.95 33.10 35.86 38.62 42.77 49.67 53.81 56.57 63.46 72.84 77.81 85.25
26.71 31.00 33.84 40.88 50.39 55.40 62.91
10.65 14.98 18.37 20.61 24.80 28.98 31.75 34.53 38.68 45.60 49.74 52.51 59.41 68.80 73.77 81.21
20.69 25.01 32.10 36.31 39.12 46.09 55.54 60.54 68.02
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
SPROCKET COMBINATIONS 1750 DRIVER RPM 1160 DRIVER RPMDRIVER DRIVEN HORSEPOWER RATING HORSEPOWER RATING
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm) DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 20 42 65 90 120 SPEED 20 42 65 90 120
60
2.12 34 151.52 5.965 72 320.86 12.632 826 57.07 119.99 185.76 257.24 343.03 548 42.40 89.13 137.98 191.08 254.81
2.13 32 142.6 5.614 68 303.03 11.93 824 53.80 113.09 175.08 242.46 323.32 546 39.91 83.90 129.89 179.87 239.86
2.13 30 133.69 5.263 64 285.21 11.229 820 50.50 106.16 164.36 227.61 303.52 544 37.42 78.67 121.79 168.66 224.90
2.14 28 124.78 4.912 60 267.38 10.527 817 47.19 99.20 153.58 212.69 283.61 541 34.93 73.43 113.67 157.42 209.92
2.15 52 231.73 9.123 112 499.11 19.65 813 85.51 179.76 278.29 385.40 513.93 539 64.49 135.57 209.88 290.66 387.59
2.21 29 129.23 5.088 64 285.21 11.229 793 48.85 102.68 158.97 220.15 293.57 526 36.17 76.04 117.73 163.03 217.40
2.22 36 160.43 6.316 80 356.51 14.036 788 60.33 126.83 196.35 271.92 362.60 522 44.88 94.34 146.05 202.26 269.71
2.25 64 285.21 11.229 144 641.71 25.264 778 103.07 216.70 335.49 464.61 619.55 516 78.84 165.75 256.60 355.36 473.87
2.25 40 178.25 7.018 90 401.07 15.79 778 66.78 140.38 217.34 300.98 401.35 516 49.82 104.73 162.14 224.54 299.42
2.25 32 142.6 5.614 72 320.86 12.632 778 53.80 113.09 175.08 242.46 323.32 516 39.91 83.90 129.89 179.87 239.86
2.27 30 133.69 5.263 68 303.03 11.93 772 50.50 106.16 164.36 227.61 303.52 512 37.42 78.67 121.79 168.66 224.90
2.29 28 124.78 4.912 64 285.21 11.229 766 47.19 99.20 153.58 212.69 283.61 508 34.93 73.43 113.67 157.42 209.92
2.33 72 320.86 12.632 168 748.66 29.475 750 114.00 239.67 371.06 513.87 685.24 497 88.19 185.40 287.03 397.50 530.06
2.33 48 213.9 8.421 112 499.11 19.65 750 79.38 166.87 258.34 357.77 477.08 497 59.63 125.35 194.07 268.75 358.38
2.34 29 129.23 5.088 68 303.03 11.93 746 48.85 102.68 158.97 220.15 293.57 495 36.17 76.04 117.73 163.03 217.40
2.35 34 151.52 5.965 80 356.51 14.036 744 57.07 119.99 185.76 257.24 343.03 493 42.40 89.13 137.98 191.08 254.81
2.37 38 169.34 6.667 90 401.07 15.79 739 63.57 133.63 206.88 286.50 382.05 490 47.35 99.54 154.10 213.41 284.58
2.4 80 356.51 14.036 192 855.62 33.686 729 124.20 261.12 404.27 559.86 746.57 483 97.34 204.63 316.80 438.72 585.03
2.4 60 267.38 10.527 144 641.71 25.264 729 97.36 204.69 316.90 438.86 585.21 483 74.10 155.77 241.16 333.97 445.34
2.4 30 133.69 5.263 72 320.86 12.632 729 50.50 106.16 164.36 227.61 303.52 483 37.42 78.67 121.79 168.66 224.90
2.43 28 124.78 4.912 68 303.03 11.93 721 47.19 99.20 153.58 212.69 283.61 478 34.93 73.43 113.67 157.42 209.92
2.47 68 303.03 11.93 168 748.66 29.475 708 108.62 228.36 353.55 489.62 652.90 470 83.54 175.62 271.89 376.53 502.10
2.48 29 129.23 5.088 72 320.86 12.632 705 48.85 102.68 158.97 220.15 293.57 467 36.17 76.04 117.73 163.03 217.402.50 36 160.43 6.316 90 401.07 15.79 700 60.33 126.83 196.35 271.92 362.60 464 44.88 94.34 146.05 202.26 269.71
2.50 32 142.6 5.614 80 356.51 14.036 700 53.80 113.09 175.08 242.46 323.32 464 39.91 83.90 129.89 179.87 239.86
2.55 44 196.08 7.72 112 499.11 19.65 688 73.13 153.74 238.02 329.62 439.55 456 54.74 115.07 178.15 246.71 328.99
2.57 56 249.55 9.825 144 641.71 25.264 681 91.50 192.37 297.82 412.44 549.98 451 69.31 145.71 225.58 312.39 416.57
2.57 28 124.78 4.912 72 320.86 12.632 681 47.19 99.20 153.58 212.69 283.61 451 34.93 73.43 113.67 157.42 209.92
2.63 64 285.21 11.229 168 748.66 29.475 667 103.07 216.70 335.49 464.61 619.55 442 78.84 165.75 256.60 355.36 473.87
2.65 34 151.52 5.965 90 401.07 15.79 661 57.07 119.99 185.76 257.24 343.03 438 42.40 89.13 137.98 191.08 254.81
2.67 30 133.69 5.263 80 356.51 14.036 656 50.50 106.16 164.36 227.61 303.52 435 37.42 78.67 121.79 168.66 224.90
2.67 72 320.86 12.632 192 855.62 33.686 656 114.00 239.67 371.06 513.87 685.24 435 88.19 185.40 287.03 397.50 530.06
2.70 80 356.51 14.036 216 962.57 37.896 648 124.20 261.12 404.27 559.86 746.57 430 97.34 204.63 316.80 438.72 585.03
2.76 29 129.23 5.088 80 356.51 14.036 634 48.85 102.68 158.97 220.15 293.57 421 36.17 76.04 117.73 163.03 217.40
2.77 52 231.73 9.123 114 641.71 25.264 632 85.51 179.76 278.29 385.40 513.93 419 64.49 135.57 209.88 290.66 387.59
2.80 60 267.38 10.527 168 748.66 29.475 625 97.36 204.69 316.90 438.86 585.21 414 74.10 155.77 241.16 333.97 445.34
2.80 40 178.25 7.018 112 499.11 19.65 625 66.78 140.38 217.34 300.98 401.35 414 49.82 104.73 162.14 224.54 299.42
2.81 32 142.6 5.614 90 401.07 15.79 622 53.80 113.09 175.08 242.46 323.32 412 39.91 83.90 129.89 179.87 239.86
2.82 68 303.03 11.93 192 855.62 33.686 620 108.62 228.36 353.55 489.62 652.90 411 83.54 175.62 271.89 376.53 502.10
2.86 28 124.78 4.912 80 356.51 14.036 613 47.19 99.20 153.58 212.69 283.61 406 34.93 73.43 113.67 157.42 209.92
2.95 38 169.34 6.667 112 499.11 19.65 594 63.57 133.63 206.88 286.50 382.05 394 47.35 99.54 154.10 213.41 284.58
3 72 320.86 12.632 216 962.57 37.896 583 114.00 239.67 371.06 513.87 685.24 387 88.19 185.40 287.03 397.50 530.06
3 64 285.21 11.229 192 855.62 33.686 583 103.07 216.70 335.49 464.61 619.55 387 78.84 165.75 256.60 355.36 473.873 56 249.55 9.825 168 748.66 29.475 583 91.50 192.37 297.82 412.44 549.98 387 69.31 145.71 225.58 312.39 416.57
3 48 213.9 8.421 144 641.71 25.264 583 79.38 166.87 258.34 357.77 477.08 387 59.63 125.35 194.07 268.75 358.38
3 30 133.69 5.263 90 401.07 15.79 583 50.50 106.16 164.36 227.61 303.52 387 37.42 78.67 121.79 168.66 224.90
3.1 29 129.23 5.088 90 401.07 15.79 564 48.85 102.68 158.97 220.15 293.57 374 36.17 76.04 117.73 163.03 217.40
3.11 36 160.43 6.316 112 499.11 19.65 563 60.33 126.83 196.35 271.92 362.60 373 44.88 94.34 146.05 202.26 269.71
3.18 68 303.03 11.93 216 962.57 37.896 551 108.62 228.36 353.55 489.62 652.90 365 83.54 175.62 271.89 376.53 502.10
3.2 60 267.38 10.527 192 855.62 33.686 547 97.36 204.69 316.90 438.86 585.21 363 74.10 155.77 241.16 333.97 445.34
3.21 28 124.78 4.912 90 401.07 15.79 544 47.19 99.20 153.58 212.69 283.61 361 34.93 73.43 113.67 157.42 209.92
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.61
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)966 1190 1400 1610 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956
NUMBER OF BELT TEETH69 85 100 115 127 135 150 165 175 185 200 225 240 250 275 309 327 354
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)0.80 0.80 0.90 0.90 0.95 0.95 1.00 1.00 1.05 1.05 1.10 1.10 1.15 1.15 1.20 1.20 1.25 1.25
12.50 16.75 20.12 22.35 26.52 30.68 33.46 36.22 40.37 47.28 51.43 54.19 61.09 70.47 75.44 82.88
9.09 13.41 17.63 20.98 23.21 27.38 31.53 34.30 37.07 41.22 48.12 52.27 55.03 61.93 71.31 76.27 83.72
10.02 14.29 18.50 21.84 24.07 28.23 32.38 35.15 37.91 42.06 48.96 53.10 55.86 62.76 72.14 77.11 84.55
10.94 15.17 19.36 22.70 24.92 29.08 33.23 35.99 38.76 42.90 49.80 53.94 56.70 63.60 72.98 77.94 85.39
17.96 22.25 25.07 27.89 32.09 39.05 43.22 46.00 52.93 62.34 67.31 74.77
10.14 14.41 18.62 21.97 24.19 28.36 32.51 35.28 38.04 42.19 49.10 53.24 56.00 62.90 72.28 77.24 84.69
10.88 15.21 18.61 20.86 25.05 29.23 32.01 34.78 38.94 45.86 50.01 52.77 59.68 69.06 74.03 81.48
21.15 25.48 32.59 36.81 39.61 46.60 56.05 61.05 68.54
13.03 16.50 18.78 23.01 27.20 29.99 32.78 36.94 43.87 48.03 50.79 57.71 67.10 72.07 79.52
12.74 17.00 20.37 22.60 26.78 30.94 33.71 36.48 40.64 47.55 51.69 54.45 61.36 70.74 75.71 83.15
9.32 13.65 17.88 21.23 23.46 27.63 31.79 34.56 37.33 41.48 48.39 52.53 55.29 62.19 71.58 76.54 83.99
10.26 14.54 18.75 22.10 24.32 28.49 32.64 35.41 38.18 42.32 49.23 53.37 56.13 63.03 72.41 77.38 84.82
27.64 31.95 34.80 41.87 51.39 56.42 63.93
18.43 22.73 25.56 28.38 32.59 39.56 43.73 46.51 53.44 62.86 67.84 75.30
9.43 13.77 18.00 21.36 23.59 27.76 31.92 34.69 37.46 41.61 48.52 52.66 55.43 62.33 71.71 76.67 84.12
11.11 15.45 18.86 21.11 25.31 29.49 32.27 35.04 39.20 46.12 50.27 53.03 59.94 69.33 74.30 81.75
13.26 16.74 19.02 23.25 27.45 30.24 33.03 37.20 44.13 48.29 51.06 57.97 67.36 72.34 79.79
26.84 29.78 36.99 46.64 51.70 59.26
18.64 21.60 25.95 33.07 37.30 40.11 47.10 56.57 61.57 69.05
12.98 17.24 20.61 22.85 27.03 31.20 33.97 36.74 40.90 47.81 51.96 54.72 61.62 71.01 75.97 83.42
9.54 13.89 18.12 21.48 23.72 27.89 32.05 34.82 37.59 41.74 48.65 52.80 55.56 62.46 71.84 76.81 84.26
20.71 28.11 32.43 35.28 42.36 51.89 56.92 64.44
13.09 17.36 20.74 22.98 27.16 31.33 34.10 36.87 41.03 47.94 52.09 54.85 61.75 71.14 76.11 83.5613.49 16.97 19.26 23.50 27.70 30.50 33.28 37.46 44.39 48.55 51.32 58.23 67.63 72.60 80.06
11.33 15.69 19.10 21.35 25.56 29.74 32.52 35.30 39.46 46.38 50.53 53.30 60.21 69.60 74.57 82.02
14.46 18.89 23.20 26.05 28.87 33.08 40.07 44.24 47.02 53.96 63.38 68.36 75.83
19.09 22.06 26.42 33.56 37.79 40.60 47.60 57.07 62.08 69.57
8.78 13.21 17.48 20.86 23.10 27.29 31.46 34.23 37.00 41.16 48.07 52.22 54.98 61.89 71.27 76.24 83.69
21.15 28.57 32.90 35.76 42.84 52.39 57.42 64.95
13.72 17.21 19.50 23.74 27.95 30.75 33.54 37.71 44.65 48.81 51.58 58.49 67.89 72.87 80.32
11.56 15.93 19.34 21.60 25.81 29.99 32.78 35.56 39.72 46.64 50.79 53.56 60.47 69.86 74.83 82.28
23.20 27.74 30.70 37.94 47.61 52.68 60.26
32.80 42.69 47.83 55.48
11.67 16.04 19.46 21.72 25.93 30.12 32.90 35.68 39.85 46.77 50.92 53.69 60.60 69.99 74.96 82.42
19.53 22.51 26.89 34.04 38.28 41.09 48.10 57.58 62.59 70.08
21.59 29.03 33.37 36.23 43.33 52.89 57.92 65.45
14.90 19.35 23.68 26.53 29.36 33.58 40.57 44.75 47.53 54.48 63.90 68.88 76.35
13.94 17.44 19.73 23.99 28.20 31.00 33.79 37.96 44.91 49.07 51.84 58.76 68.16 73.13 80.59
23.63 28.19 31.15 38.41 48.09 53.17 60.75
11.78 16.16 19.58 21.84 26.06 30.24 33.03 35.81 39.98 46.90 51.06 53.82 60.73 70.13 75.10 82.55
15.12 19.58 23.92 26.77 29.60 33.82 40.82 45.00 47.79 54.73 64.16 69.14 76.61
26.09 33.71 43.63 48.79 56.45
24.06 28.63 31.60 38.88 48.58 53.66 61.2522.02 29.49 33.84 36.71 43.81 53.38 58.42 65.96
16.87 19.97 22.97 27.35 34.52 38.77 41.58 48.60 58.09 63.10 70.60
14.17 17.67 19.97 24.23 28.45 31.25 34.04 38.22 45.17 49.32 52.10 59.02 68.42 73.39 80.85
14.28 17.79 20.09 24.35 28.57 31.37 34.17 38.35 45.29 49.45 52.22 59.15 68.55 73.52 80.98
15.34 19.81 24.15 27.01 29.84 34.07 41.07 45.26 48.04 54.99 64.42 69.40 76.88
26.52 34.16 44.10 49.26 56.94
24.49 29.08 32.06 39.35 49.06 54.15 61.74
14.39 17.91 20.21 24.47 28.69 31.50 34.29 38.47 45.42 49.58 52.35 59.28 68.68 73.66 81.12
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
CENTER DISTANCES
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.
SPROCKET COMBINATIONS 1750 DRIVER RPM 1160 DRIVER RPMDRIVER DRIVEN HORSEPOWER RATING HORSEPOWER RATING
SPEED NO. P.D. P.D. NO. P.D. P.D. DRIVEN BELT WIDTHS (mm) DRIVEN BELT WIDTHS (mm)RATIO TEETH (mm) (in) TEETH (mm) (in) SPEED 20 42 65 90 120 SPEED 20 42 65 90 120
62
3.23 52 231.73 9.123 168 748.66 29.475 542 85.51 179.76 278.29 385.40 513.93 359 64.49 135.57 209.88 290.66 387.59
3.27 44 196.08 7.72 144 641.71 25.264 535 73.13 153.74 238.02 329.62 439.55 354 54.74 115.07 178.15 246.71 328.99
3.29 34 151.52 5.965 112 499.11 19.65 531 57.07 119.99 185.76 257.24 343.03 352 42.40 89.13 137.98 191.08 254.81
3.38 64 285.21 11.229 216 962.57 37.896 519 103.07 216.70 335.49 464.61 619.55 344 78.84 165.75 256.60 355.36 473.87
3.43 56 249.55 9.825 192 855.62 33.686 510 91.50 192.37 297.82 412.44 549.98 338 69.31 145.71 225.58 312.39 416.57
3.50 48 213.9 8.421 168 748.66 29.475 500 79.38 166.87 258.34 357.77 477.08 331 59.63 125.35 194.07 268.75 358.38
3.50 32 142.6 5.614 112 499.11 19.65 500 53.80 113.09 175.08 242.46 323.32 331 39.91 83.90 129.89 179.87 239.86
3.60 60 267.38 10.527 216 962.57 37.896 486 97.36 204.69 316.90 438.86 585.21 322 74.10 155.77 241.16 333.97 445.34
3.60 40 178.25 7.018 144 641.71 25.264 486 66.78 140.38 217.34 300.98 401.35 322 49.82 104.73 162.14 224.54 299.42
3.69 52 231.73 9.123 192 855.62 33.686 474 85.51 179.76 278.29 385.40 513.93 314 64.49 135.57 209.88 290.66 387.59
3.73 30 133.69 5.263 112 499.11 19.65 469 50.50 106.16 164.36 227.61 303.52 311 37.42 78.67 121.79 168.66 224.90
3.79 38 169.34 6.667 144 641.71 25.264 462 63.57 133.63 206.88 286.50 382.05 306 47.35 99.54 154.10 213.41 284.58
3.82 44 196.08 7.72 168 748.66 29.475 458 73.13 153.74 238.02 329.62 439.55 304 54.74 115.07 178.15 246.71 328.99
3.86 56 249.55 9.825 216 962.57 37.896 454 91.50 192.37 297.82 412.44 549.98 301 69.31 145.71 225.58 312.39 416.57
3 86 29 129.23 5.088 112 499.11 19.65 453 48.85 102.68 158.97 220.15 293.57 300 36.17 76.04 117.73 163.03 217.40
4 48 213.9 8.421 192 855.62 33.686 438 79.38 166.87 258.34 357.77 477.08 290 59.63 125.35 194.07 268.75 358.38
4 36 160.43 6.316 144 641.71 25.264 438 60.33 126.83 196.35 271.92 362.60 290 44.88 94.34 146.05 202.26 269.71
4 28 124.78 4.912 112 499.11 19.65 438 47.19 99.20 153.58 212.69 283.61 290 34.93 73.43 113.67 157.42 209.92
4.15 52 231.73 9.123 216 962.57 37.896 421 85.51 179.76 278.29 385.40 513.93 279 64.49 135.57 209.88 290.66 387.594.20 40 178.25 7.018 168 748.66 29.475 417 66.78 140.38 217.34 300.98 401.35 276 49.82 104.73 162.14 224.54 299.42
4.24 34 151.52 5.965 144 641.71 25.264 413 57.07 119.99 185.76 257.24 343.03 274 42.40 89.13 137.98 191.08 254.81
4.36 44 196.08 7.72 192 855.62 33.686 401 73.13 153.74 238.02 329.62 439.55 266 54.74 115.07 178.15 246.71 328.99
4.42 38 169.34 6.667 168 748.66 29.475 396 63.57 133.63 206.88 286.50 382.05 262 47.35 99.54 154.10 213.41 284.58
4.50 48 213.9 8.421 216 962.57 37.896 389 79.38 166.87 258.34 357.77 477.08 258 59.63 125.35 194.07 268.75 358.38
4.50 32 142.6 5.614 144 641.71 25.264 389 53.80 113.09 175.08 242.46 323.32 258 39.91 83.90 129.89 179.87 239.86
4.67 36 160.43 6.316 168 748.66 29.475 375 60.33 126.83 196.35 271.92 362.60 249 44.88 94.34 146.05 202.26 269.71
4.80 40 178.25 7.018 192 855.62 33.686 365 66.78 140.38 217.34 300.98 401.35 242 49.82 104.73 162.14 224.54 299.42
4.80 30 133.69 5.263 144 641.71 25.264 365 50.50 106.16 164.36 227.61 303.52 242 37.42 78.67 121.79 168.66 224.90
4.91 44 196.08 7.72 216 962.57 37.896 356 73.13 153.74 238.02 329.62 439.55 236 54.74 115.07 178.15 246.71 328.99
4.94 34 151.52 5.965 168 748.66 29.475 354 57.07 119.99 185.76 257.24 343.03 235 42.40 89.13 137.98 191.08 254.81
4.97 29 129.23 5.088 144 641.71 25.264 352 48.85 102.68 158.97 220.15 293.57 234 36.17 76.04 117.73 163.03 217.40
5.05 38 169.34 6.667 192 855.62 33.686 346 63.57 133.63 206.88 286.50 382.05 230 47.35 99.54 154.10 213.41 284.58
5.14 28 124.78 4.912 144 641.71 25.264 340 47.19 99.20 153.58 212.69 283.61 226 34.93 73.43 113.67 157.42 209.92
5.25 32 142.6 5.614 168 748.66 29.475 333 53.80 113.09 175.08 242.46 323.32 221 39.91 83.90 129.89 179.87 239.86
5.33 36 160.43 6.316 192 855.62 33.686 328 60.33 126.83 196.35 271.92 362.60 218 44.88 94.34 146.05 202.26 269.71
5.40 40 178.25 7.018 216 962.57 37.896 324 66.78 140.38 217.34 300.98 401.35 215 49.82 104.73 162.14 224.54 299.42
5.60 30 133.69 5.263 168 748.66 29.475 313 50.50 106.16 164.36 227.61 303.52 207 37.42 78.67 121.79 168.66 224.90
5.65 34 151.52 5.965 192 855.62 33.686 310 57.07 119.99 185.76 257.24 343.03 205 42.40 89.13 137.98 191.08 254.81
5.68 38 169.34 6.667 216 962.57 37.896 308 63.57 133.63 206.88 286.50 382.05 204 47.35 99.54 154.10 213.41 284.58
5.79 29 129.23 5.088 168 748.66 29.475 302 48.85 102.68 158.97 220.15 293.57 200 36.17 76.04 117.73 163.03 217.40
6 36 160.43 6.316 216 962.57 37.896 292 60.33 126.83 196.35 271.92 362.60 193 44.88 94.34 146.05 202.26 269.71
6 32 142.6 5.614 192 855.62 33.686 292 53.80 113.09 175.08 242.46 323.32 193 39.91 83.90 129.89 179.87 239.86
6 28 124.78 4.912 168 748.66 29.475 292 47.19 99.20 153.58 212.69 283.61 193 34.93 73.43 113.67 157.42 209.926.35 34 151.52 5.965 216 962.57 37.896 275 57.07 119.99 185.76 257.24 343.03 183 42.40 89.13 137.98 191.08 254.81
6.40 30 133.69 5.263 192 855.62 33.686 273 50.50 106.16 164.36 227.61 303.52 181 37.42 78.67 121.79 168.66 224.90
6.62 29 129.23 5.088 192 855.62 33.686 264 48.85 102.68 158.97 220.15 293.57 175 36.17 76.04 117.73 163.03 217.40
6.75 32 142.6 5.614 216 962.57 37.896 259 53.80 113.09 175.08 242.46 323.32 172 39.91 83.90 129.89 179.87 239.86
6.86 28 124.78 4.912 192 855.62 33.686 255 47.19 99.20 153.58 212.69 283.61 169 34.93 73.43 113.67 157.42 209.92
7.20 30 133.69 5.263 216 962.57 37.896 243 50.50 106.16 164.36 227.61 303.52 161 37.42 78.67 121.79 168.66 224.90
7.45 29 129.23 5.088 216 962.57 37.896 235 48.85 102.68 158.97 220.15 293.57 156 36.17 76.04 117.73 163.03 217.40
7.71 28 124.78 4.912 216 962.57 37.896 227 47.19 99.20 153.58 212.69 283.61 150 34.93 73.43 113.67 157.42 209.92
RPP PANTHER ULTRA-CORD BELT 14mm Belt Center Distance Selection
NOTE: SHORTEST CENTER DISTANCE SHOWN FOR EACH SPROCKET COMBINATION MAY NOT ACCOMMODATE INSTALLATION ALLOWANCE.63
THEORETICAL CENTER DISTANCE IN INCHES FOR VARIOUS BELT LENGTHSBELT LENGTH CODE (mm)966 1190 1400 1610 1778 1890 2100 2310 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956
NUMBER OF BELT TEETH69 85 100 115 127 135 150 165 175 185 200 225 240 250 275 309 327 354
MULTIPLY THE HORSEPOWER RATINGS BY THE BELT LENGTH CORRECTION FACTOR (KL)0.80 0.80 0.90 0.90 0.95 0.95 1.00 1.00 1.05 1.05 1.10 1.10 1.15 1.15 1.20 1.20 1.25 1.25
22.45 29.95 34.31 37.18 44.30 53.88 58.92 66.46
17.29 20.41 23.41 27.82 35.00 39.25 42.07 49.10 58.59 63.61 71.11
13.04 15.55 20.04 24.39 27.25 30.08 34.32 41.32 45.51 48.29 55.24 64.68 69.66 77.14
26.94 34.60 44.56 49.74 57.42
24.92 29.52 32.51 39.81 49.54 54.64 62.24
22.89 30.40 34.77 37.65 44.78 54.37 59.42 66.97
13.25 15.77 20.27 24.62 27.48 30.33 34.56 41.57 45.76 48.55 55.50 64.93 69.92 77.40
27.37 35.05 45.03 50.21 57.90
17.71 20.84 23.86 28.28 35.47 39.73 42.56 49.59 59.10 64.11 71.62
25.35 29.96 32.96 40.28 50.02 55.12 62.73
13.46 15.99 20.50 24.86 27.72 30.57 34.80 41.82 46.01 48.80 55.75 65.19 70.18 77.66
17.92 21.06 24.09 28.51 35.71 39.98 42.80 49.84 59.35 64.37 71.88
23.32 30.86 35.24 38.12 45.26 54.86 59.91 67.47
24.52 27.79 35.49 45.49 50.68 58.38
13.56 16.10 20.61 24.97 27.84 30.69 34.93 41.94 46.14 48.92 55.88 65.32 70.31 77.79
25.77 30.41 33.41 40.74 50.50 55.61 63.22
18.13 21.28 24.31 28.74 35.95 40.22 43.05 50.08 59.60 64.62 72.13
13.67 16.21 20.72 25.09 27.96 30.81 35.05 42.07 46.26 49.05 56.01 65.45 70.44 77.92
24.93 28.21 35.94 45.96 51.15 58.8618.87 23.75 31.31 35.70 38.59 45.74 55.35 60.41 67.97
18.34 21.50 24.53 28.97 36.19 40.46 43.29 50.33 59.85 64.87 72.39
26.20 30.85 33.86 41.20 50.97 56.09 63.71
19.07 23.96 31.54 35.93 38.82 45.98 55.60 60.66 68.22
25.34 28.64 36.38 46.42 51.62 59.34
18.55 21.71 24.76 29.20 36.42 40.70 43.53 50.58 60.10 65.12 72.64
19.28 24.18 31.76 36.16 39.06 46.22 55.84 60.90 68.47
26.62 31.28 34.30 41.67 51.45 56.57 64.20
18.76 21.93 24.98 29.42 36.66 40.94 43.77 50.82 60.35 65.37 72.90
25.75 29.06 36.82 46.88 52.09 59.82
19.48 24.39 31.99 36.39 39.29 46.46 56.09 61.15 68.72
18.87 22.04 25.09 29.54 36.78 41.06 43.89 50.95 60.47 65.50 73.02
26.84 31.50 34.53 41.90 51.69 56.81 64.44
18.97 22.15 25.20 29.65 36.89 41.18 44.02 51.07 60.60 65.63 73.15
19.68 24.61 32.21 36.62 39.52 46.69 56.33 61.40 68.96
27.05 31.72 34.75 42.13 51.93 57.05 64.69
26.16 29.48 37.26 47.34 52.56 60.30
19.89 24.82 32.44 36.85 39.76 46.93 56.57 61.64 69.21
27.26 31.94 34.97 42.36 52.16 57.29 64.93
26.37 29.69 37.49 47.57 52.79 60.53
19.99 24.92 32.55 36.97 39.87 47.05 56.69 61.76 69.34
26.57 29.90 37.71 47.80 53.02 60.77
27.47 32.16 35.19 42.59 52.40 57.53 65.17
20.09 25.03 32.66 37.08 39.99 47.17 56.82 61.89 69.4626.77 30.11 37.92 48.03 53.26 61.01
27.68 32.38 35.41 42.81 52.64 57.77 65.42
27.79 32.49 35.53 42.93 52.75 57.89 65.54
26.98 30.32 38.15 48.26 53.49 61.25
27.89 32.60 35.64 43.04 52.87 58.01 65.66
27.18 30.52 38.36 48.49 53.72 61.48
21.67 27.28 30.63 38.47 48.60 53.84 61.60
21.77 27.38 30.73 38.58 48.72 53.96 61.72
64
Trouble Shooting Guide For Synchronous Drives
TABLE 17 – CAUSES OF PREMATURE BELT AND SPROCKET FAILURECauses
Belt tension excessively high
Excessive load
Incorrect contour or diameter of sprocket
Excessive installation tension
Incorrect diameter of sprocket
Incorrect contour or diameter of sprocket
Excessive load
Misalignment or improper positioningof sprockets
Shaft Runout
Damaged flanges
Diameter of sprocket below minimum
Belt pitch too small
Insufficient tension
Insufficient teeth in mesh
Insufficient teeth in mesh
Excessive load
Insufficient tension
Excessive load
Diameter of sprockets below minimum
Exposure to excessively low temperature startup (below -32°F) or excessively high continuous temperature (over +230°F)
Diameter of sprocket less than the minimum recoommended
Operation with excessive amount of oil present
Reduction of center distance
Excessive overloading
Belt tension excessively high
Sprocket material of insufficient hardness
Abrasive material present
Sprockets out of alignment
Excessive installation tension
Diameter of sprockets below minimum
System harmonics
Corrective Action
Reduce center distance
Use a wider belt
Replace sprocket
Reduce center distance
Replace sprocket after checking the diameter
Replace sprocket after checking contour
Use a wider belt
Correct the positioning of the sprockets
Check for eccentricity
Repair or replace flanges
Increase the diameter of the sprockets
Use belts and sprockets of larger pitch
Increase center distance
Increase the number of teeth in mesh
Increase the number of teeth in mesh
Use a wider belt
Increase center distance
Use a wider belt
Increase the diameter of the sprockets
Eliminate the extreme temperature
Increase the diameter of the sprockets or usebelts and sprockets of smaller pitch
Eliminate or reduce the amount of oil present
Restore the initial center distance
Use a wider belt
Reduce the center distance
Harden the sprocket surface or select harder sprocket material
Eliminate abrasive atmosphere
Align sprockets
Reduce the center distance
Increase the diameter of the sprockets resulting in reduced belt tension requirement
Redesign drive
Failure Modes
Abnormal wear of the BELT:a) on the side of the tooth
(driving surface)
b) Between the teeth (land area)
c) At the tooth root
d) On the side of the belt
Tooth Jump
Tooth shear
Rupture of tensile member
Breaks or cracks in the top surfaceof the belt
Softening of the top surface of the belt
Apparent elongation of the belt
Excessive wear of SPROCKET
Excessively noisy SYSTEM
65
Engineering Data
SPROCKET DIAMETER AND SPEED
Blanks in the Belt Horsepower Rating tables indicate therim speeds exceed the safe operating speed of 6500 feetper minute for cast iron sprockets. For rim speedsgreater than 6500 feet per minute, contact CarlisleEngineering for other recommendations.
FLANGED SPROCKETS
Due to tracking characteristics, even on the best aligned drives, all synchronous belts have a tendency tomove axially and will ride off the edge of the sprockets.In order to keep the belt on the sprocket, side flanges are needed.
On all synchronous drives the following conditionsshould be considered when selecting flanged sprockets.
1. Two Sprocket Drives: One sprocket must haveflanges on both sides or both sprockets must haveone flange but on opposite sides.
2. Long Center Drives: When the center distance isequal to or greater than eight times the small sprocket diameter, both sprockets should be flanged.
3. Vertical Shaft Drives: One sprocket should beflanged on both sides, and all other sprockets in thedrive system should have one flange on the bottomside.
4. Multiple Sprocket Drives: Every other sprocket in thesystem should be flanged on both sides or one flange on each sprocket alternating sides around theentire system.
On many synchronous drive applications, you won’t haveto be concerned about flanged sprockets, because mostof the smaller sprockets (up to and including 80 teeth)are already furnished with flanges on both sides of thesprocket. A flanged sprocket is identified by a letter “F”in the type column in the stock sprocket dimensionaltables.
Safety Note � WARNING!FAILURE TO FOLLOW RECOMMENDED APPLICATIONINFORMATION AND RECOMMENDED PROCEDURES FORINSTALLATION, CARE, MAINTENANCE AND STORAGE OFBELTS MAY RESULT IN FAILURE TO PERFORM PROPER-LY AND MAY RESULT IN DAMAGE TO PROPERTY ANDSERIOUS BODILY INJURY. MAKE SURE THAT BELTSSELECTED FOR ANY APPLICATION ARE RECOMMENDEDFOR THAT SERVICE.
FIXED CENTERS(NO ADJUSTMENT)
True fixed center applications are those where no provision has been made to adjust either the driveR ordriveN shaft. Fixed centers are not recommended forany synchronous belt drive other than motion transfer(low or no torque) drives. Fixed center applications implythe need for exact tolerances. Although length tolerances for synchronous belts are considerably lessthan those for other belts, such as v-belts, etc., no beltcan be manufactured without some tolerance. Sprocketmanufacturing tolerances also contribute to fixed centerdrive problems. Fixed center applications do not allow for proper belt installation and tensioning practices and prevent accepted maintenance procedures.
Because fixed center applications prevent proper beltinstallation and tensioning procedures, reduced belt performance can result. Through the use of an idler, theproblems associated with fixed center drives can be eliminated. See engineering section on use and application of idlers.
IDLERS
The use of an idler should be limited to those applicationswhere it is absolutely necessary, such as fixed centerdrives. A common serious fault is the use of idlers whichare too small. The use of such idlersintroduces severe bending stresses in the belt resultingin reduced belt life.
An idler may be located on either the inside or outsideof the belt drive, but in either case should be on the slackside (lower tension belt span). An inside idler (groovedsprocket) should not be smaller than the smallest loadedsprocket in the drive system. A flat, uncrowned, idler pul-ley may also be used on the inside as long as its diameteris equivalent to the diameter of a 40 groove sprocket, ormore.
Outside idlers are always flat, uncrowned, pulleys.Diameters should be a minimum of 1.3 times larger thanthe smallest loaded sprocket in the system. Arc ofcontact shouldbe kept to a minimum to reduce the reverse bendingstresses on the belt.
Spring-loaded idlers are not recommended for usewith synchronous belt drives. This is due to the abilityof synchronous belts to self-generate sufficient tensionto overcome any reasonable spring force. The belt willjump teeth in this situation because the effectivenessof the spring has been eliminated. Additional springforce will only impose higher belt tension which may beexcessive and dramatically reduce the belt life.
66
Engineering Data
BELT INSTALLATION AND TENSIONING ALLOWANCESSince fixed center drives are not recommended, center distance adjustment for Carlisle’s RPP® PANTHER drive systems are necessary to assure that the belt can be installed without damaging it and then allow for correct belttensioning. The tables below show the needed allowances for installation and tensioning for all belt pitches and lengths.
BELT TOLERANCE
Inches Millimeters Up to 33” 33 to 66” Over 66”
7/16 to 1 1/2 11.1 to 38.1 +1/32-1/32 +1/32-3/64 +1/32-3/641 1/2 to 2 38.1 to 50.8 +1/32-3/64 +3/64-3/64 +3/64-1/162 to 2 1/2 50.8 to 63.5 +3/64-3.64 +3/64-1/16 +1/16-1/162 1/2 to 3 63.5 to 76.2 +3/64-1/16 +1/16-1/16 +1/16-5/64
3 to 4 76.2 to 101.6 +1/16-1/16 +1/16-5/64 +5/64-5/644 to 7 101.6 to 177.8 +3/32-3/32 +1/16-5/64 +5/64-5/64Over 7 over 177.8 +3/16-1/4
STOCK BELT WIDTH TOLERANCES
BELT WIDTHS BELT LENGTH (INCHES)
SPROCKET TOLERANCESRPP® PANTHER sprockets are made with precision tolerances. Inaccurate manufacture or reboring may result inunsatisfactory drive performance. Consequently, conformity to the standard tolerances (as shown in table) is highlyrecommended.
SPROCKET DIAMETER TOLERANCES
Diameters (inches) Tolerances
2.001 to 4.000 +.004 - .0004.001 to 7.000 +.005 - .0007.001 to 12.000 +.006 - .00012.001 to 20.000 +.007 - .000
20.001 — up +.008 - .000
BORE TOLERANCES (inches)
Diameters (inches) Tolerances
Up to 1 +.0010 -.0000
1 to 2 +.0015 - .00002 to 3 +.0020 - .00003 up +.0025 - .0000
BALANCINGCast iron Sprockets will be statically balanced (oneplane) to a maximum residual unbalance of (.1 xweight of sprocket, lb.) oz. in. Check the graph 1on page 22 (balancing standards) to determine if adynamic (2 plane) balance is required.
ECCENTRICITYAllowable amount of eccentricity from sprocketbore to outside diameter (OD)
OD (inches) Total Eccentricity(indicator reading) (inches)
To 8 .005.0005 per in. of diameter
Over 8 (may not exceed the toleranceon face diameter)
Belt Pitch Standard installation RequiredLength Range Allowance (Flanged Tensioning
(in.) Sprockets Removed AllowanceFor Installation) (Any Drive)
(in.) (in.)
0 - 30 0.070 0.03031 - 60 0.110 0.03561 - 110 0.130 0.040111 - 160 0.160 0.045161 - 200 0.190 0.050
For Installation Over Flanged Sprockets (Add to Installation Allowance in Table 13)
Sprocket Additional Allowance if BothPitch Small Sprocket is the only Sprocket
Flanged Sprocket Flanged(in.) (in.)
8mm 0.60 1.2014mm 0.90 2.10
Table 13 - Center Distance Allowance Table 14 - Additional Center DistanceFor Installation and Tensioning Allowance
67
Synchronous Drive Systems Installation
The synchronous belt drive will perform successfully when proper installation procedures are followed.
SPROCKET INSTALLATION
1. Thoroughly inspect the bore of the sprocket and thetapered surface of the bushing. Any paint, dirt, oil orgrease must be removed.
2. Assemble bushing into sprocket. Loosely insert thecapscrews into assembly, but do not lubricate capscrew threads. (Note: Install M thru S bushingsso the two extra holes in the hub are located as far aspossible from the bushing’s sawcut.)
3. With key in keyseat of shaft, slide sprocket to itsdesired position with capscrew heads to the outside.(A few small sprockets may have to be installed withthe capscrews on the inside.) If it is hard to slide thebushing onto the shaft, wedge a screwdriver bladeinto the sawcut to overcome the tightness.
4. Line up assembly so as not to misalign belts, and tight-en capscrews evenly and progressively. Apply the rec-ommended torque to capscrews. There should be 1/8”to 1/4” gap between the sprocket hub and the bushingflange. If gap is closed, the bushing is oversized andthe next smallest bushing should be used.
SPROCKET ALIGNMENT
Sprocket alignment and parallelism of the shafts are veryimportant. Proper alignment helps to equalize the loadacross the entire belt width, thereby reducing wear andextending belt life.PLACE A STRAIGHTEDGE against the outside edge of
the sprockets and move sprockets until the straightedgetouches the two outside and two inside edges of sprock-ets. The straightedge should cross the sprockets as nearthe shafts as possible. A string can be used if a straight-edge is not available. Remember the string should con-tact at four points as explained above.
After aligning the sprockets, check the rigidity of thesupporting framework. Shafts should be well supportedto prevent distortion and a resulting change in the centerdistance under load. Do not use springloaded or weight-ed idlers. Idler sprockets or pulleys must be locked intoposition after adjusting belt tension.
Please note: at least one sprocket must have a flange.
An alternate method can be used to properly tension thebelt on a synchronous drive. After the drive has beeninstalled and tension applied, the deflection force can bemeasured to verify the proper tension. Stop the driveand measure the belt span (see sketch). Using a springscale, apply a perpendicular force to the exact center ofthe belt width and near the center of the belt span.Measure the force required to deflect the belt 1/64 inchfor every inch of span length. For example, the deflectionfor a 32 inch span would be 1/64 multiplied by 32, or 1/2inch.
Actual installation tension required depends on peakloads, system rigidity, number of teeth in mesh, etc. Fordrives with shock loading or other unusual conditions, theforce may have to be increased for proper operation ofthe drive.
Note: For belts wider than 2 inches, it is suggested thata rigid strip of keystock or something similar be placedacross the belt between the point of force and the belt toprevent belt distortion.
Safety Note �WARNING!FAILURE TO FOLLOW RECOMMENDED APPLICATIONINFORMATION AND RECOMMENDED PROCEDURES FORINSTALLATION, CARE, MAINTENANCE AND STORAGE OFBELTS MAY RESULT IN FAILURE TO PERFORM PROPER-LY AND MAY RESULT IN DAMAGE TO PROPERTY AND SERIOUS BODILY INJURY. MAKE SURE THAT BELTSSELECTED FOR ANY APPLICATION ARE RECOMMENDEDFOR THAT SERVICE.
BELT INSTALLATIONDo not pry or otherwise force the belt onto the sprockets, as this can result in permanent damage to thebelt. Either remove the sprocket’s outside flange orreduce the center distance between the pulleys so thatthe belt can be easily installed.
Synchronous belts are not to be tensioned as you woulda V-Belt or any other belt that depends on friction totransmit the load. They should be installed with a snugfit, neither too taut nor too loose.
SPAN LENGTH
DEFLECTION FORCE
DEFLECTION
Calculate the installation tension (Ts) using the following formula:
Ts (lbs) = 81938 * HPDia. * RPM
Where: HP = Motor base horsepower.Dia. = DriveR sprocket pitch diameter (inches).RPM = DriveR sprocket speed.BW = Belt Width (mm).Mass = Mass Factor
+ 4.399X10-7 * BW * Mass * Dia.2 * RPM2
Pitch Width Min Ts
8mm 12mm 3022mm 6035mm 10160mm 187
14mm 20mm 7742mm 18065mm 29690mm 429120mm 595
Pitch Mass Factor
8mm 0.00525
14mm 0.01030
68
Drive Assistance Data Sheet
CONTACT PERSON ___________________________ COMPANY _______________
PHONE#_____________________________________ FAX # ___________________
DATE _______________________________________
DRIVEN APPLICATION _________________________ (Required to select service factor)
DRIVER DATA:
MOTOR TYPE & DESCRIPTION ____________________________________________
MOTOR HP _________________RPM ________________SHAFT DIAMETER _______
GEARBOX; YES/NO, IF YES; RATIO ______________OR OUTPUT RPM ___________
SHAFT DIAMETER _________________MAXIMUM PULLEY DIAMETER ___________
_________________________________MAXIMUM PULLEY WIDTH _______________
DRIVEN DATA:
DESIRED RPM ______________OR RATIO ____________(SPEED UP/SPEED DOWN)
SHAFT DIAMETER _________________MAXIMUM PULLEY DIAMETER ___________
_________________________________MAXIMUM PULLEY WIDTH _______________
CENTER DISTANCE RANGE:
MINIMUM_________________NOMINAL ______________MAXIMUM ______________
CENTER DISTANCE ADJUSTMENT:
ADJUSTABLE BASE______________PIVOTED BASE __________FIXED ___________
IDLER: INSIDE_______ BACKSIDE_______ SLACK SIDE_______ TIGHT SIDE_______
DUTY CYCLE:
8 HOURS/DAY___________ 16 HOURS/DAY__________ 24 HOURS/DAY__________
ENVIRONMENT:
TEMPERATURE _____°F OIL_____ DUST_____ WATER_____ ABRASIVES______
START UP CHARACTERISTICS:
SOFT START_______ CLUTCH_________ NO LOAD_______ FULL LOAD ________
REMARKS: _____________________________________________________________
_______________________________________________________________________
EXISTING DRIVE:
CHAIN ______________ V-BELT _______________ COMPETITOR______________
DESIGN REQUIRED BY (DATE) ____________________________________________
COMPLETE DRIVE SKETCH ON ADDITIONAL PAGE IF POSSIBLE
DRIVE ASSISTANCE DATAFAX INFORMATION DIRECTLY TO YOUR APPLICATION ENGINEER
Synchronous Drive Systems Data Sheet