DOORS - Titon Inc · 2020. 9. 1. · THREE-POINT LOCKS SERIES 8400 K11.13 01.04.2017 K11 DOORS Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 -...

THREE-POINT LOCKSSERIES 8400

K11.13

01.04.2017

K11

DOORS

Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - [email protected] - www.sobinco.com

CONTENTS

1. Three-point locks series 8400 ........................................... K11.13.031.1. General K11.13.031.2. Turning of the latch bolt and installation of the cylinder K11.13.04

2. Types .................................................................................... K11.13.052.1. Three-point lock with latch bolt and dead bolt K11.13.052.2. Three-point lock with narrow latch bolt and dead bolt K11.13.062.3. Three-point lock with roller and dead bolt K11.13.072.4. Three-point lock with dead bolt only K11.13.082.5. Three-point lock with short (K) or long (L) faceplate K11.13.09

3. Section preparations for lock ..............................................K11.13.10

4. Three-point locks series 8400E ..........................................K11.13.11

5. Three-pointlocksseries9400withSKGcertificate ......... K11.13.12

6. Keeps ................................................................................... K11.13.156.1. General K11.13.156.2. Keeps in zinc alloy K11.13.156.3. Adjustable keeps in stainless steel K11.13.176.4. Keeps in stainless steel K11.13.186.5. Keeps in stainless steel with plastic case K11.13.19

7. Section preparations for keeps .......................................... K11.13.20

8. Electric strikes .................................................................... K11.13.218.1. General information K11.13.218.2. Types and function K11.13.228.3. Electric strikes series 8355-.-. K11.13.23

9. Application examples .......................................................... K11.13.25

K11.13.02 MULTIPOINT LOCKS

THREE-POINT LOCKS SERIES 8400

K11.13

1. Three-point locks series 84001.1. General

• The 3 dead bolts are pivoting, rather than sliding. They are therefore longer than conventional bolts, so there is the same proportion of the dead bolt within the lockcase as is engaged into the frame, making it extremely difficult for burglars to force entry.

• The three-point lock has a special mechanism in the lockcase together with tapered top and bottom dead bolts which pull the vent section against the frame when locking the door, to provide an effective weather seal. Also a slightly deformed door (for example due to extreme weather conditions) can be closed without having to force the key.

• Faceplate (flat or U-form) in stainless steel.

• Very narrow lock: lockcase width = 15.5 mm.

• Locking and unlocking by a single turn of 360° with the cylinder key.

• The latch bolt can be operated by the door handle as well as by the key.

• Two holes above and below the handle opening allow the door handles to be screwed to each other through the lock, so there are no screws visible from the outside. In addition to a more pleasing look and increased security a much stronger fastening of the door handles is obtained.

• The lock can be used left hand and right hand simply by turning the latch bolt.

• The three-point lock is entirely made of non-corroding materials.

• Finish: - faceplate : stainless steel - lockcases : zinc alloy - latch bolt : zinc alloy nickel plated - dead bolts : zinc alloy nickel plated

• Vent height: - With short lock: 1825-2100 mm - With standard lock: 2100-2500 mm - With long lock: 2500-2900 mm

MULTIPOINT LOCKS K11.13.03


K11.13

• The locks are tested in accordance with the European standard EN 12209:2003/AC:2005 and obtained the following classification code:

1.2. Turning of the latch bolt and installation of the cylinder

Note: When a lock is mounted without cylinder, the plastic protection piece and screw should not be removed.

Turning of the latch bolt (A):

1. Put the dead bolt (B) in locked position.

2. Pull the latch bolt (A) forwards with a pair of pliers.

3. Turn the latch bolt (A) 180°.

4. Move the latch bolt (A) backwards.

Installation of the cylinder:Only for locks:

- n° ....-..-40 with flat faceplate - n° ....-U..-35 with U-faceplate - n° ....-U24-37 with U-faceplate

1. Install the cylinder.

2. Put the dead bolt (B) in locked position:

Case 1: the key can be removed from the cylinder.

Case 2: the key can not be removed from the cylinder.* unscrew the hexagon socket screw (1).* turn the key to put the catch (2) in the lower position.* tighten screw (1).

Categoryof use

Durability Door massFire

resistanceSafety

Corrosionresistance

SecurityDoor

applicationType of keyoperation

Type ofspindle

Keyidentification

3 X 7 0 0 C 2 B A 2 0



K11.13

2. Types2.1. Three-point lock with latch bolt and

dead bolt

Order code A (mm) B (mm) C (mm) E (mm)8401-16-30 27 30 16 9.58405-16-30 13.58401-16-35 32 35 16 9.58405-16-35 13.58401-16-40 37 40 16 9.58405-16-40 13.58401-20-30 27 30 20 9.58405-20-30 13.58401-20-35 32 35 20 9.58405-20-35 13.58401-20-40 37 40 20 9.58405-20-40 13.58401-24-30 27 30 24 9.58405-24-30 13.58401-24-35 32 35 24 9.58405-24-35 13.58401-24-40 37 40 24 9.58405-24-40 13.5

Flat faceplate

Order code A (mm) B (mm) C (mm) D (mm) E (mm)8401-U22-25 22.5 29 22 6.5 10.58405-U22-25 14.58401-U22-30 27.5 34 22 6.5 10.58405-U22-30 14.58401-U22-35 32.5 39 22 6.5 10.58405-U22-35 14.58401-U24-25 22.5 29 24 6.5 10.58405-U24-25 14.58401-U24-27 24 29 24 5 10.58405-U24-27 14.58401-U24-30 27.5 34 24 6.5 10.58405-U24-30 14.58401-U24-32 29 34 24 5 10.58405-U24-32 14.58401-U24-35 32.5 39 24 6.5 10.58405-U24-35 14.58401-U24-37 34 39 24 5 10.58405-U24-37 14.5

U-faceplate



K11.13

2.2. Three-point lock with narrow latch bolt and dead bolt

Flat faceplate

U-faceplate

Order code A (mm) B (mm) C (mm) E (mm)8401B-16-30 27 30 16 9.58405B-16-30 13.58401B-16-35 32 35 16 9.58405B-16-35 13.58401B-16-40 37 40 16 9.58405B-16-40 13.58401B-20-30 27 30 20 9.58405B-20-30 13.58401B-20-35 32 35 20 9.58405B-20-35 13.58401B-20-40 37 40 20 9.58405B-20-40 13.58401B-24-30 27 30 24 9.58405B-24-30 13.58401B-24-35 32 35 24 9.58405B-24-35 13.58401B-24-40 37 40 24 9.58405B-24-40 13.5

Order code A (mm) B (mm) C (mm) D (mm) E (mm)8401B-U22-25 22.5 29 22 6.5 10.58405B-U22-25 14.58401B-U22-30 27.5 34 22 6.5 10.58405B-U22-30 14.58401B-U22-35 32.5 39 22 6.5 10.58405B-U22-35 14.58401B-U24-25 22.5 29 24 6.5 10.58405B-U24-25 14.58401B-U24-27 24 29 24 5 10.58405B-U24-27 14.58401B-U24-30 27.5 34 24 6.5 10.58405B-U24-30 14.58401B-U24-32 29 34 24 5 10.58405B-U24-32 14.58401B-U24-35 32.5 39 24 6.5 10.58405B-U24-35 14.58401B-U24-37 34 39 24 5 10.58405B-U24-37 14.5



K11.13

2.3. Three-point lock with roller and dead bolt

• The roller has an adjustment range of 8 mm. Adjust the roller with a hexagonal spanner of 2.5 mm.

Flat faceplate

U-faceplate

Order code A (mm) B (mm) C (mm)8411-16-30 27 30

168411-16-35 32 358411-16-40 37 408411-20-30 27 30

208411-20-35 32 358411-20-40 37 408411-24-30 27 30

248411-24-35 32 358411-24-40 37 40

Order code A (mm) B (mm) C (mm) D (mm)8411-U22-25 22.5 29

226.5

8411-U22-30 27.5 34 6.58411-U22-35 32.5 39 6.58411-U24-25 22.5 29

24

6.58411-U24-27 24 29 58411-U24-30 27.5 34 6.58411-U24-32 29 34 58411-U24-35 32.5 39 6.58411-U24-37 34 39 5

Adjustable roller



K11.13

2.4. Three-point lock with dead bolt only

Flat faceplate

U-faceplate

Order code A (mm) B (mm) C (mm)8421-16-30 27 30

168421-16-35 32 358421-16-40 37 408421-20-30 27 30

208421-20-35 32 358421-20-40 37 408421-24-30 27 30

248421-24-35 32 358421-24-40 37 40

Order code A (mm) B (mm) C (mm) D (mm)8421-U22-25 22.5 29

226.5

8421-U22-30 27.5 34 6.58421-U22-35 32.5 39 6.58421-U24-25 22.5 29

24

6.58421-U24-27 24 29 58421-U24-30 27.5 34 6.58421-U24-32 29 34 58421-U24-35 32.5 39 6.58421-U24-37 34 39 5



K11.13

2.5. Three-point lock with short (K) or long (L) faceplate• All locks are also available as shorter or longer

version: the distance between main lock and top lock is smaller or bigger as for the standard type.

84..K-..-.. 84..K-U..-.. 84..L-..-.. 84..L-U..-..Faceplate 6.5 mm Faceplate 5 mm



K11.13

3. Section preparations for lockFlat faceplate U-shaped faceplateU-shaped faceplate

Hole ø14 mm is not required for locks with roller or locks without latch bolt.

R = Height reference.

Lock A(mm)B

(mm)C

(mm)D

(mm)84..-..-.. 250 250 571 17984..K-..-.. 225 0 296 17984..K-U..-.. 225 0 296 17984..L-..-.. 450 250 771 17984..L-U..-.. 450 250 771 0



K11.13

4. Three-point locks series 8400E

• Type E = with deactivating mechanism:

- All locks with latch bolt series 8400 can be provided with this mechanism to deactivate the latch bolt. - The latch bolt is deactivated by pushing it into the lockcase and by turning the small cover.

• Locks:

With flat faceplate

With U-faceplate

deactivation latch bolt

Order code A (mm) B (mm) C (mm) E (mm)8401E-20-30 27 30 20 9.58405E-20-30 13.58401E-20-35 32 35 20 9.58405E-20-35 13.58401E-20-40 37 40 20 9.58405E-20-40 13.58401E-24-30 27 30 24 9.58405E-24-30 13.58401E-24-35 32 35 24 9.58405E-24-35 13.58401E-24-40 37 40 24 9.58405E-24-40 13.5

Order code A (mm) B (mm) C (mm) D (mm) E (mm)8401E-U22-25 22.5 29 22 6.5 10.58405E-U22-25 14.58401E-U22-30 27.5 34 22 6.5 10.58405E-U22-30 14.58401E-U22-35 32.5 39 22 6.5 10.58405E-U22-35 14.58401E-U24-25 22.5 29 24 6.5 10.58405E-U24-25 14.58401E-U24-27 24 29 24 5 10.58405E-U24-27 14.58401E-U24-30 27.5 34 24 6.5 10.58405E-U24-30 14.58401E-U24-32 29 34 24 5 10.58405E-U24-32 14.58401E-U24-35 32.5 39 24 6.5 10.58405E-U24-35 14.58401E-U24-37 34 39 24 5 10.58405E-U24-37 14.5



K11.13

5. Three-point locks series 9400 with SKG certificateGeneral information

• The Foundation for Quality of window and door systems (SKG) is a recognised and independent test institution. The Foundation tests and awards certificates for windows, doors, facades and fittings. SKG awards stars to specify the quality of high security fittings and complete windows and doors. There are 3 categories to distinguish the different classes of security. - Standard: 1 star - Heavy: 2 stars - Extra heavy: 3 stars

• The conditions to obtain this product certificate are described in the SKG Regulations. The tests are done in accordance with NEN 5089 “Safety against burglary of buildings: high security fittings”.

• The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG.

• Three-point locks series 9400 look the same and are mounted in the same way as three-point locks series 8400, but offer a higher security against forced entry.

• The dead bolt of the main lock is equipped with two invisible cemented carbide rollers and the upper and lower dead bolt are both equipped with two visible bars in hard metal. This makes it impossible to cut the 3 bolts with a hacksaw. Recommended for double action doors and doors without rebate.

• These high security locks are especially adapted and reinforced to comply with the rigorous SKG standards for security against forced entry.

• The two fixing holes, above and below the handle follower are suitable for screws M6.

• All other dimensions of the SKG type are the same as for the standard type.



K11.13

Withflatfaceplate

SKG-type Standard typeOrder code Category Certificate number Order code Page

8401P-16-30 - - 8401-16-30 K11.13.058405P-16-30 - - 8405-16-30 K11.13.058411P-16-30 - - 8411-16-30 K11.13.078421P-16-30 - - 8421-16-30 K11.13.08

8401P-16-35 - - 8401-16-35 K11.13.058405P-16-35 - - 8405-16-35 K11.13.058411P-16-35 - - 8411-16-35 K11.13.078421P-16-35 - - 8421-16-35 K11.13.08

8401P-16-40 - - 8401-16-40 K11.13.058405P-16-40 - - 8405-16-40 K11.13.058411P-16-40 - - 8411-16-40 K11.13.078421P-16-40 - - 8421-16-40 K11.13.08

9401-20-30 417.211.01 8401-20-30 K11.13.05

9405-20-30 417.211.01 8405-20-30 K11.13.05

9411-20-30 417.211.01 8411-20-30 K11.13.07

9421-20-30 417.211.01 8421-20-30 K11.13.08

9401-20-35 417.211.01 8401-20-35 K11.13.05

9405-20-35 417.211.01 8405-20-35 K11.13.05

9411-20-35 417.211.01 8411-20-35 K11.13.07

9421-20-35 417.211.01 8421-20-35 K11.13.08

9401-20-40 417.211.01 8401-20-40 K11.13.05

9405-20-40 417.211.01 8405-20-40 K11.13.05

9411-20-40 417.211.01 8411-20-40 K11.13.07

9421-20-40 417.211.01 8421-20-40 K11.13.08

9401-24-30 417.211.01 8401-24-30 K11.13.05

9405-24-30 417.211.01 8405-24-30 K11.13.05

9411-24-30 417.211.01 8411-24-30 K11.13.07

9421-24-30 417.211.01 8421-24-30 K11.13.08

9401-24-35 417.211.01 8401-24-35 K11.13.05

9405-24-35 417.211.01 8405-24-35 K11.13.05

9411-24-35 417.211.01 8411-24-35 K11.13.07

9421-24-35 417.211.01 8421-24-35 K11.13.08

9401-24-40 417.211.01 8401-24-40 K11.13.05

9405-24-40 417.211.01 8405-24-40 K11.13.05

9411-24-40 417.211.01 8411-24-40 K11.13.07

9421-24-40 417.211.01 8421-24-40 K11.13.08



K11.13

With U-faceplate

SKG-type Standard typeOrder code Category Certificate number Order code Page

9401-U22-25 417.211.01 8401-U22-25 K11.13.05

9405-U22-25 417.211.01 8405-U22-25 K11.13.05

9411-U22-25 417.211.01 8411-U22-25 K11.13.07

9421-U22-25 417.211.01 8421-U22-25 K11.13.08

9401-U22-30 417.211.01 8401-U22-30 K11.13.05

9405-U22-30 417.211.01 8405-U22-30 K11.13.05

9411-U22-30 417.211.01 8411-U22-30 K11.13.07

9421-U22-30 417.211.01 8421-U22-30 K11.13.08

9401-U22-35 417.211.01 8401-U22-35 K11.13.05

9405-U22-35 417.211.01 8405-U22-35 K11.13.05

9411-U22-35 417.211.01 8411-U22-35 K11.13.07

9421-U22-35 417.211.01 8421-U22-35 K11.13.08

9401-U24-25 417.212.01 8401-U24-25 K11.13.05

9405-U24-25 417.212.01 8405-U24-25 K11.13.05

9411-U24-25 417.212.01 8411-U24-25 K11.13.07

9421-U24-25 417.212.01 8421-U24-25 K11.13.08

9401-U24-30 417.212.01 8401-U24-30 K11.13.05

9405-U24-30 417.212.01 8405-U24-30 K11.13.05

9411-U24-30 417.212.01 8411-U24-30 K11.13.07

9421-U24-30 417.212.01 8421-U24-30 K11.13.08

9401-U24-35 417.212.01 8401-U24-35 K11.13.05

9405-U24-35 417.212.01 8405-U24-35 K11.13.05

9411-U24-35 417.212.01 8411-U24-35 K11.13.07

9421-U24-35 417.212.01 8421-U24-35 K11.13.08

9401-U24-27 417.211.01 8401-U24-27 K11.13.05

9405-U24-27 417.211.01 8405-U24-27 K11.13.05

9411-U24-27 417.211.01 8411-U24-27 K11.13.07

9421-U24-27 417.211.01 8421-U24-27

9401-U24-32 417.211.01 8401-U24-32 K11.13.05

9405-U24-32 417.211.01 8405-U24-32 K11.13.05

9411-U24-32 417.211.01 8411-U24-32 K11.13.07

9421-U24-32 417.211.01 8421-U24-32 K11.13.08

9401-U24-37 417.211.01 8401-U24-37 K11.13.05

9405-U24-37 417.211.01 8405-U24-37 K11.13.05

9411-U24-37 417.211.01 8411-U24-37 K11.13.07

9421-U24-37 417.211.01 8421-U24-37 K11.13.08



K11.13

6. Keeps6.1. General

• There are 3 types of keeps: - keeps in zinc alloy with case for use with dead bolts. - keeps in stainless steel without case for use with dead bolts. - keeps in stainless steel with plastic case for use with dead bolts.

• The keeps are suitable for locks with latch bolt and dead bolt, with roller and dead bolt, or with dead bolt only.

• The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG.

6.2. Keeps in zinc alloy• The keeps are horizontally adjustable by means of

serrated plates. The adjustment range is 3 mm.• The keeps are encased which gives a neat appearance

and keeps the frame section free from dirt.• Finish: keeps in zinc alloy, coated natural colour.

Fixing by means of serrated plates with a horizontal adjustment range of 3 mm.

Middle keep

Order code G(mm)H

(mm)I

(mm)8351-1 5.5 0 188351-2 14.5 0 188351-3 11 0 188351-4 8.5 0 188351-5 5.5 5 188351-7 5.5 0 23

Top and bottom keep

Order code G(mm)H

(mm)I

(mm)8352-1 5.5 0 188352-2 14.5 0 188352-3 11 0 188352-4 8.5 0 188352-5 5.5 5 188352-7 5.5 0 23



K11.13

n° 8352-10

n° 8351-10



K11.13

6.3. Adjustable keeps in stainless steel• Extra slim keeps for sections with minimal installation depth.

• The keeps are horizontally adjustable by means of 2 eccentric rollers. The adjustment range is 3 mm.

• Finish: stainless steel.

n° 8358-2

allen key s4

allen key s4

n° 8357-2

allen key s4

allen key s4



K11.13

6.4. Keeps in stainless steel• Extra slim keeps for sections with minimal installation depth.• Finish: keeps in stainless steel.

• Fixing holes with a horizontal adjustment range of 3 mm.

• Keeps n° 8353-7C and n° 8354-7C are not horizontally adjustable.

Top and bottom keep

Order code G(mm)H

(mm)I

(mm)J

(mm)8354-1 2.5 0 20 108354-3 3 0 24 128354-5 3 0 20 98354-7 3 0 24 98354-7B 3 5 24 98354-7C 3 5 24 9

Middle keep

Order code G(mm)H

(mm)I

(mm)J

(mm)8353-1 2.5 0 20 108353-3 3 0 24 128353-5 3 0 20 98353-7 3 0 24 98353-7B 3 5 24 98353-7C 3 5 24 9



K11.13

6.5. Keeps in stainless steel with plastic case• Extra slim keeps for sections with minimal installation depth.• Finish:

- keeps in stainless steel - case in black plastic

• Fixing holes with a horizontal adjustment range of 3 mm.

• Keeps n° 8353-8C and n° 8354-8C are not horizontally adjustable.

Top and bottom keep

Order codes G(mm)H

(mm)I

(mm)J

(mm)8354-2 2.5 0 20 108354-4 3 0 24 128354-6 3 0 20 98354-8 3 0 24 98354-8B 3 5 24 98354-8C 3 5 24 9

Middle keep

Order code G(mm)H

(mm)I

(mm)J

(mm)8353-2 2.5 0 20 108353-4 3 0 24 128353-6 3 0 20 98353-8 3 0 24 98353-8B 3 5 24 98353-8C 3 5 24 9



K11.13

7. Section preparations for keepsProfilewithframegroove Profilewithoutframegroove

R = Height reference.

KEEP DETAILadjustable

adjustable

adjustable

KEEP DETAILadjustable

adjustable

adjustable

Zinc alloy keeps 8351-... and 8352-... (top/bottom)

With lock F(mm)G

(mm)Z

(mm)84..-..-.. 637 718

6084..K-..-.. 362 44384..K-U..-.. 362 44384..L-..-.. 837 91884..L-U..-.. 837 918

Stainless steel keeps 8353-... and 8354-... (top/bottom)

With lock F(mm)G

(mm)Z

(mm)84..-..-.. 612 718

8584..K-..-.. 337 44384..K-U..-.. 337 44384..L-..-.. 812 91884..L-U..-.. 812 918



K11.13

8. Electric strikes8.1. General information

• Small electric strike incorporating a space-saving locking flap, especially developed for installation in aluminium doors.

• The flap rotates back within the keep when operated. Big advantage: the cut-out is much smaller making the installation aesthetically pleasing.

• Break-in resistance of strike: 3750 N.

• Width adjustment of the locking flap: 3 mm.

• Current consumption: - Alternating current (AC): 250 mA at 12V - Direct current (DC): 280 mA at 12V

• The electric strikes are handed.

Mechanical Reset button Electricalrelease connection

(versionE)

• Quick and easy electrical connection.

• The reset button applies only to type 128 where the strike is held in the release position until the door has been opened.

• This button resets the electric strike when the door opens.

• The release button (version E) allows to suspend temporarily the automatic locking upon closing the door.

• Only available for type 118 and 128.

Reset button

Electrical connection

Release button

Adjustment range



K11.13

8.2. Types and function

Model 118• The door is only unlocked when you push a

button. After releasing the button the door is locked again.

• This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V.

• Note: when the door is pushed open by the gaskets, the door can still be open after releasing the button. This can be solved by mounting a door closer on the door.

• This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door.

Model 128• On releasing the electric strike, for example, from a button on an intercom system, the strike is held in

the release position until the door has been opened.

• The electric strike resets when the door opens. This means there is no need to rush through the door.

• This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V.

• This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door.

Model 138

• This type works on 12V DC or 24V DC and may be permanently connected to electrical current.

• The electric strike is mainly used in combination with an emergency or a fire centre. In case of a power failure, the door can be opened.

Electric strike

Door

Operation

Electric strike

Door

Operation

Electric strike

Door

Operation



K11.13

8.3. Electric strikes series 8355-.-.• Electric strikes with extended faceplate for latch bolt and dead bolt.

• Finish: keep in aluminium natural anodised.

left hand = illustratedright hand = opposite view

• Order example: 8355-6-128E leftThis is an electric strike with release button (E) with faceplate height of 15 mm and an electric strike type 128 (see page K11.13.22) working on 10-24V AC/DC.

Movement of locking flap

3 mm adjustmentOrder code

A (mm)

B (mm)

C (mm)

8355-1 5 11.5 6.5

8355-2 8 8 3

8355-3 10 8 3

8355-4 12 8 3

8355-5 8 11.5 6.5

8355-6 15 8 3

8355-8 10 11.5 6.5

Possibilities

118 10-24V AC/DC

left or

right

118E 10-24V AC/DC

128 10-24V AC/DC

128E 10-24V AC/DC

138-12 12V DC

138-24 24V DC



K11.13

• Order example: 8355-9-128E leftThis is an electric strike with release button (E) and with an electric strike type 128 (see page K11.13.22) working on 10-24V AC/DC.

Order code Possibilities

8355-9

118 10-24V AC/DC

left or

right

118E 10-24V AC/DC

128 10-24V AC/DC

128E 10-24V AC/DC

138-12 12V DC

138-24 24V DC

Movement of locking flap

3 mm adjustment



K11.13

9. Application examples

Bottom lock of three-point lock n° 8401-U22-30+ keep n° 8352-3

Three-point lock n° 8401-20-35+ keep n° 8351-5

Three-point lock n° 8411-U22-35 Three-point lock n° 8401B-20-35+ keep n° 8351-5 + electric strike n° 8355-1-. right



K11.13

DOORS - Titon Inc · 2020. 9. 1. · THREE-POINT LOCKS SERIES 8400 K11.13 01.04.2017 K11 DOORS Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 -...

Documents