DUET manual Ver.1 Rev 5 11/2016 1 DUET SHOWER DOOR/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine ® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com For more information about DreamLine ® products please visit DreamLine.com Model#: SHDR-1248728-## SHDR-1260728-## Model#: SHDR-1260588-## ## = finish: 01- Chrome / 04-Brushed Nickel
17
Embed
DreamLine Showers : DreamLine Duet Shower Door & Tub Door ... · DUET manual Ver.1 Rev 15 11/2016 DUET SHOWER DOOR/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
DUET manual Ver.1 Rev 5 11/2016 1
DUET
SHOWER DOOR/TUB DOOR INSTALLATION INSTRUCTIONS
IMPORTANT
DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice.
For the latest up-to-date technical drawings, manuals, warranty information or additional details
please refer to your model’s web page on DreamLine.com
4. Push the Glass Profiles (#03) all the way over the Wall Profiles (#02). Make sure the Wall Profile flange faces inside the shower.
See Fig. 5 and Fig. 6 for details.
1
2
inside
Fig. 4
Fig. 5
DUET manual Ver.1 Rev 5 11/2016 9
5. Move the assembled frame to the designated
position and adjust the Wall profiles (#02) so that
they are tight to the walls by slightly pulling them
out of the Glass Profiles (#03) if necessary.
NOTE: Use a level to check the wall profiles for
plumb and vertical while marking the holes for
drilling.
See Fig. 7 for details.
Fig. 6
Fig. 7
DUET manual Ver.1 Rev 5 11/2016 10
6. Hold the frame in the correct position, mark the
drill holes on the wall through the holes on the
flange of the Wall Profile (#02).
Set the assembled unit aside; drill the holes in the
wall using a Ø5/16” drill bit and insert the Wall
anchors (#07).
See Fig. 8 for details.
7. Apply silicone to the back of the wall profiles, into the drilled holes and to the bottom of the bottom guide rail prior to attaching to the opening. Place the frame back into position and secure it to the walls using Truss Head ST4.2 x 40 screws (#09). Use a level to re-check the wall profiles for plumb before fully tightening the wall screws.
See Fig. 9 for details.
4
3
2
1
Ø 5/16”
1
2
inside
outside
inside
Fig. 8
Fig. 9
DUET manual Ver.1 Rev 5 11/2016 11
8. Secure the Rollers (#11) to the top of the
Glass door (#05). Mind the direction of the
rollers. (See Fig 10.1 and Figs 11- 13)
Attach the Handle brackets (#12) to the
Glass doors (A & B) using the 25mm
machine head screws (screw bag #12).
The handle brackets should face the same
direction as the roller wheels. Then secure
the Handles (#06) to the Handle brackets
using Round head screw ST4.2×25 (screw
bag #12) and cover the holes with the
decorative bracket covers provided. (Fig
10.4)
See Fig. 10 for details.
PLEASE NOTE:
On the outside of Glass door (A) the Handle and the Rollers
should face out.
On the inside of Glass door (B) the Handle and the Rollers
should face inside.
See Fig. 11 and Fig. 12 for details.
A
4
3
2
1
Fig. 10
Fig. 11
DUET manual Ver.1 Rev 5 11/2016 12
9. From inside of the shower, install the outside Glass door (A) (#05) first, as shown in Fig 13.1 and
13.2. Then install the inside Glass door (B) (#05) making sure that the rollers are aligned in the
Upper guide rail (#01) as shown. See Fig. 13 and Fig. 14 for details.
A B
B
3
2 4
1
inside outside
Fig. 12
Fig. 13
DUET manual Ver.1 Rev 5 11/2016 13
10. From inside the shower, slide both Glass Doors
(#01) to the right. Place the Left guide block
(#13) to the end of the guide rail and mark the
drill hole in the Bottom Guide rail (#04) through
the pre-drilled hole on the block using an Ø1/8”
drill bit. Drill the hole and secure the Guide block
with the Pan Head screw ST4.2×16 (08) using
the washers and the Decorative Covers (10).
See fig. 15 for details.
Repeat Step #10 to install the Middle guide
block and the Right guide block to the Bottom
Guide rail (#04).
See Fig. 15 for details.
3 1/2"
Ø 1/8”
3
2
4
5
1
Fig. 15
Fig. 14
DUET manual Ver.1 Rev 5 11/2016 14
11. Fasten the Rubber stopper (#14) inside the groove of the Wall
Profile (#02) using the Pan Head screw ST4.2×16 (#08).
Repeat for all 6 of the Rubber stoppers (#14).
See Fig. 16 for details.
12. Perform final adjustments of the Wall Profiles
(#02) on the assembled unit making sure that
the bottom rail is tight to the threshold. Drill
Ø1/8" holes through the Glass profiles (#03)
into the Wall profiles (#02) as shown in Fig 18.1
and attach them together using the Pan Head
ST4.2 x 16 screws (#08) along with the
decorative cover and washer. (#10).
See Fig. 17 for details.
1
2
2
1 Ø 1/8”
Fig. 17
Fig. 16
DUET manual Ver.1 Rev 5 11/2016 15
13. After final adjustments of the Glass doors (#05),
install the small black Pin Blocker that is
packaged with the Rollers (#11).
Insert the Pin Blockers all the way into the
pre-drilled holes on the body of the Roller from
the screw side as shown. This pin will prevent the
doors from being lifted of the track,
See Fig. 18 for details.
14. From inside of the shower, apply a good quality mildew-resistant silicone along the profiles and
the guide rails; on the seams between the bottom guide rail and the vertical profiles as well as
along the shower base or threshold. You may also apply silicone from the outside if you choose.
See Fig. 19 for details.
caulk
caulk
Fig. 18
Fig. 19
DUET manual Ver.1 Rev 5 11/2016 16
Product Maintenance
BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls:
wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-
abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners.
Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the
surface.
GLASS: To ensure long lasting life for your glass shower products: wipe them off
after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth
or a squeegee to prevent soap buildup and water spots (Hard water can etch the
surface of the glass over time if left to dry). To prevent scratching the surface: never
use abrasive cleaners or cleaning products that contain scouring agents. Never use
bristle brushes or abrasive sponges that may scratch the surface.
HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use
with a soft cloth. Do not use abrasive cleaners or cleaning products containing
ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to
prevent damage to the finish (peeling or corrosion). After cleaning the polished
finishes, rinse thoroughly and wipe dry with soft cloth.
Clean stainless steel surfaces at least once a week. When applying stainless steel
cleaner or polish to stainless steel hardware, work with (not across) the grain. Never
use an abrasive sponge or cloth, steel wool or wired brush as these may permanently
scratch the surfaces.
NOTE: To maximize the life of your door, it is important to regularly
inspect the glass and all hardware for misalignment, proper attachment,
and/or damage. Contact DreamLine with any questions or concerns.
TEL: 866-731-2244
FAX: 866-857-3638
DREAMLINE.COM
For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com