Drinking Water Systems 103
DrinkingWater
Systems
103
104 Hydrotech
The following chart on conditions for use is applicable to all the reverse osmosis systems listed.
The following pages of Hydrotech Reverse Osmosis Systems describe the two ways you can order.
A.Order by STANDARD Item Number which comes complete with Faucet and Storage Tank.
Complete system includes
• Reverse osmosis system manifold, with cartridges, membrane
and installation kit
• Chrome Faucet
• Metal storage tank
B.Order separate SYSTEM, FAUCET and STORAGE TANK by using the optional component pages
Reverse Osmosis Drinking Water Systems
+
Conditions for Use
+
Source Water Supply Profile Chemical Parameters Max mg/L
Notes: 1Pressure Regulator is recommended for feed water pressures exceeding 552 kPa (80 psig). The performance of a reverse osmosis
membrane is highly dependent upon pressure, temperature and TDS. The actual volume of product water and rejection percentage will vary
with differences from the test conditions that membrane ratings are based upon. These drinking water systems are not intended to be used
for the treatment of water that is microbiologically unsafe or of unknown quality. Storage tank capacity is dependent on pressure. Example:with a 5 psi precharge, the drawdown volume is 3.2 gal at 60 psi, 2.8 gal at 40 psi for the storage tank shown.
Smartap® U.S. patents: 5,145,575; 5,435,909; 5,580,444; 5,527,450
Community/Private Chlorinated/Non-Chlorinated Hardness (CaCO3) <350 (< 20 gpg)
Feed Water Pressure1 242 – 690 kPa (35-100 psig) Iron (Fe) <0.1
Temperature 4° – 38°C (40° – 100°F) Manganese (Mn) <0.05
pH Range 3.0 – 11.0 Hydrogen Sulfide (H2S) 0.00
Maximum TDS Level 2000 mg/L Residual Chlorine (Cl2) <2.0
Turbidity** <1.0 NTU **Nephelometric Turbidity Unit
Maximum SDI*** <4.0 ***Silt Density Index: Value stated in SDI units.
105Hydrotech
Reverse Osmosis Drinking Water Systems1240 Series Models and System Configurations
Order the systems listed above, which come complete with everything listed on this page.
* Manufacturer’s output specification only with inlet conditions of 372 kPa (60 psig), 25°C (77°F), going to atmosphere.**These models are tested and certified by WQA against NSF/ANSI 58 for the reduction of TDS. Tested and certified by WQA against ORD0902 for “lead free” compliance. WQA Tested and
Certified against CSA B483.1
PRO SERIESPremier Push Button Monitored
Reverse Osmosis Systems
Our premier model is equipped with our
patented Smartap® Push Button Monitor. At
the touch of a button you can be assured
that you are receiving top quality water or
you will be alerted that it is time to change
your membrane. This model also utilizes
three dedicated sediment and carbon filters.
All models include:
• High quality reverse osmosis membrane
• Choice of 9, 25, 50 and 75 gpd
• Sediment pre-filtration
• Pre & post carbon block filtration
• Quick connect fittings
• 3/8” tubing from RO to tank and faucet
for higher flow
• Color coded tubing for ease of
installation
• Air gap chrome faucet
• Storage tank
M SERIESHigh Quality Four-Stage Reverse
Osmosis Systems
This model produces great tasting
drinking water in the exact same fashion
as our Pro Series. The only difference
with this model is that it does not include
the patented Smartap® Push Button
Monitor.
All models include:
• High quality reverse osmosis
membrane
• Choice of 9, 25, 50 and 75 gpd
• Sediment pre-filtration
• Pre & post carbon block filtration
• Quick connect fittings
• 3/8” tubing from RO to tank and
faucet for higher flow
• Color coded tubing for ease of
installation
• Air gap chrome faucet
• Storage tank
E SERIESCompact Three-Stage Reverse
Osmosis Systems
The E Series utilizes a combination
sediment and carbon pre-filter instead of
separate dedicated sediment and
carbon pre-filters. This system is great
for installing in tight spaces or for those
looking for the most economical
solution.
All models include:
• High quality reverse osmosis
membrane
• Choice of 25 and 50 gpd
• Sediment pre-filtration
• Pre & post carbon block filtration
• Quick connect fittings
• 3/8” tubing from RO to tank and
faucet for higher flow
• Color coded tubing for ease of
installation
• Chrome faucet
• Storage tank
Hydrotech Model Sediment Output*Item # Description Vessels Filter Pre-Filter Membrane Post-Filter GPD Monitor
1240101-00 3VTFC25G 3 None Dual-Purpose Thin Film Composite Activated Carbon 25 None
1240102-00 3VTFC50G 3 None Dual-Purpose Thin Film Composite Activated Carbon 50 None
1240200-00 4VTFC09G 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 9 None
1240201-00 4VTFC25G 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 25 None
1240202-00 4VTFC50G 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 50 None
1240203-00 4VTFC75G 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 75 None
1240300-00 4VTFC09G-PB** 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 9 Push Button
1240301-00 4VTFC25G-PB** 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 25 Push Button
1240302-00 4VTFC50G-PB** 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 50 Push Button
1240303-00 4VTFC75G-PB** 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 75 Push Button
All PRO SERIES models are tested andcertified by WQA against NSF/ANSI 58 forthe reduction of TDS. Tested and certifiedby WQA against ORD0902 for “lead free”compliance.
All PRO SERIES models are WQA Testedand Certified against CSA B483.1
106 Hydrotech
Three Vessel
Item # Model #
1240101-0 3VTFC25G
1240102-0 3VTFC50G
Four Vessel
Item # Model #
1240200-0 4VTFC9G
1240201-0 4VTFC25G
1240202-0 4VTFC50G
1240203-0 4VTFC75G
Four VesselPush Button Monitored
Item # Model #
1240300-0 4VTFC9G-PB
1240301-0 4VTFC25G-PB
1240302-0 4VTFC50G-PB
1240303-0 4VTFC75G-PB
Order basic RO manifold above with faucet and tank featured below.
Reverse Osmosis Drinking Water SystemsStandard Models with Optional Faucet and Storage Tanks
Air Gap Faucets
Item # Description
40301001 Chrome
87512 White
87515 Brass
87516 Almond
40301004 Stainless Steel
40302018 Satin
87520 Bisque
87518 Black
Non Air Gap Faucets
Item # Description
87513 Chrome
87514 White
87517 Brass
87519 Almond
87521 Brushed Nickel
87522 Polished Nickel
40301003 Stainless Steel
Non Air Gap Faucets
Item # Description
87511 Chrome Long Reach
Air Gap Faucets
Item # Description
92192 Chrome Long Reach
Standard Faucets QMP Faucets (Prop 65 Compliant)
Item Model
92313 3.8 Gallon ROPro Polypropylene
Tank w/ valve
42600029 PAE 4.0 Gallon Metal Tank w/ valve
9405 Structural Romate 15
9404 Structural Romate 20
9403 Structural Romate 30
9402 Structural Romate 40
9401 Structural Romate 80
Item Model
92324 Amtrol RO-2, 2 Gallon Tank
92288 Amtrol RO-3, 3 Gallon Tank
92294 Amtrol RO-4, 4 Gallon Tank
92282 Amtrol RO-14, 14 Gallon Tank
92325-1 Amtrol RO-20, 20 Gallon Tank
92326 Amtrol RO-34, 34 Gallon Tank
92322 Amtrol RO-44, 44 Gallon Tank
92323-1 Amtrol RO-86, 86 Gallon Tank
Storage Tanks
107Hydrotech
Economy RO Drinking Water SystemsAll models include: 3/8”outlet tubing for higher flows, thin film composite (TFC) membranes, quick connect
fittings for easy installation and servicing, heavy duty powder coated bracket, stainless steel product water check
valve, automatic shut-off valve, 4.0 U.S. gallon (15 litre) storage tank and under counter installation kit.
Economy RO Model ComponentsReverse Osmosis Membrane - allows water molecules to pass while dissolved impurities are flushed to the drain.
Five Micron Pre-Filter - removes tiny particles of suspended dirt and sediment.
Activated Carbon Pre-Filter - protects TFC membrane from chlorine and removes organics.
Activated Carbon Post Filter - removes tastes and odors to give water a final “polish” prior to delivery.
Pressurized Storage Tank - holds purified drinking and cooking water ready for use.
Chrome Plated Faucet - mounts attractively on sink or counter to deliver pure water at the touch of a lever.
Economy RO Booster Pump Model Specific ComponentsBooster Pump - raises and maintains the water pressure at the optimum level to ensure the highest TDS rejection
rate with maximum production.
Product Water Pressure Switch - shuts off system when pressure tank has been filled.
Feed Water Pressure Switch - protects pump against run dry situations.
The performance of a reverse osmosis membrane is highly dependent upon pressure, temperature and TDS. The actual volume of product water and rejection percentage willvary with differences from the test conditions that membrane ratings are based upon. These drinking water systems are not intended to be used for the treatment of water thatis microbiologically unsafe or of unknown quality.
Conditions for UseSource Water Supply Profile
Community/Private Chlorinated/Non-Chlorinated Hardness (CaCO3) <10 gpg / NSF: <350 (< 20 gpg)Feed Water Pressure* 242 – 690 kPa (35 – 100 psig) Iron (Fe) <0.1Temperature 4° – 38°C (40° – 100°F) Manganese (Mn) <0.05pH Range 3.0 – 11.0 Hydrogen Sulfide (H2S) 0.00Maximum TDS Level 2000 mg/L Residual Chlorine (Cl2) <2.0Turbidity** <1.0 NTUMaximum SDI*** <4.0
*Pressure regulator isrecommended for feed waterpressures exceeding 552 kpa(80 psig)
** Nephelometric Turbidity Unit*** Silt Density Index: Value stated
in SDI units.
Chemical Parameters Max mg/L
(1)Nominal product water ratings are based on the following conditions: Supply TDS of 250 ppm softened tap water, 50 psi (0.36 Mpa), 77°F (25°C), pH 8 and 15% recoverywith outlet to atmosphere.
(2)TDS rejection percentages are dependent on the supply conditions and the substance being measured.(3)Storage tank capacity is dependent upon pressure. For example, with a 5 psi precharge, the drawdown volume is 3.2 gallons at 60 psi; 2.8 gallons at 40 psi.
Specifications
Economy Reverse Osmosis Systems
Item Model Sediment Output Rejection Storage TankNumber Description Stages Filter Pre-Filter Membrane Post-Filter GPD(1) %(2) US Gallons(3)
2872 E50TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 50 up to 4.0
2873 E75TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 75 99% 4.0
Model E50TFC-3SF features:• Reverse osmosis membrane, nominally rated at 50 U.S. gallons per day.
• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated
Carbon Cartridge
• Post filter: 10" Activated Carbon Cartridge
• Non air gap faucet
• Metal storage tank
Model E75TFC-3SF features:• Reverse osmosis membrane, nominally rated at 75 U.S. gallons per day.
• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated
Carbon Cartridge
• Post filter: 10" Activated Carbon Cartridge
• Non air gap faucet
• Metal storage tank
108 Hydrotech
(1)Nominal product water ratings are based on the following conditions: Supply TDS of 250 ppm softened tap water, 50 psi (0.36 Mpa), 77°F (25°C), pH 8 and 15% recoverywith outlet to atmosphere.
(2)TDS rejection percentages are dependent on the supply conditions and the substance being measured.(3)Storage tank capacity is dependent upon pressure. For example, with a 5 psi precharge, the drawdown volume is 3.2 gallons at 60 psi; 2.8 gallons at 40 psi.
Specifications
Economy Reverse Osmosis Systems c/w Booster Pump
Economy Reverse Osmosis Systems WQA Approved
Item Model Sediment Output Rejection Storage TankNumber Description Stages Filter Pre-Filter Membrane Post-Filter GPD(1) %(2) US Gallons(3)
2875 EBP75TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 75 up to 99% 4.0
Model EBP75TFC-3SF features:
• Reverse osmosis membrane, nominally rated at 75 U.S. gallons per day.
• Booster Pump: Mounted on RO to maintain constant water pressure.
• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated
Carbon Cartridge
• Post filter: 10" Activated Carbon Cartridge
• Non air gap faucet
• Metal storage tank
Model E50TFC-3NSF features:
• WQA Gold Seal tested and certified to NSF/ANSI 58
• Reverse osmosis membrane, nominally rated at 50 U.S. gallons per day.
• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated Carbon
Cartridge
• Post filter: 10" Activated Carbon Cartridge
• Non air gap faucet
• Air gap kit
• Metal storage tank
Model E75TFC-3NSF features:
• WQA Gold Seal tested and certified to NSF/ANSI 58
• Reverse osmosis membrane, nominally rated at 75 U.S. gallons per day.
• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated Carbon
Cartridge
• Post filter: 10" Activated Carbon Cartridge
• Non air gap faucet
• Air gap kit
• Metal storage tank
(1) TFC refers to reverse osmosis membranes constructed from a THIN FILM COMPOSITE(2) The daily production rate is the volume of product water produced by the system per day and is determined by testing in accordance with the procedure outlined in NSF/ANSI
Standard 58.(3) System’s Efficiency rating as verified by testing in accordance with NSF/ANSI standard 58. Efficiency rating means the percentage of the influent water to the system that
is available to the user as reverse osmosis treated water under operating conditions that approximate typical daily usage.(4) System’s Recovery rating as verified by testing in accordance with NSF/ANSI Standard 58. System’s Recovery rating means the percentage of the influent water to the membrane
portion of the system that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed.*PRESSURE REGULATOR IS RECOMMENDED FOR FEED WATER PRESSURES EXCEEDING 552 kPa (80 psig)
SpecificationsItem Model # of Storage Tank Vessel Vessel Vessel Vessel Daily Prod. Rate(2) Efficiency Recovery
# Description Vessels Capacity Ltr (gal) 1 2 3 4 L/day (G/day) Rating(3) % Rating(4) %2887 E50TFC-3NSF 4 6 (1.6) Sediment Filter Carbon Filter TFC(1) Membrane Carbon Filter 45.4 (12) 8.5 17.5
2888 E75TFC-3NSF 4 8.7 (2.3) Sediment Filter Carbon Filter TFC(1) Membrane Carbon Filter 100 (26.4) 14.5 25.8
The following Economy Reverse Osmosis Systems conform to NSF/ANSI 58 for the specific performance claims as
verified and substantiated by test data.
Economy RO Drinking Water Systems
Models E50TFC-3NSF and E75TFC-3NSF are tested and certified byWQA against NSF/ANSI 58 for thereduction of TDS.
Models E50TFC-3NSF and E75TFC-3NSF are WQA Tested and Certifiedagainst CSA B483.1
109Hydrotech
Reverse Osmosis Designer Faucets
The Tomlinson Designer RO Faucet comes in nine
beautiful finishes to match today's designer kitchens.
This lead-free designer faucet retrofits to most brands
and is an excellent upgrade from basic faucets that
come with most RO and other Filter Systems.
Features:
• Combines quality and style
with up-sell appeal
• Retrofits most brands
• Smooth operating ceramic
disk element
• Lever style handle
• Standard finish is highly
polished chrome; other
designer finishes available
• High reach neck design of 12"
(305 mm)
• Neck swivels easily, 360°
• Unique protective spout tip
prevents after drip
• Modular air gap (patent
pending)
• Base diameter is 2-1/4" (57 mm)
• Preinstalled tubing for quick connections
• Mounting hardware included
• NSF listed to ANSI NSF Std. 61-1999a
• Two-year warranty
The Tomlinson Contemporary RO Faucet comes in four
fabulous finishes which add high style to the high-end
kitchen.
Features:
• Elegant design complements
today’s high-end kitchens
• Retrofits most brands
• Lever style handle
• Protective spout tip design
prevents after-drip
• Patented modular air gap (US
patent #7,011,106)
• Internal ceramic disc provides
smooth operation
• High reach neck of 12" (305
mm); swivels easily, 360°
• Preinstalled tubing allows for
quick connections
• All mounting hardware is
included
• NSF listed to ANSI NSF Std. 61
• Two-year warranty
Specifications for Contemporary ROItem # Model Description87551 Designer Air Gap RO Faucet, Polished Chrome
87552 Designer Air Gap RO Faucet, Satin Nickel
87553 Designer Air Gap RO Faucet, Antique Bronze
87554 Designer Air Gap RO Faucet, Brushed Stainless Finish
Spout Reach: 5" (127 mm)Overall Height: 12" (305 mm)Pressure Rating: 125 PSI / 8.3 BARFlow Rate at 35 PSI / 2.32 BAR: 1.0 gpm (3.785 lpm)Temperature Rating: 40°F / 4°C to 150°F / 66°CMounting Hole Diameter: Without Air Gap: 1/2" min; 1-1/8” max
Air Gap: 7/8" min; 1-1/8” maxMax. Mounting Surface Thickness: Without Air Gap: 2-3/8”
With Air Gap: 1”
Item # Model Description87540 Designer Air Gap RO Faucet, Polished Chrome87541 Designer Air Gap RO Faucet, Satin Nickel87542 Designer Air Gap RO Faucet, White87543 Designer Air Gap RO Faucet, Biscuit87544 Designer Air Gap RO Faucet, Black87545 Designer Air Gap RO Faucet, Polished Brass87546 Designer Air Gap RO Faucet, Antique Bronze87547 Designer Air Gap RO Faucet, Bright Nickel87548 Designer Air Gap RO Faucet, Brushed Stainless Finish
Spout Reach: 5" (127 mm)Overall Height: 12" (305 mm)Pressure Rating: 125 PSI / 8.3 BARFlow Rate at 35 PSI / 2.32 BAR: 1.0 gpm (3.785 lpm)Temperature Rating: 40°F / 4°C to 150°F / 66°CMounting Hole Diameter: Without Air Gap: 1/2"
Air Gap: 7/8"Max. Mounting Surface Thickness: Without Air Gap: 2-3/8”
With Air Gap: 1”
Specifications for Designer RO
The Designer ROFaucet is NSF listed toANSI Std. 61-1999A.
The Contemporary ROFaucet is NSF listed toANSI Std. 61.
110 Hydrotech
Value Faucets
The Value Faucets are the best alternative to upgrade the existing basic faucets in your home. The Value
Faucets are a unique quarter turn faucet that comes in two designs and six different finishes. These faucets are
NSF approved and are lead-free.
Features:• Elegant design complements today’s high-end kitchens
• NSF listed to ANSI NSF Std. 61 and is lead free
• Retrofits most brands
• Internal ceramic disc provides smooth operation
• High Neck Design which swivels 360°
• Lever style quarter turn handle
• All mounting hardware is included
• Available in two designs, six different finishes
• Two-year warranty
Series 888 Specifications• Overall Height of 11.5" (292 mm)
• Swivels Easily, 360°
• Spout Reach: 5.7" (146 mm)
• Mounting Hole Diameter: ½" (12.5 mm)
• Base Diameter: 1.73" (44 mm)
• Connection*: ¼" compression nut fitting
• Operating pressure: 125 psi/8.3 bar
• Flow Rate: 1.0 gpm/3.785 lpm at 35 PSI/2.32 BAR
• Temperature Rating: 4°C/40°F to 70°C/158°F
Series 905 Specifications• Overall Height of 11.075" (281.32 mm)
• Swivels Easily, 360°
• Spout Reach: 4.75" (120 mm)
• Mounting Hole Diameter: ½" (12.5 mm)
• Base Diameter: 1.76 (44.8 mm)
• Connection*: ¼" compression nut fitting
• Operating pressure: 125 psi/8.3 bar
• Flow Rate: 1.0 gpm/3.785 lpm at 35 PSI/2.32 BAR
• Temperature Rating: 4°C/40°F to 70°C/158°F
These faucets are NSF 61approved and are lead-free.
Item # DescriptionSeries 888
87580 Faucet, Polished Chrome87581 Faucet, Brushed Nickel87584 Faucet, Black87585 Faucet, Satin Nickel87588 Faucet, Antique Brass87589 Faucet, Antique Wine
Item # DescriptionSeries 905
87582 Faucet, Polished Chrome87583 Faucet, Brushed Nickel87586 Faucet, Satin Nickel87587 Faucet, Oil Rubbed Bronze
* The standard faucets come with 1/4" compression nut fitting. The 3/8" quick connect faucetadapter fitting (#92407) can be purchased separately.
Colour Selection Ring PackItem #87591Colour Rings are available for
consumer use.
Colours included are:
Chrome Plated
Antique Brass
Antique Wine
Bright Black
Brushed Nickel
Oil Rubbed Bronze
Satin Nickel
Chrome Plated
111Hydrotech
Kemflo - Reverse Osmosis Booster Pumps
Item #92325
Nominal Maximum Flow Rate = 1.0 LPM (0.26 USGPM)
Maximum Pump Pressure = 758 kPa (110 PSI)
Maximum Inlet Pressure = 414 kPa (60 PSI)
Ambient Temperature Limits = 5 to 35°C (40 to 90°F)
Voltage = 24VDC
The Kemflo Reverse Osmosis Booster Pump can be used with
Hydrotech's 101 or 123 Series Reverse Osmosis systems from
9 to 75 GPD to provide increased pressure to the inlet of the
system for increased production and higher quality water. The
pump provides virtually noise free operation.
Pump comes complete with:• 120VAC to 24VDC Class 2 Transformer, UL Approved for the US and Canada
• Pressure Switch with 3/8" QC Fittings
• Pump inlet / outlet with ¼" QC Fittings
• Vibration Dampening Motor Mount
1 Year Limited Warranty against manufacturing defects
Aquatec Reverse Osmosis Demand Pumps
Item # 92341
Aquatec DDP 5800 Series Delivery/Demand Pump Package• complete with internal on/off pressure switch
• 115V/60 Hz
• Pressure regulated to approximately 60 psi at 1 GPM
• Pump inlet/outlet 3/8”
Key Operating Benefits:• .25 to 1.5 GPM (5 lpm) flow
• Up to 130 psi (9 bars) pressure
• Adjustable switch and bypass
settings
• Auto purging
• 7 year design life (estimated)
• Highly efficient
• Minimal pulsations
• Whisper quiet at lower flows
• Self priming
• Can run dry without damage
• Chemically resistant versions
1 Year Limited Warranty against
manufacturing defects
112 Hydrotech
Aquatec - Reverse Osmosis Booster Pumps
Aquatec booster pumps are available for reverse osmosis system installations on low pressure water supplies. A
booster pump raises and maintains the water pressure to the optimum level to ensure the highest rejection rate
and maximum production.
Distinguishing Features
Accessories
• Toughest, most durable pump on the market
• Adjustable maximum outlet psi (regardless of feed
pressure)
• Expels trapped air (no more air locks)
• Can be mounted w/pump head up or down
• More flow at extremely low inlet pressures
• New motor venting system to remove moisture
• EMI/RFI electronic noise suppression
• 100% final performance tested
• 1 year limited warranty against manufacturing
defects
Item #92319:
CDP 6800 Transformer
Item # 92318:
3/8” PSW Tank Shut-off Switch
Item #93323:
CDP 8800 Transformer
Item # 92317 Aquatec Model CDP 8800 Series Booster Pump Package• complete with PSW Shutoff Switch and 115V Transformer • suitable for R.O. Systems rated up to 120 GPD.
Item # 92317-1 Aquatec Model CDP 8800 Package with 3/8” x 1/4” Connectors and Tubing
Item # 92287 Aquatec Model CDP 6800 Series Booster Pump Package• complete with PSW Shutoff Switch and 115V Transformer • suitable for R.O. Systems rated up to 50 GPD
Key Operating Benefits:• Maximum Pump Pressure - 120 PSI (827 kPa)
• Maximum Inlet Pressure - 40 PSI (275 kPa)
• Used with membranes 9 to 50 GPD
• Up to 30,000+ operating hours (estimated)
• Can run dry without damage
• Self priming - 60” lift
• Low voltage (12-24V) motor for maximum
safety
• Corrosion resistant exterior
• Continuous or intermittent operation
• Supplied with 3/8” PSW Tank Shut-off switch
• Quiet - less than 45 DBA
• Pump inlet/outlet 1/4” QC
• Flexible mounting plate
Key Operating Benefits:• Maximum Pump Pressure - 120 PSI (827 kPa)
• Maximum Inlet Pressure - 40 PSI (275 kPa)
• Used with membranes 50 to 100 GPD
• Up to 15,000+ operating hours (estimated)
• Can run dry without damage
• Self-printing - 60” lift
• Low voltage (12-24V) motor for maximum
safety
• Corrosion resistant exterior
• Continuous or intermittent operation
• Supplied with 3/8” PSW tank shut-off switch
• Quiet - less than 52 DBA
• Pump inlet/outlet 3/8” QC
• Flexible mounting plate
CDP 6800 Dimensional Specifications
CDP 8800 Dimensional Specifications
113Hydrotech
Item #92313Features• Polypropylene construction
• Maximum Pressure = 100 psig
• Diameter: 9 3/4”, Height: 19 1/2”
RO-Pro - Reverse Osmosis Storage Tank
COMPONENT
Item #42600029Model RO-132 Features• 4.4 Gal Total Tank Volume
• Metal construction
• 1/4” NPT Stainless Steel Connection
• Diameter: 11”, Height: 13-3/4”
• Maximum Working Pressure = 100 psig
PAE - Reverse Osmosis Storage Tank
COMPONENT
RO-Pro Drawdown - with 7 psi pre-charge pressure
PAE RO-132 Drawdown - with 5 psi pre-charge
RO-Pro tanks are
manufactured by
Kemflo International
Co., Ltd. - Pingtong,
Taiwan
RO-123 tanks are
manufactured by PAE
Machinery Industrial
Co., Ltd. - Taichung,
Taiwan
114 Hydrotech
Reverse Osmosis Storage Tanks
For Commercial and Industrial Applications• 100% nonmetallic, seamless vessels will never chip, rust, dent or leak
• Removable air cell allows for easy service and sanitization, or
replacement as needed
• All materials used in construction are FDA-approved
• 125 psig maximum operating pressure; 120°F maximum operating
temperature
• Five-year warranty from the date of manufacture.
Model No. Capacity Height Diameter System Assembly Wt.(gal./liter) (in./cm.) (in./cm.) Connection (lbs./kg.)
ROmate 15 14.5 26 1/2 16 1” male 1555.1 67 41 NPT 6.8
ROmate 20 19.8 32 1/4 16 1” male 1975.2 82 41 NPT 8.6
ROmate 30 29.5 44 16 1” male 23112.1 112 41 NPT 10.5
ROmate 40 40.3 56 3/4 16 1” male 30153.1 144 41 NPT 13.6
ROmate 80 86.7 55 1/2 24 1/4 1 1/4” male 58329.5 141 62 NPT 26.4
Model No. PSI Precharge System Shutoff Pressure (gal./liter)30 40 50 60 70 80 90 100
ROmate1510 6.5 8.0 9.0 9.7 10.3 10.7 11.1 11.4
24.6 30.1 33.9 36.7 38.9 40.6 41.9 43.120 3.2 5.3 6.7 7.8 8.6 9.2 9.7 10.1
12.3 20.1 25.4 29.4 32.4 34.8 36.7 38.3
ROmate 2010 8.9 10.9 12.2 13.3 14.0 14.6 15.1 15.5
33.5 41.1 46.3 50.2 53.1 55.4 57.3 58.820 4.4 7.2 9.2 10.6 11.7 12.5 13.2 13.8
16.8 27.4 34.7 40.1 44.2 47.5 50.1 52.3
ROmate 3010 13.2 16.2 18.2 19.7 20.9 21.8 22.5 23.1
50.0 61.2 69.0 74.7 79.1 82.5 85.3 87.620 6.6 10.8 13.7 15.8 17.4 18.7 19.7 20.6
25.0 40.8 51.8 59.8 65.9 70.7 74.7 77.9
ROmate 4010 18.0 22.1 24.9 27.0 28.5 29.8 30.8 31.6
68.2 83.7 97.3 102.1 108.1 112.8 116.6 119.720 9.0 14.7 18.7 21.6 23.8 25.5 26.9 28.1
34.1 55.8 70.7 81.7 90.0 96.6 102.0 106.4
ROmate 8020 19.4 31.7 40.2 46.4 51.2 54.9 58.0 60.5
73.4 120.0 152.2175.7 193.7 207.9 219.4 228.930 X 15.9 26.8 34.8 40.9 45.8 49.7 52.9
X 60.0 101.4131.8 155.0 173.3 188.1 200.3
115Hydrotech
For each model from the RO-1 through the RO-14, the first line is the capacity in gallons with a 5 psig air charge. (0.34 bar);
the second line is the capacity in liters with a 0.34 bar air charge. For models RO-20 through RO-86, the air charge is 10
psig (0.69 bar).
AMTROL Reverse Osmosis Water Storage Tanks• The most reliable R.O. tank made - the choice for the first R.O. system ever
made...still first choice among R.O. makers today.
• Broadest line in the industry
• Meets the most demanding specifications for potable water - certified by NSF,
Standard 58. Meets U.S. FDA Spec 121.2500, Sub F.
• Keeps water tasting fresh
• Unsurpassed customer service, on time delivery and ready availability
• American made
• 5 year warranty
The Design That Has Set The StandardFifty years of innovation, quality control and
engineering excellence go into every AMTROL
tank.
• Longest lasting charge in the industry
• AMTROL’s pioneering diaphragm design provides:
longest life and most complete water discharge
• Fully enclosed polypropylene and butyl water
reservoir - ensures water purity and has less
rubber/water contact than a bladder tank
• Built to last - durable steel tank
• AMTROL is an ISO 9001 Company
Total Tank Water Capacity in Gallons (Liters) at Various System Pressures Dimensions Shipping
Model Volume psig 20 30 40 50 60 70 Diameter Height Weight
Number Gal. (Ltr) bar 1.38 2.07 2.76 3.45 4.14 4.83 cm (inches) cm (inches) kg (lbs)
RO-2 2.0 0.9 1.1 1.3 1.4 1.4 1.6 20.32 32.07 2.3
(7.6) (3.4) (4.2) (4.9) (5.3) (5.3) (6.0) (8") (12-5/8") (5)
RO-3 3.2 1.4 1.8 2.0 2.2 2.4 2.5 23.02 35.8 3.2
(12.1) (5.3) (6.8) (7.5) (8.4) (9.1) (9.5) (9-11/16") (14-3/32") (7)
RO-4 4.4 1.9 2.5 2.8 3.1 3.2 3.4 27.94 38.1 4.1
(16.7) (7.2) (9.5) (10.6) (11.7) (12.1) (12.8) (11") (15") (9)
RO-14 14.0 6.1 7.8 9.0 9.7 10.3 10.7 39.05 56.36 10.9
(53.0) (23.1) (29.5) (34.1) (36.9) (39.0) (40.5) (15-3/8") (22-3/16") (24)
RO-20 20.0 5.8 8.9 11.0 * * * 39.05 80.65 14.6
(75.7) (22.0) (33.7) (41.6) * * * (15-3/8") (31-3/4") (32)
RO-34 34.0 9.1 14.7 18.2 20.6 22.4 23.8 55.88 74.93 27.7
(128.7) (34.4) (55.6) (68.9) (78.1) (84.8) (90.1) (22") (29-1/2") (61)
RO-44 44.0 12.7 19.7 24.1 27.2 29.5 31.2 55.88 91.44 39.1
(166.6) (48.1) (74.6) (91.2) (103.0) (111.7) (118.0) (22") (29-1/2") (86)
RO-86 86.0 24.8 38.5 47.2 43.2 * * 66.04 119.86 55.8
(325.5) (93.9) (145.7) (178.7) (163.5) * * (26") (47-3/16") (123)
Reverse Osmosis Storage Tanks
116 Hydrotech
Aqua Flo Under Sink Filter Systems
Ultra 2 Under Sink Filter System• Ideal for home, farm or cottage use on
microbiologically safe water supplies.
• Filters sediment, rust and unpleasant tastes
and odors.
• Reduces levels of chlorine and sediment
down to 0.5 micron.
• Easy do-it-yourself installation.
• Includes attractive chrome plated faucet.
• Cheaper and more convenient than bottled
water.
Ultra 2 Under Sink Filter SystemNo. 26117
Replacement CartridgesNo. 26118
0.5 Micron Carbon Briquette Cartridge
No. 26006
Superior Taste Cartridge
Chrome Long Reach FaucetNo. 87511
117Hydrotech
Remote Water Chiller
Stylish and unique water chiller that fits discretely under the kitchen
sink...ready to plug in!
• Provides perfectly chilled drinking water at 39 - 42°F (4 - 6°C)
• All stainless steel waterways to use with RO system
• White powder coated galvanized steel cabinet with light gray plastic
fascia
• Easy to install with quick-connect fittings
• Four foot insulated power cord with NEMA 5-15 plug-ready to plug in
• Adjustable water temperature control
• One gallon per hour cooling capacity; stainless steel storage tank
• Air cooled; no cabinet venting required
• Includes four feet of 1/4” diameter tubing, two quick-connect fittings,
wall mounting clips and screws, instruction manual
• NSF approved
Cabinet: Powder coated galvanized steel cabinet with plastic front.
Cold Water Refrigeration Unit: Convection-cooled condenser. Internally spring mounted, hermetically sealed
compressor with automatic overload protector. No lubrication needed. Refrigerant is controlled accurately by
capillary tube. Air-cooled; designed to fit under a cabinet.
Cold Water Thermostat: Temperature is controlled by an adjustable thermostat with “OFF” position that is easily
accessible on the front of the cabinet.
Cold Water Reservoir: Evaporator is made of copper tube on stainless steel water tank and both are
encapsulated in insulation.
Capacity: 1 GPH cooling capacity.
Electrical: 115 volts, 60 Hz. Water cooler compressor hp 1/20. Insulated power cord with NEMA 5-15 polarized
plug.
Limited One Year Warranty: One year on the sealed refrigeration system and most component parts. Detailed
warranty certificate enclosed with each water cooler; sample copy available upon request.
Cooling 115 volts, 60Hz Dimensions NetItem Model Capacity1 Full Load Rated W x D x H Weight
Number Description GPH (LPH) Amps Watts Inches Lbs.
2878 R1P 1.0 (3.8) 1.3 135 10-5/16 x 8-3/4 x 14-5/8 30
(1)Capacity is at industry standard rating conditions of 50°F (10°C) outlet water, 80°F (26.7°C) inlet water and 90°F (32.2°C) ambient air.• Model covered by this specification complies with all known Plumbing Codes. Listed by Underwriters Laboratories Inc.• Components in this cooler are lead free as defined by the safe Drinking Water Act Amendments of 1986, and the Lead Contamination Control Act of 1988.• Drinking water cooler is Certified to NSF/ANSI 61.• All specifications subject to change without notice.
Specifications
Manufactured by Tri Palm International, LLC
Cienega De Flores, Mexico
Certified toNSF / ANSI 61 / Section 9
118 Hydrotech
Bottle-Free Point-of-Use Coolers
The PURA COOL is an economical
bottle-free cooler product.The
treatment system is mounted remotely
and the cooler provides hot and cold
filtered drinking water in a basic yet
sturdy platform.
Features• Hot and Cold dispensing spigots
• Hot water safety lock to prevent
accidental dispensing
• Dual float shut-off for safety
• Both remotely mounted filtration or
reverse osmosis options
• Meets UL and CSA requirements
The PURA MAX bottle-free cooler
is a product with a modern look and
feel suitable for business and
homes, but without the added
ultraviolet option of the Max Plus
model.
Features• Modern look with metallic finish
matches any décor particularly in
office environments
• 1 gallon stainless steel cold tank
• Hot and Cold dispensing spigots
• Hot water safety lock to prevent
accidental dispensing
• Lower cabinet is large enough to
mount either a filtration cartridge
package or a reverse osmosis
system
• Meets UL and CSA requirements
The PURA MAX PLUS includes a
system which re-circulates water from
the cold reservoir past an ultraviolet
sterilization lamp for continual
sanitization. This Max Plus has a
modern look and feel that is suitable
for both business and home
environments.
Features• Modern look with metallic finish
matches any décor particularly in
office environments
• Re-circulating ultraviolet sanitization
provides peace of mind
• 1 gallon stainless steel cold tank
• Hot and Cold dispensing spigots
• Hot water safety lock to prevent
accidental dispensing
• Lower cabinet is large enough to mount either a
filtration cartridge package or a reverse osmosis
system
• Meets UL and CSA requirements
With advanced features such as
“in tank” UV Sanitization and
BioCote® to inhibit biological
growth, the PURA ULTIMATE
provides an endless supply of
water with safety and security. The
Ultimate modern and yet robust
appeal and function is perfect for
installation in all applications.
Features• Three water temperature settings
meets everyone’s needs
• In tank ultraviolet sanitization
lamp maintains water quality in
the cold tank
• Lower cabinet mounts either
filtration or reverse osmosis
equipment
• BioCote® Technology protects from bacterial
growth on exterior
• Leak detection and automatic shut-off prevent
water damage
• Large 1 gallon cold tank
• 9” high filling height for pitchers
• Adjustable levelling feet
119Hydrotech
Bottle-Free Point-of-Use Coolers
Model Cold Tank Capacity Hot Tank Capacity Electrical Dimensions Water Dispensing Areausgal (L) usgal (L) H x W x D inches (mm) Connection Height inches (mm)
PURA Cool 1.2 (4.5) 0.9 (3.5) 120V/60Hz/6.2A 39x12x12 (980x312x314) 1/4” tube 7.75 (197)PURA Max 0.9 (3.5) 0.4 (1.5) 120V/60Hz/4.7A 42x13x15 (1060x330x380) 1/4” tube 7.5 (190)
PURA Max Plus 0.9 (3.5) 0.4 (1.5) 120V/60Hz/4.7A 42x13x15 (1060x330x380) 1/4” tube 7.5 (190)PURA Ultimate 1.2 (4.5) 0.4 (1.5) 120V/60Hz/6.2A 46x16x15 (1160x410x380) 1/4” tube 9.0 (228)
Model Removable Cold Hot Room Temp. Reserve Storage Leak UV BioCote NSF Filtration ReverseDrip Tray Water Water Water Tank usgal (L) Detection Protection 61 Osmosis
PURA Cool � � � — — — — — — Remote RemotePURA Max � � � — — � — — — � �
PURA Max Plus � � � — — � � — — � �PURA Ultimate � � � � 3 (11) � � � � � �
Municipal/ Chlorinated/ pH Maximum Turbidity Maximum Hardness Iron Manganese Hydrogen ResidualPrivate Non-Chlorinated Range TDS SDI (Fe) (Mn) Sulphide (H2S) Chlorine (Cl)
Filtration both both 3.0-11.0 <500 mg/L <1.0 NTU — <350 mg/L <0.1 mg/L <0.05 mg/L <0.0 mg/L <0.0 mg/LEquipped Coolers recommended (<20gpg)Reverse Osmosis both both 3.0-11.0 <500 mg/L <1.0 NTU <4.0 <350 mg/L <0.1 mg/L <0.05 mg/L <2.0 mg/L <2.0 mg/LEquipped Coolers recommended (<20gpg)
Specifications
Source Water Supply Profile
Electrical: 120V/60Hz Grounded North American electrical outletInlet Water Pressure: 40 - 60 psi (275-414 kPa) Recommended / 100 psi (862 kPa) MaximumInlet Water Temperature: 40 - 100°F (4 - 38°C)Drain Connection: Required for coolers equipped with reverse osmosis
PURA Point-of-Use Coolers producebottle quality water.
• UV Light - Without harmful chemicals, ultraviolet light
sanitizes water to protect you from bacteria.
• BioCote® - A new technology offering antimicrobial
protection against the fungi, mold, and bacteria to
reduce unpleasant odors.
• Activated Carbon Filtering - reduces chlorine taste and odor.
• Sediment Filtering - reduces turbidity and sediments.
• Reverse Osmosis - WaterGroup’s 1240 Series reverse osmosis
technology reduces total dissolved solids in the water.
120 Hydrotech
Leak Controller
The first line of defense against water damage.Leak Controller detects the water spill on the surface and engages a shut-off valve
to cut-off the water supply. It also sounds an alarm to alert the customer until the
valve is manually reset. By preventing the continuous water flow, equipment and
property damage are restricted and the user liability is reduced.
It can be connected to the water purification system, POU coolers, refrigerators, ice
makers etc.
Features• Available valve to tubing connection sizes: 1/4” for plastic and copper tubing
• LeakLogic™ RISC based management - state of the art microchip technology forsensitive controls, operation verification and long battery life
• Status test button
• Audio and LED status indicator
• Audio alarm
• Powered by 4 “AA” batteries - no external electrical connections required• Pull-out battery holder for convenient battery replacement
• Programmable service reminder
• NSF approved automatic ball valve shut-off and plastic tubing
• Two screw mounting plate allows for quick and simple installation
• Sensor towel
• Built with superior impact resistant ABS plastic
• One sensor included with coin test slot and series connectors
• Built with reinforced nylon and glass materials on stressed components
• Water detection sensitivity down to 2 ppm TDS (Total Dissolved Solids)
• Programmable service reminder indicator
• Conformal coating on the printed circuit board
• One Year Limited Warranty from date of purchase against defects in material and workmanship
Power 4 “AA” size alkaline type batteriesSensor Electromechanical dual probe with series connectorsTemperature System operating range: 40° to 100°F (4° to 37°C)
Water operating range: 36° to 140°F (2° to 60°C)Size (H x W x D) 6.75 x 3.25 x 2.5” (171 x 83 x 64 mm)Weight 0.9 lbs (0.4 kg) with batteriesSolenoid 6V DC Push-TypeAlarm 85+dB at 5’ @ 3.4 ± 0.5 kHz pulsing alarmLED BlueMounting Accessories and bracket supplied for wall mountingBattery Replacement Replace annually or upon low battery indicator
- This product does not guarantee the prevention of water damage.- Many factors increase the probability of preventing water damage including: Constant Leak Controller testing / Physical
verification of all parts / Correct placement of the sensor(s)
Specifications
Manufactured by Water Controller Products
Livermore, California
Item #92434
121Hydrotech
John Guest PI Range Quick Connect Fittings
John Guest PI Range of quick connect fittings are
now available for your fluid connection needs. The PI
Range of inch-size push-in fittings is offered for tube
sizes 5/32" O.D. to 5/8" O.D. The fittings are
manufactured in gray acetal copolymer with food
grade nitrile ‘o’ ring, making them especially suitable
for applications involving foodstuff and potable liquids.
They are equally suitable for air and inert gasses and
can therefore be used on CO2 lines, pneumatic
applications, and vacuum.
Most John Guest fittings come in packages of ten.
Consult the attached list of the John Guest fittings
currently available and package details.
Please contact customer service for current pricing and stock status.
Notes
122 Hydrotech