Devices & Networks SITRAIN © Siemens AG 2009. All rights reserved.

Devices & Networks

SITRAIN

© Siemens AG 2009. All rights reserved.

Devices & Networks

SITRAIN

© Siemens AG 2009. All rights reserved.

SITRAINST-MICRO1 / Geräte und Netze Page 3 Siemens AG © 2009

Learning targets

The participant should ...

... be able to create and parameterize a required configuration

... be able to read out and parameterize an actual configuration

... become familiar with addressing the input and output modulesof an S7-1200

... be able to adapt an existing hardware configuration to available hardware


Assign an IP addressfor the programming device / PC

Network Connections

Control Panel

Local Area Connection


Accessible devices in the portal view


Accessible devices in the project view


Upload actual configuration into programming device (1): Add unspecific CPU

Select unspecific CPU


Accessible devices in target subnet:

Device Device type Type Address

PLC_1 CPU1214C DC/DC/DC TCP/IP 192.168.111.1HMI_1 SIMATIC-HMI TCP/IP 192.168.111.2

Load

Upload actual configuration into programming device (2): Detect accessible devices

The device is unspecified

-> Please use the hardware catalog to specify the CPU

-> or detect the configuration for the connected device

Select an accessible device

Detect accessible devices

Add


Upload actual configuration into programming device (3): Read out actual configuration


Required configuration


Open device and network editor


Layout of the device and network editor


Hardware catalog

Information

Enter the searched term

Filter function


Depot for unplugged modules

Open / close depot


PLC properties: PROFINET interface

192.168.111.001 192.168.111.050

Select existing subnet

Set up a new subnet


PLC properties: Digital inputs

Process interrupt(event)

Assignment of event to interrupt

Pulse catch:Pulses that are shorter than the cycle time can

be detected


PLC properties: Digital outputs


PLC properties: Analog inputs

Conversion time

Fixed measuring range 0 to 10 V

Enable diagnostic interrupt (OB82)


PLC properties: High-speed counters (HSC)

Activate counter

Counting modes:- Counting- Frequency

Operating phase:- Single phase- Two phase- A/B Quadrature 1X- A/B Quadrature 4X


PLC properties: Startup mode

Warm restart: Non-retentive memory areas are erased or reset to the start values


PLC properties: Time

Time zone

Changeover between standard and daylight

saving time


PLC properties: Protection


PLC properties: System and clock memory


Insert / delete / change modules

You can use drag-and-drop to also insert modules between modules that have already been plugged.


Signal board

Signal boards can be used to increase the number of CPU-specific inputs and outputs.


Interconnect devices in the network view

Select interface


Connect and disconnect

Lock symbol

Connection symbol

Select interface


Compile hardware configuration

Select PLC

Warnings and errors in info area


Download hardware configuration into device (1)

Short-cut menu

of the station

Accessible nodes


Download hardware configuration into device (2)

Before the download

After the download


Exercise 1-1: Delete old projects

Right mouse button


Exercise 1-2: Assign an IP address for the programming device

Network Connections

Control Panel

Local Area Connection


Exercise 1-3: Delete entries for non-existent projects


Exercise 1-4: Reset CPU to factory settings


Exercise 1-5: Assign an IP address to a CPU

Rightmouse button


Exercise 1-6: Create new project


Exercise 1-7: Add new device


Exercise 1-8: Read out actual configuration


Exercise 1-9: CPU properties:Addressing the integrated inputs and outputs


Exercise 1-10: CPU properties:Parameterize clock memory byte


Exercise 1-11: Parameterize analog module: Measurement type, voltage range, smoothing


Exercise 1-12: Analog module: Parameterize I/O addresses


Exercise 1-13: Mixed DI/DO module: Parameterize I/O addresses


If you want to know more ...

Devices & Networks SITRAIN © Siemens AG 2009. All rights reserved.

Documents

time slide

download slide

interface slide

actual configuration

required configuration

available hardware slide

network editor slide

unspecific cpu slide