8791 Positioner SideControl BASIC p. 1/15 www.burkert.com Yoke type actuators Digital electropneumatic Positioner SideControl Type 8791 BASIC can be combined with… • Compact and robust design • Easy to start using tune function • Dynamic positioning system with no air consumption in controlled state • AS-Interface Fieldbus (optional) • Mounting acc. to IEC 60534-6-1 / VDI VDE 3845 or Remote Technical data Material Body Seal Aluminium plastic-coated EPDM, NBR, FKM Operating voltages 24 V DC +/- 10% Residual ripple max. 10% Setpoint setting 4-20mA (0-20mA adjustable using configurations software) Input resistance 0/4 to 20 mA: 180 Ω Analogue feedback (0-20mA adjustable using configurations softwar) (max. Burden 560Ω) Binary input 0-5 V = log “0”, 10-30 V = log “1” Control medium Dust concentration Particle density Pressure condensation point Oil concetration neutral gases, air, quality classes acc. to ISO 8573-1 Class 7 (<40μm particle size) Class 5 (<10mg/m 3 ) Class 3 (<-20°C) Class X (<25mg/m 3 ) Ambient temperature 0 to +60°C Pilot air ports Threaded ports G 1/4 Supply pressure 1.4 bis 7 bar 1) 2) air supply filter Exchangeable (mesh aperture~0.1mm) Actuator system Air capacity Single and double-acting up to 150 l N /min. 50 l N /min (with 1.4 bar 2) ) for aeration and ventilation 150 l N /min (with 6 bar 2) ) for aeration and ventilation (Q Nn = 100 l N /min (acc. to the definition with decrease in pressure from 7 to bar absolute) Position detection module Potentiometer max. angle 180° Stroke range valve spindle Min. 30º on the rotary shaft, depending on lever Installation As required, display above or sideways Type of protection IP65 and IP67 acc. to EN 60529 (NEMA4x in preparation) Power consumption < 3.5 W continued on next page The robust and compact positioner is designed to a standardisation acc. to IEC 534-6 or VDI/ VDE 3845 for assembly with linear and ro- tary actuators. In addition, the remote version with the displacement position sensor can be combined with Bürkert process control valves The setpoint setting for the electro-pneumatic digital Positioner SideControl BASIC occurs using a standard signal 4…20mA or with AS- Interface as an option. In addition there is a bi- nary input and an optional analogue feedback available. The valve opening is signalled by a mechanical indicator element and the device staus is shown on three coloured LEDs. All the operational elements are found in the housing. The start-up happens automatically, and di- rectly at the device the following functions can be activated through DIP switches: - Close tight function - Inversion of the operating direction of the setpoint signal - Characteristic curves selection - Switching - manual and automatic operation Additional possibilities on configuration and parameter setting, for example, linearisation of the operation characteristics by using com- munications software which allows customised programming. The pilot valve system can be used equally for single and double-acting drives. It is characterised by a defined safety feature in case of failure of the electrical or pneumatic power supply and possesses an enormous air capacity range with pressure supply up to 7 bar. 1) The supply pressure has to be 0.5-1 bar above the minimum required pilot pressure for the valve actuator 2) Pressure values [bar]: Overpressure with respect to atmospheric pressure Rotary actuators with remote positioner Hygienic process control valve with remote positioner Rotary actuators Process control valve with remote positioner
15
Embed
Digital electropneumatic Positioner SideControlburkert.ru/sites/default/files/ds8791-basic-eu-en.pdf · 8791 Positioner SideControl BASIC p. 1/15 Yoke type actuators Digital electropneumatic
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
8791 PositionerSideControl BASIC
p. 1/15www.burkert.com
Yoke type actuators
Digital electropneumatic Positioner SideControl
Type 8791 BASIC can be combined with…
• Compact and robust design
• Easy to start using tune function
• Dynamic positioning system with no air consumption in
controlled state
• AS-Interface Fieldbus (optional)
• Mounting acc. to IEC 60534-6-1 / VDI VDE 3845 or Remote
Technical data
Material
Body
Seal
Aluminium plastic-coated
EPDM, NBR, FKM
Operating voltages 24 V DC +/- 10%
Residual ripple max. 10%
Setpoint setting 4-20mA (0-20mA adjustable using confi gurations software)
Input resistance 0/4 to 20 mA: 180 Ω
Analogue feedback (0-20mA adjustable using configurations softwar)
(max. Burden 560Ω)
Binary input 0-5 V = log “0”, 10-30 V = log “1”
Control medium
Dust concentration
Particle density
Pressure condensation point
Oil concetration
neutral gases, air, quality classes acc. to ISO 8573-1
Class 7 (<40μm particle size)
Class 5 (<10mg/m3)
Class 3 (<-20°C)
Class X (<25mg/m3)
Ambient temperature 0 to +60°C
Pilot air ports Threaded ports G 1/4
Supply pressure 1.4 bis 7 bar 1) 2)
air supply fi lter Exchangeable (mesh aperture~0.1mm)
Actuator system
Air capacity
Single and double-acting up to 150 lN/min.
50 lN/min (with 1.4 bar2)) for aeration and ventilation
150 lN/min (with 6 bar2)) for aeration and ventilation
(QNn
= 100 lN/min (acc. to the defi nition with decrease in
pressure from 7 to bar absolute)
Position detection module Potentiometer max. angle 180°
Stroke range valve spindle Min. 30º on the rotary shaft, depending on lever
Installation As required, display above or sideways
Type of protection IP65 and IP67 acc. to EN 60529 (NEMA4x in preparation)
Power consumption < 3.5 W
continued on next page
The robust and compact positioner is designed
to a standardisation acc. to IEC 534-6 or VDI/
VDE 3845 for assembly with linear and ro-
tary actuators. In addition, the remote version
with the displacement position sensor can be
combined with Bürkert process control valves
The setpoint setting for the electro-pneumatic
digital Positioner SideControl BASIC occurs
using a standard signal 4…20mA or with AS-
Interface as an option. In addition there is a bi-
nary input and an optional analogue feedback
available. The valve opening is signalled by a
mechanical indicator element and the device
staus is shown on three coloured LEDs. All the
operational elements are found in the housing.
The start-up happens automatically, and di-
rectly at the device the following functions can
be activated through DIP switches:
- Close tight function
- Inversion of the operating direction of the
setpoint signal
- Characteristic curves selection
- Switching - manual and automatic operation
Additional possibilities on confi guration and
parameter setting, for example, linearisation
of the operation characteristics by using com-
munications software which allows customised
programming. The pilot valve system can be
used equally for single and double-acting
drives. It is characterised by a defi ned safety
feature in case of failure of the electrical or
pneumatic power supply and possesses an
enormous air capacity range with pressure
supply up to 7 bar.
1) The supply pressure has to be 0.5-1 bar above the minimum required pilot pressure for the valve actuator2) Pressure values [bar]: Overpressure with respect to atmospheric pressure
Rotary
actuators with
remote positioner
Hygienic process
control valve with
remote positioner
Rotary
actuators
Process control
valve with remote
positioner
8791 Positioner SideControl BASIC
p. 2/15
Technical data
Electrical connection
Multipole connection
Cable gland
Remote Version
M12, 8-pin
2xM20x1.5 (cable Ø 10mm) on screw terminals
(0.14-1.5 mm2)
1xM12x1.5 (cable Ø 3 to 6.5 mm)
Protection class 3 acc. to DIN EN 61140
Type of ignition protection II 3 G nA IIC T4
II 3 D tD A22 T135° C
Conformity EMC directive 2014/30/EU
CSA approval information
Product category code Class 3221 82-VALVES - Actuators - Certifi ed to US standards
Class 3221 02-VALVES - Actuators
Considered standards CAN/CSA-C22 2 No. 139
UL 429
CSA trademark
Technical data, continued
Technical data - Linear Remote Position Sensor (ELEMENT, CLASSIC)
1xM16x1.5 (cable Ø 5-10 mm) on terminal screws (0.14-1.5 mm²) 10 m
Operating voltage 24V DC ± 10 %, UL: NEC Class 2
Power consumption < 0.3 W
Sensor measurement range 3 to 45 mm (Stroke range valve spindle)
Actual position signal digital (RS485)
Ambient temperature -25 to +80 °C
Protection class 3 acc. to DIN EN 61140
Type of protection IP65 and IP67 acc. to EN 60529, Type 4X
Type of Ignition protection II 3D Ex tc IIIC T135 ºC Dc
II 3G Ex nA IIC T4 Gc
Conformity EMC directive 2014/30/EU
Approvals cCSAus, cULus Certifi cate no. 238179
Using a remote positioner the length of the control air pipes infl uences the dynamics and attain-
able accuracy of the position control loop. The length of the control air pipes therefore should be as
short as possible.
Technical data - AS-interface (Option)
Profi le S-7.3.4 Output: 16 Bit Set point/Certifi cate No. 87301 acc. to Version 3.0S-7.A.5 Output: 16 Bit set point; Input: 16 Bit feedback/certifi cate No. 95401 acc. to Version 3.0
Programmed data see instruction manual
Operating voltage over Bus connection
29,5 to 31,6 VDC acc. to Specifi cation
Max. current consumption 150 mA
Electrical connection M12x1,4-pin stainless steel connection assembled with 80cm cable and fl at cable clamp
Technical data - Position feedback with proximity switches (Accessory)
Electrical connection M12, 4-pin
Output function 3-wire, normally open contact, PNP
Operating voltage 10 to 30 V DC
Residual ripple ≤ 10% Uss
DC rated current ≤ 100 mA
Type of protection IP65 and IP67
Protection class 3 acc. to DIN EN 61140
Conformity EMC directive 2014/30/EU
Approvals cCSAus
Note: The position feedback has two
proximity switches which are independently
adjustable via switch lugs.
Technical data - rotative Remote Postion Sensor (NAMUR)
Electrical connection 2 m round cable (shielded)
Operating voltage 10 to 30 V DC
Power consumption < 0.8W
Sensor measurement range 0° to 360°
Actual position signal digital (RS485)
Ambient temperature -25 to +80°C
Protection class 3 acc. to DIN EN 61140
Type of protection IP65 acc.to EN 60529
Conformity EMC directive 2014/30/EU
Approvals UL (cULus) Certifi cate no. E226909
8791 Positioner SideControl BASIC
p. 3/15
Example of assembly variations of Positioner SideControl
Positioner SideControl Type 8791 BASIC
Linear actuators
IEC 60534-6-1
Rotary
actuators
VDI/VDE 3845
(IEC 60534-6-2)
Type 8798
Sensor Remote
NAMUR
+
Type 8791
BASIC
Remote
Linear actuators
IEC 60534-6-1
Rotary
actuators
VDI/VDE 3845
(IEC 60534-6-2)
Type 8805
+
Type 8791 BASIC
Control valve
system
Type 2300
+
Type 8798
Remote
Position
Sensor
+
Type 8791
BASIC
Remote
Control valve
system
Type 2702
+
Type 8798
Remote
Position
Sensor
+
Type 8791
BASIC
Remote
8791 NAMUR 8791 Remote
Positioner 8791
BASIC
Remote IP20*
* Note: Remote IP20 version exclusively for cabinet mounting
8791 Positioner SideControl BASIC
p. 4/15
Assembly options
NAMUR Version (Positioner with integrated position sensor, assembly acc. to NAMUR/IEC 60534-6-1 and VDI/VDE 3845 (IEC 60534-6-2))
Assembly on linear actuator
Dimensions [mm]
Assembly bridge Adapter kit
Description Item no.
Adapter kit 787 215
Assembly on rotary actuator
1
2
3
4
5
Description Item no.
Adapter kit 787 338
Assembly bridge 770 294
( B )
A
107,6
C
30
50
R7 19,5
R34
Actuator shaft
height
A B C
20 46.5 80 -
30 56.5 80 130
50 76.5 - 130
Position feedback with proximity switches
(upgrade feature for SideControl BASIC)
External position indicator
Coverfor standard display element
Housing cover
Description Item no.
Position feedback 677 218
8791 Positioner SideControl BASIC
p. 5/15
Assembly on DIN-Rail
Dimensions [mm]
Dimensions [mm]
Assembly options continued
Remote version(Remote positioner from actuator with displacement position)
Assembly with accessory brackets
The adapter can be turned
every 90º on the DIN-Rail
Description Item no.
Assembly bracket for wall mounting 675 715
Description Item no.
DIN rail assembly kit 675 702
8791 Positioner SideControl BASIC
p. 6/15
Assembly options continued
Remote version(Remote positioner from actuator with displacement position sensor)
Type 8798
Dimensions
Control valves CLASSIC Types 27xx
Control valve ELEMENT Types 23xx
Description Item no.
Standard ATEX II 3 GD
Remote Position Sensor
Control valves CLASSIC Types 27xx
Control valves ELEMENT Types 23xx
211 535
212 360
226 859
226 860
Description Item no.
Remote Position Sensor NAMUR 211 536
8791 Positioner SideControl BASIC
p. 7/15
Dimensions
36.1 6
4
46
20
SW 17
91
80 50
40 23.5 5
8
Mounting on control valves according to NAMUR (IEC 60534-6-1 / VDI/VDE 3845 (IEC 60534-6-2))
8791 Positioner SideControl BASIC
p. 8/15
Further versions on requesti
Ordering Chart (further version on request)
Positioner SideControl Basic Type 8791
Asse
mb
ly
va
ria
tio
ns
Co
ntr
ol
fun
cti
on
Pil
ot
va
lve
syste
m /
Air
ca
pa
cit
y
Co
mm
un
ica
tio
n
Ele
ctr
ica
l co
nn
ecti
on
Bin
ary
in
pu
t
An
alo
gu
e
fee
db
ack
ATE
X I
I 3 G
D
Ite
m N
o.
NAMUR IEC 60534-6-1
VDI/VDE 3845 (IEC 60534-6-2)
single and
double-actinguniversal
no
Cable gland
yes no 211 521
yes yes 211 522
yes no yes 226 834
yes yes yes 226 835
Multipole
yes no 211 523
yes yes 211 524
yes no yes 226 836
yes yes yes 226 837
AS-
Interface
no yes/16 bit 239 617
no yes/16 bit yes 239 618
Asse
mb
ly
va
ria
tio
ns
Actu
ato
r siz
e
Co
ntr
ol
fun
cti
on
Pil
ot
va
lve
syste
m /
Air
ca
pa
cit
y
Co
mm
un
ica
tio
n
Ele
ctr
ica
l co
nn
ecti
on
Bin
ary
in
pu
t
An
alo
gu
e
fee
db
ack
ATE
X I
I 3 G
D
Ite
m N
o.
Remote
ELEMENT 70/90
CLASSIC 80/100single-acting low
no Cable gland
yes no 224 868
yes yes 224 869
ELEMENT 130
CLASSIC 125-225
single and
double-acting universal
yes no 211 531
yes yes 211 532
Remote IP20
ELEMENT 70/90
CLASSIC 80/100single-acting low
yes no 234 576
yes yes 234 578
ELEMENT 130
CLASSIC 125-225
single and
double-acting universal
yes no 211 533
yes yes 211 534
Positioner BASIC Remote IP20 with actual value for potentiometer signal
ApprovalsProtection type: NEMA 4xRemote Sensor ATEX Cat. 3
Asse
mb
ly
va
ria
tio
ns
Ele
ctr
ica
l co
nn
ecti
on
Ite
m N
o.
Remote Position Sensor Standard ATEX II 3 GD
CLASSIC Type 27xx Cable gland - 10 m round cable 211 535 226 859
ELEMENT Type 23xx Cable gland - 10 m round cable 212 360 226 860