DOWNHOLE OIL TOOLS - · PDF fileDOWNHOLE OIL TOOLS. ii ... We invite you to contact our downhole tools team to learn how we can bring a world of re- ... Motor

• Well Completion Tools• Coiled Tubing Tools• Flow Control Tools

D OW N H O L E O I L TO O L S

ii

INTRODUCTION

World-class, state-of-the-art precision. A robust and comprehensive engineering staff. In-house control over all and phases of production and superior products and support. That’s what you get with SERVA SJS downhole tools.

SERVA SJS downhole tools are designed to perform in demanding high-temperature and high-pressure (HTHP) applications in all climates and geographies. With resources like our own rubber shop and indoor test well, we offer unparalleled capabilities to develop and optimize tools to your specific requirements.

Founded in 1992, and located in the heart of China’s Hubei province, SERVA SJS supports oil- and gasfield customers around the globe the equipment, tools and services to deliver downhole success. Extensive engineering, design and production resources make SERVA SJS the first choice for packers, bridge plugs, cement retainers, flow control downhole tools, coil tubing downhole tools and all related accessories, with API 11D1 and ISO 9001 certifica-tions.

We invite you to contact our downhole tools team to learn how we can bring a world of re-sources to your operation to achieve greater success.

SERVA

Well served.™

A WO R L D O F R ES O U R CES F O R D OW N H O L E S U CCESS

1

Material Selection

SERVA SJS’s equipment is offered in various material configurations for a variety of well con-ditions. The following alloys and groups of alloys are currently the most common materials used for the construction of packers and related equipment:

• Standard, non‐corrosive service -Low alloy steels(e.g., 4140 or Chinese 42CrMo) with mechanical properties compatible with API P110 tubulars.

• Non‐corrosive service containing H2S -Low alloy steels (e.g., 4140 or Chinese 42CrMo) with mechanical properties compatible with API L80 tubulars.

• Corrosive CO2 service with little or no H2S -Martensitic and PH stainless steels(e.g., 9Cr, 13Cr, 17-4PH) with mechanical properties that vary from 80 ksi to 110 ksi minimum yield strength. The selection of the specific corrosion resistant alloy depends on the environment (pH, chlorides, temperature, H2S, etc,) and strength requirements.

• Severely corrosive CO2 and H2S -Nickel alloys such as 718 at strength level of 110 ksi minimum yield strength and higher.

For equipment required to perform a temporary function and then allowing quick removal by drilling or milling, an additional group of materials are used:

• Cast iron• Reinforced polymer based composites

2

TABLE OF CONTENTS

Well Completion Tools

Bridge Plugs

STWB Wireline Set Bridge Plug ................................................................... 8

SCP Composite Bridge Plug ........................................................................ 9

STMB Mechanical Bridge Plug .................................................................. 10

SWRB Wide Range Bridge Plug ................................................................. 11

SHMB Hydro-Mech Set Bridge Plugs ......................................................... 12

SRWB Wireline Set Bridge Plugs (Retrievable) ........................................... 13

Cement Retainers

STWR Wireline Set Cement Retainer .......................................................... 14

STMR Mechanical Cement Retainer ........................................................... 15

Stinger Seal Assemblies

STSS Stinger Seal Assembly ..................................................................... 16

Setting Tools

Wireline Setting Tools .............................................................................. 17

Hydraulic Setting Tools ............................................................................ 18

STSB Mechanical Setting Tool .................................................................. 19

STSR Mechanical Setting Tool ................................................................... 20

Tubing Centralizer

STTC Tubing Centralizer ............................................................................ 21

Permanent Production Packers

SPP-C Permanent Production Packers ....................................................... 22

SPP-XC Permanent Production Packers ..................................................... 23

SQS Hydro-Set Retainer Production Packers .............................................. 24

SPP-R Retrievable Production Packers ...................................................... 25

Mechanical Setting Packers

SMR-D Double Grip Retrievable Packer ..................................................... 26

SMR-D Large Bore Double Grip Retrievable Packer..................................... 27

SMR-S Single Grip Retrievable Packer ....................................................... 28

SMA Mechanical Set Retrievable Production Packers ................................. 29

3

STLS Mechanical Set Retrievable Production Packer .................................30

SMJ-A Mechanical Set Retrievable Production Packers ..............................31

SMJ-B Mechanical Set Retrievable Production Packers ..............................32

SMJ-C Retrievable Storm Packer ..............................................................33

SMJ-D Retrievable Packer ........................................................................34

SMC Retrievable Packers .........................................................................35

SME Packer (Y221)..................................................................................36

SMT Tension Packers ..............................................................................37

SMP Pull-Push Type Packer .....................................................................38

Hydraulic Setting Packers

SH-2 Hydraulic Setting Packers ...............................................................39

SHF Retrievable Double-Grip Hydrostatic Single-string Packer ..................40

SHC Packer (Y341) ..................................................................................41

SHH Packer (Y344) ..................................................................................42

Tubing Anchor

STA Tubing Anchor ..................................................................................43

Others

SEJ Expansion Joint .................................................................................44

SSV-2 Storm Valve ..................................................................................45

SAH Hydraulic Anchor & SCV Circulation Valve .........................................46

SSJ Safety Joint & Pump Out Plug ............................................................47

Dump Bailer ...........................................................................................48

“C” Type Sur-Grip Vise ............................................................................49

4

TABLE OF CONTENTS

Coiled Tubing Tools

‘Torconnect’ External Slip Coil Connector .................................................. 50

‘Slimconnect’ External Slip Connector ...................................................... 51

‘Torconnect’ Internal Slip Connector ......................................................... 52

Roll-On Connector ................................................................................... 53

Double Ended Roll-On Connector .............................................................. 54

Dimple/Grub screw Connector ................................................................. 55

Pull Plate for Coil Connector ..................................................................... 56

Dual Flapper Check Valve ......................................................................... 57

Twin Flapper Check Valve with Lock-Out Sleeve ......................................... 58

Ball Check Valve ...................................................................................... 59

Heavy Duty Hydraulic Disconnect ............................................................. 60

Shear Release Joint .................................................................................. 61

Dual Activated Circulation Valve (Drop Ball/Over Pressure) ........................ 62

Burst Disc Circulation Sub ........................................................................ 63

Straight Bar ............................................................................................. 64

Down-Stroke Intensifier ........................................................................... 65

Up-Stroke Intensifier ................................................................................ 66

Down-Stroke Hydraulic Jar ........................................................................ 67

Up-Stroke Hydraulic Jar ............................................................................ 68

Roto-Hammer Impact Drill Jar ................................................................... 69

Hydraulic Up/Down Jars ........................................................................... 70

Hydraulic Up/Down Intensifiers ................................................................ 71

Fluted Centralizer .................................................................................... 72

Bow Spring Centralizer ............................................................................ 73

Flow Activated Bow Spring Centralizer ...................................................... 74

Torque Thru Knuckle Joint ......................................................................... 75

C.A.R.S.A.C ‘HT’ Connector ....................................................................... 76

Swivel Joint ............................................................................................. 77

Locking Swivel Joint ................................................................................. 78

Motorhead Assembly ............................................................................... 79

Motor ...................................................................................................... 80

5

GS’ Running/Pulling Tools .......................................................................81

“JDC”Running/Pulling Tools ....................................................................82

Flow Activated Shifting Tools ...................................................................83

Double Ended Selective Shifting Tools .....................................................84

Tubing Anchors.......................................................................................85

Tubing Cutter ..........................................................................................86

Mills ......................................................................................................87

Rotary Jet Wash Tools ..............................................................................88

Spinning Wash tool ................................................................................89

Flow Activated Hydraulic Jetting Indexing Tools ........................................90

Nozzle Options .......................................................................................91

Flow Activated Releasable Fishing/Bulldog Spears ...................................92

Flow Activated Releasable Overshots .......................................................93

Rope Spear ............................................................................................94

Fishing Grabs .........................................................................................95

Venturi Junk Baskets ...............................................................................96

Lead Impression Blocks & High Powered Magnet .....................................97

Tubing Nipple Locators ...........................................................................98

Collar Stop .............................................................................................99

6

TABLE OF CONTENTS

Flow Control Tools

X Profile Nipple...................................................................................... 100

XN Profile Nipple ................................................................................... 101

F Profile Nipple ...................................................................................... 102

R Profile Nipple ..................................................................................... 103

XO/XD Circulating Sleeve ....................................................................... 104

XA Circulating Sleeve ............................................................................. 105

T-2 On-Off Tool ...................................................................................... 106

PX & PXN Plug ....................................................................................... 107

X & XN Lock Mandrel PX / PXN Equalizing Prong and Valve ....................... 108

FWG By-Pass Blanking Plug .................................................................... 109

RZG By-Pass Blanking Plug .................................................................... 110

FWB Down Instrument Hanger ................................................................ 111

RZB Down Instrument Hanger ................................................................. 112

FB-2 Equalizing Check Valve ................................................................... 113

RB-2 Equalizing Check Valve .................................................................. 114

B Shifting Tool ....................................................................................... 115

X-Line Running Tool ............................................................................... 116

C-1 Running Tool .................................................................................... 117

SB Series Pulling Tool ............................................................................ 118

JD Series Pulling Tool ............................................................................. 119

GS Running/Pulling Tool ........................................................................ 120

GR Adapter ............................................................................................ 121

B Probe ................................................................................................. 122

F Collar Stop .......................................................................................... 123

Tubing End Locator ................................................................................ 124

Single Strand Rope Socket ..................................................................... 125

Brass Wedge Rope Socket ...................................................................... 126

MS Rope Socket..................................................................................... 127

Wireline Stem ........................................................................................ 128

Wireline Roller Stem .............................................................................. 129

Knuckle Joint ......................................................................................... 130

Knuckle Jar ............................................................................................ 131

7

Tubular Jar ............................................................................................132

Link/Spang Jar .....................................................................................133

Wireline Intensifier ...............................................................................134

Wireline Shock Absorber .......................................................................135

Paraffin Cutter (Gauge Ring) ..................................................................136

Wireline Blind Box ................................................................................137

Pineapple Broach .................................................................................138

Tubing Swedge .....................................................................................139

Wireline Fluted Centralizer ....................................................................140

Bow Spring Centralizer .........................................................................141

Two Piece Sand Bailer ...........................................................................142

Dump Bailer .........................................................................................143

Go Devil ...............................................................................................144

Wirefinder Split Skirt ............................................................................145

Center Spear ........................................................................................146

Two Prong Wireline Grab .......................................................................147

“Baiting” Type Bulldog Spear ................................................................148

Releasable Overshot .............................................................................149

Heavy Duty Magnet Fishing Tool ............................................................150

Impression Block ..................................................................................151

PX Plug & FWG/RZG Plug Series Tools ....................................................152

8

WELL COMPLETION TOOLS

SPECIFICATIONS

Part Number

Casing OD

Casing Wt Setting RangeSet-ting Tool Setting kits

Tool OD Release Force

(in) (lbs/ft) Min (in) Max (in) (in) (lbs)

D22-0237-008 2 3/8 4.0-5.8 1.78 2.074

# 5

/ 1.75

9,000D22-0287-008 2 7/8 6.4-6.5 2.34 2.525 / 2.22

D22-0352-008 3 1/2 5.7-10.3 2.867 3.258 D22-0351-100 2.75

D22-0350-008 3 1/2 12.8-15.8 2.548 2.764 / 2.43 13,000

D22-0400-008 4 5.6-14 3.34 3.732# 10

D22-0400-100 3.14 20,000

D22-0450-008 4 1/2 9.5-16.6 3.826 4.09 D22-0450-100 3.59

33,000D22-0500-008 5 11.5-20.8 4.154 4.56

# 20

D22-0500-100 3.93

D22-0550-008 5 1/2 13-23 4.58 5.044 D22-0550-100 4.31

D22-0575-008 5 3/4 14-25.2 4.89 5.29 D22-0575-100 4.7

D22-0662-008 6 5/8 17-32 5.595 6.135 D22-0662-100 5.37

50,000

D22-0700-008 7 23-35 5.938 6.336 D22-0700-110 5.68

D22-0701-008 7 17-23 6.336 6.538 D22-0701-110 6.00

D22-0762-008 7 5/8 20-39 6.625 7.125 D22-0762-100 6.31

D22-0862-008 8 5/8 24-49 7.31 8.097 D22-0862-100 7.12

D22-0962-008 9 5/8 29.3-58.5 8.435 9.063 D22-0962-100 8.12

D22-1075-008 10 3/4 32.7-60.7 9.66 10.192 D22-1075-100 9.43

D22-1176-008 11 3/4 38-60 10.772 11.15 D22-1176-100 10.43

D22-1175-008 11 3/4 60-83 10.192 10.772 D22-1175-100 9.94

D22-1337-008 13 3/8 48-84.5 12.175 12.715 D22-1337-100 11.88

D22-1600-008 16 65-118 14.576 15.25 D22-1600-100 14.12

D22-2000-008 20 94-133 18.73 19.124 D22-2000-100 18.37

Model STWB Wireline Set Bridge Plugs are compact, small OD and designed for easy drill out. These bridge plugs will set securely in all but the very highest tensile casing. A ratchet lock ring stores the setting force in the plug. The one piece packing element and metal back up rings combine for a superior seal. The case hardened, one piece slips virtually eliminate premature setting, yet can be easily drilled out. They are available for 2 3/8” through 20” casing.

Features:

n Can be set directly with Baker wireline setting tools

n Easy for mill out

n Ratchet lock rings secure dynamic setting force

n One piece packing element and rocker action metal back up rings combine for a superior seal

n Shear studs are Baker style and connect directly to the Baker Adjuster Sub

n These bridge plugs can be run directly on Baker Setting Sleeves and Adjuster Subs

n Crossovers arenot required

ST W B W I R E L I N E SE T B R I D G E P LU G

9

S C P CO M P OS I T E B R I D G E P LU G

Model SCP Composite Bridge Plugs are used for temporary or permanent isolation of oil, gas and water, such as zone isolation, formation fracturing, acidizing. These easy drillable bridge plug can be use for multi zone fracturing especially, so it will be a good choice for shale gas exploration.

SCP-P Solid body

SCP-F No-solid body

SCP-D No-solid body, cage type

Features:

n Can be set directly with SWSG/SWSB wireline or SHSG/SHSB hydraulic setting tool

n Easy for mill out

n Slope bottom can stop the rotation of the bridge plug

n The working temperature is below 150°C(300°F)

SPECIFICATIONS

Part number Model Size Casing Wt

Dimension Setting range Release force

Pres-sure

TempOD ID Length Min Max

inch inch inch inch inch lbs PSI °F

D125082300SCP-P (Solid body)

5” 11.5~21 3.92 0.75 24.98 4.120 4.560 36,000 10k 300

D125582300 5 1/2” 15.5~23 4.36 - 32.38 4.670 4.950 33,000 10k 300

D127082300 7” 23~35 5.63 - 35 5.938 6.366 55,000 10k 300

D144082300

SCP-F(No-solid body, ball type)

4” 5.6~14 3.19 0.75 26.33 3.320 3.548 26,000 10k 300

D144582300 4 1/2” 9.5~15.1 3.61 0.75 22.68 3.826 4.090 26,000 10k 300

D145082300 5” 11.5~21 3.92 0.75 24.98 4.120 4.560 26,000 10k 300

D145582303 5 1/2” 15.5~23 4.36 1 30.23 4.670 4.950 33,000 10k 300

D147082300 7” 23~38 5.63 1.5 38.53 5.920 6.366 55,000 10k 300

D145082301 SCP-D(cage type)

5” 11.5~21 3.92 0.75 26.76 4.120 4.560 35,000 10k 300

D145582301 5 1/2” 15.5~23 4.36 1 30.23 4.670 4.950 33,000 10k 300

10


ST M B M EC H A N I C A L B R I D G E P LU G

SPECIFICATIONS

Part Number

Casing OD

Casing Wt Setting Range Tool ODRelease Force Setting Tool


D22-0450-009 4 1/2 9.5-16.6 3.826 4.09 3.59

33,000

D22-0450-004D22-0500-009 5 11.5-20.8 4.156 4.56 3.93

D22-0550-009 5 1/2 13-23 4.58 5.044 4.31 D22-0550-004

D22-0575-009 5 3/4 14-26 4.89 5.29 4.7 D22-0575-004

D22-0662-009 6 5/8 17-32 5.595 6.135 5.37

50,000

D22-0662-004

D22-0700-009 7 17-35 6.004 6.538 5.68 D22-0700-004

D22-0762-009 7 5/8 20-39 6.625 7.125 6.31 D22-0762-004

D22-0862-009 8 5/8 24-49 7.511 8.097 7.12 D22-0862-004

D22-0962-009 9 5/8 29.3-58.4 8.435 9.063 8.12 D22-0962-004

D22-1075-009 10 3/4 32.75-60.7 9.66 10.192 9.43 D22-1075-004

D22-1176-009 11 3/4 38-60 10.772 11.15 10.43 D22-1176-004

D22-1175-009 11 3/4 60-83 10.192 10.772 9.94 D22-1175-004

D22-1337-009 13 3/8 48-80.7 12.175 12.715 11.88 D22-1337-004

D22-1600-009 16 65-118 14.576 15.25 14.12 D22-1600-004

Model STMB Mechanical Bridge Plugs are used to isolate zones for temporary or permanent abandonment. These drillable bridge plugs set securely in any hardness casing. A ratchet lock ring stores the setting force in the bridge plug. The one piece pack¬ing element and metal back up rings combine for a superior seal. The case hardened, one piece slips virtually eliminate premature setting, yet can be easily drilled out. They are available for 4 1/2” through 16” casing.

Features:

n Sets securely in most casing, including many premium grades



n Compact, easy running

n Pressure balanced sleeve valve is opened and closed by tubing manipulation from the surface for better control

n Set with Model STSB Mechanical Setting Tool

n These bridge plugs can be set on any standard baker style mechanical setting tool

11

SW R B W I D E R A N G E B R I D G E P LU G

Wide Range Wireline Set Bridge Plugs are specially designed to run through tubing or restricted pipe and set securely in larger tubing or casing below. These bridge plugs will set securely in any hardness casing. A ratchet lock ring stores the setting force in the plug. The three piece packing element and metal back up rings combine for a superior seal. The case hardened, one piece slips virtually eliminate premature setting, yet can be easily drilled out. They are available for 1.610” through 5.044” setting range.

Features:

n Sets securely in any hardness casing, including premium grades


n Three piece packing element and rocker action metal back up rings combine for a superior seal


n Can be set either with GO, Baker or Gearhart wireline setting tools

SPECIFICATIONS

Part NumberSetting Range Tool OD Release Force

Min (in) Max (in) (in) (lbs)

D16-0237-001 1.610” 1.995” 1.468” 8,000

D16-0238-001 1.905” 2.441” 1.750”

12,000D16-0239-001 2.156” 2.765” 1.906”

D16-0350-001 2.375” 3.000” 2.187”

D16-0351-001 2.441” 3.343” 2.281”

D16-0400-001 2.875” 3.500” 2.500”25,000

D16-0401-001 3.187” 3.920” 2.750”

D16-0450-001 3.920” 4.276” 3.250”

30,000D16-0500-402 3.696” 4.276” 3.500”

D16-0550-001 4.154” 5.044” 4.062”

12


SPECIFICATIONS

Part number

Casing OD

Casing Wt Setting rangeTool OD

PressureRelease force Connection thread

(in) (lbs/ft) Max(in) Min(in) (in) (PSI) (lbs)

D22-0450-303 4 1/2 9.5-16.6 3.826 3.59 3.59

10,000

33,000 2 3/8”EUE BOXD22-0500-303 5 11.5-20.8 4.154 3.93 3.93

D22-0550-303 5 1/2 13-23 4.58 4.31 4.31

D22-0575-303 5 3/4 14-25.2 4.89 4.7 4.7

D22-0662-303 6 5/8 17-32 5.595 5.37 5.37

50,000

2 7/8”EUE BOX

D22-0700-303 7 23-35 5.938 5.68 5.68

D22-0701-303 7 17-23 6.336 6.00 6.00

D22-0762-303 7 5/8 20-39 6.625 6.31 6.31

D22-0862-303 8 5/8 24-49 7.31 7.12 7.12

D22-0962-303 9 5/8 29.3-58.5 8.435 8.12 8.12 8,000

3 1/2”IF BOXD22-1075-303 10 3/4 32.7-60.7 9.66 9.43 9.43 5,000

D22-1176-303 11 3/4 38-60 10.772 10.43 10.43 4,000

D22-1337-303 13 3/8 48-84.5 12.175 11.88 11.88 3,000

4 1/2”IF BOXD22-1600-303 16 65-118 14.576 14.12 14.121,500

D22-2000-303 20 94-133 18.73 18.37 18.37

S H M B H Y D R O-M EC H SE T B R I D G E P LU G S

Model SHMB Hydro-Mech Set Bridge Plugs are used for temporary or permanent isolation of oil, gas and water, such as zone isolation, formation fracturing, acidizing. These bridge plug can be set by drop a ball and up lift, do not need any setting tools. They are available for 4 1/4” through 20” setting range.

Features:


n Can be released by right hand rotation in an emergency


13

Model “SRWB” wireline set retrievable bridge plug is a medium perfor¬mance retrievable bridge plug that is run and set by a wireline pressure setting tool and retrieved by either tubing or sandline. The plug is used for zone isolation, formation fracturing, acidizing, and wellhead repair and can be lubricated in and out of the well under pressure, thereby eliminating snubbing tubing or killing the well. The plug features a balanced equal¬izing value located immediately above the packing element system. Caged, bi-directional, one piece slips are located below the packing and firmly anchor the plug against pressure differentials from above or below. The plug is retrieved by ratcheting onto the retriev¬ing neck, picking up four inches to equalize, setting down to uplock, then picking up to remove from well. No rotation is required to retrieve.

Features:

n Compact, fast running, electric wireline set.

n Tubing or sandline retrieved

n No rotation required

n Balanced equalizing valve opens upwardly which reduces possibility of accidental opening.

n Equalizes close to top of packing elements tubing manipulation from the surface for better control

SPECIFICATIONS

Part NumberCasing OD Casing Wt Setting Range Tool OD

Setting Force Tubing Retrieving

Tool(in) (lbs/ft) Min(in) Max(in) (in) (lbs)

D17-0450-001 4-1/2” 9.5-13.5 3.92 4.09 3.771

30,000

D17-0450-023D17-0500-001 5 15-18 4.276 4.408 4.125

D17-0550-001

5-1/2”

20-23 4.67 4.778 4.5

D17-0550-049D17-0550-002 15.5-20 4.778 4.95 4.641

D17-0550-003 13-15.5 4.95 5.044 4.781

D17-0625-001 6-5/8” 24-32 5.675 5.921 5.5

55,000

D17-0700-053

D17-0625-001

7”

32-35 6.004 6.094 5.812

D17-0700-002 26-29 6.184 6.276 5.968

D17-0700-003 23-26 6.276 6.366 6.078

D17-0700-004 17-20 6.456 6.538 6.266

D17-0762-0017-5/8”

33.7-39 6.625 6.765 6.453

D17-0762-002 24-29.7 6.875 7.025 6.672

D17-0862-001 8-5/8” 32-40 7.725 7.921 7.531 D17-0862-080

D17-0962-0019-5/8”

40-47 8.681 8.835 8.437D17-0962-046

D17-0962-002 47-53.5 8.535 8.681 8.218

S RW B W I R E L I N E SE T B R I D G E P LU G S (R E T R I E VA B L E)

14


SPECIFICATIONS

Part Number

Casing OD

Casing Wt Setting RangeTool OD

Re-lease Force

Setting tool

Setting kitsSeal Nip-ple


D22-0450-001 4 1/2 9.5-16.6 3.826 4.09 3.59

33,000

#10 D22-0450-102D22-0450-010D22-0450-012

D22-0500-001 5 11.5-20.8 4.156 4.56 3.93

#20

D22-0500-101

D22-0550-001 5 1/2 13-23 4.58 5.044 4.31 D22-0550-102

D22-0575-001 5 3/4 14-26 4.89 5.29 4.7 D22-0575-101

D22-0662-001 6 5/8 17-32 5.595 6.135 5.37

50,000

D22-0662-101

D22-0700-010D22-0700-012

D22-0700-001 7 17-35 6.004 6.538 5.68 D22-0700-152

D22-0762-001 7 5/8 20-39 6.625 7.125 6.31 D22-0762-101

D22-0862-001 8 5/8 24-49 7.511 8.097 7.12 D22-0862-101

D22-0962-001 9 5/8 29.3-58.4 8.435 9.063 8.12 D22-0962-103

D22-1075-001 10 3/432.75-60.7

9.66 10.192 9.43 D22-1075-101

D22-1176-001 11 3/4 38-60 10.772 11.15 10.43 D22-1176-101

D22-1175-001 11 3/4 60-83 10.192 10.772 9.94 D22-1175-101

D22-1337-001 13 3/8 48-80.7 12.175 12.715 11.88 D22-1337-101

D22-1600-001 16 65-118 14.576 15.25 14.12 D22-1600-101

D22-2000-001 20 94-133 18.73 19.124 18.37 D22-2000-101

ST W R W I R E L I N E SE T CE M E N T R E TA I N E R

Model STWR Wireline Set Sleeve Valve Cement Retainers are used for secondary cementing operations. These drillable retainers set securely in any hardness casing. A ratchet lock ring stores the set¬ting force in the retainer. The one piece packing element and metal back up rings combine for a superior seal. The case hardened, one piece slips virtually eliminate premature setting, yet can be easily drilled out. They are available for 4 1/2” through 20” casing.

Features:





n Can be set directly with Baker wireline setting tools

n Shear studs are Baker style and connect directly to the Baker Adjuster Sub

n These retainers can be run directly on Baker Setting Sleeves and Adjuster Subs

n Crossovers arenot required

15

ST M R M EC H A N I C A L CE M E N T R E TA I N E R

Model STMR Tubing Set Sleeve Valve Cement Retainers are used for secondary cementing operations. These drillable retainers set securely in any hardness casing. A ratchet lock ring stores the setting force in the retainer. The one piece packing element and metal back up rings combine for a superior seal. The case hardened, one piece slips virtually eliminate premature setting, yet can be easily drilled out. They are available for 4 1/2” through 16” casing.

Features:





n Pressure balanced sleeve valve is opened and closed by tubing manipulation from the surface for better control

n Set with Model STSR Mechanical Setting Tool

SPECIFICATIONS

Part NumberCasing OD Casing Wt Setting Range Tool OD

Release Force Setting Tool


D22-0450-002 4 1/2 9.5-16.6 3.826 4.09 3.59

33,000

D22-0450-005D22-0500-002 5 11.5-20.8 4.156 4.56 3.93

D22-0550-002 5 1/2 13-23 4.58 5.044 4.31 D22-0550-105

D22-0575-002 5 3/4 14-26 4.89 5.29 4.7 D22-0575-005

D22-0662-002 6 5/8 17-32 5.595 6.135 5.37

50,000

D22-0662-005

D22-0700-002 7 17-35 6.004 6.538 5.68 D22-0700-205

D22-0762-002 7 5/8 20-39 6.625 7.125 6.31 D22-0762-005

D22-0862-002 8 5/8 24-49 7.511 8.097 7.12 D22-0862-005

D22-0962-002 9 5/8 29.3-58.4 8.435 9.063 8.12 D22-0962-005

D22-1075-002 10 3/4 32.75-60.7 9.66 10.192 9.43 D22-1075-005

D22-1176-002 11 3/4 38-60 10.772 11.15 10.43 D22-1176-005

D22-1175-002 11 3/4 60-83 10.192 10.772 9.94 D22-1175-005

D22-1337-002 13 3/8 48-80.7 12.175 12.715 11.88 D22-1337-005

D22-1600-002 16 65-118 14.576 15.25 14.12 D22-1600-005

16


STSS ST I N G E R SE A L A SSE M B LY

Model STSS Stinger Seal Assembly is a tubing conveyed latching seal assembly that is used to operate the sleeve-valve in an STWR Cement retainer previously set on wireline line. The STSS should always be run with a STTC Tubing Centralizer to provide for easier entry into the Cement retainer.

Features:

n Provide positive control when the work string is picked up to close the sleeve-valve. Re-engages each time the work string is lowered to open sleeve-valve

n Helps prevent seal from pumping out during pumping operations or tubing testing

n One size operates several sizes of retainers

n Rotate or Snap-out release

n Can Run with Baker Cement Retainers

SPECIFICATIONS

STSS part number

D-2 part numberCasing OD Casing Wt Retainer OD

Connection thread(in) (lbs/ft) (in)

D22-0450-010 D22-0450-012

4 1/2 9.5-16.6 3.59

2 3/8"-8RD EU5 11.5-20.8 3.93

5 1/2 13-23 4.31

5 3/4 14-26 4.7

D22-0700-010 D22-0700-012

6 5/8 17-32 5.37

2 7/8"-8RD EU

7 17-35 5.68

7 5/8 20-39 6.31

8 5/8 24-49 7.12

9 5/8 29.3-58.4 8.12

10 3/4 32.75-60.7 9.43

11 3/4 38-60 10.43

11 3/4 60-83 9.94

13 3/8 48-80.7 11.88

16 65-118 14.12

20 94-133 18.37

17

W I R E L I N E SE TT I N G TO O L S

Wireline pressure setting tools come in single and multi-stage. Single stage tools provide dynamic force which is used to set bridge plugs ,production packer or cement retainers. Multi-stage setting tools feature increased stoke length to enable the setting of casing patches, long travel bridge plugs or any requiring more than the normal stroke and tension of conventional pressure setting tools. The force is created by the gradual burning of a high temperature power charge which produces high pressure gas that is contained by an o-ring sealed top piston. The piston applies the necessary stroke and tension to set and release from the equipment.

SPECIFICATIONS

Part number Model TypeTool OD

Working temperature /pressure power charge

Setting force MAX

fluid Column pressure

(in) (°F/PSI) (lbs) PSI

D26-0350-001 SWSB #20 3 1/2 400 / 20,000 D26-0350-043 60,000 15,000

D26-0168-001

SWSG GO

1.72 400 / 10,000 D26-0168-031 15,000 10,000

D26-0350-003 3 1/2 400 / 15,000

D26-0150-020

60,000 8,000

D26-0350-005 3 1/2 400 / 20,000D26-0350-043

15,000

18


The hydraulic setting tools are used to run and set packers, bridge plugs and cement retainers on a work string, production tubing or coiled tubing. The setting tool translate hydraulic pressure applied to the tubing to a force transmitted through the adapter kit to the slips and pack off the sealing element of these tools. It allows setting in high-angle or deviated wells where it is often difficult to use wireline equipment.

SPECIFICATIONS

Part number Model TypeTool OD

Piston area

Setting force MAX

Tension MAX Length Top thread

(in) (in^2) (lbs) (lbs)

D26-1172-001 SHSG 1 11/16 1.72 2.238 15,000 25,000 66.88 1”AMMT

D26-1275-001 SHSB #10 3.125 6.68 50,000 60,000 58.47 2 3/8”-8RD EU

D26-1387-001 SHSB #20 3 7/8 11.85 60,000 78,000 59.50 2 7/8”-8RD EU

D26-1387-002 SHSG GO 3 7/8 11.85 60,000 78,000 73.30 2 7/8”-8RD EU

D26-1387-003 SHSB-1 #20/GO 3 7/8 15 60,000 70,000 49.07 2 7/8”-8RD EU

H Y D R AU L I C SE TT I N G TO O L S

19

STS B M EC H A N I C A L SE TT I N G TO O L

Model STSB Mechanical Setting Tools are used to mechanically set STMB Bridge Plugs. It is designed to contain the upper slips of Bridge Plug in a safe retracted position while running to setting depth. The upper slips are released by right hand rotation and slacking off on the work string.

Features:

n Special designed Bow Spring provide positive control and allows one size Mechanical Setting Tools to cover a large range of casing weight

n Locked with Bridge Plug

n The Upper slips are held in a safe retracted position while running

n Can quickly be configured to set STMR Cement Retainers

SPECIFICATIONS

Part numberCasing OD Casing Wt

Bridge plug Top thread(in) (lbs/ft)

D22-0450-0044 1/2 9.5-16.6

D22-0450-009

2 3/8”-8RD EU

D22-0450-006

5 11.5-20.8 D22-0500-009

D22-0550-004 5 1/2 13-23D22-0550-009

D22-0550-006

D22-0575-004 5 3/4 14-26 D22-0575-009

D22-0662-004 6 5/8 17-32 D22-0662-009

2 7/8”-8RD EU

D22-0700-004 7 17-35D22-0700-009

D22-0700-006

D22-0762-004 7 5/8 20-39 D22-0762-009

D22-0862-004 8 5/8 24-49 D22-0862-009

D22-0962-004 9 5/8 29.3-58.4D22-0962-009

D22-0962-006

D22-1075-004 10 3/4 32.75-60.7 D22-1075-009

D22-1176-004 11 3/4 38-60 D22-1176-009

D22-1175-004 11 3/4 60-83 D22-1175-009

D22-1337-004 13 3/8 48-80.7 D22-1337-009

D22-1600-004 16 65-118 D22-1600-009

20


Model STSR Mechanical Setting Tools are used to mechanically set STMR Sleeve-Valve Cement Retainers. This tool incorporates both a stinger seal and mechanical setting function. In addition, it has a built-in snap-latch, allowing the tool to be latched into the cement retainer with set-down weight and released with either upstrain or right-hand rotation. The sleeve-valve on the cement retainer is in the open position while being run in the well. When the setting procedure is completed, the sleeve-valve may be closed by picking up two inches at the tools or opened by slacking off two inches. The snap-latch feature allows the sleeve-valve to be shifted open or closed while the tubing is still anchored to the retainer. Normally the valve is run open so the tubing may fill. However, for pressure testing the tubing, while running, the valve can be run closed. Cement Retainers can be set and pressure tested in a single trip.

Features:

n Special designed Bow Spring provide positive control and allows one size Mechanical Setting Tools to cover a large range of casing weight

n The Upper slips are held in a safe retracted position while running

n Allows users to set, pressure test tubing, and squeeze in a single trip

n Can quickly be configured to set STMR Cement Retainers or STMB Bridge Plugs

SPECIFICATIONS


Retainer Top thread(in) (lbs/ft)

D22-0450-0054 1/2 9.5-16.6 D22-0450-002

2 3/8”-8RD EU5 11.5-20.8 D22-0500-002

D22-0550-105 5 1/2 13-23 D22-0550-002 2 7/8”-8RD EU

D22-0575-005 5 3/4 14-26 D22-0575-002 2 3/8”-8RD EU

D22-0662-005 6 5/8 17-32 D22-0662-002

2 7/8”-8RD EU

D22-0700-205 7 17-35 D22-0700-002

D22-0762-005 7 5/8 20-39 D22-0762-002

D22-0862-005 8 5/8 24-49 D22-0862-002

D22-0962-005 9 5/8 29.3-58.4 D22-0962-002

D22-1075-005 10 3/4 32.75-60.7 D22-1075-002

D22-1176-005 11 3/4 38-60 D22-1176-002

D22-1175-005 11 3/4 60-83 D22-1175-002

D22-1337-005 13 3/8 48-80.7 D22-1337-002

D22-1600-005 16 65-118 D22-1600-002

STS R M EC H A N I C A L SE TT I N G TO O L

21

SPECIFICATIONS


Connection threadID

(in) (lbs/ft) (in)

D22-0450-011

4 1/2 9.5-16.6

2 3/8”-8RD EU 1

5 11.5-20.8

5 1/2 23

D22-0550-0115 1/2 13-23

5 3/4 14-26

D22-0662-011 6 5/8 17-32

2 7/8”-8RD EU 2.50

D22-0700-011 7 17-35

D22-0762-011 7 5/8 20-39

D22-0862-011 8 5/8 24-49

D22-0962-011 9 5/8 29.3-58.4

D22-1075-011 10 3/4 32.75-60.7

D22-1176-011 11 3/4 38-60

D22-1175-011 11 3/4 60-83

D22-1337-011 13 3/8 48-80.7

D22-1600-011 16 65-118

D22-2000-011 20 94-133

STTC T U B I N G CE N T R A L I Z E R

Model STTC Tubing Centralizer is used to center the tubing and provide for easier entry into an STWR Cement retainer previously set by wireline.

Features:

n Provide positive control and allows one size Tubing centralizer to cover a large range of casing weights.

n Most parts are common to the STSR Mechanical Setting Tool.

n Allows tubing torque to be transmitted to tools below.

22


SPECIFICATIONS

Part number

Casing OD

Casing Wt Setting range Tool OD Seal boreRelease force Seal nipple

(in) (lbs/ft) Min(in) Max(in) (in) (in) (lbs)

D51-0450-001

4 1/2 9.5-13.5

3.92 4.154 3.75 1.968 29,000 D51-0450-1514 3/4 16.0-18.0

5 21

D51-0550-001 5 1/2 20.0-23.0 4.625 4.811 4.3282.687 38,000 D51-0550-198

D51-0550-002 5 1/2 13.0-17.0 4.812 5.044 4.5

D51-0700-0016 5/8 17.0-32.0

5.675 6.135 5.468

3.25

47,000

D51-0700-150

7 32.0-38.0

D51-0700-0026 5/8 17-0-20.0

6.004 6.366 5.6877 23.0-35.0

D51-0700-0037 17.0-20.0

6.456 6.765 6.187

48,000

7 5/8 33.7-39.0

D51-0762-001 7 5/8 24.0-39.0 6.625 7.025 6.375

D51-0862-001 8 5/8 24.0-49.0 7.511 8.097 7.25

4 D51-0700-339

D51-0962-001 9 5/8 29.3-53.5 8.435 9.063 8.125

D51-1075-001 10 3/4 60.7-81.0 9.25 9.66 8.718

D51-1175-00110 3/4 32.7-55.5

9.76 11.15 9.538.0-60.0

SP P-C P E R M A N E N T P R O D U C T I O N PAC K E R S

Model SPP-C Production Packers are used on installations requiring premium production equipment for high temperatures and pressures. These wireline set millable packers are available for 4 1/2” through 11 3/4” casing.

Features:



n Threaded pin down connection for easy installation of accessories, such as Screw-Out ornok-Out Plug kits

n Can be set with GO, Baker or Gearhart wireline Setting Tools

23

SP P-XC P E R M A N E N T P R O D U C T I O N PAC K E R S

Model SPP-XC Permanent Production Packers have a larger ID through the packer bore making them an excellent choice for parallel string installations and similar applications. These wireline set millable packers are available for 4 1/2” through 9 5/8” casing.

Features:



n Three piece packing element and rocker action metal back up rings combine for a superior seal

n Threaded pin down connection for easy installation of accessories


SPECIFICATIONS

Part numberCasing OD Casing Wt Setting range Tool OD Seal bore Release

forceSeal nipple

(in) (lbs/ft) Min(in) Max(in) (in) (in)

D51-0450-011 4 1/2 9.5-13.5 3.92 4.124 3.718

2.5 28,000 D51-0500-151D51-0500-010 5 15.0-21.0 4.125 4.436 3.968

D51-0500-0105 11.5-13.0

4.437 4.67 4.255 1/2 23.0-26.0

D51-0550-010 5 1/2 20.0-23.0 4.625 4.811 4.437

3 38,000 D51-0550-366D51-0550-011 5 1/2 14.0-17.0 4.812 5.012 4.562

D51-0550-012 5 1/2 13.0-14.0 4.976 5.124 4.75

D51-0700-0106 5/8 20.0-24.0

6.875 6.094 5.687

4 48,000 D51-0700-339

7 32.0-38.0

D51-0700-0116 5/8 17

6.095 6.276 5.8757 26.0-29.0

D51-0700-012 7 20.0-23.0 6.277 6.456 6

D51-0700-0137 17.0-20.0

6.456 6.765 6.257 5/8 33.7-39.0

D51-0762-010 7 5/8 20.0-29.7 6.875 7.125 6.625

D51-0962-010 9 5/8 29.3-53.5 8.535 9.063 8.125 4.75 55,000 D51-0700-458

24


Model SQS Hydro-Set retainer production packers are hydraulically set versions of the Model DGXL-R Packers. Both models permit the maximum possible bore through the seal accessory which is latched into the packer. An independent polished bore can be connected on the top of the packer to get a max ID. The hydraulic setting mechanism makes the SQS Packers particularly suitable for use in highly deviated wells. Careful choice of materials for components, which are exposed to the well fluids, enables the packers to be used in a wide range of operating conditions.

Features:

n Solid, slim line construction and a packing element system which resists swab-off. This permits a fast run-in without fear of impact damage or premature setting, yet packs off securely and permanently when the packer is set.

n Two opposed sets of full circle, full strength slips ensure that the packer will stay where it is set.

n Interlocked expandable metal back-up rings contact the casing and create a positive barrier to packing element extrusion.

n Setting requiresno rotation or reciprocation, thereby eliminating the problems of spacing out, landing, etc.

n Run with Anchor Seal Locator or an appropriative setting tool.

SPECIFICATIONS

Part Number

Tool Casing Setting RangePressure/temp Setting Tool

Seal Locator In packer

IDOD ID OD Weight Min Max

inch inch inch lbs/ft inch inch Psi/°F inch

D50-5010-300 3.968 1.938 5 15-21 4.125 4.436

10k/300

D50-5010-380 D50-5010-381 1.938

D50-5010-300 4.442.375 5 1/2

20-23 4.625 4.811D50-5510-380 D50-5510-381 2.375

D50-5010-301 4.56 13-17 4.812 5.044

D50-7011-310 5.875

47

26-32 6.094 6.276

10k/350 D50-7011-390D50-7011-388

3D50-7011-311 6.000 20-26 6.276 6.456

D50-7611-001 6.732 7 5/8 20-24 7.025 7.125 D50-7611-390

SQS H Y D R O-SE T R E TA I N E R P R O D U C T I O N PAC K E R S

25

SP P-R R E T R I E VA B L E P R O D U C T I O N PAC K E R S

Model SPP-R Retrievable Production Packers are used for production, injection, testing, fracturing, squeeze cementing, gravel packing and as temporary bridge plugs. These wireline set packers are retrievable with tubing, sandline, electric wireline or coil tubing and require no rotation to release or set. The bi-directional one-piece slips hold high pressure differentials from either direction. SPP-R packers use conventional permanent packer seal nipples and accessories. They are available for 3 1/2” through 9 5/8”.

Features:


n No rotation required to set or release

n Three piece packing element system

n Uses conventional drillable packer sealnipples and accessories

n Threaded pin down connection for easy installation of accessories, such as Screw-Out ornok-Out Plug kits


SPECIFICATIONS

Part number

Casing OD

Casing Wt Setting range Tool OD Seal boreRelease force Seal nipple

(in) (lbs/ft) Min(in) Max(in) (in) (in) (lbs)

D52-0350-001 3 1/2 9.2-10.2 2.922 3.031 2.75 2 13,000 D52-0350-046

D52-0450-002 4 1/2 9.5-13.5 3.92 4.09 3.771 1.968

29,000

D52-0450-095

D52-0450-001 4 1/2 9.5-11.6 4 4.09 3.8122.39 D51-0450-069

D52-0500-001 5 15.0-18.0 4.276 4.408 4.062

D52-0550-002 5 1/2 20.0-23.0 4.67 4.778 4.52.687 35,000 D51-0550-172‐

D52-0550-001 5 1/2 13.0-17-0 4.892 5.044 4.656

D52-0700-0016 5/8 24.0-32.0

5.675 5.921 5.5

3.25 48,000 D51-0700-121

7 38

D52-0700-0026 5/8 17.0-20.0

6.004 6.184 5.8127 29.0-35.0

D52-0700-003 7 20.0-29.0 6.184 6.456 5.875

D52-0762-0017 17.0-20.0

6.456 6.765 6.1877 5/8 33.7-39.0

D52-0762-002 7 5/8 20.0-29.7 6.875 7.125 6.652

D52-0862-001 8 5/8 36.0-49.0 7.511 7.825 7.25

4

55,000

D51-0700-318D52-0862-002 8 5/8 24.0-36.0 7.825 8.097 7.562

D52-0962-001 9 5/8 43.5-53.5 8.535 8.755 8.187

D52-0962-002 9 5/8 29.3-43.5 8.755 9.063 8.437

D52-0962-011 9 5/8 43.5-53.5 8.535 8.755 8.1874.75 D52-0962-075‐

D52-0962-012 9 5/8 29.3-43.5 8.755 9.063 8.437

26


SPECIFICATIONS

Part numberCasing OD Casing Wt Setting range Tool OD Tool ID Connection

thread(in) (lbs/ft) Min(in) Max(in) (in) ( in )D45-0500-102

4 1/2 9.5-13.5 3.91 4.09 3.771.94 2 3/8”-8RD EU

D45-0500-101

1.9

2 7/8”-8RD EUD45-0500-100

2 3/8”-8RD EU

D45-0500-200 5 15-18 4.25 4.408 4.13

D45-0500-300 5 11.5-15

4.408 4.56 4.255 1/2 26

D45-0550-120 5 1/2

20-23 4.625 4.778 4.5

2

D45-0550-140 15.5-20 4.778 4.95 4.64

D45-0550-200 5 1/2 13-15.5

4.95 5.19 4.785 3/4 22.56 26

D45-0550-3006

20-23 5.191 5.39 5.06D45-0550-400 15-18 5.391 5.56 5.16D45-0550-520

6 5/8

34 5.561 5.609 5.41D45-0550-540 28-32 5.61 5.791 5.48D45-0550-560 24-28 5.791 5.921 5.48D45-0662-120 28-32 5.6 5.791 5.48

2.42

2 7/8”-8RD EU

D45-0662-1406 5/8 24-28

5.791 5.921 5.597 38

D45-0662-2006 5/8 17-20

5.922 6.135 5.787 32-35

D45-0700-120 6 5/8 24

5.83 5.937 5.667 38

D45-0700-1406 5/8 17-20

5.938 6.135 5.817 32-35

D45-0700-220

726-29 6.136 6.276 5.97

D45-0700-520 3 1/2”-8RD EUD45-0700-240 20-26 6.276 6.456 6.08

2 7/8”-8RD EUD45-0700-320 17-20 6.454 6.578 6.27D45-0700-340

7 5/833.7-39 6.579 6.797 6.45

D45-0700-420 24-29.7 6.798 7.025 6.67D45-0700-440 20-24 7.025 7.125 6.81D45-0862-120

8 5/844-49 7.511 7.687 7.31

3.47

3 1/2”-8RD EU

D45-0862-140 32-40 7.688 7.921 7.53D45-0862-200 20-28 7.922 8.191 7.78D45-0962-120

9 5/8

47-53.5 8.343 8.681 8.22

3.94D45-0962-140 40-47 8.681 8.835 8.44D45-0962-200 29.3-36 8.836 9.063 8.59D45-1962-140 40-47 8.681 8.835 8.44

2 7/8”-8RD EUD45-1962-200 29.3-36 8.836 9.063 8.59

SM R-D D O U B L E G R I P R E T R I E VA B L E PAC K E R

Model SMR-D Double Grip Retrievable Casing Packers are used in production, stimulation and testing applications. Their hydraulic hold down is below the pressure equalization valve. They feature a proven three element packing system and a balance sleeve device to assist in keeping the by-pass closed. They are available for 4 1/2” through 9 5/8” casing.

Features:



n Hydraulic hold down button unit with large internal flow path located below the bypass valve to reduce element swabbing and button wicker dulling

n Surface controlled combination bypass and equalizing valve

n Tubing pressure actuated collet lock to eliminate excessive set down weight requirements

n Rocker type Slips

n Parts are interchangeable with other manufacturers

27

SM R-D L A R G E B O R E D O U B L E G R I P R E T R I E VA B L E PAC K E R

Large Bore Model SMR-D Double Grip Retrievable Casing Packers are used in production, stimulation and testing operations where maximum I.D. is required

Their hydraulic hold down is below the pressure equalization valve. They feature a proven three element packing system and a balance sleeve device to assist in keeping the by-pass closed. They are available for 5 1/2” through 7 5/8” casing.

Features:



n Hydraulic hold down button unit with large internal flow path located below the bypass valve to reduce element swabbing and button wicker dulling


n Tubing pressure actuated collet lock to eliminate excessive set down weight requirements

n Rocker type Slips


n Large bore

SPECIFICATIONS

Part numberCasing OD Casing Wt Setting range Tool OD Tool ID

Connection thread(in) (lbs/ft) Min(in) Max(in) (in) ( in )

D45-1550-120 5 1/2

20-23 4.625 4.778 4.5

2 3/8 2 7/8”-8RD EU

D45-1550-140 15.5-20 4.778 4.95 4.64

D45-1550-200

5 1/2 13-15.5

4.95 5.19 4.785 3/4 22.5

6 26

D45-1700-1406 5/8 17-20

5.938 6.135 5.81

3 3 1/2”-8RD EU

7 32-35

D45-1700-220

7

26-29 6.136 6.276 5.97D45-1700-520

D45-1700-240 20-26 6.276 6.456 6.08

D45-1700-320 17-20 6.454 6.578 6.27

D45-1700-340

7 5/8

33.7-39 6.579 6.797 6.45

D45-1700-420 24-29.7 6.798 7.025 6.67

D45-1700-440 20-24 7.025 7.125 6.81

28


SM R-S S I N G L E G R I P R E T R I E VA B L E PAC K E R

Model SMR-S Single Grip Retrievable Casing Packers are used in production as a convention long stroke Packer. They feature a proven three element packing system and a large by-pass area through the Packer. They are available for 4” through 9 5/8” casing.

Features:


n Three pieces packing element system

n Large by-pass area


n Rocker type Slips


SPECIFICATIONS

Part numberCasing OD Casing Wt Setting range Tool OD Tool ID connection

thread(in) (lbs/ft) Min(in) Max(in) (in) ( in )D46-0400-100 4 9.5-11.6 3.428 3.546 3.303

1.5

2 3/8” EU

D46-0500-2004 1/2

15.1 3.754 3.826 3.62D46-0450-100 9.5-13.5 3.91 4.09 3.771

1.95D46-0500-200

515-18 4.25 4.408 4.125

D46-0500-30011.5-15

4.408 4.56 4.25

5 1/2

26D46-0550-120 20-23 4.625 4.778 4.5

1.969

D46-0550-140 15.5-20 4.778 4.95 4.641

D46-0550-20013-15.5

4.95 5.19 4.7815 3/4 22.5

626

D46-0550-300 20-23 5.191 5.39 5.062D46-0550-400 15-18 5.391 5.56 5.156D46-0550-520

6 5/834 5.561 5.609 5.406

D46-0550-540 28-32 5.61 5.791 5.484D46-0550-560 24-28 5.791 5.921 5.484D46-1550-120

5 1/220-23 4.625 4.777 4.5

2.375

2 7/8”EU

D46-1550-140 17-20 4.778 4.892 4.641D46-1550-200 13-15.5 4.893 5.044 4.781D46-0662-120 6 5/8 28-32 5.6 5.791 5.475

D46-0662-1406 5/8 24-28

5.791 5.921 5.5887 38

D46-0662-2006 5/8 17-20

5.922 6.135 5.781

2.5

7 32-35

D46-0700-1206 5/8 24

5.83 5.937 5.6567 38

D46-0700-1406 5/8 17-20

5.938 6.135 5.812

7

32-35D46-0700-220 26-29 6.136 6.276 5.968D46-0700-240 20-26 6.276 6.456 6.078D46-0700-320 17-20 6.456 6.578 6.266D46-0700-340

7 5/833.7-39 6.579 6.797 6.453

D46-0700-420 24-29.7 6.798 7.025 6.672D46-0700-440 20-24 7.025 7.125 6.812

3 1/2” EU

D46-0862-1208 5/8

44-49 7.511 7.687 7.3123.469D46-0862-140 32-40 7.688 7.921 7.531

D46-0862-200 20-28 7.922 8.191 7.781D46-0962-120

9 5/847-53.5 8.343 8.681 8.218

3.92D46-0962-140 40-47 8.681 8.835 8.437D46-0962-200 29.3-36 8.836 9.063 8.593

29

SPECIFICATIONS

Part numberCasing OD Casing Wt Setting range Tool OD Tool ID connection

thread(in) (lbs/ft) Min(in) Max(in) ( in ) ( in )

D42-5360-0024 1/2

9.5-13.5 3.92 4.09 3.75

1.938 2 3/8”-8RD EU

D42-5360-003 13.5-15.1 3.826 3.92 3.65

D42-5360-0065

18.0-20.8 4.156 4.276 4

D42-5360-007 11.5-15.0 4.408 4.56 4.125

D42-5361-001

5 1/2

20.0-23.0 4.67 4.778 4.5

D42-5361-002 14.0-20.0 4.778 5.012 4.625

D42-5361-006 20.0-23.0 4.67 4.778 4.52.375

2 7/8”-8RD EUD42-5361-007 15.5-20.0 4.778 4.95 4.625

D42-5362-004

7

26.0-32.0 6.094 6.276 5.8752.5

D42-5362-005 17.0-26.0 6.276 6.538 6

D42-5332-006 26.0-32.0 6.094 6.276 5.8753 3 1/2”-8RD EU

D42-5332-007 17.0-26.0 6.276 6.538 6

D42-5363-001

7 5/8

33.7-39 6.625 6.765 6.4532.5 2 7/8”-8RD EU

D42-5363-004 24-29.7 6.798 7.025 6.672

D42-5333-002 33.7-39 6.625 6.765 6.4533 3 1/2”-8RD EU

D42-5333-003 24-29.7 6.798 7.025 6.672

D42-5345-0019 5/8

43.5-53.5 8.535 8.755 8.2504 41/2”-8RD EU

D42-5345-002 32.3-43.5 8.755 9.001 8.500

SM A M EC H A N I C A L SE T R E T R I E VA B L E P R O D U C T I O N PAC K E R S

The Model SMA single string Mechanical Production Packer is a retrievable, double-grip compression or tension-set production packer that holds pressure from above or below. Once set the tubing string can be left in tension, compression, or in a neutral position. A large internal bypass reduces the swabbing effect during run-in and retrieval, and closes when the packer is set. When the packer is released, the bypass opens first, allowing the pressure to equalize before the upper slips are pulled from the casing. The Model SMA also features an upper slip releasing system that reduces the force required to release the packer. A non-directional slip is released first, making it easier to release the other slips. These flexible features allow the SMA to be run in a variety of applications ranging from Production Packer to Bridge Plug to Service Packer.

Features:

n Internal bypass reduces swabbing.

n Holds high pressure differentials from above or below.

n Can be set using tension or compression.

n Only one-quarter right rotation is required to set and release.

n Tubing string can be held in tension, compression orneutral set while the packer remains engaged.

n Optional shear release features available upon request.

n Packing element options are available for hostile environments.

n Bypass valve is below upper slips so the debris is washed from slips when the valve is opened.

30


SPECIFICATIONS


Connection thread(in) (lbs/ft) Min(in) Max(in) (in) ( in )

D47-0500-1204 1/2

11.6-13.5 3.91 4.003.771

1.97

2 3/8”-8RD EU

D47-0500-140 9.5-10.5 4.001 4.090D47-0500-200

515-18 4.25 4.408 4.125

D47-0500-30011.5-15

4.408 4.56 4.25

5 1/2

26D47-0550-120 20-23 4.625 4.778 4.5

2

D47-0550-140 15.5-20 4.778 4.95 4.641

D47-0550-20013-15.5

4.95 5.19 4.7815 3/4 22.5

626

D47-0550-300 20-23 5.191 5.39 5.062D47-0550-400 15-18 5.391 5.56 5.156D47-0550-500

6 5/8

34 5.561 5.609 5.406D47-0550-600 24-32 5.561 5.921 5.484D47-0550-700 17-24 5.992 6.135 5.781

D47-0700-12024

5.83 5.937 5.656

2.438 2 7/8”-8RD EU

7 38

D47-0700-1406 5/8 17-20

5.938 6.135 5.812

7

32-35D47-0700-220 26-29 6.136 6.276 5.968D47-0700-240 20-26 6.276 6.456 6.078D47-0700-320 17-20 6.456 6.578 6.266D47-0700-340

7 5/833.7-39 6.579 6.797 6.453

D47-0700-420 24-29.7 6.798 7.025 6.672D47-0700-440 20-24 7.025 7.125 6.812D47-0862-120

8 5/844-49 7.511 7.687 7.312

3.481

4”-8RD NU

D47-0862-140 32-40 7.688 7.921 7.531D47-0862-200 20-28 7.922 8.191 7.781D47-0962-120

9 5/847-53.5 8.343 8.681 8.218

3.92D47-0962-140 40-47 8.681 8.835 8.437D47-0962-200 29.3-36 8.836 9.063 8.593

ST L S M EC H A N I C A L SE T R E T R I E VA B L E P R O D U C T I O N PAC K E R

Model STLS retrievable casing packer is a general purpose packer for production, injection, zone isolation, or remedial operations. It is a fullbore double-grip retrievable packer with an integral unloader. Opposed, non-transferring dovetail slips prevent movement of the packer in either direction due to pressure differentials, while allowing landing of the tubing in tension, compression, or neutral. The Lock Segments serve as a releasable Lock Ring to maintain pack-off once the packer is set, and locks the unloader in the closed position until the tool is released. The Split Lock and Control Segments allow the tool to be both set and released with right-hand rotation.

Features:

n Internal bypass reduces swabbing.

n Holds pressure differentials from above or below.

n Can be set using tension or compression.

n Set and released with right-hand rotation.

n Tubing string can be held in tension, compression orneutral set while the packer remains engaged.

n Packing element options are available for hostile environments.

31

SM J-A M EC H A N I C A L SE T R E T R I E VA B L E P R O D U C T I O N PAC K E R S

Model SMJ-A Retrievable Packers are used in Tubing Conveyed Perforating and Single Trip Production, stimulation, perforating, gravel packing and testing applications. The hydraulic hold down is below the pressure equalization valve. The tool features a proven three element packing system and a hydraulically controlled balance piston designed to keep the by-pass closed when set. The tools are available in 4 1/2” through 16” casing.

Features: n Set securely in any hardness casing, including premium grades.n Three piece packing element system with metal backups accommodate low and high

pressure applications for the broadest range of service. n Hydraulic hold down button unit with large internal flow path located below the bypass

valve to reduce element swabbing and button wicker dulling. These hold down piston type slips are set by pressure from below.

n Surface controlled combination bypass and equalizing valve. n Tubing pressure actuated hydraulic piston eliminates excessive set down weight

requirements. This feature is far more efficient than collet type locking systems. n Automatic Jay Unit, setting the packer is accomplished by running to depth, picking up a

few feet rotating 2/3 turns to the right and setting down. n Straight pickup of the tubing will first open the bypass valve and equalize pressure,

continued pickup will release the packer and automatically engage the packer in the running position for further operations up or down the hole.

n Wicker slips are machined from 4140 promising the ultimate sharpness and hardness. Lower slips are held fully retracted during running and retrieving. Slips and pistons are also avail able with carbide inserts.

n Long carbonized friction pads act independent of slips and allow trouble free passage through collar and recesses and stage tool profiles. Frication pads are also available with carbide inserts.

n All SMJ-A packers come with heavy duty long acme threads and dual O-Ring Backups on the body to coupling connections.

n All STJS-2A packers come standard with 8 Round top and bottom connections. For API IF connections see our SMJ-C packers. For other premium threads please contact sales.

SPECIFICATIONS


thread(in) (lbs/ft) Min(in) Max(in) ( in ) ( in )D40-0450-001 4 1/2 9.5-13.5 3.91 4.09 3.77 1.81

2 3/8”-8RD EU

D40-0500-001 5 15.0-18.0 4.25 4.408 4.13 1.81

D40-0500-0025 11.5-15.0

4.408 4.56 4.25 1.815 1/2 26

D40-0550-001 5 1/2 20.0-23.0 4.625 4.778 4.51 1.94D40-0550-002 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94D40-0550-003 5 1/2 13.0-15.5 4.95 5.19 4.78 1.94

D40-0700-0016 5/8 24

5.83 5.937 5.65 2.38

2 7/8”-8RD EU

7 38D40-0700-002 7 32.0-35.0 5.938 6.135 5.81 2.38D40-0700-003 7 26.0-29.0 6.136 6.276 5.97 2.38D40-0700-004 7 20.0-26.0 6.276 6.456 6.07 2.38D40-0700-005 7 17.0-20.0 6.456 6.578 6.27 2.38D40-0762-001 7 5/8 33.7-39.0 6.579 6.797 6.45 2.38D40-0762-002 7 5/8 24.0-29.7 6.798 7.025 6.67 2.38D40-0762-003 7 5/8 20.0-24.0 7.025 7.125 6.81 2.38D40-0862-004 8 5/8 57.4-60.7 7.062 7.25 6.98 3

3 1/2”-8RD EU

D40-0862-001 8 5/8 44.0-49.0 7.511 7.625 7.31 3D40-0862-002 8 5/8 32.0-40.0 7.725 7.921 7.53 3D40-0862-003 8 5/8 20.0-28.0 8.017 8.191 7.78 3D40-0962-001 9 5/8 47.0-53.5 8.535 8.681 8.21 3D40-0962-002 9 5/8 40.0-47.0 8.681 8.835 8.44 3D40-0962-003 9 5/8 29.3-36.0 8.921 9.063 8.59 3D40-1075-002 10 3/4 40.5-55.5 9.75 10.05 9.5 3D40-1175-002 11 3/4 60.0-83.0 10.192 11.772 10.06 3D40-1175-001 11 3/4 38.0-65.0 10.682 11.15 10.38 3D40-1337-001 13 3/8 48.0-72.0 12.347 12.715 12.13 3D40-1600-001 16 75.0-102.0 14.75 15.125 14.5 3.75

32


SPECIFICATIONS


Connection thread (in) (lbs/ft) Min(in) Max(in) ( in ) ( in )

D40-0550-201 5 1/2 20.0-23.0 4.625 4.778 4.51 1.94

2 3/8”-8RD EUD40-0550-202 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94

D40-0550-203 5 1/2 13.0-15.5 4.95 5.19 4.78 1.94

D40-0700-201 7 38 5.83 5.937 5.65 2.38

2 7/8”-8RD EU

D40-0700-202 7 32.0-35.0 5.938 6.135 5.81 2.38

D40-0700-203 7 26.0-29.0 6.136 6.276 5.97 2.38

D40-0700-204 7 20.0-26.0 6.276 6.456 6.07 2.38

D40-0700-205 7 17.0-20.0 6.456 6.578 6.27 2.38

SM J-B M EC H A N I C A L SE T R E T R I E VA B L E P R O D U C T I O N PAC K E R S

Model SMJ-B Retrievable Packers are used in Tubing Conveyed Perforating and Single Trip Production, stimulation, perforating, gravel packing and testing applications. The hydraulic hold down is below the pressure equalization valve. The tool features a proven three element packing system and a hydraulically controlled balance piston designed to keep the by-pass closed when set. The tools are available in 5 1/2” through 7” casing.

Features:

n Set securely in any hardness casing, including premium grades.

n Three piece packing element system with metal backups accommodate low and high pressure applications for the broadest range of service.

n Hydraulic hold down button unit with large internal flow path located below the bypass valve to reduce element swabbing and button wicker dulling. These hold down piston type slips are set by pressure from below.

n Surface controlled combination bypass and equalizing valve.

n Tubing pressure actuated hydraulic piston eliminates excessive set down weight requirements. This feature is far more efficient than collet type locking systems.

n Automatic Jay Unit, setting the packer is accomplished by running to depth, picking up a few feet rotating 2/3 turns to the right and setting down.

n Straight pickup of the tubing will first open the bypass valve and equalize pressure, continued pickup will release the packer and automatically engage the packer in the running position for further operations up or down the hole.

n Wicker slips are machined from 4140 promising the ultimate sharpness and hardness. Lower slips are held fully retracted during running and retrieving. Slips and pistons are also avail able with carbide inserts.

n Long carbonized friction pads act independent of slips and allow trouble free passage through collar and recesses and stage tool profiles. Frication pads are also available with carbide inserts.

n All SMJ-B packers come with heavy duty long acme threads and dual O-Ring Backups on the body to coupling connections.

n All SMJ-B packers come standard with 8 Round top and bottom connections.

33

SM J-C R E T R I E VA B L E STO R M PAC K E R

Model SMJ-C Retrievable Storm Packers are also used in production, stimulation, perforating, gravel packing and testing applications. The hydraulic hold down is below the pressure equalization valve. The tool features a proven three element packing system and a hydraulically controlled balance piston designed to keep the by-pass closed when set. The tools are available in 7” through 20” Casing. Comes standard with API IF thread forms.

Features: n Sets securely in any hardness casing, including premium grades. n Three piece packing element system with metal backups accommodates low and high

pressure applications for the broadest range of service. n Hydraulic hold down button unit with large internal flow path located below the bypass

valve to reduce element swabbing and button wicker dulling. these hold down piston type slips are set by pressure from below.

n Surface controlled combination bypass and equalizing valve. n Tubing pressure actuated hydraulic piston eliminate excessive set down weight

requirements. This feature is far more efficient than collet type locking systems. n Automatic Jay Unit, setting the packer is accomplished by running to depth, picking up

a few feet rotating 2/3 turns to the right and setting down. n Straight pickup of the tubing will first open the bypass valve and equalize pressure,

continued pickup will release the packer and automatically engage the packer in the running position for further operations up or down the hole.

n Wicker slips are machined from 4140 promising the ultimate sharpness and hardness. Lower slips are held fully retracted during running and retrieving. Slips and pistons are also available with carbide inserts.

n Friction pads are also available with carbide inserts. n All Thread connection come standard in API IF thread form. n All Pressure bearing o-rings have backups for higher pressure resistance. n Load and pressure resistance designed to meet high load applications.

SPECIFICATIONS


Connection thread(in) (lbs/ft) Min(in) Max(in) ( in ) (in)

D40-0500-601 5 15.0-18.0 4.25 4.408 4.13 1.75 2 3/8” IFD40-0550-601 5 1/2 20.0-23.0 4.625 4.778 4.51

1.938 2 7/8” IFD40-0550-603 5 1/2 15.5-20 4.778 4.95 4.64D40-0550-602 5 1/2 13.0-15.5 4.95 5.19 4.78

D40-0700-6016 5/8 24

5.83 5.937 5.65

2.25

2 7/8” IF7 38

D40-0700-602 7 32.0-35.0 5.938 6.135 5.81D40-0700-603 7

26.0-29.0 6.136 6.276 5.97D40-0700-604 3 1/2” IFD40-0700-605 7 20.0-26.0 6.276 6.456 6.07

2 7/8” IFD40-0700-606 7 17.0-20.0 6.456 6.578 6.27D40-0762-601 7 5/8 33.7-39.0 6.579 6.797 6.45D40-0762-602 7 5/8 24.0-29.7 6.798 7.025 6.67D40-0762-603 7 5/8 20.0-24.0 7.025 7.125 6.81D40-0862-601 8 5/8 44.0-49.0 7.511 7.625 7.31

2.75

3 1/2” IF

D40-0862-602 8 5/8 32.0-40.0 7.725 7.921 7.53D40-0862-603 8 5/8 20.0-28.0 8.017 8.191 7.78D40-0962-601 9 5/8 47.0-53.5 8.535 8.681 8.21D40-0962-602 9 5/8 40.0-47.0 8.681 8.835 8.44D40-0962-603 9 5/8 29.3-36.0 8.921 9.063 8.59D40-1075-601

10 3/4 40.5-55.5 9.75 10.05 9.5D40-1075-611

4 1/2” IFD40-1075-612 10 3/4 60.7 9.504 9.66 9.38D40-1175-602 11 3/4 60.0-83.0 10.192 10.772 10.06

3 1/2” IFD40-1175-601 11 3/4 38.0-65.0 10.682 11.15 10.38D40-1337-601 13 3/8 48.0-72.0 12.347 12.715 12.13D40-1337-611 13 3/8 48.0-72.0 12.347 12.715 12.13 4 1/2” IFD40-1600-601 16 75.0-102.0 14.75 15.125 14.5

3.75 4 1/2” IFD40-2000-601 20 94.0-133.0 18.73 19.124 18.4

34


SPECIFICATIONS



D48-0450-501 4 1/2 9.5-13.5 3.91 4.09 3.77 1.81

2 3/8”-8RD EUD48-0550-501 5 1/2 20.0-23.0 4.625 4.778 4.5 1.88

D48-0550-505 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94

D48-0550-502 5 1/2 13.0-15.5 4.95 5.19 4.78 1.94

D48-0550-503 5 1/2 20.0-23.0 4.625 4.778 4.5 1.87

2 7/8”-8RD EU

D48-0550-504 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94

D48-0700-5016 5/8 17.0-20.0

5.83 5.937 5.65 2.387 38

D48-0700-509 7 32.0-35.0 5.938 6.135 5.81 2.38

D48-0700-510 7 26.0-29.0 6.136 6.276 5.97 2.38

D48-0700-503 7 20.0-26.0 6.276 6.456 6.08 2.38

D48-0700-504 7 17.0-20.0 6.456 6.578 6.27 2.38

SM J-D R E T R I E VA B L E PAC K E R

Model SMJ-D Retrievable Packers are used for perforating, production, stimulation and testing applications. The hydraulic hold down is below the pressure equalization valve. “J” slot structure makes it easy and reliable to set and release.

Features:


n Long carbonized friction pads act independent of slips and allow trouble free passage through collar and recesses and stage tool profiles.


n Hydraulic hold down

35

SM C R E T R I E VA B L E PAC K E R S

SPECIFICATIONS

Part number

Casing OD

Casing Wt Setting range Tool OD Tool IDConnection thread

(in) (lbs/ft) Min(in) Max(in) ( in ) (in)

D48-0450-001 4 1/2 9.5-13.5 3.910 4.090 3.77

1.81 up 2 3/8”-8RD EUE bottom 2 3/8”-10RD NU

D48-0450-002 4 1/2 15.1 3.754 3.826 3.62

D48-0500-001 5 15.0-18.0 4.250 4.408 4.13

D48-0500-0025 11.5-15.0

4.408 4.560 4.25 1.81

2 3/8”-8RD EUE

5 1/2 26

D48-0550-001 5 1/2 20.0-23.0 4.626 4.778 4.50

1.88 D48-0550-002 5 1/2 15.5-20.0 4.778 4.950 4.64

D48-0550-003 5 1/2 13.0-15.5 4.950 5.044 4.78

D48-0700-0016 5/8 24

5.830 5.937 5.66

2.38 2 7/8”-8RD EUE

7 38

D48-0700-0026 5/8 17.0-20.0

5.938 6.135 5.81 7 32.0-35.0

D48-0700-003 7 26.0-29.0 6.136 6.276 5.97

D48-0700-0046 5/8 12

6.276 6.456 6.08 7 20.0-26.0

D48-0700-005 7 17.0-20.0 6.456 6.578 6.27

D48-0762-001 7 5/8 33.7-39.0 6.579 6.797 6.45

D48-0762-002 7 5/8 24.0-29.7 6.798 7.025 6.67

D48-0762-003 7 5/8 20.0-24.0 7.025 7.125 6.81

Model SMC Retrievable Packers are used for a variety of well treating and producing operations including squeeze cementing, formation fracturing, acidizing and testing. These double-grip single-string packers have a full opening bore that allows unrestricted fluid flow and easy passage of wireline tools. They also include hydraulically actuated upper button type slips and a built in pressure relief unloader. They are available for 4 1/2” through 7 5/8” casing.

Features:


n Long carbonized friction pads act independent of slips and allow trouble free passage through collar and recesses and stage tool profiles.

n Full opening bore, thick wall, one piece body


n Hydraulic hold down

n Surface controlled pressure equalization valve that requiresno separate unloader

36


SPECIFICATIONS


thread(in) (lbs/ft) Min(in) Max(in) ( in ) (in)

D43-0550-501 5 1/2 20.0-23.0 4.625 4.778 4.51 1.94

2 7/8”-8RD EU

D43-0550-502 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94

D43-0550-503 5 1/2 13.0-15.5 4.95 5.19 4.78 1.94

D43-0700-501 7 38 5.83 5.937 5.65 2.38

D43-0700-502 7 32.0-35.0 5.938 6.135 5.81 2.38

D43-0700-503 7 26.0-29.0 6.136 6.276 5.97 2.38

D43-0700-504 7 20.0-26.0 6.276 6.456 6.07 2.38

D43-0700-505 7 17.0-20.0 6.456 6.578 6.27 2.38

SM E PAC K E R (Y221)

Model SME Packers are used for perforation, testing, formation fracturing, acidizing and production applications. Easy operation, reliable.

Features:


n Length is moderate, easy for running

n Pick it up and turn right then push it to set; straight pulling to unset

37

SPECIFICATIONS


thread(in) (lbs/ft) Min(in) Max(in) ( in ) (in)D44-0450-100 4 9.5-11.6 3.428 3.548 3.188

1.937

2 3/8”-8RD EU

D44-0450-200 4 1/2 12.6-15.1 3.754 3.826 3.609D44-0500-100 4 1/2 9.5-13.5 3.91 4.09 3.771D44-0500-200 5 15-18 4.25 4.408 4.125

D44-0500-3005 11.5-15

4.408 4.56 4.255 1/2 26

D44-0550-120 5 1/2 20-23 4.625 4.778 4.5

1.978

D44-0550-140 5 1/2 15.5-20 4.778 4.95 4.641

D44-0550-2005 1/2 13-15.5

4.95 5.19 4.7815 3/4 22.56 26

D44-0550-300 6 20-23 5.191 5.39 5.062D44-0550-400 6 15-18 5.391 5.56 5.156D44-0550-540 6 5/8 28-32 5.61 5.791 5.484

D44-0700-1206 5/8 24

5.83 5.937 5.656

2.416 2 7/8”-8RD EU

7 38

D44-0700-1406 5/8 17-20

5.938 6.135 5.8127 32-35

D44-0700-220 7 26-29 6.136 6.276 5.968D44-0700-240 7 20-26 6.276 6.456 6.078D44-0700-320 7 17-20 6.456 6.578 6.266D44-0700-340 7 5/8 33.7-39 6.579 6.797 6.453D44-0700-420 7 5/8 24-29.7 6.798 7.025 6.672D44-0700-440 7 5/8 20-24 7.025 7.125 6.812D44-0862-120 8 5/8 40-49 7.511 7.725 7.312

3 3 1/2”-8RD EUD44-0862-140 8 5/8 32-40 7.725 7.921 7.531D44-0862-200 8 5/8 20-28 7.922 8.191 7.781D44-0962-120 9 5/8 47-53.5 8.3 8.681 8.218

4 4 1/2”-8RD EU

D44-0962-140 9 5/8 40-47 8.681 8.835 8.437D44-0962-200 9 5/8 29.3-36 8.836 9.063 8.593D44-1075-100 10 3/4 32.7-55.5 9.625 10.192 9.5D44-1075-200 11 3/4 38-60 10.605 11.2 10.5D44-1275-100 12 3/4 48-53 11.75 12.3 11.625D44-1338-200 13 3/8 48-72 12.3 12.715 12

SMT T E N S I O N PAC K E R S

Model SMT Tension Packer is a retrievable, tension set packer, designed to hold pressure from below. This economical tension packer is for shallow wells where sufficient setdown weight is not available to utilize a set down packer. This packer can be used in water flood, oil production or treating applications. They are available for 4” through 13 3/8” casing.

Features:


n Compact, short, easy to transport and run

n Bore is larger than tubing drift diameter

n Easy to operate J-Slot control

n Rocker type slips

n One piece packing

n Three release methods,normal release, Shear release and safety joint top sub


38


SPECIFICATIONS



D43-5010-300 5 15-18 4.25 4.408 4.125 1.81

2 7/8”-8RD EU

D43-5510-300 5 1/2 20.0-23.0 4.625 4.778 4.50 1.94

D43-5510-301 5 1/2 15.5-20.0 4.778 4.95 4.64 1.94

D43-7010-301 7 38 5.83 5.937 5.65 2.38

D43-7010-300 7 32.0-35.0 5.938 6.135 5.81 2.38

D43-7010-302 7 26.0-29.0 6.136 6.276 5.97 2.38

D43-7010-303 7 20.0-26.0 6.276 6.456 6.07 2.38

D43-7010-304 7 17.0-20.0 6.456 6.578 6.27 2.38

SM P P U L L-P U S H TY P E PAC K E R

Model SMP Pull-Push Type Packers are used for testing and zonal isolation application. The packers will be set when uplift and put down and unset by uplifting. It is simple structure and reliable functionally.

Features:



n The length is moderate for running in

n Can be used with hydraulic anchor and circulation calve for formation fracturing

39

S H-2 H Y D R AU L I C SE TT I N G PAC K E R S

SPECIFICATIONS


threadPump-out plug

(in) (lbs/ft) Min(in) Max(in) ( in ) (in)

D31-5000-200 5 15-18 4.276 4.408 4.07 2

2 7/8”-8RD EU D73-2800-200

D31-5500-3005 1/2

15.5-23 4.67 4.95 4.5 1.93

D31-7000-301 9-13 5.044 5.192 4.81 1.93

D31-7000-300

7

38 5.791 5.921 5.68

2.44

D31-7000-302 29-35 5.92 6.184 5.812

D31-7000-303 26-29 6.184 6.454 5.968

D31-7000-304 20-26 6.276 6.184 6.078

D31-7000-311 17-20 6.454 5.578 6.266

D31-7000-310 38 5.791 5.921 5.68

3 3 1/2”-8RD EU D73-3500-200

D31-7000-312 29-35 5.92 6.184 5.812

D31-7000-313 26-29 6.184 6.454 5.968

D31-7000-314 20-26 6.276 6.184 6.078

D31-7600-300 17-20 6.454 5.578 6.266

D31-7600-301

7 5/8

33.7-39 6.579 6.797 6.392.44 2 7/8”-8RD EU

With Pump-out plug

D31-7610-310 20-24 7.025 7.125 6.73

D31-7610-311 33.7-39 6.579 6.797 6.39

3 3 1/2”-8RD EUD31-9600-200 20-24 7.025 7.125 6.73

D31-9600-201 9 5/8

43.5-53.5 8.538 8.755 8.18D73-3500-200

D31-9600-201 36-47 8.681 8.921 8.43

Model SH-2 Retrievable Hydraulic Packers can be run in single or multiple zone installations. It is recommended for deviated wells where conditions are not suitable for mechanical or wireline set packers. No tubing movement is required or generated to set the packer. Once set, the packer is locked in place by one-piece bi-directional slips and will hold high differential pressures. The packer can be released by either straight pull or right-hand tubing rotation. An equalizing and by-pass feature is incorporated in the release mechanism. They are available for 5” through 9 5/8” casing.

Features:


n Recommended for deviated wells

n Tubing pressure actuated


n Straight pull or rotational release

n Bi-directional one-piece slips below the packer

40


SPECIFICATIONS


Connection thread Pump-out plug(in) (lbs/ft) Min(in) Max(in) ( in ) ( in )

D32-0450-100 4.5 9.5-13.5 3.91 4.09 3.77

1.93

2 3/8”-8RD EU 387-5884-543

D32-0500-200 5 15.0-18.0 4.25 4.408 4.13

D32-0500-3005 11.5-15.0

4.408 4.56 4.255.5 26

D32-0550-120 5.5 20.0-23.0 4.625 4.778 4.5

2.00

D32-0550-140 5.5 15.5-20.0 4.778 4.95 4.64

D32-0550-2005.5 13.0-15.5

4.95 5.19 4.786 26

D32-0550-300 6 20.0-23.0 5.191 5.39 5.06D32-0550-400 6 15.0-18.0 5.391 5.56 5.156D32-0550-520 6.625 34 5.561 5.609 5.41D32-0550-540 6.625 28.0-32.0 5.61 5.791 5.484

D32-0662-1406.625 24.0-28.0

5.791 5.921 5.48

2.416 2 7/8”-8RD EU D73-2800-200

7 38

D32-0700-1206.625 24

5.83 5.937 5.667 38

D32-0700-1406.625 17.0-20.0

5.938 6.135 5.817 32.0-35.0

D32-0700-220 7 26.0-29.0 6.136 6.276 5.97D32-0700-240 7 20.0-26.0 6.276 6.456 6.078D32-0700-320 7 17.0-20.0 6.456 6.578 6.27D32-0700-340 7.625 33.7-39.0 6.579 6.797 6.453D32-0700-420 7.625 24.0-29.7 6.798 7.025 6.67D32-0700-440 7.625 20.0-24.0 7.025 7.125 6.812D32-0862-120 8.625 44.0-49.0 7.511 7.687 7.31

3 3 1/2”-8RD EU D73-3500-200

D32-0862-140 8.625 32.0-40.0 7.688 7.921 7.531D32-0862-200 8.625 20.0-28.0 7.922 8.191 7.78D32-0962-120 9.625 47.0-53.0 8.343 8.681 8.21D32-0962-140 9.625 40.0-47.0 8.681 8.835 8.437D32-0962-200 9.625 29.3-36.0 8.921 9.063 8.59

S H F R E T R I E VA B L E D O U B L E-G R I P H Y D R OSTAT I C S I N G L E-ST R I N G PAC K E R

Model SHF Retrievable Hydrostatic Packer is used in production, injection and zonal isolation. It can be run in single or multiple zone installations. It is recommended for deviated wells where conditions are not suitable for mechanical or wireline set packers. No tubing movement is required or generated to set the packer. Once set, the packer is locked in place by one-piece no-directional slips. The packer can be released by straight pull . They are available in 4 1/2” through 9 5/8” casing.

Features:


n Simple operation

n Hydraulically activated, hydrostatic set

n Built-in unloader and bypass

n Pack off is mechanically locked and constantly reinforced by hydrostatic pressure

n Triple seal multi-durometer elements

n No Mandrel movement during setting allows stacked packer applications

n Straight pull release

41

S H C PAC K E R (Y341)

The SHC Packers is used in injection, formation fracturing, acidizing and squeeze cementing. It is hydraulic setting, and can be use solely or with other packers as a combination. Hydraulic anchor is recommended with the string to enhance the stability.

Features:


n Suitable for highly-deviated well.

n Hydraulically activated, hydrostatic set

n Built-in bypass

n Triple seal multi-durometer elements

SPECIFICATIONS


Connection thread(in) (lbs/ft) Min(in) Max(in) ( in ) ( in )

D33-0550-003

5 1/2

20.0-23.0 4.625 4.778 4.5

2 2 7/8”-8RD EUD33-0550-001 15.5-20.0 4.778 4.95 4.64

D33-0550-002 13.0-15.5 4.95 5.19 4.78

D33-0700-001

7

38 5.83 5.937 5.65

2.44 2 7/8”-8RD EU

D33-0700-002 32.0-35.0 5.938 6.135 5.81

D33-0700-003 26.0-29.0 6.136 6.276 5.97

D33-0700-004 20.0-26.0 6.276 6.456 6.07

D33-0700-005 17.0-20.0 6.456 6.578 6.27

42


SPECIFICATIONS


Connection thread(in) (lbs/ft) Min(in) Max(in) (in) (in)

D34-0550-002

5 1/2

20.0-23.0 4.625 4.7784.54.644.78

2 2 7/8”-8RD EUD34-0550-001 15.5-20.0 4.778 4.95

D34-0550-003 13.0-15.5 4.95 5.19

D34-0700-001

7

38 5.83 5.937 5.65

2.44 2 7/8”-8RD EU

D34-0700-002 32.0-35.0 5.938 6.135 5.81

D34-0700-003 26.0-29.0 6.136 6.276 5.97

D34-0700-004 20.0-26.0 6.276 6.456 6.07

D34-0700-005 17.0-20.0 6.456 6.578 6.27

S H H PAC K E R (Y344)

The SHH packer is a hydraulic setting packer, can take out of well by releasing the pressure. They can be used for injection, formation fracturing and acidizing.

Features:

n Multi-stage piston provides enough setting force.

n Multiple packing element ensures seal stability after setting.

n Release after bleed pressure, operation is simplified.

n Suitable for highly-deviated well.

n No tubing operation.

43

STA T U B I N G A N C H O R

Model STA Tubing Anchor/Catchers are used to allow placement of tubing in tension. Vertical tubing movement is prevented which in turn lessens sucker rod tubing wear. Their small o.d. and large i.d. permits larger volume production capacities. These fully retrievable tools can be easily adjusted for emergency release by adding or removing shear pins. They are available for 4 1/2” through 7 5/8” casing.

Features:


n Large bore

n Small OD

n Model “R” right hand release or emergency shear release, Model “L” left hand release or emergency shear release

n Easy adjusted release from 5,000 lbs to 60,000 lbs

n Drag blocks rather than drag springs

SPECIFICATIONS


Connection thread(in) (lbs/ft) Min(in) Max(in) (in) (in)

D08-0450-001(R)4 1/2 9.5-13.5 3.920 4.090 3.75

1.93

2 3/8”-8RD EU

D08-0450-201(L)

D08-0500-201(L)5 13.0-18.0 4.276 4.491 4.00

D08-0500-001(R)

D08-0550-201(L)

5 1/2 13.0-23.0 4.670 5.044 4.50

2.00

D08-0550-001(R)

D08-0550-210(L)

2 7/8”-10RD NUD08-0550-010(R)

D08-0711-201(L)7 23.0-40.0 5.920 6.580 5.50

D08-0700-001(R)

D08-0700-210(L)

7 17.0-38.0 5.920 6.580 5.76

3.00 3 1/2”-8RD EUD08-0700-010(R)

D08-0700-202(L)2.37 2 7/8”-8RD EU

D08-0700-002(R)

R——right hand setting L——left hand setting

44


SPECIFICATIONS

Part numberOD ID Length

Extend length

Con-nection thread

LoadBurst pres-sure

Col-lapse pres-sure

Work-ing pres-sure

Work-ing temp

Shear force

Piston area

in in in in lbs psi psi psi °C lbs In²

D00-2300-301 3.668 2 45 14

2 7/8” EUE

84k 10,796 8,487 8,000 148 6000*3 2.55

D00-2800-305

4.25 2.375

90 60

162k 13,775 12,589

10,000

148 6000*4

3.866

D00-2800-306 101 72

D00-2800-310 150 120

D00-2801-305 90 603 1/2” EUE

177

6000*6

D00-2801-306 101 726000*4

D00-2801-310 150 120

D00-3500-305

5.250 3

90 60

3 1/2” EUE

224k 15,714 13,111148

6000*8 5.495D00-3500-306 101 72

D00-3500-310150 120

D00-3501-310 177

SE J E X PA N S I O N J O I N T

Model SEJ expansion joint is a key accessory to downhole string, which is used for compensation mechanism by the length change of string that caused by internal and external pressure or temperature changes mechanism.

Features:

n Longer seal area, large expansion travel.

n Can transfer torque.

n Adjustable shear force by different shear pins options.

45

SSV-2 STO R M VA LV E

The Storm valve is a combination Back Pressure Valve and Safety Joint that is run above a SMJ-C Storm Packer, in order to provide well control protection during a temporary abandonment of the well, without having to pull the drill pipe. The Storm Valve allows the packers to be set and then permit disconnection and retrieval of the drill pipe and the upper sub of the valve, while at the same time automatically closing the Storm Valve, isolating the drill pipe below the Storm Packer.

Features:

n Can be easily runned by rotating the tubing string which can open and close the valve.

n In emergency situation, the plug can open the drill pipe passage

n It is designed to be used with right hand set compression type packers only.

SPECIFICATIONS

Part numberCasing OD

Guide ringTool OD Tool ID

Connection thread(in) (in) (in)

D77-0962-001

7 5/8 D77-0000-035 6.125

1.75 4 1/2” IF8 5/8 D77-0000-036 7

9 5/8 D77-0000-037 8

13 3/8 D77-0000-038 11.75

D77-0962-010

7 D77-0000-035 5.5

1.75 3 1/2” IF

7 5/8 D77-0000-036 6.125

8 5/8 D77-0000-037 7

9 5/8 D77-0000-038 8

13 3/8 D77-0000-035 11.75

D77-0500-001

5 1/2

NA 3.72

12 7/8”-8RD EU

D77-0550-001D77-0000-057 4.5

D77-0550-010 2 7/8” IF

46


SPECIFICATIONS

Part number

Casing OD Casing Wt Tool OD

Tool ID

LengthWorking Pressure

TempConnection thread(in) (lbs/ft) Min(in) (in)

in lbs/ft in in in in in Mpa °C

D01-5501-300

5 1/215.5-23

4.67 4.95 4.5

2.13 17.5

70

1482 7/8”-8RD EUE

D01-7011-3002.38

14.19 177

*D01-7011-304 16.5 148 2 7/8”-10RD NUE

D01-7011-310

7 26-38 5.92 6.276 5.66

2.44 16.91

177

2 7/8”-8RD EUE*D01-7011-303

D01-7611-3013.13 16.63 3 1/2”-8RD EUE

*D01-7611-304

D01-7611-311

7 5/8

20-29 6.875 7.125 6.46

2.5

17.66 177

2 7/8”-8RD EUE*D01-7611-314

D01-7611-3003 3 1/2”-8RD EUE

*D01-7611-303

D01-7601-310

33.7-39

6.625 6.765

6.13

2.5

17.5 177 2 7/8”-8RD EUED01-7601-310A

*D01-7611-313

6.25

17.5 177 3 1/2”-8RD EUE

D01-7601-310A 19.5 148 3 1/2”FOX PIN

*D01-7611-313 17.5 177 3 1/2”-8RD EUE

NOTE: * CARBIDE INSERTS Type

SPECIFICATIONS

Part numberTool OD Tool ID

Connection threadOn/Off pressure

Type( in ) ( in ) (psi)

D72-5510-300 4.5 2.44 2 7/8”-8RD EU 3,600/6 pin Reverse

D70-5010-300 3.88 2.05 2 7/8”-8RD EU 4,100

OffD70-5010-301 3.88 2.126 2 7/8”-8RD EU 4,100

D70-5510-310 4.5 2 3 1/2”-8RD EU 1,400

D70-5510-311 4.5 2.38 3 1/2”-8RD EU 1,400

D71-5010-300 3.88 1.38 2 7/8”-8RD EU 900

OnD71-5010-301 3.88 0.88 2 7/8”-8RD EU 900

D71-5010-302 4 1.38 2 7/8”-8RD EU 2,900

D71-5510-310 4.5 1.44 3 1/2”-8RD EU 700

SA H H Y D R AU L I C A N C H O R & S C V C I R CU L AT I O N VA LV E

SAH Hydraulic Anchor

Model SAH hydraulic anchors help prevent the tool from being pumped up the hole. These anchors can hold high pressure of 10k psi.

SCV Circulation Valve

Model SCV valve is normally installed above the packers and opened or closed by pumping a dropping ball down.

47

Model SSJ Safety Joint

SPECIFICATIONS (SHEAR RELEASE)

Part numberTool OD Tool ID Release force

Connection thread(in) (in) (lbs)

D90-4237-100 3.063 2 44,000 ~ 62,000 2 3/8”-8RD EU

D90-4287-100 3.69 2.5 44,000 ~ 62,000 2 7/8”-8RD EU

D90-4350-100 4.5 3 44,000 ~ 62,000 3 1/2”-8RD EU

SPECIFICATIONS (LEFT OR RIGHT HAND RELEASE)


Connection thread Release(in) (in)

D02-0000-001 3.063 1.995 2 3/8”-8RD EU

Left handD02-0000-002 3.688 2.441 2 7/8”-8RD EU

D02-0000-003 4.5 3 3 1/2”-8RD EU

D02-0000-007 3.688 2.441 2 7/8”-8RD EURight hand

D02-0000-008 4.5 3 3 1/2”-8RD EU

SPECIFICATIONS (LATCH ANCHOR TYPE)


Connection thread Release(in) (in)

D02-3211-3204.625 2.375

2 7/8”-8RD EU

Right handD02-3211-324 3 1/2”IF

D02-4011-300 5 3 3 1/2”-8RD EU

Note: Different guide ring OD for different casing size.

Pump Out Plug

SPECIFICATIONS

Part numberTool OD ID befor/after

Ball OD Top thread BottomShear force

(in) (in) PSI

D73-2800-200

3.75 1.25/2.25 1.5in 2 7/8”EUE

2 7/8”EUE

(780~830)*6D73-2800-201 half-mule shoe

D73-2800-202 basket end

D73-3500-200

4.50 1.75/2.87 2 3 1/2”EUE

3 1/2”EUE

(900~950)*6D73-3500-201 half-mule shoe

D73-3500-202 basket end

SS J SA F E TY J O I N T & P U M P O U T P LU G

48


SPECIFICATIONS

Part numberSize Tool OD Length

( in ) ( in ) ( in )

D04-4500-000 3 1/2 3 1/2 157.48

D04-5500-000 4 5/16 4 5/16 157.48

D U M P BA I L E R

A variety of dump bailers are for casing applications. The service most frequently performed with these dump bailers is the dumping of sand and/or cement on bridge plugs set in casing.

Features:


n Very light

n The design of dumping cement through the bottom glass striking assures the security of dumping

Note: Inspect screw thread condition before service.

49

The Sur-Grip Vise is a heavy duty screw-type vise designed for holding pipe, valves, fittings, or just about anything within the capacityof its positive grip jaws.

Equipment may be placed in the versatile Sur-Grip from any of three sides with the fourth side acting as a positioning and steadying guide. The unit’s easy rotating handle quickly extends at arm height for extra leverage for critical tightening applications. The Sur-Grip Vise is available in sizes 2”~9 5/8”.

SPECIFICATIONS

Part numberDimension height of vice jaw

( mm ) ( mm )

D06-0962-001 1850×1400×700 920

D06-0962-002 1850×1400×700 670

D06-1338-001 1850×1500×700 800

“C” TY P E S U R-G R I P V I SE

50

COILED TUBING TOOLS

‘TO R CO N N EC T’ E X T E R N A L S L I P CO I L CO N N EC TO R

The ‘Torconnect’ External Slip Connector has been primarily developed to withstand the most extreme high-torque, high-tensile applications.

Unlike existing slip connectors, the ‘Torconnect’ External Slip Connector does not rely on grub screws to transmit torque from the tool string through to the coiled tubing. This feature is provided through a unique non-rotational slip arrangement providing high bi-directional torque resistance. The slip is positively engaged into the bottom sub via drive teeth, therefore transmitting any rotational torque from the tool string directly to the pipe.

Design Features/Benefits:

n High tensile strength

n Non rotational

n Internal pressure seal

n Replaceable slips

SPECIFICATIONS

Part Number

Coiled Tubing Diameter

Max OD Min IDThread

(in) (in) (in)

D97-1125-100 1 1/4 1.687 0.75 1” AMMT

D97-1150-100 1 1/2 2.125 1.001.5”AMMT

D97-1175-100 1 3/4 2.375 1.00

D97-1200-100 2.00 2.875 1.502 3/8” PAC

D97-1237-100 2 3/8 3.125 1.50

D97-1287-100 2 7/8 3.625 1.50 2 7/8” PAC

51

‘S L I M CO N N EC T’ E X T E R N A L S L I P CO N N EC TO R

The ‘Slimconnect’ External Slip Connectors allows the attachment of coiled tubing to the CT Tool Work String via the provision of a threaded connection.

The ‘Slimconnect’, as it’s name suggests, has an O.D. which is smaller than a standard ‘Torconnect’. This enables the ‘Slimconnect’ to be used in operations where a maximum diameter of coiled tubing is required to be run in a minimal I.D. restriction.

The design of the ‘Slimconnect’ utilizes a set of helical ‘wicker’ type slips that grip the tubing in a ‘wedging’ action, thus, an increase in tension results in increased grip.


n High tensile strength for size

n Slimline body O.D.


n Replaceable slips

SPECIFICATIONS

Part Number


Max OD Min IDThread

(in) (in) (in)

D97-1125-102 1 1/4 1.687 0.750 1” AMMT

D97-1150-102 1 1/2 2.1251.000 1.5” AMMT

D97-1175-102 1 3/4 2.375

D97-1200-102 2 2.875 1.5002 3/8” PAC

D97-1237-102 2 3/8 3.125 1.500

52

COILED TUBING TOOLS

‘TO R CO N N EC T’ I N T E R N A L S L I P CO N N EC TO R

Unlike existing slip connectors, the ‘Torconnect’ Internal Slip Connector does not rely on grub screws to transmit torque from the tool string through to the coiled tubing. This feature is provided through a unique non-rotational slip arrangement providing high bi-directional torque resistance. The slip is positively engaged into the bottom sub via drive teeth, therefore transmitting any rotational torque from the toolstring directly to the pipe.

The basic installation to the coiled tubing does not require any specialized tooling or make-up torque. The connector is simply fitted to the pipe and an overpull taken to test and set the connector.

The Internal ‘Torconnect’ also has only 4 main components and includes an enclosed lock nut feature to prevent the connector from being jarred free from the pipe.

Both Internal and External versions of the ‘Torconnect’ Slip Connector feature an interchangeable service connection sub allowing the operator to easily change from one thread connection to another.

Because the ‘Torconnect’ can withstand extremely high tensile and torsional loads, it is ideally suited for high-end CT drilling, milling, under-reaming and fishing applications.

Design Features/Benefits


n Non rotational


n Replaceable slips

SPECIFICATIONS

Part NumberCoiled Tubing Diameter Max OD Min ID

Thread(in) (in) (in)

D97-1150-202 1 1/2*0.125 1.50 0.5001” AMMT

D97-1175-202 1 3/4*0.134 1.75 0.625

D97-1200-203 2*0.175 2.00 0.8121.5”AMMT

D97-1237-201 2 3/8*0.175 2.375 1.000

53

R O L L-O N CO N N EC TO R

Roll-On Connector

The Roll-On Connector allows the attachment of Coiled Tubing to the CT Tool/Work String via the provision of a threaded connection.

The Roll-On Connectors are available to suit all standard sizes of coiled tubing.




n Easy make up

Roll-On Connector Crimping Tool

The Roll-On Connector Crimping tool ensures easy field installation of the Roll-On Connector to the coiled tubing.

The crimping tool has two interchangeable wheels, one of which is used to swage the coiled tubing onto the Roll-On Connector. The other is a cutting wheel which can be used to cut the coiled tubing.

SPECIFICATIONS

Part Number


Max OD Min ID PressureTensile Strength Thread

Crimping Tool Part Number

(in) (in) (in) Psi Lbs

D97-1125-300 1 1/4*1/8 1.500 0.50

10,000

25,000 1” AMMT

D97-1150-301

D97-1150-300 1 1/2*1/8

1.500 0.75 35,000 1”AMMTD97-1150-304 1 1/2*0.102

D97-1150-305 1 1/2*0.109

D97-1150-306 1 1/2*0.156

D97-1175-300 1 3/4*1/81.750 0.75

45,0001” AMMT

D97-1175-304 1 3/4*0.175

D97-1175-303 1 3/4*0.175 2.125 1.00 1.5” AMMT

D97-1200-300 2*0.188

2.000 1.00

65,000

1.5” AMMTD97-1200-301 2”*0.145” 60,000

D97-1200-303 2”*0.175” 65,000

D97-1200-304 2”*0.156” 60,000

D97-1237-300 2 3/8”*0.175” 2.375” 1.00 60,000 1.5” AMMT

54

COILED TUBING TOOLS

D O U B L E E N D E D R O L L-O N CO N N EC TO R

Double Ended Coiled Tubing Roll-On Connectors allow the inline attachment of two lengths of coiled tubing.

Double Ended Roll-On Connectors have the same outside diameter as the coiled tubing.

Double Ended Roll-On Connectors attach to the coiled tubing’s internal diameter. The connector is secured by crimping the tubing into the connectors preformed channels with a Roll-On Connector Crimping Tool.




n Easy make up

SPECIFICATIONS

Part Number


Max OD Min ID PressureTensile Strength Crimping Tool Part

Number (in) (in) (in) Psi Lbs

D97-1125-302 1 1/4*1/8 1 1/4 0.500 10,000 23,000

D97-1150-301

D97-1125-303 1 1/4*0.109 1 1/4 0.500 10,000 16,000

D97-1150-302 1 1/2*1/8 1 1/2 0.750 10,000 25,000

D97-1150-308 1 1/2*0.134 1 1/2 0.750 10,000 32,000

D97-1175-305 1.75 *0.156 1.75 0.750 10,000 38,000

D97-1200-302 2*0.175 2 1.000 10,000 45,000

D97-1200-305 2 *0.156 2 1.000 10,000 42,000

D97-1237-302 2 3/8*0.175 2 3/8 1.500 10,000 65,000

55

D I M P L E/G R U B S C R E W CO N N EC TO R

The Grub Screw/Dimple Connector allows the attachment of coiled tubing to the CT Tool/Work String via the provision of a threaded connection.

The connector is attached to the coiled tubing by grub screws that engage in preformed dimples in the tubing wall.

The dimples are formed by using the Dimple Hammer/Extractor Tool that places the indents in identical positions to the screws on the connector.

The Dimple/Grub Screw/ Connectors have ‘o’ ring pressure seals as standard and are also available with ‘v’ packings as an option to create the pressure seal.




n Easy make up

n High Torque

SPECIFICATIONS

Part Number


Max OD Min IDThread

Dimple Hammer / Extrator Tool Part Number

(in) (in) (in)

D97-1125-400 1 1/4 1.750 0.687 1” AMMT D97-1125-401

D97-1150-400 1 1/2 2.125 1.0001.5” AMMT

D97-1150-401

D97-1175-400 1 3/4 2.375 1.000 D97-1175-401

D97-1200-400 2 2.875 1.500 2 3/8” PAC D97-1200-401

D97-1237-400 2 3/8 3.125 1.500 2 3/8” PAC D97-1237-401

56

COILED TUBING TOOLS

P U L L P L AT E F O R CO I L CO N N EC TO R

The Pull Plate is used as an accessory with the Coil Tubing Connector. Once the Connector is installed on the coil, install the Pull Plate on to the connector.

This will allow the connector to enter the lubricator but the bottom of the pull plate will seat on the end of the lubricator, preventing further travel. Now apply the proper overpull to test the connector. The pull plate also prevents the connector from being pulled against the seals of the lubricator.

After a successful pull test, remove the pull plate and proceed with installing the remainder of the tool string. The pull plate can also be built with 3/16” hole and a ½” tap for a needle and be used also as a test plug.

SPECIFICATIONS

Part NumberMax OD Min ID

Thread(in) (in)

D97-1125-110 5 0.75 1” AMMT

D97-1150-110 5 1.00 1.5”AMMT

D97-1237-110 6 1.50 2 3/8”PAC

D97-1238-110 6 1.50 2 3/8”REG

D97-1287-110 6 1.50 2 7/8”PAC

57

D UA L F L A P P E R C H EC K VA LV E

The Dual Flapper Check Valve is used in situations where the operator wishes to eliminate the flow or potential flow of fluids back through the work string while running or retrieving pipe under pressure.

The Dual Flapper Check Valve is designed so that the flow area through the valve is equal to or greater than the cross sectional area of I.D. of the valve seat. The Dual Flapper Check Valves are easy to assemble or disassemble, a new flapper cartridge can be inserted in a matter of minutes. The Dual Flapper Check Valve combines reliability, minimum flow restrictions, and the ability to pump wiper plugs or to drop balls through the valve for disconnects, etc.

As with ball type check valves, rust, scale, paraffin, dried hydrocarbons or materials do not pose a threat of plugging this flapper check valve due to the ability to pump through the valve at all times.

The flapper valve and seat are directly exposed to the pumped fluid and some errosion may occur on the seat surface and possibly the flapper valve itself, depending on a variety of factors including velocity through the valve, abrasiveness of the fluid pumped, solids content, and duration of the exposure. The flappers and valve seats should be checked and replaced when required.

SPECIFICATIONS


Thread(in) (in)

D96-5150-100 1.500 0.620

1” AMMTD96-5168-100 1.687 0.687

D96-5175-100 1.750 0.687

D96-5212-100 2.125 0.891

1.5” AMMTD96-5225-100 2.250 1.031

D96-5237-100 2.375 1.000

D96-5287-100 2.875 1.3692 3/8” PAC

D96-5312-100 3.125 1.442

D96-5312-102 3.125 1.442 2 3/8” EUE

D96-5387-101 3.875 2.125 2 7/8” EUE

58

COILED TUBING TOOLS

T W I N F L A P P E R C H EC K VA LV E W I T H LO C K-O U T S L E E V E

The Twin Flapper Check Valve with Lock-Out Sleeve is a coiled tubing string component that can be run in the locked out position and activated with a drop ball when required to perform as a downhole safety barrier. Its use provides a means of preventing the back flow of well fluids into the coiled tubing in the event of failure or damage to the coiled tubing string or surface equipment.

The design of the Twin Flapper Check Valve incorporates a dual sealing system in each flapper assembly for increased safety. A teflon seat provides the primary low pressure seal, while at higher pressure the flapper seals on a metal to metal arrangement.

It is ideally suited to CT velocity string systems allowing activation by a drop ball prior to pulling the string from the well.


n Dual sealing in each flapper cartridge i.e. low pressure Teflon seat/seal and high pressure full metal to metal seat/seal

n Full bore fluid passage for balls, darts & plugs

n Removable flapper cartridges

n Simple drop ball activation

SPECIFICATIONS

Part NumberMax OD Min ID Ball OD


D96-5175-300 1.750 0.470 5/8 1” AMMT

D96-5218-300 2.187 0.750 13/161.5”AMMT

D96-5287-300 2.875 1.000 1 1/16

D96-5312-300 3.125 1.000 1 1/16 2 3/8”REG

D96-5350-300 3.500 1.375 1 1/2 2 7/8”PAC

59

BA L L C H EC K VA LV E

The Ball Check Valve is a standard coiled tubing string component. Its use in a tool string provides a means of preventing the back flow of fluids into the coiled tubing in the event of failure or damage to the surface equipment.

Ball Check Valves are used when devices such as balls and darts do not need to pass through the valve. In the event of a ball or dart needing to be dropped a Flapper Valve must be used.


n Large flow area

n Easy redress

n Metal to metal sealing

SPECIFICATIONS


Thread(in) (in)

D96-5168-200 1.687 0.750 1” AMMT

D96-5212-200 2.125 1.000

1.5” AMMTD96-5225-200 2.250 1.031

D96-5237-200 2.375 1.031

D96-5287-200 2.875 1.3752 3/8” PAC

D96-5312-200 3.125 1.500

60

COILED TUBING TOOLS

H E AV Y D U TY H Y D R AU L I C D I S CO N N EC T

SPECIFICATIONS

Part NumberMax OD Min ID Ball OD Max Ball OD

Fishing neck Thread(in) (in) (in) (in)

D97-1150-500 1.500 0.438 1/2 3/8 1.5”GS

1” AMMTD97-1168-500 1.6870.468

5/8 7/16

2”GSD97-1175-500 1.750

D97-1212-500 2.125 0.531

2 1/2”GS

1.5” AMMT

D97-1212-502 2.125 0.531 1.9” AMMT

D97-1225-500 2.2500.782 13/16 3/4 1.5” AMMT

D97-1237-500 2.375

D97-1287-500 2.875 0.875 15/16 13/16 3”GS2 3/8” PAC

D97-1312-500 3.125 1.299 1 3/8 1 3/16 3.5”GS

D97-1312-502 3.125 1.299 1 3/8 1 3/16 3.5”GS 2 3/8” EUE

D97-1387-501 3.875 1.875 2 1 13/16 4”GS 2 7/8” EUE

The Heavy Duty Hydraulic Disconnect (HDHD) allows the tool string to detach at a predetermined point via the deployment of a suitable drop/trip ball through the coiled tubing. The drop ball locates on a piston sleeve creating sufficient back pressure to shear the pins and disconnect the tool. The piston sleeve pushes the tool apart to ensure a clean disconnect. Circulation is immediately returned to the tool string, providing a surface indication of a positive disconnect. All piston sleeves and drop balls are returned to surface leaving a standard ‘GS’ internal fish neck for retrieval purposes.

The ‘HDHD’ utilizes a heavy duty, one piece, threaded collet slip to hold the tool together. The collet slip endures higher tensile loading than collet finger type release mechanisms and is far less susceptible to fatigue. The collet slip is backed up with a collet slip sleeve to give maximum tensile strength to the disconnect during heavy jarring operations. Only by dropping a ball and shearing the pins can the collet sleeve shift, allowing the collet and top sub to part. The piston sleeve is pressure balanced, therefore internal pressure does not affect the hydraulic configuration and shear values.

High torque capabilities are achieved through positive torque drive teeth between the top sub and the main body of the tool. The ‘HDHD’ is therefore ideally suited for high torque, heavy duty coiled tubing drilling operations where maximum performance and durability is essential.

Shear screws can be supplied in either brass or steel to give a comprehensive pressure range to suit virtually any coiled tubing application. Shear screws are also integrally situated to eliminate the possibility of shear screws vibrating free during CT drilling operations.

By interchanging the piston sleeve, the drop/trip ball size can be varied to suit the desired tool string requirements. This is a particularly useful feature when the ‘HDHD’ is situated below jars and accelerators, and ID restrictions are a factor for consideration. Running the ‘HDHD’ below jars and accelerators ensures that if disconnection of the tool string is necessary, a greater proportion of the tool string is safely returned to surface.

A major design consideration is that of simple field redress. The ‘HDHD’ has been designed to ensure assembly & disassembly of the tool is trouble free. No special assembly tools are required and all seals are standard ‘o’ rings.

61

S H E A R R E L E A SE J O I N T

The Shear Release Joint allows the parting of the coiled tubing work string by applied predetermined tension.

The Shear Release Joint was designed for and used primarily in cement stinger operations as a simple effective emergency release.

The Shear Release Joint incorporates shear screws that can be used in various combinations to allow a wide range of predetermined shear settings.

The released part of the Shear Release Joint can be retrieved using a ‘GS’ type Pulling Tool.


n Simple design

n On location adjustable settings


n Internal ‘GS’ type fish neck after release

n Torque Thru capability

SPECIFICATIONS


Fishing neck Thread(in) (in)

D97-1168-700 1.6870.500 2”GS 1” AMMT

D97-1175-700 1.750

D97-1212-700 2.250 0.750

2 1/2”GS

1.5” AMMT

D97-1212-703 2.250 0.750 1.90”NU

D97-1237-700 2.375 1.000 1.5” AMMT

D97-1287-700 2.875 1.250 3”GS2 3/8” PAC

D97-1312-700 3.125 1.500 3.5”GS

D97-1375-701 3.750 2.125 4”GS 2 7/8”EUE

62

COILED TUBING TOOLS

DUAL ACTIVATED CIRCULATION VALVE (DROP BALL/OVER PRESSURE)

The Dual Activated Circulation Valve offers the traditional method of returning circulation of the tool string through use of a drop ball. In addition, the valve is capable of operating through internal overpressure within the tubing string.

Conventional dual circulation valves use a burst or rupture disc to facilitate the function of returning circulation through overpressure. However, the Dual Activated Circulation Valve offers a pressure differential activated piston. The piston activation pressure can be predetermined at surface through shear pins, offering superior flexibility and considerable savings on redress.

As with many other tools in the standard BHA tool range, the emphasis is on simplicity and the Dual Activated Circulation Valve has very few component parts, seals and thread connections.


n Simple drop ball design and pressure differential to operate

SPECIFICATIONS

Part Number

Max OD Min ID Length Per shear pin

Threadin in in

Drop ball pressure PSi

Over pres-sure PSi

D96-6168-200 1.687 0.406 7.500 940-1090 2620-30301” AMMT

D96-6175-200 1.750 0.406 7.500 940-1090 2620-3030

D96-6212-200 2.125 0.406 8.500 650-750 2140-2460

1.5” AMMTD96-6225-200 2.250 0.625 8.500 590-670 1560-1800

D96-6237-200 2.375 0.625 8.500 590-670 1560-1800

D96-6287-200 2.875 0.812 9.500 316-358 830-9602 3/8” PAC

D96-6312-200 3.125 0.812 9.500 316-358 830-960

63

B U R ST D I S C C I R CU L AT I O N S U B

The Burst Disc Circulation Sub is a standard coiled tubing tool string component that is used in conjunction with tools that require drop balls etc., and that need to be circulated into the coiled tubing.

The Burst Disc Circulation Sub is incorporated into the coiled tubing tool string just below the tool that requires a drop ball.

Should circulation be lost due to a down hole restriction, a predetermined pressure applied to the coil will burst the disc in the sub and re-establish circulation.


n Various burst disc pressure rating available

SPECIFICATIONS

Part NumberMax OD Min ID Burst disc pressure

Thread(in) (in) (PSI)

D96-6168-300 1.6870.406

Optional

1” AMMTD96-6175-300 1.750

D96-6212-300 2.125 0.8751.5” AMMT

D96-6237-300 2.375 1.000

D96-6287-300 2.875 1.2502 3/8” PAC

D96-6312-300 3.125 1.250

64

COILED TUBING TOOLS

ST R A I G H T BA R

The Straight Bar provides a means of extending the tool string, while maintaining the maximum through bore. The tubular section between the top & bottom sub can be interchanged to vary the length of the straight bar. This approach offers an ideal way of spacing out tools within the tool string, without compromising the flow requirements of flow activated or jetting tools.


n Full flow through bore

n Solid construction

SPECIFICATIONS


Thread(in) (in)

D97-3168-000 1.687

0.500

1” AMMTD97-3175-000 1.750

D97-3212-000 2.1251.5” AMMT

D97-3225-000 2.250

D97-3287-080 2.875 1.0002 3/8” PAC

D97-3312-000 3.125 1.250

65

D OW N-ST R O K E I N T E N S I F I E R

The Down-Stroke Intensifier is used in conjunction with the Down-Stroke Hydraulic Jar.

Its purpose is to provide the necessary even pull and acceleration power for the Coiled Tubing Down-Stroke Hydraulic Jar to operate efficiently, especially in long reach wells where there is limited coiled tubing push.

The Coiled Tubing Down-Stroke Intensifier stores downward energy in a powerful compression spring, which is suddenly released when the Hydraulic Jar ‘releases’, thus intensifying the downward jarring impact.

The Down-Stroke Intensifier is fully vented to the well bore to prevent damping effect and has full ‘pump through’ capability, compatible with the PCE Coiled Tubing Hydraulic Jar

The Down-Stroke Intensifier is manufactured from high grade low alloy steel and stainless steel and is extremely robust and durable in construction.

Under normal conditions the Down-Stroke Intensifier will function at temperatures of up to 200°C if circulation is maintained during operations.



n Heavy duty construction

SPECIFICATIONS

Part NumberMax OD Min ID Load to close

Thread(in) (in) Lbs

D97-4175-100 1.750 0.375

614

1” AMMT

D97-4212-100 2.1250.500 1.5” AMMT

D97-4225-100 2.250

D97-4287-100 2.8750.625 650 2 3/8” PAC

D97-4312-100 3.125

66

COILED TUBING TOOLS

U P-ST R O K E I N T E N S I F I E R

The Up-Stroke Intensifier is used in conjunction with the Up-Stroke Hydraulic Jar.

Its purpose is to provide the necessary even pull and acceleration power for the Coiled Tubing Up-Stroke Hydraulic Jar to operate efficiently, especially at shallow depths where there is limited coiled tubing stretch.

The Coiled Tubing Up-Stroke Intensifier stores upward energy in a powerful compression spring, which is suddenly released when the Hydraulic Jar ‘releases’, thus intensifying the upward jarring impact.

The Up-Stroke Intensifier is fully vented to the well bore to prevent damping effect and has full ‘pump through’ capability, compatible with the CT Hydraulic Jar.

The Up-Stroke Intensifier is manufactured from high grade low alloy steel and stainless steel and is extremely robust and durable in construction.

Under normal conditions the Coiled Tubing Up-Stroke Intensifier will function at temperatures of up to 200°C if circulation is maintained during operations.




SPECIFICATIONS

Part NumberMax OD Min ID Load to close

Thread(in) (in) Lbs

D97-4175-400 1.750 0.375

614

1” AMMT

D97-4212-400 2.1250.500 1.5” AMMT

D97-4225-400 2.250

D97-4287-400 2.8750.625 650 2 3/8” PAC

D97-4312-400 3.125

67

D OW N-ST R O K E H Y D R AU L I C J A R

The Down-Stroke Hydraulic Jar (DSHJ) provides the means for repeatable, controlled downward jarring when required during coiled tubing operations.

The ‘DSHJ’ has a highly dependable closed and balanced hydraulic system for hydrostatic pressure. This allows the coiled tubing operator to control the intensity of the jarring action to suit the field application, by applying a sustained downward load, which can be infinitely variable, according to the usage application.

The ‘DSHJ’ is normally used in conjunction with the CT Down-Stroke Intensifier. It is suitable for most coiled tubing applications where the deployment of downhole service and manipulation tools is required, including setting and pulling plugs, gas lift valves, opening and shutting sliding side doors and the general fishing of downhole retrievables.

The ‘DSHJ’ is also used in most standard coiled tubing tool strings during other coiled tubing services such as swabbing, jetting, logging, and stimulating, especially in deviated wells, where there is a possibility of the tool string becoming stuck. The closed hydraulic system prevents contamination from well bore fluids thus giving greater operational dependability. Under normal conditions the ‘DSHJ’ will function at temperatures of up to 100°C if circulation is maintained during operations. The ‘DSHJ’ is manufactured from high grade low alloy steel and stainless steel and is extremely robust and durable in construction.



n Specifically designed for CT use

n Efficient Valve Seating for deviated applications

n Closed & balanced hydraulic system

n Also available with ‘Torque Thru’ capability

SPECIFICATIONS


Thread(in) (in)

D97-4175-200 1.7500.375 1” AMMT

D97-4181-200 1.810

D97-4212-200 2.1250.500 1.5” AMMT

D97-4225-200 2.250

D97-4287-200 2.875 0.7502 3/8” PAC

D97-4312-200 3.125 1.000

68

COILED TUBING TOOLS

U P-ST R O K E H Y D R AU L I C J A R

The Up-Stroke Hydraulic Jar (USHJ) provides the means for repeatable, controlled upward jarring when required during coiled tubing operations.

The ‘USHJ’ has a highly dependable closed and balanced hydraulic system for hydrostatic pressure. This allows the coiled tubing operator to control the intensity of the jarring action to suit the field application, by applying a sustained downward load, which can be infinitely variable, according to the usage application.

CT ‘USHJ’s’ are normally used in conjunction with the coiled tubing Up-Stroke Intensifier. It is suitable for most coiled tubing applications where the deployment of downhole service and manipulation tools is required, including setting and pulling plugs, gas lift valves, opening and shutting sliding side doors and the general fishing of downhole retrievables.

CT ‘USHJ’s’ are also used in most standard ct tool strings during other coiled tubing services such as swabbing, jetting, logging, and stimulating, especially in deviated wells, where there is a possibility of the tool string becoming stuck. The closed hydraulic system prevents contamination from well bore fluids thus giving greater operational dependability. Under normal conditions the ‘USHJ’ will function at temperatures of up to 100°C, if circulation is maintained during operations. ‘USHJ’s’ is manufactured from high grade low alloy steel and stainless steel and is extremely robust and durable in construction.



n Specifically designed for CT use

n Efficient Valve Seating for deviated applications

n Closed & balanced hydraulic system

n Also available with ‘Torque Thru’ capability

SPECIFICATIONS


Thread(in) (in)

D97-4175-500 1.7500.375 1” AMMT

D97-4181-500 1.810

D97-4212-500 2.1250.500 1.5” AMMT

D97-4225-500 2.250

D97-4287-500 2.875 0.7502 3/8” PAC

D97-4312-500 3.125 1.000

69

R OTO-H A M M E R I M PAC T D R I L L J A R

The Roto-Hammer is a tool that transmits multiple downward impact forces at high frequency when fluid is pumped through it, thus eliminating the need to cycle the coil. The tool operates through a combination of layoff weight and controlled flow activation through the tool-string, converting flow and pressure into mechanical energy.

Applications:

n Under balanced & over balanced clean outs

n Shifting stubborn sliding sleeves

n Breaking ceramic & glass discs

n Swaging collapsed tubing & screens

n Broaching operations

n Driving debris downhole

n Scale clean out including: cement, resin coated sand, plastic, barium, calcium & iron

SPECIFICATIONS

Part NumberTool OD

Operating Pres-sure

Pump RateSet Down Weight Thread

(in) (psi) (L/min) (lbs)

D97-4168-300 1.687 500-2500 37.8-158.7 500-1800 1”AMMT

D97-4212-300 2.125 500-2500 37.8-264.6 500-2850 1.5”AMMT

70

COILED TUBING TOOLS

H Y D R AU L I C U P/D OW N J A R S

The Hydraulic Up/Down Jars use a piston (metering device) and oil to create a time delay. This time delay allows energy to be stored in stretched tubing. Once the energy is stored, the jar piston bypasses (step), creating a hammer-and-anvil effect that imparts an impact load to the end of the tool assembly. As the jar is pulled in tension, a piston moves through a restricted bore containing oil. This process enables the system to store energy and the continued upward pull moves the piston over the step, which releases the stored energy and allows the mass to rapidly accelerate to the top of its stroke. This process creates an impact force that can be twice as great as the tension that can be pulled on the tubing alone. The force supplied depends upon the force applied at the tool. The Hydraulic Up/Down Jars can be supplied either up acting, down acting or bi-directional.


n Jar is shorter than most hydraulic jars

n Higher impact capability, it can hit harder than any other jar of the same size

n Maximum operating temperature 500 degrees F

n Large bore for drop ball

n Jar has high tensile strength for higher impact service capability

n Jar is hydrostatic pressure balanced

n Jar can be run in compression or tension

SPECIFICATIONS

Part NumberMax OD Min ID Max overpull Max overpush

Torsional yield strength

Total stroke Thread

(in) (in) (lbs) (lbs) (lbs) (in)

D97-4168-900 1.687 0.56 10000 10000 950 12 1”AMMT

D97-4212-900 2.125 0.75 18000 15000 2000 12 1.5”AMMT

D97-4287-900 2.875 1.00 34000 20000 2700 12 2 3/8”PAC

D97-4312-900 3.125 1.25 45000 35000 3100 12 2 3/8”REG

71

H Y D R AU L I C U P/D OW N I N T E N S I F I E R S

SPECIFICATIONS


MAX detent working load

MAX lift load after jarring

Tensile strength

Free stroke-up Thread

(in) (in) (N) (lbs) (lbs) (in)

D97-4168-900 1.687 0.56 33360 50000 70500 5 1”AMMT

D97-4212-900 2.125 0.75 44480 100000 135000 5 1.5”AMMT

D97-4287-900 2.875 1.00 115650 200000 250000 7 5/8 2 3/8”PAC

D97-4312-900 3.125 1.25 133440 280000 325000 4 5/8 2 3/8”REG

The Hydraulic Up/Down Intensifiers is a double acting accelerator used to increase the impact effect of the Hydraulic Up/Down Jars. The Intensifiers stores concentrated energy in an optimal position in the Jar string. It helps to absorb impact shock waves that travel up the drill pipe allowing the drill string to be utilized closer to their yield loads. This permits higher pull loads to be placed on the hydraulic drilling jars. The Intensifiers provides the operator the ability to perform impact operation at or near the surface. The compressibility provides the necessary “stretch” to operate the Jarring equipment. The Intensifiers supplies drive for the concentrated weights in the jars string in the same manner as the long resilient drill string. It is an efficient reservoir for storing energy since its stretch is confined to a short tool length. The increased efficiency and stretch provides a much harder hitting Jar system and increases the impact up to approximately a factor of three and can impact at much higher impacts depending on conditions. It will work on any drill string and provides a means to get higher impact load in a crooked or extended reach well, where drag is a significant factor. The Intensifiers /Jar system should be placed as close to the stuck point as possible. The impact effect diminishes as the distance increases between the intensifiers and the Jar and the stuck point.


n Higher intensifiers capability, it can hit harder than any other jar/ Intensifiers of the same size

n Maximum operating temperature 500 degrees F

n Large bore for drop ball

n Intensifiers has high tensile strength for higher impact service capability

n Intensifiers can be run in compression or tension

72

COILED TUBING TOOLS

F LU T E D CE N T R A L I Z E R

The Fluted Centralizer is designed to be included as part of the coiled tubing work string to assist in providing centralization to allow easier location of tools during fishing or to provide general stability in the tubing.

The Fluted Centralizer has a full flow through bore allowing passage of darts or drop balls and is available in any specific length.



n Solid one piece construction

SPECIFICATIONS


Thread(in) (in)

D97-6225-310 2.2500.750

1” AMMT

D97-6268-310 2.677

1.5” AMMTD97-6275-310 2.7501.000

D97-6300-310 3.000

D97-6350-310 3.500

1.500 2 3/8” PAC

D97-6375-310 3.750

D97-6400-310 4.000

D97-6425-310 4.250

D97-6450-310 4.500

73

B OW SP R I N G CE N T R A L I Z E R

The Bow Spring Centralizer provides a fast and effective method of attaching centralizers to a tool string. This approach allows several centralizers to be attached to a coiled tubing tool string without adding any significant length to the string.

By simply positioning the Centralizer Carrier Subs in the tool string, the Bow Spring Centralizers can be placed in the optimum position to centralize the string.

The tool is specifically designed to allow worn or damaged bowsprings to be changed without removing the whole centralizer assembly. Also, the centralizer assemblies can be removed without breaking out the string.

The upper centralizer sleeve is anchored to the tool string via retainer pins. The lower centralizer sleeve is allowed to ride freely up and down the tool string as the bowsprings compress and expand. This ensures the minimum of interference as the tool string passes through restrictions in the tubing.

SPECIFICATIONS


Thread(in) (in)

D97-6168-100 1.687 0.625 1” AMMT

D97-6212-101 2.1250.730 1.5” AMMT

D97-6212-100 2.250

D97-6287-100 2.8751.250 2 3/8” PAC

D97-6312-100 3.125

74

COILED TUBING TOOLS

F LOW AC T I VAT E D B OW SP R I N G CE N T R A L I Z E R

The Flow Activated Bow Spring Centralizer is designed to allow tool strings or parts of tool strings to be centralized in the tubing/casing for various operations.

The Flow Activated Bow Spring Centralizer is designed so that it’s bow springs are normally retracted. The bow springs only expand when a pressure differential is achieved across the tool. This enables the centralizer to pass, for example, through the restricted bores of the tail pipe and expand into the casing liner below without any unnecessary wear on the bow springs.

As a safety precaution, the bow springs are mounted above a coil spring. This is to allow the bow springs the necessary movement they require in order to pass through a restricted bore whilst still expanded.



n Safety feature which allows bow springs movement when meeting restrictions in expanded condition, therefore preventing bow spring damage

SPECIFICATIONS


Expansion Range Thread(in) (in)

D97-6168-201 1.6870.450 1 11/16”-6 1/2” 1” AMMT

D97-6168-200 1.810

D97-6212-200 2.1250.750

2 1/8”-7”

1.5” AMMTD97-6225-200 2.250 2 1/4”-7”

D97-6270-200 2.700

0.937

2 3/4”-8 1/2”

D97-6287-200 2.875 2 7/8”-8 1/2”2 3/8” PAC

D97-6312-200 3.125 3 1/8”-8”

75

TO R Q U E T H R U K N U C K L E J O I N T

The Torque Thru Knuckle Joint, when incorporated between the jars and the manipulation tool, will provide additional flexibility in the tool string. This additional flexibility is often necessary when the bore of the hole the tool is running through is restricted and/or highly deviated. The Torque Thru Knuckle Joint can be used when rotation of the tool string is not required, for example, coiled tubing drilling applications.

The Coiled Tubing Knuckle Joint provides full 15° angular deviation and internal pressure sealing throughout the full deviation of the tool. The ball and socket of the knuckle have a key that prevents rotation but still allows full angular movement.

The full flow through bore also allows the use of flow activated tools below the Knuckle Joint. Multiple coiled tubing torque thru knuckle joints can be incorporated in particularly long tool strings.




n 15° angular deviation

n Torque Thru capability

SPECIFICATIONS


Thread(in) (in)

D97-3168-200 1.6870.531 1” AMMT

D97-3175-200 1.750

D97-3212-200 2.125 0.594

1.5” AMMTD97-3225-200 2.2500.750

D97-3237-200 2.375

D97-3312-200 2.8751.270 2 3/8” PAC

D97-3312-200 3.125

76

COILED TUBING TOOLS

C. A .R.S. A .C ‘H T’ CO N N EC TO R

The C.A.R.S.A.C. HT is designed to assist with the tubing ‘make-up’ where it is difficult to rotate the tools to engage threads and is particularly suited for long tool string applications. It is especially useful when utilized in conjunction with integral ball valves and deployment bars.


n Anti-rotation

n High Tensile/High Torque

n Self-aligning

n Easy stabbing/easy break-out

SPECIFICATIONS


Thread(in) (in)

D97-3168-300 1.6870.500 1” AMMT

D97-3175-300 1.750

D97-3212-300 2.125 0.875

1.5” AMMTD97-3225-300 2.2501.000

D97-3237-300 2.375

D97-3287-300 2.8751.250 2 3/8” PAC

D97-3312-300 3.125

D97-3450-300 4.500 1.500 2 7/8” PAC

77

SW I V E L J O I N T

The Swivel Joint is a standard tool string component which when used, permits full rotation of the BHA made up below the joint.

The Swivel’s design includes integral sealed bearings which ensure full integrity of flow through the joint.

The inclusion of a Swivel Joint in a typical BHA gives the operator orientation flexibility. A CT Swivel Joint in a BHA will allow the tool string to be broken and made-up below the joint without the need to disconnect from the coil.

The Swivel Joint is necesary where tool sting orientation is required such as in the running and pulling of gas lift mandrels.


n Full range of sizes available

n Sealed bearings for integrity of flow

n Maximum flow area

SPECIFICATIONS


Thread(in) (in)

D97-3168-400 1.687 0.340 1” AMMT

D97-3212-400 2.125 0.6871.5” AMMT

D97-3237-400 2.375 0.750

D97-3287-400 2.8751.125 2 3/8” PAC

D97-3312-400 3.125

78

COILED TUBING TOOLS

LO C K I N G SW I V E L J O I N T

The Locking Swivel Joint was designed to allow the assembly of long coil tubing strings with minimum lubricator length. Many times it is necessary to have long lengths of lubricator to accommodate the tool string, creating a difficult and dangerous situation.

Now with the Locking Swivel Joint, it allows for sections of the tool string to be made up and lowered into the well bore. The String is spaced out and a pup joint is inserted, allowing the pup joint to seal in the rams of the BOP. The Locking Swivel is placed on top of the section of tools and dropped in the lubricator. Pull the coupling back and tighten the set screws, allowing the clutches to disengage and letting the swivel free spin.

The other section of tool string can now be assembled. Before lowering the swivel in the hole, loosen the set screws so the coupling can slide back down, engaging the clutches. If rotation is required in the tool string, simply take the brass drive pins out from under the coupling and this will prevent any back torque through the string. If run below the motor the clutches must be engaged and brass drive pins installed.

SPECIFICATIONS


Thread(in) (in)

D97-3168-500 1.687 0.5311” AMMT

D97-3175-500 1.750 0.560

D97-3212-500 2.1250.812 1.5”AMMT

D97-3225-500 2.250

D97-3287-500 2.875 1.000 2 3/8”PAC

D97-3312-500 3.1251.500 2 7/8”PAC

D97-3350-500 3.500

79

M OTO R H E A D A SSE M B LY

SPECIFICATIONS


Thread(in) (in)

D96-1168-200 1.687

0.4061” AMMT

D96-1175-200 1.750

D96-1212-200 2.1251.5” AMMT

D96-1237-200 2.375 0.625

D96-1287-200 2.875 0.7502 3/8” PAC

D96-1312-200 3.125 0.812

The Motorhead Assembly (M.A) has been developed in recognition to industry demands for compact, heavy duty, integrated BHA components. The M.A combines the Double Flapper Check Valve with the Heavy Duty Hydraulic Disconnect and the Dual Circulation Valve, standard components for virtually all tool string designs. The tubing connector has been deliberately eliminated to give the added flexibility of operator choice for the connector type and coil tubing size.

The M.A. provides the operator with a compact, versatile, upper BHA and offers the following features:

n The M.A’s compact design gives an overall length saving of approximately 30% over the use of conventional individual components.

n The high torque capability of the M.A. provides the ideal Motorhead for today’s high demand coiled tubing drilling applications.

n The choice of tubing connector is not dictated by the M.A., therefore giving the operator the flexibility to choose the most appropriate connector to suit the application.

n With a considerable reduction in the number of component parts, seals and thread connections, the M.A. is uncomplicated to assemble/disassemble and inexpensive to redress.

80

COILED TUBING TOOLS

M OTO R

A positive displacement drilling motor that uses hydraulic horsepower of the drilling fluid to drive the drill bit. Mud motors are used extensively in directional drilling and coiled tubing operations and can be assemble with a variety of power section to meet the customers well conditions. From hot holes to harmful power fluids such as drilling mud or nitrogen. When ordering specify these parameters to provide the best power section do the job quickly and get the most life out of your motors.

SPECIFICATIONS

Part NumberMax OD

Lobe StageFlow rate

Working torque

Rotory speedThread

(in) L/min N.m R/min

D96-1169-100 1.687 5:6 5.0 90-210 280 390-8601”AMMT

D96-1169-101 1.687 5:6 3.0 90-170 180 400-720

D96-1212-100 2.125 5:6 6.0 80-190 430 260-6401 1/2”AMMT

D96-1212-101 2.125 5:6 2.5 110-230 350 200-400

D96-1287-100 2.875 5:6 4.0 90-380 890 100-420

2 3/8”PACD96-1287-101 2.875 7:8 4.5 190-470 1045 140-360

D96-1312-100 3.125 5:6 3.5 380-660 1450 230-390

81

G S’ R U N N I N G/P U L L I N G TO O L S

The ‘GS’ Type Running/Pulling Tool is designed to run and retrieve downhole tools with conventional internal fish necks. The latching mechanism is a robust dog/core design which releases positively from the internal fish neck when a hydraulic differential is applied to the tool.

The tool does not require shear pins or drop balls since the differential required to activate the tool is provided by circulating through a choke insert in the core.

‘GS’ Type Running/Pulling Tools are available for all standard internal fish neck sizes.

Features/Benefits:

n Full hydraulic operation

n Multiple latch & release capability

n Proven dog/core design

n Available to catch internal fish necks from 2” to 7”

n Safety shear function

SPECIFICATIONS

Part NumberSize Max OD Min ID Internal fishneck

Thread(in) (in) (in) (in)

D96-3200-300 2 1.810 0.250 1.375 1” AMMT

D96-3250-300 2 1/2 2.250

0.390

1.8121.5” AMMT

D96-3300-300 3 2.720 2.312

D96-3350-300 3 1/2 3.110 2.6252 3/8” PAC

D96-3400-300 4 3.620 3.312

82

COILED TUBING TOOLS

“J D C”R U N N I N G/P U L L I N G TO O L S

SPECIFICATIONS

Part NumberSize Max OD Min ID Internal fishneck

Thread(in) (in) (in) (in)

D96-3200-100 2 1.875

0.390

1.375 1” AMMT

D96-3250-100 2 1/2 2.300 1.750 1.5” AMMT

D96-3300-100 3 2.875 2.3122 3/8” PAC

D96-3400-100 4 3.750 3.125

The “JDC” Running/Pulling Tool is a collet type running/pulling tool designed to run or retrieve downhole tools that have conventional external fishing necks.

The running/pulling tool design is extremely robust in construction and allows a full 360° engagement of the fishing neck to be latched.

The tool is fully hydraulically activated and therefore does not require the use of shear pins or drop balls to operate, since this is achieved by circulating through a choke in the core of the tool.

Features/Benefits:

n Full hydraulic operation


n Available to catch all standard external fish necks

83

F LOW AC T I VAT E D S H I FT I N G TO O L S

The Flow Activated Shifting Tools is designed to be used as a work tool for opening and closing sliding sleeves.

The normally closed shifting tool is flow activated and therefore does not require the use of drop balls to activate it. The Flow Activated Shifting Tools by design can be used to either open or close sliding sleeves.

Shifting Tools are supplied with a ‘pin-pin’ crossover, enabling the tool to be run shifting either up or down.

The Flow Activated Shifting Tools are available to suit all sizes and makes of sliding sleeves and can be supplied with either positive or selective keys.

Features/Benefits:

n Flow activated (No drop balls required)

n Positive or selective key options

n Optional external fish neck

SPECIFICATIONS

Part NumberSSD size Min ID

Thread(in) (in)

D96-4231-100 2.313

0.390 1.5” AMMTD96-4256-100 2.562

D96-4275-100 2.750

D96-4281-100 2.813

D96-4312-100 3.125 0.500

2 3/8” PACD96-4331-100 3.313 0.437

D96-4343-100 3.437 0.500

D96-4368-100 3.688 0.4372 7/8” PAC

D96-4381-100 3.813

0.500D96-4412-100 4.125

3 1/2” PACD96-4431-100 4.313

D96-4456-100 4.562

84

COILED TUBING TOOLS

D O U B L E E N D E D SE L EC T I V E S H I FT I N G TO O L S

The Double Ended Selective Shifting Tool (DESST) has been designed specifically to selectively shift PCE, Otis, Camco, Baker sliding sleeves (SSD’s) in horizontal well bores.

The DESST shifting keys are normally retracted during the running operation and are hydraulically flow activated to the open shift position by increasing surface pump volume and therefore, pressure at the downhole location of the DESST and SSD.

The DESST can selectively open or close multiple SSD’s in a single coiled tubing trip.

Features/Benefits:


n Dual action for opening or closing sliding sleeves

n Positive or selective key options


SPECIFICATIONS

Part NumberSSD size Min ID

Thread(in) (in)

D96-4231-200 2.313

0.390 1.5” AMMTD96-4256-200 2.562

D96-4275-200 2.750

D96-4281-200 2.813

D96-4312-200 3.125 0.500

2 3/8” PACD96-4331-200 3.313 0.437

D96-4343-200 3.437 0.500

D96-4368-200 3.688 0.4372 7/8” PAC

D96-4381-200 3.813

0.500D96-4412-200 4.125

3 1/2” PACD96-4431-200 4.313

D96-4456-200 4.562

85

T U B I N G A N C H O R S

The Coiled Tubing Anchor provides a fixed anchor point within the tubing to assist in the performance of other coiled tubing downhole tools. The Coiled Tubing Anchor also can be supplied in a double unit for increased holding forces.

The Coiled Tubing Anchor is a flow activated tool. Increasing the flow at surface generates a back pressure at the tool. This back pressure activates the slip mechanism and the slips are set against the tubing wall. Once set, the anchor can withstand large axial loads, subject to the tool size and application.

The Anchor can be re-set at another location within the tubing string by reducing coiled tubing pressure. The slips are then able to retract away from the tubing wall and release the tool string. Once the tool string has been moved to a new location the slips can again be set with the application of pressure. This operation can be repeated as many times as required in a single deployment.

Features/Benefits:

n Completion Tubing Cutting where coil motors need to be stationary for knives to be effective.

n Production Logging Surveys to hold coiled tubing deployed survey tools rigidly and to dampen vibration caused by high production flow rates.

n Accurate spotting of well treatments where changes in flow pressures can cause the end of coiled tubing to move significantly.

SPECIFICATIONS

Part NumberTubing size Max OD

Thread(in) (in)

D98-5237-100 2 3/8 1.750 1” AMMT

D98-5287-100 2 7/8 2.1801.5” AMMT

D98-5350-100 3 1/2 2.720

D98-5450-100 4 1/2 3.625 2 3/8” PAC

86

COILED TUBING TOOLS

T U B I N G CU TT E R

The Tubing Cutter is a tool designed to go through small restrictions in tubing and cut larger I.D. tubing below.

Blades are designed to extend from piston force created with hydraulic pressure.

The tubing cutter is extremely important where wireline tools and mechanical tools have failed.

SPECIFICATIONS

Part NumberMax OD Rotory speed Weight on bit Max cut OD

Top thread(in) RPM BLS (in)

D96-8170-100 1.700 70-120 0-2,000 5 1”AMMT

D96-8212-100 2 1/8 70-120 0-2,000 51.5”AMMT

D96-8237-100 2 3/8 70-110 0-3,000 7

D96-8287-100 2 7/8 70-110 0-3,000 8 1/4 2 3/8”PAC

D96-8350-100 3 1/2 70-110 0-4,000 9 2 7/8”REG

D96-8425-100 4 1/4 70-110 0-4,000 9 3 1/2”REG

87

M I L L S

Mills used for mill out all kinds of obstacles and debris in well bore.

SPECIFICATIONS

Part NumberMax OD

Blade number Top thread(in)

D08-2810-000 2.28 / 1”AMMT

D08-4510-105 3.50 3 2 3/8”IF

D08-4510-106 3.50 3 2 3/8”PAC

D08-4510-114 3.62 5 2 3/8”PAC

D08-5510-106 4.33 3 2 3/8”PAC

D08-5510-118 4.21 5 2 3/8”PAC

D08-5510-105 4.33 3 2 3/8”IF

D08-7010-000 5.51 / NC38

88

COILED TUBING TOOLS

R OTA R Y J E T WA S H TO O L S

The Rotary Jet Wash Tool is designed to be used for both jetting and circulating operations when cleaning and washing the inside of the tubing. It can also be used to assist in the manipulation of the coiled tubing string both in and out of the well.

The design of the Rotary Jet Wash Tool works on the principal of applied fluid pressure causing the nozzle to rotate and jet the fluid against the tubing wall in a full 360° rotating action.

Features/Benefits:

n Forward and reverse jetting

n Numerous jetting options

n Simple design

SPECIFICATIONS

Part NumberMax OD

Thread(in)

D96-7168-500 1.6871” AMMT

D96-7175-500 1.750

D96-7212-500 2.1251.5” AMMT

D96-7237-500 2.375

D96-7287-500 2.8752 3/8” PAC

D96-7312-500 3.125

89

SP I N N I N G WA S H TO O L

The Spinning Wash tool is a self-rotating swivel designed for coil tubing well service. The powerful rotating jets cover a large area for efficient cleaning. Jet reaction force powers rotation of the head.

The standard nozzle sleeve has 13 ports; seven forward, and 6 backwards. Some of the ports may be plugged in a balanced pattern to concentrate the flow in a particular direction.

Whether your deposits are paraffin, asphaltine, hydrates, calcium carbonate, barium sulfate, corrosion products, or mineral scale – the Spinning Wash tool is ready to restore production.

SPECIFICATIONS

Part NumberMax OD

Nozzle size Thread(in)

D96-7168-200 1.687 3/16”*5 1” AMMT

D96-7212-200 2.125 7/32”* 4+1/4”1.5” AMMT

D96-7237-200 2.375 1/4”*5

D96-7287-200 2.8755/16*5 2 3/8” PAC

D96-7312-200 3.125

90

COILED TUBING TOOLS

F LOW AC T I VAT E D H Y D R AU L I C J E TT I N G I N D E X I N G TO O L S

The Flow Activated Hydraulic Jetting Indexing Tool is designed to rotate jetting wash nozzles, to allow full 360° bore coverage.

The Jetting Indexing Tool is rotated in a controlled 45° or 60° incremental manner by applying intermittent surface pump pressure.

When flow pressure is increased to the index operating pressure, the lower half of the tool strokes downwards and indexes. Maintaining the pressure then allows the increased flow to jet through the jetting wash nozzle. When the flow pressure is decreased the tool strokes back and completes the indexing cycle. By repeating this operation a full 360° wash cycle can be achieved.

A range of jetting nozzles can be supplied with the Jetting Indexing Tool, for more detail.

Features/Benefits:


n Low pressure actuation

n Full bore opening for high pressure rates

n Easy to operate

n Simple construction

n 6 x 60° or 8 x 45° rotation options available

SPECIFICATIONS


Thread(in) (in)

D97-5168-500 1.687 0.375 1” AMMT

D97-5212-500 2.125” 0.500” 1.5” AMMT

D97-5287-500 2.875 1.000”2 3/8” PAC

D97-5312-500 3.125 1.000”

91

N OZ Z L E O PT I O N S

SPECIFICATIONS

Part Number Nozzle type Max OD Min ID Nozzle Configuration Part Number Nozzle type Max OD Min ID Nozzle Configuration

D96-7168-100

Single Port Flow Thru Nozzle

1.687” 0.250” 1x0.250” D96-7168-110

Multiple Back Flow Port Nozzle

1.687” 0.250”1x0.250” 4x0.250”@45°

D96-7212-100 2.125” 0.500” 1x0.500” D96-7212-110 2.125” 0.250”1x0.250” 4x0.250”@45°

D96-7237-100 2.375” 0.750” 1x0.750” D96-7237-110 2.375” 0.312”1x0.312” 4x0.312”@45°

D96-7312-100 3.125” 0.875” 1x0.875” D96-7312-110 3.125” 0.375”1x0.375” 4x0.375”@45°

D96-7168-120

Multiple Side Flow Port Nozzle

1.687” 0.250” 4x0.250”@90° D96-7168-130

Multiple Flow Port Nozzle

1.687” 0.250”1x0.250” 4x0.250”@135°

D96-7212-120 2.125” 0.250” 4x0.250”@90° D96-7212-130 2.125” 0.250”1x0.250” 4x0.250”@135°

D96-7237-120 2.375” 0.312” 4x0.312”@90° D96-7237-130 2.375” 0.312”1x0.312” 4x0.312”@135°

D96-7312-120 3.125” 0.375” 4x0.375”@90° D96-7312-130 3.125” 0.375”1x0.375” 4x0.375”@135°

D96-7168-140

Multiple Up Flow Port Nozzle

1.687” 0.250”1x0.500” 4x0.187”@45° 4x0.187”@90°

D96-7168-150

Single Flow Port Muleshoe Nozzle

1.687” 0.625” 1x0.625”@45°

D96-7212-140 2.125” 0.250”1x0.500” 4x0. 250”@45° 4x0. 250”@90°

D96-7212-150 2.125” 0.875” 1x0.875”@45°

D96-7237-140 2.375” 0.312”1x0.625” 4x0.312”@45° 4x0.3127”@90°

D96-7237-150 2.375” 0.875” 1x0.875”@45°

D96-7312-140 3.125” 0.375”1x0.750” 4x0.375”@45° 4x0.375”@90°

D96-7312-150 3.125” 1.000” 1x1.000”@45°

Single Port Flow Thru Nozzle

Multiple Back Flow Port Nozzle

Multiple Side Flow Port Nozzle

Multiple Flow Port Nozzle

Multiple Up Flow Port Nozzle

Single Flow Port Mule-shoe Nozzle

92

COILED TUBING TOOLS

F LOW AC T I VAT E D R E L E A SA B L E F I S H I N G/B U L L D O G SP E A R S

The Flow Activated Releasable Fishing/Bulldog Spear is a variable catch internal spear used to retrieve a lost cylindrical fish from the well bore.A complete range of slips is available for each size tool. To operate simply run into the fish and set down weight, pick up, and retrieve the fish.To release from the fish simply set down weight, circulate in conjunction with a Hydraulic Sequencing Tool above the spear. The spear will then release due to the flow created differential.A complete range of hardened slips are available for each size tool. See table for slip and catch size details.

Features/Benefits:n Flow or drop ball activatedn Hardened & double tempered slipsn Robust constructionn Variable slip sizes for each tool

SPECIFICATIONS

Part NumberMax OD Min ID Catch Range


D98-4200-300 1.850” 0.250 1 3/8”-1 1/2” 1” AMMT

D98-4250-300 2.250”

0.390

2”-2 1/8”1.5” AMMT

D98-4300-300 2.625” 2 1/4”-2 3/8”

D98-4350-300 3.110” 2 5/8”-2 3/4” 2 3/8” PAC

D98-4400-300 3.625” 3 1/8”-3 1/2” 2 7/8” PAC

RELEASABLE FISHING/BULLDOG SPEAR SLIPS

Nominal Size

2” 2 1/2” 3” 3 1/2” 4”

Max OD 1.850” 2.250” 2.625” 3.110” 3.6”

Nominal Slip Size

Catch Range Catch Range Catch Range Catch Range Catch Range

1 1/8” 1 1/8”-1 1/4” - - - -

1 1/4” 1 1/4”-1 3/8” - - - -

1 3/8” 1 3/8”-1 1/2” - - - -

1 1/2” 1 1/2”-1 5/8” -- - - -

1 5/8” 1 5/8”-1 3/4” - - - -

2” - 2-2 1/8” - - -

2 1/8” - 2 1/8”-2 1/4” -- - -

2 1/4” - 2 1/4”-2 3/8” -2 1/4”-2 3/8” - -

2 3/8” - 2 3/8”-2 1/2” 2 3/8”-2 1/2” - -

2 1/2” - - 2 1/2”-2 5/8” - -

2 5/8” 2 5/8”-2 3/4” 2 5/8”-2 3/4”

2 3/4” 2 3/4”-2 7/8” 2 3/4”-2 7/8”

2 7/8” 2 7/8”-3”

3” 3”-3 1/8”

3 1/8” 3 1/8”-3 1/4”

3 1/4” 3 1/4”-3 3/8”

3 3/8” 3 3/8”-3 1/2”

3 1/2” 3 1/2”-3 5/8”

3 5/8” 3 5/8”-3 3/4”

93

F LOW AC T I VAT E D R E L E A SA B L E OV E R S H OTS

The Flow Activated Releasable Overshot is a variable catch external overshot used to retrieve a lost cylindrical fish from the well bore.The Flow Activated Releasable Overshot operates in the same way as a standard non-releasable overshot. The tool is run in hole until it latches on the fish and butts out. Pulling up will cause the slips to set into the fish.Should the fish be irretrievable, the tool can be released from the fish by flow activation and returned to surface.The Flow Activated Releasable Overshot can be used to fish lost or broken tubing, coil and also coiled tubing tools that have backed off down hole.The Flow Activated Releasable Overshot can be supplied to overshoot and seal onto a specific fish in order to form a pressure tight seal. This is of importance if there is a flow activated tool beneath the fish that requires operation before the fish can be retrieved.

Features/Benefits:n Internal hammer action assists releasen Flow or drop ball activatedn Hardened & double tempered slipsn Robust constructionn Variable slips sizes for each tooln Optional bell guides available

SPECIFICATIONS

Part NumberMax OD Min ID Catch Range


D98-4200-400 1.850 0.250 15/16-1 1/16 1” AMMT

D98-4250-400 2.250

0.390

1 7/16-1 9/161.5” AMMT

D98-4300-400 2.625 1 7/16-2 1/16

D98-4350-400 3.250 2-2 3/16

2 3/8” PACD98-4400-400 3.800 2 3/8-2 5/8

D98-4450-400 4.250 2 7/8”-3 1/8”

SPECIFICATIONS

Nominal Size 2” 2 1/2” 3” 3 1/2” 4”

Max OD 1.850” 2.250” 2.625” 3.250” 3.800”

Nominal Slip Size Catch Range Catch Range Catch Range Catch Range Catch Range

1/2” 7/16”-9/16” 7/16”-9/16” 3/8”-9/16” - 3/8”-5/8”

5/8” 9/16”-11/16” 9/16”-11/16” 9/16”-3/4” 1/2”-11/16” -

3/4” 11/16”-13/16” 11/16”-13/16” - 11/16”-7/8” 5/8”-7/8”

7/8” 13/16”-15/16” 13/16”-15/16” 3/4”-15/16” - -

1” 15/16”-1 1/16” 15/16”-1 1/16” 15/16”-1 1/8” 7/8”-1 1/16” 7/8”-1 1/8”

1 1/8” 1 1/16”-1 3/16” 1 1/16”-1 3/16” - 1 1/16”-1 1/4” -

1 1/4” 1 3/16”-1 5/16” 1 3/16”-1 5/16” 1 1/8”-1 5/16” - 1 1/8”-1 3/8”

1 3/8” 1 5/16”-1 7/16” 1 5/16”-1 7/16” 1 5/16”-1 1/2” 1 1/4”-1 7/16” -

1 1/2” 1 7/16”-1 9/16” 1 7/16”-1 9/16” - 1 7/16”-1 5/8” 1 3/8”-1 5/8”

1 5/8” - 1 9/16”-1 11/16” 1 1/2”-1 11/16” - -

1 3/4” - 1 5/8”-1 3/4” 1 11/16”-1 7/8” 1 5/8”-1 13/16” 1 5/8”-1 7/8”

1 7/8” -- - - 1 13/16”-2” -

2” - - 1 7/8”-2 1/16” 2”-2 3/16” 1 7/8”-2 1/8”

2 1/4” - - -- 2 1/8”-2 5/16” 2 1/8”-2 3/8”

2 1/2” - - - - 2 3/8”-2 5/8”

2 3/4” - - - - 2 5/8”-2 7/8”

94

COILED TUBING TOOLS

R O P E SP E A R

The Rope Spear is efficient for removal of wireline, electric line, or braided line that has been left in the wellbore.

SPECIFICATIONS

Part Number Tubing Top thread

D98-4237-200 2 3/8” 1”AMMT

D98-4287-200 2 7/8”1.5”AMMT

D98-4350-200 3 1/2”

D98-4450-200 4 1/2” 2 3/8”PAC

95

F I S H I N G G R A B S

The Fishing Grab is a tool used to retrieve wire that has broken in the tubing.

The Fishing Grab consists of a box up connection in a housing with either two or three flexible prongs extending downwards. Pointed barbs are welded to the inside of the prongs so as to form hooks that will catch the looped end of the broken line. The Coiled Tubing Fishing Grab also has a large flow through bore.

When a line breaks below the stuffing box, a full gauge such as a slotted skirt wirefinder is normally used to both locate and ball up the broken end of the line before running the Fishing Grab. The Fishing Grab is flexible enough to bend and can be gauged for the tubing it is to be run in. The prong ends of the grab should fit snugly against the walls of the tubing to help prevent line bypass.

Features/Benefits

n Flow through facility

n Simple flexible design

n Robust construction

n External fish neck available

SPECIFICATIONS

Part Number Tubing Top thread

D98-4237-201 2 3/8” 1”AMMT

D98-4287-201 2 7/8”1.5”AMMT

D98-4350-201 3 1/2”

D98-4450-201 4 1/2” 2 3/8”PAC

96

COILED TUBING TOOLS

V E N T U R I J U N K BA S K E TS

The Venturi Junk Basket is a tool which is used to retrieve junk and debris out of the well bore. When fluid is pumped through the string of the coiled tubing and out through the nozzles in the venturi chamber, a vacuum is created in the venturi chamber. Fluid is sucked from the bottom of the tool exit back through the venturi tubes. Most of this fluid mixes with the pressurised fluid to be re-circulated around the bottom of the tool.

The tool is essentially a high powered vacuum cleaner that may be used with fluid, nitrogenated fluids or gases. The nozzles in the tool are simply changed out for the available pump rate, fluid or gas. A debris filter screen is placed before the venturi chamber to prevent debris from blocking the venturi tubes.

A hollow magnetic section with a finger type trap catches junk and debris, which is then carried from the well inside the tool.

Barrel extensions are available to increase the volume of junk which may be carried.

The tool is not dependant on hole size to work, so for example you could use a 38” o.d. tool to retrieve debris from 7” casing.

SPECIFICATIONS

Part NumberMax OD Number of

Venturi Noz-zles

Injection Nozzles Avail-able Thread

(in) (in)

D98-4168-100 1.687 10.062; 0.0780.094; 0.1090.125; 0.1400.156; 0.1710.187

1” AMMT

D98-4206-100 2.062 2

1.5” AMMTD98-4212-100 2.125 2

D98-4262-100 2.625 3

D98-4312-100 3.125 3 2 3/8” PAC

97

L E A D I M P R ESS I O N B LO C KS & H I G H P OW E R E D M A G N E T

Lead Impression Blocks

The Lead Impression Block is an adapted standard wireline service tool used to obtain impressions of foreign objects in the tubing string to assist in identification of the object and thus selection of the correct fishing tool.

The Lead Impression Blocks are available in a range of sizes.

Features/Benefits:

n ’Wash out’ prevention sleeve

n Easily refillable


SPECIFICATIONS

Part NumberMax OD

Thread(in)

D98-7180-100 1.800 1” AMMT

D98-7230-100 2.250

1.5” AMMTD98-7230-100 2.323

D98-7275-100 2.750

D98-7287-100 2.875

2 3/8” PACD98-7350-100 3.500

D98-7448-100 4.488

High Powered Magnet

The High Powered Magnet is used to retrieve small objects, such as metal fragments, balls, small slips, springs, small tools and any other objects that have a magnetic attraction.

SPECIFICATIONS

Part NumberMax OD

Thread(in)

D98-7150-200 1.5001” AMMT

D98-7175-200 1.750

D98-7212-200 2.125

1.5” AMMTD98-7225-200 2.250

D98-7250-200 2.500

D98-7275-200 2.750

D98-7287-200 2.875 2 3/8” PAC

98

COILED TUBING TOOLS

T U B I N G N I P P L E LO C ATO R S

The Tubing Nipple Locator is designed to locate nipples in the tubing while downhole coiled tubing operations are being performed. This makes the tool ideal for depth correlation by tagging a known datum in the production tubing.

The Nipple Locator can be positioned virtually anywhere in the Bottom Hole Assembly. As the Nipple Locator is purely mechanical, the operation of the tool does not require any hydraulic pressure to operate.

The Nipple Locator is run below the nipple to the desired position. A slow pick up will then allow the dogs to tag the back of the nipple profile. A small overpull (approximately 600-900lbs) will be seen on the weight indicator.

This procedure may be repeated indefinitely ensuring that the datum points can be re-checked, therefore a constant indication can be determined.

If a more positive indication is required, the Nipple Locator has the added feature of a shear pin sub. By pinning the shear sub with predetermined shear pins, the Nipple Locator can be configured to allow a significant increase in overpull.

This more positive surface indication of depth correlation can permit an overpull of up to 5000lbs, this operation is however a one-shot operation and once the pins are sheared, the Nipple Locator reverts back to the conventional 600-900lbs repeatable overpulls.

The Nipple Locator comprises of a spring loaded dog assembly which provides a reliable and repeatable means of tagging a range of common nipples within a specific tubing size. All springs are encapsulated minimizing the risk of mechanical tool failure from debris ingress.

SPECIFICATIONS

Part NumberMax OD Min ID Nipple Size


D97-7187-100 1.930 1.750 1.87X1”AMMT

D97-7187-101 1.930 1.750 1.87XN

D97-7231-100 2.380 2.175 2.31X

1.5AMMT

D97-7231-101 2.380 2.175 2.31XN

D97-7275-100 2.900 2.620 2.75X

D97-7275-101 2.900 2.620 2.75XN

D97-7281-100 2.900 2.620 2.81X

D97-7281-101 2.900 2.620 2.81XN

D97-7381-100 3.900 3.600 3.81X2 3/8PAC

D97-7381-101 3.900 3.600 3.81XN

99

CO L L A R STO P

The Collar Stop is designed to locate in the collar recess of API upset and non-upset tubing. The depth can be measure buy the value change of the load.

SPECIFICATIONS

Part Number Casing sizeID Length Load

Thread(in) (in) T

D99-1287-100 2 7/8”6.5# 0.813 13 1 1 1/2”AMMT

D99-1450-100 4 1/2” 9.5-11.6#

1.500

16.875 2

2 3/8”P.A.C

D99-1550-100 5 1/2” 15.5-20# 17.92 2

D99-1550-101 5 1/2” 15.5-20# 17.92 1

D66-5510-001 5 1/2” 20-23# 17.92 2

D66-5510-002 5 1/2” 23-26# 17.92 2

D99-1700-100 7” 26-29# 19.26 2

100

FLOW CONTROL TOOLS

X P R O F I L E N I P P L E

The Model “X” Profile Nipple offers an expanded versatility to downhole selection. Any desired number of “X” Nipples can be placed in the production string, thereby offering an unlimited number of positions for setting and locking surface controls.

Applications:

n Land blanking plugs to shut in well or to test the production tubing.

n Land Velocity Type Safety Valves.

n Land equalizing check valves.

n Land circulating blanking plugs.

n Land chokes to reduce surface flowing pressures.

n Land instrument hangers with geophysical devices such as pressure and temperature recorders.

SPECIFICATIONS

Part NumberSize OD Seal Bore Pressure

Threadin. in. in. psi.

D90-2150-110 1.900 2.20 1.500

10,000

1.90” EUE

D90-2187-110 2.375 2.75 1.875 2 3/8” EUE

D90-2231-110 2.875 3.30 2.313 2 7/8” EUE

D90-2275-1103.500 4.00

2.7503 1/2” EUE

D90-2281-110 2.813

101

X N P R O F I L E N I P P L E

The Model “XN” Profile Nipple is a BOTTOM NoGo Nipple that provides for the location of various wireline flow control devices in the production string.

Applications:







n Restricted I.D. catches tools dropped during wireline work.

SPECIFICATIONS

Part NumberSize OD Seal Bore NoGo ID Pressure

Threadin. in. in. in psi.

D90-2150-210 1.900 2.20 1.500 1.448

10,000

1.90”EUE

D90-2187-210 2.375 2.75 1.875 1.791 2 3/8” EUE

D90-2231-210 2.875 3.30 2.313 2.205 2 7/8” EUE

D90-2275-2103.500 4.00

2.750 2.6353 1/2” EUE

D90-2281-210 2.813 2.666

102

FLOW CONTROL TOOLS

F P R O F I L E N I P P L E

The Model “F” Profile Nipple is a TOP NoGo Nipple that provides for the location of various wireline flow control devices in the production string.

Applications:







SPECIFICATIONS

Part NumberSize OD Seal Bore Pressure

Threadin. in. in. psi.

D90-2150-310 1.900 2.500 1.500

10,000

1.90” EUE

D90-2178-310

2 .375 3.063

1.781

2 3/8” EUED90-2181-310 1.812

D90-2187-310 1.875

D90-2225-3102 .875 3.668

2.2502 7/8” EUE

D90-2231-310 2.312

D90-2275-3103.500 4.500

2.7503 1/2” EUE

D90-2281-310 2.812

103

R P R O F I L E N I P P L E

The Model “R” Profile Nipple is a BOTTOM NoGo Nipple that provides for the location of various wireline flow control devices in the production string.

Applications:







n Restricted I.D. catches tools dropped during wireline work.

SPECIFICATIONS

Part NumberSize OD Seal Bore NoGo ID Pressure

Threadin. in. in. in psi.

D90-2150-410 1.900 2.500 1.500 1.447

10,000

1.90” EUE

D90-2178-410

2 .375 3.063

1.781 1.728

2 3/8” EUED90-2181-410 1.812 1.760

D90-2187-410 1.875 1.822

D90-2225-4102 .875 3.668

2.250 2.1972 7/8” EUE

D90-2231-410 2.312 2.259

D90-2275-4103.500 4.500

2.750 2.6973 1/2” EUE

D90-2281-410 2.812 2.759

104

FLOW CONTROL TOOLS

X O/X D C I R CU L AT I N G S L E E V E

The “XO/XD” Circulating Sleeve provides a convenient way to establish or shut off communication between the tubing and the annulus. Any number of these sleeves may be run in a tubing string, and any or all of them may be opened or closed in one run by standard wireline methods.

Design Features:

n Features a nipple profile above and a packing bore above and below the communication ports.

n Ports can be closed without leaving any obstructions in the tubing once the shifting operation is completed.

n The Model “B” Shifting Tool is used to open (jarring down) or close (jarring up) the “XO/XD” Circulating sleeve.

XO CIRCULATING SLEEVE

Part NumberSize OD Seal Bore Pressure Port Area

Threadin. in. in. psi. in²

D90-7187-201 2.375 3.063 1.875 7,000 1.804 2 3/8” EUE

D90-7231-201 2.875 3.668 2.313 7,000 2.405 2 7/8” EUE

D90-7275-2013.500

4.275 2.750 7,000 4.4543 1/2” EUE

D90-7281-201 4.290 2.813 7,000 4.454

XD CIRCULATING SLEEVE



D90-7187-301 2.375 3.063 1.875 7,000 2.761 2 3/8” EUE

D90-7231-301 2.875 3.668 2.313 7,000 4.201 2 7/8” EUE

D90-7275-3013.500

4.275 2.750 7,000 5.9393 1/2” EUE

D90-7281-301 4.290 2.813 7,000 6.210

105

X A C I R CU L AT I N G S L E E V E

The “XA” Circulating Sleeve provides a convenient way to establish or shut off communication between the tubing and the annulus. Any number of these sleeves may be run in a tubing string, and any or all of them may be opened or closed in one run by standard wireline methods.

Design Features:

n Features a nipple profile above and a packing bore above and below the communication ports.

n Ports can be closed without leaving any obstructions in the tubing once the shifting operation is completed.

n The Model “B” Shifting Tool is used to open (jarring up) or close (jarring down) the ‘ XA” Circulating sleeve.

SPECIFICATIONS



D90-7187-401 2.375 3.063 1.875 7,000 1.804 2 3/8” EUE

D90-7231-401 2.875 3.668 2.313 7,000 2.405 2 7/8” EUE

D90-7275-4013.500

4.275 2.750 7,000 4.4543 1/2” EUE

D90-7281-401 4.290 2.813 7,000 4.454

106

FLOW CONTROL TOOLS

T-2 O N-O F F TO O L

The T-2 On-Off Tool is a tubing disconnect device that has an internal blanking plug locking profile with seal bore for utilizing flow control equipment. The Overshot has a box looking up which connects to tubing string and a pin looking down off the Stinger which connects to the packer. The T-2 On-Off Tool has two basic components that comprise the Overshot. The Top Sub which contains two bonded rubber steel seals and the Jay Latch which has a J Slot configuration to locate and latch the On—Off Tool Stinger. The Jay Latch also has a wash over shoe configuration which allows cutting through debris. The Overshot automatically Jays up on the Stinger when lowered into well.

Applications:

n Item is designed to isolate a lower zone or to disconnect the tubing without releasing or disturbing the packer.

n Standard left hand release

n Automatic jay up

n Bonded seals

n All nipple profiles available for stinger

n Full open or solid stinger available

n 10K rated

n Wash over shoe on all models

SPECIFICATIONS

Part Number(without shear pin)

Part Number(with shear pin)

Casing ODOD Of Stinger

Tension Pressure Thread

in. in. in. lbs. psi. in.

D90-5237-604 D90-5237-504 4.5 3.750 2.60965,000

10,000

2 3/8” EUE

D90-5237-605 D90-5237-505 5.5 4.500 2.609 2 3/8” EUE

D90-5287-605 D90-5287-505 5.5 4.500 3.25075,000

2 7/8” EUE

D90-5287-607 D90-5287-507 7 5.875 3.250 2 7/8” EUE

Note: Right hand turn for connect, left hand turn for disconnect.

107

P X & P X N P LU G

PX Plug

The PX Plug is a device capable of holding pressure differentials from above or below when set at any X Profile Nipple of the same size.

PXN Plug

The PXN Plug is a device capable of holding pressure differentials from above or below when set at any XN Profile Nipple of the same size.

SPECIFICATIONS

Part NumberTubing Size Seal OD NoGo OD Pressure

in. in. in. psi.

D91-6187-200 2.375 1.875 1.865

10,000D91-6231-200 2.875 2.313 2.302

D91-6275-2003.500

2.750 2.740

D91-6281-200 2.813 2.802

SPECIFICATIONS


in. in. in. psi.

D91-6187-201 2.375 1.875 1.865

10,000D91-6231-201 2.875 2.313 2.302

D91-6275-2013.500

2.750 2.740

D91-6281-201 2.813 2.802

108

FLOW CONTROL TOOLS

X & XN LOCK MANDREL PX / PXN EQUALIZING PRONG AND VALVE

X Lock Mandrel

The “X” Lock Mandrel is a selective set lock designed to be landed and locked, down-hole, in a “X ‘ Profile Nipple. Equalizing Sub Assemblies and a variety of sub—surface flow control devices may be attached to this lock mandrel before running.

XN Lock Mandrel

The “XN” Lock Mandrels are similar to the “X” except for the locking keys. The keys for the “XN” Mandrels are chamfered so they will pass through a “X” Profile Nipple uphole. This allows the “XN” Mandrel and flow control to be lowered through “X” Profile Nipples in the tubing string to land in a “XN” Profile Nipple which is always installed in the lower end or on bottom of the tubing string. The NoGo shoulder of the “XN” Lock Mandrel is located on the flow control device.

PX / PXN Equalizing Prong and Valve

The PX/PXN Equalizing Prong and Valve assembly, when attached to an X or XN Lock Mandrel Assembly, converts the lock mandrel to a plug, with equalizing device, capable of holding pressure differentials from above or below.

X/XN LOCK MANDREL

XN Model Part NumberSize ID

X Model Part Numberin. in.

D91-6187-203 1.875 1.38 ‐D91-6187-202

D91-6231-203 2.313 1.81 ‐D91-6231-202

D91-6275-203 2.750 2.31 ‐D91-6275-202

D91-6281-203 2.813 2.31 ‐D91-6281-202

PX/PXN EQUALIZING PRONG AND VALVE

PX Model Part NumberSize Top OD

in. in.

D91-6187-204 1.875 1.375

D91-6231-204 2.313 1.375

D91-6275-204 2.750 1.375

D91-6281-204 2.813 1.375

109

F WG BY-PA SS B L A N K I N G P LU G

This Plug allows fluid to by-pass through the side ports, when running in the well. Once Plug is locked in a “F” type profile, pressure can be held in either direction. After well has been repaired or tested, Plug can be equalized and pulled with standard wireline tools.

To Run: C-1 Running Tool

To Pull: SB or JDC Pulling Tool, with B Probe

SPECIFICATIONS


in. in. in. psi.

D91-6178-400

2.375

1.781 1.802

10,000

D91-6181-400 1.812 1.865

D91-6187-400 1.875 1.905

D91-6225-4002.875

2.250 2.302

D91-6231-400 2.313 2.365

D91-6275-4003.500

2.750 2.802

D91-6281-400 2.813 2.865

110

FLOW CONTROL TOOLS

R ZG BY-PA SS B L A N K I N G P LU G

This Plug allows fluid to by-pass through the side ports, when running in the well. Once Plug is locked in a “R” type profile, pressure can be held in either direction. After well has been repaired or tested, Plug can be equalized and pulled with standard wireline tools.



SPECIFICATIONS


in. in. in. psi.

D91-6178-401

2.375

1.781 1.776

10,000

D91-6181-401 1.812 1.807

D91-6187-401 1.875 1.870

D91-6225-4012.875

2.250 2.245

D91-6231-401 2.313 2.307

D91-6275-4013.500

2.750 2.745

D91-6281-401 2.813 2.802

111

F W B D OW N I N ST R U M E N T H A N G E R

This Instrument Hanger is used to land and lock geophysical instruments in “F” type profiles to allow recording of reservoir data.

Features/Benefits:

n It allows the well’s Safety System to remain in full operation during the survey.

n It allows removal of wireline from a corrosive environment to prevent damage of wireline.

n Several wells may be surveyed with one wireline

To Run: “C-1” Running Tool


SPECIFICATIONS

Part Number Tubing SizeSize NoGo OD

Bottom Threadin. in.

D91-6178-402

2-3/8”

1.78 1.802

3/4”-16UNF

D91-6181-402 1.81 1.865

D91-6187-402 1.87 1.905

D91-6225-4022-7/8”

2.25 2.302

D91-6231-402 2.31 2.365

D91-6275-4023-1/2”

2.75 2.802

D91-6281-402 2.81 2.865

112

FLOW CONTROL TOOLS

R Z B D OW N I N ST R U M E N T H A N G E R

This Instrument Hanger is used to land and lock geophysical instruments in “R” type profiles to allow recording of reservoir data, unit.

Features/Benefits:

n It allows the well’s Safety System to remain in full operation during the survey.

n It allows removal of wireline from a corrosive environment to prevent damage of wireline.

n Several wells may be surveyed with one wireline

To Run: “C-1” Running Tool


SPECIFICATIONS

Part Number Tubing SizeSize NoGo OD

Bottom Threadin. in.

D91-6178-403

2-3/8”

1.78 1.771

3/4”-16UNF

D91-6181-403 1.81 1.802

D91-6187-403 1.87 1.865

D91-6225-4032-7/8”

2.25 2.240

D91-6231-403 2.31 2.302

D91-6275-4033-1/2”

2.75 2.740

D91-6281-403 2.81 2.802

113

F B-2 EQ UA L I Z I N G C H EC K VA LV E

Equalizing Check Valves are sometimes called “Standing Valves” because they prevent fluid flow in one direction (downward) while allowing full fluid flow in the opposite direction (upward). The “FB-2” seats on the top NoGo shoulder of a “F” type profile which prevents downward movement. It is not locked into the profile, and has a built-in method of allowing equalizing before pulling.


To Pull: SB Pulling Tool

SPECIFICATIONS

Part NumberTubing Size Seal OD OD Pressure

in. in. in. psi.

D91-7178-100

2.375

1.781 1.802

5000

D91-7181-100 1.812 1.865

D91-7187-100 1.875 1.905

D91-7225-1002.875

2.250 2.302

D91-7231-100 2.312 2.365

D91-7275-1003.500

2.750 2.802

D91-7281-100 2.813 2.865

114

FLOW CONTROL TOOLS

R B-2 EQ UA L I Z I N G C H EC K VA LV E

Equalizing Check Valves are sometimes called “Standing Valves” because they prevent fluid flow in one direction (downward) while allowing full fluid flow in the opposite direction (upward). The ‘RB-2” seats on the bottom NoGo shoulder of a “R” type profile which prevents downward movement. It is not locked into the profile, and has a built-in method of allowing equalizing before pulling.


To Pull: SB Pulling Tool

SPECIFICATIONS

Part NumberTubing Size Seal OD OD Pressure

in. in. in. psi.

D91-7178-101

2.375

1.781 1.771

5000

D91-7181-101 1.812 1.802

D91-7187-101 1.875 1.865

D91-7225-1012.875

2.250 2.240

D91-7231-101 2.312 2.302

D91-7275-1013.500

2.750 2.740

D91-7281-101 2.813 2.802

115

B S H I FT I N G TO O L

The “B” Shifting Tool is designed to selectively locate and shift most sliding side door sleeves. This is accomplished by the “B” Shifting Tool keys engaging the SSD inner sleeve, and depending on the direction the tool is run, up or down, the sleeve is shifted.

SPECIFICATIONS

Part NumberSize Top OD

Ends Thread

Key

Contract Spread

in. in. in. in.

D91-4125-200 1.250 1.000 5/8”-11UN 1.210 1.453

D91-4150-200 1.500

1.188

15/16”-10UN

1.406 1.719

D91-4162-200 1.625 1.593 1.890

D91-4171-200 1.710 1.688 2.094

D91-4178-200 1.781

1.375

1.750 1.120

D91-4187-200 1.875 1.840 2.156

D91-4212-200 2.125 1.965 2.438

D91-4231-200 2.3131.750

2.156 2.656

D91-4256-200 2.562 2.530 2.968

D91-4275-200 2.7502.313 1 1/16”-10UN

2.718 3.031

D91-4281-200 2.813 2.720 3.160

116

FLOW CONTROL TOOLS

X-L I N E R U N N I N G TO O L

The X-Line Running Tools are used to run, locate, and set Type X, XN Locks and subsurface safety equipment.

SPECIFICATIONS


Top Thread Bottom ThreadLocks’ID Length

in. in. in in.

D91-2150-200 1.5001.188

15/16”-10

3/8”-16 1.062 30.063D91-2162-200 1.625

D91-2187-200 1.875 1.375 1 /2”-13 1.375 29.313

D91-2231-200 2.313 1.750 5/8”-11 1.812 30.250

D91-2275-200 2.750

2.313 1 1/16”-10 3/4”-10 2.313 31.000D91-2281-200 2.813

D91-2287-200 2.875

117

C-1 R U N N I N G TO O L

The C-1 Running Tool is capable of running and landing several types of FWG, RZG, FSG, FB-2, RB-2 Style Locks and Plugs.

SPECIFICATIONS


Top ThreadLength

in. in. in.

D91-2150-400 1 1/21.188

15/16”-10

5.875D91-2175-400 1 3/4

D91-2200-400 2 1.375 6.250

D91-2250-400 2 1/2 1.750 5.875

D91-2300-400 3 2.313 1 1/16-10 5.750

118

FLOW CONTROL TOOLS

S B SE R I ES P U L L I N G TO O L

The “SB” Series Pulling Tool is a shear down releasing tool used in pulling subsurface devices which have external fishing necks. To accommodate the many different types of devices, the core on the “SB” Series Pulling Tool is made in various lengths and can be changed in the field.

SPECIFICATIONS


Top Thread Bottom ThreadMax OD Length

in. in. in. in.

D91-3125-200 1 1/4 1.000 5 /8”-113 /8”-16

1.219 13.750

D91-3150-200 1 1/2 1.188

15/16”-10

1.418 12.469

D91-3200-200 21.375 1 /2”-13

1.765 14.938

D91-3250-200 2 1/2 2.175 15.328

D91-3300-200 3 2.313 1 1/16”-10 5 /8”-11 2.74 15.313

119

J D SE R I ES P U L L I N G TO O L

The “JD” Series Pulling Tool, through minor component changes, is a shear down or shear up releasing tool used in pulling subsurface devices which have external fishing necks. To accommodate the many different types of devices, the core of the “JD” Series tools is made in various lengths and can be changed in the field.

SPECIFICATIONS


Top Thread Bottom ThreadMax OD Fish Depth

in. in. in. in.

D91-3125-400 1 1/4

1.188

15/16”-10

1 /4”-201.290 1.937

D91-3137-400 1 3/8 1.375 1.875

D91-3150-400 1 1/2

1 /2”-13

1.4221.093

D91-3162-400 1 5/8 1.625

D91-3200-400 21.375

1.859 1.437

D91-3250-400 2 1/2 2.250 1.312

D91-3300-400 3 2.313 2.796 1.437

120

FLOW CONTROL TOOLS

G S R U N N I N G/P U L L I N G TO O L

The “GS” Running/Pulling Tool is a shear down releasing tool used to run or pull subsurface devices which have internal fishing necks.

SPECIFICATIONS


Top Thread Bottom ThreadMax OD Length

in. in. in. in.

D91-3150-300 1 1/2 1.188

15/16”-101 /2”-13

1.469 10.75

D91-3200-300 2 1.375 1.750 11.625

D91-3250-300 2 1/2 1.7505 /8”-11

2.160 11.875

D91-3300-300 3 2.313 1 1/16-10 2.719 12.125

121

G R A DA PT E R

SPECIFICATIONS


Ends threadMax OD Length

in. in. in. in.

D91-3150-301 1 1/2 1.188

15/16”-10

1.4608.375

D91-3200-301 2 1.375 1.813

D91-3250-301 2 1/2 1.750 2.125 8.875

D91-3300-301 3 2.313 1 1/16-10 2.725 9.313

The “GR” Adapter is used in conjunction with the “GS” Pulling Tool to convert it into a “jar up to released” type tool.

122

FLOW CONTROL TOOLS

B P R O B E

The B Probe is a wireline manipulated device that in used to close the dogs (or locks) on a Baker top or bottom NoGo Style lock mandrel in order to remove it from the well.

SPECIFICATIONS


Top Thread Bottom Threadin. in.

D91-3166-602 1 .660” 0.688 3/8”-16UN 1/4”-20UN

D91-3190-602 1.900” 0.938 1/2”-13UN 7/16”-14UN

D91-3237-602 2 3/8” 1.063 1/2”-13UN 1/2”-13UN

D91-3287-602 2 7/8” 1.500 1/2”-13UN 1/2”-13UN

D91-3350-602 3 1/2” 2.000 5/8”-11UN 5/8”-11UN

123

F CO L L A R STO P

The Collar Stop is designed to locate in the collar recess of API upset and non-upset tubing. By lowering the stop to the desired depth and lifting upward, the latch springs are tripped allowing the stop arms to expand into the collar recess. Downward jarring on the inner mandrel pushes it down behind the collar stop arms locking them into places in the collar recess.

SPECIFICATIONS

Part NumberSize Top OD Min ID

Running Tool Retrieve toolin. in. in.

D91-5200-200 2 1.375 0.8752 1/2”F

2”JDC

D91-5250-200 2 1/2 1.750 1.125 2 1/2”JDC

D91-5300-200 3 2.313 1.625 3”F 3”JDC

124

FLOW CONTROL TOOLS

T U B I N G E N D LO C ATO R

The Tubing End Locator is used to determine the depth of the tubing through the use of a spring loaded finger. The spring loaded finger catches the end of the tubing when pulled upward, registering a reading on the surface weight indicator.

SPECIFICATIONS

Part NumberSize Max OD Top OD Length

Threadin. in in. in

D92-6150-200 1 1/4,1 1/2 1.250 1.188 10.625 15/16”-10UN

D92-6200-200 2,2 1/2 1.7501.375

10.438 15/16”-10UN

D92-6300-200 3 2.500 10.438 15/16”-10UN

125

S I N G L E ST R A N D R O P E S O C K E T

The Single Strand Rope Socket is the means used to attach single strand wireline with the wireline tool string. The spool type rope socket is recommended for use with 0.066’’-0.092’’ line.

SPECIFICATIONS

Part NumberSize Top OD Bottom Thread OD Length

in. in. in. in. in.

D92-1075-200 3/4 0.6881/2”-13UN

0.750

5.688D92-1087-200 7/8 0.750 0.875

D92-1100-200 1 1.000 5/8”-11UN 1.000

D92-1125-200 1 1/4 1.18815/16”-10UN

1.2506.188

D92-1150-200 1 1/2 1.375 1.500

D92-1175-200 1 3/4

1.750 1 1/16”-10UN

1.750

7.000D92-1187-200 1 7/8 1.875

D92-1212-200 2 1/8 2.125

126

FLOW CONTROL TOOLS

B R A SS W E D G E R O P E S O C K E T

The Brass Wedge Rope Socket is used as a means of connecting the wireline to the wireline tool string. The line is run through the body and around the brass wedge. With the line set in the provided groove of the brass wedge, the line and brass wedge are pulled tightly into the taper of the body. Recommended for use with 0.092’’-0.187’’ line.

SPECIFICATIONS


in. in. in. in. in.

D92-1125-100 1 1/4 1.18815/16”-10UN

1.250 5.250

D92-1150-100 1 1/2 1.375 1.500 4.813

D92-1175-100 1 3/41.750 1 1/16”-10UN

1.750 5.125

D92-1187-100 1 7/8 1.875 5.125

127

MS R O P E S O C K E T

The Multi-Strand Rope Socket is the means used to attach multi-strand lines with the wireline tool string. The slip type rope socket is designed for use with small stranded lines up through 3/16” diameter.

SPECIFICATIONS


in. in. in. in. in.

D92-1125-300 1 1/4 1.18815/16”-10UN

1.250 8.750

D92-1150-300 1 1/2 1.375 1.500 9.000

D92-1175-300 1 3/41.750 1 1/16”-10UN

1.7509.188

D92-1187-300 1 7/8 1.875

128

FLOW CONTROL TOOLS

W I R E L I N E ST E M

The Wireline Stem, also called a weight bar, is used to add weight to the wireline tool string to counteract the wellbore pressure allowing the easy descent of the tool string. It is also used to increase the effectiveness of jarring operations.

SPECIFICATIONS

Part NumberSize Top OD Ends Thread Length

in. in. in. ft

D92-2075-102

3/4 0.688 1/2”-13UN

2

D92-2075-103 3

D92-2075-105 5

D92-2100-102

1 0.875 5/8”-11UN

2

D92-2100-103 3

D92-2100-105 5

D92-2125-102

1 1/4 1.188

15/16”-10UN

2

D92-2125-103 3

D92-2125-105 5

D92-2150-102

1 1/2 1.375

2

D92-2150-103 3

D92-2150-105 5

D92-2175-102

1 3/4 1.750

1 1/16”-10UN

2

D92-2175-103 3

D92-2175-105 5

D92-2187-102

1 7/8 1.750

2

D92-2187-103 3

D92-2187-105 5

D92-2212-102

2 1/8 1.750

2

D92-2212-103 3

D92-2212-105 5

129

W I R E L I N E R O L L E R ST E M

SPECIFICATIONS

Part NumberSize Top OD Ends Thread Max OD Length

in. in. in. in. ft

D92-2125-202

1 1/4 1.188

15/16”-10UN

1.250

2

D92-2125-203 3

D92-2125-205 5

D92-2150-202

1 1/2 1.375 1.500

2

D92-2150-203 3

D92-2150-205 5

D92-2175-202

1 3/4

1.750 1 1/16”-10UN

1.750

2

D92-2175-203 3

D92-2175-205 5

D92-2187-202

1 7/8 1.875

2

D92-2187-203 3

D92-2187-205 5

The Wireline Roller Stem is a tool used in the wireline work string to minimize the effect of friction caused by the tool string sliding on the tubing wall during wireline work in deviated wellbores.

Roller Stems consist of standard sinker bars with slots to accommodate simple rollers held in position with captive dowel pins.

130

FLOW CONTROL TOOLS

K N U C K L E J O I N T

The Knuckle Joint is designed for applications where tool string rotation and/or deflection is required. It is most useful in fishing operations where the pulling tool or overshot requires flexibility to properly locate the fish.

SPECIFICATIONS


Ends ThreadMax OD

in. in. in.

D92-3075-400 3/40.688 1/2”-13 UN

0.750

D92-3087-400 7/8 0.875

D92-3100-400 1 1.000 5/8”-11 UN 1.000

D92-3125-400 1 1/4 1.18815/16”-10UN

1.250

D92-3150-400 1 1/2 1.375 1.500

D92-3175-400 1 3/41.750 1 1/16”-10UN

1.750

D92-3187-400 1 7/8 1.875

D92-3250-400 2 1/2 2.313 1 9/16”-10UN 2.500

131

K N U C K L E J A R

The Knuckle Jar provides a range of motion that helps to make the tool string more flexible. Because the Knuckle Jar has a stroke, it can also be used for light jarring.

SPECIFICATIONS


Ends ThreadMax OD Stroke Length

in. in. in. ft

D92-3125-5021 1/4 1.188 15/16”-10 UN 1.250

2

D92-3125-503 3

D92-3150-5021 1/2 1.375 15/16”-10 UN 1.500

2

D92-3150-503 3

D92-3187-5021 7/8 1.750 1 1/16”-10 UN 1.875

2

D92-3187-503 3

132

FLOW CONTROL TOOLS

T U B U L A R J A R

SPECIFICATIONS

Part NumberSize Top OD Max OD Stroke Length

Ends Threadin. in. in. in.

D92-3075-300 3/4 0.688 0.75020 1/2”-13UN

D92-3087-300 7/8 0.750 0.875

D92-3100-300 1 0.875 1.000

30

5/8”-11UN

D92-3125-300 1 1/4 1.188 1.25015/16”-10UN

D92-3150-300 1 1/2 1.375 1.500

D92-3175-300 1 3/4

1.750

1.750

1 1/16”-10UND92-3187-300 1 7/8 1.875

D92-3212-300 2 1/8 2.125

The Tubular Jar, through wireline manipulation, can be used to provide an upward or downward impact. The intensity of the jarring impact depends on the weight of the wireline stem above the jar, the stroke length of the jar, and the density of the well fluid. The perforated body of the Tubular Jar allows fluid bypass, reducing the effects of the well fluid density on the jarring impact.

133

L I N K/SPA N G J A R

Wireline Link Jars, sometimes called ‘Spang Jars’ or ‘Mechanical Jars’ are of the cable tool type and utilise the weight of the stems connected immediately above to deliver effective jarring impacts, by manipulating the wireline upwards or downwards at the surface. The effectiveness of these impacts is largely dependant on the weight of the stem used, the length of the stroke of the ‘jars’, the size and straightness of the tubing, the viscosity of the fluid in the tube and the well pressure acting upon the cross sectional area of wireline. ‘Jars’ are composed of two pieces linked together rather like long chain links which are free to be extended or collapsed (stroke).

SPECIFICATIONS

Part NumberTool OD Top OD Ends Thread Stroke Length

in. in. in. in.

D92-3125-2001.250 1.187

15/16 -10UN

20

D92-3125-203 30

D92-3150-2001.500 1.375

20

D92-3150-203 30

D92-3175-2001.75 1.75

1 1/16-10UN

20

D92-3175-203 30

D92-3212-2002.125

2.313

20

D92-3212-203 30

D92-3250-2002.500 1 9/16-10UN

20

D92-3250-203 30

134

FLOW CONTROL TOOLS

W I R E L I N E I N T E N S I F I E R

The Wireline Intensifier is a wireline stretch simulator device used in conjunction with hydraulic or spring jars when jarring at shallow depths in the well bore. The wireline intensifier is available in sizes from 1-1/4” to 3” OD.

Upward tension on the wireline compresses the spring within the intensifier assembly and the stored energy is transferred to the hydraulic or spring jars located further down the tool string.

A combination of surface wireline tension and the energy stored within the spring of the accelerator will eventually cause the hydraulic or spring jar to fire, thus releasing totally the energy stored within the spring. The tension of the wireline can then be relaxed and the operation repeated until the subsurface tool is jarred free.

SPECIFICATIONS

Part NumberTool OD Top OD Top Thread

in. in. in.

D92-4125-100 1.250 1.187

15/16-10UND92-4150-100 1.5001.375

D92-4175-100 1.750

D92-4187-100 1.875 1.7501 1/16-10UN

D92-4250-100 2.5002.313

D92-4300-100 3.000 1 9/16-10UN

135

W I R E L I N E S H O C K A B S O R B E R

The Wireline Shock Absorber is used to dampen the shock transmitted to delicate downhole instruments being run into the wellbore during wireline operations.

The Wireline Shock Absorber basically consists of a fishneck, main body, upper spring, mandrel, lower spring and bottom sub. The lower spring is usually the heavier of the two springs in that it is constantly compressed by the weight of the instruments normally suspended immediately below the shock absorber. The mandrel floats between the upper and lower springs and absorbs shock, therefore protecting the delicate downhole instruments.

SPECIFICATIONS

Part NumberTool OD Top OD Top Thread Bottom Thread

in. in. in. in.

D92-4125-200 1.250 1.187

15/16-10UN

3/4 UN

D92-4150-200 1.5001.375

3/4 UN

D92-4175-200 1.750 3/4 UN

D92-4187-200 1.8751.750 1 1/16-10UN

3/4 UN

D92-4200-200 2.000 3/4 UN

D92-4250-200 2.500 2.313 1 9/16-10UN 3/4 UN

136

FLOW CONTROL TOOLS

PA R A F F I N CU TT E R (G AU G E R I N G)

The Paraffin Cutter (Gauge Ring) has many different purposes. It can be used to calibrate tubing, locate landing nipples, and remove paraffin and other deposits from the tubing wall.

SPECIFICATIONS

Part NumberSize Top OD Top Thread Max OD Length

in. in. in. in. in.

D92-5125-100 1 1/4 1.000 5/8”-11UN 1.240 6.500

D92-5150-100 1 1/21.188

15/16”-10UN

1.483 6.500

D92-5175-100 1 3/4 1.750 8.000

D92-5200-100 21.375

1.906 8.500

D92-5250-100 2 1/2 2.343 8.500

D92-5300-100 3 1.750 1 1/16”-10UN 2.906 8.500

137

W I R E L I N E B L I N D B O X

The Blind Box is used to beat down an obstruction encountered in the tubing string. It is also widely used to cut wireline on a rope socket during fishing operations. The Blind Box is approximately nine inches long with a male thread connection and fishneck facing upwards and flat bottom down. The diameter of the Blind Box should normally be matched to the tubing in which it is to be used.

SPECIFICATIONS

Part NumberSize Top OD Max OD Bottom Thread

in. in. in. in.

D92-5075-200 3 /4 0.688 0.750 1/2”-13

D92-5100-200 1 0.875 1.000 5/8”-11

D92-5125-200 1 1/4 1.188 1.250

15/16-10D92-5150-200 1 1/2 1.500

D92-5200-200 2 1.375 1.750

D92-5250-200 2 1/2 2.250

D92-5300-200 3 1.750 2.625 1 1/16”-10

138

FLOW CONTROL TOOLS

P I N E A P P L E B R OAC H

The Pineapple Broach is used to cut burrs in the tubing I.D. caused by perforation, rust, bent tubing, etc.

SPECIFICATIONS

Part NumberSize Top OD Max OD

Top ThreadLength

in. in. in. in.

D92-5200-300 2 1.375 1.91015/16”-10UN

11.500

D92-5250-300 2 1/2 1.375 2.347 11.500

D92-5300-300 3 1.750 2.897 1 1/16”-10UN 15.000

139

T U B I N G SW E D G E

The Tubing Swedge is used to bend out irregular places and other obstructions within the tubing string. It is equipped with a central bore and angled fluid ports for ample fluid bypass.

SPECIFICATIONS

Part NumberSize Top OD Max OD Length

Top Threadin. in. in in

D92-5125-400 1 1/4 1.000 1.230 6.250 5/8”-11UN

D92-5150-400 1 1/2 1.188 1.531 7.000

15/16”-10UND92-5200-400 2

1.375”1.906 8.000

D92-5250-400 2 1/2 2.3439.250

D92-5300-400 3 1.750” 2.906

140

FLOW CONTROL TOOLS

W I R E L I N E F LU T E D CE N T R A L I Z E R

The Fluted Centralizer is a wireline tool designed to ensure that the work string running or pulling tool is at its most central position, especially during operations in deviated wells.

Normally attached to the tool string just above the running/pulling, or fishing tool, the OD is machined to suit the ID of the tubing in which it is to be run. This allows the tool to be used as a tubing drift or gauge in addition to centralizing the tool string.

SPECIFICATIONS


Ends Threadin. in. in.

D92-6200-000 21.375

1.84315/16”-10UN

D92-6250-000 2 1/2 2.281

D92-6300-000 3 1.750 2.718 1 1/16”-10UN

141

B OW SP R I N G CE N T R A L I Z E R

The Bow Spring Centralizer is designed for use with slickline tool strings or when running downhole gauges out through the tail pipe and into the casing.

The Bow Spring Centralizer is able to pass through the restricted bores of the tail pipe and expand into the casing liner below thus enabling the tools to be held away from the casing.

SPECIFICATIONS

Part NumberSize Top OD Max OD Expand Range

Ends Threadin. in. in. in.

D92-6150-100 1 1/21.375

1.500 1 1/2-8 1/215/16”-10UN

D92-6187-100 1 7/8 1.875 1 7/8-9

142

FLOW CONTROL TOOLS

T WO P I ECE SA N D BA I L E R

The Sand Bailer is a pump action type bailer designed to remove sand and small debris in the tubing string, through the upward stroking motion of the pump section. Sand and debris are held in the load barrel through the use of different style check bottoms. A large percentage of wireline service involves sand bailing prior to the actual pulling or setting of subsurface flow controls.

SPECIFICATIONS

Part NumberSize Top OD Max OD Length Top Thread

in. in. in. in. in.

D92-6100-300 1 1.000 0.750 144.875 5/8”-11

D92-6125-300 1 1/4

1.188

1.000 146.688

15/16-10

D92-6138-300 1 3/8 1.250146.438

D92-6150-300 1 1/2 1.500

D92-6175-300 1 3/41.375

1.750 147.500

D92-6200-300 2 2.250 112.500

143

D U M P BA I L E R

The Dump Bailer is designed to allow a variety of fluids to be dumped within the well on top of any sub-surface device. Wireline Dump Bailers are available in a variety of sizes. The bottom shoe of the Wireline Dump Bailer should always be matched with the downhole device upon which fluid is to be dumped. Bottom assemblies are available with glass shear disc or O-Ring seal piston.

SPECIFICATIONS

Part NumberSize Top OD Length Top Thread

in. in. ft in.

D92-6150-400 1 1/2

1.375

5

15/16-10D92-6175-400 1 3/4

D92-6225-400 2 1/4

1 1/16-10D92-6250-400 2 1/2

2.313D92-6300-400 3

D92-6400-400 4

144

FLOW CONTROL TOOLS

G O D E V I L

The Go Devil is dropped to cut the wireline at the rope socket when the tool string becomes stuck.

SPECIFICATIONS

Part NumberSize Top OD Max OD Length

Bottom Typein. in in. ft.

D93-1125-100

1 1/4 1.188 1.250

5

Deer Foot

D93-1125-101 Flat bottom

D93-1125-102 Mule Shoe

D93-1150-100

1 1/2 1.375 1.500

Deer Foot



D93-1175-100

1 3/4

1.750

1.750

Deer Foot



D93-1187-100

1 7/8 1.875

Deer Foot



145

W I R E F I N D E R SP L I T S K I RT

WITH MADREL TYPE


Ends ThreadLength

in. in. in. in.

D93-3150-100 1 1/2 1.375 1.687 15/16”-10UN14.125

D93-3200-100 2 1.750 1.812 1 1/16”-10UN

STANDARD TYPE


Top ThreadLength

in. in. in. in.

D93-3200-101 2

1.375

1.813

15/16”-10UN

10.938

D93-3250-101 2 1/2 2.400 11.313

D93-3300-101 3 2.740 10.938

The Wirefinder Split Skirt is used to bend or ball the uppermost part of the wire so that retrieving applications may be used.

146

FLOW CONTROL TOOLS

CE N T E R SP E A R

The Center Spear is made by welding barbs on a pointed rod. It is most commonly used when the wire is balled up and stuck in the tubing. It can be driven into the tangled wire to loosen it and facilitate the use of a two prong wire grab for final wire retrieval.

SPECIFICATIONS


Top ThreadLength

in. in. in.

D93-3200-200 21.188

15/16”-10UN 22.000

D93-3250-200 2 1/2 15/16”-10UN 22.000

147

T WO P R O N G W I R E L I N E G R A B

The Two Prong Wireline Grab is used to retrieve broken wire from the tubing string. The arms include welded bards which catch the wire.

SPECIFICATIONS

Part NumberSize Top OD Mad OD

Top ThreadLength

in. in. in. in.

D93-3125-202 1 1/4 1.000 1.230 5/8”-11UN 23.875

D93-3150-202 1 1/2 1.188 1.490 15/16”-10UN 23.938

D93-3175-202 1 3/4

1.375

1.740 15/16”-10UN 23.938

D93-3200-202 2 1.750 15/16”-10UN 23.938

D93-3250-202 2 1/2 2.250 15/16”-10UN 25.250

D93-3300-202 3 1.750 2.625 1 1/16”-10UN 24.500

148

FLOW CONTROL TOOLS

“BA I T I N G” TY P E B U L L D O G SP E A R

The “Baiting” Type Bulldog Spear is used to retrieve (fish) wireline tools lost in the well bore that do not have a conventional fishing neck and are therefore best fished with an internal spear.

The spear is run on a ‘GS’ running/pulling tool and speared into the fish. In the event the fish cannot be pulled the ‘GS’ running/pulling tool will shear its pin and release. This will leave an internal fishing neck ’looking up’, to enable further fishing attempts. The fish is then said to be baited.

The ‘Baiting’ Type Bulldog Spear has an optional Engagement Stop Ring (shown) available on request.

SPECIFICATIONS

Part NumberSize Max OD Fishing Neck

Fishing Rangein. in. in

D93-2200-100

2” 1.85” 1.375”

0.875”-1”

D93-2200-101 1”-1.125”

D93-2200-102 1.125”-1.25”

D93-2200-103 1.25”-1.375”

D93-2200-104 1.375”-1.5

D93-2250-100

2-1/2” 2.28” 1.812”

1.125”-1.25”

D93-2250-101 1.25”-1.375”

D93-2250-102 1.5”-1.675”

D93-2250-103 1.675”-1.75”

D93-2250-104 1.75”-1.875”

D93-2250-105 1.875”-2”

D93-2300-100

3” 2.72” 2.313”

1.75”-1.875”

D93-2300-101 1.875”-2”

D93-2300-102 2”-2.25”

D93-2300-103 2.25”-2.5”

D93-2350-100

3-1/2” 3.625” 2.625”

2.5”-2.75”

D93-2350-101 2.75”-3”

D93-2350-102 3”-3.25”

D93-2350-103 3.25”-3.5”

149

R E L E A SA B L E OV E R S H OT

The Releasable Overshot is a slip type overshot used to retrieve a fish lost in the well bore that does not have a conventional fishing neck.

Once latched onto a fish the overshot can be released by jarring downwards provided the overshot has a solid footing upon which the core can be driven against.

SPECIFICATIONS

Part NumberOD Fishing Neck

Top ThreadSlip Range

in. in. in.

D93-2185-200 1.850”1.375” 15/16UN

0.5~1.50

D93-2225-200 2.250” 0.5~1.75

D93-2262-200 2.625” 1.75”

1-1/16UN

0.5~2.00

D93-2325-200 3.250”2.313

0.5~2.31

D93-2380-200 3.800” 0.5~2.75

WIRELINE RELEASABLE OVERSHOT (SLIPS) TABLE

Nominal Size 2” 2 1/2” 3” 3 1/2” 4”

Actual O.D. 1.850” 2.250” 2.625” 3.250” 3.800”

Nominal Slip Size (in)

Catch Range Catch Range Catch Range Catch Range Catch Range

in in in in in

1/2” 7/16-9/16 7/16-9/16 3/8-9/16 3/8-5/8

5/8” 9/16-11/16 9/16-11/16 9/16-3/4 1/2-11/16

3/4” 11/16 -13/16 11/16 -13/16 11/16-7/8 5/8-7/8

7/8” 13/16-15/16 13/16-15/16 3/4-15/16

1 15/16-1 1/16 15/16-1 1/16 15/16-1 1/8 7/8-1 1/16 7/8- 1 1/8

1 1/8” 1 1/16-1 3/16 1 1/16-1 3/16 1 1/16-1 1/4

1 1/4” 1 3/16-1 5/16 1 3/16-1 5/16 1 1/8-1 5/16 1 1/8-1 3/8

1 3/8” 1 5/16-1 7/16 1 5/16-1 7/16 1 5/16-1 1/2 1 1/4-1 7/16

1 1/2” 1 7/16-1 9/16 1 7/16-1 9/16 1 7/16-1 5/8 1 3/8-1 5/8

1 5/8” 1 9/1-1 11/16” 1 1/2-1 11/16

1 3/4” 1 5/8-1 3/4 1 11/16-1 7/8 1 5/8-1 13/16 1 5/8-1 7/8

1 7/8” 1 13/16-2

2” 1 7/8-2 1/16 2-2 3/16 1 7/8-2 1/8

2 1/4” 2 1/8-2 5/16 2 1/8-2 3/8

2 1/2” 2 3/8-2 5/8

2 3/4” 2 5/8-2 7/8

150

FLOW CONTROL TOOLS

H E AV Y D U TY M A G N E T F I S H I N G TO O L

The Heavy Duty Magnet Fishing Tool is a wireline service tool used to magnetically attract and retrieve ferrous debris lost in the well bore.

SPECIFICATIONS

Part NumberMax OD Fishing Neck

Top ThreadFishing Weight

in. in. kg

D93-5125-200 1.251.188

15/16-10UN

4D93-5150-200 1.5

D93-5175-200 1.75

1.375D93-5200-200 2 15

D93-5225-200 2.25 33

D93-5250-200 2.560

D93-5300-200 31.75

1 1/16-10UND93-5400-200 4

130D93-5500-200 5 2.313

D93-5600-200 6 3.125 1 9/16-10UN

151

I M P R ESS I O N B LO C K

The Impression Block consists of a steel housing with a lead insert. Impression Blocks are used during fishing operations to determine the shape, size and position of the object being fished.

SPECIFICATIONS


Top ThreadLength

in. in. in. in.

D93-5075-200 3/4 0.688 0.750 1/2”-13UN 4.875

D93-5100-200 1 0.875 1.000 5/8”-11UN 5.250

D93-5125-200 1 1/4 1.188 1.250 15/16”-10UN 5.500

D93-5150-200 1 1/2 1.188 1.500 15/16”-10UN 5.500

D93-5200-200 2 1.375 1.750 15/16”-10UN 6.000

D93-5250-200 2 1/2 1.375 2.250 15/16”-10UN 6.000

D93-5300-200 3 1.750 2.625 1 1/16”-10UN 6.000

152

FLOW CONTROL TOOLS

P X P LU G & F WG/R ZG P LU G SE R I ES TO O L S

PX PLUG SERIES TOOLS

Plug Nipple Circulating Sleeve T-2 On-Off Tool

Part Number Size Part Number Part Number Part Number

D916187200 1.87”PX D902187110 D907187201 D905237504

D916231200 2.31”PX D902231110 D907231201 D905287505

D916281200 2.81”PX D902281110 D907281201 D905350507

PX/PXN RUNNING AND PULLING TOOLS

Plug Lock Mandrel Running ToolEqualizing Prong Run-ning/Pulling Tool

Lock Mandrel Pulling Tool

Part Number Size X-line Running Tool SB Pulling Tool JDC Pulling ToolGS Running/Pulling Tool

D916187200/ D916187201 1.87”PX/PXN D912187200

D913200200 D913200400

D913200300

D916231200/ D916231201 2.31”PX/PXN D912231200 D913250300

D916281200/ D916281201 2.81”PX/PXN D912281200 D913300300

Note: For Equalizing Prong Running/Pulling Tool, choose one from SB or JDC is ok.

FWG/RZG PLUG SERIES TOOLS

Plug Nipple

Part Number Size F model R model

D916178400/ D916178401 1.78”FWG/RZG D902150310 D902150410

D916181400/ D916181401 1.81”FWG/RZG D902178310 D902178410

D916187400/ D916187401 1.87”FWG/RZG D902181310 D902181410

D916225400/ D916225401 2.25”FWG/RZG D902187310 D902187410

D916231400/ D916231401 2.31”FWG/RZG D902225310 D902225410

D916275400/ D916275401 2.75”FWG/RZG D902231310 D902231410

D916281400/ D916281401 2.81”FWG/RZG D902275310 D902275410

Note‐FWG running with F profile nipple‐RZG running with R profile nipple

FWG/RZG RUNNING AND PULLING TOOLS

By-Pass Blanking Plug Plug Running Tool Lock Mandrel And Equalizing Prong Pulling ToolLock Mandrel Pulling Tool

Part Number Size C-1 SB JDC B

D916178400/ D916178401 1.78”FWG/RZG

D912200400 D913200200 D913200400 D913237602D916181400/ D916181401 1.81”FWG/RZG

D916187400/ D916187401 1.87”FWG/RZG

D916225400/ D916225401 2.25”FWG/RZGD912250400 D913250200 D913250400 D913287602

D916231400/ D916231401 2.31”FWG/RZG

D916275400/ D916275401 2.75”FWG/RZGD912300400 D913300200 D913300400 D913350602

D916281400/ D916281401 2.81”FWG/RZG

Note: Run in the same tool two times, to pulling the Lock Mandrel And Equalizing Prong.

153

I II III IV

SJS Downhole Solutions

TestingConventional Testing Single Test String

Zonal Testing Multi-Test String

Treating

Single Acid Fracturing Mechanical / Hydraulic Packer

Multi-Acid Fracturing Multi-Acid Fracturing String

Acid Fracturing Horizontal Wells

Mutil-frac String with Composite Bridge Plug

Coil Tubing Jet Fracturing String

Open Hole Packer + Frac Sleeve

Production

Conventional Production Completion String

Landing Nipple, Circulating Sleeve, Packer

Single Production String Mechanical / Hydraulic Packer

High-Pressure Injection String Anchor Packer

WorkoverIsolate The Zone

Permanent Bridge Plug

Retrievable Bridge Plug

Re-Cementing Cement Retainer

Composite Solutions

Perforation, Fracturing, Testing, Combination

Testing Tools, Packer, Perforating Gun

Multi-Fracturing Testing Multi-Fracturing Testing Combination String

I II III IV

SJS Oil Tools

Production Tools

Production PackerPermanent Production Packer

Retrievable Production Packer

Accessories

Stinger

Expansion Joint

Tubing Anchor

Service Tools (1) Retrievable Tools

Mechanical Packer

Hydraulic Packer

Retrievable Bridge Plug

Hydraulic Anchor, Cycle Valve, Safety Valve

Service Tools (2)

Permanent Tools

Casting Iron Bridge Plug, Cement Retainer

Composite Bridge Plug / Big Bore Bridge Plug

Dissolvable Bridge Plug

Accessories

Setting Tools

Stinger / Centralizer

Milling Tools / Dump Bailer

Flow Control Tools

Tubing Mounted Equipment Landing Nipple, Circulating Sleeve

Flow Control Accessories Lock Mandrel, Blanking Plug

Slickline Service Tools Slickline Tools String

Coiled Tubing Tools

Standard Toolstring Components Coiled Tubing Toolstring

Application Tools Wash, Mill, Plug Tools

Coiled Tubing Fishing Tools Spear, Overshot, Grab

Drilling Tools

Drilling Tools Drill Collar, Stabilizer, Jar, Shock Absorber

Cementing Tools Float Collar, Float Shoe, Cementing Head, Liner Hanger

Workover Tools Fishing Tools, Milling Tools

D OW N H O L E O I L TO O L S SE R I ES

154

Downhole Oil Tools

(86)716-8016585 [email protected]

Xihuan Road, JingzhouHubei, China

www.sjs.ServaCorp.com

DOWNHOLE OIL TOOLS - · PDF fileDOWNHOLE OIL TOOLS. ii ... We invite you to contact our downhole tools team to learn how we can bring a world of re- ... Motor

Documents