This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data
Factory-applied Colorstyle finish is a two-part, urethane top-coat that is electrostatically applied over the standard primer. The paint is then oven cured.
The chemically reactive cure provides a top quality, abrasion resistant finish with excellent weathering characteristics. This finish is environmentally friendly in that it does not contain heavy metal pigments.
60˚ Gardner Gloss: 15 to 20.Colors: Standard color selectors available upon request.
Performance Data
Colorstyle, factory applied finish paint process has been subjected to the following tests: Salt Spray Humidity Accelerated Weathering Impact Film Adhesion Abrasion
Factory applied Colorstyle finish paint meets the performance requirements and acceptance criteria as stated in ANSI Standard A250.3, “Test Procedure and Acceptance Criteria for Factory Applied Finish Painted Steel Surfaces...”.
11-003
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data
NOMINAL SIZES
NOMINAL DOOROPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
NOMINAL DOOR OPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
SINGLE FRAME
FLOORFINISH
DOUBLE FRAME
WIDTH WIDTH
2-8
2-10
3-0
2-4
2-6
2-0
5-4
6-0
5-8
4-8
5-0
4-0
OPENING HEIGHT
SINGLE PAIR
6-8 7-0 7-2
STANDARD DOOR OPENING SIZES
FRAMES ON THIS PAGE ARE FOR USE WITH 1-3/8" THICK DOORS.
1-3/8” DOOR FRAME
11-101
7-2 7-0 6-8 6-8
7-2 7-0 6-8
10.37"
9.75"
10.37"
9.75"
LC
STRIKEHEIGHT
STRIKEHEIGHT
*
LC
LC
LC
LC
LC
LC
LC
LC
32.9
3"32
.93"
31.9
3"
29.9
3"
31.9
3"
29.9
3"
59.8
7"
26.1
8"
24.1
8"
20.1
8"
19.5
"20
.18" 33.62"
40.31"
HIN
GE
SPA
CIN
G
HIN
GE
SPA
CIN
G
1640( )5"
810( )3"
9( )3"4
32 ()
1615"
15"
16(31
)
15"
16(29
)
15"
16(32
)
15"
16(31
)
15"
16(29
)
59 (7")
8
( 4 )3"9
26 (3" 16)
24 (16
)3"
20 (16
)3"
19 (1")
2(20
163")
10( )83"
( )833 5"
DUTCH DOOR FRAME
STANDARD FRAME
FRAME HEIGHTS
FRAME HEIGHTS
Labeled 6-8 frames require3 hinges.
2 hinges standard for non-labeled6-8 frames
3 hinges optional for non-labeled 6-8 frames
*
11-102
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/8” DOOR FRAMES HINGE AND STRIKE LOCATIONS
NOMINAL SIZES
1-3/4” DOOR FRAME SIZES
11-103
FLOORFINISH
NOMINAL DOOROPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
NOMINAL DOOR OPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
SINGLE FRAME DOUBLE FRAME
8-0
3-10
4-0
3-8
8-0
7-8
7-4
WIDTH WIDTH
2-8
2-10
3-6
3-4
3-0
2-4
2-6
2-0
5-4
7-0
6-8
6-0
5-8
4-8
5-0
4-0
OPENING HEIGHT
SINGLE PAIR
6-8 7-0 7-107-2 10-09-0
5-0 10-0
STANDARD DOOR OPENING SIZES
These hardware locations are Ceco Door Productsstandard and will be furnished unless
otherwise agreed to.
STANDARD HARDWARE LOCATIONS 1-3/4"DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS
4-1/2" OR 5" HIGH HINGES
11-104 12/1/04
9"
9"
DOOR OPENING HEIGHTS
6-87-07-2
34"
34"
33"
33"
31"
31"
STRIKEHEIGHT
CL
CL
CL
CL
41.81"
HIN
GE
SPA
CIN
G
13"1641( )
11-104
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS4-1/2” OR 5” HIGH HINGES
These hardware locations are Ceco Door Productsstandard and will be furnished unless
otherwise agreed to.
approximation to .33".21/64" represents a measurable*
NOMINAL SIZES
STANDARD HARDWARE LOCATIONS FOR1-3/4” DOOR FRAMES:7-10, 8-0, 9-0, AND 10-0 HEIGHTS
11-104A
26"
34"
34"
26"
25.3
3"
26"
34"
41.81"
STRIKEHEIGHT
9"
9"
7-108-010-0
DOOR OPENING HEIGHTS
9-0
30"
30"
30"
CL
CL
CL
CL
CL
HIN
GE
SPA
CIN
G
13"1641( )
21"
64(25
)*
64(
)25
.33"
2521
"*
64(
)25
.33"
2521
"*
NOMINAL SIZES
FACTORY STANDARD HARDWARELOCATIONS: HEIGHTS 5’-0” THRU 10’-0”
11-104C
5'-1" 3 2 @ 21.5"
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
5'-2" 2 @ 22"
5'-3" 2 @ 22.5"
5'-4" 2 @ 23"
5'-5" 2 @ 23.5"
5'-6" 2 @ 24"
5'-7" 2 @ 24.5"
5'-8" 2 @ 25"
5'-9" 2 @ 25.5"
5'-10" 2 @ 26"
5'-11" 2 @ 26.5"
6'-0" 2 @ 27"
6'-1" 2 @ 27.5"
6'-2" 2 @ 28"
6'-3" 2 @ 28.5"
6'-4" 2 @ 29"
6'-5" 2 @ 29.5"
6'-6" 2 @ 30"
6'-7" 2 @ 30.5"
6'-8" 2 @ 31"
6'-9" 2 @ 31.5"
6'-10" 2 @ 32"
6'-11" 2 @ 32.5"
7'-0" 2 @ 33"
7'-1" 2 @ 33.5"
7'-2" 2 @ 34"
7'-3" 2 @ 34.5"
7'-4" 2 @ 35"
7'-5" 2 @ 35.5"
7'-6" 2 @ 36"
9'-9"
10'-0"
9'-11"
9'-10"
9'-2"
9'-8"
9'-7"
9'-6"
9'-5"
9'-4"
9'-3"
9'-1"
9'-0"
8'-11"
8'-10"
8'-9"
8'-8"
8'-1"
8'-7"
8'-6"
8'-5"
8'-4"
8'-3"
8'-2"
8'-0"
7'-11"
7'-10"
7'-9"
7'-8"
7'-7" 4 3 @ 24.33"4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3 @ 24.66"
3 @ 25"
3 @ 25.33"
3 @ 25.66"
3 @ 26"
3 @ 26.33"
3 @ 26.66"
3 @ 27"
3 @ 27.33"
3 @ 27.66"
3 @ 28"
3 @ 28.33"
3 @ 28.66"
3 @ 29"
3 @ 29.33"
3 @ 29.66"
3 @ 30"
3 @ 30.33"
3 @ 30.66"
3 @ 31"
3 @ 31.33"
3 @ 31.66"
3 @ 32"
3 @ 32.33"
3 @ 32.66"
3 @ 33"
3 @ 33.33"
3 @ 33.66"
3 @ 34"
5'-0" 2 42"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
LC
9"
DOOR OPENING HEIGHTS
7-2 7-0 6-8
HEIGHTSTRIKE
8-0
33.62"
9"
CL
LC
LC
LC
38.3
1"
28.3
1"
26.3
1"
22.3
1"
17.3
7"H
ING
E SP
AC
ING
16(
5"38
)
5"(
)16
28
5"(
)16
26
5"(
)16
22
22.3
1"(
16)
225"
17 (3")
8
33( 5")8
otherwise agreed to.standard and will be furnished unless
These hardware locations are Ceco Door Products
11-104D
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS, 1-3/4”DUTCH FRAMES: 6-8, 7-0, 7-2 & 8-0HEIGHTS - 4-1/2” OR 5” HIGH HINGES
HARDWARE LOCATIONS SHOWN BELOW ARE BASEDON THE FOLLOWING:
5" from head to top of upper hinge.10" from bottom of jamb to bottom of lower
Equal spacing between intermediate hinges.
The above hardware locations will befurnished only when agreed to.
Strike Height On Frame IsDependent On Knob OrCrossbar Height. Refer ToDoor Hardware Locations(p. 01-403) And Manufacturer'sLock Template To DetermineRelationship Between Lock And Strike.
HINGE REINFORCEMENT ANDPLASTER GUARD APPLIEDPER PAGE #11-202
STEEL STRAP
11-208
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDOOR FRAME HIGH FREQUENCYHINGE REINFORCEMENT STRAP
NOMINAL SIZES
DOOR FRAME MUTES
11-209
9 3/4" MAX.
C OF
STRIKEL
M M
6" ON CENTERM
12" MAX.
12" MAX.
M
M
INSERT BLUNT END OF 3/32" DIAMETER WIREOR TOOL IN HOLE IN CENTER OF MUTE.
MOISTEN CONE PORTION AND INSERT IN HOLE INSTOP OF FRAME, PUSHING SLOWLY WITH CIRCULARMOTION TO ELONGATE MUTE SUFFICIENTLY TOSET IN PLACE.
REMOVE WIRE
1.
2.
3.
DOOR MUTES (SILENCERS) MAINTAIN PROPERSPACE (1/16") BETWEEN DOOR AND FRAMESTOP AND CUSHION DOOR CLOSING. INSERTMUTES INTO FRAME BEFORE FRAME IS INSTALLED INTO WALL TO PREVENT GROUT,PLASTER, ETC. FROM FILLING HOLES.
SINGLE SWING DOUBLE SWING
STANDARD LOCATION OF DOOR MUTES
SINGLE SWING DOOR FRAMES - 3 MUTES DOUBLE SWING DOOR FRAMES - 2 MUTES DUTCH DOOR FRAMES - 4 MUTES
M = MUTE
Fed. Spec. Type 1337A
Note 1Pips are provided forprojection welding. Ifother welding is used,flip Part A over.
A. (12 ga. galv. steel)
B. (16 ga. galv. steel, prime paint)
D. #8-32 x 1/2" UCFHMS (2)
STRIKE FILLER
STRIKE
REINFORCEMENT
PLASTER GUARD
Part B
Tackweld Part E on back ofreinforcement as necessary.
Note 1
RRA/LA shownFlip flop Part Bfor LRA/RA
Center of cutoutand door
Center line of Door Opening Widthand Cutout
HEAD
Part C
Part B
Part A
Tapped for#8-32 MS
Weld Part Ato Head at each side
Part A
Part D
E. Plaster guard (Included on SU and SQ frames only)
WELDING TYPE T-1 "STITCH WELD at SOFFIT ONLY"Standard KD frame components from stock with corner reinforcements.NO SAWING REQUIRED.
WELDING TYPET-1
(1-1/2" wide and up)
jamb soffit seam.end of the head andwelds located at eachTwo 1/2" long stitch
located in the centerlength stitch weld,One 1/2" (minimum)
WIDE STOP
Wide Stop:
(up to 1-1/2" wide)NARROW STOP
of the soffit.
Narrow Stop
Reference: This corner has a full and continuousbackbend at the head and jambs. It can be usedon frames that cap the wall.
FACE-MITER SEAMIS VISIBLE
STANDARD KD JAMB
STANDARD KD HEAD
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight". Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs towards outside (toward jamb backbends).
2. Place weld bead as required at the joint of the head and jamb soffits from the backside.
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.WELDING TYPE T-2 "OUTSIDE FACE WELD ONLY"
Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.
3. Grind an dress smooth bothface-miter seams after welding.
Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.
WELDING TYPE T-2 "OUTSIDE FACE WELD and FULL WEB WELD"
4. Weld the entire web seam(including the seams betweenhead and jamb rabbets, stopsand soffits) from the backside,
4a. If weld penetration occurs, file smooth.
5. Spot paint
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight" Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs toward outside(toward jamb backbends) of
2. Weld the entire face-miter seam, between head and jamb, from the outside (both faces).
3. Grind and dress smooth both face-miter seams after welding.
3a. Spot paint
frame.
2
STANDARD KDHEAD
STANDARD KDJAMB
FACE-MITER SEAMIS COMPLETELYINVISBLE
T-3
toward outside(toward jamb backbends) of (toward throat) of frame. Bend rabbet tabs Bend corner reinforcement tabs toward inside that face-miter seam is "closed" and "tight"1. Assemble frame: Bend tabs after assuring
WELDING TYPE V-3 "INSIDE FACE WELD and FULL WEB WELD"
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and tight. Bend rabbet tabs toward outside (toward jamb backbends) of frame.
2. Weld the entire face-miter seam from the inside. Weld is to penetrate to exterior.
2a. Grind the exterior face and fill as necessary.
3. Dress reworked areas.
4. Weld the entire web seam (including the seams between head and jamb rabbets, stops, and soffits) from the backside with a continuous weld bead.
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)
Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.
AND BUTT AGAINST INSIDEINSIDE OF DOOR SOFFITPLACE FLAT AGAINST
DOORRABBET
OF DOOR STOP
Note: Verify against manufacturer's templatethat size and position of plate satisfyhardware needs.hardware needs.
that size and position of plate satisfyNote: Verify against manufacturer's template
INSIDE OF DOOR FACE
RABBETDOOR
PLACE FLAT AGAINST IN-SIDE OF RABBET OPPOSITEDOOR AND BUTT AGAINST
11-401PLATE, SEEOPTIONALLOCATION OF
to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big
14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:
CLOSER MOUNTINGPARALLEL ARM
JAMBHINGE
(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE
hardware needs.that size and position of plate satisfyNote: Verify against manufacturer's template
OF DOOR RABBET
RABBETDOOR
PLACE FLAT AGAINSTINSIDE OF FACE ANDBUTT AGAINST INSIDE
to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big
14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:
INSWING DOOR: SURFACE BOLTS
(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE
JAMBBOTTOM OF STRIKE
RABBETDOOR
END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX)
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)
Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.
PLACE FLAT AGAINSTINSIDE OF DOOR SOFFITAND BUTT AGAINST INSIDEOF DOOR STOP
RIM TYPE PANICDEVICE MOUNTING
14"
14"2" 7"
33-5/16"
40-5/16"
14"
7"
cL
HEADHEAD
CL of opening
L of openingC
HEAD
7"
14"
11-402
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCLOSER REINFORCEMENTPLATE TYPE
SECTIONFRAME HEAD
1-15/16"RABBET
DOORSIDE
HEAD
CR/HALF
SPOT OR TACKWELDED IN PLACE.
(2) WELDS PER END
REGULAR & PARALLELARM CLOSER MOUNTING
14GA. GALV. STL.
NOMINAL SIZES
HALF-CLOSER REINFORCEMENT
11-403
1-5/8"
5/8"
1-1/2"
1-31/32"
13-7/8"
2" MIN.FACE
4" 13-7/8"
HINGEJAMB
NOMINAL SIZES
JAMB ANCHOR QUANTITIESFOR STANDARD HEIGHT FRAMES
11-500
* Floor anchors may be omitted and replaced with two additional jamb anchors.
Unless otherwise indicated, jamb anchors are normally located on the same center line as the hinge preparations except where interference would occur with hardware reinforcements. Where interference would occur, anchors should be positioned above or below hinge reinforcements and directly opposite on the strike jamb.
For sizes other than listed above, the following guidelines are followed (unless otherwise indicated)...For heights to 6-0: Two jamb anchors per jamb; For heights greater than 6-0 thru 7-6: Three jamb anchors per jamb; For heights greater than 7-6 thru 10-0: Four jamb anchors per jamb; and for each additional 2 feet of height or fraction thereof: One additional jamb anchor per jamb.
ANCHOR TYPE
NEW MASONRY 6 8
8 10 OMIT
2
2 *
6 8 2WOOD STUD
METAL STUD
SOLID PLASTER
LAMINATEDDRYWALL
EXISTING OPENING
QUANTITY
6-8 THRU 7-2 7-10 THRU 10-0
FLOOR ANCHORSPER FRAME
JAMB ANCHORS PER FRAME
*
6 8
2 *6 8
2 *6 8
NOMINAL SIZES
WELDED FLOOR ANCHOR
11-501
3-1/8
1-23/32
1-7/16
1/2
1/21/2
5/16 DIA.HOLES
1-1/2
1-1/2
1/2
DIM A
1" CTCSPACES
5/16 DIA.HOLES
11/16 11/16
DIM A FRAME DEPTH HOLES
3-1/25
6-1/28
4-1/2 to 5-1/45-3/8 to 6-3/46-7/8 to 8-1/48-3/4 to 9-3/4
3568
ONE PIECE ANCHOR SELECTION CHART
All dimensions are in inches. For SI conversion: 1" = 25.4 mm.Anchors for depths outside the above range are made to order.
TWO PIECE ANCHOR
(16 GA. GALV.)(16 GA. COLD ROLLED)
CENTER OF JAMBAND ANCHOR
16 GAGEGALV STEEL
WELDWELD
TWO PIECE APPLICATION ONE PIECE APPLICATION
11-502
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataADJUSTABLE FLOOR ANCHOR
4" TRAVEL
2-1/8"
5/16" DIA.2-1/8"
O.A.
HAT:4-1/4" WIDE x 3/4" LEGSx 5/8" OFFSET @ 3-1/4"LONG
ANGLE:1-1/2" x 6-3/4" @ 2-3/4"LONG
SCREW:#10 x 3/4" THSMS
FLUSH WITHJAMB BOTTOM
Dim A = Depth (-) 1-3/16"(assuming 1/2" backbends)
Dim A
Dim A
Dim A = Depth (-) 3/16"
FLOOR
FLOOR
IMPOST
IMPOST
Note: Anchor is attached to floor attwo places. Mullion or sill is slippedover anchor (fastening is optional).
12 GAGESTEEL
(2) 9/32"DIA. HOLES
Note: Position sill anchorto avoid possible interferencewith sill bracing strap ifpresent.
SILL BRACINGSTRAP
FOR VERTICAL MULLIONS
FOR BASE SILLS
NOMINAL SIZES
SIDELITE FLOOR ANCHOR
11-503
11-504
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataANCHORS FOR NEW MASONRY
1-13/16"
8-1/4"
2"
8"
R 1-1/4"
2-5/16"9-3/8"
2"
MASONRY "T" ANCHOR
WIRE MASONRY ANCHOR
SPOTWELDED
16 GAGEGALV STEEL
DEPTH
6-3/4
7-3/4
8-3/4
4-3/4
5-3/4
DEPTH
5-1/4
4-1/4
4-1/44-3/4 3-3/4
3-3/4
MFGFIELD MODIFIED DEPTH
THROAT RANGE
2 THRU 8-3/4
All dimensions are in inches; forSI conversion, 1" = 25.4 mm.
All dimensions are in inches. For SI conversion: 1" = 25.4mm.Dimension A assumes a 5/8 frame stop height.Suggested Rough-opening clearance: 1/4" @ head and jambs.See page 11-506 for jamb punching, spacing, fastener, and floor anchor notes.
The wood stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe attached at each sill in lieu of a floor anchor.
18 GAGESTEEL
WOOD STUD ANCHOR SELECTION CHART
STUD SIZE
2 x 4
2 x 6
DIM "X"
3-1/2
5-1/2
INSTALLATION SEQUENCE1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL
* Or to suit other stud sizes.For stud sizes other than shownbelow: actual stud dimension shouldbe noted. Also, wall board thicknessesshould be shown so that straps canbe properly positioned.
PORTION OF JAMBREMOVED FOR CLARITY
Straps are nailed
STRAP ANCHOR
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
NOMINAL SIZES
ADJUSTABLE JAMB ANCHORFOR STUD WALLS
11-509
ASSEMBLY DETAIL(END VIEW)
Anchors are adjustable in 1/8"increments within given ranges.
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataWELDED METAL STUD ANCHOR RECESSED TYPE
5/8
DIM "A"
EQUAL
EQUAL
JAMB
WALL SECTION
The metal stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe provided for each sill.
18 GAGESTEEL
Stud isscrewedto anchor
If second studis used, attachit after jambis fastened.
2. WALL FRAMING1. DOOR FRAMEINSTALLATION SEQUENCE
3. WALL SURFACE MATERIAL
3-1/2 4-1/2 THRU 5-1/4
8-3/8 THRU 9-3/4
5-3/8 THRU 6-3/4
6-7/8 THRU 8-1/46-1/2
8
5
DEPTH RANGEDIM"A"
FRAME
ZEE ANCHOR (1x1-1/4x1 @ Dim "A" long)SPOT WELDED TO JAMB
MSZ anchor andstop as necessary
clip is welded tox 1 long steel "zee"a 3/4 x 5/8 x 3/4depths over 4 inches,For single rabbet
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
NOMINAL SIZES
WELDED METAL STUD ANCHORFLUSH TYPE
11-511
DIM "C"DIM "A"
DIM "B"
DIM "B"
Allow 3/16" clearancebetween studand jamb
The metal stud anchor depicted below is shop attached. at sill.
For single rabbetdepths over 4 inches,a 3/4 x 5/8 x 3/4x 1 long steel "zee"clip is welded toMSZ anchor andstop as necessary
Stud isscrewed to anchor
Series BQ shouldbe considered
If second studis used, attachit after jambis fastened.
4-5/85-7/8
7-1/2 2-1/8
1-7/16
13/16
3-1/43
3 5-3/8 THRU 66-1/8 THRU 7-5/8
7-3/4 THRU 9-1/4
DIM"A" "B"
DIM"C"DIM FRAME
DEPTH RANGE
Anchor is normally positioned in the center ofthroat to accommodate equal thicknesses ofwallboard at each side of stud. If wall is notsymmetrical, drawings showing condition shouldbe provided.
INSTALLATION SEQUENCE
1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL
16 GAGESTEEL
Shim
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
Designate if floor anchor or jamb anchor is desired
5-5/8
3/4
CL
CL
1-1/16
STUDSIZE
9/16
7/32 R.
3/41-5/16
4
1/2" BACKBENDS
BEND HERE FOR ONELAYER OF 1/2" > 5/8"
BEND HERE FOR TWOLAYERS OF 1/2" > 5/8"
FOR 2"FACE
18 GAGEGALV STEEL
NOTEFRAME IS SET-UP
AND JAMBS ANCHOREDBEFORE WALLBOARD IS
INSTALLED.
ANCHORS ARE BENT INFIELD TO THICKNESSOF WALLBOARD. IFWALL FRAME WORK ISSET UP BEFORE DOORFRAME, USE ANADDITIONAL JAMB ANCHORAT SILL INSTEAD OFSILL ANCHOR.
Frame components should have open ends.Mitered corners prevent spline installationwithout modification of backbend.Allot one spline for every 2 feet of impostheight. Drive spline in from ends, locateapprox. equal distance from one another.
For shipping via common carrier,frame size should not exceed8'-0" in more than one dimension.
SPLINE APPLICATION(For Custom Depths)
NOMINAL SIZES
FRAME INSTALLATIONMASONRY AND STUD WALLS
11-901
DOOR OPG AT HEAD
FRA
ME
DEP
TH
JOBSITE STORAGE: Store frames off the ground on wood runners or skids. Do not storedirectly on the ground. Cover frames with tarpaulin or plastic but do insure that adequate
When frames are to be fully grouted and when plaster or mortar contain "anti-freeze" agents,the inside of the frames should be coated with a bituminous, water-resistant paint by theinstallation contractor.
ventilation is provided to eliminate moisture condensation.
Typical wood spreader must be square and madefrom lumber at least 1" thick. Length of spreaderequals door opening width at the head. Cut clear-ance notches for frame stops as shown. Spreadermust be nearly as wide as frame depth for properinstallation.
The installer should use wood spreaders (asdescribed at right), a carpenters level (thelonger the better), and a carpenters square(the bigger the better). Set the frame inthe desired location. Level head and plumbjambs. Shim under jambs if necessary.
SLOTS FORCORNER TABS
CORNER TABS BEND CORNER TABSTOWARD INSIDE OFFRAME
SLOTS FORJAMB TABS
BEND JAMB TABSTOWARD OUTSIDEOF FRAME
JAMB TABS
HEAD JAMB
CORNERASSEMBLY
Install rubber silencers beforeframe is setup to avoid groutplugging holes.
ASSEMBLY of FRAME
SQUARING THE FRAME SPREADER
PLUMBING FRAME
90˚
NOMINAL SIZES
FRAME SPREADER BARS
11-903
This bar is not to be used for installation. A wood spreader is to be used for maintainingproper spacing between jambs. (See the DHI publication "The Installation of CommercialSteel Doors and Steel Frames", "Insulated Steel Doors in Wood Frames", and "Builder'sHardware").
3. SPREADER BAR QUANTITY AND LOCATION
A. All single rabbet frames and double rabbet, single swing frames with depth not exceeding 6 inches: attach (1) spreader bar to the door rabbet. (See Fig. #1)
B. All double rabbet, double swing frames or double rabbet, single swing frames with depth exceeding 6 inches: attach one (1) spreader bar to each frame rabbet (two total).
(see Fig. #2)
4. SPREADER BAR ATTACHMENT
Verify spreader bar length by checking to see that said length is equivalent to the door opening width dimension at head. Place the spreader bar at the bottom of the door opening and tack weld in place. Strength of welds should be such that spreader bar remains in place during transit and also be such that the spreader bar can be removed when required (by means of a sharp hammer blow) without incurring frame damage.
1. SPREADER BAR PROFILE 2. SPREADER BAR LENGTH
Length of spreader bar is equivalent to door opening width dimension.