Revisions and Errata List AISC Steel Design Guide 9, 2nd Printing (Printed Copy) August 20, 2020 The following list represents corrections to the second printing of AISC Design Guide 9, Torsional Analysis of Structural Steel Members. Page(s) Item 4 In Figure 2.3, in the upper right hand diagram, 2 u we H should be replaced with u we H . 4 In Figure 2.3, in the lower right hand diagram, 2 u we H should be replaced with u we H . 21 In the left column, beginning with the 5 th line from the bottom, replace the existing text as follows: From Example 5.1, 90 kip-in. 45 kip-in. 2 (4.4) 2 45kip-in. 2( in.)(9.5in. 5.5in.) 0.861 ksi u u t o T T tA 2 In the right column, replace the first four lines with the following: Calculate Combined Stress (4.10) 0.75 ksi 0.861ksi 1.61 ksi uv b t f 22 In the table at the top of the first column, the value of f uv for the TS10x6x2 should be changed from 2.47 ksi to 1.61 ksi. 26 In Example 5.4 under the heading, Calculate Maximum Rotation, the calculations should be replaced with: From Appendix B, Case 3 with = 0.3, it is estimated that the maximum rotation will occur at 12.75 ft from the left end of the beam (Point A). At this location, z/l = 0.51 for T B and z/l = 1 0.51 = 0.49 for T D . The service-load torques are T B = (210 kips)(3 in.) = 630 kip-in. 1
5
Embed
DG 9 - Revisions and Errata List-Printed Copy Aug 2020...Microsoft Word - DG 9 - Revisions and Errata List-Printed Copy_Aug 2020.doc Author matthew Created Date 8/20/2020 2:52:35 PM
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Revisions and Errata List AISC Steel Design Guide 9, 2nd Printing (Printed Copy) August 20, 2020 The following list represents corrections to the second printing of AISC Design Guide 9, Torsional Analysis of Structural Steel Members. Page(s) Item
4 In Figure 2.3, in the upper right hand diagram, 2
uw e
H should be replaced with uw e
H.
4 In Figure 2.3, in the lower right hand diagram, 2
uw e
H should be replaced with uw e
H.
21 In the left column, beginning with the 5th line from the bottom, replace the existing text as follows:
From Example 5.1,
90 kip-in.45kip-in.
2
(4.4)2
45kip-in.2( in.)(9.5in. 5.5in.)
0.861 ksi
u
ut
o
T
TtA
2
In the right column, replace the first four lines with the following: Calculate Combined Stress
(4.10)
0.75 ksi 0.861ksi
1.61 ksi
uv b tf
22 In the table at the top of the first column, the value of fuv
for the TS10x6x2 should be changed from 2.47 ksi to 1.61 ksi.
26 In Example 5.4 under the heading, Calculate Maximum Rotation, the calculations should be replaced with:
From Appendix B, Case 3 with = 0.3, it is estimated that the maximum rotation will occur at 12.75 ft from the left end of the beam (Point A). At this location, z/l = 0.51 for TB and z/l = 1 0.51 = 0.49 for TD. The service-load torques are
TB = (210 kips)(3 in.) = 630 kip-in.
1
TD = (285 kips)(3 in.) = 855 kip-in. The maximum rotation is
58 In the upper table, for the Torsional End Restraint for the Left End and Right End,
replace “Fixed” with “Pinned.” To the right of that, “Concentrated torques at ends of member with fixed ends” should be replaced with “Concentrated torque at 0.1 on member with pinned ends.”
58 In the lower table, for the Torsional End Restraint for the Left End and Right End,
replace “Fixed” with “Pinned.” To the right of that, “Concentrated torques at ends of member with fixed ends” should be replaced with “Concentrated torque at 0.1 on member with pinned ends.”
59 In the upper table, for the Torsional End Restraint for the Left End and Right End,
replace “Fixed” with “Pinned.” To the right of that, “Concentrated torques at ends of member with fixed ends” should be replaced with “Concentrated torque at 0.1 on member with pinned ends.”
59 In the lower table, for the Torsional End Restraint for the Left End and Right End,
replace “Fixed” with “Pinned.” To the right of that, “Concentrated torques at ends of member with fixed ends” should be replaced with “Concentrated torque at 0.1 on member with pinned ends.”
2
60 In the top graph, the y-axis values “1.5, 1.25, 1.0, 0.75, 0.5, 0.25,” should be replaced
with “0.15, 0.125, 0.1, 0.075, 0.05, 0.025.”
67 Replace the top graph for GJ
t
with:
77 The variable description for the bottom graph should be revised to:
210GJ a
t l
102 Replace the top graph for 2
1GJ
t a
with:
3
Replace the bottom graph for 1GJ
t a
with:
103 Replace the top graph for 4GJ
t
with:
Replace the bottom graph for 2GJ
at
with:
4
107 Equation C.9 should be changed to:
3
cosh sinh6
z z tzA Bz C D
a a GJl
108 In the right column, Equation C.17 should be changed to:
0
dss
ws nsS W t
112 For Case 11, the equation for should be changed to: