dinotecNET_ready

Simply enjoy the best water!

More functions, more conveniences, superior technology.

Fully equipped pool control system,

completely pre-configured.

d i n o t e c b u s s y s t e m

Simply enjoy the best water!

Full control over the water quality

All models feature a 5.7'' colour touch screen. Clear, logical menu structures allow an intuitive operation. All processes and parameters are clearly and concisely presented. Bus-controlled peristaltic dosage pumps with non-wearing stepper motor.

„ready“ means that you receive a perfectly matched, pre-configured system for control of your swimming pool. Complex system combinations are dispensed with. Due to modern bus technology, the expenses involved in the installation of the dinotecNET+ ready are kept to a minimum. The „intelligent“ system is superior to conventional systems as regards technology, range of functions and modern conveniences. At the same time, the system provides a maximum scope for individualisation. It permits a free choice of the water care method, only the appropriate measurement sets must be connected. In addition, it is possible to further customise the system by means of additional options.

Wired ready for connection and pre-assembled on a plastic wall mounting plate with rapid assembly device

For outdoor and indoor pools with a volume up to about 150 m³

Functions, workflows and settings are clearly and concisely presented.

The colouring of the level indicator allows you to identify the current state at a glance: Blue means everything is alright. Yellow means „Reserve“, a

refilling is required. Red means: Warning, container is empty.

Everything included! Functions and advantages at a glance

Best water quality, measurement and control of all sanitary parameters.

Heating: Measurement of the pool temperature and control of heating circulation pump / 3-way valve.

Expandable to meet future requirements.

Economical use of resources.

Peristaltic dosage pumps with integrated measurement of level in container (in cm). Alarm via system bus.

Filter control for filters with a filter pump 230/400 V up to 4 kW, with integrated time switch for filter running times.

Peristaltic dosage pumps, bus controlled, with non-wearing stepper motor.

Input of water agents as required.

Free choice of water care method: chlorine-free (Poolcare) or with chlorine.

Party mode - water treatment is carried on also outside the set hours of operation, thereby ensuring an optimum water quality.

Holiday mode: energy-saving operation. Activation and automatic return to normal operation by means of the calendar feature.

Solar temperature control for heating the pool water by means of solar absorber systems.

Solar temperature control for cooling the pool water over night by means of solar absorber systems.

Graphical display, information comprehensible at a glance, intuitive operation.

Dosing time control for preventing uncontrolled dosing.

All measured data is stored for more then 1 year.

Connection to a PC, router, printer; direct data transmission via DSL possible.

And more ...

More individuality, more conveniences: optional features

Simply enjoy the best water!

Second, larger touch screen for (remote) control of your entire system from the indoor pool or any other room.

You also own a whirlpool? No problem with the dinotecNET+ ready measuring and control technology for a second pool circulation.

Control your attractions, such as counter current systems, massage nozzles or lighting with the attraction control for up to 3 attractions and 1 floodlight array (up to 600 W). Only together with a second touch screen.

Accessible worldwide. Information retrieval and setting of current values as well as alarm messages via SMS.

Full accessibility to all functions of the system via fixed line.

Improve the filtration performance by means of flocculation! Flocculant dosing station, bus-controlled, 3 – 3000 ml/h.

Balance tank control for pools with overflow gutter. With hydrostatic measured value logging of level.

Control of overflow channel cleaning. Input for key switch.

Automatic filter backwash with lit display for valve size 1 ½“, 2“ or 3“.

Simply enjoy the best water!

Technical data:

adjustable via menu:Priority circuit 'solar'Switching output (solar): voltage-free two-way contact

optional -50 °C to +150 °CCollector sensor:voltage-free two-way contactSwitching output (heating):+5 °C to +40 °CSetting range:Setting range:

manual, optionally automatic (with automatic backwash device Combitrol IMPULS)Backwash:weekly timer freely adjustable, max. 20 switching timesTime switch:

Filter control:

Temperature control:

max. 8.5 l/h with a counter pressure of max. 1.5 bar (adjustable 10 - 100 %)Capacity: stepper motor, non-wearingMotor:peristaltic dosage pumpPump type:dinodos START LEVEL BUSDosage pump:

Alarm: alarm relay (collective alarm) with voltage-free two-way contact

by means of compensation of slope and zero shift, control of slope and zero pointElectrode check: manual with calibration solution pH 7.0 and pH 4.0Calibration:

Slope control: Temperature compensation: yes

yes

adjustableContinuous dosage control: pH raise/pH reduce (switchable)pH control direction:

pH measurement: 0 – 14 pH0.01 pHResolution:

Measuring range: via combined electrode with KCL filling

pH meter and controller:

manual by measurement of the actual content of free chlorine at the measuring cell outlet or in the poolCalibration: by means of compensation of the slope (slope control)Electrode check: adjustableContinuous dosing control: PIDControl type: 0.01 mg/lResolution: 0.0 – 4.0 mg/l chlorineMeasuring range:potentiostatic with chlorine electrode (3-electrode system)Measurement of oxidant:

Chlorine meter and controller (chlorine version):

manual by measurement of the actual content of Poolcare at the measuring cell outlet or in the poolCalibration: by means of compensation of the slope (slope control)Electrode check: adjustableContinuous dosing monitor: PIDControl type: 1 mg/lResolution:0 – 99 mg/l PoolcareMeasuring range: potentiostatic with Poolcare electrode (3-electrode system)Measurement of oxididant:

Poolcare (active oxygen) meter and controller (Poolcare version, chlorine-free):

with rapid assembly device, pre-assembled 720 x 720 mmWall mounting plate:multilingualLanguage:colour graphic display 640 x 480 px

Storage temperature pH electrode:

via touch screenOperation: Control outputs: proportional via bus

-5 °C to 40 °C

Display:

Permissible humidity: max. 90 % at +40 °C (non-condensing) -20 °C to +65 °Cup to +50 °C Permissible ambient temperature:approx. 2.5 kgWeight: approx. 500 x 300 x 150 mmDimensions housing (w x h x d): IP 65Protection class: 50 VAPower consumption: 85 – 265 V/AC (48-63 Hz)Mains voltage:

Until June 2008, the dinotecNET+ ready system is supplied with the Easydos CONCEPT peristaltic dosage pump.

d i n o t e c b u s s y s t e m

Background photo: Water photo no. 1 Artist: Thomas Kuhn

dinotec GmbH Water and Pool Technology Spessartstr.7 63477 Maintal/Germany Telephone: +49(0)6109-6011-0 Fax: +49(0)6109-6011-90 E-mail: [email protected] www.dinotec.de

Simply enjoy the best water!

RH

/Reh

ms

– 1

– 04

/08

Your dinotec specialist dealer:

Subject to technical changes. Errors excepted! 02/2008