DELL 1130 - uninetimaging.com€¦ · First released in December 2009, the Dell 1130 series of ... Dell 1130 Dell 1130n Dell 1133 Dell ... UNINET IMAGING INC. UNINET IMAGING INC.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
DELL 1130 CORE CHANGE UNINET TECH TIPUPDATE: Dell has made a change to their 1130 cores where the drum axle bushing is in the end cap...
REMANUFACTURING THEDELL 1130 CARTRIDGE
By Mike Josiah and the Technical Staff at UniNet
On the left picture you see the older black softer plastic bushing.
The right picture shows the newer (harder) white plastic bushing.
This change was made because the softer black bushings were wearing out in an oblong shape and allowing the drum to move.Depending on the wear, light to severe banding will be seen on the printed page.
In the old style end cap pictures with the black bushings, if you look at the drum axle bearing hole you’ll notice wear marks andthat the hole is slightly elongated. You can also see small strands of plastic hanging off the center of the bearing.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
The new end caps have a new drum axle bearing made of a much harder (and what appears to be) self lubricating plastic.This is an expensive upgrade, so Samsung/Dell must have been having massive issues with these cartridges for them to do that.
With a cartridge that was banding, when we swapped out the end caps, the problem instantly went away and when we moved theend caps around to different cores, the problem followed them.
Take a look at the cores you have in stock. If you have the newer ones with the white plastic bearings, you should be fine,but if they have the older softer black bushings, inspect them carefully. If the hole is not perfectly round, your test prints willshow banding.
No new replacement caps are currently available, but we are currently investigating a replacement bushing and/or end capsystem.
PRINTER INTRODUCTIONFirst released in December 2009, the Dell 1130 series of printers are based on a 19-22ppm engine (depending on the model)with a maximum resolution of 1200 x 1200 dpi. The processor is a 150Mhz chip and comes standard with 8Mb SDRAM.Depending on the model number, other options and specs are available.
The Dell 1130 cartridges do not have a drum cover, and come new with a piece of heavy paper with a thin sheet of foam on theinside taped around the cartridge (see left picture). All new cartridges opened so far have shown some toner leakage on the drumthat would have shown on any prints for at least a few pages.
These cartridges have taken a dramatic change in that there are no screws in the outside of the cartridge at all. There areplastic rivets that need to be cut off, holes drilled and screws installed to hold them back on (see right picture). It’s not a hardprocess and it is covered completely in the instructions.
The standard cartridge (Dell # 330-9524) is rated for 1,500 pages. The high yield cartridge (Dell # 330-9523) is rated for 2,500pages. As with pretty much all cartridges these days the cartridge has a chip and it has to be replaced each cycle.
The 330-9524 has a list price of $62.99 USD* and the 330-9523 has a list price of $87.99 USD**Pricing as of May 2011, in U.S. American Dollars.
MACHINES THAT USE THESE CARTRIDGES SO FARDell 1130Dell 1130nDell 1133Dell 1135n
Cartridge troubleshooting will be listed at the end of these instructions.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
REQUIRED TOOLS1. Toner approved vacuum2. A small common screwdriver3. A Phillips head screwdriver4. Needle nose pliers5. Chisel blade Xacto style knife6. Small drill bit (make sure it matches the self tapping screws)
REQUIRED SUPPLIES1. Toner for use in Dell 11302. New replacement chip for use in Dell 11303. New OPC drum (optional)4. New developer roller (optional)5. New PCR (optional)6. New doctor blade (optional)7. Self-tapping screws (seven); match to drill bit you picked listed above.8. Conductive grease9. 99% isopropyl alcohol10. Drum lubricating powder11. Small tube of silicone caulk
1. Place the cartridge with the handle up, facing towards you.With the chisel blade knife, slice off the heads of the threeplastic rivets. Leave the end cap in place for now.
2. On the left side end cap take the chisel blade knife and sliceoff the heads of the four plastic rivets.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
9. Remove the drum. 10. Remove the PCR from the assembly.
11. Remove the PCR cleaning roller. Clean the PCR with yournormal PCR cleaner.
WARNING: Do not clean the OEM PCR with alcohol, as this willremove the conductive coating from the roller. If the PCR is anaftermarket, follow the cleaning methods recommended bythe manufacturer. If the PCR is an OEM, we recommend it becleaned with your standard PCR cleaner.
12. Remove both the PCR holders by pressing in on the tabs atthe bottom of the holder. These holders need to be removed toallow access to the wiper blade.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
18. Place a small amount of conductive grease in the holders,and install the PCR.
19. The large gear side of the drum axle shaft has conductivegrease on it. Regardless of if you are replacing the drum or not,clean the old grease off, and replace with new.
20. Install the drum and axle from the small gear side of thedrum into the waste hopper. Make sure the keyed end of theshaft is on the small gear side.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
21. On the supply hopper, carefully pry out the fill plug anddump out any remaining toner. The fill plug can be difficult toremove as it is recessed. Take a small common screwdriverand work it around the edge lifting slightly until it comes loose.
22. Remove the developer roller.
23. Remove the two screws from the doctor blade, and removethe blade. Clean out all the remaining toner from the hopper.
24. Make sure the doctor blade sealing foam and thedeveloper rollers seals are clean and intact.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
37. Install the two drum axle arms as shown. The white starter drum separator is different since the cartridge is shipped insidethe printer when purchased. There is a shipping lock inside the printer that forces you to remove the starter cartridge from theprinter in order to remove the printer shipping lock. Once the printer shipping lock is removed the cartridge is then reinstalled.When the starter cartridge is removed, the separator is adjusted to prepare for printing. The standard and high yield replacementcartridges are different in color (black color compared to white in the starter cart) and shape. The drum separator in thereplacement cartridges is adjusted when the cartridge is installed not like the starter cartridge that is adjusted when the cartridgeis removed.
We recommend you position the white starter cartridge drum separator in the “used” position. This will insure that the drum is atthe proper distance from the developer roller.
38. To replace the chip, slice the top of the plastic rivet off with the chisel blade knife.
Drill out the plastic rivet with a small drill, remove the cover and chip.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
39. Install the new chip and cover, and insert a small screwthat corresponds to the hole drilled to hold everything in place.It’s very easy when drilling the hole for this screw to drillthrough into the waste chamber. Place a small amount ofsilicone caulk in the hole and screw before install the screw.
PRINTING TEST PAGESConfiguration Page:1. With the printer in the READY state, press and hold the cancel button for about 5 seconds until the status LED blinks fast.2. Release the button.
Cleaning Page:1. With the printer in the READY state, press and hold the cancel button for about 10 seconds until the status LED blinks fast.2. Release the button.
UNINET IMAGING INC. • BROTHER 1240/1650 • ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGEDELL 1130 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS