8/9/2019 Dosage Form I
1/229
8/9/2019 Dosage Form I
2/229
Chapter I
PARENTERAL PRODUCTS
8/9/2019 Dosage Form I
3/229
Sterilization
The complete destruction or elimination of microbial life.
Efficiency of sterilization technique depends on:
- Length and degree of exposure to sterilization
source.
- Type of microorganisms.
- Number of microorganisms.
8/9/2019 Dosage Form I
4/229
Methods of sterilization
1- Dry heat sterilization
Suitable for thermostable substances.
2 hrs at 180C or 45 min at 260 C including lag time.
Lag time depends on:- Oven size
- Heat circulation -
- loading capacity.
Application: Fixed oils-petrolatum-Heat stable powder-
glassware-instruments.
8/9/2019 Dosage Form I
5/229
8/9/2019 Dosage Form I
6/229
2- Moist heat sterilization (autoclave)
Effective 121 C and 15 pounds pressure for 20 min.
Cannot destroy pyrogens. More effective than dry heat due to:
a- Coagulation of cell protein at lower temperature.
b- Steam has a higher thermal capacity than hot air.
Application: Aqueous solutions-surgical dressings-
glassware-instruments.
Not applicable in: oils-fats-powders damaged by steam.
8/9/2019 Dosage Form I
7/229
Bulk solution takes more time for sterilization than
the same volume when subdivided.
Cooling cycle of autoclave can be shortened by:
a- Spraying with gradually cooling water.
b- Pulses of cooling air.
8/9/2019 Dosage Form I
8/229
3- Gas sterilization (for thermolabile)
Ethylene oxide or beta-propiolactone are used.
Ethylene oxide (inflammable) is mixed with inert gas asFreon, or may be used as liquefied gas.
Conditions: 55 C - vacuum 27 inch Hg - 50-60% relativehumidity.
Mechanism: alkylating essential metabolites.
Application: dry powders- plastic materials.
8/9/2019 Dosage Form I
9/229
8/9/2019 Dosage Form I
10/229
4- Sterilization by ionizing radiation (for thermolabile)
Advantages : low chemical reactivity-low measurable residue-fewvariables.
a- Gamma radiation: - decay from cobalt 60.
- Provides continuous process. Conditions: 2.5 M.Rad.Adequate dose delivery complete and
uniform Coverage of product adequate penetration.
Application: Sutures- plastics- dry powder drugs as vitamins,
antibiotics.
b- Electronbeam radiation: produced by electron accelerator.
8/9/2019 Dosage Form I
11/229
8/9/2019 Dosage Form I
12/229
5- Sterilization by filtration (for thermolabile)
It should not change the composition of the solution.
Filters are membrane type and act through sieving. (Millipore).
Filters are hydrophobic plastic polymers (cellulose acetate, PVC).
Membranes are rendered hydrophilic by addition of surfactant
during manufacture. Pore size of the filters is 0.2 micron. (series may be used).
Depth filter (pre-filter) may be used for high particle content.
8/9/2019 Dosage Form I
13/229
Testing of filters (for pore size and integrity)
a- Bubble point test: pressure required to pass gas through
wet filter is measured which is inversely proportional to the
diameter of the pores.
b- Microbial challenge test: filtration of solution of high No.
of small microorganisms , then testing the
fi growth on culture.
8/9/2019 Dosage Form I
14/229
Parenteral Products
Advantages (reasons) of parenterals
1- Delivery of adequate drug conc. to diseased tissue (intra-
ventricular).
2- Guarantee drug compliance (monthly IM long acting penicillin).
3- Direct control of onset time, tissue conc. and elimination.
4- For drugs which cannot be taken orally (Insulin- some
penicillins).
5- When oral route is not available.( comatose anesthetic use)
6- Provide local effect (local anesthetics- ant-inflammatory). 7- Rapid correction of fluid and electrolyte imbalance.
8/9/2019 Dosage Form I
15/229
Disadvantages
1- Pain and discomfort.
2- Incorrect drug or dose is difficult counteract.
3- Restricted to hospital or specialized personnel.
8/9/2019 Dosage Form I
16/229
Routes of parenteral administration
1- Subcutaneous (SC) :
Injection of up to 1 ml into fat layer under skin. (insulin-vaccines )
Slower onset and lower absorption rate than IM and IV.
Site of injection: Abdomen, legs and arms.
http://upload.wikimedia.org/wikipedia/commons/f/fa/Mantoux_tuberculin_skin_test.jpghttp://upload.wikimedia.org/wikipedia/commons/f/fa/Mantoux_tuberculin_skin_test.jpg8/9/2019 Dosage Form I
17/229
2- Intramuscular(IM):
- Injected into deltoid, gluteal or lateral thigh. Up to 5 ml.
-Slower than IV. Solutions, suspensions and emulsions ( o/w and w/o)can be injected.
-Depot of drug is formed in the muscle (onset time is 1-2 hr).
-Drug release from the depot depends on:
Rheology of product-Drug conc.-tonicity of product-physical properties
of drug.
- In adults the upper outer quadrant of the gluteus maximus is the most
frequently used site for IM injections.
- In infants, the gluteal area is small and composed primarily of fat, notmuscle. Thus the deltoid muscle of the upper arm or midlateral muscle of
the thigh is preferred.
8/9/2019 Dosage Form I
18/229
Deltoid Gluteal Lateral thigh
8/9/2019 Dosage Form I
19/229
3- Intravenous :
Advantages:
a- Rapid response and maximum bioavailability.
b- Avoid tissue irritation (cytotoxic drugs).
Disadvantages : very difficult antidoting due to rapid absorption.
The veins suited in front of the elbow are
usually selected for IV injection, because
they are largesuperficial
Easily detectable
8/9/2019 Dosage Form I
20/229
Volume: 1-100 ml. only aqueous or hydroalcoholic.
Large volume parenterals (LVP) are used to:
- Supply electrolytes and nutrients,- To restore blood volume,
- To prevent tissue dehydration and
- To dilute toxic materials.
IV admixture
Addition of drug or more to LVP to provide continuous and
prolongedtherapy.
Physical and chemical incompatibilities or loss of sterility
should be avoided during preparation.
http://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=X8/9/2019 Dosage Form I
21/229
Calculations involving
IV admixture Example1:
A medication order for a patient weighing 70 kg calls for 0.25 mg ofamphotericin B per kg of body weight to be added to 500 ml of 5 %dextrose injection. If the amphotericin B is to be obtained from areconstituted injection that contains 50 mg per 10 ml, how many
milliliters should be added to the dextrose injection?
Solution
Total quantity needed for the patient:
0.25 x 70 = 17.5 mg
Reconstituted solution contain 50 mg per 10 ml50 mg 10 ml
17.5 mg X
X= 3.5 ml
http://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=X8/9/2019 Dosage Form I
22/229
Example 2
Prepare the following intravenous infusion
15 mEq of potassium ions and 20 mEq of sodium ions in 500 ml of 5 %
dextrose injection. Using an injection of potassium chloride containing 6
g per 30 ml and saline solution.
http://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=X8/9/2019 Dosage Form I
23/229
Solution
15 mEq of K+ will be supplied by 15 mEq of KCl
And 20 mEq of Na+ will supplied by 20 mEq of NaCl
1 mEq of KCl = 74.5 mg
15 mEq of Kcl = 1117.5 mg or 1.118 g
6 g 30 ml
1.118 g X
X= 5.59 ml
1 mEq of NaCl = 58.5 mg
20 mEq of NaCl = 1170 mg or 1.17 g
0.9 g 100 ml
1.17 g X
X = 130 ml.
http://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=X8/9/2019 Dosage Form I
24/229
Example 3
A medication order calls for 1000 ml infusion to be administered overan 8-hour period. Using an IV administration set which delivers 10drops per ml, how many drops per minute should be delivered to the
patient?
Solution:
Volume of fluid = 1000 ml
8 hour = 480 minutes
1000/ 480 = 2.1 ml per min
2.1 ml/min x 10 (drops per ml) = 21 drops/minute
http://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=Xhttp://images.google.com/imgres?imgurl=http://www.origen.net/Images/DMSO.All.jpg&imgrefurl=http://www.origen.net/dmso.html&h=436&w=500&sz=48&hl=ar&start=1&um=1&tbnid=aUqZYfHrzTPN8M:&tbnh=113&tbnw=130&prev=/images?q=vials+and+syringes&um=1&hl=ar&rlz=1T4ADBS_en___SA202&sa=X8/9/2019 Dosage Form I
25/229
4- Specialized LVP and sterile solutions
A) Hyperalimentation solution
LVP containing large amounts of nutrients (carbohydrate-amino
acids-vit.)
Administered through superior vena cava by catheter, for patients
unable to feed orally (comatose-esophageal obstruction-GI
disease)
8/9/2019 Dosage Form I
26/229
B) Dialysis solutions
1- Peritoneal dialysis solutions:
Sterile solutions are injected into abdominal cavity for 30-90 min.
, and then withdrawn, for the purpose of:
- removing toxic substances from the body.- to aid and accelerate the normal excretion function of the
kidney.
8/9/2019 Dosage Form I
27/229
2- Hemodialysis :
The blood leaves the artery via a PE catheter and passesthrough a disposable dialyzing membrane unit, which is
bathed in electrolyte solution simulating body fluids. After
cycling the blood through the dialyzer, it enters the body
through a vein.
C) Irrigating solutions
They are intended to irrigate, flush and aid in cleansing
cavities and wounds.
8/9/2019 Dosage Form I
28/229
Design of parenteral products
It depends on:
I- Nature of the drug :
- Its solubility in water .
- Its stability in aqueous solutions.
II- Therapeutic considerations:
Onset and duration of action of the drug which dependson:
- The nature of the drug and
- Route of administration.
8/9/2019 Dosage Form I
29/229
A- The Active Drug
Physico-chemical properties of drug includes:
1- Crystallinity and particle size distribution
Crystallization process variables (such as temperature, rate of
mixing and stirring, pH, solvent conc. and purity) will affect:
- Crystal form
- Crystal size and shape
- Size distribution
- Degree of crystallinity
- State of aggregation.
8/9/2019 Dosage Form I
30/229
8/9/2019 Dosage Form I
31/229
3- Polymorphism
It has direct effect on:
- solubility
- stability
- dissolution rate
- drug absorption.
4- pHProfiles of pH versus stability and solubility are needed to predictthe optimum conditions for formulation, preparation andstorage.
8/9/2019 Dosage Form I
32/229
B- Added Substances
1- Antioxidants
- Drugs with high oxidation potential are less sensitive tooxidation.
- The oxidation potential of drugs could be increased by loweringthe pH of the medium.
- Oxidation reactions mediated by free radical mechanism areprotected by agents having lower oxidation potential(Antioxidants) than the drug.
- Antioxidant should not interact with the drug, Ex. Epinephrinestabilized by bisulphite forms inactive epinephrine sulphonate.
- When oxygen is directly involved (auto-oxidation) protectionmay be afforded by replacing air from the system with inert gas(Nitrogen or CO2).
8/9/2019 Dosage Form I
33/229
Antioxidant conc depends on :
- Drug reactivity.
- Type of container (glass seal or rubber stopper).
- Single or multiple dose use.
- Container head space.
Examples of antioxidants :bisulfites metabisulfites sulfites.
ascorbic acid monothioglycerol.
8/9/2019 Dosage Form I
34/229
2- Antibacterial agents
They are generally required for:
a) All multiple-dose parenerals.b) Unit-dose products which are not terminally sterilized.
They should be compatible with all ingredients in the product.
Their activity may be reduced in presence of macro-molecules due to
binding, Ex. Surfactants. Plastics and rubber closures may also adsorbantibacterials, reducing its activity.
They have dual role in the formulation:
1- They inhibit microbial growth accidentally introduced during
withdrawal of dose in multiple dose preparations
2- They have antimicrobial effect during filling under aseptic
conditions.
They are excluded in LVP. due to toxicity.
8/9/2019 Dosage Form I
35/229
3- Buffers
They are added to resist change of pH that may occur during storage
due to:
1- Product degradation.
2- Container and stopper effect.
3- Diffusion of gases through the closure or container.
4- Effect of gases in the head space.
The buffer system should have adequate buffer capacity to maintain
the pH during storage while permitting the body fluids to adjust the
pH easily to 7.4 Suitable buffer system can be selected from the knowledge of pH
profile of the drug for both solubility and stability.
8/9/2019 Dosage Form I
36/229
Buffer system may affect drug stability,
Ex. Degradation of Vitamin B1 with citrate buffer
Phosphate buffer increases the rate of
hydrolysis of Phenethicillin.
Buffers are weak acids and their salts or weak bases andtheir salts.
Ex. Acetate citrate Phosphate
Acceptable pH range:
For small volume IV : 3 10.5
Other parenteral routes : 4 - 9
8/9/2019 Dosage Form I
37/229
8/9/2019 Dosage Form I
38/229
5- Inert gases:
To improve stability of oxygen-sensitive drugs.
Dissolved oxygen may be removed from water by boiling ,
then air is displaced with N2 or CO2.
glass seal provides the best resistance to gas permeation.
6- Solubilizing agents:
Surfactants are used in parenteral:
Suspensions as wetting agent and to improve syringeability
Emulsions as emulsifying agent.
Solutions as solubilizing agent (in steroids).The most safe surfactant is the non-ionic type.
8/9/2019 Dosage Form I
39/229
7- Tonicity adjustment agents:
LVP given by IV route should be isotonic.
Hypotonic leads to hemolysis of RBCs.
While :
hypertonic leads to crenation of RBCs.
Dextrose sod. Chloride pot. Chloride are commonly used.
8/9/2019 Dosage Form I
40/229
C- Solvent system:
The majority of parenterals are aqueous solutions.
Advantages of solutions:
- Provide uniform doses.- Accurately measured.
- Visually inspected for ppt. or colour change.
But it is not possible to formulate drugs in completely aqueous
system because of :- limited aqueous solubility(due to high polarity of H2O)
- limited stability.
Solubility of drugs in aqueous system can be improved by
addition organic co-solvents as ethanol, propylene glycol,glycerol or PEG 400 by lowering Dielectric constant ofwater(polarity).
8/9/2019 Dosage Form I
41/229
Selection of the vehicle depends on:a) Polarity of cosolvent:
Cosolvents with high dielectric constants e.g. ethanol and glycerin mix well with
water and dissolve ionic compounds, while those with low dielectric constants
e.g. chloroform, benzene and oils are not water miscible and dssolve non-ionic compounds.
The solubility profile of the drug as afunction of dielectric constantshould be
done in binary solvent system, from which the dielectric constant of
maximum solubility could be determined.
Drug
Solubility
10 20 30 40 50 60 70 80 90 100
Dielectric constant
% of water
Solubility profile of a drug versus dielectric constant in binary system of
water and dioxane
57 : 43 water : dioxane
8/9/2019 Dosage Form I
42/229
8/9/2019 Dosage Form I
43/229
b) Effect of molecular structure
- Crystals composed of asymmetric molecules tend to be more
soluble than those of highly symmetric molecules.
- Drugs with polymorphic transformation e.g. Chloramphenicol,
Progesterone and Sulphathiazole have different arrangement of
molecules in the crystalline state resulting in different dissolution rates
and different bioavailability.
8/9/2019 Dosage Form I
44/229
The selected pH of the aqueous system depends on thenature of the drug.
Most drugs are weak electrolytes, therefore they arepartially dissociated.
The ratio of dissociated to un-dissociated drug depends onthe pH. Therefore, solubility, stability and partitioncoefficient will be influenced by the pH.
Weak acid drugs as barbiturates and sulfonamides are moresoluble at high pH, While
weak base drugs as antihistamines and akaloids are moresoluble at low pH.
1 A hi l
8/9/2019 Dosage Form I
45/229
1- Aqueous vehicles:
Water for injection (WFI):
- It is non-sterile, pyrogen free. Stored in large tanks.
- Inorganic compounds are removed by distillation, reverse osmosis,deionization.
- Purity specifications limit Cl-, Ca++, SO4, NH3, CO2 and dissolvedsolids (10 ppm).
- Membrane and depth filters are used to remove particulate
contaminants and microorganisms.- Charcoal beds may be used to remove organic materials.
It is used in preparation of parenterals.
Sterile water for injection USP:
Sterile, pyrogen free and packaged as 1 litre container.Used as a solvent or diluent for sterile preparations.
It cannot be administered as LVP as it is not isotonic.
8/9/2019 Dosage Form I
46/229
Bacterostatic water for injection USP:
Sterile WFI containing antimicrobial agent.
Packed in vials not more than 30 ml, used in preparation of
sterile small volume parenterals, especially multiple-dosepackages.
Not used for preparation of LVP due to probable toxicity of
antimicrobial in large doses.
Sodium chloride injection USP (Saline)
Sterile isotonic solution of sod.chloride (0.9%) in WFI.
Used in LVP and in preparation of parenteral solutions or
suspensions.
Bacterstatic sodium chloride injection USP
8/9/2019 Dosage Form I
47/229
2- Non-aqueous (Oils) and mixed vehicles
They are necessary to:
a) Stabilize drugs e.g. barbiturates (hydrolyze by H2O).
b) Improve solubility e.g. Digoxin.
Ex. Of non-aqueous vehicles: Fixed oils as corn oil,
cottonseed oil, peanut oil and sesame oil.
Fixed oils are injected only by IM route.
Used to prepare steroid hormones. Benzyl benzoate is added
to improve steroid solubility in the oil.
Mixed solvents are used to improve drug solubility and
stability.
Mixed solvent systems may be irritating or toxic when
present in high percentage.
8/9/2019 Dosage Form I
48/229
D- The container and container components:
Container components are considered as integral part of the
product, affecting its stability and safety.
Selection of container material is based on:
- Maintenance of microbiological purity.
- Product stability.
- Suitability to production operation and inspection.
- Resistance to breakage and leakage.
- Convenience of clinical use.
GlassAdv. : Economic inert good product identification.
Disadv. : Fragile heavy no satisfactory closures.
8/9/2019 Dosage Form I
49/229
Pl ti
8/9/2019 Dosage Form I
50/229
Plastics:
They are compounds of high M.Wt. that can be molded to shape.
Plastic material may contain additives such as:
Plasticizer Stabilizer Antioxidant- Antistatic Plastics commonly used in parenterals include:
Polyethylene: used in manufacture of syringes.
Polypropylene: autoclavable - manufacture of syringes.
Polyvinyl chloride (PVC): in manufacture of IV bags.
Nylon: hard- manufacture of filters in blood sets.
Factors involved in selecting plastic material:
Vapor transmission sterilization quality texture clarity
inertness leaching biologic safety.
Ad f l i b l i
8/9/2019 Dosage Form I
51/229
Advantages of plastic bags over glass containers:
1- No venting is required due to responding to normal outside
pressure, so contamination is eliminated.
2- Non-breakable, lighter and consume less space.
3- They have less particulate matter than glass.
Advantages of glass containers over plastic bags:
1- Complete mixing occurs more likely in glass containers.
2- Addition of drugs by puncture of plastic bag with needle may
cause contamination.
3- Drug may be adsorbed by plastic materials, affecting its
concentration in the product.
R bb l
8/9/2019 Dosage Form I
52/229
Rubber closures:
The main polymers used in manufacture of rubber are
saturated and unsaturated elastomers. Additives may be
included to improve rubber quality such as:Plasticizers- fillers- accelerators- activators..
To maintain batch to batch uniformity, the following control
tests are necessary.
A- Physical properties
1- Durometer: is a measure for rubber hardness. Values of 30-
35 is soft, 35-45 is medium and above 45 is hard. High
durometer means increased coring, reduced resealability
and increased resistance to puncture. High durometer isneeded in syringe plunger head.
2 C i i th t t f ll ti l f th t
8/9/2019 Dosage Form I
53/229
2- Coring: is the cut out of a small particle from the stopper as
the needle is inserted. It is influenced by rubber type and
thickness.
3- Resealability: Stopper must reseal after needle insertion toprevent contamination and leakage.
4- Puncture resistance: The pressure required to insert the
needle through the closure.
5- Compression test: The closure material should have goodrecovery after compression to assure good sealing with the
glass finish.
6- Moisture vapor transmission (MVT) : is important for
hygroscopic, lyophilized and products with over-head inertgas. MVT can be decreased by increasing filler content.
7- Tackiness: The sticking of closures on autoclaving.
B) C tibilit ith ti
8/9/2019 Dosage Form I
54/229
B) Compatibility with preparation:
Two main problems are involved:
1- Leaching of ingredients from the stopper (as waxes) and
reaction with the ingredients of the preparation (detected
by examination of turbidity of the product)
2- The adsorption of ingredients from the preparation (as
preservatives) by the closure (detected by evaluation of the
extracts of the closures).
Parenteral Production
8/9/2019 Dosage Form I
55/229
Parenteral Production
A) Facilities:
The plant floor should be designed in a series of zones to
provide barriers for contamination.
Walls, ceilings and floors should be constructed of hard,smooth, non-flaking and easily cleanedmaterials.
All lights and windows are flush mounted in walls andceilings for ease of cleaning and disinfection.
Separate entrance for personnel and equipment should beprovided through air locks which are kept at positive
pressure relative to less clean areas.
8/9/2019 Dosage Form I
56/229
Fresh outside air must be first filtered to remove particulate
8/9/2019 Dosage Form I
57/229
Fresh outside air must be first filtered to remove particulate
matter, then HEPA (High Efficiency Particulate Air) filters are
used to remove microorganisms and submicron particles
(purity up to 99.7%). The requirements proposed by GMP include:
- Particle count per cubic foot of air must not exceed
100000 in size range 0.5 um (class 100000) and
class 100 at filling and sealing area.
- A temperature of 22 3 C.
- A relative humidity range of 30 50 %
- At least 20 air exchange per hour.
A laminar air flow units provide environmental control for
aseptic area.
8/9/2019 Dosage Form I
58/229
8/9/2019 Dosage Form I
59/229
For sterile pharmaceutical preparations, clean room can beclassified to four grades as follows:
Grade A:
Local zone for high risk operations, e.g. filling, asepticconnections.
Grade B: Background environment to grade A (in case of aseptic
preparation).
Grade C and Grade D:
Clean areas for less critical operations.
Normally such conditions are provided by a laminar-airflowworkstation.
8/9/2019 Dosage Form I
60/229
Grade At rest In operation
maximum p ermitted number of part icles/m3
0.5 - 5.0 m > 5 m 0.5 - 5.0 m > 5
A 3 500 0 3 500 0
B 3 500 0 350 000 2 000
C 350 000 2 000 3 500 000 20 000
D 3 500 000 20 000 not defined not defined
Airborne particulate classification for manufacture of sterile pharmaceutical
preparations
B- Processing
8/9/2019 Dosage Form I
61/229
B- Processing
1- Cleaning of equipment and containers.
2- Compounding the product.
3- Filtration of solutions: Solutions are filtered for:- Clarification from particles of size down to 3 m.
- Sterilization by removal of particles down to 0.3 m.
4- Filling procedures:
Liquids are more easily filled than solids.
Low density liquids are more easily filled than high densityor sticky liquids.
The size of delivery tube is governed by :
- the opening of the container.- The viscosity and density of liquid.
- The speed of delivery.
A retraction device is fitted to the filling machine to remove
8/9/2019 Dosage Form I
62/229
A retraction device is fitted to the filling machine to remove
the hanging drop during filling to prevent wetting the neck
of the container which may cause breakage during sealing.
LVPs are filled by gravity as they do not need precision
( containing no potent drugs).
Pressure pump fillers ( semi-automatic) : for liquids.
Vacuum pump fillers (Automatic) : for powders.
Emulsions and suspensions require steam-jacketed (to
decrease product viscosity) and constantly stirred reservoir
(to prevent sedimentation of suspended particles) duringfilling.
Filling of powders:
8/9/2019 Dosage Form I
63/229
Filling of powders:
Fine powder has slow and irregular flow ( air pockets andelectrostatic charges)
Small granular particles, with narrow size distribution, ( toavoid segregation) are more flowable.
5- Sealing:
Containers should be sealed in aseptic area near filling
Ampoules are sealed by melting a portion of the glass neck to formeither tip-seal or pull-seal.
Excessive heating is not recommended due to expansion of air againstthe soft glass forming fragile bubbles at the point of seal.
Fracture of the wet ampoule neck may occur during sealing.
Sealing of vials and bottles Rubber closures must fit container opening and secured by aluminum
caps having a centre that is torn away at the time of use.
C- Preparation of parenterals
8/9/2019 Dosage Form I
64/229
C- Preparation of parenterals
1- Parenteral Solutions
Dissolving the drug and preservative, adjusting the pH and
sterile filtering the solution through a 0.2 m membranefilter.
Pre-filtration through a coarser filter may be necessary to
maintain adequate flow and prevent blocking.
The sterile filtrate is aseptically filled in the final containers.
Whenever possible, it is preferable to terminally sterilize the
product by autoclaving if the drug is thermostable.
2- Parenteral Suspensions
8/9/2019 Dosage Form I
65/229
2- Parenteral Suspensions
Suspensions require a balance of ease of filling and storage
without caking and ease of passage through syringe
(syringeability and injectability). Therefore, it is necessary to control particle size, particle size
distribution, rheologicalproperties and wettability.
A formula for parenteral suspension should contain:
- Active ingredient suspended in aqueous vehicle containing preservative.- A suspending agent as Aluminum monostearate, gelatin, mannitol,
povidone or sorbitol.
- Surfactants as wetting agent and to prevent crystal growth such as
Tween 80 and lecithin.
- Buffer for adjusting pH as citrate buffer.
Methods of preparation: Two methods
8/9/2019 Dosage Form I
66/229
Methods of preparation: Two methods
1-The aqueous vehicle containing the soluble ingredients is
sterilized by heat or filtration. The sterile drug powder
(procain penicillin G) prepared by freeze-drying, sterilecrystallization or spray drying is added to the sterile vehicle
and aseptically filled.
2- The sterile drug (testosterone) solution in acetone isprepared and aseptically added to the sterile aqueous
vehicle, leading to crystallization of the drug. The crystals are
allowed to settle and the supernatant is siphoned off. The
crystals are washed several times with sterile aqueous
vehicle and finally adjusted to volume, then filled aseptically
in the final containers.
3- Parenteral Emulsions
8/9/2019 Dosage Form I
67/229
3 Parenteral Emulsions
It is not recommended to prepare emulsions for IV
administration because:
a) The emulsion droplet size should be less than5 m (to prevent blood emboli) which is difficult.
b) Selection of emulsifiers and stabilizers is limited.
Among the few examples of parenteral emulsions in the
market is 10% Soybean oil (o/w) for IV parenteral nutrition(TPN). It contains Eggyolk phospholipid as emulsifier and
glycerin as stabilizer.
Oil soluble vitamins (E) is available as o/w IM emulsion.
The parenteral emulsions are usually sterilized byautoclaving.
8/9/2019 Dosage Form I
68/229
8/9/2019 Dosage Form I
69/229
8/9/2019 Dosage Form I
70/229
3- Leaker testing:
8/9/2019 Dosage Form I
71/229
3 Leaker testing:
The tested ampoules are immersed in 1% methylene blue,
vacuum is applied for 15 min., then released rapidly.
Defective ampoules show blue colour.
4- Alkalinity testing:
The tested ampoules are either filled with or crushed and
immersed in distilled water, autoclaved and titrated against0.01 M HCl using methyl red indicator
The consumed HCl is a measure for the glass alkalinity
dissolved in water.
8/9/2019 Dosage Form I
72/229
RADIOPHARMACEUTICAL
Chapter II
RADIOPHARMACEUTICALS
8/9/2019 Dosage Form I
73/229
RADIOPHARMACEUTICALS
Radiopharmaceuticals are dosage forms which incorporate a
radionuclide ( radioactive isotope ) .
Atomic structure:
A neutral atom consists of a positively charged nucleus
composed ofprotons and neutrons and surrounded by negative
electrons.
Atomic number (Z) = number of Protons = number of electrons.
Mass number (A) = number of protons + number of neutrons.
The nucleus with its protons and neutrons is called nuclide
which is given the symbol z XA
8/9/2019 Dosage Form I
74/229
Isotopes:
These are nuclides of the same chemical element,possessing the same number of protons but with
different number of neutrons.
Therefore isotopes have the same atomic number anddifferent mass number.
e.g. 1H1 (hydrogen)2 H1 (deuterium)
and 3H1 ( tritium)
Isobars:
8/9/2019 Dosage Form I
75/229
Isobars:These are nuclides of different elements, possessing the same
mass number
e.g. 3H1 and3 H2
Isotones :
These are nuclide of different elements, possessing the samenumber of neutrons.
e.g. 3H1 and4H2
Radioactivity :
8/9/2019 Dosage Form I
76/229
y
It is the process in which unstable nuclei with excess energy are
changing spontaneously and emitting energy in the form of
particles, electromagnetic waves or both. Such radioactive nucleiare called "radioisotopes" and the process of nuclear
transformation is called "radioactive decay"
Types of radiation from radioisotopes:
Three types of radiation are emitted most frequently fromradioactive nuclei. These are:
1- Alpha particles ( 42) :
An particle consists of two protons and two neutrons. Thus it isidentical to the helium nucleus 4H2 It has a penetration power of about 5 cm in air and less than 0.1
mm in tissues.
2-Beta particles (+1 and 1)
8/9/2019 Dosage Form I
77/229
2 Beta particles ( +1 and -1)
These have two kinds,
positron (+1 ) and negatron (-1).
They have a penetration power of about 3 cm in air
and about 1 mm in tissues.
3-Gamma radiation ( y ) :
Gamma radiation is electromagnetic waves having a
high penetration power which can reach up to about 1km in air and about 25 cm in tissues
Types of radioactive decay:
8/9/2019 Dosage Form I
78/229
Types of radioactive decay:
1- Alpha decay:
It occurs in heavy nuclide having atomic numbers > 82 . In this
decay alpha particle is emitted as follows:238U 92 (uranium)234 Th 90 (Thorium) +
4 He 2
2- Beta decay
It has two types:
a) Negatron decay: In this decay, a negatron and a neutrino (v) are
emitted: e.g.32P15
32S16 + -1 + v
It can be explained as follows:
A neutron is converted to a proton with the release of a negatronand a neutrino is illustrated by the following particle reaction:
1n01P1 + -1 + v
8/9/2019 Dosage Form I
79/229
The decay of phosphorus 32 of energy E1 to sulphur 32 of energyE2 is represented by an energy level diagram as as shown in the
figure. Such decay is associated with the release of energy equal to
E. where E = E 1 - E2.
The energy released (E) was found to be greater than the energyof the particle and therefore. a new particle, the neutrino was
postulated to account for the balance of the energy so that the sum
of the energies of the beta particle and its associated neutrino is
equal to E .
b) Positron decay: In this decay a positron and a
8/9/2019 Dosage Form I
80/229
b) Positron decay: In this decay. a positron and a
neutrino are emitted as follows
11C6 (carbon)11B5 (boron) + +1 + v
Here, a proton is converted to a neutron with the
release of a positron and a neutrino. A neutrino is also
required here to account for the balance of the energy.
The corresponding particle reaction is :
1
P11
n0 + +1 + v
3 Electron capture decay:
8/9/2019 Dosage Form I
81/229
3- Electron capture decay:
Here, the nucleus capture an orbital electron and a
proton is converted to a neutron with the release of
gamma rays as follows:
7
Be4 (Berilium) +0
e-17
Li3 (lithium) + y
The following particle reaction occurs:
1P1 + 0e-1 1n0 + y
4- Isomeric transition:
8/9/2019 Dosage Form I
82/229
4 Isomeric transition:
In this reaction, an unstable nuclide. with a high energy decays
to a suitable isomeric nuclide of lower energy with the emissionof gamma rays.
Here, protons and neutrons are rearranged within the nucleus
leading to change in energy level of the nuclide.
The more excited isomeric state is called metastable state which
is indicated by adding the letter" m " to the mass number
e.g. metastable technetium 99m Tc
99m Tc 99Tc + y
Units of radioactivity :
8/9/2019 Dosage Form I
83/229
y
A) Activity units
1- Curie (Ci) : it is the quantity of a radionuclide that is decaying at
a rate of 3.7 x 1010 disintegrations per second (dps) .
1curie =3.7 x 1010 dps
2- 1 millicurie (mCi) =3.7 x 10 7 dps
3- 1 microcurie (Ci) = 3.7 x 10 4 dps
* Specific activity: it is the radioactivity contained in 1 g or 1 ml ofthe radionuclide e.g. 50 mCi / g of 131 I
B) Dose units :
8/9/2019 Dosage Form I
84/229
B) Dose units :
1- Exposure dose:
Exposure dose is measured in Roentgen.
Roentgen :It is the quantity of X - or gamma radiation which
will produce one unit of charge of either sign in 1 cm3
of air
Thus the roentgen is a unit of exposure dose to X - or gamma
radiation which is the commonly used in radiotherapy. The
roentgen is not a unit of or radiation which is rarely used
2 Absorbed dose:
b b d d i d i " d " " "
8/9/2019 Dosage Form I
85/229
Absorbed dose is measured in " rad " or "Gray"
Rad : It is the dose of ionizing radiation that results in
absorption of an energy of 100 ergs / g of material.
An exposure of 1 roentgen delivers an absorbed dose of
approximately 1 rad.
Equal absorbed doses of different types of radiation mayproduce different biological effects. Therefore each kind of
radiation has what is called quality factor " Q" ,which is a number
representing the relative biological effectiveness of a particular
kind of radiation. For example, "Q" for alpha particle = 20 and "Q"for neutron = 10 .
The absorbed dose in " rad" multiplied by the quality factor "Q" is
called radiation equivalent dose "rem".
Rate of radioactive decay:
R f di i d i d fi d h b f f h
8/9/2019 Dosage Form I
86/229
Rate of radioactive decay is defined as the number of atoms of the
nuclide disintegrating per unit time. It may be expressed by the
following equation:
dN / dt = - N and in the logarithmic form
log N = log No - t /2.303
Where : N = Number of radioactive atoms present at time t
No = Number of radioactive atoms present at zero time
= decay constantThe rate of decay is also called" activity" and its equation may be
written as ;
Log A = log Ao - t/ 2.303
The decay of radioactive atoms is a first order reaction whereplotting log N versus time gives a straight line
with a slope = / 2.303 and
an intercept = log No
8/9/2019 Dosage Form I
87/229
The half - life of a radioactive nuclide is the time required for
one half of a given number of atoms to decay. It can be
obtained from the following equation:
t 0.5 = 0.693 /
The half - life can vary from a fraction of second up to millions
of years.
8/9/2019 Dosage Form I
88/229
Problem:
8/9/2019 Dosage Form I
89/229
A patient requires 500 Ci of radioactive iodine on 25 - 5 - 2013 ,
how many ml are required from the previously mentioned bottle
of Na 1131
Solution:
Ao = 5.4 mCi / ml = 5.4 X 1000 Ci / ml
Time from 1-4-2013 to 24-5-2013 = 55 days
log A = log Ao - t /2.303
= log ( 5.4 X 1000) - 0.012 X 55/2.303
A = 2786.12 Ci / ml
500 Ci X ml
X ( number of ml required) = 500 / 2786.12 = 0.18 ml
Problem:
On 1 12 2013 a radiopharmacist was asked to prepare a gold (AU198) injection
8/9/2019 Dosage Form I
90/229
On 1 -12- 2013 , a radiopharmacist was asked to prepare a gold (AU198) injection
containing 500 Ci / 2ml . how can he proceed to prepare such injection if he has a
gold bottle with the following data :
Ao = 100 mCi / ml Manufacturing date = 1 - 10 2013t 0.5 = 0.798 month
Solution:
Ao = 100 mCi / ml = 100,000 Ci / ml Time = 2 months
= 0.693/ 0.798 = 0.868 month-1
log A = log Ao - t/2.303
= log 100000 - 0.868 X 2/ 2.303 = 4.246
A = 17620 Ci / ml
17620 Ci 1 ml
500 Ci X ml
X = 0.028 ml
The pharmacist takes 0.028 ml and complete to 2 mf with water for injection to
obtain an injection containing 500 Ci / 2ml
Sources of radioisotopes
8/9/2019 Dosage Form I
91/229
p
1- Natural sources:
Naturally occurring radioisotopes are those that were formedwith the earth and decay so slowly that they are still present
today e.g. Uranium-238 , and potassium-40 . They disintegrate
through a series of decay processes until stable nuclear
configuration are reached.
2- Artificial sources:
a) By fission :
Certain heavy radionuclide like U238 can be caused to fission by
introduction of a neutron into the nucleus leading to theproduction of radioactive fission products like I131 . This process is
performed in a nuclear reactor.
b)
By activation:
8/9/2019 Dosage Form I
92/229
b) By activation:
Many radioactive nuclides are prepared by neutron activation
by placing a suitable target element in a nuclear reactor where
it is bombarded by neutrons. For example, radioactive
Phosphorus (32p) can be prepared by neutron bombardment of
the stable phosphorus (31p) or sulphur ( 32S ).
c) By acceleration (Cyclotron produced isotopes):Certain radioisotopes are produced by accelerating charged
particles like protons, deutrons or alpha particles in an
accelerator by applying a high voltage.
The highly energetic accelerated particles are caused to
bombard a target element. I123 is an example of this type. It is
obtained by proton bombardment of I127
Radioisotope generator
8/9/2019 Dosage Form I
93/229
p g
These are used to produce short half-life radioisotopes from
long half-life ones. Short half-life radioisotopes are used in internally administered
radio pharmaceuticals to minimize the radiation dose received by
the patient.
A radioisotope generator is an ion exchange column containing
a resin or alumina upon which has been adsorbed a long-lived
parent radionuclide.
Radioactive decay of the long-lived parent nuclide results in theproduction of a short-lived radioactive daughter nuclide which is
eluted from the column by means of an appropriate eluent (in
which the parent nuclide is insoluble) .
8/9/2019 Dosage Form I
94/229
An example is the technetium-99 generator in which the
parent radionuclide molybdenum-99 is adsorbed on an
alumina column.
Radioactive decay of molybdenum-99 produces
technetium-99 which is eluted from the column with sterile,
pyrogen free saline solution.
8/9/2019 Dosage Form I
95/229
APPLICATIONS OF RADIOISOTOPES
8/9/2019 Dosage Form I
96/229
APPLICATIONS OF RADIOISOTOPES
A radiopharmaceutical is a preparation intended for
therapeutic or diagnostic purposes, containing a radionuclide
in the form of an element , a simple salt or a complex and
may exist in the form of a solid, liquid or gas. They have the
following applications :
A - Therapeutic applications:
For therapy, isotopes are used as radiation sources either
externally or internally.
1- External radiation sources :
8/9/2019 Dosage Form I
97/229
a) Teletherapysources e.g. Cobalt-60 and Cesium-137 have been
used for the treatment of lesions.
b) Surface sources e.g. Phosphorus-32 and Strontium-90
2- Internal radiation sources :
a) Gold (198Au ):introduced as a colloidal gold suspension into the cavities
containing the serous fluid. it will be localized on the surface of
the cavity as large aggregates or precipitate e.g. in the treatment
of peritoneal and pleural effusion associated with malignanttumours.
It has been used in treatment of prostate and cervix uterine
carcinoma and bladder tumours.
b) Sodium phosphate ( 32 P ):
8/9/2019 Dosage Form I
98/229
b) Sodium phosphate ( P ):
may be used to decrease the rate of formation of
erythrocytes, where the isotope is concentrated in the
cancerous tissues. It may be also utilized in the treatment ofchronic granulocytic leukemia.
c) Sodium iodide (131I ):
In cases of hyperthyroidism, therapeutic doses of iodine-131will destroy thyroid tissues by means of radiation produced
within the gland. This procedure is better than X-ray
treatment since there is less radiation danger to the
surrounding tissues.
B- Diagnostic applications;
F di i i t d di ti t t
8/9/2019 Dosage Form I
99/229
For diagnosis, isotopes are used as radioactive tracers not as
radioactive sources. Differences between radioactive tracers and
sources are shown in the following table :__________________________________________________________________
adioactive sources Radioactive tracers
_______________________________________________________
1- Pharmacologically active Pharmacologically inactive
2- Administered in large doses Administered in very small doses3- They are long half-life isotopes Short half-life isotopes
e.g. 60CO, 137Ci , 90Sr e.g. 57Co , 51Cr, 24Na
_______________________________________________________
Diagnostic applications involve the following techniques:
8/9/2019 Dosage Form I
100/229
g pp g q
1 Isotope dilution:
This technique is used for measuring blood volume.
Radioiodinated human serum albumin is injected IV and
after 10 min a blood sample is withdrawn and itsradioactivity is measured .
The blood volume is calculated from the measured
decrease in radioactivity of the injected sample upon itsdilution by the blood.
2- Isotope disappearance rate:
8/9/2019 Dosage Form I
101/229
This technique is used for measuring half life of RBCs.
A blood sample is withdrawn and its RBCs are labeledwith 51Cr and then re-injected .
The rate of disappearance of the labeled cells can be
determined by measuring radioactivity of blood
samples taken every 2 or 3 days for at least 2 weeks.
The normal RBC half-life = 30 - 33 days. In hemolyticanemia . RBC half-life = 1 - 7 days.
3- Isotope transfer rate:
Thi h i i d d i i l i i i ll i
8/9/2019 Dosage Form I
102/229
This technique is used to determine circulation time especially in
the extremities.24
Na is injected into one part of the vascular system and the timerequired for its arrival at another part is determined.
4- Isotope uptake:
The concentration of a particular isotope in an organ can be used
as a measure of the function of that organ e.g.a) Thyroidfunction is measured by determining the thyroid uptake
of 131 I after oral administration of Na 131 I
b) Liverfunction is measured by determining the liver uptake of
131I after intravenous injection of rose bengal with 131 I .c) Renal function is measured by determining the renal uptake of
131 I after intravenous injection of iodopyracet with 131l or
iodohippurate with 131 I
5- Scanning technique:
By this technique tissues and organs can be visualized to detect
8/9/2019 Dosage Form I
103/229
By this technique, tissues and organs can be visualized to detect
abnormalities in their function.
Scanning technique consists of the following steps:
- Administration of a radionuclide.
- Concentration of the radionuclide in a certain organ or tissue.
- Making an image of the organ or tissue.
The following are examples of radioisotopes used in such
technique:
Na131
I is used for scanning of thyroid gland. Rose bengal 131I is used for scanning of liver.
Sodium iodohippurate 131 I is used for scanning of kidney.
RBCs labeled with 51Cr is used for scanning of spleen.
C- Pharmaceutical applications:
8/9/2019 Dosage Form I
104/229
Radioactive isotopes are used in the field of
biopharmaceutics and pharmacokinetics for the
determination of :
Dissolution rate and disintegration time of solid
dosage forms.
Rate of absorption, distribution, metabolism and
excretion of drugs in body.
Harmful effects of radiation
8/9/2019 Dosage Form I
105/229
1-Biological effects
a) Inactivation of essential enzymesb) Coagulation of proteins
c) Damage of nucleic acids
d) Release of histamine like substances
2-Skin effects
a) Short exposure to intense radiation produces
erythema
b) Long exposure to low radiation causes brittleness and
dryness of the skin, loss of hair and burns
3 Somatic effects
8/9/2019 Dosage Form I
106/229
3- Somatic effects
These effects occur from about 2 months to many
years after exposure. They include:
Cataract, severe anemia, leukemia and cancer
4-Genetic effectsRadiation has 2 effects on reproductive cells:
a) Damage of chromosomes
b) Increase in frequency of gene mutation
Maximum permissible exposure
8/9/2019 Dosage Form I
107/229
a) External exposure
The external exposure is calculated by the maximumpermissible dose (MPD) which differs according to the
organ to be exposed as follows:
1- MPD for critical organs like eyes = 5 rems / year2- MPD for arms, feet and ankles =25 rems /year
3- MPD for skin and other organs = 10 rems / year
8/9/2019 Dosage Form I
108/229
Precautions for radioprotection
h d d l k h f ll
8/9/2019 Dosage Form I
109/229
Each individual must keep the following precautions:
1- Keep the exposure as low as possible
2- Keep the isotope laboratory clean and neat and the workingarea should be free from equipment not required for the process
3- Keep the finger nails short and clean and avoid working with
the skin broken and avoid eating or smoking in the isotope
laboratory
4- Wear the prescribed monitoring equipment (pocket
dosimeter ).
5- Wear protective clothing, gloves and respiratory protective
devices.
6- Use pipette filling devices and perform the work within aconfined area.
7 - The radioactive material must be kept in double containers .
Chemical protective agents
8/9/2019 Dosage Form I
110/229
p g
1- Injection or ingestion of compounds containing
sulfhydryl group e.g. certain amino acids.
2- Administration of a large dose of a non radioactive
compound of similar composition as the radionuclide to
allow in-vivo exchange between the two compounds.
3- The use of a blocking dose or a dose which enhance
excretion of the nuclide e.g. high dose of 32 P is treated
by large dose of stable P and Ca ions.
8/9/2019 Dosage Form I
111/229
8/9/2019 Dosage Form I
112/229
OPHTHALMIC PREPARATIONS
Ophthalmic preparations are sterile products
essentially free from foreign particles, suitably
compounded and packaged for installation intothe eye.
They may be in the form of Solutions,Suspensions, Ointments or solid dosage forms
Absorption of drugs in the eye
8/9/2019 Dosage Form I
113/229
When a quantity of topical ophthalmic dosage form is applied to
the eye, several factors affect the availability of the drug :
1- Normal application of two drops (100l) on a tear volume of
30 I , means that 70% of the administered volume can be
expelled from the eye by overflow since the capacity of the eye isonly 30 I.
If blinking occurs, the residual volume of 10 I indicates that 90%
of the administered volume will be expelled.
2- Drainage of the administered drop via the naso-lcrimal
8/9/2019 Dosage Form I
114/229
2 Drainage of the administered drop via the naso lcrimal
system into the gastrointestinal tract begins immediately
upon installation.
3- A third mechanism competing for drug absorption into the
eye is the superficial absorption of the drug into conjunctiva
with rapid removal from the ocular tissues by the peripheral
bloodstream.
4- In competition with the three foregoing forms of drug
l f th l ti i th t l b ti
8/9/2019 Dosage Form I
115/229
removal from the ocular tissues, is the trans-corneal absorption
of the drug.
For topically administered drug, to traverse the intact cornea
and to appear in the aqueous humor, it must possess dual or
differential solubility.
This differential solubility characteristic, depending upon the pH
of the environment, causes the drug molecule to exist in
equilibrium with its ionized form.
The non-ionized and ionized forms of the drug can penetratethe three layers of the cornea ( lipid-rich epithelium, lipid-poor
stroma and lipid-rich endothelium) as shown in the figure.
8/9/2019 Dosage Form I
116/229
8/9/2019 Dosage Form I
117/229
Penetration of an alkaloid through the intact comes by
differential solubility
Pharmacologic Categories of Ophthalmic Drugs
8/9/2019 Dosage Form I
118/229
Topical anesthetics: as tetracaine, are employed to provide
pain relief preoperatively, postoperatively, for ophthalmic
trauma, and during ophthalmic examination.
Antibiotic / Antimicrobial Agents: as gentamicin, are used
systemically and locally to combat ophthalmic infection.
Antifungal Agents: as amphotericin B, are used topically
against fungal endophthalmitis and fungal keratitis.
Steroidal anti-inflammatory Agents: as dexamethasone, areused to treat inflammation of the eye, as allergic conjunctivitis.
Non-steroidal anti-inflammatory agents: as diclofenac, are used
to relief ocular inflammation
8/9/2019 Dosage Form I
119/229
to relief ocular inflammation.
Antiviral Agents: as vidarabine, are used against viral infections,
as that caused by herpes simplex virus.
Astringents: as Zinc sulfate, are used in the treatment of
conjunctivitis.
Beta-Adrenergic Blocking Agents: as timolol maleate, are used
topically in the treatment of elevated intraocular pressure (lOP)
and chronic open angle glaucoma.
Miotics: as pilocarpine, are used in the treatment of glaucoma,
Mydriatics allow examination of the fundus through the dilation
of the pupil (atropine).
Cycloplegics are long acting mydriatics.
8/9/2019 Dosage Form I
120/229
Protectants / Artificial Tears: as carboxymethyl cellulose
solutions employed as artificial tears or as a contact lens fluids to
lubricate the surface of the eye.
Vasoconstrictors / Decongestants: as oxymetazoline
When applied topically to the mucous membranes of the eye
cause transient constriction of the conjunctival blood vessels. Theyare intended to soothe, refresh, and remove redness due to minor
eye irritation.
Anti-histamines :as pheniramine maleate, are included in someproducts to provide relief of itching due to pollen and ragweed.
Factors affecting ocular bioavailability:
8/9/2019 Dosage Form I
121/229
I. Physiologic factors which include:
Protein binding:
Normally, tears contain 0.6 - 2.0% of albumin and globulins, and
in disease states, these protein levels are raised. Large size drug-
protein complex has a difficulty in penetrating the cornea.
lacrimaldrainage: Due to lacrimal drainage, a brief time is
available for a drug to remain in the eye leading to a
considerable decrease in absorption.
Drug metabolism:
Like other biological fluids, tears contain lysozyme enzymes
capable of the metabolic degradation of drugs.
II. Physicochemical characteristics of drug and product formulation:
8/9/2019 Dosage Form I
122/229
A- Drugs having lipophilicand hydrophiliccharacters are able to
penetrate the Cornea (corneal membrane contains both lipophilicand hydrophilic layers).
B- Ophthalmic suspensions, gels, and ointments mix less readily
with lacrimal fluids than low-viscosity solutions with the
consequent longer contact with ocular tissue and enhanced
bioavailability.
Types of ophthalmic products
8/9/2019 Dosage Form I
123/229
1- Ophthalmic Solutions
It is the most common means of administering drugs to the eye.
All ingredients are completely soluble and there is little physical
interference with vision.
The main disadvantage of solutions is the short contact time
with the absorbing surface
The selection of the appropriate drug salt depends on :
- Its solubility - therapeutic concentration- ocular toxicity - buffer capacity
- effect on pH and tonicity
- its discomfort reactions (stinging or
burning sensation).
An example for the effect of drug salt on the product properties
is the Epinephrine solution :
8/9/2019 Dosage Form I
124/229
is the Epinephrine solution :
a- The bitartrate forms solution has a pH range of 3-4 ,but has a
high buffer capacity causing considerable stinging due to the free
carboxyl group.
b- The borate salt has lower buffer capacity, a more nearly
physiological pH and only mild stinging, but less stable.
c- The hydrochloride salt combines better stability than borate
and acceptable pH and stinging.
Therefore, Epinephrine hydrochloride is the salt of choice.
2- Ophthalmic suspensions:
8/9/2019 Dosage Form I
125/229
If the drug is not sufficiently soluble, it can be formulated as a
suspension.
A suspension may also be desired to improve stability,
bioavailabilitv, or efficacy.
The major topical ophthalmic suspensions are the steroid anti-inflammatory agents: Prednisolone acetate and Dexamethazone.
Water soluble salts of prednisolone phosphate and
dexamethazone phosphate are available however, they have a
lower potency and are poorly absorbed.
An ophthalmic suspension should use the drug in a microfine
form, usually 90 % or more of the particles having a diameter of 10
m or less , to avoid irritation of the sensitive ocular tissues and to
ensure uniform dosage delivery,
3- Sterile powders for reconstitution:
8/9/2019 Dosage Form I
126/229
Several ophthalmic drugs are prepared as sterile powders for
reconstitution before dispensing to the patient. These include
Chloramphenicol, Epinephrine and Tetracycline hydrochloride.
The sterile powder is usually manufactured by lyophilization and
is packaged separately from the diluent, and a sterile dropper is
provided.
In powder form, these drugs are more stable (longer shelf-life)
than solution form.
Each product has an expiration date for the
reconstituted solution which should be explained to
8/9/2019 Dosage Form I
127/229
reconstituted solution which should be explained to
the patient with the proper storage conditions and
method of usage.
The sterile powders may contain:
Inert bulking agent such as Mannitol.
Co-drying agent as potassium acetate is used to
improve stability of the extremely moisture sensitive
drugs such as Echothiophate iodide ( choline estrase
inhibitor for treatment of glaucoma ).
4- Ophthalmic Ointments:
8/9/2019 Dosage Form I
128/229
The ointment vehicle is usually a mixture of mineral oil and
whitepetrolatum.
The main advantages of the petrolatum-based ointments are:
1- Their inertness and anhydrous nature which make them
suitable vehicles for moisture-sensitive drugs.
2- They offer longer contact time and greater drug bioavailability.
The main disadvantages of ophthalmic ointments are:
1- greater dosage variability than solution.
2- Blurring of vision ( therefore used at nighttime ).
The anhydrous petrolatum base may be made more miscible
with water through the use of an anhydrous liquid lanolin
8/9/2019 Dosage Form I
129/229
with water through the use of an anhydrous liquid lanolin
derivative. Drugs can be incorporated into this type of base in
aqueous solution.
Ophthalmic ointments are usually manufactured from
sterilized ingredients under aseptic conditions, and should
meet the requirements of the official sterility tests.
Preservatives such as chlorobutanol,parabens , and
phenylmercuricacetate and nitrate are commonly used
(especially chlorobutanol ).
The drug is added to the ointment base either as a solution or
as a micronized powder. The finished ointment must be free
from large particles.
5- Ocular Inserts (Ocuserts) :
They are drug containing devices that deliver one or more drugs at
8/9/2019 Dosage Form I
130/229
They are drug-containing devices that deliver one or more drugs at
a programmed rate, for a prescribed period of time to provide
continuous control of drug therapy.
Pilocarpine ocusert is an example of this type of solid dosage form.
It consists of three parts:
1- The drug reservoir mixed with a carrier material (alginic acid) .
2- A rate controller, ethylene/vinyl acetate copolymer
membrane
3- The platform consists of annular ring of the membrane
impregnated with titanium dioxide that forms whiteboarder for visibility.
The ocusert system provides a nearly steady zero-order
delivery rate of pilocarpine from the unit for 7 days when placed
8/9/2019 Dosage Form I
131/229
delivery rate of pilocarpine from the unit for 7 days when placed
in the aqueous tear environment of the eye.
Advantages:
1- The ocusert exposes the patient to only one- fourth to one-
eighth the amount of pilocarpine compared to drop therapy. This
could lead to reduced local side effects and toxicity.
2- It provides a continuous around-the-clock control of
intraocular pressure (lOP).
3- It provides more patient convenience and improved
compliance, as the dose is administered only once per week.
4- It is a good alternative for patients sensitive to preservatives.
Disadvantage:
The patient must check periodically to see that the unit is still in
8/9/2019 Dosage Form I
132/229
place. Replacement of contaminated unit
fresh one is very expensive
a.
8/9/2019 Dosage Form I
133/229
FORMULATION AND PREPARATION OF OPHTHALMIC PRODUCTS
8/9/2019 Dosage Form I
134/229
Ophthalmic solutions are formulated to be sterile isotonic and
buffered for stability and comfort. A viscosity imparting agent
may or may not be present. Solutions must be free from foreign
particles.
The proper pH (optimum drug stability), buffer and buffer
capacity should offer drug stability and comfort of the eye ( pH oftear is about 7.4 ). Therefore, buffer capacity should be sufficient
to maintain pH but minimized to the point where tear fluid can
overcome capacity and readjust the pH to 7.4 immediately after
instillation in the eye.
Buffering and pH adjustment:
8/9/2019 Dosage Form I
135/229
Ideally, an ophthalmic product should have a pH of
7.4 ( physiological pH of tear fluid ).
But the tear fluid has some buffer capacity which can
adjust the pH of the instilled product if the volume ofsolution is not excessive and does not have a strong
resistance to neutralization (minimum buffer
capacity).
Tonicity adjustment:
8/9/2019 Dosage Form I
136/229
An ophthalmic solution is considered isotonic when
it has an osmotic pressure equal to that of tear fluid(equal to that of 0.9 % sod. chloride solution).
In formulation of ophthalmic preparation, it is more
important to consider the sterility, stability,and
preservation rather than isotonicity.
It was found that the eye can tolerate solutions
equivalent to 0.5 % 1.8 % sod. chloride.
In some cases, the therapeutic concentration of the
drug necessitates using hypertonic preparation ,ex. Sod.
8/9/2019 Dosage Form I
137/229
drug necessitates using hypertonic preparation ,ex. Sod.
Sulfacetamide which is used in a concentration range of
10% - 30 % , while the isotonic solution should containonly 3.5 % of the drug.
The tonicity adjusting ingredients usually used
include: NaCI - KCI Buffer salts - Dextrose - glycerin -
propylene glycol.
Viscosity - imparting agents
8/9/2019 Dosage Form I
138/229
The USP permits the use of viscosity increasing agent to
prolong the contact time in the eye and thus enhance drugabsorption and bioavailability.
A secondary benefit of the polymer solution is a lubricating
effect.
The major commercial viscous polymers used are Polyvinyl
alcohol ( Liquifilim) and hydroxvpropylmethylcellulose ( Isopto ) .
The first polymer has viscosity of 4 - 6 cp at a concentration of
1.4 % , while the second has a viscosity of 10- 30 cp at aconcentration of 0.5 % depending on the pH and ionic
concentration of the product.
Preservatives and their choice
8/9/2019 Dosage Form I
139/229
The limited choice of preservative agents is narrowed
when the requirements of chemical and physicalstability and compatibility are considered for a particular
formulation and package.
The choice of preservative is limited to only a fewchemicals that have been found over the years to be
safe and effective for this purpose.
a- Benzalkonium chloride:
8/9/2019 Dosage Form I
140/229
It is the most widely used preservative, generally used in
combination with disodium edetate .
It is rapidly acting and stable over wide range of pH even at
hot storage conditions.
It has pronounced surface active properties, but incompatible
with nitrates, salicylates , anionic soaps and fluorescein.
The usual concentration range used in eye drops is 0.004 -
0.02 % ( 0.01 % ). A 0.03 % solution is used as a penetrationenhancer for some drugs in addition to its preservative activity.
b- Organic mercurials :
8/9/2019 Dosage Form I
141/229
When benzalkonium chloride cannot be used, one of the
organic mercurials , Phenymercuric nitrate (PMN),Phenylmercuric
acetate (PMA) or Thimerosal is used.
They are relatively weak and slow in their antimicrobial activity.
They are restricted to use in neutral to alkaline or slightly acidic
solutions.
Phenylmercuric ions are incompatible with halide ions forming
salts of lower solubility and effectiveness. Thimerosal has greater
solubility and is more stable than phenylmercuric compounds.
The usual concentration ranges are 0.002 - 0.004 %for PMN and
PMA, and 0.005 - 0.02 % ( but usually 0.01 % ) for thimerosal
c- Chlorobutanol.-
8/9/2019 Dosage Form I
142/229
It has relatively slower activity, but acceptable stability at
room temperature when used in acidic solution around pH 5 orbelow.
If autoclaved at pH 5 , it will decompose about 30% resulting in
HCl and the pH will further decrease by time.
The use of chlorobutanol necessitates the use of glass
package, because being volatile it will permeate the
polyethylene plastic containers.
It is used in a concentration of 0.5 % .
d- Methyl and Propylparabens .-
They are esters of para hydroxybenzoic acid used mainly to
8/9/2019 Dosage Form I
143/229
They are esters of para-hydroxybenzoic acid used mainly to
prevent mold growth, but in higher concentrations ( weak
antimicrobial activity).
They have low water solubility causing stinging and burning
sensation in the eye.
They bind to a number of nonionic surfactants and polymers,
reducing their bioactivity.
They are used as combinations, in a concentration of 0.03 - 0.1
% for methyl ester and 0.01 - 0.02 % for propyl ester.
e- Phenylethyl alcohol.-
8/9/2019 Dosage Form I
144/229
y y
In addition to its weak activity, it is volatile andwill lose activity via permeation through plastic
package.
It has limited water solubility, and can produceburning and stinging sensation in the eye.
It is recommended to be used in combination
with other preservatives in a concentration of 0.5
%
Other additives
a- Antioxidants:
S di bi lfi bi lfi i i d i i
8/9/2019 Dosage Form I
145/229
Sodium bisulfite or metabisulfite is permitted in concentration
up to 0.3 % especially for preparations containing epinephrine.
Other antioxidants have been developed such as ascorbic acid
and acetylcysteine , sodium bisulfite and 8-hydroxyquinoline.
b-Surfactants: The use of surfactants in ophthalmic preparations is restricted.
Nonionic surfactants , the least toxic class, are used in low
concentrations to achieve solution clarity.
Nonionic surfactants may react with some antimicrobials
lowering their effect.
Cationic surfactants such as benzalkonium chloride are mainly
used for their preservative effect.
PACKAGING OF OPHTHALMIC PRODUCTS
E d k d l t i l ti d b ttl A f
8/9/2019 Dosage Form I
146/229
Eye drops are packaged almost in plastic dropper bottles. A few
products still remain in glass dropper bottles because of special
stability considerations.
The main advantages of plastic bottles are:
1- Convenience of usage by the patient.
2- Decreased contamination.
3- Lower weight and cost.
8/9/2019 Dosage Form I
147/229
LDPE is compatible with a wide range of drugs and
formulation components, but the main disadvantage is:
8/9/2019 Dosage Form I
148/229
its sorption andpermeability characteristics.
The sorption and permeability can be detected by the stability
studies. If the permeating component is preservative such as
chlorobutanol or phenylethyl alcohol , a safe and reasonable
excess of the permeable component may be added to balance
the loss over the shelf- life.
LDPE resins are translucent and, if the drug is light -sensitive,
additional package protection may be required. This may be
achieved by using a resin containing an opaquing agent such astitanium dioxide ,by placing an opaque sleeve over the
container, or by placing the bottle in a cardboard carton.
LDPE resin used for the bottle and the dispensing tip cannot be
autoclaved and they are thus gas sterilized usually with ethylene
oxide-freon mixture.
8/9/2019 Dosage Form I
149/229
oxide freon mixture.
They are then aerated and degassed for several days before use.
The caps are usually made of a harder resin than the bottles,
such as polystyrene, and are also gas sterilized and aerated
before use.
A special plastic ophthalmic packages are made of special
grade of polypropylene such that the entire package when filled
and sealed can be sterilized by autoclaving.
The glass dropper bottle is still used for products which are
extremely sensitive to oxygen or contain permeable
8/9/2019 Dosage Form I
150/229
components that are not sufficiently stable in plastic.
Powders for reconstitution also utilize glass containers due
to their heat transfer characteristics, which are necessary
during the freeze-drying process.
The glass should be type Ifor maximum compatibility with
the heat or steam autoclave sterilization. Amber glass is used
for light -sensitive drugs. A sterile dropper is made of glass or
LDPE plastic pipette and a rubber dropper bulb.
The pharmacist should instruct the patient on precautions to
prevent contamination during usage.
8/9/2019 Dosage Form I
151/229
8/9/2019 Dosage Form I
152/229
II. Soft contact lenses
8/9/2019 Dosage Form I
153/229
1. They are made of a hydrophilic transparent plastic
hydroxy-ethyl-methacrylate (HEMA), with small
amounts of cross-linking agents that provide a
hydrogel network.
2. They are 13 to 15 mm in diameter.
3. They cover the entire cornea.
Advantages:
1. They contain 30 - 80% water which enable enhanced
8/9/2019 Dosage Form I
154/229
permeability to oxygen and offer greater comfort to patient
than hard lenses.
2. Because of their size and coverage, they are less likely than
hard lenses to dislodge spontaneously.
3. They are less likely to permit irritating foreign particles (e.g.
dust or pollen) to lodge beneath them.
Disadvantages:
1. Do not provide the same high level of visual acuity as hardlenses.
2. Are less durable than hard lenses.
There are 2 types of soft contact lens:
1- Daily-wear lenses must be removed at night before the wearer
goes to Sleep
8/9/2019 Dosage Form I
155/229
goes to Sleep.
2- Extended-wearlenses are designed to be worn >24 hrs with
some approved for up to 30 days of continuous wear.
However, lenses should not be retained in eye > 4 - 7 days without
removal for cleaning & disinfection to avoid eye infection.
Disposable soft lenses do not require cleaning and disinfection for
the recommended period of use. They are discarded and replaced
with a new pair.
III- Rigid gas permeable (RGP) lenses
They are constructed of materials that are O permeable but
8/9/2019 Dosage Form I
156/229
They are constructed of materials that are O2 permeable but
hydrophobic.
There are 2 types of RGP contact lens:
A- daily-wear
B- Super permeable extended-wear.
Advantages
8/9/2019 Dosage Form I
157/229
They take advantages of both soft and hard lenses.
Compared to hard lenses, RGP lenses:
1. Permit greater movement of O2 through the lens.2. Retain the durability and ease of handling.
3. Provide greater wearing comfort.
Compared to soft lenses, RGP lenses:
8/9/2019 Dosage Form I
158/229
1. Provide strength, durability and longer life span",
and relatively easy care regimens.
2. Are easy to handle during insertion and removal.
3. Are more resistant to absorption of environmental
contaminants.4. Provide superior visual acuity.
Disadvantages
1. They require a greater adoption period for thewearer than soft lenses.
2. They are more easily dislodged in eye than soft
lenses.
Chapter IV
8/9/2019 Dosage Form I
159/229
AEROSOLS
8/9/2019 Dosage Form I
160/229
AEROSOLS
Definition:
8/9/2019 Dosage Form I
161/229
Colloidal systems, consisting of very finely subdividedliquid or solid particles dispersed in and surrounded by a
gas.
Aerosols have been used for the symptomatic treatmentof asthma as well as for the treatment of migraine.
Topical aerosols have been used to treat dermatological
manifestations.
Advantages:
1- Convenient and easy to use .
8/9/2019 Dosage Form I
162/229
2- There is no danger of contamination of the product withfore