7/28/2019 Disassemble of ZV06
1/12
U P G R A D E & R E P L A C E M E N T
5 - 1
Upgrade & Replacement
Follow the individual procedures in this chapter to perform thenotebooks upgrade and replacement of various majorcomponents.
sus M6000 Series Notebook is not an all-in-one product. The keyupgradeable and replaceable items include the Memory module, HDDmodule, Optical Drive module, CPU Module
Be sure to follow the safety instructions described in Chapter 2 to safeguard the
notebook against any potential damages. For any other components not covered
in this chapter which you need to replace, please refer to Chapters 3 and 4 for detaileddisassembly and assembly and perform necessary procedures accordingly.
This chapter includes the following items:
Upgrade and Replacement for HDD Module
Upgrade and Replacement for Memory ModuleSecond Memory ModuleFirst Memory Module
Upgrade and Replacement for CPU Module
Upgrade and Replacement for Mini-PCI Adapter
Chapter
A
7/28/2019 Disassemble of ZV06
2/12
U P G R A D E & R E P L A C E M E N T
5 - 2
Upgrade and Replacement for HDD Moudle
The M6000 series Notebook uses an industry-standard 2 HDD with IDE interface.You can replace the HDD to any capacity of your choice within our approval andprior test
First, remove AC-power and battery
1. Remove 2 screws (M2*6L(K)) and take the hard disk cover off. Hold the arrowand pull out the HDD module then take it away.
2. Remove 2 screw (M2*4L(K)) on both sides
3. Separate hard disk from the housing
H D D M O D U L E
M2*6L
7/28/2019 Disassemble of ZV06
3/12
U P G R A D E & R E P L A C E M E N T
5 - 3
4. Replace the new Hard-Disk onto the HDD Housing.
5. Secure 2 screws (M2*4L) on both sides
6. Insert the hard disk moudule into its compartment and lay it down gentlythen put on the hard disk cover. And secure 2 screws (M2*6L(K)).
Upgrade and Replacement for Memory ModuleThe M6000 Series Notebook do not have onboard RAM. There are twoSO-DIMM sockets for installing SO-DIMM RAM. It can upgrade the totalmemory size up to 1GB with a 512MB module on each socket.
M E M O R Y
M O D U L E
M2.5*6L
7/28/2019 Disassemble of ZV06
4/12
U P G R A D E & R E P L A C E M E N T
5 - 4
First, remove AC-power and battery.
Upgrading Second Memory Module1. Remove 2 screws (M2*3L(K) ) and take the memory DIMM cover away.
2. Insert the new memory module to DIMM socket at 45 degrees angle and push itdown to lock it up. Put on the memory DIMM cover and secure 2 screws(M2*3L(K) ) to fix it.
First, remove AC-power and battery.
Upgrading First Memory Module
1. Remove 2 screws (M2.5*6L(K)) at bottom side then turn back the notebook anduse tweezers to unlock 3 keyboard latches.
S E C O N D
M E M O R Y
M O D U L E
F I R S T
M E M O R Y
M O D U L E
M2*3L
M2*3L
M2.5*6L
7/28/2019 Disassemble of ZV06
5/12
U P G R A D E & R E P L A C E M E N T
5 - 5
2. Pull out the keyboard module and then lay on the top case. Open the two latches
to pop up memory module 45 degrees angle and push it down to lock it up.
3. Insert the new memory module to DIMM 45 degrees angle and push it down tolock it up. Install the keyboard module onto top case and secure 2 screws(M2.5*6L(K)) at bottom side then fix it.
Upgrade and Replacement for CPU ModuleThe M6000 Series Notebook comes standard with a Intels FC-PGA Socket on the
motherboard, which means it can support all FC-PGA CPUs up to 1.7 GHz.
First, remove AC-power and battery.1. Remove 2 screws (M2.5*6L(K)) at bottom side then turn back the notebook and
use tweezers to unlock 3 keyboard latches.
C P U M O D U L E
C P U
R E M O V A L
M2.5*6L
7/28/2019 Disassemble of ZV06
6/12
U P G R A D E & R E P L A C E M E N T
5 - 6
2. Pull out the keyboard module and then lay on the top case. Disconnect keyboard
FPC cable and take the keyboard away.
3. Remove 2 screws (M2*3L(K)) at keyboard cover and use tweezers to lift up thekeyboard covers two nooks.
4. Slide the FAN bracket left then take it away. Remove 4 screws (M2*6L(K)) atheat sink.
M2.5*6L
M2*3L
7/28/2019 Disassemble of ZV06
7/12
U P G R A D E & R E P L A C E M E N T
5 - 7
5. Remove Thermal module and open the CPU Sockets latch to loosen theCPU.(The use the CPU vacuum hand pump to suck up the CPU and lift the
CPU away.)
6. Insert the new CPU onto the socket then close the CPU Sockets latch to fix it.
7. Paste thermal pad onto the CPU heat sink module then install it.
7/28/2019 Disassemble of ZV06
8/12
U P G R A D E & R E P L A C E M E N T
5 - 8
8. Secure 4 screws to fix it and stick the warranty seal label on the screw.
9. Put on FAN bracket properly.
10.Install the keyboard cover then secure 2 screws (M2*3L(K)) to fix it.
7/28/2019 Disassemble of ZV06
9/12
U P G R A D E & R E P L A C E M E N T
5 - 9
11.Install the keyboard module onto top case and secure 2 screws (M2.5*6L(K)) atbottom side then fix it.
Upgrade and Replacement for Mini-PCI Adapter
First, remove AC-power and battery.
1. Remove 2 screws (M2.5*6L(K)) at bottom side then turn back the notebook anduse tweezers to unlock 3 keyboard latches.
2. Pull out the keyboard module and then lay on the top case. Disconnect keyboardFPC cable and take the keyboard away.
O P T I C A L
D R I V E R
R E P L A C E M E N T
M2*3L
M2.5*6L
M2.5*6L
7/28/2019 Disassemble of ZV06
10/12
U P G R A D E & R E P L A C E M E N T
5 - 10
3. Remove 2 screws (M2*3L(K)) at keyboard cover and use tweezers to lift up thekeyboard covers two nooks.
4. Remove 1 screw (M2*3L(K)) at mini-PCI cover and take it off
5. Disconnect the two antenna cables then open the two latches to pop up wirelessWLAN module 45 degrees angle and push it down to lock it up.
M2.5*3L
M2*3L
7/28/2019 Disassemble of ZV06
11/12
U P G R A D E & R E P L A C E M E N T
5 - 11
6. Insert the new wireless LAN module to mini-PCI socket at 45 degrees angle andpush it down to lock it up and connect the 2 antenna cables.
7. Put on the mini-PCI cover and secure 1 screw (M2*3L(K)) to fix it.
8. Install the keyboard cover then secure 2 screws (M2*3L(K)) to fix it.
M2*3L
7/28/2019 Disassemble of ZV06
12/12
U P G R A D E & R E P L A C E M E N T
5 - 12
9. Install the keyboard module onto top case and secure 2 screws (M2.5*6L(K)) atbottom side then fix it.
M2*3L
M2.5*6L