-
Installation instruction for 140G-IIstruzioni di
installazioneInstallationsanleitungInstructions pour
l’installationInstrucciones de instalación
Bul. 140G/140MG
DIR 1000720R0001 Version 02
WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free
from contaminants. (Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima
dell'installazione o manutenzione. Installare in custodia idonea.
Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E).
Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in
einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt
werden. (Befolgen Sie die Anforderungen nach NFPA70E).
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou
armoire appropriée. Protéger le produit contre les environnements
agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la
instalación o del servicio, a fin de impedir sacudidas eléctricas.
Instálelo en una caja apropiada. Manténgalo libre de contaminantes.
(Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica
antes de fazer a instalação ou a manutenção. Instalar em caixa
apropriada. Manter livre de contaminantes. (Cumpra as exigências da
norma NFPA70E).
Installation - Installazione - Instalación Instalação - -
DIR 1000720R0001 Version 02 - 140G-I_, 140MG-I_
CLACK
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してください。適切なケース内に取付けてください。また、汚染物質がないことを確認してください。(NFPA70Eの要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备箱内。防止接触污染 。符合NFPA70E要求)物
1
from 0.51" to 0.55"
from 13 mm to 14 mm
dia.
0.1
3"ø 3
.5 m
m
x2
3p
4p
x3
x2
x3
x2
x3
x4
x6
x6
x8
x2
x2
x2
x1
Phasebarrier
End cap kitMounting hardware Insulator Sidecover
Insulator
CH 6
CH 7
140G-G-MH3
140G-G-MH4
140G-G-PB3M
140G-G-PB4M
140G-G-ECM3
140G-G-ECM4
LENGTH M
1 8 mm (0.71") M 8
LENGTH M
73 mm (2.87") M 4
M
M 4
-
1
(2)
2
Maximum recommended conductor support distance
DIR 1000720R0001 Version 02
7.8
7"/
20
0 m
m7
.87
"/2
00
mm
-
- - -
Use cable or insulated busbars/ or perform specific type test on
the installation.Usare cavi o barre isolate/ o eseguire prove di
tipo specifiche sull' installazione.Kabel oder isolierte
Sammelschienen verwenden/ oder die spezifische Typprüfung auf
derInstallation durchführen.Utiliser un câble ou des barres
isolées/ ou réaliser un test de type spécifique sur
installation.Utilizar un cable o barras aisladas/ o efectuar una
prueba de tipo específico sobre instalacíon.
-
-
DIR 1000720R0001 Version 02 (3)
1
2
4
OK
3
3
A B C D E
III2.83"
72 mm
1.85"
47 mm
4.02"
102 mm
0.53"
13.5 mm
2.00"
51.0 mm
IV2.83"
72 mm
1.85"
47 mm
5.39"
137 mm
0.53"
13.5 mm
2.00"
51.0 mm
III-IV3.15"
80 mm
1.69"
43 mm
1.85"
47 mm
0.45"
11.5 mm
0.93"
23.5 mm
III2.95"
75 mm
2.16"
55 mm
4.33"
110 mm
0.69"
17.5 mm
2.16"
55.0 mm
IV2.95"
75 mm
2.16"
55 mm
5.71"
145 mm
0.69"
17.5 mm
2.16"
55.0 mm
WITH ESCUTCHEON
WITHOUT ESCUTCHEON
1,1 Nm
8,9 lb-in
DB
EC
A
Y
X
X
Y
X
Y
Y
X
IV ONLY
IV ONLY
IV ONLY
IV ONLY
IV ONLY
MANDATORY FORUL APPLICATIONNOT REQUIRED FORIEC APPLICATIONS
4
.8"/
12
2 m
m
0.69"/17.5 mm
0.69"/17.5 mm
2.76"/70 mm
2.4
"/6
1 m
m
0.9
8"/
25 m
m
0.98"/25 mm
0.9
8"/
25 m
m
0.98"/25 mm
4
max
9,5
min
10
max 2
5
Ø min 8.50.31"(8) max0.2"(5) min
dia. min 0.33"
max 0
.98" m
ax 0
,37"
min
0,3
9"
25
dia. 0.33"
0.98"
Ø 8.5
-
FC
D
B
E
HG
AI
5
140MG-I MAGNETIC ONLY TRIP UNIT
- Manually trip the breaker prior to adjustment of the magnetic
settings.
- E’obbligatorio mettere l'interruttore in posizione Trip test
prima di regolare il termomagnetico.
- Der Leistungsschalter muss vor Einstellung des
thermomagnetischen Auslösers zwingend in die Prüfstellung
geschaltet werden.
- Il est obligatoire de mettre le disjoncteur en position de
Test de Déclenchement avant de régler le déclencheur
magnétothermique.
- Es obligatorio situar el interruptor en posición “Test de
Disparo” antes de realizar el ajuste del relé termomagnético.
In A B C D E F G H I
100 600 675 750 825 900 975 1050 1125 1200
110 660 743 825 908 990 1073 1150 1238 1320
125 750 844 938 1031 1125 1219 1313 1406 1500
150 900 1013 1125 1238 1350 1463 1575 1688 1800
I3
USE FLAT BLADESCREW DRIVER
140G-I THERMOMAGNETIC TRIP UNIT
1000
I1(4)
100
6
225 2250
Type
160 1600
175 1750
200 2000
110 1100
125 1250
150 1500
80
70 700
90
100
110
800
90 900
100 1000
Fixed
Fixed
175
200
225
125
150
160
70
80
Fixed
Fixed
Fixed
In I1 I3
60
63
60 600
63 630
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
In=100A
I3(4)
CLACK
12
In=200A
A B C D E
I3
F G H I
DIR 1000720R0001 Version 02 (L9174) - B0613 Copyright © 2016
Rockwell Automation, Inc. All Rights Reserved. Printed in
Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are
trademarks of Rockwell Automation, Inc.Trademarks not belonging to
Rockwell Automation are property of their respective companies.
Publication 140G-IN095C-MU-P - January 2016
Rockwell Automation maintains current product environmental
compliance information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
Page 1Page 2Page 3Page 4
-
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS
CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR
DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 0110000028320Dr. DateG. USHAKOW 8-23-13
MATERIALSIZE
FOLD
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
FLAT
SPECIFICATIONS FORINSTRUCTION SHEET CREATED BY STRATEGIC
PARTNER
This Instruction Sheet is Being Printed by Strategic Partner
Note: After folding---Printed in (Country where printed*), part
number(s) and barcode (when used) should be visible.
* The printing vendor may change the instruction sheet files to
show the correct country.