Department of Science & Technology upto 2:00 P.M.

Government of Jharkhand

Department of Science & Technology Nepal House, Doranda, Ranchi-834002

Ph. 91-651-2490070, Fax-91-651-2490208

Email: [email protected]

TENDER NOTICE – ET – 01/2014-15

Tenders are invited from the Manufacturers / Dealers for the supply of Machinery / Equipments

for Government Polytechnics under the control of Department of Science & Technology,

Jharkhand. The estimated cost of different packages, date of publication and last date of

submission are mentioned below:

Sl.No. Package No. Tender Document Approximate Cost (Rs.

in Lakh)

01. DST-01 Computer & other accessories 100.00

02. DST-02 Electrical 100.00

03. DST-03 Mechanical 100.00

04. DST-04 Civil 100.00

05. DST-05 Electronics 100.00

06. DST-06 Mining & Drilling 30.00

07. DST-07 Metallurgy 40.00

08. DST-08 Physics & Chemistry 10.00

Date of publication of tender on website : 12.02.2015

Date & Time of Pre-bid Meeting : 19.02.2015 at 11:30 A.M.

Starting Date of submission of bids : 16.02.2015

Last date & time of submission of bids : 10.03.2015 upto 2:00 P.M.

Name and address of Office inviting tender: Department of Science & Technology

Nepal House, Doranda, Ranchi-834002 Further details can be seen and downloaded from the website: www.jharkhand.gov.in , see Tenders

Deputy Director

Department of Science

& Technology

Government of Jharkhand

Department of Science & Technology Nepal House, Doranda, Ranchi-834002

Ph. 91-651-2490070, Fax-91-651-2490208

Email: [email protected]

TENDER NOTICE – ET – 01/2014-15

Sealed tenders for the purchase of Machinery / Equipments, except available on DGS&D rates,

(Computer and other accessories / Electrical/ Mechanical/ Civil/ Electronics/ Mining & Drilling/

Metallurgy/ Physics & Chemistry) separately for each package (from Sl No 01-08) are hereby

invited only from the Manufacturers / Dealers on the prescribed form available on the web site

(www.jharkhand.gov.in) of the Department of Science & Technology, Jharkhand. The tender

documents shall be downloaded from the website and the tender cost of Rs.10,000.00 (Rs. Ten

thousand) only for each package (from Sl No 01-08) separately should be paid through bank

demand draft drawn on any Nationalized Bank in favor of The Director, Department of Science

& Technology, Jharkhand, Payable at Ranchi in a separate envelope.

The tender document containing “Technical Bid” (along with soft copy of proforma for

Technical Specification) and “Financial Bid” (along with soft copy of proforma for Financial

Bid), complete in all respect should reach in the office of The Deputy Secretary, Department of

Science & Technology, Jharkhand, Ranchi, Nepal House, Doranda -834002 on or before

10.03.2015 upto 2:00 P.M. which will be opened on 10.03.2015 at 4:00 PM in the

presence of the tenderers or their representatives (with authorization letter) who may like to be

present during opening. The tender document can be downloaded from the website

http://www.jharkhand.gov.in/web/guest/tenders from the date of publication of this tender notice

and will close on the date specified in the tender document.

The interested vendors fulfilling our terms & conditions should quote their minimum rates (rate

should be F.O.R. to destination inclusive of all Taxes, Duties, and Freight) along with Earnest

Money as mentioned in the tender document in sealed cover duly super scribed as “Tender for

the Purchase of package no. Equipments” on the envelope as per the packages given below.

All the vendors should also give a brief resume about their firm/company, their turnover and

institutions / organizations to which they have supplied quoted items should also be mentioned.

Department of Science & Technology, Jharkhand, reserves the right to reject all or any of the

tenders without assigning any reason thereof. The tender that is incomplete/ belated/ without

tender cost & earnest money, will not be entertained. The tenderers or their representatives (with

authorization letter) may attend the Pre-bid meeting on 19.02.2015 at 11:30 A.M. for any

clarification.

Separate tender documents are invited and approximate tendering cost are given below:

Sl.No. Package No. Tender Document Approximate Cost (Rs. in Lakh)

01. DST-01 Computer & other accessories 100.00

02. DST-02 Electrical 100.00

03. DST-03 Mechanical 100.00

04. DST-04 Civil 100.00

05. DST-05 Electronics 100.00

06. DST-06 Mining & Drilling 30.00

07. DST-07 Metallurgy 40.00

08. DST-08 Physics & Chemistry 10.00

TENDER DOCUMENT

1. TENDER NOTICE – ET – 01/2014-15 Date : 12.02.2015

2. Tender Document for Purchase of Equipment other than available

on DGS&D rates (Computer and other

accessories / Electrical/ Mechanical/ Civil/

Electronics/ Mining & Drilling / Metallurgy/

Physics & Chemistry) separately for each

category (mention the name of any one

package for which the tender is being

quoted).

3. Cost of tender Rs.10,000.00 (In form of D.D.) per package

4. Date of publication of tender on website : 12.02.2015

5. Date & Time of Pre-bid Meeting : 19.02.2015 at 11:30 A.M.

6. Starting Date of submission of bids : 16.02.2015

7. Last date & time of submission of bids : 10.03.2015 upto 2:00 P.M.

8. Further details can be seen and downloaded from the website: www.jharkhand.gov.in see Tenders.

Dear Sir/ Madam,

The Department of Science & Technology, Jharkhand, Ranchi intends to purchase Equipments,

other than those available on DGS&D rates, (Computer and other accessories / Electrical/

Mechanical/ Civil/ Electronics/ Mining & Drilling / Metallurgy/ Physics & Chemistry)

separately for each category (Package mentioned above) for its Government Polytechnics /

Government Women's Polytechnics located in Jharkhand, for which sealed tenders are hereby

invited only from Manufacturers / Dealers as per Terms & Conditions, Specifications/

configurations, format for Technical Bid (along with soft copy of proforma for Technical

Specification) & Financial Bid (along with soft copy of proforma for Financial Bid) and check

lists mentioned below.

The tenderers shall have to furnish the offer in two separate envelops, clearly mentioning

Envelope No.1 “Technical Bid for package no. Equipments” on the envelop and Envelope

No.2 “Financial Bid for package no. Equipments” on the envelop. Both sealed envelopes

must indicate the description of the tender and then both should be placed together in one sealed

cover, indicating “Tender for the Purchase of package no. Equipments” and the date of

opening of “Technical Bid”. The tender must be sealed and bear the stamp of the Manufacturers

/ Dealers on the face of the envelope and outer sealed cover. The technical bid and financial bid

will be opened on two different dates. The technical bid will be opened on due date as mentioned

in the tender document. The financial bid will be opened in respect of only those tenderers whose

documents are found in order and who qualify technically. The requirements of technical bid are

as under:

PLEASE NOTE THE FOLLOWING TERMS AND CONDITIONS:

1. The tender is liable to be rejected without any clarification, if not submitted as per the

terms and conditions. The tender form shall be downloaded from website (www.

Jharkhand.gov.in) of the Department of Science & Technology. The tenderer must submit

DD of Rs. 10,000.00 (Ten thousand rupees) only per tender as tender price in favour of

The Director, Department of Science & Technology, Jharkhand, Payable at Ranchi in a

separate envelope stapled with the envelop of Technical Bid, otherwise their tender will

be rejected, assuming tenderer is not serious and does not intend to participate in tender

process.

2. Suggestions put up in Pre-bid meeting shall be subject to acceptance to the Department of

Science & Technology. Clarification, if any, on the basis of pre-bid meeting will be

uploaded on the website mentioned above.

3. The tender will be opened on scheduled date and time as mentioned above and the

desirous tenderer or their authorized representatives may be present during opening of the

tender, absence of desirous tenderer or their authorized representative will not be a cause

for rejection or non validation of tender process.

4. Tender received after due date and time will not be entertained under any circumstances.

5. Tender should be submitted in binded form in two parts, first part containing Technical

Bid (along with soft copy for proforma of Technical Bid, Tender cost and EMD

enclosed) and second part containing Financial Bid (along with soft copy for proforma of

Financial Bid enclosed) properly sealed in separate envelopes. The envelopes must be

sealed and marked with Technical Bid and Financial Bid. The bigger sealed envelope

containing Financial and Technical Bid envelops is to be sent directly by speed

/registered post or by hand and marked with Item and page number in the tender

documents i.e Technical & Financial Bid should be strictly in chronological order with

indexing (mentioning page number).

6. Name of the manufacturer with complete address should be mentioned against each item

or equipment.

7. Printed condition on tender will not be binding unless separately mentioned and agreed

subsequently by the department. Copies of the terms and conditions, if any, should be

furnished in duplicate.

8. The tender must furnish complete detailed specifications preferably supported by printed

literature of the equipment offered, if available. Incomplete specification will result in

rejection of tender. Complete description of the item quoted should be mentioned.

9. The rate should be FOR to destination inclusive of all Taxes, Excise, Cess and Freight

charges admissible.

10. The supplier will have to install the equipment/software and impart necessary training, if

any, up to satisfaction of Head of the institution and then only agreed payment will be

released. The suppliers are advised to dispatch all materials to the respective Institutes on

their own convenience strictly within stipulated time period described in the tender

document / agreed time as per order placed.

11. The manufacturer registered with the Industries Department, Government of Jharkhand

may be given applicable price preference as per prevailing rules while comparing /

considering with the other suppliers. In order to avail these preferences such tenderer

should furnish a certified copy of valid registration (for concerned tenderer) and

relevant Government circular, for claiming price preference & exemption of tender

cost / EMD.

12. There should be no alteration/corrections/overwriting in the quotation and prices should

be quoted in figures and as well as in words.

13. The tenderer is required to deposit @ 3% of the quoted amount or (Minimum Rs. One

Lakh only) whichever is applicable as EMD per package. EMD should be deposited in

the form of Demand Draft of Nationalized Bank drawn in favor of The Director,

Department of Science & Technology, Jharkhand, Payable at Ranchi and will be

refundable after completion of tender process as under:-

i) To those bidders whom work order has not been issued - within reasonable time of

finalisation of bidding process i.e. selection of vendors.

ii)To those bidders whom work order have been issued - after successful supply and

commissioning.

Tender Received without EMD will be rejected. Requests for relaxing EMD will not be

entertained. EMD by cheque or MO will not be accepted.

Sl No Quoted Amount (Rs.) EMD (3% of quoted amount) or (Minimum Deposit

of Rs. 1,00,000.00) (which ever applicable)

14. Discount, if offered, should be clearly indicated in the tender both in words and figures

against items or on complete bid. In any case, discount offered for making advance

payment against R/R will not be considered.

15. In case of non-acceptance of the tender, the EMD will be refunded to the tenderer in due

course of time which would be reasonable. The EMD will be treated as security deposit

in case of selected tender. EMD/Security deposit will be forfeited in case of breach of

agreement of supply by the tenderer.

16. The order shall stand cancelled and security forfeited-

I. If supplier expresses his inability to execute the order for the quoted items /

Equipments within the validity period mentioned in the tender agreed upon.

II. If the specified equipment is not supplied within the delivery period mentioned in

the order or within the extended permitted period.

III. If the supplier executes only part of order in stipulated period.

17. Any equipment/hardware/software breakdown must be attended within 72 hours during

the warranty period, free of cost without any travelling expenses.

18. Payment will be released only after the delivery, verification of quality, specification and

successful installation, demonstration and training on equipments and softwares (if any)

at Institute / Headquarter level as case may be.

19. Extension in the delivery period may be granted at the discretion of the Principal

Secretary, Department of Science & Technology, Govt. of Jharkhand. The penalty at rate

of 1% per month of the equipment cost which are not supplied will be charged for the

only one time extension in delivery period. Equipment received after the delivery period

mentioned in the order will also be subjected to this penalty.

20. In case of any failure in execution of order, the undersigned reserves the rights to forfeit

the EMD/Security deposit. The undersigned also reserves the right to cancel the order and

forfeit the EMD/Security deposit in case the tenderer fails to adhere strictly to all terms

and conditions of the order.

21. If any kind of defect in equipment / machine or deviations from the specification are

detected and reported, the supplier should replace or rectify the defects free of cost within

15 days from the date of report, failing which the equipments / machines will not be

accepted. The defective equipment will be collected by the supplier at his own cost and

risk. However the Principal Secretary, Department of Science & Technology may ignore

the delay in exceptional deserving and genuine case where the limit of 15 days is not

adhered.

22. The Department of Science & Technology reserves the rights to select entire or the part

items of the particular package on recommendation of the purchase committee.

23. Tender should be valid for One Year from the date of opening of the tender .The price

will be firm without variations of any kind.

24. The Department of Science & Technology, Govt. of Jharkhand reserves the right to

accept the lowest or any tender and also of rejecting all or any tender without assigning

any reason for the same or to split up the items within two or more suppliers for

placement of order.

25. Request for the supply of any other substituted items other than mentioned in the tender,

will not be entertained.

26. In no case, the delivery period should be more than 75 days for all items. The delivery

period given in the order will be the date of receipt of the equipment in the institute and

not the date of dispatch of the equipment by the supplier.

27. Sealed envelope for the tender should be super–scribed as TENDER NOTICE – ET – 01/2014-15

(name of package applies for) and should be addressed to, The Deputy Secretary,

Department of Science & Technology, Jharkhand, Ranchi, Nepal House Doranda -

834002.

28. The successful tenderer will have to execute an Agreement Bond as approved by the

Government of Jharkhand.

29. Latest income tax clearance, VAT Clearance, Service Tax clearance Certificate from the

competent authority should be attached with the Financial bid of the tender. Tender

received without this certificate will be rejected.

30. The minimum guarantee period for equipment supplied by the supplier will have to be

given which should not be less than one year from the date of installation and requisite

training (free of cost). The tenderer will be required to undertake repair / replacement of

defective part at free of cost in the respective institution.

31. The entire dispute with regard to the contract of purchase of equipment etc. will be

subjected to Legal Jurisdiction of Ranchi only.

32. In the event of the Order the manufacturer of the equipment will be required to furnish a

certificate to the effect that they are manufacture of such and such make and whereas

Dealers will have to furnish a certificate issued by the manufacturer certifying that M/s

such & such is their Dealer under brand name equipment, without this certificate tender

will not be accepted.

33. The equipment/machinery calibrated in SI/metric system need to be quoted. The tenderer

will provide the guarantee for sale & service as and when required.

34. Software should be of Academic/ Educational version. The supplier shall have to make

available up-grade free of cost till one year or guarantee period whichever is higher. The

supplier should also quote yearly up-grade charges additional year onward.

35. Performance guarantee of 1% of the ordered amount in terms of Bank guarantee / DD of

Nationalized Bank drawn in favor of The Director, Department of Science &

Technology, Jharkhand, Payable at Ranchi is to be deposited for the guarantee /

warranty period as applicable by successful bidder.

36. Offers for imported item, if any, for which import license has to be arranged, the tenderer

will have to arrange for the import license and in no case it should be left to the officials/

institution head of Department of Science & Technology. The entire imported items will

have to be delivered in the respective institute by supplier and payment will be made in

rupees only.

37. The company should have the following conditions:

I. Average turnover of Rs. 30.00 crore (Rs. Thirty crores) only in supplying

Equipments in last three consecutive Financial Years i.e. 2011-12, 2012-13, and

2013-14 (Turnover of 03 years / 3).

II. Audit Balance Sheet for last three Financial Years i.e. 2011-12, 2012-13, and

2013-14.

III. Income Tax return in name of organisation / firm for the last three Financial

Years i.e. 2011-12, 2012-13, and 2013-14.

IV. Company TAN No. and or TIN No

V. Company PAN No..

and the supplier should have the experience of supplying material to the Government

Sector for last five years i.e. 2009-10, 2010-11, 2011-12, 2012-13, and 2013-14 and also

the performance certificate of the customers for last successive three years.

38. The tenderer should be an ISO 9001-2008 or latest or applicable certifying body; certified

firm.

39. The tenderer should submit Manufacturer issued Dealership certificate if he is dealer and

in case Manufacturer himself is bidding he should enclose proof of being manufacturer.

40. The tenderer should bear all the transportation & insurance risk till the delivery point.

41. Valid Exemption certificate from Tender Cost and or EMD should be enclosed, if

applicable, along with relevant Government circular, for claiming price preference &

exemption of tender cost / EMD.. Any matter of Exemption will not be entertained after

last date of submission of tender.

42. The tenderer will have to quote tender in the same format and serial order as in the

Tender Document without modifying /tempering the specifications mentioned therein,

however for sake of clarity if he wishes to mention further add-on specification, he can

mention in separate column.

43. Separate purchase orders will be issued by the institutions / headquarters as per their

approved / vetted lists and all financial transactions pertaining to purchase order to supply

and release of fund will be done by concerned institutions / office(s).

44. Intimation about supply of equipments / items by the successful bidders to whom supply

orders have been placed by respective offices, has to be made to the Dept. of Science &

Technology, headquarters.

45. Dept of Science & Technology will have right to add / alter any terms and conditions as

per existing financial/ treasury rules and provisions applicable in the Jharkhand state if it

has not been included/ addressed in the terms and conditions mentioned above. Each and

every page of completed Tender documents are to be signed with seal by authorized

person of manufacturer or dealer.

46. Check List for Technical Bid

Sl No. Item Vendor to Indicate

1. Exemption certificate from Tender Cost and or EMD If applicable (enclose valid

certificate) 2. Tender cost Amount (Rs.) DD No.

3. Quoted Amount Amount (Rs.)

4. Amount Submitted as EMD (3 % of quoted amount) or min. one Lakh rupees only.

Amount (Rs.) DD No.

5. Turnover for years 2011-12, 2012-13, 2013-14. 2011-12 2012-13 2013-14

Amt(Cr) Amt(Cr) Amt(Cr)

6. Average Turn Over (Minimum Rs. Thirty Crore) Amount (Cr)

7. Manufacture registered with the Department of

Industries, Jharkhand for exemption (If Applicable)

Enclose the certified copy of registration

8. ISO 9001-2008 / applicable certified firm Enclose the certificate

9. Certificate of Manufacturer or Dealer (which ever Applicable)

Enclose the certificate

10. Income tax return in name of organization for last three financial year i.e 2011-12, 2012-13, 2013-14.

Mention the Years and enclose certificate

11. VAT Clearance Certificate for year 2013-14 Enclose the certificate

12. Service Tax Clearance Certificate 2013-14 Enclose the certificate

13. Companies valid Registration No. Enclose the certificate

14. Audit balance sheet for last three financial year i.e 2011-12,

2012-13, 2013-14. Mention the Years and enclose

certificate

15. Registration details of Manufacturer or Dealership Enclose relevant certificate

16. Performance Certificate of customer for last three successive years i.e. 2011-12, 2012-13, 2013-14.

Mention the Years and enclose certificate

17. Experience of supplying material to the Government

Sector for last five years.

Mention the Years and enclose Documents

18. Companies TAN & TIN No. Mention the Numbers & enclose

certificates

19. Companies PAN No. Mention the Number & enclose

certificate

20. Soft Copy of Technical Bid filled in Proforma along with Technical Bid

Yes/No

21. Soft Copy of Financial Bid filled in Proforma along with Financial Bid

Yes/No

22. Whether price quoted are inclusive of taxes, duties, Installation & Commissioning and Training (if necessary) for F.O.R. destination?

Yes/No

23. Whether agree to submit Bank guarantee/ DD during warranty period, as required?

Yes/No

24. Whether agree to supply material not more than the rates given to other Govt. Institutions during same financial year?

Enclose in the form of Certificate

25. Whether on-site warranty and training (if any) on the quoted item acceptable?

Yes/No

26. Tenderer should bear all the transportation & insurance risk till the delivery point and commissioning.

Yes/No

27. Whether jurisdiction of Courts in Ranchi acceptable? Yes/No

28. Undertaking with Signature & Seal Yes/No

Note:- (i) Check-list should be properly filled along with Technical Bid in chronological order in

binding with indexing (mentioning page numbers) indicating deviation, if any, signed

by authorized person with seal of company and returned along with offer.

(ii) All documents submitted are to be self attested and duly stamped. A list of documents

being submitted shall be prepared and enclosed with the order (paging).

Date:_______________ Signature & seal of the Vendor.

47. Proforma for Technical Specification

The offer should be submitted in the following format only

Sl No Name of the Item along with make

Specifications given in tender

Technical specifications which the bidder wants to supply as

per catalogue brochure Remark

Note : Attach catalogue/ brochure in original for above quoted items. The quoted items should

conform to Bureau of Indian Standard. (Soft copy of above Technical Specification

required)

48. Proforma for Financial Bid

The offer should be submitted in the following format only

Sl No

Name of the Item along with

make

Specifications given in tender

Technical specifications which the bidder wants to supply as per catalogue brochure

Discount (if applicable)

Discounted Price of Equipment inclusive of all Taxes & all other Charges

Remark

Note : All the above quoted items rate should be in confirmation with the tender conditions.

(Soft copy of above proforma for Financial Bid required)

49. Undertaking

(To be signed and returned along with the tender)

I/We (Full Name) …………………………………………………………………………

Address ……………………………. have gone through the tender rules for the supply of

various stores as per TENDER NOTICE –ET – 01/2014-15) (Purchase of Equipment

i.e. Name of respective Package applied for) of The Department of Science &

Technology, Jharkhand, Nepal House, Doranda, Ranchi – 834002 and I/We fully accept

the bidding Terms and conditions available with bidding documents.

Date……………………..

Signature

(Name & Full Address of the Firm)

(Dr. Arun Kumar)

Department of Science & Technology,

Jharkhand, Ranchi.

DST-01- List of Computer branch equipments

Sl. No. Name of Equipment Specification

1. Personal Computer (Desktop) CPU - Intel i7 3770 3.4 GHz or more

processor

Memory RAM DDR3 - 8GB,

Intel Q77 Mb

HDD - 1 TB

TFT / LED Monitor 15.6"

Optical Mouse, Keyboard

combo drive .,

Preloaded windows 8.1

2. Softwares:

C, C++ Compiler (Turbo C3)

Microsoft office 2007, UNIX,

DotNET, XML,

Anti Virus- Quick Heal

All latest version

3. Server: CPU - Intel Xeon processor quad core

Memory RAM DDR3- 16GB,

HDD - 1 TB dual

TFT / LED Monitor 18.5"

optical Mouse, Keyboard

combo drive

Switch - 48 port

CAT - 6 cable

RJ 45 Connectors

Or latest version

4. Softwares: Oracle 12 ver. or higher

Visual Studio, NMS s/w,

Linux Red Hat, Appache Tomcat, IIS,

All latest academic version

Dreamweaver, XAMPP

5. Softwares: AutoCAD 14, STADD,

Matlab, CATIA

MySQL, JDK, Adobe suite, Scilab,

Rational Rose (IBM),

3D Max

All latest academic version

6. Projector Multimedia projector with minimum of these:

lamp intensity of 3000 lumens, 5000h, 1200 x

1080 res. and compatible connectivity to PC,

with recording facility.

7. Digital camera/ handycam Minimum of these functions are required: Still

and recording options, 16 Megapixels, 5x

optical zoom, built-in recording system,

option of connectivity to PC, software for film

editing and audio mixing.

8. External drive 1-4 TB, SATA

9. Lighting system Quad optical illumination system with

10. Printer - Color (Laser) A3 size, 24ppm B/W, 16 ppm coloured, with

memory, built-in processor and USB

connectivity to computer

11. Scanner A4 size, 2000 dpi, flat bed,

12. Online/ Offline UPS with branded

proper batteries.

3KVA, 5KVA, 10KVA with 120 min backup,

switch over time in msec.

DST-02- List of Electrical Equipments

1 1-ph Transformer trainer kit to perform

following experiments:

-Study of Transformation Ratio in a

Single Phase Transformer

-Study of Polarity Test in a Single Phase

Transformer

-Study of Open Circuit Test in a Single

Phase Transformer

-Study of Short Circuit Test in a Single

Phase Transformer

-Study of Load Test and correspondingly

determine the efficiency and Voltage

Regulation in a Single Phase

Transformer

Mains Supply : Single Phase, 230V AC

±10%, 50Hz


Rating : 1kVA

Primary Voltage : 0-125V, 0-125V

Secondary Voltage : 0-125V, 0-125V

Rated Current : 5A

Single Phase Auto Transformer

Primary Voltage : 230V

Secondary Voltage : 0-270V

Rated Current : 5A

Analog Meters Used

Voltmeter (MI) : 300V (2 Nos.)

Voltmeter (MI) : 50V

Ammeter (MI) : 5A (2 Nos.)

Ammeter (MI) : 1A

Wattmeter : 100W

Wattmeter : 1000W

2 AC Motor Starters-DOL Starter,

autotransformer starter and star-delta

starter suitable for 3 H.p. Induction

motor

AC Motor Starters-DOL Starter,



motor

3 All Starter trainer For DC Motors- (i) Three point starter

suitable for 5 H. p. motor (ii) Four point

starter suitable for 5 H.p. motor

(iii) Series motor starter suitable for 5

H.p. motor

AC Motors- DOL Starter,



motor

4 Auto Transformer- 2KVA, 3-Phase, input- 415v, output- 0-

415v

5 Current Transformer

(For Laboratory purpose)

Potential Transformer

(For Laboratory purpose)

Current Transformer-

Burden 10 VA, 20:5 A

Potential Transformer

Burden 10VA, 230:23V

6 D.C. Motor starters

(i) Three point starter suitable for 5 H. p.

motor (ii) Four point starter suitable for

5 H.p. motor


H.p. motor

D.C. Motor starters

(i) Three point starter suitable for 5 H. p.

motor (ii) Four point starter suitable for

5 H.p. motor


H.p. motor

7 DC Motor Trainer kit for both Shunt and

Series motor to perform following

experiments:

-Study of No Load Characteristics of DC

Shunt Motor

-Study of Load Characteristics of

Separately Excited DC Generator

-Study of Speed Control of DC Shunt

Motor by Field current control and

Armature voltage control methods


Separately Excited DC Motor

-Study of Self Excited DC Shunt Motor

-Speed Control of DC Shunt Motor by

Field Current and Armature Voltage

Control

-Load Characteristics of DC Shunt Motor

-N-I Characteristics of DC Shunt Motor

-N-V Characteristics of DC Shunt Motor

-Study of self excited DC Shunt Motor

Type : Shunt

Rating : 1 HP

Voltage Rating : 180V/200V

Speed : 1500 RPM

Type : Series

Rating : 1HP

Voltage rating : 200V

Speed : 1500 RPM

-Study of Operating Characteristics of DC

Series Motor

-Study of Speed Control of DC Series

Motor using Field Current Control

-Study of Speed Control of DC Series

Motor using Armature Voltage

Control

8 Electrical Circuit Lab Trainer kit to

perform following experiments-

1) Study and verification of Ohm’s Law

2) Study and verification of Kirchhoff’s

current & voltage law

3) Study and verification of Norton's

theorem

4) Study and verification of Thevenin's

Theorem

5) Study and verification of Maximum

Power Transfer Theorem

6) Study and verification of

Superposition theorem

7) Study and verification of Reciprocity

theorem

Electrical Circuit Lab Trainer kit to

perform following experiments-

1) Study and verification of Ohm’s Law

2) Study and verification of Kirchhoff’s

current & voltage law

3) Study and verification of Norton's

theorem

4) Study and verification of Thevenin's

Theorem

5) Study and verification of Maximum

Power Transfer Theorem

6) Study and verification of

Superposition theorem

7) Study and verification of Reciprocity

theorem

9 Electrical Lab Trainer Kit with built-in

meters for measurements to perform


1) To study the Resistances individually

as well as in series and in parallel

connections

2) To study the Ohm's Law

mathematical relationship between

three

variable Voltage (V), Current (I) and

Electrical Lab Trainer Kit to perform


1) To study the Resistances individually

as well as in series and in parallel

connections

2) To study the Ohm's Law

mathematical relationship between

three

variable Voltage (V), Current (I) and

Resistance (R)

Resistance (R)

3) To study the voltage and current

flowing into the circuit

4) To study the Kirchhoff's Law for

electrical circuits

5) To study the R-C circuit and find out

the behavior of capacitors in a R-C

network and study the phase shift due to

capacitor

6) To study the L-C circuit and find out

its behavior as resonance circuit

7) To understand the Faraday's Law of

electromagnetic induction

8) To study the phenomenon of mutual

induction

9) To study the Lenz's Law and effect of

Eddy current

10) To convert a Galvanometer into Volt

meter

11) To convert a Galvanometer into

Ammeter

12) To construct and study a step down

transformer with the help of given coils

and cores

13) To construct and study a step up

transformer

14) To study the effects of moving I core

on a step up transformer

15) To study the hysteresis curve

3) To study the voltage and current

flowing into the circuit

4) To study the Kirchhoff's Law for

electrical circuits

5) To study the R-C circuit and find out

the behavior of capacitors in a R-C

network and study the phase shift due to

capacitor

6) To study the L-C circuit and find out

its behavior as resonance circuit

7) To understand the Faraday's Law of

electromagnetic induction

8) To study the phenomenon of mutual

induction

9) To study the Lenz's Law and effect of

Eddy current

10) To convert a Galvanometer into Volt

meter

11) To convert a Galvanometer into

Ammeter

12) To construct and study a step down

transformer with the help of given coils

and cores

13) To construct and study a step up

transformer

14) To study the effects of moving I core

on a step up transformer

15) To study the hysteresis curve

10 Electrical Testing Kit –

1.Digital Multimeter,

2. Clamp meter,

3. Non Contact Voltage Detector,

Multimeter- Range- 3½ Digit

DC-AC Volts & Currents

Resistance / Diode / Continuity Testing

Capacitance /frequency/ Measurement

4. AC Circuit Breaker Finder/Receptacle Tester

Transistor HFE Measurement

10A Range Fuse Protected

Auto Polarity

Over Range indication

2. Clamp meter- 3½ digits LCD with a

Max. reading of 1999, AC current Range-

600A, DC/AC Voltage- 600v Resistance-

2Mohms

3. Non Contact Voltage Detector- Pen

type, 90-1000 V

4. AC Circuit Breaker Finder /

Receptacle Tester- Suitable for 230 Volts

11 Induction Motor Generator Set Induction Motor

Type : 3-Phase, Slip ring

Rating : 2HP

Voltage Rating : 415V

Speed : 1500 RPM

Three Phase Synchronous Machine

Type : Salient Pole

Rating : 1KVA

Voltage rating : 415V AC

Speed : 1500 RPM

Excitation Voltage : 120V

12 Infrared Tachometer Non Contact type, 5 digit LCD display

13 M.G. Set- D.C.Machine driven

Synchronous Machine Trainer kit to

perform following experiments:

-Synchronization of two Three Phase

Alternators by

DC Machine

Type : Shunt


Rating : 2 HP

a) Synchronoscope method

b) Three dark lamp method

c) Two bright one dark lamp method

-Regulation of Three Phase Alternator by

a) Open Circuit test

b) Short Circuit test

-Study & Analysis of V-Curve & Inverse

V-Curve of Synchronous Motor

Speed : 1500 RPM

Three Phase Synchronous Machine

Type : Salient Pole

Rating : 1KVA

Voltage rating : 415V AC

Speed : 1500 RPM


14 Model of 3 phase, 1.5 Hp Submersible

pump for laboratory pupose

3Ph, 415V, 1.5Hp

15 Oil immersed Power Transformer with

all safety devices such as conservator,

breather, Buchholz relay etc.

5KVA, 3 phase, 415V/ 230V, 50 Hz

16 Position control AC and DC Servomotor

(for laboratory purpose)

Position control AC and DC Servomotor

(for laboratory purpose) with step size

of 1.5 deg

17 Resistor Load Bank Three phase, 2KW, 415V

18 Rheostat Set :- Each set consists 2000

Ohms, 1 A, 500 Ohm, 2A, 150Ohms, 2A,

40Ohms, 5A, 20Ohms, 5A.

Rheostat Set :- Each set consists 2000

Ohms, 1 A, 500 Ohm, 2A, 150Ohms, 2A,

40Ohms, 5A, 20Ohms, 5A.

19 Shunt Motor- DC Machine Trainer kit to


-Study of No Load Characteristics of DC

Shunt Motor


Separately Excited DC Generator

-Study of Speed Control of DC Shunt

Motor by Field current control and

Armature voltage control methods


Separately Excited DC Motor

-Study of Self Excited DC Shunt Motor

-Speed Control of DC Shunt Motor by

Field Current and Armature Voltage

Type : Shunt

Rating : 1 HP

Voltage Rating : 180V/200V

Speed : 1500 RPM

Control

-Load Characteristics of DC Shunt Motor

-N-I Characteristics of DC Shunt Motor

-N-V Characteristics of DC Shunt Motor

-Study of self excited DC Shunt Motor

20 Single Phase Induction Motor Trainer kit

to perform following experiments:

-Study of Single Phase Induction Motor

-Study of Running and Reversing of

Single Phase Induction Motor

-Study of the No-Load Test in a Single

Phase Induction Motor

-Study of the Blocked Rotor Test in a

Single Phase Induction Motor

-Study of Load Test of a Single Phase

Induction Motor

Type : Capacitor start

Rating : 1HP

Voltage rating : 230V ±10%

Speed : 1440 RPM

21 Solid State controlled Bridge Rectifier-

1Ph with measuring meters

1Ph, 50Hz, 2KVA, 220V

22 Solid State controlled Bridge Rectifier-

3Ph with measuring meters

1KVA, 415V, 3 phase, 50Hz

23 1-Phase to 3-Phase Converter 1.5Hp/1.1Kw, Single Phase to 3-Phase,

230v to 415v

24 Synchronous Motor Trainer kit to


-To study the Inverse V curve of the

Three Phase Synchronous Motor

-To study the V curve of Three Phase

Synchronous Motor

Three Phase Synchronous Motor

Type : Salient Pole

Rating : 3 HP

Voltage rating : 415V ±10%

Speed : 1500 RPM


With DC Machine (Acts as generator for

Excitation)

Type : Shunt

Rating : 2 HP


Speed : 1500 RPM

25 Three Phase Induction Motor Trainer kit

to perform following experiments:


Three Phase Induction Motor

-Study of No Load Test performed in a


-Study of Block Rotor Test performed in

a Three Phase Induction Motor

-Measurement of Slip in a Three Phase

Induction Motor

-Study of Speed-Torque characteristics

in a Three Phase Induction Motor

Type : Squirrel Cage

Rating : 1HP


Speed : 1440 RPM

Load and Pulley arrangement.

DOL Starter, autotransformer starter

and star-delta starter.

Single phase preventer and over-current

relay.

26 Three Phase Slip Ring Induction Motor

Trainer kit to perform following

experiments:



-Study of No Load Test performed in a


-Study of Block Rotor Test performed in

a Three Phase Induction Motor

-Measurement of Slip in a Three Phase

Induction Motor

-Study of Speed-Torque characteristics

in a Three Phase Induction Motor

Type : Slip ring

Rating : 1HP


Speed : 1440 RPM

27 Transformer- 1KVA, 1 Phase, 50Hz, 230V/ 115V,

Secondary tappings at 5%, 50% and

86.6%

28 Transformer - 1 KVA, 1 Phase, 50 Hz, 230/115V, Shell

Type Mounted

on a wooden Platform

29 Transformer- 3-ph Transformer trainer

kit to perform following experiments:

-Study of Three Phase Configurations

-Study of Open Circuit Test in a Three

Phase Transformer

-Study of Short Circuit Test in a Three

Phase Transformer



Regulation in a Three Phase

Transformer

Type : Three Phase

Power Rating : 1kVA


Secondary Voltage : 230V

Rated Current : 4A

30 Transformer Experimenter- Single phase

Transformer trainer kit to perform


-Study of Transformation Ratio in a


-Study of Polarity Test in a Single Phase

Transformer

-Study of Open Circuit Test in a Single

Phase Transformer

-Study of Short Circuit Test in a Single

Phase Transformer



Regulation in a Single Phase

Transformer

Mains Supply : Single Phase, 230V AC

±10%, 50Hz


Rating : 1kVA

Primary Voltage : 0-125V, 0-125V

Secondary Voltage : 0-125V, 0-125V

Rated Current : 5A

Single Phase Auto Transformer


Secondary Voltage : 0-270V

Rated Current : 5A

Analog Meters Used

Voltmeter (MI) : 300V (2 Nos.)

Voltmeter (MI) : 50V

Ammeter (MI) : 5A (2 Nos.)

Ammeter (MI) : 1A

Wattmeter : 100W

Wattmeter : 1000W

31 Choke Coil 3Ph, 415V, 2KVA

32 AC Generator coupled to Diesel engine 1Ph, 230V, 5KVA

33 Circuit Breaker Demonstration board Circuit Breaker Demonstration board

with 5A

34 Transmission Line Trainer Transmission Line Trainer with

parameter measurement accessories

35 Electrical Power Distribution Trainer Electrical Power Distribution Trainer

with parameter measurement

accessories

36 Megger Range- Upto 1000MΩ

37 Earth resistance tester Ranges- 0-2Ω, 0-20Ω, 0-200Ω, 0-2kΩ

38 Digital Cable fault locator Digital Cable fault locator with

parameter measurement accessories

39 Oil Insulation test kit Oil Insulation test kit with parameter

measurement accessories

40 Electric Traction Trainer Electric Traction Trainer with parameter

measurement accessories

DST-03- List of Mechanical & Automobile Engg. Equipments


1. Acetylene cylinder

regulator

Suitable for lab purpose

2. Acetylene generator. Suitable for lab purpose

3. Air compressor Air compressor for petrol / diesel car of 1000 cc 4. Angel cutter 2x1/4” Angel cutter 2x1/4”

5. Arc Welding machine.

Welding machine ( electric arc ) with attachments like cable ,electrode holder

etc. needed for performing welding in lab.

6. Auger ½” Auger ½”

7. Ball pen hammer 2 ½

LBS Ball pen hammer 2 ½ LBS

8. Bell crank lever The apparatus consists of the following parts :

(i) A lever of well seasoned wood having horizontal arm 75 cm and vertical arm

20 cm.

(ii) A spring balance of 10kg capacity with adjustable wing nut at shorter end.

(iii) A set of slotted cast iron weights of 0.5 kg with necessary one hanger (four

slotted weights and one hanger of 0.5 kg. Total weight 2.5 kg The complete

arrangement p mounted on steel frame against wall. But without foundation

bolts.

9. Bench Vice 6” Bench Vice 6” for lab purpose

10. Bend Saw m/c 6’ Bend Saw m/c 6’ for lab purpose

11. Bernoulli’s Theorem

Apparatus

System Components:

Centrifugal pump: ½ HP Tully/Reputed make

Constant Head Tank, Sump Tank (70 Ltrs), Measuring tank.

Venture Tube: Inlet and outlet diameter 25mm

Manometer panel consisting of transparent tubes mounted on a graduated

screen of height 400 mm approx.

Pipe and fittings made of PVC/Corrosion resistant plastic

Digital Stop Watch, Piezo-meter, Stand

Operation and Maintenance manual to be provided.

12. Boring

Drill of mm to 15 cm, motorised, extendable depth arm from cm to multiple

meters length

13. Brinell Hardness Loads (kgf) - 500,750,1000,1500,2000,2500,3000

Testing M/c Pre Load (kgf) – NIL Max. Test Height (mm) - 250 Depth of Throat (mm) - 150 Size of Base (mm) - 255 X 495 Machine Height (mm) - 860 STANDARD ACCESSORIES Flat Testing Table ( 50 mm ø) -1 pc Flat Testing Table ( 200 mm ø) -- 1 pc Testing Table (70 mm ø 'V' Grooved) - 1 pc Ball Holder (5 mm) -- 1 pc Ball Holder (10mm) -- 1 pc Brinell Microscope – 1 pc Allen Spanner –2 pc Test Block ( HB - 5/750) Test Block ( HB - 5/750) Instruction Manual -2 books

14. Capstan Lathe with all

accessories.

Specification in mm

Spindle Hollow 62

Maximum Collet Capacity 60

Range of Spindle Speeds 90 - 1000

Effective Strokes of Turret Slide 180

Bore Size in Turret Hex Head 32

Center of Holes above Turret Slide 55

Max. distance between spindlenose to turret face

430

Cross Slide Transverse Travel 150

Cross Slide Longitudinal Travel 300

Length of Bed 1375

Width of Bed 230

Height of Center above Bed STANDARD ACCESSORIES: Suitable Electric 3 phase 440 Volts 50 Cycle with starter and fittings Splash Guard One Collet Bar Stopper Spanner set Coolant Pump with Assembly Vertical Slide Bar Feeding attachment Threading and Cutting attachment Tool Holder True Chuck with Chuck Rate

190

15. Centrifugal pump

model

Cut section model of centrifugal pump for display of various parts and action

16.

Centrifugal pump set

System Components :-

This system incorporates the following components :-

1) Centrifugal pump size – 25.4 mm X 25.4 mm (Approx), Discharge: 15-30 lpm

at 30 meter (Approx), Total head : 12 Meter (Approx).

2) Driving Motor : 1 HP, electric Motor 230V AC, 50 Hz,

3) Pressure Gauge : 0.5 Kg / Sq. cm

4) Vacuum Gauge : 760 mm (Approx)

5) Foot Valve size : 25.4 mm (Approx) Plastic

6) Gate Valve size : 25.4 mm (Approx) Plastic

7) Variable speed arrangement by reduction pulley: 3 Step cone pulley.

8) Energy meter.

9) Stand: M.S. Structure with powder coating.

10) Measuring Tank : 40 Liter non-corrosive PVC tank

11) Mechanical level measurement facility with scale.

12) stop Watch

13) Piping & fittings & Valves.

14) Flow Measurement facility.

Operation & maintenance manual will be provided.

17. Centrifugal Pump Test

Rig.

System Components:

This system incorporates the following components:

1- Centrifugal pump size- 25.4 mm X 25.4 mm (Approx) Discharge: 15-30 lpm at 30 meter (Approx), Total head: 12 Meter(Approx).

2- Driving Motor: 1 HP, electric Motor 230 V AC. 50 Hz. 3- Pressure Gauge : 05.kg/Sq. cm 4- Vacuum Gauge: 760 mm (Approx) 5- Foot Valve size: 25.4 mm (Approx) Plastic 6- Gate Valve size : 25.4 mm (Approx) Plastic 7- Variable speed arrangement by reduction pulley: 3 Step cone pulley. 8- Energy meter. 9- Stand: M.S. Structure with powder coating. 10- Measuring Tank: 40 Liter non-corrosive PVC tank. 11- Mechanical level measurement facility with scale. 12- Stop Watch. 13- Piping & fittings & Valves. 14- Flow Measurement facility. 15- Operation maintenance manual will be provided.

18. Circular cutting

machine.

Suitable for lab purpose

19. Circular Saw m/c 4’x4’

Circular Saw m/c 4’x4’ for lab purpose

20.

CNC lathe trainer kits

with simulation

software.

CNC Trainer Lathe Machine Suited for educational purposes and is fully in line

with industrial standards in terms of design and functionality. All essential

process in modern manufacturing can be explained and under stood in a

manner that reflects authentic practice. A few sensible simplifications, an easily

understood machine design and ease of operation mean that students can learn

rapidly and reliable with simulation software.

Brief

CNC lathe with professional software

Under table cabinet for CNC lathe.

Accessories.

Set to tools with materials, Set of cutting edges.

Media

Manual CIM1: Commissioning a Lathe.

Optional accessories:

Automation set for CNC lathe.

Set of allen keys, Vernier caliper

Lathe machine programming software with 3D simulation.

Other features:

Compact CNC lathe Hardened cost bed in line with industrial machinery Professional software with simulation of operating procedures Machine safety cabin High-resolution axis motors Clockwise/anti clockwise spindle rotation Continuously controllable main drive Automatic 8 way tool bit changer.

21.

CNC milling m/c with

all accessories &

simulation software.

Drilling Capacity : 10mm (3/8”)

Worktable Size : 400x145mm (16” x 5.7”)

Worktable T-Slot Size : 8mm (0.31”)

No. of T-Slot on Table : 3

Max. Loading of Worktable : 20 kg

Table Travel x axes : 260mm (10”)

Table Travel y axes : 110mm (4.3”)

Table Travel z axes : 180mm (7”)

X Axes Feeding Motor Power : 1.35Nm

Y Axes Feeding Motor Power : 1.35Nm

Z Axes Feeding Motor Power : 2.2Nm

X/ Y/ Z Axes Max. Moving Speed : 2m/min

X/ Y/ Z Axes Feeding Speed : 500mm/min

Throat : 150mm (5.9”)

Position Precision : 0.015mm

Repeat Positioning Precision : 001mm

Spindle Taper : MT2#/

Spindle Speed : 100-7000rpm

Spindle Motor : 500w

Simulation software & operation manual

22. Complete Foundry

tool kit equipment.

Foundry tool kit containing tools used in moulding & casting process.

23.

Composite wall

apparatus

1) Slab : 150mm dia., 6mm thick 2) Slab material : MS, Brass & Asbestos 3) Water tank : SS tank with powder coat (3 liters) 4) Measuring Jar : Plastic-250ml 5) Stop watch :Digital 6) Heater : 75mm dia. Mica-250 watts

7) Voltmeter : Digital voltmeter of range 0-300V AC 8) Ammeter : Digital ammeter of range 0-200A AC 9) Temperature Indicator : Digital Temperature Indicator of range 0-400 degree Celsius with TSS 10) Thermocouple :Teflon coated Cr-Al (K-type) -14 no 11) Variac :Electronic Dimmer 1.5 kw Self explanatory operating manual containing brief theory and practical exercises and a set of sample calculation report.

24. Compression Testing

Machine for Green

Strength of Moulding

Sand.

To determine Compression strength of Green sand in lab ,with spring balance(0-2500gm/cm2)&tray .

25. Cope & Drag Patterns

with core prints of

various sizes and

shapes (wood made)

model for lab demonstration purpose

26. Crank shaft grinder

Maximum distance between centres : 1500mm Maximum distance between chuchks: 1400mm Max.weight of shaft to be handled : 120kg Swing over table : 500mm Maximum Stroke :225mm Height of centre above table : 262.5mm Work head spindle speeds : 27-41-61 rpm Grinding wheel speeds : 950rpm Table traverse rapid/rev : 10mm Wheel head feed rapid/rev : 12.5mm Wheel head feed slow/rev : 0.25mm Tail stock quill travel : 87mm Wheel head motor :5hp Work head motor :1hp Coolant pump motor :0.1hp Manual & necessary accessories.

27. Creep Testing M/C [1] Table unit for the investigation of the creep behaviour of different materials

[2] Specimen cross-section 2x5mm, measured length 25mm

[3] Tensile stress range 5...25N/mm²

[4] Position measurement gauge 0...10mm, resolution 0.01mm

[5] Experiments above or below room temperature possible with conditioning

box

28. Cupola furnace Cupola furnace

29. Cut section model

mechanical break

system.

Cut section model mechanical break system.

30. Cut section model of 2

stroke single cylinder Cut section model of 2 stroke single cylinder

31. Cut Section model of 4

stroke single cylinder

engine.

Cut Section model of 4 stroke single cylinder engine.

32. Cut section model of

steering gear box. Cut section model of steering gear box.

33. Cut Section of 4

wheeler & 2 wheeler.

Cut Section of 4 wheeler & 2 wheeler.

34. Cylinder Reba ring

machine

Cylinder Reba ring machine

35. Diesel fuel pump test

bench

Diesel fuelpump test bench with 7.5 H.P. Electric Motor. Gives Variable transmission through A.C. Frequency Drive equip-ted with Electronic Control Panel. R.P.M., Strokes and Temperature on LED Display with C.P.U. The R.P.M of machine are from o to 4000. The Inline Pump and Rotary pump transfer pressure display on digital pressure gauges. Swiveling injector console with heavy duty jack system works for R.H.S. and L.H.S. F.I.P. Pumps. An inbuilt compressor is also provided for air boost pressure. this machine enables for testing inline pumps rotary pumps (mechanical, electronic diesel control pumps (E.D.C.)) and C.R.D.I pumps injector and common rail.

36. DIESEL FULL SET

DOUBLE FLY WHEEL

10HP , RPM 1000

37. DRILLING MACHINE

(RADIAL):

Drilling Capacity: 25mm, Pillar Dia: 127 mm, Spindle Nose: MT-3, Dist From

spindle to pillar surface: 620mm, Spindle Travel: 200mm, No. of Spindle Speed:

8, Spindle Speed (RPM) : 110-2880, Base to Spindle , Nose: 810 mm, Drilling

Motor : 1&0.5 H.P.

38.

Drilling machine with

set

DRILLING MACHINE (PILLAR) :

Drilling Capacity : 40 mm, Pillar Dia : 130mm, Spindle Nose : MT-4, Spindle

Travel : 215mm, Spindle Center to Pillar Surface : 305mm, No. of Spindle Speed

: 8, Spindle Speed (RPM) : 70-2070, Base to Spindle Nose: 1040mm, Electric

Motor: 1.5 H.P.

39. Electric Arc furnace Electric Arc furnace

40. Electrical Equipment

board of a car

Electrical Equipment board of a 1000 cc car

41.

Electrode oven

1. Double walled stainless steel interior

2. The interior is provided with epoxy powder coated

3. Mild Steel exterior

4. Glasswool & Puff Insulation negate temperature loss

5. Chamber illumination for viewing sample

6. Full length inner plexi-glass door

7. Castor wheel arrangement for easy mobility

8. Digital Temperature Controller

9. Provided with dry bulb and wet bulb principle

10. Hermetically sealed Kirloskar compressor

11. Air cooled condensing unit and accessories

12. Durable SS tubular heaters

42. Fatigue Testing M/C 1) Benchtop unit for fatigue strength testing 2) Special shape specimens for demonstrating the influence of

notching and surface finish 3) Recording of a stress-number (S-N) diagram

4) Motor speed 2800rpm, power output 0.37kW

5) Single phase electric motor, 230V , 50Hz

6) Loading with spring balance 0...300N

7) Adjustment using threaded spindle with hand wheel

8) Loading via moveable plain bearing

9) Automatic shut down on specimen fracture by stop switch

integrated into the bearing

10) Electronic load cycle and revolutions counter with 8-digit digital

display

43. Firmer Chisel 1 ½ Firmer Chisel 1 ½

44. Flexible shaft grinder.

Flexible Shaft Grinder 2 Speed, Dimension: 230 mm x 405 mm, Wattage: 370 W Dimension 230 mm x 405 mm Collet Diameter: 6 mm, Flexible Shaft length: 1360 mm

45. Four Cylinder Four

Stroke Petrol Engine

Test Rig.

Specification: Engine: Four Stroke four Cylinder petrol engine of 1100 CC

developing about 10 HP at 2000 RPM.

Dynamometer: The Engine is coupled to Hydraulic brake

Dynamometer of capacity 10 HP at 2000 RPM

Fuel Measurement: Fuel tank mounted on sturdy iron stand, burette tube, three

way cock, connecting tubes & a stop clock.

Air Intake Measurement: Air intake reservoir of size 0.4m X 0.4m X 0.7m with

orifice plate. U-Tube manometer of 0.5 height for measurement of air.

Cooling Arrangement: Cooling water measurement by Rotameter to determine

the discharge of cooling water. Test rig needs enternal cooling water supply

system.

Calorimeter: Shell and Tube Heat Exchanger to measure that heat goes through

exhaust gases.

Following Accessories are provided with Test Rig: An ignition switch, a self

Starter, battery ammeter, a throttle (Accelerator) control, Special arrangements

by switches for cutting of ignition of each cylinder for MORES TEST all

instruments mounted on a suitable panel board.

12 channel Digital Temperature indicator with thermocouples.

46. Four Cylinder Four

Stroke Water Cooled

Diesel Engine test rig.

Type of Engine: Four Cylinder, Four stroke engine, Vertical water cooled, self

start, diesel engine. Type of Loading: Hydraulic Brake Dynamometer/Eddy

Current Dynamometer Fuel measuring system: Fuel measuring system consists

of a fuel tank, a burette and a three way cock arrangement. Air intake

measuring system: Air tank fitted with orifice and water manometer.

Measurement of Heat carried away by cooling water: Meter and temperature

Indicator with multi-channel switch Temperature sensors: RTD PT-100 type

Electric Supply: Single Phase 220 V.5 Amps Continuous water supply: 10 LPM

approx, Fuel: 20 ltrs (Diesel) Tachometer: For RPM measurement, Battery: 12

Volt 88 Amp.

47. Four fold boot rule

24” Four fold boot rule 24”

48. Francis Turbine model model for lab demonstration purpose

49. FRICTION LESS

HEADLESS PUMP SET

5 HP

FRICTION LESS HEADLESS PUMP SET 5 HP

50. Friction slide

apparatus.

i) One set of three wooden carriages with different bottom surface (Wood , glass and iron) (ii) One carriage with frictionless rollers (iii) One set of three different surfaces for friction board –a glass plate, a plywood and felt cloth. Normal Quality: Simple type having a wooden board 75 x 15 cm. with glass surface, a frictionless pulley is fixed to one end, four sliding blocks of different area are provided to determine the force of friction, with scale pan but without weights.

51. Gamma ray

radiography testing

M/C.

Gamma ray radiography testing M/C. to demonstrate non- destructive test in

lab

52.

Gas cutting torch with

set.

Cutting Capacity : 5 mm to 70 mm. Bevels : 0 to 45 degrees . Straight Cuts : 1.8 meters and multiples. Circle Cutting : 75 mm dia to 1200 mm dia. Cutting Speed : 80 mm/min to 800 mm/min [variable] Torch Adjustment : Vertical-70 mm Horizontal-85 mm Voltage : 220/250 Volts, AC/DC,50 Hz. Maximum Current : 0.35 Amperes.

53.

Gas Welding m/c.

Oxygen cylinder (HP0 with key

Acetylene cylinder (HP)

Oxygen regulator (HP)

Acetylene regulator (HP)

Oxygen hose pipe 10m

Acetylene hose pipe 10m

Welding torch

Cutting torch

Welding nozzle 0 to 12

Cutting nozzle 1/8, 1/16, 1/32, 3/16, 5/64, 3/32

Goggles

Sparking lighter

54. Grinding machine Cylindrical Grinding machine with all standard accessories of Standard make with the following specifications: Centre hdight-125mm; Between centers 600mm:max grinding length 400mm:Table speed 01 to 5 mts/min Universal; Max travel 400mm:min automatic travel 2.5mm ; Max swivel of table 30 deg. Rapid approach-40mm; Infeed with hand wheel-20mm; max plug depth on dia 1.7 mm; Power 4.5 to 5 KW; Grinding speed 30/45 mt/min.;

Spindle speeds -8 steps; min accuracy .002 mm; Cylindercity over 400 mm os max of .002 mm

55.

Hand shearing

machine.

Blade Length (mm) : 200 Max . Cut in One Stroke (mm) : 150 Plate / Sheet ( MS) mm : 3 Flat (mm) : 50 x 5,Round (mm) : 10 Including safety items & instruction manual .

56. Head grinder

Segmental wheel dia : 300mm Segmental wheel : 1400rpm Working surface of table max. (mm) : 1220x290 Height from table to wheel max. : 600 mm Table travel : 1100 mm Grinding capacity (m) : 900 x 280 Table speeds per minute : 6' x 8' x 12' Vertical micro feed graduation : 0.01mm Table with t-slot to take bolt : 13mm Centre to (t slot) : 14.5mm Grinding wheel motor : 7.5hp Feed motor for main slide : 1.5hp Coolant pump motor : 0.1hp Rapid motor for ram : 1hp Magnetic chuck size (mm) : 755 x 250

57.

Heat Transfer lab

equipment in forced

convection.

Equipment objective is to determine Heat Transfer Coefficient and the rate of Heat Transfer by Forced Convection for flow of air inside a horizontal pipe. 1) Test section : Copper tube of 25 mm Id, 32mm Od and 400mm long (Stainless steel or Brass) 2) Manometer : U –tube with mercury as working fluid 3) Blower : Centrifugal 1/2 Hp, 220 V ac 4) Heater : Externally heated , Nichrome band type (250watt) 5) Voltmeter : Digital voltmeter of range 0-300V AC 6) Ammeter : Digital ammeter of range 0-5A AC 7) Temperature Indicator : Digital Temperature Indicator of range 0-400 degree Celsius with TSS 8) Thermocouple :Teflon coated Cr-Al (K-type) -7 nos 9) Variac :Electronic Dimmer 1.5 kw Self explanatory operating manual containing brief theory and practical exercises and a set of sample calculation report.

58. Hydraulic Bench with

all accessories.

Hydraulic Bench with all accessories.

59. Hydraulic Ram Hydraulic Ram

60. Hydraulics prototype

working models with

standard specification

Hydraulics prototype working models for lab purpose

61. Impact Testing M/c 1. Caliper gauge for checking V notch for Ioad & Charpy as per BS:131 :PART 1, 2, 3

2. Depth notch gauge including V & U notch, angle & radius. 3. Self centering tong. 4. V - notch milling cutter. 5. U - notch milling cutter

Maximum Capacity 300 J/168 J

Minimum Scale Graduation 2J

Overall Size (Approx.) 1.65 m (H)

1.1 m x 0.45 mx

Net Weight (Approx.) 375 Kg.

62. Iron jack plane 9” Iron jack plane 9” for lab purpose

63. Jigs & Fixture. Jigs & Fixture. For lab purpose

64. Kaplan turbine test rig Kaplan Turbine Test Rig (1 KW capacity 5HP supply pump)

Test rig consists of a Kaplan turbine designed for laboratory experimental

purposes and to conduct test in metric units. The specifications of the turbine

are as follows:

Normal Speed - 2200 RPM.

Capacity - 1.0 KW

a) The unit should consists of a cast iron casing, a rotor assembly of

shaft, an axial flow gunmetal runner and a brake drum on a suitable sturdy

base. The runner with vanes of aerofoil section. Fixed guide vanes should be

provided in the turbine to regulate the flow into the runner. A conical draught

tube is connected to the turbine outlet by a bend. For observing the flow at the

runner exit a transparent window made of thick Perspex tube to be provided in

between the turbine casing and the draft bend. A rope brake arrangement with

a set of dead weights and spring balance must provided for loading the turbine.

Pressure gauge and vacuum gauge to be fixed at the inlet and outlet to measure

the net supply head to the turbine.

b) Water to the turbine is provided by a centrifugal pump set of 5HP

capacity. The pump to operate on 440Volts, 3 Phase, 50 Hz line.

c) Other standard accessories include a DOL starter, switch, flow control valve,

suitable piping.

d) Flow measuring unit consists of a venturimeter with pressure taps connected

to two pressure gauges mounted on a panel board.

e) The complete test rig must be mounted on a storage tank of suitable capacity.

The tank to be provided with FRP lining for total rust protection

65. Laddles 5 kg capacity (Manually operated)

66. Laddles 10 kg capacity (Manually operated)

67.

Lathe M/c with motor

complete set 4’6” and

other accessories.

LATHE MACHINE (2 HP):

Length: 4’ - 6”, Height of Centre: 212 mm, Width of Bed : 280mm, Max Swing

Over Bed : 410mm, Max. Swing Over Slide : 240mm, Spindle Bore : 52mm,

Spindle Nose : 6 TPI, Spindle Speed 6 (RPM) : 40 to 550, Cross Slide Travel :

240mm, Lead Screw TPI : 4 TPI, Tail Stock Sleeve : MT-4, Power Required : 2

H.P.

68. lgnition system of

Automobile

lgnition system of Automobile of petrol & diesel type

69.

Losses in Pipe Fittings,

Sudden Enlargement

& Contraction System

Components:

Centrifugal Pump: ½ HP. Tullu/ Reputed Make

Constant Head Tank Sump Tank- 50 Liters Measuring Tank-0 Ltrs.

Pressure taping- piezo meter Set of Pipes (i) G.I. Pipes-1/2 (ii) G.I. Pipe- 1” Set of

Fittings: Elbow, Long bends, Short bends, Sudden enlargement and Sudden

contraction. Set of Valves, Ball valve, Gate valve, Needle valve manometer panel

consisting of transparent tubes mounted on a graduated screen of height 200

mm aprox. Pipe and fittings made of PVC/Corrosion resistance plastic Digital

stop whatch

Stand, Operation & maintenance manual will be provided.

70. Magnetic Particle

Testing M/C

1) Input Supply: AC 220V, 50 Hz, Single Phase Supply

2) Load Current: 2.5 Amp

3) Pull Force: 24 Kg in HWDC and 7 Kg in AC

4) Electronics: Solid state circuitry housed in the moulded casting

5) Features: AC current with variable magnetization level

: HWDC current with variable magnetization levels

: Mag Button Press to ON and Release to OFF

6) Duty Cycle: TWO minutes ON; TWO minutes OFF

7) Pole adjustment: 0 to 300 mm

8) Weight: 4 Kg max

Standard Accessories --

Test bar, Magnetic field indicator, Spray Bulb, Magnetic powder (Dry), Carrying

case

71. Main line boring

machine

Main line boring machine

72. Marking gauge. Marking gauge.for lab purpose

73. Mechanical Measuring Tool kit contains measuring instruments like micrometer, vernier calliper, gear

tool kit. tooth vernier, gauge etc.

74.

Meta centric Height

Apparatus

Technical Details: Pontoon: size 300X300mm (Approx) with a Horizontal Guide

Bar for adding weight and Removable Strips. Graduated Arc with pointer with

moveable hanger and set of weights. Water Tank: Size 600X450X400mm

(Approx) Front window of Tank: Made of Glass/Perspex. A set of weights is

supplied with the apparatus. Tanks will be made of stainless steel pendulum

sand graduated are for accurate measurement of Tilt angle.

75. Meter Saw blade dia

254 mm power 2000

watt.

Dia. 254 mm, power 2000 watt.

76.

Milling standard

specification.

UNIVERSAL MILLING MACHINE (Both Horizontal & Vertical):

Surface of Table mm: 1050 x 250, Dist. Between T-Slot: 62mm, Longitudinal

Travel of Table: 600mm, Cross Travel of Table: 230mm, Vertical Adjustment of

Table: 450mm Dist. Between Centre line of Spindle to Lower Surface of Over

Arm: 115mm Taper in Spindle: ISO 40, Dia. Of Milling Arbor: 25.4 mm, Range of

Spindle Speed: 9 (40 to 960), No. of Feeds: 3 Feeds, Motor 1440 RPM: 2 HP

77. Model of Francis

Turbine. model for lab demonstration purpose

78. Model of Kaplan

Turbine model for lab demonstration purpose

79. Mortise gauge. Mortise gauge. For lab purpose

80. Moulding boxes 14”X14”X3”.

81.

Multi cylinder four

stroke diesel engine

test rig.

Four Cylinder Four Stroke Water Cooled Diesel Engine Test Rig.


start, diesel engine. Type of Loading: Hydraulic Brake Dynamometer / Eddy

Current Dynamometer Fuel measuring system: Fuel measuring system consists


measuring system: Air tank fitted with orifice and water manometer.

Measurement of Heat carried away by cooling water:- Meter and temperature

sensor.

Temperature Measurement :- Digital Temperature Indicator with multi-channel

switch Temperature sensors : RTD PT-100 type

Electric Supply: Single Phase 220 V, 5 Amps Continuous water supply: 10 LPM

approx. Fuel: 20 liters (Diesel) Tachometer: For RPM measurement. Battery: 12

Volt 88 Amp.

82. Notches (V and

rectangular)

plates -2 nos ( rectangular, ,V-notch) notches ;- hook gauge is made of Nickel

plated brass scale with vernier scale arrangement and gear operated. Pump-

Kirlosker made (1/2 -1 HP) mono block self priming pump. Valves are made

of gun metal for flow control , ball valve for tank drain. All tanks are made

of stainless steel. of 2-3 mm thick plate; Sump tank size 2000X500X300mm ;

Collecting tank size 500X500X500mm ; Notch tank size 200X200X 1500mm

with special arrangement for flow

83. NOZZLE METER WITH NOZZLE METER WITH PUMP

PUMP

84. Oil fired furnace Oil fired furnace

85. Oil stone 6”x2”x1” Oil stone 6”x2”x1” for lab purpose

86. Old diesel Geep Good

working condition

Suitable for lab demonstration

87. Old Maruti 800 Good

working condition

Suitable for lab demonstration

88. Oxygen cylinder

regulator

Oxygen cylinder regulator

89.

Parallel flow/counter

flow heat exchanger.

1 System : Water to Water 2 Length of Heat Exchanger : 1.6 m(approx.) 3 Outer Tube : Material Stainless steel, ID 27.5mm, OD 33.8 mm (approx). 3 Inner Tube : OD 12.7mm (approx) 4 Water Flow Measurement : Measuring cylinder & Stop Watch with Rotameters (2Nos.) one each for cold & hot fluid 5 Hot Water Tank : Made of Stainless steel Insulated with ceramic fiber wool. 6 Hot Water Circulation : Magnetic Pump made of Polypropylene to circulate Hot Water. Maximum working temperature is 85°C. 7 Heaters : Nichrome wire heater (2 Nos.) 8 Temperature Sensors : RTD PT-100 type 6 Nos. 9 Control panel : Digital Temperature Controller: 0-199.9°C (For Hot Water Tank), Digital Temperature Indicator: 0-199.9°C,with multi-channel switch, On/Off switch, Mains Indicator etc A good quality painted rigid MS Structure should be provided to support all the parts.

90. Parallelogram of force

apparatus.

A wooden board of 50x60 cm. with wall brackets, two frictionless clamp pulleys

and three set of slotted weights of iron nickelled each set containing four weight

and one hanger of 50gms.

91. PC Based 2 stroke 1

cylinder diesel engine

test rig.

PC Based 2 stroke 1 cylinder diesel engine test rig.

92.

PC Based 4 stroke 4

cylinder diesel engine

test rig.


start, diesel engine. Type of Loading: Hydraulic Brake Dynamometer / Eddy

Current Dynamometer Fuel measuring system : Fuel measuring system consists


measuring system : Air tank fitted with orifice and water manometer.

Measurement of Heat carried away by cooling water:- Meter and temperature

sensor.

Temperature Measurement :- Digital Temperature Indicator with multi-channel

switch Temperature sensors : RTD PT-100 type

Electric Supply: Single Phase 220 V, 5 Amps Continuous water supply: 10 LPM

approx. Fuel : 20 ltrs (Diesel) Tachometer : For RPM measurement. Battery: 12

Volt 88 Amp.

The arrangement should be inter phased with PC.

93. Pelton wheel turbine

model

Pelton wheel turbine model

94. Pelton Wheel Turbine

Test Rig.

System Components: Pelton turbine unit. Dynamometer, Pressure

Gauge Flow meter-venturimeter, Manometer, AC Motor- Valves, Pipes, Electric

cables, Sump tank, Centrifugal pump to power the turbine Set of weights. Digital

Tachometer. Operational Manual and Maintenance Manual will be provided.

95. Permeabiliy Meter It is used to determine porosity in Raw sand, Green sand .

With Air Tank, Water Tank, Manometer Unit, Permeability Chart,2 Orifices

and Syphon Unit.

96. PETROL ENGINE 5 HP CAP; OST RPM, 3600 SINGLE CYLINDER

97. PLANER MACHINE:

Length of Bed: 2895 mm, Length of Table: 2060mm, Stroke of Table: 2060mm

Width of Table: 790mm, Planning Width: 1245mm, Height under Cross Rail:

1095mm, HP Required: 3

98. Pneumatic Trainer Kit. Pneumatic Trainer Kit.

99. Porker Drum turning

machine

Porker Drum turning machine for car

100.

Power Hack Saw M/C

with blade adjusting

arrangement.

POWER SAW:

semi hydraulic Mechanical

Cutting Round: 165 - 150

Capacity Square: 150 - 125

No. of Stroke Per min: 65 - 80

Blade Size (mm): 350 - 350

Approx Weight Kg: 300 - 150

Motor (1440 RPM): 1 HP - 1 HP

101.

Power Hacksaw

cutting machine.

Power hacksaw machine with assoserries Hydraulic control hacksaw machine

; with all standard accessories :like Mechanical coolant Pump, Motar pulley,

Starter plate, length guage, Flexible coolant pipe Other extra asscessories like

v-belts,Hyraulic oil , bar stand , Mortor, Starter, electrical Wiring, Three Speed

gear Box

102. Power Press Power Press

103. Power Saw 14” Power Saw 14”

104. Power Saw 14” Blade Power Saw 14” Blade

105. Press shearing

machine. Press shearing machine.

106. Rapid Sand washer

Electrically operated

Rapid Sand washer Electrically operated

107. Reciprocating pump model for lab demonstration

108. RECTANGULAR

NOTCH WITH 200

LITRE WATER TANK

RECTANGULAR NOTCH WITH 200 LITRE WATER TANK

109. Refrigeration & Air

Conditioning Model

with all accessories.

Refrigeration & Air Conditioning Model with all accessories.

110.

Refrigeration cycle

test rig.

Refrigeration Test Rig.

Technical Details :-

Compressor : Hermitically sealed compressor.

: Capacity 1/3 Ton, Kirloskar Make.

Agitator : Compatible capacity.

Condenser : Air cooled compatible to 1/3 Ton compressor

Condenser cooling fan : Compatible capacity with permanent lubricated motor.

Made of Stainless Steel, Insulated with ceramic wool / P.U.F. Rotameter : Make

Eureka Range 6 to 60 LPH.

Expansion Device:- Capillary Tube, Compatible capacity.

Pressure Gauge:- 2 Nos. Safety Control :- Overload and over current protectors

for compressor and Time delay circuit. Temperature Sensor:- RTD Pt-100 type.

Control Panel comprises of :-

Digital Voltmeter:- 0-300 V Digital Ammeter :- 0-5 Amp.

Temperature Measurement:- Digital Temperature indicator with Multi-channel

switch. All other accessories like Hand shut off valves, filter drier and

Thermostat will be provided. All the accessories will be mounted on a rigid base

frame made of M.S. and it will be powder coated.

111. Ripsaw engine brand

(fitted in wooden)

Ripsaw engine brand (fitted in wooden)

112. Rockwell Hardness

Testing M/c Rockwell Hardness Testing M/c

113. Rockwell Hardness

Testing M/C.

Load (kgf) -- 60,100,150 Initial load (kgf) - 10 Max.test height (mm) - 225 Depth of throat(mm) – 130 Max depth of elevating screw below base (mm) - 260

Size of base (mm) - 165 x 425

Machine height (Approx)mm – 650

Nett Weight(Approx.) kg - 65

STANDARD ACCESSORIES Testing table 50 mm ø – 1 pc Testing table 40 mm ø with 'V' groove for round jobs-6 to 45 mm dis 1pc Diamond Indentor 120° - 1 pc

Steel Ball Indentor 1/16" – 1 pc Test Block Rockwell 'C' – 1 pc Test Block Rockwell 'B' –1 pc Alien Spanners -- 2 pc Clamping device – 1 pc Dash - Pot oil – 1 bottle Rubber bellow for elevating screw protection – 1pc Instruction Manual - 2 books

114. Sand Mixer

Electrically operated

Sand Mixer Electrically operated

115. Sand rammer for

preparing the A.F.S.

test

Specimen 2” diameter X 2” height

116. Screw Jack Small size, experimental model, an aluminium turned pulley of about 10cm dia. Is fitted on a screw jack fitted on a 12cm dia. Metallic circular base with an adjustable pulley and a linear verticle scale. Overall height of model is about 15cm

117. Searl’s apparatus. Made of brass, nickel plated with complete set (a) working length 50m with two scales and suitable weights (b) working length 100m with three scales & suitable weights. Simply supported beam of 1m long with two hangers for weights 1-6kg

118. Set of Sieves for

different sieve.

Set of Sieves for different sieve.

119.

Shaper m/c with all

accessories.

SHAPER MACHINE:

Machine Size: 24”, Maximum Stroke: 26”, Length of Ram: 50”, Max. Dist. Of

Table to Ram: 19”, Min. Dist. of Table to Ram: 2”, Max. Vertical travel to tool

slide: 7”, Length And width of table top.: 25” x 15”, Length and width of table

slide: 37.1/2” x 12”, Length of cross slide: 37.1/2”, Width of Ram: 12.1/2”, No. of

Speeds: 4, HP Required (1440): 2

120. SHAPER MACHINE

22” STROKE.

Shaping machine with assoserries Heavy duty shaper with a max stroke of 750 mm; Length of ram approx 1450 mm; Ma and min distance from table to ram-475 X90 Working table of 750 X 375mm min.Angular movement of table on either side is 30 0.; Base 1800 X 625 mm; 4 speds -all geared min 5 - 6 HP capacity; Max swivel of tool head on either side is 60 0 ; With all necessary standard accosiries

121. Shearing m/c

professional portable

2.8 mm

Shearing m/c professional portable 2.8 mm for lab purpose

122. Sheet Bending M/c

blade 8’ Sheet Bending M/c blade 8’ for lab purpose

123. Shock absorber Suitable for lab demonstration for standard 1000 cc car

124. Sieve shaker Machine

Electrically Operated

Sieve shaker Machine Electrically Operated

125. Simple Lath m/c

medium duty with

motor complete set

4’6” Automatic heavy

duty.

LATHE MACHINE (2 HP):

Length: 4’ - 6”, Height of Centre : 212 mm, Width of Bed : 280mm, Max Swing

Over Bed : 410mm, Max. Swing Over Slide : 240mm, Spindle Bore : 52mm,

Spindle Nose : 6 TPI, Spindle Speed 6 (RPM) : 40 to 550, Cross Slide Travel :

240mm, Lead Screw TPI : 4 TPI, Tail Stock Sleeve : MT-4, Power Required : 2

H.P.

126. Simply supported

beam.

Simply supported beam.

127. Single cylinder 2

stroke diesel engine

test rig.

Single cylinder 2 stroke diesel engine test rig.

128.

Single Cylinder air

cooled four stroke

petrol engine test rig

(3 HP@3600 RPM)

The following experiments can be carried out. 01.Bhp Measurement 02. Brake Thermal Efficiency 03. Fuel Consumption Measuement 04. Air Intake Measurement The Engine Test Rig Should Facilitate To Evaluate TheFollowing - Performance at various throttle position - BHP measurement from no load to full load Description capacity to load the engine upto 3HP at 3600 RPM along with Resistance loading arrangement provided with selector switches.

129.

Single Cylinder two

stroke petrol engine

test rig.

System Components :-

I.C. Engine : Single Cylinder Two stroke Petrol engine 5.0 HP Dynamometer suitable for above mentioned engine.

(A) Rope Brake Dynamometer

Calorimeter – Shell & Tube type heat exchanger will be used. Water – cooled

Air Box- MS powder coated / PVC air box with orifice meter will be used. Manometer: U tube water manometer will be used. Fuel Tank, Capacity 5 Litres Burette: 0-100ml calibrations, with three way selection cock & stopwatch. RPM Indicator : 0-9999 RPM Base frame- made up of ms C channel duly powder coated. Control Panel – for mounting of all indicators Electrical switches & wiring Measuring Jar Piping & Wiring

130.

Single stage air

compressor test rig.

Compressor: Single Stage, Capacity 4 CFM (Max.), Working Pressure 5 kg/cm2

max. Drive: 1HP Crompton/ GE/Equivalent Motor, Manifold Tank: Suitable

capacity. Flow Measurement: Orificemeter with Manometer. Temp.

Measurement: Thermometer 2 Nos. Air Tank: Capacity 100 Ltrs. With safety

valve, shut off valve. Pressure gauge; Bourdon type. Control Panel comprises of:

Energy measurement: Electronic Energy meter, L&T/ Equiv.

131. Single Stage

Reciprocating Air

Compressor Test Rig.

Technical Details: Compressor: Single Stage. Capacity 4 CPM (Max.), Working

Pressure 5 kg./cm2 max. Drive: 1 HP (Crompton/GE/Equivalent Motor.

Manifold Tank: Suitable capacity, Flow Measurement: Orificemeter with

Manometer. Temp. Measurement : Thermometer 2 Nos. Air Tank: Capacity 100

Ltrs. With safety valve, shut off valve. Pressure gauge: Bourdon type Control

Panel Comprises of: Energy measurement: Electronic Energy meter. L&T /

Equiv.

132. SLOTTING MACHINE:

10 TO 250MM, Longitudinal Move: 230mm, Cross Movement: 230mm, Speed

Adjustment: 3 Speed, Ram Adjustment: 250mm, HP: 1.5H.P., A: 330mm, B:

410mm, Extra Accessories: Rotary Table with 36:1 Ration (250mm), Electric

Motor True Chuck Switch V-beit.

133. Spot welding machine.

Particular

6KVA 8KVA 10KVA 15KVA 20KVA

Max. Weld Ability

M. S. x 2 1.6 mm 1.8 mm 2 mm 3 mm 3 mm

S. S. x 2 1.4 mm 1.6 mm 1.8 mm 2.8 mm 2.8 mm

Br. x 2 0.6 mm 0.7 mm 0.8 mm 1 mm 1 mm

134. Spray Gun High volume ,low pressure ,size 1/4 inch

135.

Surface grinding

machine.

Precession Surface Grinding Machine with assoserries of Standrard makewith the following specifications;- max grinding length;-520mm; max grinding witdh-200mm; max distance bet table surface to spindle centre-490mm ;Table size 450 X210 mmlongitudinal table travel480-520mm : cross taravel-190 to 230mm. Longitundinal hand feed 100mm; Cross movement hand feed graduations 0.2mm; Vertical movement hand feed-.005mm; with hyraulic pump motar of 1 HP; Spindle motar 1.5 to HP;Grindi wheel speed 50HZ to 60HZ ( 3000 to 3600rpm)

136. Thermal conductivity

apparatus (thin, thick

& composite wall)

Thermal conductivity apparatus (thin, thick & composite wall)

137. Tig welding machine.

Welding machine ( TIG arc ) withal necessary attachments needed for

performing welding in lab.

138. Tool kit almirah

godrej almirah 6’x’4’ Tool kit almirah godrej almirah 6’x’4’

139. Torsion Testing

Machine Suitable for Torsion and Twist test on various metal rods and flats.Torque Measurement by pendulum dynamometer system.Auto torque selector to adjust torque ranges.Geared motor to apply torque to specimen through gearbox.Autographic recorder for relation between torque and angle of twist.

Accuracy + 1 % of the true torque

Max. Torque Capacity (Nm) 100

Torque Range (Nm) 20,50, 100

Nos. of Division on dial 500

Test speed and direction 1.5 RPM Reverse

Clearance between grips (mm) 0-400

Grips for square bar (mm) 3-6 6-9 9- 12

140. Triangular file 4” Triangular file 4”

141. Two stage

Reciprocating air

Compressor with all

5 Horse Power, 230V 2-stage air compressor - no starter required

accessories. 175 psig maximum operating pressure and 80 gal. ASME tank

15.8 CFM @ 90 PSI,

Accessories & manual to be provided

142.

Two Stage twin

cylinder air

compressor test rig.

Compressor Two Stage, Twin Cylinder air compressor-3 HP with a displacement capacity of about 300 LPM and to work against maximum pressure 12Kg/Cm2 The Unit is mounted on a storage tank. Controls The Unit is supplied with pressure switch, suction filter safety valve, pressure gauge, water drain valve air delivery valve etc. Air Intake Measurement An orifice tank with orifice plate, manometer with pressure tapings are provided to measure the volume of air sucked by the compressor. Electric motor 3 HP/3 Phase electric motor Instrumentaion Digital temperature indicator to measure suction and delivery side temperature of the compressor. Pressure gauges to measure stage pressure

143. Ultrasonic Testing

M/C

Test Range- 10 mm to 5 meter (in steel) adjustable in 1mm or 10mm step.

Velocity - 1000 m/s to 9999 m/s adjustable in 1 m/s or 10 m/s step

Delay- Up to 3 meter adjustable in 0.5mm or 5mm step

Display- High brightness colour TFT LCD display. Display area 122x92 mm

(320x240 pixel). Eleven different colour scheme options.

144. Universal Testing

Machine 20 Metric ton

1. No. of Column - 02 2. Load (kN) - 20 3. Max Test Speed(mm/min) - 500 4. Min. Test Speed(mm/min.) - 0.01 5. Max. Force at fullspeed (kN) - 20 6. Max. Return Speed(mm/min.) - 1000 7. Position Control (mm) - 0.5 8. Total CrossheadTravel (mm) - 1130 Results Parameters: Ultimate Load, Ultimate Strength,

Displacement at Ultimate Load, Maximum Displacement, %Elongation, %

Reduction in area, Breaking Load, Breaking Stress, Yield Load, Yield Strength,

0.02% Proof Strength, 0.1% Proof Strength, 0.2% Proof Strength, 0.5% Proof

Strength, , 1% Proof Strength, all Proof loads, Young’s Modulus; Results: Fully

customized result window,

Fully Customized Test Report.

145 Universal Testing

Machine 40 Metric ton

1. No. of Column - 02

2. Load (kN) - 40

3. Max Test Speed(mm/min) - 500

4. Min. Test Speed(mm/min.) - 0.01

5. Max. Force at fullspeed (kN) - 40

6. Max. Return Speed(mm/min.) - 1000

7. Position Control (mm) - 0.5

8. Total CrossheadTravel (mm) - 1130

Results Parameters: Ultimate Load, Ultimate Strength,

Displacement at Ultimate Load, Maximum Displacement, %

Elongation, % Reduction in area, Breaking Load, Breaking Stress, Yield

Load, Yield Strength, 0.02% Proof Strength, 0.1% Proof Strength, 0.2%

Proof Strength, 0.5% Proof Strength, , 1% Proof Strength, all Proof

loads, Young’s Modulus; Results: Fully customized result window,

Fully Customized Test Report.

146 Valve Refacer Valve Refacer

147 Vapor Compression

Refrigeration System

Test Rig.

Technical Details : Compressor : Hermitically Sealed compressor

Capacity : 1/3 Ton, Kirloskar Make.

Agitator : Compatible capacity.

Condenser : Air cooled compatible to 1/3 Ton compressor

Condenser cooling fan : Compatible capacity with permanent.

Lubricated motor. Made of Stainless Steel, Insulated with ceramic wool / P.U.F.

Rotameter : Make Eureka Range 6 to 60 LPH.

Expansion Device : Capillary Tube, Compatible capacity.

Pressure Gauge : 2 Nos. Safety Control: Overload and over current

Protectors for compressor and Time delay circuit, Temperature

Sensor: RTD Pt-100 type. Control Panel comprises of:

Digital Voltmeter:0-300 V Digital Ammeter: 0-5 Amp.

Temperature Measurement: Digital Temperature indicator with

Multi-channel switch. All other accessories like Hand shut off

Valves, fitter drier and Thermostat will be provided. All the accessories will be

mounted on an rigid base frame made of M.S. and it will be powder coated.

148

Variable speed air

blower test rig.

1) 3 hp variable speed motor tocrive the impeller

2) Impellers : a – Forward vanes

b – Radial vanes

c – Backward vanes

3) Orifice and manometer to measure air flow

4) Flow control valve on discharge side

5) Energymeter to measure input

Three different type of impellers can be fitted over the shaft . Air

discharge to measure by venturimeter. The impeller can be rotated at different

speed and performance of blower can be estimated at different speed and

dischsrge heads.

149

Venturimeter, Orifice

meter & Rota Meter

Test Rig.

System components:

Centrifugal pump: ½ HP Tully/reputed make

Constant Head Tank, Sump Tank (50 Ltrs)

Measuring Tank, Orifice Meter

Venture Tube: Inlet and outlet diameter 25 mm, Rotameter

U tube Manometer consisting of transparent U tube mounted on a

Graduated screen of height 400mm approx.

Pipe and fittings made of PVC/Corrosion resistant plastic

Piezo Meter, Digital Stop Watch, Stand.

Operation and Maintenance manual to be provided.

150 Vicker’sl Hardness

Testing M/C.

Vicker’sl Hardness Testing M/C.

151 V-NOTCH WITH 200

LITRE WATER TANK. V-NOTCH WITH 200 LITRE WATER TANK.

152 Welding generator. Welding generator.

153 Welding Machine. Welding Machine.

154 Winch crab

single/Double

Purchase

Fitted with heavy cast iron wall brackets. The grooved wheel is of 25 cm

diameter and gears are machine cut.

Winch Crab Single Purchase: This apparatus is used for experiments in

efficiency of mechanical advantage..

Winch Crab Double Purchase: This apparatus is used for experiments in

efficiency of mechanical advantage. With double set of gearing arrangement.

155

Wood lathe machine.

Height of Centre : 200mm Distance between Centres : 1200mm Spindle Bore : 20mm with MK3 Internal Taper Range of Speeds : 425 to 2800 rpm Motor Drive : 2 H.P. ACCESSORIES: STANDARD Appropriate Spanners : 1 Set Appropriate sizes Allen Keys : 1 Set Instruction & Operating manual must be provided.

156 Wooden planer m/c

4’x’6’ Wooden planer m/c 4’x’6’

157 Working table

(Salwood) 7’x4’ x 2 ½ ‘ Working table (Salwood) 7’x4’ x 2 ½ ‘

158 Worm and worm

wheel

An all metallic self contained apparatus useful for demonstrating the

efficiency of worm and wheel and also the principal of work. Consisting of

a machine cut worm gear of 25 cm diameter, carrying a metal drum of 12 cm

diameter, and machine cut worm on steel spindle carrying a 12 cm diameter

pulley. The whole arrangement is fixed on heavy cast iron bracket capable to be

fixed to a wall. Complete with effort pulley, string and hooks with weights. A)

Single Purchaseb) Double Purchase

159 X-ray Radiography

Testing M/C

X-ray Radiography Testing M/C to demonstrate non- destructive test in lab

DST-04- List of Civil Engg. Equipments

SN EQUIPMENT NAME SPECIFICATION 1.

Aggregate Crushing Value

Apparatus

Conform to IS 9376-1979 HA 50.85 with steel cylinder75mmdia,150mm dia and Plunger The equipment consist of the following replaceable parts: Cylindrical Cell Plunger Base Plate Tamping Rod 10mm dia.x230mm long. Metal measure

2. Aggregate Impact Value

Apparatus

Conform to IS 9377-1979 A heavy circular base with two vertical guides fitted with a cross bar at the top. A hammer of 13.75 kg, mass which can be raised and allowed to fall freely through 380 1 5 mm with locking arrangement. Cylindrical Cup Metal Measure Tamping Rod 10mm dia.x23Omm long. Automatic Blow Counter

3. Apparatus for determination of metacentric height

(i)Reservoir Tank size: 500X500X200mm (ii)Ship model size: 230X350 mm (iii)circular Weights: 4 Nos (iv)Graduated Arc for measuring tilt angle. (v)Detailed Technical Manual and On-site deomo

4. California Bearing Ratio Test Apparatus

(i)Motorised Load Frame having single rate of strain of 1.25 mm/m, Capacity 5000kg (50KN) (ii)CBR mould 150 mm base plate and collar inner dia X 175 mm high. (iii) Cutting Collar. (iv) Perforated swell plate (v) Spacer disc. (vi) Metallic ring made of mild steel. (vii) Metal tripod aluminium (viii) Penetration Piston Assembly. (ix) Proving ring 10KN capacity (x) Surcharge weight, 2.5 Kg and 5 kg, 147 mm dia with 53 mm dia central hole. (xi) Surcharge weight, 2.5 and 5 kg. 147 mm dia with 53 mm dia slot. (xii) Dial gauges- 2 Nos 0.01 mm X 25mm (xiii) High sensitivity Proving Ring 3000kg capacity with calibration chart and carrying case. (xiv) compaction Rammer 2.6kg X 310 mm fall. (xv) Compaction Remmer 4.89 kg X450 mm fall.

5. Casagrande Apparatus for

Liquid Limit & Plastic

Limit Test

Liquid Limit Device, Motorised, Grooving tool Suitable for operation on 50Hz., Single Phase AC supply Plastic limit set comprising of glass plate, Brass Rod, Spatula, Moisture Tin and Porcelain Dish

6. Closed circuit bernoullis theorem apparatus

(i)converging Diverging Perspex test section:200 mm (ii) No of pressure Tapping : 8Nos (iii) sump tank capacity:100 litres MoC : 18X18X24 electro Plating tank (PVC) (iv) Volumetric tank capacity : 40 liters. MOC: SS- 304 with malt Buffing. (v) Pump: Monoblock type 0.5 HP (vi) Piping with necessary valves and fittings. (vii) Digital stop watch with 1/10 second Accuracy. (viii) detailed Technical Manual and on-site demo. (ix) Control Panel On /off switch, Mains indicator, etc.

7. Closed circuit calibration test rig for measuring discharge water through Rota Meter

(i)Scales- 10-100% of flow, 250 mm length (ii)Mounting Type- Panel (iii)End fittings- Brass std; 316 SS Optional (iv)Process Media Type (v)Suspended Solids/ Slurries

(vi)Media Tempeature- 2000 𝐹 for liquid 2500 𝐹 for gas (vii) Piping Class- A1, B1, D1, E1, F1, SF1, PA1, PB1, PD1, PE1, PXF1, A2, B2, D2, E2 (viii) transmitter – 2- wire magnetic type, 24 volt DC, 4-20 mA. (ix) accuracy ±2% full scale or better (x)Repeatability ± 0.5%full scale (xi) Glass Tube – Borosilicate glass (xii) float Stops- 316 stainless steel spring wire (xiii) O-Rings- viton std; Buna N optional (xiv) Housing – Die cast aluminum alloy 380, not wetted (xv) Tube Retainer- ABS, not wetted (xvi) Threaded Fasteners- 18-8 stainless steel, not wetted (xvii) Shield- Polycarbonate, not wetted

(xviii) Connection- 3 4 Inch FNPT Horizontal

(xix) Dimensions - 4.25 Inch W, 3.5 Inch D, 19 Inch H, 17.5 Inch centerline port- to port (xx) Range- Normal flow rate between 50 % and 100% of the instrument range. (xxi) Control Panel On /off switch, Mains indicator, etc.

8. Closed circuit francis turbine test rig.

Design speed – 1500 r.p.m., Output Power -3.7kW(5.0HP), design Head and discharge 15-20 m and 1800-2000lpm., cast iron spiral casing, a rotor assembly of shaft, gunmetal runner and brake drum all mounted on a sturdy base, Aerofoil shaped gunmetal guide vanes, Conical draught tube . stainless steel for corrosion resistance., centrifugal monoblock pump set of 15HP capacity of size.flow measuring unit – venturimeter of size 100mm, Operatable on 440 Volts, 3phase, 50Hz line. complete test rig is mounted on a storage tank of suitable capacity.

9. Closed circuit Kaplan turbine test rig

Design speed – 2200 r.p.m., Output Power -1kW, cast iron spiral casing, axial flow gunmetal runner and brake drum all mounted on a sturdy base, Aerofoil shaped gunmetal fixed guide vanes, centrifugal pump set of 5HP capacity of size.flow measuring unit – venturimeter of size 100mm, Operatable on 440 Volts, 3phase, 50Hz line. complete test rig is mounted on a storage tank of suitable capacity.

10. Closed circuit multispeed single stage centrifugal pump test rig

A close circuit through which water circulated continuously by means of a centrifugal pump of 25mm X 25 mm couple to make the supply from sump tank. (i)Sump Tank MOC : SS-304, Capacity :1200 mmX500mmX 1500mm. with 1”drain valve of 15mm size .in the bottom of tank (ii)collecting Tank: MOC : SS-304, Capacity :400mmX400mmX400mm. with drain valve of 25mm size. (iii) Pump- Type : D.C motor of 1HP (iv)Motor drive- AC to DC convertor

11. Closed circuit pelton wheel turbine test rig 5HP

Design speed – 750-900 r.p.m., Output Power -3.7kW(5.0HP), design Head and discharge 46-50 m and 700-900lpm., cast iron body with a large transparent acrylic window a nozzle and spear arrangement, a bearing pedestal, a rotor assembly of shaft, runner and brake drum all mounted on a sturdy base. Buckets – Gunmetal , spear made of stainless steel for corrosion resistance., centrifugal monoblock pump set of 15HP capacity of size., Opera table on 440 Volts, 3phase, 50Hz line. complete test rig is mounted on a storage tank of suitable capacity.

12. Closed circuit pipe friction apparatus

(i) Box Dimension : 2000X 500X 1400mm (ii) U- tube manometer: 300-0-300 (Mercury filled) (iii) Number of Pipe : 3 Nos. (iv) Test Length :1 meters.

(v) sump tank capacity:100 litres MoC : 18X18X24 electro Plating tank (PVC) (vi) Volumetric tank capacity : 40 liters. MOC: SS- 304 with malt Buffing. (vii) Pump: Monoblock type, 0-60 litre/min., Motor 0.5 HP (viii) Piping with necessary valves and fittings. (ix) Digital stop watch with 1/10 second Accuracy. (x) detailed Technical Manual and on-site demo. (xi) Control Panel On /off switch, Mains indicator, etc.

13. Closed circuit reciprocating pump test rig

(i)Sump Tank MOC : SS-304, Capacity :120 liters with 1”drain valve of ball type. (ii)Measuring Tank: MOC : SS-304, Capacity :80 liters. (iii) Pump- Type : Reciprocating – Double Acting, Pump Bore: 44.5mm, Pump Stroke:35mm, suction Pipe:25mm, Delivery Pipe :19mm, Pump speed: 210r.p.m., Power: 1HP, Motor Speed: 1440 r.p.m/, V Belt Size: A48, Capacity : 1400 LPH (approx), Suction Lift: 7.5 meter, Total head:30meter, Pressure: Tested upto

6kg/𝑐𝑚2 , Max. head: 5kg/𝑐𝑚2 , Provided with air vessel. (iv)Motor drive- 1HP DC, Type:Thyristor control for variable speed, Pressure Gauges:-Type : bourdon tube type, control Panel.

14. Closed Circuit rectangular/V. notch tank apparatus

(i)Open flow channel: 250X200X 1000mm (ii)rectangular Notch:50mm wide (iii)Triangular Notch: 450 and 600 (iv) Sump Tank Capacity:100 litres MoC : 18X18X24 electro Plating tank (PVC) (iv) Volumetric tank capacity : 40 liters. MOC: SS- 304 with malt Buffing. (v) Pump: Monoblock type, 0-60 litre/min., Motor 0.5 HP (vi) Piping with necessary valves and fittings. (vii) Digital stop watch with 1/10 second Accuracy. (viii) detailed Technical Manual and on-site demo. (ix) Control Panel On /off switch, Mains indicator, etc.

15. Closed circuit Reynolds apparatus

(i)A sump tank : 550 X 430X 225. (ii) Flow pipe length :700mm (iii) Measuring Flask 1Litre (iv) Pump : Submersible type. (v) Piping with necessary valves and fittings.

(vi) Digital stop watch with 1/10 second Accuracy. (vii) detailed Technical Manual and on-site demo. (viii) Control Panel On /off switch, Mains indicator, etc.

16. Compaction Factor

Apparatus

The upper conical hopper has internal dimensions as: ,. ,Top diameter — 250mm Bottom diameter - 125mm Height — 225mm The lower conical hopper has internal dimensions as: ,. ,Top diameter — 250mm Bottom diameter - 125mm Height — 225mm The cylinder has internal dimensions as: l50mm diameter and 300mm height Tamping rod steel — 10mm diax600mm length with ISI certification mark IS 10086

17. Compression Testing

Machine

Operation - Motorised Capacity — 2000 RN Least Count l0kN Max. Clearance Between Platens— 370mm Max.Distance Between Side Plates — 340mm Platen Size - 222.0 Dia Piston Dia.-222.2mm Piston Stroke-50mm

18. Digital Balance Capacity: 3.0kg, Readability 0.2gm Capacity: 6.0kg, Readability 0.5gm Capacity: 10.0kg, Readability 1.0gm

19. Digital Electronic Balance, Cap: 10 kg, Accuracy/ Sensitivity : 1gm, Complete Set. 20. Direct shear test

apparatus [Motorised] (i)Shear box assembly,60 mm square, complete with a U-bracket, guide pins and spacing screws, made of brass. (ii)Gipper assembly consisting of two plain grid plates, two perforated grid plates, one base plate and one loading pad, all made of brass. (iii)Two prorous stones, each 6mm thick, fitting the shear box. (iv) shear box housing of brass, complete with two ball roller strips.

(v)Loding unit with normal loading of 8 kg/𝑐𝑚2 on 60mm square specimen. (vi)Specimen cutter for a specimen size of 60mm X 60 mm X 25mm.

(vii) Set of weights to give a normal stress upto 3kg/𝑐𝑚2 , 3 of 0.5 kg/𝑐𝑚2 and 1 of

1kg/𝑐𝑚2 Complete Unit Electrically Operated with a turret type gear box to give twelve different rates of strain : 1.25, 0.625, 0.25, 0.125, 0.025, 0.01, 0.005, 0.002, 0.001, 0.0004,0.0002, mm/min. and arrangements to carry out residual shear strength tests. Suitable for operation with 220 volts, 50 hz. Single – phase supply.

21. Ductility Bitumen testing machine (IS:1208)

Three mould assemblies , a base plate, a water bath of 10 litres capacity with a perforated shelf for and a thermostat controller for heater. Standard rates of travel of – 1cm/mnt. And 5cm/mnt.

22. Laboratory Electric Oven Double walled oven with the inside made of thick anodized aluminium or stainless steel. Outside mjild steel finished in white enamel. The gap between the inside and outside is 75 mm and is filled with pure glass wool. Adjustable air ventilators are provided near the top on the Sides .Fitted with Air circulating fan. Dimension (mm)

455 X 455 X 455, Shelves. Digital PiD controlled, Temperature range (500 -2500𝐶), suitable for operation on 220 V, 50 Hz, Single Phase.

23. Laser Distance meter, Range- 200 meter

Display Such Screen, accuracy ± 1mm, Dia of the laser dot in mm 6,30,60mm, Tilt

sensor measuring range3600 , Photograph file format JPG hMemory 30 displays Free App ios / android Data Interface* Bluetooth @ Smart Measurements per set of batteries up to 4000

24. Le- Chatelier Apparatus Small split cylinder of spring brass or some other suitable metal of 0.50mm thicknes, 30mm internal diameter and 30mm height. On either side of the split are attached two indicators with pointed ends.

25. Liquid Limit Device, - (As per IS 2720- Part V)

(i)Hand Operated A brass bowl(cup), a adjustable bracket. a rubber of a standard hardness by cam action. Casagrande grooving tool and one ASTM grooving tool and height gauge. (ii) Motorised Same as above but fitted with a motor geared down to give 120 r.p.m. operating on 220 volts, single phase A.C. Supply.

26. Los angles abrasion test A hollow cylinder, Closed both ends, having inside diameter of 700 mm and inside

machine (As per IS: 2386-IV)

length of 500 mm. mounted on sturdy frame on ball bearings. The drum rotated by an electric motor through a heavy reduction gear at a speed of 30-33r.p.m. suitable for operation 440 volts, 3 phase 50 cycles A.C. Supply. Abrasive charge-set of 12Nos,with spares. Cast iron spheres or steel spheres (Hardened steel balls) approximately 48 mm diameter and each weight between 390-445 gram.

27. Motorised Sieve Shaker The sieve can carry up to 8 sieves of 200mm dia.. lt is driven by a 1/4 HP geared mot0r.The sieve table is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction. In addition to the gyratory motion of the table, there is tapping motion as well as. Suitable for operation on 220V,50Hz, Single Phase AC supply Adapter for 300mm dia. Sieves

28. Mould

Cube Mould:

Cast Iron l50mmx150mmx150mm with ISI Certification Mark lS:10086 Brass/Cast Iron 70.5mmx70.5mmx70.5mm with ISI Certification Mark. It can be split up in parts in order to take out the cube without any damage. The base plate is non-porous and of such a size that there should be no leakage of water from the bottom Cast Iron, Split length wisel50mmx300 high with ISI Certification Mark IS:10086 Tamping Rod, Steel, l6mmx600mm length rounded at lower end carries ISI certification Marks IS: 10086. For use with Cube and Cylindrical Moulds. Beam Mould 100mmxl00mmx500mm size Beam Mould 100mmx100mmx700mm size Tamping Bar, Steel, 25mmx25mm square ramming face, 400mm long, 2kg in weight, carries ISI certification Marks IS: 10086. For use with Beam Moulds.

29. Orifice Meter Apparatus (i) Box Dimension : 1000X 500X 1670mm (ii) U- tube manometer: 300-0-300 (Mercury filled) (iii) Orifice Diameter : 16 mm. (iv) Variable Area Meter:100-1000:PH (v) Venturimeter: Throat Diameter 16+/-1 mm.

(vi) Sump tank capacity:100 litres MoC : 18X18X24 electro Plating tank (PVC) (vii) Volumetric tank capacity : 40 liters. MOC: SS- 304 with malt Buffing. (viii) Pump: Monoblock type, 0-60 litre/min., Motor 0.5 HP (ix) Piping with necessary valves and fittings. (x) Digital stop watch with 1/10 second Accuracy. (xi) detailed Technical Manual and on-site demo.

30. Pitot tube apparatus Standard Test apparatus for laboratory 31. Proctor compaction

Apparatus (I) Standard Compaction Test – Compaction Mold – Brass

100 mm Internal dia. X 127.3 mm height X 1000 cc. Volume. Complete with collar & Base plate with rammer 2.6 kg X 310 mm controlled fall.

(II) Heavy compaction Test Compaction Mold – Brass , 150 mm Internal dia. X 127.3mm height, volume 2250 cc. Complete with collar and base plate. Rammer 4.89 Kg. X 450 mm controlled fall as for IS2720 (Part-VIII)

32. Pycnometer Pycnometer 33. Rebound Hammer

Test(SCHMlDT)

Beton -PrufhammerN/NR.Sclerometre a betonN/NR. Concrete Hammer N/NR

34. Seimen’s Rain gauge Daily and cumulative Measuring Range: 0 to 9999 mm (0 to 393.7 in), rainfall rate Measuring range : 0 to 999 mm/ hr (0 to 39.37 in /jhr) Standard Dimension

35. Seive shaker, Gyratory type

Compatible with 1.25 HP Motor, 230 volts, 50 Cycle phase, A.C. Supply. DIGITAL DISPLAY MODEL with Adaptor for 20 cm. & 30 cm. diameter sieves, Time Switch 0-06 mins in 5 mins graduation.

36. Sieve Set Standard IS: Set of Sieves Ranging from 125 mm to 750 Micron 37. Sieves, GI Frames of

300cm diameter

Size: 100mm,80mm,63mm,40mm,25nnn,20mm,12.5mm,6.3mm,4.75mm, Lid and Pan GI frame 300mm base Sieves, Brass Frames of 200cm diameter Size: 4.75mm,2.36mm,1.18mm,600µm, 300 µm,150 µm,75 µm, Lid and Pan brass frame 200mm base

38. Slump Test Apparatus (IS:7320 -1974)

(i)A slump cone 100 mm dia at the top, 200 mm dia at the bottom, and 300 mm high with two cleats and lifting handles. (ii)A base plate with clamping arrangement

(iii) Tamping rod, 16 mm dia. X 600 mm long and graduated from 0 to 15 cm in 0.5 cm spacing to measure the slump.

39. Slump Test Apparatus

with testing rod and base

plate.

lnternal Dimensions Top diameter — 100mm Bottom diameter — 200mm Height — 300mm Tamping rod steel — 10mm diax600mm length with lSl certification mark IS 10086

40. Tile Abrasion Testing

Machine

The tile sample is pressed under a specified load against a grinding path, strewen evenly with an abrasive powder revolving at the rate of 30 i 1 rpm . supplied complete with automatic pre- set revolution counter and one 7.5kg weight, but without abrasive powder and thickness measuring device. Suitable for operation on 415V, 50Hz and 3 phase AC supply Thickness Measuring Device, with Dial Gauge, having 25mm travel and 0.01mm least count. Abrasive Powder

41. Total Station Angular measurement Standard deviation per ISO17123-3, 1 σ 1) 0.5“ (0.15 mgon) Units of measurement 360° sexagesimal, 400 gon 360° decimal, 6400 mil DisplayTOUCH SCREEN 0.01 mgon; 0.1“, 0.00001°, (smallest selectable unit) 0.00001 mil Automatic reference to the horizon (2- axis liquid compensator) Working range, longitudinal/lateral 3' (0.055 gon) Setting accuracy ≤ 0.3“ (0.1 mgon) Displays LCD (liquid crystal display) 8 rows of 35 characters each 6 status fields Data storage and interfaces PCMCIA memory card RS232 programmable interface Motor and fine drives Fine drives Coarse/fine, motorised, infinite, slip coupling Motor Speed of rotation 45 °/s (50 gon/s) Positioning accuracy 0.8” (0.2 mgon)

42. Unconfined Compression Test Apparatus ( Motorised)

Proving Ring Type ( Motorised)screw operated load frame cap 5000kg. with a gear box and motor drive giving 1.25, 1.5, 2.5 mm/min rates of strain. A pair of cone seating, adaptor for proving ring and strain dial gaguge bracket. Supplied with one pair of male/ female coning tools for 38 mm, 50mm, 75mm & 100mm dia for each sample.

43. Unconfined Compression

Test Apparatus Proving

Ring Type

The equipment consists of: Load Frame, Motorised Single Speed 10kN(l000kgt) Plain Platen with Adapter and Steel Ball. High sensitivity proving ring capacity 2kN(200kgf) Dial Gauge 25mm travel,0.0lmm least count. Split Mould 38mrnx76mm long. Rubber sheath for 38mm dia specimen

44. Universal Testing

Machine

Motorised Resolution - 0.01kN Maximum Clearance for tensile test-50-800mm Maximum Clearance for Compression test-0-800mm Clearance between columns -600mm Ram stroke- 250mm Straining/piston speed at no load- 0 — 100mm For Tension Test: Clamping jaws for round specimens 10 — 25mm 25 -40mm 40 - 55mm Clamping jaws for flat specimens thickness 0 — 15mm 15 -30mm Flat specimen width 70mm For Compression Test: Pair of compression plates 222mm For Transverse Test: Table with adjustable rollers Width of rollers 160mm Diameter of rollers 50mm

Max. clearance between the supports 600mm Radius of punch tops 16mm,22mm

45. Venturimeter Material Clear acrylic compatible to 1” Dia, water circulation FHP Pump, Measuring tank capacity 40ltrs, sump tank Capacity 85 Ltrs., Stop Watch Electronic, Control Panel On /off switch, Mains indicator, etc.

46. Vicat apparatus Vicat Mould Glass Base plate Initial Setting Time Needle: 1.0mm square or l.13mm in diameter with the lower end being flat Final Setting Time Needle: 5.0mm in diameter with circular cutting edge, the end of needle projects by 0.50mm Consistency Plunger: 10mm in diameter and 50mm long with lower end flat and small projection at the upper end for insertion into movable rod. Mild Steel Base plate Vicat Mould Split Type, with Clamping Ring

47. Viscometer (Digital) IS:1206-1958

(i)Range-minimum 10cP, Maximum 500cP. (ii) accuracy – 1cP or better. (iii) Interface- with PC for data monitoring and with external thermostat for heating the sample during measurements. (iv) Coupling with RTD for direct monitoring temperature.

DST-05- List of Electronic Equipments

Sl.

No.

Name of Equipment Specification

1. MICRO-CONTROLLER BASED 25 MHz OR

MORE 2 CHANNEL 4 TRACE DIGITAL READOUT

OSCILLOSCOPE WITH BUILT IN TOUCH

COMPONENTS TESTER

MICRO-CONTROLLER BASED 25 MHz OR MORE 2 CHANNEL 4 TRACE

DIGITAL READOUT OSCILLOSCOPE WITH BUILT IN TOUCH COMPONENTS

TESTER

2. LVDT TRAINER FOR EXPERIMENTS OF – STUDY

I/O CHS, DETERMINE LINEAR RANGE,

SENSITIVITY DETERMINATION, MEASURE

PHASE DIFFERENCE BETWEEN SECENDARIES

LVDT TRAINER FOR EXPERIMENTS OF – STUDY I/O CHS, DETERMINE

LINEAR RANGE, SENSITIVITY DETERMINATION, MEASURE PHASE

DIFFERENCE BETWEEN SECENDARIES

3. STRAIN GAUGE TRAINER FOR EXPERIMENTS

OF – STUDY STRAIN MEASUREMENTS,

DITERMINE LINEAR RANGE, CALIBRATION OF

SCALES, DETERMINE SENSITIVITY ETC.

STRAIN GAUGE TRAINER FOR EXPERIMENTS OF – STUDY STRAIN

MEASUREMENTS, DITERMINE LINEAR RANGE, CALIBRATION OF SCALES,

DETERMINE SENSITIVITY ETC.

4. WORKING DEMONSTRATION MODEL FOR AC

POSITION SERVOMECHANISM.

WORKING DEMONSTRATION MODEL FOR AC POSITION

SERVOMECHANISM with minimum angular step size of 1.5 deg.

5. WORKING DEMONSRATION MODEL FOR DC

POSITION SERVOMECHANISM

WORKING DEMONSRATION MODEL FOR DC POSITION

SERVOMECHANISM with minimum angular step size of 1.5 deg

6. DIGITAL ELECTRONICS EXPERIMENTAL

BOARDS FOR EXPT. OF GATES RIPPLE,

SYNCHRONOUS COUNTERS, REGISTERS AND

A/D AND D/A CONVERTERS, ENCODERS,

DECODERS, FIBER OPTICAL DIGITAL LINKS

ETC.

DIGITAL ELECTRONICS EXPERIMENTAL BOARDS FOR EXPT. OF GATES

RIPPLE, SYNCHRONOUS COUNTERS, REGISTERS AND A/D AND D/A

CONVERTERS, ENCODERS, DECODERS, FIBER OPTICAL DIGITAL LINKS ETC.

with built-in power supply of 5 V, ammeters and voltmeters

7. CRO 4 CHANNEL storage type

CRO 4 CHANNEL storage type with storage of msec range, digital

display, component testing facilities and delay upto 100 microsec.

8. CDMA-DSSS with BIT Error Rate

Measurement

To study theory of Direct Sequence Spread Spectrum Modulation and

Demodulation (DSSS) Selection and study of various PN codes (MLS,

GOLD, BARKER) Generate signal.

To study the effect of synchronization Sequential code search in

Despreading with on board NRZ binary data bits as a data message,

Bit error rate measurement with PRBS-11

9. Basic GSM with application module Easy understanding of at commands For an experiments to : GSM

Theory & Standards Understanding of GSM technology, its network,

GSM capability & data services. Understanding RF environment &

study of GSM network by actually connecting to the GSM environment

by any service provider. Study of GSM real time working

fundamentals Appliances switching by SMS using AT commands Flow

chart provided Description /Explanation/ Visualization of the AT

commands on one screen.

10. 16 QAM Training System

VLSI Based Encoding: 4bits encoding with Symbol Mapper

Modulation: 16-QAMModulation with I & Q Channel

Constellation(Vector /XY) View User Selectable Hardware/Real-Time

Software Mode User selectable step variable clock frequency User

Selectable 8 / 16 / 32 / 64 bit Data

11 RFID Trainer

Experiment Trainer board that Contains:-

1.Modulation : ASK

2.13.56 MHz multi protocol support

a.ISO 14443A

b.ISO 14443B

c.ISO 15693

3.RS-232 Interface

4.LED Indication

5.Buzzer indication

6.Antenna

a.Type : Inductively coupled coil type

7.Operating frequency : 13.56 MHz

8.LCD Display for card identification details

9.Various test points to observe the signals

Application programme software

Learning Material CD

12 350 MHz, 2 Channel Desktop

Function/

Arbitrary Waveform Generator

4.3 inches, 16M true color TFT LCD.

350 MHz, 250 MHz or 100 MHz maximum sine

output frequency, 1 GSa/s sample rate, 14 bits

resolution. Single/dual-channel models.

The dual-channel model supports frequency and

phase coupling. The 16+2 channels digital output

module (optional) together with the analog channel

can rebuild the more mixed signals in daily practice.

13 10 MHz - Function / Arbitrary

Waveform Generator

10MHz Sine & 4MHz Square waveform

Pulse, Ramp, Triangle, Noise, and DC waveforms

More than 25 Arbitrary Waveforms 10bits 100MSa/s, 4K points

Arbitrary waves AM, FM, and FSK modulation types Sweep and

Burst operation 10mVpp to 20Vpp amplitude range

Permanent 5 storage & recall for control panel setting

Waveform Creator Software for custom waveform generation

14 Antenna Training Setup with

Motorised Unit

with Motorised rotating unit and Plotting Software with 22

Antennas

Microconroller Based High Precision DC Stepper Motor..Automatic

Zero Point setting. Built-in DC Power Supply Instant Plotting of

radiation Pattern

15 Sampling & Reconstruction

Crystal controlled pulse generator

Demonstrates sampling and reconstructed as per Nyquist criterian

On-board synchronized analog signal generator Six, switch

selectable sampling frequencies

Sampling pulse duty-cycle selectable Internal/ External sampling

signal selectable

Separate sample and sample/hold outputs available

16 Delta, Adaptive Delta and Delta

Sigma Modulation/ Demodulation

Transmitter and Receiver on same board

Clock generation from crystal

Switch selectable sampling rates

Four on-board generators at 4 different

frequencies (synchronized)

Separate adjustable DC level

Selectable integrator gain setting (by switch

or control circuit)

On board 4th order Butterworth low pass filter

Unipolar to Bipolar converter on board

17 Data Formatting and Carrier

Modulation/ Transmitter

On-board Carrier generation circuit (Sine

waves synchronized to transmitter data)

On-board in phase and quadrate phase

carrier for QPSK modulation and DQPSK

Different data conditioning formats NRZ (L),

NRZ (M), RZ, Biphase (Manchester), Biphase

(Mark), AMI, RB, differentially encoded dibit

pair FSK, PSK, ASK ,QPSK & DQPSK carrier modulation

Variable carrier and modulation Off-Set

Variable carrier gain

On-board Unipolar to Bipolar conversion

On-board data inverter

18 Data Reformatting & Carrier

Demodulation Receiver

7 different data reconditioning formats NRZ

(M), RZ, AMI, RB Biphase (Manchester),

Biphase (Mark), differentially encoded dibit

to NRZ data ASK, FSK, PSK, DPSK ,QPSK

& DQPSK carrier demodulation

Output gives 2 Channels TDM multiplexed

data output

On - Board Biphase Clock recovery circuit

On - Board data squaring circuit and

differential decoder

On - Board Butterworth filters - 4th Order

19 Error Detection and

Correction-Cyclic Code

On-board Data and Code clock generation

On-board data generator,

BCD rotary switches for Data Selection LED Numeric display

Multiple data rate and code rate selection

Seven bit code for four bit running or static data

20 PCM Generation & Demodulation

using CODEC Chip

On-board clock generation

On-board signal generation

Audio interface for PCM coding and decoding

Low voltage requirement for operation

Variable sampling rate as per system clock used

21 4-Channel TDM-PCM Transmitter

and Receiver

VLSI based

Detailed study & analysis of respective topic.

Transmitter and Receiver on same board.

Variable sampling rates.

Clock generation from 8MHz crystal Oscillator.

On-board 4 different DDS signal generator.

On board 2nd order Butterworth low pass filter

with cut-off frequency of 5 KHz.

22 Digital Companding A-Law

and μ-Law

VLSI based




On-board DDS signal generators.

23 Understanding Noise Generator

and its applications

Study of different types of Noise and their frequency

spectrum

Additive White Gaussian Noise

Pseudo Random Noise

Practical implementation of mathematical equation :

y(t) = x(t) + n(t)

Study and analysis of eye pattern with and without

Noise.

24 PAM, PPM, PWM and Line

Coding Techniques

VLSI based



Variable sampling rates.


On-board DDS signal generators for five different

signals.

Selectable Ramp frequency (by push button or control

circuit)

On board 2nd order Butterworth low pass filter with

cut-off frequency of 5kHz for respective technique.

25

Elementary Fiber Optic On board function generator,AM-FM-PWM

Single Channel with experiments:

1) V-I Characteristics of LED

( E - O converter)

2) Characteristics of Photo Detector

modulation/demodulation ,built in dc power

supply, study of propagation & bending loss

in optical fiber &measurement of numerical

aperture

26 Optical Fiber Communication

Single Channel with experiments:

1) Measurement of Bit Error Rate *

2) Study of Eye Pattern *


( E - O converter)


5) Study of effect of EM on Fiber

Optic

Communication

On board function generator, AM-FM-PWM

modulation/demodulation, built in dc power

supply, study of propagation & bending loss

in optical fiber &measurement of numerical

aperture

27 Optical Fiber Communication - Dual

Channel & PC-PC Communication

Facility with experiments


( E - O converter)


On board function generator, AM-FM-PWM

modulation/demodulation ,built in dc power

& PC-PC Comm. Via RS232 ports

28 Multiplexer / De multiplexer -

Encoder / Decoder

On board sine wave & digital signal

generator16-channel time division

multiplexing and demultiplexing for digital

signal , 4- channel time division multiplexing

/demultiplexing for analog signal

29 Laser Fiber Optics

Experiments can be performed like:

characterization of a laser diode ,study of

ACC and APC modes of operation &

measurement of numerical aperture on

same board

30 LED Radiation Pattern On board transmitter and receiver with built

in DC power supply & study of LED

characteristic Sensitive, linear & accurate,

Functional blocks indicated on board mimic

High repeatability and reliability

31 LED 850/1300 nm Light

Source CW = -18 dB

Wavelength:850/1300nm

Power output: CW= -18.0dBm

32 Optical Power Meter

Measures two wavelengths(660 to 950 nm),

Measurement range :0 db to -60 db and

auto reading

33 Microwave Test Bench

(Gunn Based)

Setup Include :-

1.Coaxial wave guide adaptor

2.Detector mount

3.E-Plane band

4.Fixed attenuator 10 db

5.Fixed short

6.Frequency meter

7.Gunn Oscillator

8.Gunn power supply

9.H-Plane band

10.Isolator

11.Magic Tee

12.Matched Termination

13.Movable Short

14.Multi Hole Directional Coupler 10db

15.Pin Modulator

16.Pyramidal Horn

17.Slide Screw Tuner

18.Slotted Section

19.Standerd gain Horn antenna

20.Tunable Probe

21.Variable attenuator 20 db

22.VSWR Meter

23.Wave guide stand -04 No.s

25.Wave Guide cavity resonator

26.Smith chart

27.BNC To BNC Cable

28.Smith chart

29.Cooling Fan

30.Video Demo CD

31.Learning material CD

34 RADAR Trainer

RADAR receiving or detection.

>Experiment Unit that Contains:-

1.Transmitting frequency :10 GHz o/p power 10-15 mW

2.Operating voltage: 8.6 V ,Antenna : Horn

3.IF Output : Audio range

4.Alarm detected signal indication

5.Seven segment Display for object counting

>Suit case that contains:-

1.Audio cable for PC input, Din connector cable

2.Tripot stand ,Fan, Sliding platform, Different objects

3.Horn Antenna-trans-receiver unit, pendulum

4.Stand for moving the pendulum, Tuning forks

>Software CD

>Learning Material CD

35 15 MHz Oscilloscope with digital readout backlit LCD displays

(Volts/ Div, Time/Div), stable triggering up to

30MHz, maximum sweep speed200ns, built in

RS-232 interface and PC software, component

and continuity tester, gold plated BNC connectors.

36 1 MHz Function Generator with 50 MHz Frequency Counter (It has a wide

frequency range with LCD display for frequency,

output is up to 20Vpp, attenuation up to -60dB,

digital readout for Frequency)

37 Multimeter Hand Held 4 1/2 digit Measurement range Nos. 0 to 999.9 A+/-2%,

0 to 600V +/-1% AC V.

38 Multimeter Hand held 3 1/2, Measurement range : True RMS, : 4000

39 Multimeter Hand held 3 1/2, Measurement range : True RMS, : 20000

40 Transistor Characteristics Trainer

For CB, CC,and CE configuration with provision of measurement of all

the four parameters having built-in power supply and necessary

voltmeter and ammeter

41 Hartley and Colpitt Oscillator Trainer with

12V SMPS adapter Experiments; The

basic concepts and functioning of Hartley

and Colpitt Oscillator and their use in

generation of Sinusoidal waveform.

Hartley and Colpitt Oscillator Trainer with 12V SMPS adapter

Experiments; The basic concepts and functioning of Hartley and

Colpitt Oscillator and their use in generation of Sinusoidal

waveform.

42 Wein Bridge Oscillator Trainer with (+12

& -12V) inbuilt SMPS power supply

Experiment;

The basic concepts and functioning of Wein Bridge Oscillator and

their use in Generation of Sinusoidal waveform.

43 Astable, bistable and Monostable

Mutivibrator with inbuilt power supply

Experiment;

The fundamentals of Multi vibrators

Study the IC 555 as a monostable and

Astable multi vibrator

Astable , bistable and Monostable Mutivibrator

with inbuilt power supply Experiment;

The fundamentals of Multi vibrators Study the IC

555 as a monostable and Astable multi vibrator

44 kit to perform Experiments: Series kit to perform Experiments: Series positive clipper and negative

positive clipper and negative clipper

circuit Shunt positive and negative

clipper circuit Combination clipper

circuits with built in power supply, 1 KHz

sine wave generator

clipper circuit Shunt positive and negative clipper circuit

Combination clipper circuits with built in power supply, 1 KHz sine

wave generator

45 FET Characteristics Trainer with built in

power supply and digital voltmeter and

ammeter Experiments; Characteristics of

FET and to evaluate AC drain resistance,

transconductance, amplification factor

and DC drain Resistance.

FET Characteristics Trainer with built in power supply and digital

voltmeter and ammeter Experiments; Characteristics of FET and

to evaluate AC drain resistance, transconductance, amplification

factor and DC drain Resistance.

46 Transient Analysis of RC/RL Circuit Build

with +5V DC Supply and Signal

Generator. For study : Response of series

RC Circuit Response of series RL Circuit

Response of series RLC Circuit with SG

Response of series RL Circuit with SG

Transient Analysis of RC/RL Circuit Build with +5V DC Supply and

Signal Generator. For study : Response of series RC Circuit

Response of series RL Circuit Response of series RLC Circuit with

SG Response of series RL Circuit with SG

47 Transient Analysis of RLC Circuit

With built in Signal Generator for study Transient

response of series of RLC with TTL for under

damped, critical damped and over damped cases

Transient Analysis of RLC Circuit

With built in Signal Generator for study Transient response of

series of RLC with TTL for under damped, critical damped and

over damped cases

48 Experiments; Kit for study of FET

Amplifier

constant power supply 12 volts

Experiments; Kit for study of FET

Amplifier

49 Power and Differential Amplifier Trainer variable power supply 0 to 1 volts, sine wave generator 800 Hz to

8 kHz, voltage 0 to 5 Vpp Experiments: study of power and

differential amplifier

50 Kit for Experiments: study of BJT

amplifier AND Emitter follower

With power supply 12 volts and 5 volts, Inbuilt sine wave

generator (10Hz-100KHz) voltage 0 to 6 Vpp

51 Lissajous Pattern Trainer with (+5V)

SMPS adapter Experiments; Study-

AND,OR,NOT,NAND, NOR,X-OR and X-

NOR Gates Verification of Truth Table of

Logic Gates mentioned above. Logic

Levels : +5 V and 0V

Lissajous Pattern Trainer with (+5V) SMPS adapter Experiments;

Study- AND,OR,NOT,NAND, NOR,X-OR and X-NOR Gates

Verification of Truth Table of Logic Gates mentioned above. Logic

Levels : +5 V and 0V

52 Transistor Analyzer

Single module covers important transistor tests On-board Curve

Tracer circuit Comprehensive test circuit diagrams shown over

mimic, On-board Micro-ammeter for low current measurement,

On board NPN /PNP selection for each test, Control knobs for

amplitude, number of base steps & sweep frequency select

53 8085 Microprocessor Trainer Kit 8085 Microprocessor Trainer Kit

54 8086 Microprocessor Trainer Kit 8086 Microprocessor Trainer Kit

55 Microcontroller Developer Trainer Kit

8051 family

Microcontroller Developer Trainer Kit 8051 family

56 Trainer Board of B/W Television I F and

frequency response section

Trainer Board of B/W Television I F and frequency response

section

57 Trainer Kit CTV Chroma section and

colour sync. Circuit

Trainer Kit CTV Chroma section and colour sync. Circuit

58 Demonstration of Dipole and Yagi Uda

TV antenna

Demonstration of TV antenna with parameter such as directivity,

selectivity, field strength and radiation pattern measurement

accessories

59 Video Recording and processing system

set

Video Recording and processing system set

60 FM Radio Receiver demonstration Board FM Radio Receiver demonstration Board with parameter

measurement options

61 AM Radio Receiver demonstration Board AM Radio Receiver demonstration Board with parameter

measurement options

DST-06- List of Mining Engg. Equipments


1. Amphibole group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be

label in transparent plastic tray with top cover each sample

should be free of any weathering

2. Bomb calorimeter for Calorific value

of coal

For laboratory purposes;

3. Breath Alcohol Detector For determination of alcohol level amongst miners

4. Crossing Point and Ignition

Temperature Apparatus DGMS Approved Fabricated

5. Design Software Auto-cad - Latest Education Version with all

Modules

6. Desk top Computers for graphical

design

Processor 3rd Generation Intel® Core™ i5-3450

Processor (3.10 GHz, 6MB Cache, with Turbo Boost Technology

2.0)

Operating System Windows® 7 Home Premium SP1 64

bit (English)

Memory3

8GB3 Dual Channel DDR3 SDRAM at 1600MHz

Hard Drive 1TB SATA 3.0Gb/s Hard Drive with Native

Command Queuing

Video Card 1GB GDDR5 NVIDIA® GeForce® GT 545

Optical Drive Slot-Loading Dual Layer DVD Burner (DVD+-

RW, CD-RW)

Monitor 26” LCD

7. Diamond Crossing Model for demonstration for laboratory purposes

8. Drill Bits of Different Types For demonstration purposes in laboratory

9. Drill Rod of turbine and Diamond

Section

For demonstration purposes in laboratory

10. Feldspar group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be



11. Feldspathoid group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be



12. Flame safety lamp. GL-7 and GL-50; DGMS Approved

13. Flat Jack Apparatus The equipment should permit determination of deformability

characteristics of rock mass using the method suggested by the

International Society of Rock Mechanics (ISRM). It must

consists of hydraulic pumps, two flat jacks, extensometers,

pressure gauges and assembly required for simultaneous

loading of two areas across the drift.

14. Geologist Hammer Pick Axe type Geological Hammer with following

specification:-

a) It should be in one single piece of tempered stainless steel

without any welding or joint.

b) Hammer head with one end pointed axe type and other

end blunt, square in cross section.

c) Hammer head will be nearly 19 cm (7.5”) long.

d) Total weight of the hammer will be nearly 900 gms.

e) 30 cm. long Handle with Nylon-Vinyl deep cushion grip.

15. GM counter GM Tube: Metal wall (Fe, Cr alloy) ~90 Mg/cm2 thick, neon

filled, halogen quenched

High Voltage Requirements: +400 to +500 V at ~2 mA, +550 V

maximum

Plateau: ~440 V to 500 V, ~0.5%/V

Dead Time: ~40 ms

Signal Output: +5 V pulse ~25 ms wide

Gamma Sensitivity: ~9.0 x 10-7 rad/pulse

Gamma Energy Response: ±10% from 70 keV to 2.1 MeV.

The response below 70 keV falls rapidly.

Angular Response: 0° to 90° end on, ±12% CS137; 0° to 90°

side on:±5% Co60

Neutron Sensitivity: Less than 1 % of gamma sensitivity for

neutrons @2 MeV

Proton Shielding: Counter wall will stop ~22 MeV protons

Signal Connector: Mates with BNC UG 260B/U or equal

Signal Cable: Any

High Voltage Connector: Mates with UG932A/U or equal

(SHV upon request)

High Voltage Cable: RG59/U or equal

Construction: Aluminum, waterproof detector housing on

end of 10.5 inch (26.7 cm) long, 0.25 inch (O.64 cm) diameter

shaft.

Housing Diameter: GM-1-0.53 inch(l.35 cm); GM-lS-0.75 inch

(1.9 cm)

Overall Size and Weight: Length including

16. GPS receiver with antenna Accuracy: Better than 10 m

Autonomous accuracy

Memory : 32 MB and above with CCMCIA / Memory card and

card reader Communication : RS 232/USB port Temperature

Range : - 100C - + 500C

Weight: Less than 1 Kg Battery

Life: Minimum 8 hrs

Internal Battery : Rechargeable / 1400 MHA & More

Charging voltage : 200 volts

PC compatibility: Compatible to window XP operating system

with multimedia

Software : 1 GPS data processing, Software-standard 2,

Mapping software with GIS

Channels: Minimum 8 Channels

Field Ruggedness Technical document Accessories : PC

interface cable carrying

17. Gravimetric Dust Sampler DGMS Approved

18. Inflammable gas testing arrangement

with chamber

A gas testing chamber for flame safety lamp and gas chamber,

lpg gas supply system to maintain the Safety Lamp and Gas

Chamber.

1 No. Methane Gas Testing Chamber having robust

construction with teak wood consisting of clear glass in all four

sides to have a clear view for 3-4 trainees at a time.

Length - 12 inch Breadth - 12 inch Height - 18

inch

01 No. GAS CAP INDICATOR BOX (WOODEN) – made of 1 inch

thick special quality teak wood.

Length - 18 inch Breadth- 6 inch Height - 9

inch

(Rubber Buffer- 4 Nos. to be attached with the bottom of

wooden box)

Front portion of the above Gas Cap Indicator Box to be fitted

with 6 mm thickness of special type glass comprising 8 Nos.

of flame height of Gas Cap as indicated in the printed literature.

The following are provided along with the Chamber:-

LP Gas Cylinder, Gas Pipe, Regulator, Gas Socket along with

1 No. Velox GL7 Gas Testing Flame Safety Lamp (DGMS

approved)

A best quality of one set complete tube light to be fitted inside

the chamber for illumination of the length ‘Mode Gas Cap’. One

tube light is also to be fitted inside the box. A complete electric

fitting both inside and outside so also back side of the wooden

box including a plug point line. High glossy polish to be coated

on the total outside cover area and mat polish inside the area

of the wooden box

19. Jack Hammer Drill Model for demonstration purposes in mining laboratory

20. Load cell For measuring load on prop up to 25 tons.

21. Magnetic un-locker Magnetic Un-locker for opening lock of Flam safety Lamp

22. Mica group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be



23. Mineral Specimen tray 5”x5’x4” size. made of transparent plastic in form of box.

24. Model of Centrifugal pump For demonstration purposes in laboratory

25. Model of coal cutting m/c Model of continuous miner for demonstration purposes in

laboratory

26. Model of Face pump For demonstration purposes in laboratory

27. Model of Reciprocating pump For demonstration purposes in laboratory

28. MSA CO Detector, MSA CO Detector

Tube

DGMS Approved

29. MSA D-6 Digital Methanometer with

extendable probe

MSA D-6 Digital Methanometer with extendable probe; DGMS

Approved

30. Non – silicate group mineral

Corundum, Spinel, Calcite, Dolomite,

Magnesite

Hand specimen size 2”x3” or 3”x 4”.each specimen must be



31. Plant fossils

Glassopteris, Gangamopteris,

Vertebrariptilophyllum

Each fossils must be kept in transparent tray with proper label

32. Point Load Testing Apparatus Point Load Test Apparatus of load frame 60 kN capacity with a

hydraulic loading ram actuated by a hand pump. The frame

may be adjustable to allow for testing samples up to

102 mm dia. A ruler assembled on the frame allows for direct

measurement of the distance between the conical platens

before and after the test. The compression load is measured by

a pressure transducer with an advanced digital display unit

assuring the best accuracy and resistance to the failure shocks.

The machine, fitted with the set of lower and upper platen of at

least 52 mm dia with spherical seat for compression tests, can

http://cooper.co.uk/glossary/kn/

http://cooper.co.uk/glossary/mm/


also be used for compression tests on small cores or cylindrical

specimens. The apparatus is contained in an easily

transportable case.

33. Portable Dust Sampler DGMS Approved

34. Pp magnetometer

35. Precise Sound Level Meter

36. Pulmoter

Dragger or MSA Make, DGMS

Approved

Dragger or MSA Make, DGMS Approved

37. Pyroxene group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be



38. Quartz group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be



39. Seismic timer

40. Seismic vibration meter

41. Shaft Correlation equipment For demonstration purposes in Mining laboratory

42. Silica group mineral set Hand specimen size 2”x3” or 3”x 4”.each specimen must be

label in transparent plastic tray with top cover.each sample


43. Strain Gauge

44. Surpac Software Latest version for 2d and 3d surveying application

45. Telescopic Leveling staff

4M

Telescopic & 5mm least count

vertical reading

46. Thermo Hygrograph for recoding

temp. And humidity

47. Universal Testing Machine 400 KN Load : Maximum capacity of Load at least 40 TON / 400KN.

Accuracy: ±1% of the applied force.

Least Count : 0.04 KN

Measuring Range : 0-400 KN

Resolution of piston movement : 0.1 mm

Clearance between column : 500 mm

Ram stroke : 200 mm

Straining / Piston Speed at no Load : 0-15 mm

Power of connected load : 2.5 HP

Dimensions : 2032 x 600 x 1960 mm

Weight : 1600 kg (approx)

48. Whirling Hygrometer DGMS Approved

49. Wire Rope Section of various types of

Ropes

For demonstration purposes in Mining laboratory

50. Compression Testing Machine

2000 KN Capacity

Ram Travel:- 50mm

Daylight Clearance:-325mm (Minimum)

Horizontal Clearance:-300mm

Platen size:-Minimum Dia-220mm

220V/50Hz AC Supply

51. Proving Ring

2000 KN Capacity with loading Platens conforming IS-4169

Sensitivity:-5N per division, Certified by NPL/NABL or Other

approving body.

52. Exploration seismograph

24 channels geophones with

software and all accessories

A/D Conversion: 24 bit result using Crystal Semiconductor

sigma-delta converters and Geometrics proprietary

oversampling.

Dynamic Range: 144 dB (system), 110 dB (instantaneous,

measured) at 2ms, 24dB.

Distortion: 0.0005% @ 2 ms, 1.75 to 208 Hz.

Bandwidth: 1.75 Hz to 20 kHz. Low corner frequency option

available.

Common Mode Rejection: > -100 dB at <=100 Hz, 36 dB.

Crosstalk: -125 dB at 23.5 Hz, 24 dB, 2 ms.

Noise Floor: 0.2uV, RFI at 2 ms, 36 dB, 1.75 to 208 Hz.

Stacking Trigger Accuracy: 1/32 of sample interval.

Maximum Input Signal: 2.8 VPP.

Input Impedance: 20 kohm, 0.02 uf.

Preamplifier Gains: SGOS software enables selectable gain pair

of either 24 or 36 dB. MGOSsoftware selection between jumper

gain pair 12 and 24 dB, gain pair 24 and 36 dB, or 0dB.

Anti-alias Filters: -3 dB at 83% of Nyquist frequency, down 90

dB.

Pre-trigger Data: Up to 4,096 Samples. Optional event

detection software enables system for earthquake, vibration

monitoring.

Sample Interval: 0.02, 0.03125, 0.0625, 0.125, 0.25, 0.5, 1.0,

2.0, 4.0, 8.0, 16.0 ms.

Record Length: 16,000 samples standard, 64,000 samples

optional 2

Delay: 0 to 9999 ms in 1 ms steps.

Data Transmission: Uses reliable Ethernet connections and

requires no custom transmission software. Interfaces directly

with Windows OS.

Auxiliary Channels: All Geode channels can be programmed as

either AUX or DATA.

Instrument Tests: Optional built-in analog testing available.

Tests provided: noise, crosstalk, total harmonic distortion, gain

similarity, gain accuracy, common-mode rejection, trigger

accuracy

Acquisition and Display Filters:

Low Cut: OUT, 10, 15, 25, 35, 50, 70, 100, 140, 200, 280, 400

Hz, 24 or 48 dB/octave, Butterworth.

Notch: 50, 60, 150, 180 Hz and OUT, with the 50 dB rejection

bandwidth 2% of center frequency.

High Cut: OUT, 250, 500 or 1000 Hz, 24 or 48 dB/octave.

Line Testing: Real time noise monitor displays real-time output

from geophones. Optional geophone pulse test helps identify

bad geophones and shorted or broken cables.

Data Storage: Stores data on local hard drive,

local RAID, or NAS. Tape support available under Windows XP.

Triggering: Positive, negative or contact closure, software

adjustable threshold.

Data Formats: SEG-2 standard with SGOS. SEG-D and SEG-Y

available. 2

Power: Requires 12V external battery. Uses 0.65 W/channel

during acquisition, sleep mode reduces power consumption by

70% while in standby.

Plotters: Drives most Windows-compatible printers and

plotters

Environmental: -30 to 75 degrees C. Waterproof and

submersible. Withstands a 1 m drop onto concrete on 6 sides

and 8 corners.

Operating System: Windows XP/W2K/ME/98/NT/Vista. An

older, limited feature version of the software is available for 95

53. Global Positioning System Accuracy: Better than 10 m autonomous accuracy

· Memory:32 MB and above with CCMCIA/Memory card and

card reader· Communication: RS 232/USB

port Temperature Range: -100C - +500C

· Weight: Less than 1 Kg · Battery Life: Minimum 8 hrs.

· Internal Battery: Rechargeable/1400 MHA & More

· Charging Voltage: 200 volts

· PC compatibility: Compatible to Window XP operating system

with multimedia

· Software: 1. GPS data processing software-standard. 2.

Mapping software with GIS Channels: Minimum 8 channels

· Field Ruggedness

· Technical document

· Accessories: PC interface cable, carrying

54. Bowens reaction table All rocks must be kept in wooden box, frame according to

Bowens reaction principle. Wooden box must be covered with

4 mm transparent fiber plate. Facility to hang on wall.

55. IUGS/ Double triangle classification

of ignous rock

All rocks must be kept in wooden box, frame according to

IUGS/ Double triangle classification. Wooden box must be

covered with 4 mm transparent fiber plate. Facility to hang on

wall.

56. DIGITAL

(ELECTRONIC)

THEODOLITE

Angular Accuracy : 10” (Second) or

better.

Least Count : 10” (Second) or less

Telescope Magnification : 30 X,

Telescope Image : Upright/Erect,

Shortest Focusing Distance : 1.7 M or

Less., Angle Measurement :

Continuous

Compensator : Dual Axis., Display :

L.C.D.

Plummet : Laser/Optical, Power

Supply : 2 nos. NIMH, 6V. Rechargeable,

internal and 1 no.

External Batteries

per Unit Set., Charger : 1 no. suitable

quick charger for internal and

external batteries with 2 nos.

Charging cable/Cord and adaptor per

unit set. Operating Temp. : (-) 200 C

to 500 C

Telescopic Tripod (Wooden) : 1 per

Unit set with Canvas carrying bag

with shoulder strap.

57. Total Station

Angular measurement Standard

deviation per ISO17123-3, 1 σ 1) 0.5“

(0.15 mgon) Units of measurement

360° sexagesimal, 400 gon 360°

decimal, 6400 mil Display 0.01

mgon; 0.1“, 0.00001°, (smallest

selectable unit) 0.00001 mil

Automatic reference to the horizon (2-

axis liquid compensator) Working

range, longitudinal/lateral 3' (0.055

gon) Setting accuracy ≤ 0.3“ (0.1

mgon) Displays LCD (liquid crystal

display) 8 rows of 35 characters each

6 status fields Data storage and

interfaces PCMCIA memory card

RS232 programmable interface Motor

and fine drives Fine drives

Coarse/fine, motorized, infinite, slip

coupling Motor Speed of rotation 45

°/s (50 gon/s) Positioning accuracy

0.8” (0.2 mgon)

Touch Screen Operation Facility

58. Rock Hand Specimen Basalt gobbro, Norites, Trctolites, Anorthosite, Pyroxenites,

Diorites Monzonites, Syenites, Granites, Syenite, granites

granodiorites, tonalities, Peridotites, sandstone, limestone,

greywacke, arkosic sandstone lithic sandstone, dolomite, chert,

porcellanite, glauconite, ironstones, slates, phyllites, schists,

gneiss, granulites, amphibolites, quartirites, Marbles, eclogites,

augen gneisses.

59. Core Drilling Machine

Core cutting- core drilling machine (electrically operated)Suitable to cut / Drill cores of Rocks, Stones, Tiles concrete or the similar material. Core cutting machines (at least 100 mm dia) with 2 core bit (4 inch, 6inch) The machine is suitable for care samples of size upto 150mm diameter The base frame is also fitted with wheels for ease of transportation. Drill Speeds : 900 RPM for soft samples and 350 RPM for hard samples.

Suitable for 220 volts AC, Single Phase Accessories: Thin wall diamond bit - 1 Core Barrel - 1

60. Rock Cutting, Grinding, Polishing, Ore

Mounting

Machine for Geological samples

preparation with

Accessories, stand and trays.

Cutting disc with multiple speeds;

automatic multiplate grinder; Multi

sample polishing with different

motions and variable speed;

Mounting system with proportional

temperature controller with different

mould assembly and accessories

61. Self-Rescuer DGMS Approved

62. Velometer DGMS Approved

63. Digital Auto Level Electronic measurement

Invar precision bar code staff . . . . . . . 0.3 mm (0.001 ft)

Standard bar code staff. . . . . . 1.0 mm (0.004 ft)

Visual measurement . . . . . . . 1.5 mm (0.005 ft)

Distance measurement . . . . . . . with a 20 m (65.62 ft) sighting

distance

Invar precision bar code staff . . . . . . . 20 mm (0.066 ft)

Standard bar code staff. . . . . . 25 mm (0.082 ft)

Visual measurements. . . . . . . . . . . . . 0.2 m (0.656 ft)

Electronic measurement

Invar precision bar code staff . . . . . . . 0.7 mm (0.002 ft)

Standard bar code staff. . . . . . . . . . . . . 1.3 mm (0.004 ft)

Visual measurement. . . . . . . . 2.0 mm (0.007 ft)

Distance measurement . . . . . . . with a 20 m (65.62 ft) sighting

distance

Invar precision bar code staff . . . . . . . 25 mm (0.082 ft)

Standard bar code staff. . . . . . . . . . . . . 30 mm (0.098 ft)

Visual measurement. . . . . . . 0.3 m (0.984 ft)

Range

Electronic measurement. . . . . . 1.5 m–100 m (4.92 ft–328.08 ft)

Visual measurement . . . . . . . from 1.3 m (4.265 ft)

Electronic Measurement


Resolution height measurement. . . . . 0.01 mm / 0.0001 ft /

0.0001 in

Resolution distance measurement . . . . . . . . 1 mm (0.003 ft)

Measurement time. . . . . . . 3 s


Resolution height measurement. . . . . . . . 0.1 mm / 0.001 ft /

0.001 in

Resolution distance measurement . . . . . . . . 10 mm (0.033 ft)

Measurement time. . . . . . . . . . 2 s

Horizontal Circle

Type of graduation . . . . . . . 400 grads and 360 deg

Graduation interval. . . . . . . . . . . . . . 1 grad and 1deg

Estimation to . . . . . . . . . . . . 0.1 grad and 0.1 deg

Measurement Programs

Standard programs . . . . . . . . Single measurement with and

without stationing, stakeout, line leveling with intermediate

sight and stakeout, line adjustment

Levelingmethods¹. . . . . . . . BF, BFFB, BFBF, BBFF, FBBF

aBF, aBFFB, aBFBF, aBBFF, aFBBF

ENVIRONMENTAL

Operating temperature. . . . . . –20 °C to +50 °C (–4 °F to 122 °F)

Dust- and waterproofing. . . . . . . . . . . . . . . . . . . IP55

GENERAL SPECIFICATION

Telescope

Aperture. . . . . . 40 mm (0.131 ft)

Field of view at 100 m. . . . . . . . 2.2 m (7.217 ft)

Electronic measurement field . . . . . . . 0.3 m (0.984 ft)

Magnification

Compensator

Inclination range. . . . . . . . . . . . . . . . . . ±15'

Setting accuracy

Circular level. . . . . . . 8'/2 mm with Illumination

Display. . . . Graphical, 240 x 160 pixels, monochrome with

illumination

Keyboard. . . . 19-key alpha-numeric and 4-way arrow key for

navigation

Recording

Internal memory . . . . . . up to 30 000 data lines

External memory. . . . . . . . USB Flash Drive support

Data transfer . . . . . USB Interface for data transfer between

(means two way communication)

Real-time clock and temperature sensor

0.3 mm per km. . . . . Recording of time or temperature

0.7 mm per km. . . . . . . N.A.

Power supply

Internal battery. . . . . . . . . . . . . . . . . . . . . . . . . . . Li-Ion, 7.4 V /

2.4 Ah

Operating time. . . . . . . . 3 days working time without

illumination

Weight (including battery). . . . . . . 3.5 kg (7.72 lb)

64. Porosity Test Apparatus Fabricated as per International

Society of Rock mechanics Standards

65. Model of Continuous Miner Fibre or Plastic Working Model

battery Driven or AC Supply

66. Working Model of

Dumper Truck( Rear

Tipping, Side Tipping

and Bottom Discharge

Type

Fibre or Plastic Working Model

67. Working Model of Shovel Fibre or Plastic Working Model

68. Working Model Walking Dragline Fibre or Plastic Working Model

battery Driven or AC Supply

69.

Multigas detector

For detection of CO, O2, H2S and Explosive gas e.g.CH4

Detecting Range: 0-100%

LCD Digital

Alarm Indication (Long Extendable Probe)

70. Anchorage Testing m/c

For testing for roof bolts anchorage strength in underground

mines for a height roof of up to 5 meters.

Weight:

Maximum 20 Kgs for 12 T Capacities. Equipment can be accommodated in a Bog/Box.

Hoses: 6 meters, Working Pressure-700 Bar, Testing Pressure Bar, Burst Pressure: 2800 Bar; Make: Thermo Plastic.

Bridge: To support in between Roof & ATM Jack, Provide with no of slots for better observation, along with bearing plates on both the sides.

Indicator Gauge: Show Hydraulic Pressure directly calibrated to tones with a least count of 0.5 tons to 1 tones, along with gauge.

Hydraulic Oil: Recommended one Like Indian Oil SS46/48. CMRI Test

Certificate for Anchorage testing Machine and with Operation

& Maintenance manuals provided.

71. Lux Meter Intrinsically Safe DGMS Approved

72. Strain Gauge Key Features Measurement of 120 ohm resistive strain gauges in

quarter bridge configuration Liquid Crystal Display giving micro strain units with

a range of +/- 20,000 Rechargeable Nickel-Metal Hydride battery Ability to read up to 18 strain gauges automatically Hand-held graphite filled glass fiber antistatic case

with shoulder strap

Specification Display: high visibility 8 character numeric Liquid

Crystal Display.

Power pack: 12v NiMH rechargeable batteries providing over 8 hours continuous use.

Temperature Range: 0 to +50°C operating temperature; -20 to + 50° C transport and storage temperature.

Excitation Voltage: 2.5V. Dimensions: 270 x 240 x 180mm. Weight: 3.6kg.

Accessories -Included with the SM02 unit is:

Multi-voltage a.c. “intelligent” battery charger; User manual and plasticized instruction sheet; USB cable and drivers for PC interface; and Exbolt for Windows software package including

manual. 73. Surpac Vision Geo

Modelling Software

Latest Education Version with all

Modules (Lite, Topographic, Mining, Geology, Cadastral model)

74. Noise Level Meter LCD digital display, Analog bar indicator,Rs232c interface

Computer record graph software Backlight Low power

indication.

75. Hardness Pencil for moh’s scale of

hardness

Made of Sharp edge of minerals having hardness from 1 to 10

in form of pencil.

76. Precise Micro-optic

Theodolite

Magnification : 30 X or better

Telescope Image : Erect, Clear

Objective : 42 mm or better. Shortest

focusing distance : 1.5 or

less. Horizontal/Vertical Circles

reading : Digital, Least count : 20” or

better Plummet : Optical. Working

range temperature : (-) 200 C to 500

C, Multiplication factor : 100

Additive constant : 0, Clamping &

Tangent screws : Coaxial. Sensitivity

of Levels: (a) Circular Level : 10’/2

mm or better Plate Level : 40”/2 mm

or better, Other accessories : Tubular

Compass, Plumbob Set, Tools Kit,

Lens Cap, Vinyl Cover etc.

77. Polarized light petrological

microscope

Main Body - Optical System:

CFI60 infinity

Main Body -Illumination:

12V-50W halogen lamp; 12V-50W DC transformer built-in;

Diascopic/Episcopic illumination changeover switch; Fly-eye

http://www.nikoninstruments.com/Information-Center/Illumination

lens; NCB11, ND8 filters built-in; 12V-100W type optional

(requires external power supply)

Main Body - Focusing:

Coaxial coarse/fine focus knob; Focus stroke: 30mm; Coarse:

14mm per rotation; Fine: 0.1mm; Minimum reading: in 1µm

increments

Eyepiece:

10x (F.O.V. 22mm), CM type with crosshair and micrometer

scale

Eyepiece Tube:

P-TT Trinocular Tube for polarizing microscopy; P-TB Binocular

Tube for polarizing microscopy

Intermediate Tube:

Built-in focusable Bertrand lens removable from optical path;

Switchable Conoscopic/Orthoscopic observations; Analyzer

built-in; Plate/compensator slot

Analyzer:

360° rotary dial; Minimum reading angle 0.1°

Nosepiece:

Reversed centering quintuple nosepiece (detachable); DIN slot

Stage:

Top-grade dedicated circular graduated stage. Rotatable 360°

horizontally; can be fixed at a specific position. Graduated 360°

(in 1° increments); Click stops each 45°. Attachable mechanical

stage: 35 x 25mm travel; vernier 0.1mm

Condenser:

Dedicated strain-free swing-out type; P Achromat N.A. 0.9

Polarizer:

Fixed to the bottom of the condenser holder; Scale

Objectives:

CFI P Achromat 4x, 10x, 20x, 40x, 100x, CFI LU Plan Fluor Epi P

5x, 10x, 20x, 50x,100x

Episcopic Illuminator:

LV-UEPI Universal Epi-illuminator accommodates a 12V-50W

illumination transformer. 12V-100W type optional.(requires

external power supply)

http://www.nikoninstruments.com/Information-Center/Focus

http://www.nikoninstruments.com/Information-Center/Focus

http://www.nikoninstruments.com/Information-Center/Polarizing

Compensators:

Standard 1/4 λ & tint plate, quartz wedge or Senarmont

compensator can be inserted into intermediate tube slot

Power Consumption:

1.2A/75W

78. Laser distance meter 1. Measuring accuracy range +_ 1.5 mm to Capable to measure distance up to 100 mm.

2. Measuring units m, ft, in 3. Tilt measuring range +_ 45 or 360

0

4. With software and stand (Tripod) and all accessories with area, volume measurement, Pythagoras functions.

79. Hardness Box Minerals having hardness 1 – 10 as scaled by moh’s

80. Model for Endless Rope Haulage

Layout:

Model shows the layout of an over –rope type endless rope

haulage at a level haulage road in coal gallery. It comprises coal

pillars, a manhole, haulage signal wires, two tracks-one for full

& one for empty tubs, Clifton pulley (showing its constructional

details) operated by a handle to move the endless haulage

rope, guide pulley, return pulley mounted on high frame to

make this an over-rope type haulage, rope tension

arrangement by tension bogie & weight, lashing chains and

four coal tubs. There are sliding transparent sheet covered

windows at gallery roof and big window at side of gallery

covered by transparent sheet to show interior details and to

operate the model, Model labeled by paint.

Size: 2.4mx52cmxheight 34 cm approx.

81. Protodykanov Index Apparatus

Fabricated as per International

Society of Rock Mechanics Standard

Model-1

Universal Testing Machine 400 KN

Load: Maximum capacity of Load at least 40 TON/ 400 KN. Accuracy: ±1% of the applied force. Least Count: 0.04 KN Measuring Range : 0- 400 KN Resolution of piston movement: 0.1mm Clearance between column: 500mm Ram stroke: 200 mm Straining/Piston Speed at no Load: 0-150mm Power of connected load: 2.5HP Dimensions: 2032 x 600 x 1960mm Weight: 1600 Kg (approx.)

82. Protodykanov Index Apparatus

Fabricated as per International

Society of Rock Mechanics Standard

Model-2

400/440V, 50Hz Three Phase A.C Supply 1.5 H.P with hydraulic

system

Designed to perform variety of tests like tension, compression,

etc. on metallic materials.

Continuous roll autographic load recorder

Provision for computer with user friendly software

Auto detection and switching off provision in case of over load,

over travel and specimen break.

Analogue and computerized control panel

Capacity: 400KN

Max. Range: 10-200KN ±0.1 KN

Min. Range: 0-20KN ±0.01KN

Maximum tensile clearance at full : (50-700 mm)

decedent piston position

Distance between columns: 500 mm.

Piston stroke: approx 200 mm.

Max Clearance for compression rest : 0-700(mm)

Max. Straining speed at No. Load : 150(mm / min)

Pair of compression plates dia 120 mm

For Tension Test Jaws:

Round specimen dia 10-20 mm

Round specimen dia 20-30 mm

Flat specimen thickness 0-10 mm

Flat specimen thickness 10-20 mm

Max. width for flat specimen 50 mm

For Transverse Test:

Adjustable Roller Support of width approx. 150 mm

Adjustable Roller Support of dia. approx. 30 mm

With max adjustable clearance approx. 500 mm

RS232 Serial Port/Data Cable

Standard Accessories

Optional Accessories:

Extensometer

Load rate Control

Load rate stabilizers

Flat Belt test

Bolt nut and Washer test

Single and double shear test

Tensile test for shouldered and threaded

Bend Re-bend test

83. Methanometer MSA D-6 Digital Methanometer with extendable probe

84. Zoom binocular microscope with

imaging set up for study of rock

Optical System:

Parallel Optical Zoom System

Zoom Range:

0.75x to 11.25x

Zoom Ratio:

15:1

Total Magnification:

3.75x to 540x depending on eyepiece and objective used (5.6x

http://www.nikoninstruments.com/Information-Center/Magnification

to 506x when coaxial episcopic illuminator is attached)

Distance between Optical Axes:

22mm

Zooming Knob:

Coaxial control knobs on both sides, with click stops

(on/off), magnification indicated

Aperture Diaphragm:

Incorporated

Objective Lenses:

HR Plan Apo 0.5x; HR Plan Apo 1x; HR Plan Apo 1.6x; P-Plan

Apo 0.5x; ED Plan 0.75x; P-Plan Apo 1x; P-ED Plan 1.5x; P-ED

Plan 2x

Objective Mounting:

Screw Mounting to Zoom Body: M58 x 1.25 internal diameter

to accept accessories: M55 x 0.75 external diameter: diameter

60mm; Note: Except HR Plan Apo 1.6x

Eyepiece Tubes:

Binocular Eyepiece Tube, 20° Inclination, Interpupilary

Distance: 48-75mm; Low Eyelevel Eyepiece Tube, 20°

Inclination, Interpupilary Distance: 48-75mm; Tilting Binocular

Eyepiece Tube, 0 - 30° Inclination, Interpupilary Distance: 48-

75mm

Eyepiece Tube Mounting:

54mm diameter; 60° round dovetail

Eyepieces with Diopter Adjustment:

C-W 10x (F.N. 22); C-W 15x (F.N.16); C-W 20x (F.N. 12.5); C-W

30x (F.N. 7)

Focusing Mount:

P-FMD Focusing Mount D, Stroke: 65mm; Diameter of opening

for post: 32mm

Stands:

C-PS Plain Focusing Stand; C-PSC Compact Plain Focusing Stand;

C-DS Diascopic Stand S; C-PS160 Plain Stand; C-DSS Advanced

Diascopic Stand; C-DSD Enhanced OCC (Oblique

Coherent Contrast) Stand; C-BD Bright field/Dark field Diascopic

Stand; C-US-1 Universal Table Clamp Stand 1; C-US-2 Universal

Table Stand 2; US-3 Universal Table Stand; P-THS Teaching

Head Stand (requires P-THSS Teaching Bridge)

http://www.nikoninstruments.com/Information-Center/Magnification

http://www.nikoninstruments.com/Information-Center/Contrast

http://www.nikoninstruments.com/Information-Center/Brightfield2

Illumination Systems:

P-FLA2 FL Epi Fluorescence Attachment with 4 position slider

for up to 3 fluorescence filter sets with one open position,

optional photo/video port can be added to integrated beam

splitter; P-ICI2 Coaxial Episcopic Illuminator (12V/100W

halogen) (Intermediate magnification 1.5x); 150W High

Intensity Fiber Optic Light Source, single and double gooseneck

light pipes and ring lights available; 30W Fiber Optic Light

Source (single gooseneck light pipe included), double

gooseneck light pipes and ring lights available; G-LS 6V/10W

Illuminator; G-LS 6V/10W Illuminator with articulated arm;

6V/20W Illuminator with articulated arm; C-Fluorescent Ring

Illuminator with built-in transformer, intensity light switch; Epi-

Fluorescence Illuminator with optional photo tube

Beam splitters:

P-IBSS Single Port Beam splitter, Split: 100/100:0 100/50:50; P-

IBSD Dual Port Beam splitter, Split: 100/100:0/0, 50/50:50/50,

0/100:100/0

P-THSS Teaching Bridge:

Side-by-side (requires dedicated teaching bridge stand) (P-IDT

Drawing Tube optional

High resolution Image capturing attachment and image display

on computer screen

85. Multimedia Kits / Training Videos for

various Mining methods, safety

precautions, blasting etc

PAL DVD / VCD of 30 to 40 minutes duration with Broadcast

resolution

86. Brunton Compass Pocket Compass : DQL – 8, Precision of plate level : 20' ± 5' / 2

(mm), Precision of circular level : 30'+_5' / 2 (mm), Reading

error : < 0.5” , Min. Graduation : 1”, Damping time : < 15”

87. Digital Brunton Compass Pocket Compass : DQL – 8, Precision of plate level : 20' ± 5' / 2

(mm), Precision of circular level : 30'+_5' / 2 (mm), Reading

error : < 0.5” , Min. Graduation : 1”, Damping time : < 15”

88. Point Load Testing Apparatus

Point Load Test Apparatus of load frame 60 kN capacity with a

hydraulic loading ram actuated by a hand pump. The frame

may be adjustable to allow for testing samples up to

102 mm dia. A ruler assembled on the frame allows for direct

measurement of the distance between the conical platens

before and after the test. The compression load is measured by

a pressure transducer with an advanced digital display unit

assuring the best accuracy and resistance to the failure shocks.

The machine, fitted with the set of lower and upper platen of at

least 52 mm diameter with spherical seat for compression

http://www.nikoninstruments.com/Information-Center/Illumination

http://www.nikoninstruments.com/Information-Center/Fluorescence

http://www.nikoninstruments.com/Information-Center/Fluorescence

http://www.nikoninstruments.com/Information-Center/Fluorescence2

http://cooper.co.uk/glossary/kn/



tests, can also be used for compression tests on small cores or

cylindrical specimens. The apparatus is contained in an easily

transportable case.

89. Automatic level Reflector type, accuracy- 0.01%, Range in Km, with all

supporting accessories and coverings.

90. High volume sampler

model – II

Sampling principle: Impactor based design as per EPA specifications, Particle Separation: Omni-directional air inlet with PM 10 separation through an impactor, Sampling Rate : The sampling rate is held constant at 1m3/hr by a suitable critical orifice. The reduced sampling rate allows the sampler to operate continuously for 24 hours even in areas having Filter holder designed to accept standard 47 mm diameter filter media/PTFE Membrane, Filter media : Low noise, brushless motor driven

91. Working Model of Rope

rope haulage.

Sible and Double Drum Direct

Haulage, Endless Haulage, Main and

Tail Haulage All Metal Fabricated

with Wooden base and table mounted

92. Rock Shear Testing Machine Steel fabricated compatible for UTM

93. Multi-Point Borehole Extensometers

Suitable for 76mm diameter downward bore holes from the

surface, Length of the hole 100 to200m for each extensometer

(to be quoted on per m basis; length will be depending on the

site requirements)with 5 grout able anchors with each

extensometer; and steel rods & pipes of suitable length, and a

mouth headpiece Read-out unit compatible with the above

grouted type extensometers using dial caliper (range:

200mm;accuracy +/- 0.1mm)

94. METHANE GAS TESTING CHAMBER

Tailor made chamber having robust construction with Teak

Wood consisting of clear glass in all four sides to have a clear

view for 3-4 trainees at a time Size: Length-12" Breadth-12"

Height-18" (Leg attached with best quality rubber buffer).

Comprised with LP Gas Cylinder, Gas Pipe, Regulator, Gas

Socket a complete Velox GL7 Safety Lamp & Gas Cap Indicator

Wooden Box with all necessary spares and accessories

95. Muffle Furness with different

crucible and sample weighing

machines

Temperature range 1500 to 2000 degrees centigrade

96. Model for Mechanized Opencast Coal

Mine:

The model must give a concept and overall layout of a

mechanized opencast coal mine at an advanced stage, Relevant

provisions of Coal Mines Regulations have been followed as far

as practicable. The model shows top soil surface at sides,

benches in overburden of soil and in sand stone, coal bench,

barriers at boundaries, overburden dump with reclaimed land,

inclined coal seam, decaled area, appropriate stop angles of

different benches & barriers & overburden dump, haul road,

ramps, gradients at different places and fence around

workings, Also will be supplied various opencast machines viz.

shovel, dumper, drill, pump etc. Model will be multi-colored to

make itself explanatory and will be covered by transparent

sheets. Profusely labeled by paint

Size: 1.75mx1.75mxheight 70 cm approx.

97. Model for Pit-bottom Layout for Cage

Winding:

The model must show the track layout at pit-bottom area

suitable for Endless Rope Haulage working on; shaft level up to

pit-bottom area. Model shows appropriate gradients at

different places, position of Endless Rope Haulage engine, ;the

shaft with protective roofs on its both sides, shaft pillar, shaft

level road, stop-blocks, bye-pass road to bring empty tubs from

one side to other side of shaft. Model will also show an inclined

gantry with creeper which can be operated by a handle to raise

tubes and thus making the model working, Two coal tubs will

be provided. There are sliding transparent sheets covered

windows at gallery roof to show interior details & to operate

the model duly labeled by paint.

Size: 2.1mx0.7mxheight 60cm approx.

98. Model for Pit-top Layout with

Turntables:

The model shows the track layout at pit-top with two

turntables on two sides of the shaft. The turntables are

mounted on rollers and are fitted with tub guides. The model

comprises a side-on tippler mounted on rollers & having chain

driving mechanism, chute, track for material supply and two

coal tube. Te tripper can ob operated by handle to tipple tubs.

Only pit-mouth with shaft will be shown and without headgear.

Duly labeled by paint.

Size: 155mx70cmxheight 40 cm approx.

99. Model for Skip (Bottom-discharge

Type):

The skip is mounted upright on a base board and it has all the

usual fittings viz. loading door, discharge door fitted with guide

roller & spring-loaded catch, rail guide-shoe, shoe for receiver,

anti-breakage plate & its balance weight, inspection door skip

suspension link etc. Skip body is made of acrylic sheet. Duly

labeled by paint.

Size: 42cmx32cmxhieght 70cm approx.

100. Model for Shaft- Sinking: This model must give an overall concept about the general

arrangements of sinking a vertical circular shaft through

ordinary strata. It shows the essential surface plants &

equipments as well as sinking arrangement & appliances in the

shaft also. The model shows an aluminum member made 6-

legged headgear with its usual construction & fittings mounted

on a high table over a shaft, three pulleys on headgear, winding

drum for kibble, double-drum capstan for walling: platform,

upper & lower folding doors, chute with a platform around it,

tramline & a tub for debris disposal, shaft centering apparatus,

air tube for ventilation compressed air pipe, electric cable reel

and shot-firing cable reel. Model also shows sinking bucket of

kibble with its suspension gear including clivvy & safety hook

whereby over wind can be demonstrated by rotating the

winding drum with a handle, rider, walling platform with its

constructional details & its suspension arrangement from

headgear, in cut-section of the shaft are shown details of

temporary supports & permanent lining which comprises

walling curb, steel curb, hanger, backing deal with wedges,

radius rod, emergency rope ladder etc. It is a working model

profusely labeled by paint.

Size: 1.6mx65cmxheight 2.2 approx.

101. Model for Winding Installation:

This model must give an overall concept about the installation

of a system of drum winding with cages that are commonly

found in vertical shafts in collieries. An aluminum member

made 6 legged headgears with its usual construction & fittings

like two pulleys, a ladder, platform & fence at top: is mounted

on a high table over a G.I. sheet made shaft. Model shows

winding engine room with winding drum showing its

constructional features, pit-top & pit-bottom track layouts

(partly), two aluminum made cages with their usual fittings &

with their suspension gears whereby function of safety hook on

over-winding can be demonstrated by rotating the winding

drum by a handle, eight keeps operated by handles, eight steel

rope guides, shaft fence, stop blocks and three coal tube.

Model duly labeled by paint.

Size: 1.7mx0.63mxheight 1.9 approx.

102. Model for Cage Suspension Gear:

This model must show a 6-legged aluminum member made

headgear mounted on a base board with a circular shaft cut in

it. The model comprises a headgear fitted with one headgear

pulley & detaching plate, winding drum, on aluminum made

cage, all equipment of suspension gear viz. reliance cappel,

safety hook, distribution plate, D-links and cage chains. Over-

winding may be demonstrated. Model labeled by paint.

Size: 900cmx35cmxhieght 85cm approx.

103. Model for Friction or Koepe Winding

System-Tower Mounted Winder:

This model must show the basic features of a single rope tower

mounted koepe winder with cages. An aluminium member

made 4legged headgear with fittings like ladder, platform and

fence at top is mounted on a high table over a G.I. sheet made

shaft. On the platform at headgear to be mounted the single-

rope Koepe Pulley showing its constructional features and the

deflection pulley is fitted at a lower level on the headgear. The

model also comprises pit-top & pit-bottom track layouts

(partly), two aluminium made cages with their usual fittings are

hung from two ends of a single winding rope by suspension

gears, a balance rope fixed beneath two cages, eight steel

guide ropes, shaft fence, stop-blocks and three coal tubs.

Working of the winding system can be demonstrated by

rotating the Koepe Pulley by a handle. Duly labeled by paint.

Size: 1.7mx0.63mxheight 2m approx.

104. Model for Long wall Retreating Face

with Caving:

This model shows a mechanized longwall retreating face with

caving and layout of the adjacent area in the panel. The model

shows-the longwall retreating face with virgin coal on the

outbye side and goaf area on the inbye side in the panel, main

& tail gate roads with roof supports by bars on hydraulic props,

armoured flexible conveyor fitted with spill plate, trough for

cable & hydraulic duct and rack-atrack, stage loader mounted

on track, gate belt conveyor, track for material supply & energy

train containing power pack, switch gears, Anderton shearer

DERD, with drums having spiral lacing of picks & sprocket for

hauling the machine on rackatrack- Anderton shearer shown ;in

cutting position at face, ;shield support, hydraulic ram, face

pump with sump, caved in goaf and spraying water pipe for

shearer. Model covered by transparent sheet. Exhaustively

labeled by paint.

Size: 1.3mc1.2mxheight 44cm approx.

105. Slack Durability Index Apparatus

Two sets of drums of the lengthof at least 100 mm and the diameter of at least 140 mm.Drums rotate in water that had a level of about 20 mm below the drum axis. Rotation must be driven by a motor capable of rotating the drums at a constant speed of 20 rpm.

106. High volume sampler

model – I

Volumetric flow range: Nominal 45-96m3/hr Flow accuracy: Better than ± 1m3/hr Vacuum Capability: 140 mBar max Temperature range: 0-50oC Filter size: 250 x 200mm (rectangular element) Weight: 45 kg Dimensions: 380 x 380 x 1200 mm (WxDxH) Power: 200-240V ±10% 50/60 Hz (std) External inputs: Wind direction sensor input (10k potentiometer) Wind speed sensor input (contact closure) or alternatively

Tipping bucket rain gauge Data storage up to 150 reading (75 hours of 30min averages) Data accessible via GSM modem

107. Temp, humidity, pressure, wind

speed auto recorder

Wind Speed : range 0 to 100 Km/hr.

Wind Direction :

range 0 to 360 degrees with 1 degree resolution

Temperature & RH :

range 0 to 50 C with resolution of 0.1 C and 0 to 100% RH with

1% resolution.

Solar Radiation :

Li-Cor, USA Solar Radiation Sensor

Barometric Pressure :

Met One, USA Barometric Pressure Sensor

Rainfall :

range 0 to 50 mm/hr with 0.5 mm resolution

The standard system supplied with Sensors for Wind Speed,

Direction, Temperature and Relative Humidity. Other sensors

for Barometric Pressure, Solar Radiation & Rainfall are optional

and can be provided at extra cost.

Memory Capacity : at last Forty five days storage of all

parameters in non-volatile flash memory.

Real Time Sync : Built-in battery backed Real time clock

ensures data is synchronized with real-time even after

periods of prolonged power failure.

Software : Windows XP compatible, software is

provided for data download to a PC and analysis. MetLog

supports communication via PSTN, GSM modems and direct

cable connection to RS232 / USB ports. Analysis tools include

export to MS Excel, Graphs, Monthly Averages & Windrose

Diagrams.

108. Konimeter with All Accessories, Battery Driven and Backup Battery

DST-06- List of Drilling Technology Equipments


1.

Resistivity meter Model SSR-

Input power source : 24V rechargeable batteries

Input power source : 24V rechargeable batteries

MP-ATS (IGIS)

Power output : 100 watts (Current upto 2 Amp)

350V(700V peak to peak) automatic voltage selection

Frequency : 0.8Hz (Approx.)

Noise rejection : 95 db

Potential measuring range : Microprocessor based unit

with measurement resolution of 10 micro volts

Range selection: Automatic

Resistance range: 10-5 to 104 ohms

Self potential cancellation: Automatic

Resistance range: 10-5 to 104 ohms

Self potential cancellation: Automatic

Dynamic range: 15 bits

Data averaging: Upto 16 cycles

Input impedance: 1 Mega Ohm

Accuracy: + 1%

Interaction with the system: User friendly menu operation

with 4x3 feather touch

key pad and 16x2 Alphanumeric Liquid Crystal Display

Measurement display: Stack No./Stacks selected, next line

current and running

Average of average of resistance

Output: Survey code, Date, Time, Display of Electrode

spacings,

Resistance, Apparent Resistivity and Longitudinal

Conductance through16x2 Alphanumeric Liquid

Crystal Display

Data transfer: The data can be transferred directly to any

windows based

PC through RS 232 port for analysis and interpretation

Depth penetration: upto 600 m under favorable geological /

field conditions

Multi electrodes connecting swithch box interface

2.

Computer System (High Speed

latest model)

Processor

2nd Generation Intel(R) Core(TM) i3-2120 Processor

Operating System

Genuine Windows(R) 7 Professional SP1 64bit (English)

Memory

6GB DDR3 SDRAM at 1333Mhz - 2 DIMMS

Hard Drive

500GB SATA hard drive (7200RPM)

Optical Drive

DVD-ROM DVD+/-RW

With key board, mouse and 36 inch LCD monitor

3. Computer System Complete Set Processor

3rd Generation Intel® Core™ i5-3450 Processor

(3.10 GHz, 6MB Cache, with Turbo Boost

Technology 2.0)

Operating System

Windows® 7 Home Premium SP1 64 bit (English)

Memory3

8GB3 Dual Channel DDR3 SDRAM at 1600MHz

Hard Drive

1TB SATA 3.0Gb/s Hard Drive with Native Command

Queuing

Video Card

1GB GDDR5 NVIDIA® GeForce® GT 545

Optical Drive

Slot-Loading Dual Layer DVD Burner (DVD+-RW,

CD-RW)

Monitor

26” LCD

4. Continuous well Logger

Model DMPL2(IGIS)

Electrical Log

* Self Potential ( SP) : 0 to + 2000mv

http://www.dell.com/mc.ashx?id=technotes:graphics-and-system-memory&c=in&l=en&s=dhs&modalwidth=400&modalHeight=150&ovropac=0&modalscroll=yes&modaltarget=div&modaltype=tooltip&position=bottom&title=Important%20Details&flip=false&eventType=rollover

http://www.dell.com/mc.ashx?id=technotes:graphics-and-system-memory&c=in&l=en&s=dhs&modalwidth=400&modalHeight=150&ovropac=0&modalscroll=yes&modaltarget=div&modaltype=tooltip&position=bottom&title=Important%20Details&flip=false&eventType=rollover

* Resistivity ( SN & LN ) : 0.1 – 20,000 Ohm m

* Resolution : 1/20,000 FSD

Recording Unit

* Notebook PC : Intel Celeron P.C

* Inkjet Printer : Compatible with P.C.

Power

* Rechargeable : 12V, 7 Ah Battery

Winch Unit

* Cable Capacity: 300 Mts. of 3 core

* Depth measurement: Incremental Shaft encoder

And Mechanical counter.

* Winch drive: Motor / Hand driven

* Power: 1KVA Generator

Water level indicator

Length of the cable: 100m

Indication: Analog Panel Meter & Buzzer

Sound

Power Supply: 9 Volts battery

Weight: 5.0 Kgs. Approximately

5. Digital Balance

Top loading, convert with glass from sides capacity 60 – 210

grams. Accuracy 0.01 – 0.1 mg

6. Digital pH meter

Display : 31/2 Digit 12.7 mm LED Range : pH 0.00 to 14.00

mv Accuracy : 0.01 pH +- digit temperature compensation :

0.100 deg manual, 540 Atomatic power supply 230 V = -10

Hz Recorder output 100m V/pH Ds Titration output:

Polarization current output provided Approx Diam in mm

(HXWXD): 60X255X180 Approx weight : 1.4kg standard

accessories: Buffer solution pH 4 & 7 125 ml each Electrode

stand with clamp optional Accessories: Buffer solution pH 4

& 7 125 ml each Electrode stand with clamp

7. Exploration seismograph

24 channels geophones with

A/D Conversion: 24 bit result using Crystal Semiconductor

sigma-delta converters and Geometrics proprietary

oversampling.

software and all accessories

DynamicRange: 144 dB (system), 110 dB (instantaneous,

measured) at 2ms, 24dB.

Distortion: 0.0005% @ 2 ms, 1.75 to 208 Hz.

Bandwidth: 1.75 Hz to 20 kHz. Low corner frequency option

available.

Common Mode Rejection: > -100 dB at <=100 Hz, 36 dB.

Crosstalk: -125 dB at 23.5 Hz, 24 dB, 2 ms.

Noise Floor: 0.2uV, RFI at 2 ms, 36 dB, 1.75 to 208 Hz.

Stacking Trigger Accuracy: 1/32 of sample interval.

Maximum Input Signal: 2.8 VPP.

Input Impedance: 20 kOhm, 0.02 uf.

Preamplifier Gains: SGOS software enables selectable gain

pair of either 24 or 36 dB. MGOSsoftware selection between

jumpered gain pair 12 and 24 dB, gain pair 24 and 36 dB, or

0dB.

Anti-alias Filters: -3 dB at 83% of Nyquist frequency, down

90 dB.

Pre-trigger Data: Up to 4,096 Samples. Optional event

detection software enables system for earthquake, vibration

monitoring.

Sample Interval: 0.02, 0.03125, 0.0625, 0.125, 0.25, 0.5, 1.0,

2.0, 4.0, 8.0, 16.0 ms.

Record Length: 16,000 samples standard, 64,000 samples

optional 2

Delay: 0 to 9999 ms in 1 ms steps.

Data Transmission: Uses reliable Ethernet connections and

requires no custom transmission software. Interfaces

directly with Windows OS.

Auxiliary Channels: All Geode channels can be programmed

as either AUX or DATA.

Instrument Tests: Optional built-in analog testing available.

Tests provided: noise, crosstalk, total harmonic distortion,

gain similarity, gain accuracy, common-mode rejection,

trigger accuracy

Acquisition and DisplayFilters:

LowCut: OUT, 10, 15, 25, 35, 50, 70, 100, 140, 200, 280, 400

Hz, 24 or 48 dB/octave, Butterworth.

Notch: 50, 60, 150, 180 Hz and OUT, with the 50 dB rejection

bandwidth 2% of center frequency.

HighCut: OUT, 250, 500 or 1000 Hz, 24 or 48 dB/octave.

LineTesting: Real time noise monitor displays real-time

output from geophones. Optional geophone pulse test helps

identify bad geophones and shorted or broken cables.

Data Storage: Stores data on local hard drive,

local RAID, or NAS. Tape support available under

Windows XP.

Triggering: Positive, negative or contact closure, software

adjustable threshold.

Data Formats: SEG-2 standard with SGOS. SEG-D and SEG-Y

available. 2

Power: Requires 12V external battery. Uses 0.65 W/channel

during acquisition, sleep mode reduces power consumption

by 70% while in standby.

Plotters: Drives most Windows-compatible printers and

plotters

Environmental: -30 to 75 degrees C. Waterproof and

submersible. Withstands a 1 m drop onto concrete on 6

sides and 8 corners.

Operating System: Windows XP/W2K/ME/98/NT/Vista. An

older, limited feature version of the software is available for

95

8. Hand crank viscometer

Rotational Speed 300 to 600 rpm. Good quality torsion

spring. 12 volt motor.

9. HIGH VOLUME SAMPLER With

Digital Display

Heavy gauge Aluminum body, Compact and robust with

front and side panel door and gable roof.Blower :

Neutron/similar make heavy duty blower having free flow

rate of 1.5 M3/ min which will operate on 230 VAC, 50 HZ .

Filter Holder : Aluminum Filter holder having SS mesh with

rubber gasket to accommodate filter paper of

8” X 10” size.Rotameter : Flow point /similar make 0.3 to 3

LPM acrylic body Rota meter for measuring flow

rate for gaseous sampling.Manifold : Acrylic body manifold

with SS needle valves with four inlets and one outlet for

measuring four gaseous samples at a time. sImpinger : Glass

impinge tubes of 35ml capacity – 2nos.Impinger box : Acrylic

body impinge box to accommodate glass

pingers.Manometer : U Tube 20- 0 – 20 Glass manometer

.Stabliser : Voltage stabliser to stablise the voltage

fluctuations 170- 270 volts, 0.5 KVA. Stabliser does not

include Ampere Meter.Timer : 24- Hour Programmable timer

with facility to pre set timings of the actual sampling

duration of the HVS.Time Totaliser : Hour meter to measure

the actual duration of the running of HVS.Filter paper :

Whatman make GFA 8”x 10” size , Glass fiber filter paper for

SPM Measurement 100 nos.Carbon Brush : For

Routine running of the blower .Brushless Motor we have

offered.Gas Attachment : For Collection of Gas sample So2 ,

NOX, Co2, CO.

10. Large format Scanner cum

printer 36 inch Size, colour

Functions Print, copy, scan

Print speed 51 m²/hr

Print speed color line drawing (draft, A1 plain paper) 80 A1

prints per hour

Print speed color line drawing (draft, US D plain paper) 80 D

prints per hour

Print speed black line drawing (draft, A1 plain paper) 80 A1

prints per hour

Memory, standard 32 GB

Hard disk Standard, 160 GB

Print technology HP Thermal Inkjet

Number of print cartridges HP Thermal Inkjet 6 (cyan, gray,

magenta, matte black, photo black, yellow)

Compatible ink types Dye-based (C, M, Y, G, pK); pigment-

based (mK)

Roll maximum output 91 m (application dependent)

Guaranteed minimum line width 0.06 mm (ISO/IEC

13660:2001(E))

Line accuracy +/- 0.1%

Connectivity, standard Gigabit Ethernet (1000Base-T); EIO

Jetdirect accessory slot; Hi-Speed USB 2.0 certified

Print languages T2300 PostScript eMultifunction: Adobe

PostScript 3, Adobe PDF 1.7, TIFF, JPEG, HP-GL/2, HP-RTL,

CALS G4, HP PCL 3 GUI T2300 eMultifunction: TIFF, JPEG, HP-

GL/2, HP-RTL, CALS G4, HP PCL 3 GUI

Finished output handling Printer: sheet feed, two automatic

roll feeds, automatic roll-switching, automatic cutter;

scanner: straight-through scan paper path for sheet and

cardboard originals

Media types Printer: bond and coated paper, technical

paper, film, photographic paper, backlit, self-adhesive;

scanner: non-abrasive paper, vellum, translucent, opaque

Mylar, recycled, blueprints, cardboard (No plywood, stone

plates, metal plates or abrasive, dirty, rough, sharp edged,

metal clamped, or burned surfaces or transparencies)

Media sizes standard (metric rolls) A4 to A0-size sheets; 279

to 1118-mm rolls

Roll external diameter 135 mm

Media thickness Up to 31.5 mil

Linear scan speed Up to 3.81 cm/sec (color, 200 dpi); up to

11.43 cm/sec (grayscale, 200 dpi)

Scan quality colour (best) 600 dpi

Scan resolution, optical 600 dpi

Scan resolution, hardware 600 x 600 dpi

Scanner type Sheetfed, CIS (Contact Image Sensor)

Scan size (flatbed), maximum 91.4 x 237.8 cm

Copy reduce / enlarge settings 25 to 400%

Copies, maximum Up to 99 copies

Compatible operating systems T2300

eMultifunction: Microsoft® Windows® 7

Ultimate/Professional/Home Premium, Windows Vista®

Ultimate/Business/Home Premium, Windows® XP (32-bit,

64-bit)

T2300 PostScript eMultifunction: Microsoft® Windows® 7

Ultimate/Professional/Home Premium, Windows Vista®

Ultimate/Business/Home Premium, Windows® XP (32-bit,

64-bit) Professional/Home, Windows® Server 2008 (32-bit,

64-bit), Windows® Server 2003 (32-bit, 64-bit); Mac OS X v

10.4, v 10.5, v 10.6; Citrix XenApp; Citrix XenServer; Linux

(see http://www.hplip.net)

11. Laser Distance meter, measurement from cm to 200 meter, Resolution in mm,

output display digital type min. 3 1/2 digits,

12. Low Pressure filter press

Filter press upto 100 +- psi, mud reservoir, gas pressure

supplied with graduated cylinder

13. Marsh Funnel

6 inches diameter at the top and 12 inches long and tapers

to join a tube 2 inches long and 3/16 inches inside diameter.

The capacity of the funnel to the bottom of the wire screen

in 1500 cc.

14. Microprocessor Based Water

& Soil Analysis kit.

pH Cond. TDS DO ORP Salinity Temp.

Range 0 to 14 pH 0-20, 0-200 uS, 0-2, 0-20, 0-200 ms 0-20, 0-

200 ppm, 0-2, 0-20, 0-200 ppt 0-20 ppm 0 to ± 1999.9 mV 0-

20, 0-200 ppm, 0-2,0-20, 0-50 ppt 0-1000C

Res 0.01 pH 0.01 pH 0.01 pH 0.1 mV 0.1 mV 0.01ppm 0.1ºC

Accuracy 0.01 ± 1 Digit ± 0.5% FS ± 1Digit ± 0.5% FS ± 1Digit

0.1 ppm ± 1Digit ± 0.1 mV ± 1 Digit ±1% of Range ± Digit 0.10

ºC ± 1 Digi

Temp. Comp. 0 to 1000C 5-500C (Auto/ Manual) Auto/

Manual Auto/ Manual (5 to 550C) Auto/ Manual

Sensor 0 to 100ºC (Auto/ Manual) Cond/ Salinity/ TDS cell

Cond/ Salinity/ TDS cell Cond/ Salinity/ TDS cell Platinum

Cond/ Salinity TDS cell Semi Conductor Type

Cal Auto & Manual Auto

Ref Temp Selectable (5-50ºC) Selectable (5-50ºC)

Auto Buffer Recog. 4.00, 7.00 & 9.2 pH

Range Automatic Automatic Automatic

Cell Constant Adjustable (0.05 to 10.5) (0.05 to 10.5) (0.05

to 10.5)

Power Supply 6V Rechargeable Battery or 230 ± 10%AC,

50Hz.

Accessories pH Electrode, Cond./TDS Cell, Temp. Probe, DO

Probe, DO Membranes

Tablets 7 pH & 4 pH, Main Lead and Operation Manual.

15. Model of Boring Machine: The model shows the general arrangement of such method

of boring with all the boring tools & equipments viz. derrick,

winch, hoisting rope, rocking lever, hollow bore rod, drill bit,

brace-head, water swivel & hose, two pulleys at derrick &

suspending pulley, settling tank, pump to flush water etc.

Cut-section of ground and bore hole are shown with bore

rod & drilling bit. Model duly labelled by paint. Size : 1 m X

0.7 m X height 1.5 m

16. Model or parts of old drill

machine for study in lab

1. Drill Hammer

2. Wagon drill m/c

3. DTH drill m/c

4. DTH hammer & bits

5. Drill bits

6. Rock roller bits

7. Core barrels single

8. Derrick / tripods

9. Fishing tools (left hand recovery rod)

10. Pulley, clevis & bolts

11. Wire ropes

12 Foot clamp & jaws

13 Reamer & reamer shell

14. Disassembly & assembly practice on non-functional

machines.

17. Motor Driven Viscometer

Knurled hand wheel, output speed 300 – 600 RPM with built

-in digital display meters for measurements

18. Mud Balance

Good quality of arm, graduated scale in centimeter and

inches which consist of a cup at one end and a lid at other

end. Arm with sliding weight. A sharp knife edge on the arm

rests on the supporting base, covering box.

19. Multi parameter, pocket sized

meter for pH, conductivity,

TDS, salinity and temperature

Combine measurement

capabilities of three testers in

one convenient pocket-sized

unit

Range

pH: 0.0 to 14.0

Conductivity: 0 to 200 uS; 201 to 2000 uS; 2.01 to 20.00 mS

Salinity: 0 to 999 ppm

Temp: 32 to 122°F (0 to 50°C) 2.01 to 10.00 ppt

Resolution

pH: 0.1 pH

Conductivity: 10 uS, 0.1 mS

TDS: 0.1 ppm, 1 ppm; 0.01 ppt

Salinity: 0.1 below 100 ppm/1 ppm above

Accuracy

Temperature: 0.1°

pH: 5 points

Conductivity: 3 points

TDS: 3 points Salinity: 1 point

Electrode

Replaceable pH: single-junction

Conductivity/TDS/salinity: dual-pin stainless steel

Waterproof/Dustproof (IP67) Yes

Operating Temperature 0 to 50°C (32 to 122°F)

Power batteries (included), Eveready A761 LR44 equivalent

replacement

Battery life Approximately 250 hours continuous use

20. Sand content tube

Screen set with 200 mesh sieve, 2.5 inches in diameter,

fastened inside a collar upon either end of which fits a small

funnel, a glass measuring tube calibrated from 0 to 20%

21. Software

Latest academic versions

A. Geomedia GIS - GIS analysis, spatial editing

software, terrain analysis and visualisation,

seamless integration of vectors & grid data

formats

B. Image Processing Suite – ERDAS - advanced

remote sensing & spatial modelling C. Imagine Photogrammetric Suite – LPS -

automatically generate terrain data from images. 22. Software- GRAM ++ & ILWIS Latest academic version

DST-07- List of Metallurgy Engg. Equipments


1. Muffle Furnace (For

Heating metals &

alloys)

Temp.= upto 1500 deg celsius, chamber size=

300x200x200mm, Box type Furnace, Digital

display of temperature.

2. Jominey

hardenability test

machine

Complete set for hardenability test with hot

sample fixture, steel tongs, waterjet

arrangements for end quenching of samples.

3. Induction heating

furnace

For surface hardening of metals. Temp.: 0-

1500 deg Celsius, chamber size=

300x200x200mm, 3ph. AC supply.

4. Rolling Mill Model

(Lab size)

For study, 2 high, 2 stand, Reversing type with

motor, For rolling of soft metal like Aluminium.

5. Wire Drawing Bench

(Lab size)

Draw bench with complete set for study of

wire drawing operation.

Max. wire diameter with mild steel:

Max. wire diameter with alloy steel:

Draw force: upto 1800 Kg

Drawing speed: upto 30meter/min.

6. Gas welding machine Complete set for joining of metals,

welding torch.

Two gas cylinder (one for oxygen and another

for Acetylene gas),

Safety glass, safety accessories.

7. Arc welding machine with complete set, welding machine with

welding electrodes, with safety accessories.

Welding power source.

8. Ball Mill (lab size) Steel ball for grinding of ores and minerals.

Size=15"dia x 21" long.

Complete with 1/2 HP, 11/220V integral gear

motor.

Ball charge required= 205 lbs

9. Rod mill (Lab Size) Rod mill (Lab Size)

10. Jaw Crusher Operation: 440V,AC 3Ph. 50Hz, Complete with

3HP motor.

Jaw size=150-200mm

Capacity=350Kg

Max. size of feed= 50mm

11. Sieve Shaker Frang Depth=50mm

mesh=screening medium with opening,

uniform size and shape, made of woven,

punched or electrodeposited material.

pan- stamped or spun receiver of materials

passing the sieve.

Test sieves of different opening sizes.

12. Wilfley table with

complete accessories

(Lab. Purpose)

Wilfley table with complete accessories (Lab.

Purpose) motorised Motor Power: 1.1KW,

Dimension(L*W*H): 4450*1855*1546 mm

13. Low power

microscope

For examination of castings

Magnification=50x

14. Permeability tester metallic mould: 100mm dia x 127mm height,

1000 ml volume.

extension caller: 100mm dia x60mm high, with

dummy plate and porous stone.

Rubber connection tube: 3mm long with pinch

cock,

Rammer: 2.6Kg x 310 mm controlled fall

Rammer: 4.9Kg x 450 mm controlled fall

15. Rapid moisture teller sand testing equipment for total clay content

of sand sample.

width=300mm

depth=300mm

ht.=500mm

wt.=26Kg

16. Single pan analytical

balance

Max. capacity=510 gm

Readability=0.001 gm

Linearity=±0.002 gm

Setting time=3 sec.

17. Electric Arc Furnace

(Lab size)

For melting of metals.

Temp. range: upto7800 deg C

Capacity: 100 kg

3Ph UHP (Ultra High Power) with three

graphite electrodes.

Mine- ABB, DEMAG

18. Radiation Pyrometer For measuring high temp. of molten metal and

/ metal casting.

temp.=upto 2000 deg C

Temp resolution: at 300ms, 100deg C,

emissivity=1

Spectral response- 8-14

Operating voltage: 15 to 32 V DC

19. Metallurgical

Microscope

Eye piece tube: Inverted tri-ocular eye piece

tube.

Total magnification= 1000x

Illumination unit=60V, 20W Halogen lamp,

adjustable brightness: 220V/50Hz, with 20

standard samples of different alloys

20. Sample cutting

machine

cut off wheel dia: 75mm - 152 mm

thickness of cutoff wheel= 0.3 to 0.8mm

cutoff wheel speed = 300-5000 rpm

cutting capacity= upto 50 mm dia

Min. length of sample to be clamped=200mm

Recirculating cooling unit= 2-4 litres

21. Sample grinding

machine

For metals, grinding disc=2

disc dia. =200 mm

rpm= 150/300

3 ph, 380V, 50Hz

22. Sample polishing

machine

Dual wheel polisher

Wheel dia=200 mm

speed of polishing wheel = 600 rpm

power supply = 220V, 50Hz

Max. dia of specimen = 50 mm

23. Magnetic particle

testing machine /

Magnaflux testing

machine for

detecting flaws in

ferrous materials

Horizontal magnetic particle inspection

machine,

Power supply output: 3000 Amp AC

Floor space required= 36" x 60"

24. Ultrasonic testing

machine

with probes and transducer.

For testing of ferrous and non-ferrous metal

casting.

25. Fatigue testing

machine

(For checking strength of materials in

fluctuating load conditions)

Rotating beam reversed bending fatigue test.

working temp: at room temp.

26. Creep testing

machine

For testing strength of a material at constant

load and elevated temp.

27. Vicker's hardness

testing machine

For hardness test of materials, with diamond

pyramid intender with Vicker's hardness table.

DST-08- List of Physics Equipments

Sl. No. Name of Equipment Specifications

1. Vernier caliper / Digital caliper Stainless steel Vernier, reading to 0.01 cm, with wheel

drive

2. Micrometer screw gauge Circular brass body with stainless steel screw & pivot,

ratchet stop, (Moore & Wright type), 25x1/100 mm

3. Meter Bridge One meter long, double laminated board, 3/4" wide

copper strips, Spring type jockey sliding on a nickeled

metal rod, 2-gaps type

4. Potentiometer 10 wires, one meter long, composite jockey with 10

contact points, sliding on metal rod.

5. Thermocouple a) Iron & Copper pain on wooden stand.

b) Antimony & Bismuth pain on wooden stand.

6. Searle's thermal conductivity

apparatus

a) Copper rod 12" long & 1 1/3" in diameter.

b) Thermometer - 0-110x1/2C

7. Stroke's method for coefficient experimental setup

8. Surface Tension experimental setup

9. Boyle's Law verification Metal base with levelling screw.

10. Glass Prism Equilateral.

a) with optic axis parallel to refracting edge, size- i)

12.5x12.5 mm, ii) 15x15 mm

b) with optic axis parallel to base, size- i)

12.5x12.5 mm, ii) 15x15 mm

11. Bunsen's photo meter with lamps & optical bench, assembly mounted on 1.5

meter long double bar bench with M.S. rods, with

rider & lamp

12. Resonance apparatus with brass tube & brass reservoir, tube diameter: 1.5"

13. Photoelectricity Photo cell characteristics apparatus with power

supply & 2 analog meters

DST-08- List of Chemistry Equipments Sl. No. Name of Equipments Specification

1 Auto titrator For laboratory experimental purpose

2 Basin For laboratory experimental purpose

3 Beaker of different capacity From 250ml to 1Lt, For laboratory experimental purpose

4 Bunsen burner For laboratory experimental purpose

5

Chemical Balance

For minimum measurement of micrograms, ranging upto 5 gm,

For laboratory experimental purpose

6 Clamp and boss head For laboratory experimental purpose

7 Conical Flasks from 100ml to 1 lt., For laboratory experimental purpose

8 Cork - borer For laboratory experimental purpose

9 Cork - presser For laboratory experimental purpose

10 Crucible and lid For laboratory experimental purpose

11 Deflagrating spoon For laboratory experimental purpose

12 Desiccators For laboratory experimental purpose

13 Distillation set for 1 lt., For laboratory experimental purpose

14 Electrodes Electrodes for pH, TDS, Conductivity for pH meter model no

DP505, TDS meter 509, conductivity meter D511 with standard

solutions / buffer. (Please check the said meters kept in lab

before filling tender)

15 Fukani For laboratory experimental purpose

16

Funnels

from 50mm to 100mm upper flank dia., For laboratory

experimental purpose

17 Gas jar For laboratory experimental purpose

18 Kipps Apparatus For laboratory experimental purpose

19 Measuring flask - 100ml, 200ml,

250ml, 500ml

For laboratory experimental purpose

20 Mortar and pestle For laboratory experimental purpose

21 Multi parameter, pocket sized

meter for pH, conductivity, TDS,

salinity and temperature Combine

measurement capabilities of three

testers in one convenient pocket

sized unit

Range : pH 0.0 to 14.0

Conductivity : 0 to 200 uS; 201 to 2000 uS; 2.01 to 20.00 mS

TDS: 0 to 100.0 ppm; 100 to 1000 ppm; 01.00 to 10.00 ppt

Salinity : 0 to 999ppm

Temp: 32 to 122.F (0 to 50˚C) 2.01 to 10.00 ppt

Resolution: pH - 0.1 pH

Conductivity : 10 uS, 0.1 mS

TDS : 0.1 ppm, 1 ppm; 0.01 ppt

Salinity : 0.1 below 100 ppm/1 ppm above

Temperature : 0.1˚

Accuracy: pH - 5 points

Conductivity: 3 points

TDS : 3 point

Salinity: 1 point

Temperature : 1 point

Electrode : Replaceable

pH: single-junction

Conductivity / TDS / salinity : dual-pin stainless steel

Waterproof / Dustproof (IP67) : Yes

Operating Temperature : 0 to 50˚C (32 to 122˚F)

Power : batteries (included), Everday A761 LR44 equivalent

replacement

Battery life: Approximately 250 hours continuous use

22 Pair of tongs For laboratory experimental purpose

23 pH meter 3.5 digit digital display type, For laboratory experimental purpose

24 Pipette of different size For laboratory experimental purpose

25 Platinum wire For laboratory experimental purpose

26 Retort stand For laboratory experimental purpose

27 Ring For laboratory experimental purpose

28 Round file For laboratory experimental purpose

29 Spirit lamp For laboratory experimental purpose

30 Test tube brush For laboratory experimental purpose

31 Test tube stand For laboratory experimental purpose

32 Triangular file For laboratory experimental purpose

33 Tripod stand For laboratory experimental purpose

34 Trough china clay For laboratory experimental purpose

35 Turbidity meter For laboratory experimental purpose

36 Weight Box For laboratory experimental purpose

37 Wire gauge For laboratory experimental purpose